STM32F303 Peripheral Coverage

ADC1

0x50000000: Analog-to-Digital Converter

170/170 fields covered.

Toggle register map

Offset	Name	31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	ISR																						JQOVF	AWD3	AWD2	AWD1	JEOS	JEOC	OVR	EOS	EOC	EOSMP	ADRDY
0x4	IER																						JQOVFIE	AWD3IE	AWD2IE	AWD1IE	JEOSIE	JEOCIE	OVRIE	EOSIE	EOCIE	EOSMPIE	ADRDYIE
0x8	CR	ADCAL	ADCALDIF	ADVREGEN																								JADSTP	ADSTP	JADSTART	ADSTART	ADDIS	ADEN
0xc	CFGR		AWD1CH					JAUTO	JAWD1EN	AWD1EN	AWD1SGL	JQM	JDISCEN	DISCNUM			DISCEN		AUTDLY	CONT	OVRMOD	EXTEN		EXTSEL				ALIGN	RES			DMACFG	DMAEN
0x14	SMPR1			SMP9			SMP8			SMP7			SMP6			SMP5		SMP5	SMP4			SMP3			SMP2			SMP1
0x18	SMPR2						SMP18			SMP17			SMP16			SMP15		SMP15	SMP14			SMP13			SMP12			SMP11			SMP10
0x20	TR1					HT1																LT1
0x24	TR2									HT2																LT2
0x28	TR3									HT3																LT3
0x30	SQR1				SQ4						SQ3						SQ2	SQ2					SQ1							L
0x34	SQR2				SQ9						SQ8						SQ7	SQ7					SQ6						SQ5
0x38	SQR3				SQ14						SQ13						SQ12	SQ12					SQ11						SQ10
0x3c	SQR4																						SQ16						SQ15
0x40	DR																	RDATA
0x4c	JSQR		JSQ4						JSQ3						JSQ2			JSQ2			JSQ1					JEXTEN		JEXTSEL				JL
0x60	OFR1	OFFSET1_EN	OFFSET1_CH																			OFFSET1
0x64	OFR2	OFFSET2_EN	OFFSET2_CH																			OFFSET2
0x68	OFR3	OFFSET3_EN	OFFSET3_CH																			OFFSET3
0x6c	OFR4	OFFSET4_EN	OFFSET4_CH																			OFFSET4
0x80	JDR1																	JDATA1
0x84	JDR2																	JDATA2
0x88	JDR3																	JDATA3
0x8c	JDR4																	JDATA4
0xa0	AWD2CR														AWD2CH17	AWD2CH16	AWD2CH15	AWD2CH14	AWD2CH13	AWD2CH12	AWD2CH11	AWD2CH10	AWD2CH9	AWD2CH8	AWD2CH7	AWD2CH6	AWD2CH5	AWD2CH4	AWD2CH3	AWD2CH2	AWD2CH1	AWD2CH0
0xa4	AWD3CR														AWD3CH17	AWD3CH16	AWD3CH15	AWD3CH14	AWD3CH13	AWD3CH12	AWD3CH11	AWD3CH10	AWD3CH9	AWD3CH8	AWD3CH7	AWD3CH6	AWD3CH5	AWD3CH4	AWD3CH3	AWD3CH2	AWD3CH1	AWD3CH0
0xb0	DIFSEL														DIFSEL_117	DIFSEL_116	DIFSEL_115	DIFSEL_114	DIFSEL_113	DIFSEL_112	DIFSEL_111	DIFSEL_110	DIFSEL_19	DIFSEL_18	DIFSEL_17	DIFSEL_16	DIFSEL_15	DIFSEL_14	DIFSEL_13	DIFSEL_12	DIFSEL_11	DIFSEL_10
0xb4	CALFACT										CALFACT_D																CALFACT_S

Toggle registers

ISR

interrupt and status register

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

11/11 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
					JQOVF rw	AWD3 rw	AWD2 rw	AWD1 rw	JEOS rw	JEOC rw	OVR rw	EOS rw	EOC rw	EOSMP rw	ADRDY rw

Toggle fields

ADRDY

Bit 0: ADRDY.

Allowed values:
0: NotReady: ADC is not ready to start conversion
1: Ready: ADC is ready to start conversion

EOSMP

Bit 1: EOSMP.

Allowed values:
0: NotEnded: End of sampling phase no yet reached
1: Ended: End of sampling phase reached

EOC

Bit 2: EOC.

Allowed values:
0: NotComplete: Regular conversion is not complete
1: Complete: Regular conversion complete

EOS

Bit 3: EOS.

Allowed values:
0: NotComplete: Regular sequence is not complete
1: Complete: Regular sequence complete

OVR

Bit 4: OVR.

Allowed values:
0: NoOverrun: No overrun occurred
1: Overrun: Overrun occurred

JEOC

Bit 5: JEOC.

Allowed values:
0: NotComplete: Injected conversion is not complete
1: Complete: Injected conversion complete

JEOS

Bit 6: JEOS.

Allowed values:
0: NotComplete: Injected sequence is not complete
1: Complete: Injected sequence complete

AWD1

Bit 7: AWD1.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

AWD2

Bit 8: AWD2.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

AWD3

Bit 9: AWD3.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

JQOVF

Bit 10: JQOVF.

Allowed values:
0: NoOverflow: No injected context queue overflow has occurred
1: Overflow: Injected context queue overflow has occurred

IER

interrupt enable register

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

11/11 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
					JQOVFIE rw	AWD3IE rw	AWD2IE rw	AWD1IE rw	JEOSIE rw	JEOCIE rw	OVRIE rw	EOSIE rw	EOCIE rw	EOSMPIE rw	ADRDYIE rw

Toggle fields

ADRDYIE

Bit 0: ADRDYIE.

Allowed values:
0: Disabled: ADC ready interrupt disabled
1: Enabled: ADC ready interrupt enabled

EOSMPIE

Bit 1: EOSMPIE.

Allowed values:
0: Disabled: End of regular conversion sampling phase interrupt disabled
1: Enabled: End of regular conversion sampling phase interrupt enabled

EOCIE

Bit 2: EOCIE.

Allowed values:
0: Disabled: End of regular conversion interrupt disabled
1: Enabled: End of regular conversion interrupt enabled

EOSIE

Bit 3: EOSIE.

Allowed values:
0: Disabled: End of regular sequence interrupt disabled
1: Enabled: End of regular sequence interrupt enabled

OVRIE

Bit 4: OVRIE.

Allowed values:
0: Disabled: Overrun interrupt disabled
1: Enabled: Overrun interrupt enabled

JEOCIE

Bit 5: JEOCIE.

Allowed values:
0: Disabled: End of injected conversion interrupt disabled
1: Enabled: End of injected conversion interrupt enabled

JEOSIE

Bit 6: JEOSIE.

Allowed values:
0: Disabled: End of injected sequence interrupt disabled
1: Enabled: End of injected sequence interrupt enabled

AWD1IE

Bit 7: AWD1IE.

Allowed values:
0: Disabled: Analog watchdog interrupt disabled
1: Enabled: Analog watchdog interrupt enabled

AWD2IE

Bit 8: AWD2IE.

Allowed values:
0: Disabled: Analog watchdog interrupt disabled
1: Enabled: Analog watchdog interrupt enabled

AWD3IE

Bit 9: AWD3IE.

Allowed values:
0: Disabled: Analog watchdog interrupt disabled
1: Enabled: Analog watchdog interrupt enabled

JQOVFIE

Bit 10: JQOVFIE.

Allowed values:
0: Disabled: Injected context queue overflow interrupt disabled
1: Enabled: Injected context queue overflow interrupt enabled

CR

control register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

9/9 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ADCAL rw	ADCALDIF rw	ADVREGEN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
										JADSTP rw	ADSTP rw	JADSTART rw	ADSTART rw	ADDIS rw	ADEN rw

Toggle fields

ADEN

Bit 0: ADEN.

Allowed values:
0: Disabled: ADC disabled
1: Enabled: ADC enabled

ADDIS

Bit 1: ADDIS.

Allowed values:
0: NotDisabling: No disable command active
1: Disabling: ADC disabling

ADSTART

Bit 2: ADSTART.

Allowed values:
0: NotActive: No conversion ongoing
1: Active: ADC operating and may be converting

JADSTART

Bit 3: JADSTART.

Allowed values:
0: NotActive: No conversion ongoing
1: Active: ADC operating and may be converting

ADSTP

Bit 4: ADSTP.

Allowed values:
0: NotStopping: No stop command active
1: Stopping: ADC stopping conversion

JADSTP

Bit 5: JADSTP.

Allowed values:
0: NotStopping: No stop command active
1: Stopping: ADC stopping conversion

ADVREGEN

Bits 28-29: ADVREGEN.

Allowed values:
0: Intermediate: Intermediate state required when moving the ADC voltage regulator between states
1: Enabled: ADC voltage regulator enabled
2: Disabled: ADC voltage regulator disabled

ADCALDIF

Bit 30: ADCALDIF.

Allowed values:
0: SingleEnded: Calibration for single-ended mode
1: Differential: Calibration for differential mode

ADCAL

Bit 31: ADCAL.

Allowed values:
0: Complete: Calibration complete
1: Calibration: Start the calibration of the ADC

CFGR

configuration register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

18/18 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
	AWD1CH rw					JAUTO rw	JAWD1EN rw	AWD1EN rw	AWD1SGL rw	JQM rw	JDISCEN rw	DISCNUM rw			DISCEN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	AUTDLY rw	CONT rw	OVRMOD rw	EXTEN rw		EXTSEL rw				ALIGN rw	RES rw			DMACFG rw	DMAEN rw

Toggle fields

DMAEN

Bit 0: DMAEN.

Allowed values:
0: Disabled: DMA disabled
1: Enabled: DMA enabled

DMACFG

Bit 1: DMACFG.

Allowed values:
0: OneShot: DMA One Shot Mode selected
1: Circular: DMA circular mode selected

RES

Bits 3-4: RES.

Allowed values:
0: Bits12: 12-bit
1: Bits10: 10-bit
2: Bits8: 8-bit
3: Bits6: 6-bit

ALIGN

Bit 5: ALIGN.

Allowed values:
0: Right: Right alignment
1: Left: Left alignment

EXTSEL

Bits 6-9: EXTSEL.

Allowed values:
0: TIM1_CC1: Timer 1 CC1 event
1: TIM1_CC2: Timer 1 CC2 event
2: TIM1_CC3: Timer 1 CC3 event
3: TIM2_CC2: Timer 2 CC2 event
4: TIM3_TRGO: Timer 3 TRGO event
6: EXTI11: EXTI line 11
7: HRTIM_ADCTRG1: HRTIM_ADCTRG1 event
8: HRTIM_ADCTRG3: HRTIM_ADCTRG3 event
9: TIM1_TRGO: Timer 1 TRGO event
10: TIM1_TRGO2: Timer 1 TRGO2 event
11: TIM2_TRGO: Timer 2 TRGO event
13: TIM6_TRGO: Timer 6 TRGO event
14: TIM15_TRGO: Timer 15 TRGO event
15: TIM3_CC4: Timer 3 CC4 event

EXTEN

Bits 10-11: EXTEN.

Allowed values:
0: Disabled: Trigger detection disabled
1: RisingEdge: Trigger detection on the rising edge
2: FallingEdge: Trigger detection on the falling edge
3: BothEdges: Trigger detection on both the rising and falling edges

OVRMOD

Bit 12: OVRMOD.

Allowed values:
0: Preserve: Preserve DR register when an overrun is detected
1: Overwrite: Overwrite DR register when an overrun is detected

CONT

Bit 13: CONT.

Allowed values:
0: Single: Single conversion mode
1: Continuous: Continuous conversion mode

AUTDLY

Bit 14: AUTDLY.

Allowed values:
0: Off: Auto delayed conversion mode off
1: On: Auto delayed conversion mode on

DISCEN

Bit 16: DISCEN.

Allowed values:
0: Disabled: Discontinuous mode on regular channels disabled
1: Enabled: Discontinuous mode on regular channels enabled

DISCNUM

Bits 17-19: DISCNUM.

Allowed values: 0x0-0x7

JDISCEN

Bit 20: JDISCEN.

Allowed values:
0: Disabled: Discontinuous mode on injected channels disabled
1: Enabled: Discontinuous mode on injected channels enabled

JQM

Bit 21: JQM.

Allowed values:
0: Mode0: JSQR Mode 0: Queue maintains the last written configuration into JSQR
1: Mode1: JSQR Mode 1: An empty queue disables software and hardware triggers of the injected sequence

AWD1SGL

Bit 22: AWD1SGL.

Allowed values:
0: All: Analog watchdog 1 enabled on all channels
1: Single: Analog watchdog 1 enabled on single channel selected in AWD1CH

AWD1EN

Bit 23: AWD1EN.

Allowed values:
0: Disabled: Analog watchdog 1 disabled on regular channels
1: Enabled: Analog watchdog 1 enabled on regular channels

JAWD1EN

Bit 24: JAWD1EN.

Allowed values:
0: Disabled: Analog watchdog 1 disabled on injected channels
1: Enabled: Analog watchdog 1 enabled on injected channels

JAUTO

Bit 25: JAUTO.

Allowed values:
0: Disabled: Automatic injected group conversion disabled
1: Enabled: Automatic injected group conversion enabled

AWD1CH

Bits 26-30: AWDCH1CH.

Allowed values: 0x0-0x13

SMPR1

sample time register 1

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

9/9 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
		SMP9 rw			SMP8 rw			SMP7 rw			SMP6 rw			SMP5 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SMP5 rw	SMP4 rw			SMP3 rw			SMP2 rw			SMP1 rw

Toggle fields

SMP1

Bits 3-5: SMP1.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP2

Bits 6-8: SMP2.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP3

Bits 9-11: SMP3.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP4

Bits 12-14: SMP4.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP5

Bits 15-17: SMP5.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP6

Bits 18-20: SMP6.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP7

Bits 21-23: SMP7.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP8

Bits 24-26: SMP8.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP9

Bits 27-29: SMP9.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMPR2

sample time register 2

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

9/9 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
					SMP18 rw			SMP17 rw			SMP16 rw			SMP15 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SMP15 rw	SMP14 rw			SMP13 rw			SMP12 rw			SMP11 rw			SMP10 rw

Toggle fields

SMP10

Bits 0-2: SMP10.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP11

Bits 3-5: SMP11.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP12

Bits 6-8: SMP12.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP13

Bits 9-11: SMP13.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP14

Bits 12-14: SMP14.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP15

Bits 15-17: SMP15.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP16

Bits 18-20: SMP16.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP17

Bits 21-23: SMP17.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP18

Bits 24-26: SMP18.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

TR1

watchdog threshold register 1

Offset: 0x20, size: 32, reset: 0x0FFF0000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				HT1 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				LT1 rw

Toggle fields

LT1

Bits 0-11: LT1.

Allowed values: 0x0-0xfff

HT1

Bits 16-27: HT1.

Allowed values: 0x0-0xfff

TR2

watchdog threshold register

Offset: 0x24, size: 32, reset: 0x0FFF0000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								HT2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								LT2 rw

Toggle fields

LT2

Bits 0-7: LT2.

Allowed values: 0x0-0xff

HT2

Bits 16-23: HT2.

Allowed values: 0x0-0xff

TR3

watchdog threshold register 3

Offset: 0x28, size: 32, reset: 0x0FFF0000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								HT3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								LT3 rw

Toggle fields

LT3

Bits 0-7: LT3.

Allowed values: 0x0-0xff

HT3

Bits 16-23: HT3.

Allowed values: 0x0-0xff

SQR1

regular sequence register 1

Offset: 0x30, size: 32, reset: 0x00000000, access: read-write

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
			SQ4 rw						SQ3 rw						SQ2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SQ2 rw					SQ1 rw							L rw

Toggle fields

L

Bits 0-3: L3.

Allowed values: 0x0-0xf

SQ1

Bits 6-10: SQ1.

Allowed values: 0x0-0x13

SQ2

Bits 12-16: SQ2.

Allowed values: 0x0-0x13

SQ3

Bits 18-22: SQ3.

Allowed values: 0x0-0x13

SQ4

Bits 24-28: SQ4.

Allowed values: 0x0-0x13

SQR2

regular sequence register 2

Offset: 0x34, size: 32, reset: 0x00000000, access: read-write

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
			SQ9 rw						SQ8 rw						SQ7 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SQ7 rw					SQ6 rw						SQ5 rw

Toggle fields

SQ5

Bits 0-4: SQ5.

Allowed values: 0x0-0x13

SQ6

Bits 6-10: SQ6.

Allowed values: 0x0-0x13

SQ7

Bits 12-16: SQ7.

Allowed values: 0x0-0x13

SQ8

Bits 18-22: SQ8.

Allowed values: 0x0-0x13

SQ9

Bits 24-28: SQ9.

Allowed values: 0x0-0x13

SQR3

regular sequence register 3

Offset: 0x38, size: 32, reset: 0x00000000, access: read-write

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
			SQ14 rw						SQ13 rw						SQ12 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SQ12 rw					SQ11 rw						SQ10 rw

Toggle fields

SQ10

Bits 0-4: SQ10.

Allowed values: 0x0-0x13

SQ11

Bits 6-10: SQ11.

Allowed values: 0x0-0x13

SQ12

Bits 12-16: SQ12.

Allowed values: 0x0-0x13

SQ13

Bits 18-22: SQ13.

Allowed values: 0x0-0x13

SQ14

Bits 24-28: SQ14.

Allowed values: 0x0-0x13

SQR4

regular sequence register 4

Offset: 0x3c, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
					SQ16 rw						SQ15 rw

Toggle fields

SQ15

Bits 0-4: SQ15.

Allowed values: 0x0-0x13

SQ16

Bits 6-10: SQ16.

Allowed values: 0x0-0x13

DR

regular Data Register

Offset: 0x40, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RDATA r

Toggle fields

RDATA

Bits 0-15: Regular data.

JSQR

injected sequence register

Offset: 0x4c, size: 32, reset: 0x00000000, access: read-write

7/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
	JSQ4 rw						JSQ3 rw						JSQ2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
JSQ2 rw			JSQ1 rw					JEXTEN rw		JEXTSEL rw				JL rw

Toggle fields

JL

Bits 0-1: JL.

Allowed values: 0x0-0x3

JEXTSEL

Bits 2-5: JEXTSEL.

Allowed values:
0: TIM1_TRGO: Timer 1 TRGO event
1: TIM1_CC4: Timer 1 CC4 event
2: TIM2_TRGO: Timer 2 TRGO event
3: TIM2_CC1: Timer 2 CC1 event
4: TIM3_CC4: Timer 3 CC4 event
6: EXTI15: EXTI line 15
8: TIM1_TRGO2: Timer 1 TRGO2 event
9: HRTIM_ADCTRG2: HRTIM_ADCTRG2 event
10: HRTIM_ADCTRG4: HRTIM_ADCTRG4 event
11: TIM3_CC3: Timer 3 CC3 event
12: TIM3_TRGO: Timer 3 TRGO event
13: TIM3_CC1: Timer 3 CC1 event
14: TIM6_TRGO: Timer 6 TRGO event
15: TIM15_TRGO: Timer 15 TRGO event

JEXTEN

Bits 6-7: JEXTEN.

Allowed values:
0: Disabled: Trigger detection disabled
1: RisingEdge: Trigger detection on the rising edge
2: FallingEdge: Trigger detection on the falling edge
3: BothEdges: Trigger detection on both the rising and falling edges

JSQ1

Bits 8-12: JSQ1.

Allowed values: 0x0-0x13

JSQ2

Bits 14-18: JSQ2.

Allowed values: 0x0-0x13

JSQ3

Bits 20-24: JSQ3.

Allowed values: 0x0-0x13

JSQ4

Bits 26-30: JSQ4.

Allowed values: 0x0-0x13

OFR1

offset register 1

Offset: 0x60, size: 32, reset: 0x00000000, access: read-write

3/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OFFSET1_EN rw	OFFSET1_CH rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				OFFSET1 rw

Toggle fields

OFFSET1

Bits 0-11: OFFSET1.

Allowed values: 0x0-0xfff

OFFSET1_CH

Bits 26-30: OFFSET1_CH.

Allowed values: 0x0-0x1f

OFFSET1_EN

Bit 31: OFFSET1_EN.

Allowed values:
0: Disabled: Offset disabled
1: Enabled: Offset enabled

OFR2

offset register 2

Offset: 0x64, size: 32, reset: 0x00000000, access: read-write

3/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OFFSET2_EN rw	OFFSET2_CH rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				OFFSET2 rw

Toggle fields

OFFSET2

Bits 0-11: OFFSET2.

Allowed values: 0x0-0xfff

OFFSET2_CH

Bits 26-30: OFFSET2_CH.

Allowed values: 0x0-0x1f

OFFSET2_EN

Bit 31: OFFSET2_EN.

Allowed values:
0: Disabled: Offset disabled
1: Enabled: Offset enabled

OFR3

offset register 3

Offset: 0x68, size: 32, reset: 0x00000000, access: read-write

3/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OFFSET3_EN rw	OFFSET3_CH rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				OFFSET3 rw

Toggle fields

OFFSET3

Bits 0-11: OFFSET3.

Allowed values: 0x0-0xfff

OFFSET3_CH

Bits 26-30: OFFSET3_CH.

Allowed values: 0x0-0x1f

OFFSET3_EN

Bit 31: OFFSET3_EN.

Allowed values:
0: Disabled: Offset disabled
1: Enabled: Offset enabled

OFR4

offset register 4

Offset: 0x6c, size: 32, reset: 0x00000000, access: read-write

3/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OFFSET4_EN rw	OFFSET4_CH rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				OFFSET4 rw

Toggle fields

OFFSET4

Bits 0-11: OFFSET4.

Allowed values: 0x0-0xfff

OFFSET4_CH

Bits 26-30: OFFSET4_CH.

Allowed values: 0x0-0x1f

OFFSET4_EN

Bit 31: OFFSET4_EN.

Allowed values:
0: Disabled: Offset disabled
1: Enabled: Offset enabled

JDR1

injected data register 1

Offset: 0x80, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
JDATA1 r

Toggle fields

JDATA1

Bits 0-15: JDATA1.

JDR2

injected data register 2

Offset: 0x84, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
JDATA2 r

Toggle fields

JDATA2

Bits 0-15: JDATA2.

JDR3

injected data register 3

Offset: 0x88, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
JDATA3 r

Toggle fields

JDATA3

Bits 0-15: JDATA3.

JDR4

injected data register 4

Offset: 0x8c, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
JDATA4 r

Toggle fields

JDATA4

Bits 0-15: JDATA4.

AWD2CR

Analog Watchdog 2 Configuration Register

Offset: 0xa0, size: 32, reset: 0x00000000, access: read-write

18/18 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
													AWD2CH17 rw	AWD2CH16 rw	AWD2CH15 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AWD2CH14 rw	AWD2CH13 rw	AWD2CH12 rw	AWD2CH11 rw	AWD2CH10 rw	AWD2CH9 rw	AWD2CH8 rw	AWD2CH7 rw	AWD2CH6 rw	AWD2CH5 rw	AWD2CH4 rw	AWD2CH3 rw	AWD2CH2 rw	AWD2CH1 rw	AWD2CH0 rw

Toggle fields

AWD2CH0

Bit 1: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH1

Bit 2: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH2

Bit 3: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH3

Bit 4: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH4

Bit 5: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH5

Bit 6: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH6

Bit 7: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH7

Bit 8: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH8

Bit 9: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH9

Bit 10: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH10

Bit 11: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH11

Bit 12: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH12

Bit 13: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH13

Bit 14: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH14

Bit 15: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH15

Bit 16: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH16

Bit 17: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH17

Bit 18: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CR

Analog Watchdog 3 Configuration Register

Offset: 0xa4, size: 32, reset: 0x00000000, access: read-write

18/18 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
													AWD3CH17 rw	AWD3CH16 rw	AWD3CH15 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AWD3CH14 rw	AWD3CH13 rw	AWD3CH12 rw	AWD3CH11 rw	AWD3CH10 rw	AWD3CH9 rw	AWD3CH8 rw	AWD3CH7 rw	AWD3CH6 rw	AWD3CH5 rw	AWD3CH4 rw	AWD3CH3 rw	AWD3CH2 rw	AWD3CH1 rw	AWD3CH0 rw

Toggle fields

AWD3CH0

Bit 1: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH1

Bit 2: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH2

Bit 3: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH3

Bit 4: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH4

Bit 5: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH5

Bit 6: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH6

Bit 7: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH7

Bit 8: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH8

Bit 9: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH9

Bit 10: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH10

Bit 11: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH11

Bit 12: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH12

Bit 13: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH13

Bit 14: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH14

Bit 15: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH15

Bit 16: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH16

Bit 17: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH17

Bit 18: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

DIFSEL

Differential Mode Selection Register 2

Offset: 0xb0, size: 32, reset: 0x00000000, access: Unspecified

18/18 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
													DIFSEL_117 N/A	DIFSEL_116 N/A	DIFSEL_115 N/A
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DIFSEL_114 N/A	DIFSEL_113 N/A	DIFSEL_112 N/A	DIFSEL_111 N/A	DIFSEL_110 N/A	DIFSEL_19 N/A	DIFSEL_18 N/A	DIFSEL_17 N/A	DIFSEL_16 N/A	DIFSEL_15 N/A	DIFSEL_14 N/A	DIFSEL_13 N/A	DIFSEL_12 N/A	DIFSEL_11 N/A	DIFSEL_10 N/A

Toggle fields

DIFSEL_10

Bit 1: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_11

Bit 2: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_12

Bit 3: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_13

Bit 4: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_14

Bit 5: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_15

Bit 6: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_16

Bit 7: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_17

Bit 8: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_18

Bit 9: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_19

Bit 10: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_110

Bit 11: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_111

Bit 12: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_112

Bit 13: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_113

Bit 14: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_114

Bit 15: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_115

Bit 16: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_116

Bit 17: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_117

Bit 18: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

CALFACT

Calibration Factors

Offset: 0xb4, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
									CALFACT_D rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
									CALFACT_S rw

Toggle fields

CALFACT_S

Bits 0-6: CALFACT_S.

Allowed values: 0x0-0x7f

CALFACT_D

Bits 16-22: CALFACT_D.

Allowed values: 0x0-0x7f

ADC1_2

0x50000300: Analog-to-Digital Converter

32/32 fields covered.

Toggle register map

Offset	Name	31	26	25	24	23	22	21	20	19	18	17	16	15	13	11	10	9	8	7	6	5	4	3	2	1	0
0x0	CSR		JQOVF_SLV	AWD3_SLV	AWD2_SLV	AWD1_SLV	JEOS_SLV	JEOC_SLV	OVR_SLV	EOS_SLV	EOC_SLV	EOSMP_SLV	ADRDY_SLV				JQOVF_MST	AWD3_MST	AWD2_MST	AWD1_MST	JEOS_MST	JEOC_MST	OVR_MST	EOS_MST	EOC_MST	EOSMP_MST	ADDRDY_MST
0x8	CCR				VBATEN	TSEN	VREFEN					CKMODE		MDMA	DMACFG	DELAY							DUAL
0xc	CDR	RDATA_SLV												RDATA_MST

Toggle registers

CSR

ADC Common status register

Offset: 0x0, size: 32, reset: 0x00000000, access: read-only

22/22 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
					JQOVF_SLV r	AWD3_SLV r	AWD2_SLV r	AWD1_SLV r	JEOS_SLV r	JEOC_SLV r	OVR_SLV r	EOS_SLV r	EOC_SLV r	EOSMP_SLV r	ADRDY_SLV r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
					JQOVF_MST r	AWD3_MST r	AWD2_MST r	AWD1_MST r	JEOS_MST r	JEOC_MST r	OVR_MST r	EOS_MST r	EOC_MST r	EOSMP_MST r	ADDRDY_MST r

Toggle fields

ADDRDY_MST

Bit 0: ADDRDY_MST.

EOSMP_MST

Bit 1: EOSMP_MST.

Allowed values:
0: NotEnded: End of sampling phase no yet reached
1: Ended: End of sampling phase reached

EOC_MST

Bit 2: EOC_MST.

Allowed values:
0: NotComplete: Regular conversion is not complete
1: Complete: Regular conversion complete

EOS_MST

Bit 3: EOS_MST.

Allowed values:
0: NotComplete: Regular sequence is not complete
1: Complete: Regular sequence complete

OVR_MST

Bit 4: OVR_MST.

Allowed values:
0: NoOverrun: No overrun occurred
1: Overrun: Overrun occurred

JEOC_MST

Bit 5: JEOC_MST.

Allowed values:
0: NotComplete: Injected conversion is not complete
1: Complete: Injected conversion complete

JEOS_MST

Bit 6: JEOS_MST.

Allowed values:
0: NotComplete: Injected sequence is not complete
1: Complete: Injected sequence complete

AWD1_MST

Bit 7: AWD1_MST.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

AWD2_MST

Bit 8: AWD2_MST.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

AWD3_MST

Bit 9: AWD3_MST.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

JQOVF_MST

Bit 10: JQOVF_MST.

Allowed values:
0: NoOverflow: No injected context queue overflow has occurred
1: Overflow: Injected context queue overflow has occurred

ADRDY_SLV

Bit 16: ADRDY_SLV.

Allowed values:
0: NotReady: ADC is not ready to start conversion
1: Ready: ADC is ready to start conversion

EOSMP_SLV

Bit 17: EOSMP_SLV.

Allowed values:
0: NotEnded: End of sampling phase no yet reached
1: Ended: End of sampling phase reached

EOC_SLV

Bit 18: End of regular conversion of the slave ADC.

Allowed values:
0: NotComplete: Regular conversion is not complete
1: Complete: Regular conversion complete

EOS_SLV

Bit 19: End of regular sequence flag of the slave ADC.

Allowed values:
0: NotComplete: Regular sequence is not complete
1: Complete: Regular sequence complete

OVR_SLV

Bit 20: Overrun flag of the slave ADC.

Allowed values:
0: NoOverrun: No overrun occurred
1: Overrun: Overrun occurred

JEOC_SLV

Bit 21: End of injected conversion flag of the slave ADC.

Allowed values:
0: NotComplete: Injected conversion is not complete
1: Complete: Injected conversion complete

JEOS_SLV

Bit 22: End of injected sequence flag of the slave ADC.

Allowed values:
0: NotComplete: Injected sequence is not complete
1: Complete: Injected sequence complete

AWD1_SLV

Bit 23: Analog watchdog 1 flag of the slave ADC.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

AWD2_SLV

Bit 24: Analog watchdog 2 flag of the slave ADC.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

AWD3_SLV

Bit 25: Analog watchdog 3 flag of the slave ADC.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

JQOVF_SLV

Bit 26: Injected Context Queue Overflow flag of the slave ADC.

Allowed values:
0: NoOverflow: No injected context queue overflow has occurred
1: Overflow: Injected context queue overflow has occurred

CCR

ADC common control register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
							VBATEN rw	TSEN rw	VREFEN rw					CKMODE rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MDMA rw		DMACFG rw		DELAY rw							DUAL rw

Toggle fields

DUAL

Bits 0-4: Dual ADC mode selection.

Allowed values:
0: Independent: Independent mode
1: DualRJ: Dual, combined regular simultaneous + injected simultaneous mode
2: DualRA: Dual, combined regular simultaneous + alternate trigger mode
3: DualIJ: Dual, combined interleaved mode + injected simultaneous mode
5: DualJ: Dual, injected simultaneous mode only
6: DualR: Dual, regular simultaneous mode only
7: DualI: Dual, interleaved mode only
9: DualA: Dual, alternate trigger mode only

DELAY

Bits 8-11: Delay between 2 sampling phases.

Allowed values: 0x0-0xf

DMACFG

Bit 13: DMA configuration (for multi-ADC mode).

Allowed values:
0: OneShot: DMA one shot mode selected
1: Circulator: DMA circular mode selected

MDMA

Bits 14-15: Direct memory access mode for multi ADC mode.

Allowed values:
0: Disabled: MDMA mode disabled
2: Bits12_10: MDMA mode enabled for 12 and 10-bit resolution
3: Bits8_6: MDMA mode enabled for 8 and 6-bit resolution

CKMODE

Bits 16-17: ADC clock mode.

Allowed values:
0: Asynchronous: Use Kernel Clock adc_ker_ck_input divided by PRESC. Asynchronous to AHB clock
1: SyncDiv1: Use AHB clock rcc_hclk3. In this case rcc_hclk must equal sys_d1cpre_ck
2: SyncDiv2: Use AHB clock rcc_hclk3 divided by 2
3: SyncDiv4: Use AHB clock rcc_hclk3 divided by 4

VREFEN

Bit 22: VREFINT enable.

Allowed values:
0: Disabled: V_REFINT channel disabled
1: Enabled: V_REFINT channel enabled

TSEN

Bit 23: Temperature sensor enable.

Allowed values:
0: Disabled: Temperature sensor channel disabled
1: Enabled: Temperature sensor channel enabled

VBATEN

Bit 24: VBAT enable.

Allowed values:
0: Disabled: V_BAT channel disabled
1: Enabled: V_BAT channel enabled

CDR

ADC common regular data register for dual and triple modes

Offset: 0xc, size: 32, reset: 0x00000000, access: read-only

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
RDATA_SLV r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RDATA_MST r

Toggle fields

RDATA_MST

Bits 0-15: Regular data of the master ADC.

RDATA_SLV

Bits 16-31: Regular data of the slave ADC.

ADC2

0x50000100: Analog-to-Digital Converter

170/170 fields covered.

Toggle register map

Offset	Name	31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	ISR																						JQOVF	AWD3	AWD2	AWD1	JEOS	JEOC	OVR	EOS	EOC	EOSMP	ADRDY
0x4	IER																						JQOVFIE	AWD3IE	AWD2IE	AWD1IE	JEOSIE	JEOCIE	OVRIE	EOSIE	EOCIE	EOSMPIE	ADRDYIE
0x8	CR	ADCAL	ADCALDIF	ADVREGEN																								JADSTP	ADSTP	JADSTART	ADSTART	ADDIS	ADEN
0xc	CFGR		AWD1CH					JAUTO	JAWD1EN	AWD1EN	AWD1SGL	JQM	JDISCEN	DISCNUM			DISCEN		AUTDLY	CONT	OVRMOD	EXTEN		EXTSEL				ALIGN	RES			DMACFG	DMAEN
0x14	SMPR1			SMP9			SMP8			SMP7			SMP6			SMP5		SMP5	SMP4			SMP3			SMP2			SMP1
0x18	SMPR2						SMP18			SMP17			SMP16			SMP15		SMP15	SMP14			SMP13			SMP12			SMP11			SMP10
0x20	TR1					HT1																LT1
0x24	TR2									HT2																LT2
0x28	TR3									HT3																LT3
0x30	SQR1				SQ4						SQ3						SQ2	SQ2					SQ1							L
0x34	SQR2				SQ9						SQ8						SQ7	SQ7					SQ6						SQ5
0x38	SQR3				SQ14						SQ13						SQ12	SQ12					SQ11						SQ10
0x3c	SQR4																						SQ16						SQ15
0x40	DR																	RDATA
0x4c	JSQR		JSQ4						JSQ3						JSQ2			JSQ2			JSQ1					JEXTEN		JEXTSEL				JL
0x60	OFR1	OFFSET1_EN	OFFSET1_CH																			OFFSET1
0x64	OFR2	OFFSET2_EN	OFFSET2_CH																			OFFSET2
0x68	OFR3	OFFSET3_EN	OFFSET3_CH																			OFFSET3
0x6c	OFR4	OFFSET4_EN	OFFSET4_CH																			OFFSET4
0x80	JDR1																	JDATA1
0x84	JDR2																	JDATA2
0x88	JDR3																	JDATA3
0x8c	JDR4																	JDATA4
0xa0	AWD2CR														AWD2CH17	AWD2CH16	AWD2CH15	AWD2CH14	AWD2CH13	AWD2CH12	AWD2CH11	AWD2CH10	AWD2CH9	AWD2CH8	AWD2CH7	AWD2CH6	AWD2CH5	AWD2CH4	AWD2CH3	AWD2CH2	AWD2CH1	AWD2CH0
0xa4	AWD3CR														AWD3CH17	AWD3CH16	AWD3CH15	AWD3CH14	AWD3CH13	AWD3CH12	AWD3CH11	AWD3CH10	AWD3CH9	AWD3CH8	AWD3CH7	AWD3CH6	AWD3CH5	AWD3CH4	AWD3CH3	AWD3CH2	AWD3CH1	AWD3CH0
0xb0	DIFSEL														DIFSEL_117	DIFSEL_116	DIFSEL_115	DIFSEL_114	DIFSEL_113	DIFSEL_112	DIFSEL_111	DIFSEL_110	DIFSEL_19	DIFSEL_18	DIFSEL_17	DIFSEL_16	DIFSEL_15	DIFSEL_14	DIFSEL_13	DIFSEL_12	DIFSEL_11	DIFSEL_10
0xb4	CALFACT										CALFACT_D																CALFACT_S

Toggle registers

ISR

interrupt and status register

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

11/11 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
					JQOVF rw	AWD3 rw	AWD2 rw	AWD1 rw	JEOS rw	JEOC rw	OVR rw	EOS rw	EOC rw	EOSMP rw	ADRDY rw

Toggle fields

ADRDY

Bit 0: ADRDY.

Allowed values:
0: NotReady: ADC is not ready to start conversion
1: Ready: ADC is ready to start conversion

EOSMP

Bit 1: EOSMP.

Allowed values:
0: NotEnded: End of sampling phase no yet reached
1: Ended: End of sampling phase reached

EOC

Bit 2: EOC.

Allowed values:
0: NotComplete: Regular conversion is not complete
1: Complete: Regular conversion complete

EOS

Bit 3: EOS.

Allowed values:
0: NotComplete: Regular sequence is not complete
1: Complete: Regular sequence complete

OVR

Bit 4: OVR.

Allowed values:
0: NoOverrun: No overrun occurred
1: Overrun: Overrun occurred

JEOC

Bit 5: JEOC.

Allowed values:
0: NotComplete: Injected conversion is not complete
1: Complete: Injected conversion complete

JEOS

Bit 6: JEOS.

Allowed values:
0: NotComplete: Injected sequence is not complete
1: Complete: Injected sequence complete

AWD1

Bit 7: AWD1.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

AWD2

Bit 8: AWD2.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

AWD3

Bit 9: AWD3.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

JQOVF

Bit 10: JQOVF.

Allowed values:
0: NoOverflow: No injected context queue overflow has occurred
1: Overflow: Injected context queue overflow has occurred

IER

interrupt enable register

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

11/11 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
					JQOVFIE rw	AWD3IE rw	AWD2IE rw	AWD1IE rw	JEOSIE rw	JEOCIE rw	OVRIE rw	EOSIE rw	EOCIE rw	EOSMPIE rw	ADRDYIE rw

Toggle fields

ADRDYIE

Bit 0: ADRDYIE.

Allowed values:
0: Disabled: ADC ready interrupt disabled
1: Enabled: ADC ready interrupt enabled

EOSMPIE

Bit 1: EOSMPIE.

Allowed values:
0: Disabled: End of regular conversion sampling phase interrupt disabled
1: Enabled: End of regular conversion sampling phase interrupt enabled

EOCIE

Bit 2: EOCIE.

Allowed values:
0: Disabled: End of regular conversion interrupt disabled
1: Enabled: End of regular conversion interrupt enabled

EOSIE

Bit 3: EOSIE.

Allowed values:
0: Disabled: End of regular sequence interrupt disabled
1: Enabled: End of regular sequence interrupt enabled

OVRIE

Bit 4: OVRIE.

Allowed values:
0: Disabled: Overrun interrupt disabled
1: Enabled: Overrun interrupt enabled

JEOCIE

Bit 5: JEOCIE.

Allowed values:
0: Disabled: End of injected conversion interrupt disabled
1: Enabled: End of injected conversion interrupt enabled

JEOSIE

Bit 6: JEOSIE.

Allowed values:
0: Disabled: End of injected sequence interrupt disabled
1: Enabled: End of injected sequence interrupt enabled

AWD1IE

Bit 7: AWD1IE.

Allowed values:
0: Disabled: Analog watchdog interrupt disabled
1: Enabled: Analog watchdog interrupt enabled

AWD2IE

Bit 8: AWD2IE.

Allowed values:
0: Disabled: Analog watchdog interrupt disabled
1: Enabled: Analog watchdog interrupt enabled

AWD3IE

Bit 9: AWD3IE.

Allowed values:
0: Disabled: Analog watchdog interrupt disabled
1: Enabled: Analog watchdog interrupt enabled

JQOVFIE

Bit 10: JQOVFIE.

Allowed values:
0: Disabled: Injected context queue overflow interrupt disabled
1: Enabled: Injected context queue overflow interrupt enabled

CR

control register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

9/9 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ADCAL rw	ADCALDIF rw	ADVREGEN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
										JADSTP rw	ADSTP rw	JADSTART rw	ADSTART rw	ADDIS rw	ADEN rw

Toggle fields

ADEN

Bit 0: ADEN.

Allowed values:
0: Disabled: ADC disabled
1: Enabled: ADC enabled

ADDIS

Bit 1: ADDIS.

Allowed values:
0: NotDisabling: No disable command active
1: Disabling: ADC disabling

ADSTART

Bit 2: ADSTART.

Allowed values:
0: NotActive: No conversion ongoing
1: Active: ADC operating and may be converting

JADSTART

Bit 3: JADSTART.

Allowed values:
0: NotActive: No conversion ongoing
1: Active: ADC operating and may be converting

ADSTP

Bit 4: ADSTP.

Allowed values:
0: NotStopping: No stop command active
1: Stopping: ADC stopping conversion

JADSTP

Bit 5: JADSTP.

Allowed values:
0: NotStopping: No stop command active
1: Stopping: ADC stopping conversion

ADVREGEN

Bits 28-29: ADVREGEN.

Allowed values:
0: Intermediate: Intermediate state required when moving the ADC voltage regulator between states
1: Enabled: ADC voltage regulator enabled
2: Disabled: ADC voltage regulator disabled

ADCALDIF

Bit 30: ADCALDIF.

Allowed values:
0: SingleEnded: Calibration for single-ended mode
1: Differential: Calibration for differential mode

ADCAL

Bit 31: ADCAL.

Allowed values:
0: Complete: Calibration complete
1: Calibration: Start the calibration of the ADC

CFGR

configuration register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

18/18 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
	AWD1CH rw					JAUTO rw	JAWD1EN rw	AWD1EN rw	AWD1SGL rw	JQM rw	JDISCEN rw	DISCNUM rw			DISCEN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	AUTDLY rw	CONT rw	OVRMOD rw	EXTEN rw		EXTSEL rw				ALIGN rw	RES rw			DMACFG rw	DMAEN rw

Toggle fields

DMAEN

Bit 0: DMAEN.

Allowed values:
0: Disabled: DMA disabled
1: Enabled: DMA enabled

DMACFG

Bit 1: DMACFG.

Allowed values:
0: OneShot: DMA One Shot Mode selected
1: Circular: DMA circular mode selected

RES

Bits 3-4: RES.

Allowed values:
0: Bits12: 12-bit
1: Bits10: 10-bit
2: Bits8: 8-bit
3: Bits6: 6-bit

ALIGN

Bit 5: ALIGN.

Allowed values:
0: Right: Right alignment
1: Left: Left alignment

EXTSEL

Bits 6-9: EXTSEL.

Allowed values:
0: TIM1_CC1: Timer 1 CC1 event
1: TIM1_CC2: Timer 1 CC2 event
2: TIM1_CC3: Timer 1 CC3 event
3: TIM2_CC2: Timer 2 CC2 event
4: TIM3_TRGO: Timer 3 TRGO event
6: EXTI11: EXTI line 11
7: HRTIM_ADCTRG1: HRTIM_ADCTRG1 event
8: HRTIM_ADCTRG3: HRTIM_ADCTRG3 event
9: TIM1_TRGO: Timer 1 TRGO event
10: TIM1_TRGO2: Timer 1 TRGO2 event
11: TIM2_TRGO: Timer 2 TRGO event
13: TIM6_TRGO: Timer 6 TRGO event
14: TIM15_TRGO: Timer 15 TRGO event
15: TIM3_CC4: Timer 3 CC4 event

EXTEN

Bits 10-11: EXTEN.

Allowed values:
0: Disabled: Trigger detection disabled
1: RisingEdge: Trigger detection on the rising edge
2: FallingEdge: Trigger detection on the falling edge
3: BothEdges: Trigger detection on both the rising and falling edges

OVRMOD

Bit 12: OVRMOD.

Allowed values:
0: Preserve: Preserve DR register when an overrun is detected
1: Overwrite: Overwrite DR register when an overrun is detected

CONT

Bit 13: CONT.

Allowed values:
0: Single: Single conversion mode
1: Continuous: Continuous conversion mode

AUTDLY

Bit 14: AUTDLY.

Allowed values:
0: Off: Auto delayed conversion mode off
1: On: Auto delayed conversion mode on

DISCEN

Bit 16: DISCEN.

Allowed values:
0: Disabled: Discontinuous mode on regular channels disabled
1: Enabled: Discontinuous mode on regular channels enabled

DISCNUM

Bits 17-19: DISCNUM.

Allowed values: 0x0-0x7

JDISCEN

Bit 20: JDISCEN.

Allowed values:
0: Disabled: Discontinuous mode on injected channels disabled
1: Enabled: Discontinuous mode on injected channels enabled

JQM

Bit 21: JQM.

Allowed values:
0: Mode0: JSQR Mode 0: Queue maintains the last written configuration into JSQR
1: Mode1: JSQR Mode 1: An empty queue disables software and hardware triggers of the injected sequence

AWD1SGL

Bit 22: AWD1SGL.

Allowed values:
0: All: Analog watchdog 1 enabled on all channels
1: Single: Analog watchdog 1 enabled on single channel selected in AWD1CH

AWD1EN

Bit 23: AWD1EN.

Allowed values:
0: Disabled: Analog watchdog 1 disabled on regular channels
1: Enabled: Analog watchdog 1 enabled on regular channels

JAWD1EN

Bit 24: JAWD1EN.

Allowed values:
0: Disabled: Analog watchdog 1 disabled on injected channels
1: Enabled: Analog watchdog 1 enabled on injected channels

JAUTO

Bit 25: JAUTO.

Allowed values:
0: Disabled: Automatic injected group conversion disabled
1: Enabled: Automatic injected group conversion enabled

AWD1CH

Bits 26-30: AWDCH1CH.

Allowed values: 0x0-0x13

SMPR1

sample time register 1

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

9/9 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
		SMP9 rw			SMP8 rw			SMP7 rw			SMP6 rw			SMP5 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SMP5 rw	SMP4 rw			SMP3 rw			SMP2 rw			SMP1 rw

Toggle fields

SMP1

Bits 3-5: SMP1.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP2

Bits 6-8: SMP2.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP3

Bits 9-11: SMP3.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP4

Bits 12-14: SMP4.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP5

Bits 15-17: SMP5.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP6

Bits 18-20: SMP6.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP7

Bits 21-23: SMP7.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP8

Bits 24-26: SMP8.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP9

Bits 27-29: SMP9.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMPR2

sample time register 2

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

9/9 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
					SMP18 rw			SMP17 rw			SMP16 rw			SMP15 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SMP15 rw	SMP14 rw			SMP13 rw			SMP12 rw			SMP11 rw			SMP10 rw

Toggle fields

SMP10

Bits 0-2: SMP10.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP11

Bits 3-5: SMP11.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP12

Bits 6-8: SMP12.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP13

Bits 9-11: SMP13.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP14

Bits 12-14: SMP14.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP15

Bits 15-17: SMP15.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP16

Bits 18-20: SMP16.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP17

Bits 21-23: SMP17.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP18

Bits 24-26: SMP18.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

TR1

watchdog threshold register 1

Offset: 0x20, size: 32, reset: 0x0FFF0000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				HT1 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				LT1 rw

Toggle fields

LT1

Bits 0-11: LT1.

Allowed values: 0x0-0xfff

HT1

Bits 16-27: HT1.

Allowed values: 0x0-0xfff

TR2

watchdog threshold register

Offset: 0x24, size: 32, reset: 0x0FFF0000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								HT2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								LT2 rw

Toggle fields

LT2

Bits 0-7: LT2.

Allowed values: 0x0-0xff

HT2

Bits 16-23: HT2.

Allowed values: 0x0-0xff

TR3

watchdog threshold register 3

Offset: 0x28, size: 32, reset: 0x0FFF0000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								HT3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								LT3 rw

Toggle fields

LT3

Bits 0-7: LT3.

Allowed values: 0x0-0xff

HT3

Bits 16-23: HT3.

Allowed values: 0x0-0xff

SQR1

regular sequence register 1

Offset: 0x30, size: 32, reset: 0x00000000, access: read-write

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
			SQ4 rw						SQ3 rw						SQ2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SQ2 rw					SQ1 rw							L rw

Toggle fields

L

Bits 0-3: L3.

Allowed values: 0x0-0xf

SQ1

Bits 6-10: SQ1.

Allowed values: 0x0-0x13

SQ2

Bits 12-16: SQ2.

Allowed values: 0x0-0x13

SQ3

Bits 18-22: SQ3.

Allowed values: 0x0-0x13

SQ4

Bits 24-28: SQ4.

Allowed values: 0x0-0x13

SQR2

regular sequence register 2

Offset: 0x34, size: 32, reset: 0x00000000, access: read-write

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
			SQ9 rw						SQ8 rw						SQ7 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SQ7 rw					SQ6 rw						SQ5 rw

Toggle fields

SQ5

Bits 0-4: SQ5.

Allowed values: 0x0-0x13

SQ6

Bits 6-10: SQ6.

Allowed values: 0x0-0x13

SQ7

Bits 12-16: SQ7.

Allowed values: 0x0-0x13

SQ8

Bits 18-22: SQ8.

Allowed values: 0x0-0x13

SQ9

Bits 24-28: SQ9.

Allowed values: 0x0-0x13

SQR3

regular sequence register 3

Offset: 0x38, size: 32, reset: 0x00000000, access: read-write

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
			SQ14 rw						SQ13 rw						SQ12 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SQ12 rw					SQ11 rw						SQ10 rw

Toggle fields

SQ10

Bits 0-4: SQ10.

Allowed values: 0x0-0x13

SQ11

Bits 6-10: SQ11.

Allowed values: 0x0-0x13

SQ12

Bits 12-16: SQ12.

Allowed values: 0x0-0x13

SQ13

Bits 18-22: SQ13.

Allowed values: 0x0-0x13

SQ14

Bits 24-28: SQ14.

Allowed values: 0x0-0x13

SQR4

regular sequence register 4

Offset: 0x3c, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
					SQ16 rw						SQ15 rw

Toggle fields

SQ15

Bits 0-4: SQ15.

Allowed values: 0x0-0x13

SQ16

Bits 6-10: SQ16.

Allowed values: 0x0-0x13

DR

regular Data Register

Offset: 0x40, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RDATA r

Toggle fields

RDATA

Bits 0-15: Regular data.

JSQR

injected sequence register

Offset: 0x4c, size: 32, reset: 0x00000000, access: read-write

7/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
	JSQ4 rw						JSQ3 rw						JSQ2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
JSQ2 rw			JSQ1 rw					JEXTEN rw		JEXTSEL rw				JL rw

Toggle fields

JL

Bits 0-1: JL.

Allowed values: 0x0-0x3

JEXTSEL

Bits 2-5: JEXTSEL.

Allowed values:
0: TIM1_TRGO: Timer 1 TRGO event
1: TIM1_CC4: Timer 1 CC4 event
2: TIM2_TRGO: Timer 2 TRGO event
3: TIM2_CC1: Timer 2 CC1 event
4: TIM3_CC4: Timer 3 CC4 event
6: EXTI15: EXTI line 15
8: TIM1_TRGO2: Timer 1 TRGO2 event
9: HRTIM_ADCTRG2: HRTIM_ADCTRG2 event
10: HRTIM_ADCTRG4: HRTIM_ADCTRG4 event
11: TIM3_CC3: Timer 3 CC3 event
12: TIM3_TRGO: Timer 3 TRGO event
13: TIM3_CC1: Timer 3 CC1 event
14: TIM6_TRGO: Timer 6 TRGO event
15: TIM15_TRGO: Timer 15 TRGO event

JEXTEN

Bits 6-7: JEXTEN.

Allowed values:
0: Disabled: Trigger detection disabled
1: RisingEdge: Trigger detection on the rising edge
2: FallingEdge: Trigger detection on the falling edge
3: BothEdges: Trigger detection on both the rising and falling edges

JSQ1

Bits 8-12: JSQ1.

Allowed values: 0x0-0x13

JSQ2

Bits 14-18: JSQ2.

Allowed values: 0x0-0x13

JSQ3

Bits 20-24: JSQ3.

Allowed values: 0x0-0x13

JSQ4

Bits 26-30: JSQ4.

Allowed values: 0x0-0x13

OFR1

offset register 1

Offset: 0x60, size: 32, reset: 0x00000000, access: read-write

3/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OFFSET1_EN rw	OFFSET1_CH rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				OFFSET1 rw

Toggle fields

OFFSET1

Bits 0-11: OFFSET1.

Allowed values: 0x0-0xfff

OFFSET1_CH

Bits 26-30: OFFSET1_CH.

Allowed values: 0x0-0x1f

OFFSET1_EN

Bit 31: OFFSET1_EN.

Allowed values:
0: Disabled: Offset disabled
1: Enabled: Offset enabled

OFR2

offset register 2

Offset: 0x64, size: 32, reset: 0x00000000, access: read-write

3/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OFFSET2_EN rw	OFFSET2_CH rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				OFFSET2 rw

Toggle fields

OFFSET2

Bits 0-11: OFFSET2.

Allowed values: 0x0-0xfff

OFFSET2_CH

Bits 26-30: OFFSET2_CH.

Allowed values: 0x0-0x1f

OFFSET2_EN

Bit 31: OFFSET2_EN.

Allowed values:
0: Disabled: Offset disabled
1: Enabled: Offset enabled

OFR3

offset register 3

Offset: 0x68, size: 32, reset: 0x00000000, access: read-write

3/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OFFSET3_EN rw	OFFSET3_CH rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				OFFSET3 rw

Toggle fields

OFFSET3

Bits 0-11: OFFSET3.

Allowed values: 0x0-0xfff

OFFSET3_CH

Bits 26-30: OFFSET3_CH.

Allowed values: 0x0-0x1f

OFFSET3_EN

Bit 31: OFFSET3_EN.

Allowed values:
0: Disabled: Offset disabled
1: Enabled: Offset enabled

OFR4

offset register 4

Offset: 0x6c, size: 32, reset: 0x00000000, access: read-write

3/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OFFSET4_EN rw	OFFSET4_CH rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				OFFSET4 rw

Toggle fields

OFFSET4

Bits 0-11: OFFSET4.

Allowed values: 0x0-0xfff

OFFSET4_CH

Bits 26-30: OFFSET4_CH.

Allowed values: 0x0-0x1f

OFFSET4_EN

Bit 31: OFFSET4_EN.

Allowed values:
0: Disabled: Offset disabled
1: Enabled: Offset enabled

JDR1

injected data register 1

Offset: 0x80, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
JDATA1 r

Toggle fields

JDATA1

Bits 0-15: JDATA1.

JDR2

injected data register 2

Offset: 0x84, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
JDATA2 r

Toggle fields

JDATA2

Bits 0-15: JDATA2.

JDR3

injected data register 3

Offset: 0x88, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
JDATA3 r

Toggle fields

JDATA3

Bits 0-15: JDATA3.

JDR4

injected data register 4

Offset: 0x8c, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
JDATA4 r

Toggle fields

JDATA4

Bits 0-15: JDATA4.

AWD2CR

Analog Watchdog 2 Configuration Register

Offset: 0xa0, size: 32, reset: 0x00000000, access: read-write

18/18 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
													AWD2CH17 rw	AWD2CH16 rw	AWD2CH15 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AWD2CH14 rw	AWD2CH13 rw	AWD2CH12 rw	AWD2CH11 rw	AWD2CH10 rw	AWD2CH9 rw	AWD2CH8 rw	AWD2CH7 rw	AWD2CH6 rw	AWD2CH5 rw	AWD2CH4 rw	AWD2CH3 rw	AWD2CH2 rw	AWD2CH1 rw	AWD2CH0 rw

Toggle fields

AWD2CH0

Bit 1: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH1

Bit 2: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH2

Bit 3: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH3

Bit 4: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH4

Bit 5: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH5

Bit 6: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH6

Bit 7: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH7

Bit 8: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH8

Bit 9: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH9

Bit 10: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH10

Bit 11: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH11

Bit 12: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH12

Bit 13: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH13

Bit 14: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH14

Bit 15: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH15

Bit 16: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH16

Bit 17: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH17

Bit 18: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CR

Analog Watchdog 3 Configuration Register

Offset: 0xa4, size: 32, reset: 0x00000000, access: read-write

18/18 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
													AWD3CH17 rw	AWD3CH16 rw	AWD3CH15 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AWD3CH14 rw	AWD3CH13 rw	AWD3CH12 rw	AWD3CH11 rw	AWD3CH10 rw	AWD3CH9 rw	AWD3CH8 rw	AWD3CH7 rw	AWD3CH6 rw	AWD3CH5 rw	AWD3CH4 rw	AWD3CH3 rw	AWD3CH2 rw	AWD3CH1 rw	AWD3CH0 rw

Toggle fields

AWD3CH0

Bit 1: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH1

Bit 2: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH2

Bit 3: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH3

Bit 4: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH4

Bit 5: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH5

Bit 6: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH6

Bit 7: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH7

Bit 8: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH8

Bit 9: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH9

Bit 10: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH10

Bit 11: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH11

Bit 12: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH12

Bit 13: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH13

Bit 14: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH14

Bit 15: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH15

Bit 16: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH16

Bit 17: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH17

Bit 18: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

DIFSEL

Differential Mode Selection Register 2

Offset: 0xb0, size: 32, reset: 0x00000000, access: Unspecified

18/18 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
													DIFSEL_117 N/A	DIFSEL_116 N/A	DIFSEL_115 N/A
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DIFSEL_114 N/A	DIFSEL_113 N/A	DIFSEL_112 N/A	DIFSEL_111 N/A	DIFSEL_110 N/A	DIFSEL_19 N/A	DIFSEL_18 N/A	DIFSEL_17 N/A	DIFSEL_16 N/A	DIFSEL_15 N/A	DIFSEL_14 N/A	DIFSEL_13 N/A	DIFSEL_12 N/A	DIFSEL_11 N/A	DIFSEL_10 N/A

Toggle fields

DIFSEL_10

Bit 1: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_11

Bit 2: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_12

Bit 3: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_13

Bit 4: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_14

Bit 5: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_15

Bit 6: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_16

Bit 7: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_17

Bit 8: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_18

Bit 9: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_19

Bit 10: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_110

Bit 11: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_111

Bit 12: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_112

Bit 13: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_113

Bit 14: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_114

Bit 15: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_115

Bit 16: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_116

Bit 17: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_117

Bit 18: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

CALFACT

Calibration Factors

Offset: 0xb4, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
									CALFACT_D rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
									CALFACT_S rw

Toggle fields

CALFACT_S

Bits 0-6: CALFACT_S.

Allowed values: 0x0-0x7f

CALFACT_D

Bits 16-22: CALFACT_D.

Allowed values: 0x0-0x7f

ADC3

0x50000400: Analog-to-Digital Converter

170/170 fields covered.

Toggle register map

Offset	Name	31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	ISR																						JQOVF	AWD3	AWD2	AWD1	JEOS	JEOC	OVR	EOS	EOC	EOSMP	ADRDY
0x4	IER																						JQOVFIE	AWD3IE	AWD2IE	AWD1IE	JEOSIE	JEOCIE	OVRIE	EOSIE	EOCIE	EOSMPIE	ADRDYIE
0x8	CR	ADCAL	ADCALDIF	ADVREGEN																								JADSTP	ADSTP	JADSTART	ADSTART	ADDIS	ADEN
0xc	CFGR		AWD1CH					JAUTO	JAWD1EN	AWD1EN	AWD1SGL	JQM	JDISCEN	DISCNUM			DISCEN		AUTDLY	CONT	OVRMOD	EXTEN		EXTSEL				ALIGN	RES			DMACFG	DMAEN
0x14	SMPR1			SMP9			SMP8			SMP7			SMP6			SMP5		SMP5	SMP4			SMP3			SMP2			SMP1
0x18	SMPR2						SMP18			SMP17			SMP16			SMP15		SMP15	SMP14			SMP13			SMP12			SMP11			SMP10
0x20	TR1					HT1																LT1
0x24	TR2									HT2																LT2
0x28	TR3									HT3																LT3
0x30	SQR1				SQ4						SQ3						SQ2	SQ2					SQ1							L
0x34	SQR2				SQ9						SQ8						SQ7	SQ7					SQ6						SQ5
0x38	SQR3				SQ14						SQ13						SQ12	SQ12					SQ11						SQ10
0x3c	SQR4																						SQ16						SQ15
0x40	DR																	RDATA
0x4c	JSQR		JSQ4						JSQ3						JSQ2			JSQ2			JSQ1					JEXTEN		JEXTSEL				JL
0x60	OFR1	OFFSET1_EN	OFFSET1_CH																			OFFSET1
0x64	OFR2	OFFSET2_EN	OFFSET2_CH																			OFFSET2
0x68	OFR3	OFFSET3_EN	OFFSET3_CH																			OFFSET3
0x6c	OFR4	OFFSET4_EN	OFFSET4_CH																			OFFSET4
0x80	JDR1																	JDATA1
0x84	JDR2																	JDATA2
0x88	JDR3																	JDATA3
0x8c	JDR4																	JDATA4
0xa0	AWD2CR														AWD2CH17	AWD2CH16	AWD2CH15	AWD2CH14	AWD2CH13	AWD2CH12	AWD2CH11	AWD2CH10	AWD2CH9	AWD2CH8	AWD2CH7	AWD2CH6	AWD2CH5	AWD2CH4	AWD2CH3	AWD2CH2	AWD2CH1	AWD2CH0
0xa4	AWD3CR														AWD3CH17	AWD3CH16	AWD3CH15	AWD3CH14	AWD3CH13	AWD3CH12	AWD3CH11	AWD3CH10	AWD3CH9	AWD3CH8	AWD3CH7	AWD3CH6	AWD3CH5	AWD3CH4	AWD3CH3	AWD3CH2	AWD3CH1	AWD3CH0
0xb0	DIFSEL														DIFSEL_117	DIFSEL_116	DIFSEL_115	DIFSEL_114	DIFSEL_113	DIFSEL_112	DIFSEL_111	DIFSEL_110	DIFSEL_19	DIFSEL_18	DIFSEL_17	DIFSEL_16	DIFSEL_15	DIFSEL_14	DIFSEL_13	DIFSEL_12	DIFSEL_11	DIFSEL_10
0xb4	CALFACT										CALFACT_D																CALFACT_S

Toggle registers

ISR

interrupt and status register

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

11/11 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
					JQOVF rw	AWD3 rw	AWD2 rw	AWD1 rw	JEOS rw	JEOC rw	OVR rw	EOS rw	EOC rw	EOSMP rw	ADRDY rw

Toggle fields

ADRDY

Bit 0: ADRDY.

Allowed values:
0: NotReady: ADC is not ready to start conversion
1: Ready: ADC is ready to start conversion

EOSMP

Bit 1: EOSMP.

Allowed values:
0: NotEnded: End of sampling phase no yet reached
1: Ended: End of sampling phase reached

EOC

Bit 2: EOC.

Allowed values:
0: NotComplete: Regular conversion is not complete
1: Complete: Regular conversion complete

EOS

Bit 3: EOS.

Allowed values:
0: NotComplete: Regular sequence is not complete
1: Complete: Regular sequence complete

OVR

Bit 4: OVR.

Allowed values:
0: NoOverrun: No overrun occurred
1: Overrun: Overrun occurred

JEOC

Bit 5: JEOC.

Allowed values:
0: NotComplete: Injected conversion is not complete
1: Complete: Injected conversion complete

JEOS

Bit 6: JEOS.

Allowed values:
0: NotComplete: Injected sequence is not complete
1: Complete: Injected sequence complete

AWD1

Bit 7: AWD1.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

AWD2

Bit 8: AWD2.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

AWD3

Bit 9: AWD3.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

JQOVF

Bit 10: JQOVF.

Allowed values:
0: NoOverflow: No injected context queue overflow has occurred
1: Overflow: Injected context queue overflow has occurred

IER

interrupt enable register

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

11/11 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
					JQOVFIE rw	AWD3IE rw	AWD2IE rw	AWD1IE rw	JEOSIE rw	JEOCIE rw	OVRIE rw	EOSIE rw	EOCIE rw	EOSMPIE rw	ADRDYIE rw

Toggle fields

ADRDYIE

Bit 0: ADRDYIE.

Allowed values:
0: Disabled: ADC ready interrupt disabled
1: Enabled: ADC ready interrupt enabled

EOSMPIE

Bit 1: EOSMPIE.

Allowed values:
0: Disabled: End of regular conversion sampling phase interrupt disabled
1: Enabled: End of regular conversion sampling phase interrupt enabled

EOCIE

Bit 2: EOCIE.

Allowed values:
0: Disabled: End of regular conversion interrupt disabled
1: Enabled: End of regular conversion interrupt enabled

EOSIE

Bit 3: EOSIE.

Allowed values:
0: Disabled: End of regular sequence interrupt disabled
1: Enabled: End of regular sequence interrupt enabled

OVRIE

Bit 4: OVRIE.

Allowed values:
0: Disabled: Overrun interrupt disabled
1: Enabled: Overrun interrupt enabled

JEOCIE

Bit 5: JEOCIE.

Allowed values:
0: Disabled: End of injected conversion interrupt disabled
1: Enabled: End of injected conversion interrupt enabled

JEOSIE

Bit 6: JEOSIE.

Allowed values:
0: Disabled: End of injected sequence interrupt disabled
1: Enabled: End of injected sequence interrupt enabled

AWD1IE

Bit 7: AWD1IE.

Allowed values:
0: Disabled: Analog watchdog interrupt disabled
1: Enabled: Analog watchdog interrupt enabled

AWD2IE

Bit 8: AWD2IE.

Allowed values:
0: Disabled: Analog watchdog interrupt disabled
1: Enabled: Analog watchdog interrupt enabled

AWD3IE

Bit 9: AWD3IE.

Allowed values:
0: Disabled: Analog watchdog interrupt disabled
1: Enabled: Analog watchdog interrupt enabled

JQOVFIE

Bit 10: JQOVFIE.

Allowed values:
0: Disabled: Injected context queue overflow interrupt disabled
1: Enabled: Injected context queue overflow interrupt enabled

CR

control register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

9/9 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ADCAL rw	ADCALDIF rw	ADVREGEN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
										JADSTP rw	ADSTP rw	JADSTART rw	ADSTART rw	ADDIS rw	ADEN rw

Toggle fields

ADEN

Bit 0: ADEN.

Allowed values:
0: Disabled: ADC disabled
1: Enabled: ADC enabled

ADDIS

Bit 1: ADDIS.

Allowed values:
0: NotDisabling: No disable command active
1: Disabling: ADC disabling

ADSTART

Bit 2: ADSTART.

Allowed values:
0: NotActive: No conversion ongoing
1: Active: ADC operating and may be converting

JADSTART

Bit 3: JADSTART.

Allowed values:
0: NotActive: No conversion ongoing
1: Active: ADC operating and may be converting

ADSTP

Bit 4: ADSTP.

Allowed values:
0: NotStopping: No stop command active
1: Stopping: ADC stopping conversion

JADSTP

Bit 5: JADSTP.

Allowed values:
0: NotStopping: No stop command active
1: Stopping: ADC stopping conversion

ADVREGEN

Bits 28-29: ADVREGEN.

Allowed values:
0: Intermediate: Intermediate state required when moving the ADC voltage regulator between states
1: Enabled: ADC voltage regulator enabled
2: Disabled: ADC voltage regulator disabled

ADCALDIF

Bit 30: ADCALDIF.

Allowed values:
0: SingleEnded: Calibration for single-ended mode
1: Differential: Calibration for differential mode

ADCAL

Bit 31: ADCAL.

Allowed values:
0: Complete: Calibration complete
1: Calibration: Start the calibration of the ADC

CFGR

configuration register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

18/18 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
	AWD1CH rw					JAUTO rw	JAWD1EN rw	AWD1EN rw	AWD1SGL rw	JQM rw	JDISCEN rw	DISCNUM rw			DISCEN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	AUTDLY rw	CONT rw	OVRMOD rw	EXTEN rw		EXTSEL rw				ALIGN rw	RES rw			DMACFG rw	DMAEN rw

Toggle fields

DMAEN

Bit 0: DMAEN.

Allowed values:
0: Disabled: DMA disabled
1: Enabled: DMA enabled

DMACFG

Bit 1: DMACFG.

Allowed values:
0: OneShot: DMA One Shot Mode selected
1: Circular: DMA circular mode selected

RES

Bits 3-4: RES.

Allowed values:
0: Bits12: 12-bit
1: Bits10: 10-bit
2: Bits8: 8-bit
3: Bits6: 6-bit

ALIGN

Bit 5: ALIGN.

Allowed values:
0: Right: Right alignment
1: Left: Left alignment

EXTSEL

Bits 6-9: EXTSEL.

Allowed values:
0: TIM1_CC1: Timer 1 CC1 event
1: TIM1_CC2: Timer 1 CC2 event
2: TIM1_CC3: Timer 1 CC3 event
3: TIM2_CC2: Timer 2 CC2 event
4: TIM3_TRGO: Timer 3 TRGO event
6: EXTI11: EXTI line 11
7: HRTIM_ADCTRG1: HRTIM_ADCTRG1 event
8: HRTIM_ADCTRG3: HRTIM_ADCTRG3 event
9: TIM1_TRGO: Timer 1 TRGO event
10: TIM1_TRGO2: Timer 1 TRGO2 event
11: TIM2_TRGO: Timer 2 TRGO event
13: TIM6_TRGO: Timer 6 TRGO event
14: TIM15_TRGO: Timer 15 TRGO event
15: TIM3_CC4: Timer 3 CC4 event

EXTEN

Bits 10-11: EXTEN.

Allowed values:
0: Disabled: Trigger detection disabled
1: RisingEdge: Trigger detection on the rising edge
2: FallingEdge: Trigger detection on the falling edge
3: BothEdges: Trigger detection on both the rising and falling edges

OVRMOD

Bit 12: OVRMOD.

Allowed values:
0: Preserve: Preserve DR register when an overrun is detected
1: Overwrite: Overwrite DR register when an overrun is detected

CONT

Bit 13: CONT.

Allowed values:
0: Single: Single conversion mode
1: Continuous: Continuous conversion mode

AUTDLY

Bit 14: AUTDLY.

Allowed values:
0: Off: Auto delayed conversion mode off
1: On: Auto delayed conversion mode on

DISCEN

Bit 16: DISCEN.

Allowed values:
0: Disabled: Discontinuous mode on regular channels disabled
1: Enabled: Discontinuous mode on regular channels enabled

DISCNUM

Bits 17-19: DISCNUM.

Allowed values: 0x0-0x7

JDISCEN

Bit 20: JDISCEN.

Allowed values:
0: Disabled: Discontinuous mode on injected channels disabled
1: Enabled: Discontinuous mode on injected channels enabled

JQM

Bit 21: JQM.

Allowed values:
0: Mode0: JSQR Mode 0: Queue maintains the last written configuration into JSQR
1: Mode1: JSQR Mode 1: An empty queue disables software and hardware triggers of the injected sequence

AWD1SGL

Bit 22: AWD1SGL.

Allowed values:
0: All: Analog watchdog 1 enabled on all channels
1: Single: Analog watchdog 1 enabled on single channel selected in AWD1CH

AWD1EN

Bit 23: AWD1EN.

Allowed values:
0: Disabled: Analog watchdog 1 disabled on regular channels
1: Enabled: Analog watchdog 1 enabled on regular channels

JAWD1EN

Bit 24: JAWD1EN.

Allowed values:
0: Disabled: Analog watchdog 1 disabled on injected channels
1: Enabled: Analog watchdog 1 enabled on injected channels

JAUTO

Bit 25: JAUTO.

Allowed values:
0: Disabled: Automatic injected group conversion disabled
1: Enabled: Automatic injected group conversion enabled

AWD1CH

Bits 26-30: AWDCH1CH.

Allowed values: 0x0-0x13

SMPR1

sample time register 1

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

9/9 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
		SMP9 rw			SMP8 rw			SMP7 rw			SMP6 rw			SMP5 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SMP5 rw	SMP4 rw			SMP3 rw			SMP2 rw			SMP1 rw

Toggle fields

SMP1

Bits 3-5: SMP1.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP2

Bits 6-8: SMP2.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP3

Bits 9-11: SMP3.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP4

Bits 12-14: SMP4.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP5

Bits 15-17: SMP5.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP6

Bits 18-20: SMP6.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP7

Bits 21-23: SMP7.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP8

Bits 24-26: SMP8.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP9

Bits 27-29: SMP9.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMPR2

sample time register 2

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

9/9 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
					SMP18 rw			SMP17 rw			SMP16 rw			SMP15 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SMP15 rw	SMP14 rw			SMP13 rw			SMP12 rw			SMP11 rw			SMP10 rw

Toggle fields

SMP10

Bits 0-2: SMP10.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP11

Bits 3-5: SMP11.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP12

Bits 6-8: SMP12.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP13

Bits 9-11: SMP13.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP14

Bits 12-14: SMP14.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP15

Bits 15-17: SMP15.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP16

Bits 18-20: SMP16.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP17

Bits 21-23: SMP17.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP18

Bits 24-26: SMP18.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

TR1

watchdog threshold register 1

Offset: 0x20, size: 32, reset: 0x0FFF0000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				HT1 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				LT1 rw

Toggle fields

LT1

Bits 0-11: LT1.

Allowed values: 0x0-0xfff

HT1

Bits 16-27: HT1.

Allowed values: 0x0-0xfff

TR2

watchdog threshold register

Offset: 0x24, size: 32, reset: 0x0FFF0000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								HT2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								LT2 rw

Toggle fields

LT2

Bits 0-7: LT2.

Allowed values: 0x0-0xff

HT2

Bits 16-23: HT2.

Allowed values: 0x0-0xff

TR3

watchdog threshold register 3

Offset: 0x28, size: 32, reset: 0x0FFF0000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								HT3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								LT3 rw

Toggle fields

LT3

Bits 0-7: LT3.

Allowed values: 0x0-0xff

HT3

Bits 16-23: HT3.

Allowed values: 0x0-0xff

SQR1

regular sequence register 1

Offset: 0x30, size: 32, reset: 0x00000000, access: read-write

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
			SQ4 rw						SQ3 rw						SQ2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SQ2 rw					SQ1 rw							L rw

Toggle fields

L

Bits 0-3: L3.

Allowed values: 0x0-0xf

SQ1

Bits 6-10: SQ1.

Allowed values: 0x0-0x13

SQ2

Bits 12-16: SQ2.

Allowed values: 0x0-0x13

SQ3

Bits 18-22: SQ3.

Allowed values: 0x0-0x13

SQ4

Bits 24-28: SQ4.

Allowed values: 0x0-0x13

SQR2

regular sequence register 2

Offset: 0x34, size: 32, reset: 0x00000000, access: read-write

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
			SQ9 rw						SQ8 rw						SQ7 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SQ7 rw					SQ6 rw						SQ5 rw

Toggle fields

SQ5

Bits 0-4: SQ5.

Allowed values: 0x0-0x13

SQ6

Bits 6-10: SQ6.

Allowed values: 0x0-0x13

SQ7

Bits 12-16: SQ7.

Allowed values: 0x0-0x13

SQ8

Bits 18-22: SQ8.

Allowed values: 0x0-0x13

SQ9

Bits 24-28: SQ9.

Allowed values: 0x0-0x13

SQR3

regular sequence register 3

Offset: 0x38, size: 32, reset: 0x00000000, access: read-write

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
			SQ14 rw						SQ13 rw						SQ12 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SQ12 rw					SQ11 rw						SQ10 rw

Toggle fields

SQ10

Bits 0-4: SQ10.

Allowed values: 0x0-0x13

SQ11

Bits 6-10: SQ11.

Allowed values: 0x0-0x13

SQ12

Bits 12-16: SQ12.

Allowed values: 0x0-0x13

SQ13

Bits 18-22: SQ13.

Allowed values: 0x0-0x13

SQ14

Bits 24-28: SQ14.

Allowed values: 0x0-0x13

SQR4

regular sequence register 4

Offset: 0x3c, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
					SQ16 rw						SQ15 rw

Toggle fields

SQ15

Bits 0-4: SQ15.

Allowed values: 0x0-0x13

SQ16

Bits 6-10: SQ16.

Allowed values: 0x0-0x13

DR

regular Data Register

Offset: 0x40, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RDATA r

Toggle fields

RDATA

Bits 0-15: Regular data.

JSQR

injected sequence register

Offset: 0x4c, size: 32, reset: 0x00000000, access: read-write

7/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
	JSQ4 rw						JSQ3 rw						JSQ2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
JSQ2 rw			JSQ1 rw					JEXTEN rw		JEXTSEL rw				JL rw

Toggle fields

JL

Bits 0-1: JL.

Allowed values: 0x0-0x3

JEXTSEL

Bits 2-5: JEXTSEL.

Allowed values:
0: TIM1_TRGO: Timer 1 TRGO event
1: TIM1_CC4: Timer 1 CC4 event
2: TIM2_TRGO: Timer 2 TRGO event
3: TIM2_CC1: Timer 2 CC1 event
4: TIM3_CC4: Timer 3 CC4 event
6: EXTI15: EXTI line 15
8: TIM1_TRGO2: Timer 1 TRGO2 event
9: HRTIM_ADCTRG2: HRTIM_ADCTRG2 event
10: HRTIM_ADCTRG4: HRTIM_ADCTRG4 event
11: TIM3_CC3: Timer 3 CC3 event
12: TIM3_TRGO: Timer 3 TRGO event
13: TIM3_CC1: Timer 3 CC1 event
14: TIM6_TRGO: Timer 6 TRGO event
15: TIM15_TRGO: Timer 15 TRGO event

JEXTEN

Bits 6-7: JEXTEN.

Allowed values:
0: Disabled: Trigger detection disabled
1: RisingEdge: Trigger detection on the rising edge
2: FallingEdge: Trigger detection on the falling edge
3: BothEdges: Trigger detection on both the rising and falling edges

JSQ1

Bits 8-12: JSQ1.

Allowed values: 0x0-0x13

JSQ2

Bits 14-18: JSQ2.

Allowed values: 0x0-0x13

JSQ3

Bits 20-24: JSQ3.

Allowed values: 0x0-0x13

JSQ4

Bits 26-30: JSQ4.

Allowed values: 0x0-0x13

OFR1

offset register 1

Offset: 0x60, size: 32, reset: 0x00000000, access: read-write

3/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OFFSET1_EN rw	OFFSET1_CH rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				OFFSET1 rw

Toggle fields

OFFSET1

Bits 0-11: OFFSET1.

Allowed values: 0x0-0xfff

OFFSET1_CH

Bits 26-30: OFFSET1_CH.

Allowed values: 0x0-0x1f

OFFSET1_EN

Bit 31: OFFSET1_EN.

Allowed values:
0: Disabled: Offset disabled
1: Enabled: Offset enabled

OFR2

offset register 2

Offset: 0x64, size: 32, reset: 0x00000000, access: read-write

3/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OFFSET2_EN rw	OFFSET2_CH rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				OFFSET2 rw

Toggle fields

OFFSET2

Bits 0-11: OFFSET2.

Allowed values: 0x0-0xfff

OFFSET2_CH

Bits 26-30: OFFSET2_CH.

Allowed values: 0x0-0x1f

OFFSET2_EN

Bit 31: OFFSET2_EN.

Allowed values:
0: Disabled: Offset disabled
1: Enabled: Offset enabled

OFR3

offset register 3

Offset: 0x68, size: 32, reset: 0x00000000, access: read-write

3/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OFFSET3_EN rw	OFFSET3_CH rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				OFFSET3 rw

Toggle fields

OFFSET3

Bits 0-11: OFFSET3.

Allowed values: 0x0-0xfff

OFFSET3_CH

Bits 26-30: OFFSET3_CH.

Allowed values: 0x0-0x1f

OFFSET3_EN

Bit 31: OFFSET3_EN.

Allowed values:
0: Disabled: Offset disabled
1: Enabled: Offset enabled

OFR4

offset register 4

Offset: 0x6c, size: 32, reset: 0x00000000, access: read-write

3/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OFFSET4_EN rw	OFFSET4_CH rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				OFFSET4 rw

Toggle fields

OFFSET4

Bits 0-11: OFFSET4.

Allowed values: 0x0-0xfff

OFFSET4_CH

Bits 26-30: OFFSET4_CH.

Allowed values: 0x0-0x1f

OFFSET4_EN

Bit 31: OFFSET4_EN.

Allowed values:
0: Disabled: Offset disabled
1: Enabled: Offset enabled

JDR1

injected data register 1

Offset: 0x80, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
JDATA1 r

Toggle fields

JDATA1

Bits 0-15: JDATA1.

JDR2

injected data register 2

Offset: 0x84, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
JDATA2 r

Toggle fields

JDATA2

Bits 0-15: JDATA2.

JDR3

injected data register 3

Offset: 0x88, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
JDATA3 r

Toggle fields

JDATA3

Bits 0-15: JDATA3.

JDR4

injected data register 4

Offset: 0x8c, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
JDATA4 r

Toggle fields

JDATA4

Bits 0-15: JDATA4.

AWD2CR

Analog Watchdog 2 Configuration Register

Offset: 0xa0, size: 32, reset: 0x00000000, access: read-write

18/18 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
													AWD2CH17 rw	AWD2CH16 rw	AWD2CH15 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AWD2CH14 rw	AWD2CH13 rw	AWD2CH12 rw	AWD2CH11 rw	AWD2CH10 rw	AWD2CH9 rw	AWD2CH8 rw	AWD2CH7 rw	AWD2CH6 rw	AWD2CH5 rw	AWD2CH4 rw	AWD2CH3 rw	AWD2CH2 rw	AWD2CH1 rw	AWD2CH0 rw

Toggle fields

AWD2CH0

Bit 1: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH1

Bit 2: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH2

Bit 3: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH3

Bit 4: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH4

Bit 5: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH5

Bit 6: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH6

Bit 7: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH7

Bit 8: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH8

Bit 9: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH9

Bit 10: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH10

Bit 11: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH11

Bit 12: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH12

Bit 13: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH13

Bit 14: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH14

Bit 15: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH15

Bit 16: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH16

Bit 17: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH17

Bit 18: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CR

Analog Watchdog 3 Configuration Register

Offset: 0xa4, size: 32, reset: 0x00000000, access: read-write

18/18 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
													AWD3CH17 rw	AWD3CH16 rw	AWD3CH15 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AWD3CH14 rw	AWD3CH13 rw	AWD3CH12 rw	AWD3CH11 rw	AWD3CH10 rw	AWD3CH9 rw	AWD3CH8 rw	AWD3CH7 rw	AWD3CH6 rw	AWD3CH5 rw	AWD3CH4 rw	AWD3CH3 rw	AWD3CH2 rw	AWD3CH1 rw	AWD3CH0 rw

Toggle fields

AWD3CH0

Bit 1: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH1

Bit 2: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH2

Bit 3: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH3

Bit 4: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH4

Bit 5: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH5

Bit 6: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH6

Bit 7: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH7

Bit 8: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH8

Bit 9: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH9

Bit 10: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH10

Bit 11: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH11

Bit 12: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH12

Bit 13: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH13

Bit 14: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH14

Bit 15: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH15

Bit 16: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH16

Bit 17: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH17

Bit 18: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

DIFSEL

Differential Mode Selection Register 2

Offset: 0xb0, size: 32, reset: 0x00000000, access: Unspecified

18/18 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
													DIFSEL_117 N/A	DIFSEL_116 N/A	DIFSEL_115 N/A
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DIFSEL_114 N/A	DIFSEL_113 N/A	DIFSEL_112 N/A	DIFSEL_111 N/A	DIFSEL_110 N/A	DIFSEL_19 N/A	DIFSEL_18 N/A	DIFSEL_17 N/A	DIFSEL_16 N/A	DIFSEL_15 N/A	DIFSEL_14 N/A	DIFSEL_13 N/A	DIFSEL_12 N/A	DIFSEL_11 N/A	DIFSEL_10 N/A

Toggle fields

DIFSEL_10

Bit 1: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_11

Bit 2: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_12

Bit 3: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_13

Bit 4: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_14

Bit 5: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_15

Bit 6: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_16

Bit 7: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_17

Bit 8: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_18

Bit 9: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_19

Bit 10: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_110

Bit 11: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_111

Bit 12: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_112

Bit 13: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_113

Bit 14: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_114

Bit 15: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_115

Bit 16: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_116

Bit 17: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_117

Bit 18: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

CALFACT

Calibration Factors

Offset: 0xb4, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
									CALFACT_D rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
									CALFACT_S rw

Toggle fields

CALFACT_S

Bits 0-6: CALFACT_S.

Allowed values: 0x0-0x7f

CALFACT_D

Bits 16-22: CALFACT_D.

Allowed values: 0x0-0x7f

ADC3_4

0x50000700: Analog-to-Digital Converter

32/32 fields covered.

Toggle register map

Offset	Name	31	26	25	24	23	22	21	20	19	18	17	16	15	13	11	10	9	8	7	6	5	4	3	2	1	0
0x0	CSR		JQOVF_SLV	AWD3_SLV	AWD2_SLV	AWD1_SLV	JEOS_SLV	JEOC_SLV	OVR_SLV	EOS_SLV	EOC_SLV	EOSMP_SLV	ADRDY_SLV				JQOVF_MST	AWD3_MST	AWD2_MST	AWD1_MST	JEOS_MST	JEOC_MST	OVR_MST	EOS_MST	EOC_MST	EOSMP_MST	ADDRDY_MST
0x8	CCR				VBATEN	TSEN	VREFEN					CKMODE		MDMA	DMACFG	DELAY							DUAL
0xc	CDR	RDATA_SLV												RDATA_MST

Toggle registers

CSR

ADC Common status register

Offset: 0x0, size: 32, reset: 0x00000000, access: read-only

22/22 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
					JQOVF_SLV r	AWD3_SLV r	AWD2_SLV r	AWD1_SLV r	JEOS_SLV r	JEOC_SLV r	OVR_SLV r	EOS_SLV r	EOC_SLV r	EOSMP_SLV r	ADRDY_SLV r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
					JQOVF_MST r	AWD3_MST r	AWD2_MST r	AWD1_MST r	JEOS_MST r	JEOC_MST r	OVR_MST r	EOS_MST r	EOC_MST r	EOSMP_MST r	ADDRDY_MST r

Toggle fields

ADDRDY_MST

Bit 0: ADDRDY_MST.

EOSMP_MST

Bit 1: EOSMP_MST.

Allowed values:
0: NotEnded: End of sampling phase no yet reached
1: Ended: End of sampling phase reached

EOC_MST

Bit 2: EOC_MST.

Allowed values:
0: NotComplete: Regular conversion is not complete
1: Complete: Regular conversion complete

EOS_MST

Bit 3: EOS_MST.

Allowed values:
0: NotComplete: Regular sequence is not complete
1: Complete: Regular sequence complete

OVR_MST

Bit 4: OVR_MST.

Allowed values:
0: NoOverrun: No overrun occurred
1: Overrun: Overrun occurred

JEOC_MST

Bit 5: JEOC_MST.

Allowed values:
0: NotComplete: Injected conversion is not complete
1: Complete: Injected conversion complete

JEOS_MST

Bit 6: JEOS_MST.

Allowed values:
0: NotComplete: Injected sequence is not complete
1: Complete: Injected sequence complete

AWD1_MST

Bit 7: AWD1_MST.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

AWD2_MST

Bit 8: AWD2_MST.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

AWD3_MST

Bit 9: AWD3_MST.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

JQOVF_MST

Bit 10: JQOVF_MST.

Allowed values:
0: NoOverflow: No injected context queue overflow has occurred
1: Overflow: Injected context queue overflow has occurred

ADRDY_SLV

Bit 16: ADRDY_SLV.

Allowed values:
0: NotReady: ADC is not ready to start conversion
1: Ready: ADC is ready to start conversion

EOSMP_SLV

Bit 17: EOSMP_SLV.

Allowed values:
0: NotEnded: End of sampling phase no yet reached
1: Ended: End of sampling phase reached

EOC_SLV

Bit 18: End of regular conversion of the slave ADC.

Allowed values:
0: NotComplete: Regular conversion is not complete
1: Complete: Regular conversion complete

EOS_SLV

Bit 19: End of regular sequence flag of the slave ADC.

Allowed values:
0: NotComplete: Regular sequence is not complete
1: Complete: Regular sequence complete

OVR_SLV

Bit 20: Overrun flag of the slave ADC.

Allowed values:
0: NoOverrun: No overrun occurred
1: Overrun: Overrun occurred

JEOC_SLV

Bit 21: End of injected conversion flag of the slave ADC.

Allowed values:
0: NotComplete: Injected conversion is not complete
1: Complete: Injected conversion complete

JEOS_SLV

Bit 22: End of injected sequence flag of the slave ADC.

Allowed values:
0: NotComplete: Injected sequence is not complete
1: Complete: Injected sequence complete

AWD1_SLV

Bit 23: Analog watchdog 1 flag of the slave ADC.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

AWD2_SLV

Bit 24: Analog watchdog 2 flag of the slave ADC.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

AWD3_SLV

Bit 25: Analog watchdog 3 flag of the slave ADC.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

JQOVF_SLV

Bit 26: Injected Context Queue Overflow flag of the slave ADC.

Allowed values:
0: NoOverflow: No injected context queue overflow has occurred
1: Overflow: Injected context queue overflow has occurred

CCR

ADC common control register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
							VBATEN rw	TSEN rw	VREFEN rw					CKMODE rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MDMA rw		DMACFG rw		DELAY rw							DUAL rw

Toggle fields

DUAL

Bits 0-4: Dual ADC mode selection.

Allowed values:
0: Independent: Independent mode
1: DualRJ: Dual, combined regular simultaneous + injected simultaneous mode
2: DualRA: Dual, combined regular simultaneous + alternate trigger mode
3: DualIJ: Dual, combined interleaved mode + injected simultaneous mode
5: DualJ: Dual, injected simultaneous mode only
6: DualR: Dual, regular simultaneous mode only
7: DualI: Dual, interleaved mode only
9: DualA: Dual, alternate trigger mode only

DELAY

Bits 8-11: Delay between 2 sampling phases.

Allowed values: 0x0-0xf

DMACFG

Bit 13: DMA configuration (for multi-ADC mode).

Allowed values:
0: OneShot: DMA one shot mode selected
1: Circulator: DMA circular mode selected

MDMA

Bits 14-15: Direct memory access mode for multi ADC mode.

Allowed values:
0: Disabled: MDMA mode disabled
2: Bits12_10: MDMA mode enabled for 12 and 10-bit resolution
3: Bits8_6: MDMA mode enabled for 8 and 6-bit resolution

CKMODE

Bits 16-17: ADC clock mode.

Allowed values:
0: Asynchronous: Use Kernel Clock adc_ker_ck_input divided by PRESC. Asynchronous to AHB clock
1: SyncDiv1: Use AHB clock rcc_hclk3. In this case rcc_hclk must equal sys_d1cpre_ck
2: SyncDiv2: Use AHB clock rcc_hclk3 divided by 2
3: SyncDiv4: Use AHB clock rcc_hclk3 divided by 4

VREFEN

Bit 22: VREFINT enable.

Allowed values:
0: Disabled: V_REFINT channel disabled
1: Enabled: V_REFINT channel enabled

TSEN

Bit 23: Temperature sensor enable.

Allowed values:
0: Disabled: Temperature sensor channel disabled
1: Enabled: Temperature sensor channel enabled

VBATEN

Bit 24: VBAT enable.

Allowed values:
0: Disabled: V_BAT channel disabled
1: Enabled: V_BAT channel enabled

CDR

ADC common regular data register for dual and triple modes

Offset: 0xc, size: 32, reset: 0x00000000, access: read-only

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
RDATA_SLV r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RDATA_MST r

Toggle fields

RDATA_MST

Bits 0-15: Regular data of the master ADC.

RDATA_SLV

Bits 16-31: Regular data of the slave ADC.

ADC4

0x50000500: Analog-to-Digital Converter

170/170 fields covered.

Toggle register map

Offset	Name	31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	ISR																						JQOVF	AWD3	AWD2	AWD1	JEOS	JEOC	OVR	EOS	EOC	EOSMP	ADRDY
0x4	IER																						JQOVFIE	AWD3IE	AWD2IE	AWD1IE	JEOSIE	JEOCIE	OVRIE	EOSIE	EOCIE	EOSMPIE	ADRDYIE
0x8	CR	ADCAL	ADCALDIF	ADVREGEN																								JADSTP	ADSTP	JADSTART	ADSTART	ADDIS	ADEN
0xc	CFGR		AWD1CH					JAUTO	JAWD1EN	AWD1EN	AWD1SGL	JQM	JDISCEN	DISCNUM			DISCEN		AUTDLY	CONT	OVRMOD	EXTEN		EXTSEL				ALIGN	RES			DMACFG	DMAEN
0x14	SMPR1			SMP9			SMP8			SMP7			SMP6			SMP5		SMP5	SMP4			SMP3			SMP2			SMP1
0x18	SMPR2						SMP18			SMP17			SMP16			SMP15		SMP15	SMP14			SMP13			SMP12			SMP11			SMP10
0x20	TR1					HT1																LT1
0x24	TR2									HT2																LT2
0x28	TR3									HT3																LT3
0x30	SQR1				SQ4						SQ3						SQ2	SQ2					SQ1							L
0x34	SQR2				SQ9						SQ8						SQ7	SQ7					SQ6						SQ5
0x38	SQR3				SQ14						SQ13						SQ12	SQ12					SQ11						SQ10
0x3c	SQR4																						SQ16						SQ15
0x40	DR																	RDATA
0x4c	JSQR		JSQ4						JSQ3						JSQ2			JSQ2			JSQ1					JEXTEN		JEXTSEL				JL
0x60	OFR1	OFFSET1_EN	OFFSET1_CH																			OFFSET1
0x64	OFR2	OFFSET2_EN	OFFSET2_CH																			OFFSET2
0x68	OFR3	OFFSET3_EN	OFFSET3_CH																			OFFSET3
0x6c	OFR4	OFFSET4_EN	OFFSET4_CH																			OFFSET4
0x80	JDR1																	JDATA1
0x84	JDR2																	JDATA2
0x88	JDR3																	JDATA3
0x8c	JDR4																	JDATA4
0xa0	AWD2CR														AWD2CH17	AWD2CH16	AWD2CH15	AWD2CH14	AWD2CH13	AWD2CH12	AWD2CH11	AWD2CH10	AWD2CH9	AWD2CH8	AWD2CH7	AWD2CH6	AWD2CH5	AWD2CH4	AWD2CH3	AWD2CH2	AWD2CH1	AWD2CH0
0xa4	AWD3CR														AWD3CH17	AWD3CH16	AWD3CH15	AWD3CH14	AWD3CH13	AWD3CH12	AWD3CH11	AWD3CH10	AWD3CH9	AWD3CH8	AWD3CH7	AWD3CH6	AWD3CH5	AWD3CH4	AWD3CH3	AWD3CH2	AWD3CH1	AWD3CH0
0xb0	DIFSEL														DIFSEL_117	DIFSEL_116	DIFSEL_115	DIFSEL_114	DIFSEL_113	DIFSEL_112	DIFSEL_111	DIFSEL_110	DIFSEL_19	DIFSEL_18	DIFSEL_17	DIFSEL_16	DIFSEL_15	DIFSEL_14	DIFSEL_13	DIFSEL_12	DIFSEL_11	DIFSEL_10
0xb4	CALFACT										CALFACT_D																CALFACT_S

Toggle registers

ISR

interrupt and status register

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

11/11 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
					JQOVF rw	AWD3 rw	AWD2 rw	AWD1 rw	JEOS rw	JEOC rw	OVR rw	EOS rw	EOC rw	EOSMP rw	ADRDY rw

Toggle fields

ADRDY

Bit 0: ADRDY.

Allowed values:
0: NotReady: ADC is not ready to start conversion
1: Ready: ADC is ready to start conversion

EOSMP

Bit 1: EOSMP.

Allowed values:
0: NotEnded: End of sampling phase no yet reached
1: Ended: End of sampling phase reached

EOC

Bit 2: EOC.

Allowed values:
0: NotComplete: Regular conversion is not complete
1: Complete: Regular conversion complete

EOS

Bit 3: EOS.

Allowed values:
0: NotComplete: Regular sequence is not complete
1: Complete: Regular sequence complete

OVR

Bit 4: OVR.

Allowed values:
0: NoOverrun: No overrun occurred
1: Overrun: Overrun occurred

JEOC

Bit 5: JEOC.

Allowed values:
0: NotComplete: Injected conversion is not complete
1: Complete: Injected conversion complete

JEOS

Bit 6: JEOS.

Allowed values:
0: NotComplete: Injected sequence is not complete
1: Complete: Injected sequence complete

AWD1

Bit 7: AWD1.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

AWD2

Bit 8: AWD2.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

AWD3

Bit 9: AWD3.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

JQOVF

Bit 10: JQOVF.

Allowed values:
0: NoOverflow: No injected context queue overflow has occurred
1: Overflow: Injected context queue overflow has occurred

IER

interrupt enable register

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

11/11 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
					JQOVFIE rw	AWD3IE rw	AWD2IE rw	AWD1IE rw	JEOSIE rw	JEOCIE rw	OVRIE rw	EOSIE rw	EOCIE rw	EOSMPIE rw	ADRDYIE rw

Toggle fields

ADRDYIE

Bit 0: ADRDYIE.

Allowed values:
0: Disabled: ADC ready interrupt disabled
1: Enabled: ADC ready interrupt enabled

EOSMPIE

Bit 1: EOSMPIE.

Allowed values:
0: Disabled: End of regular conversion sampling phase interrupt disabled
1: Enabled: End of regular conversion sampling phase interrupt enabled

EOCIE

Bit 2: EOCIE.

Allowed values:
0: Disabled: End of regular conversion interrupt disabled
1: Enabled: End of regular conversion interrupt enabled

EOSIE

Bit 3: EOSIE.

Allowed values:
0: Disabled: End of regular sequence interrupt disabled
1: Enabled: End of regular sequence interrupt enabled

OVRIE

Bit 4: OVRIE.

Allowed values:
0: Disabled: Overrun interrupt disabled
1: Enabled: Overrun interrupt enabled

JEOCIE

Bit 5: JEOCIE.

Allowed values:
0: Disabled: End of injected conversion interrupt disabled
1: Enabled: End of injected conversion interrupt enabled

JEOSIE

Bit 6: JEOSIE.

Allowed values:
0: Disabled: End of injected sequence interrupt disabled
1: Enabled: End of injected sequence interrupt enabled

AWD1IE

Bit 7: AWD1IE.

Allowed values:
0: Disabled: Analog watchdog interrupt disabled
1: Enabled: Analog watchdog interrupt enabled

AWD2IE

Bit 8: AWD2IE.

Allowed values:
0: Disabled: Analog watchdog interrupt disabled
1: Enabled: Analog watchdog interrupt enabled

AWD3IE

Bit 9: AWD3IE.

Allowed values:
0: Disabled: Analog watchdog interrupt disabled
1: Enabled: Analog watchdog interrupt enabled

JQOVFIE

Bit 10: JQOVFIE.

Allowed values:
0: Disabled: Injected context queue overflow interrupt disabled
1: Enabled: Injected context queue overflow interrupt enabled

CR

control register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

9/9 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ADCAL rw	ADCALDIF rw	ADVREGEN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
										JADSTP rw	ADSTP rw	JADSTART rw	ADSTART rw	ADDIS rw	ADEN rw

Toggle fields

ADEN

Bit 0: ADEN.

Allowed values:
0: Disabled: ADC disabled
1: Enabled: ADC enabled

ADDIS

Bit 1: ADDIS.

Allowed values:
0: NotDisabling: No disable command active
1: Disabling: ADC disabling

ADSTART

Bit 2: ADSTART.

Allowed values:
0: NotActive: No conversion ongoing
1: Active: ADC operating and may be converting

JADSTART

Bit 3: JADSTART.

Allowed values:
0: NotActive: No conversion ongoing
1: Active: ADC operating and may be converting

ADSTP

Bit 4: ADSTP.

Allowed values:
0: NotStopping: No stop command active
1: Stopping: ADC stopping conversion

JADSTP

Bit 5: JADSTP.

Allowed values:
0: NotStopping: No stop command active
1: Stopping: ADC stopping conversion

ADVREGEN

Bits 28-29: ADVREGEN.

Allowed values:
0: Intermediate: Intermediate state required when moving the ADC voltage regulator between states
1: Enabled: ADC voltage regulator enabled
2: Disabled: ADC voltage regulator disabled

ADCALDIF

Bit 30: ADCALDIF.

Allowed values:
0: SingleEnded: Calibration for single-ended mode
1: Differential: Calibration for differential mode

ADCAL

Bit 31: ADCAL.

Allowed values:
0: Complete: Calibration complete
1: Calibration: Start the calibration of the ADC

CFGR

configuration register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

18/18 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
	AWD1CH rw					JAUTO rw	JAWD1EN rw	AWD1EN rw	AWD1SGL rw	JQM rw	JDISCEN rw	DISCNUM rw			DISCEN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	AUTDLY rw	CONT rw	OVRMOD rw	EXTEN rw		EXTSEL rw				ALIGN rw	RES rw			DMACFG rw	DMAEN rw

Toggle fields

DMAEN

Bit 0: DMAEN.

Allowed values:
0: Disabled: DMA disabled
1: Enabled: DMA enabled

DMACFG

Bit 1: DMACFG.

Allowed values:
0: OneShot: DMA One Shot Mode selected
1: Circular: DMA circular mode selected

RES

Bits 3-4: RES.

Allowed values:
0: Bits12: 12-bit
1: Bits10: 10-bit
2: Bits8: 8-bit
3: Bits6: 6-bit

ALIGN

Bit 5: ALIGN.

Allowed values:
0: Right: Right alignment
1: Left: Left alignment

EXTSEL

Bits 6-9: EXTSEL.

Allowed values:
0: TIM1_CC1: Timer 1 CC1 event
1: TIM1_CC2: Timer 1 CC2 event
2: TIM1_CC3: Timer 1 CC3 event
3: TIM2_CC2: Timer 2 CC2 event
4: TIM3_TRGO: Timer 3 TRGO event
6: EXTI11: EXTI line 11
7: HRTIM_ADCTRG1: HRTIM_ADCTRG1 event
8: HRTIM_ADCTRG3: HRTIM_ADCTRG3 event
9: TIM1_TRGO: Timer 1 TRGO event
10: TIM1_TRGO2: Timer 1 TRGO2 event
11: TIM2_TRGO: Timer 2 TRGO event
13: TIM6_TRGO: Timer 6 TRGO event
14: TIM15_TRGO: Timer 15 TRGO event
15: TIM3_CC4: Timer 3 CC4 event

EXTEN

Bits 10-11: EXTEN.

Allowed values:
0: Disabled: Trigger detection disabled
1: RisingEdge: Trigger detection on the rising edge
2: FallingEdge: Trigger detection on the falling edge
3: BothEdges: Trigger detection on both the rising and falling edges

OVRMOD

Bit 12: OVRMOD.

Allowed values:
0: Preserve: Preserve DR register when an overrun is detected
1: Overwrite: Overwrite DR register when an overrun is detected

CONT

Bit 13: CONT.

Allowed values:
0: Single: Single conversion mode
1: Continuous: Continuous conversion mode

AUTDLY

Bit 14: AUTDLY.

Allowed values:
0: Off: Auto delayed conversion mode off
1: On: Auto delayed conversion mode on

DISCEN

Bit 16: DISCEN.

Allowed values:
0: Disabled: Discontinuous mode on regular channels disabled
1: Enabled: Discontinuous mode on regular channels enabled

DISCNUM

Bits 17-19: DISCNUM.

Allowed values: 0x0-0x7

JDISCEN

Bit 20: JDISCEN.

Allowed values:
0: Disabled: Discontinuous mode on injected channels disabled
1: Enabled: Discontinuous mode on injected channels enabled

JQM

Bit 21: JQM.

Allowed values:
0: Mode0: JSQR Mode 0: Queue maintains the last written configuration into JSQR
1: Mode1: JSQR Mode 1: An empty queue disables software and hardware triggers of the injected sequence

AWD1SGL

Bit 22: AWD1SGL.

Allowed values:
0: All: Analog watchdog 1 enabled on all channels
1: Single: Analog watchdog 1 enabled on single channel selected in AWD1CH

AWD1EN

Bit 23: AWD1EN.

Allowed values:
0: Disabled: Analog watchdog 1 disabled on regular channels
1: Enabled: Analog watchdog 1 enabled on regular channels

JAWD1EN

Bit 24: JAWD1EN.

Allowed values:
0: Disabled: Analog watchdog 1 disabled on injected channels
1: Enabled: Analog watchdog 1 enabled on injected channels

JAUTO

Bit 25: JAUTO.

Allowed values:
0: Disabled: Automatic injected group conversion disabled
1: Enabled: Automatic injected group conversion enabled

AWD1CH

Bits 26-30: AWDCH1CH.

Allowed values: 0x0-0x13

SMPR1

sample time register 1

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

9/9 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
		SMP9 rw			SMP8 rw			SMP7 rw			SMP6 rw			SMP5 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SMP5 rw	SMP4 rw			SMP3 rw			SMP2 rw			SMP1 rw

Toggle fields

SMP1

Bits 3-5: SMP1.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP2

Bits 6-8: SMP2.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP3

Bits 9-11: SMP3.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP4

Bits 12-14: SMP4.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP5

Bits 15-17: SMP5.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP6

Bits 18-20: SMP6.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP7

Bits 21-23: SMP7.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP8

Bits 24-26: SMP8.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP9

Bits 27-29: SMP9.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMPR2

sample time register 2

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

9/9 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
					SMP18 rw			SMP17 rw			SMP16 rw			SMP15 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SMP15 rw	SMP14 rw			SMP13 rw			SMP12 rw			SMP11 rw			SMP10 rw

Toggle fields

SMP10

Bits 0-2: SMP10.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP11

Bits 3-5: SMP11.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP12

Bits 6-8: SMP12.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP13

Bits 9-11: SMP13.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP14

Bits 12-14: SMP14.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP15

Bits 15-17: SMP15.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP16

Bits 18-20: SMP16.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP17

Bits 21-23: SMP17.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

SMP18

Bits 24-26: SMP18.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles2_5: 2.5 ADC clock cycles
2: Cycles4_5: 4.5 ADC clock cycles
3: Cycles7_5: 7.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles61_5: 61.5 ADC clock cycles
6: Cycles181_5: 181.5 ADC clock cycles
7: Cycles601_5: 601.5 ADC clock cycles

TR1

watchdog threshold register 1

Offset: 0x20, size: 32, reset: 0x0FFF0000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				HT1 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				LT1 rw

Toggle fields

LT1

Bits 0-11: LT1.

Allowed values: 0x0-0xfff

HT1

Bits 16-27: HT1.

Allowed values: 0x0-0xfff

TR2

watchdog threshold register

Offset: 0x24, size: 32, reset: 0x0FFF0000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								HT2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								LT2 rw

Toggle fields

LT2

Bits 0-7: LT2.

Allowed values: 0x0-0xff

HT2

Bits 16-23: HT2.

Allowed values: 0x0-0xff

TR3

watchdog threshold register 3

Offset: 0x28, size: 32, reset: 0x0FFF0000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								HT3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								LT3 rw

Toggle fields

LT3

Bits 0-7: LT3.

Allowed values: 0x0-0xff

HT3

Bits 16-23: HT3.

Allowed values: 0x0-0xff

SQR1

regular sequence register 1

Offset: 0x30, size: 32, reset: 0x00000000, access: read-write

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
			SQ4 rw						SQ3 rw						SQ2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SQ2 rw					SQ1 rw							L rw

Toggle fields

L

Bits 0-3: L3.

Allowed values: 0x0-0xf

SQ1

Bits 6-10: SQ1.

Allowed values: 0x0-0x13

SQ2

Bits 12-16: SQ2.

Allowed values: 0x0-0x13

SQ3

Bits 18-22: SQ3.

Allowed values: 0x0-0x13

SQ4

Bits 24-28: SQ4.

Allowed values: 0x0-0x13

SQR2

regular sequence register 2

Offset: 0x34, size: 32, reset: 0x00000000, access: read-write

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
			SQ9 rw						SQ8 rw						SQ7 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SQ7 rw					SQ6 rw						SQ5 rw

Toggle fields

SQ5

Bits 0-4: SQ5.

Allowed values: 0x0-0x13

SQ6

Bits 6-10: SQ6.

Allowed values: 0x0-0x13

SQ7

Bits 12-16: SQ7.

Allowed values: 0x0-0x13

SQ8

Bits 18-22: SQ8.

Allowed values: 0x0-0x13

SQ9

Bits 24-28: SQ9.

Allowed values: 0x0-0x13

SQR3

regular sequence register 3

Offset: 0x38, size: 32, reset: 0x00000000, access: read-write

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
			SQ14 rw						SQ13 rw						SQ12 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SQ12 rw					SQ11 rw						SQ10 rw

Toggle fields

SQ10

Bits 0-4: SQ10.

Allowed values: 0x0-0x13

SQ11

Bits 6-10: SQ11.

Allowed values: 0x0-0x13

SQ12

Bits 12-16: SQ12.

Allowed values: 0x0-0x13

SQ13

Bits 18-22: SQ13.

Allowed values: 0x0-0x13

SQ14

Bits 24-28: SQ14.

Allowed values: 0x0-0x13

SQR4

regular sequence register 4

Offset: 0x3c, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
					SQ16 rw						SQ15 rw

Toggle fields

SQ15

Bits 0-4: SQ15.

Allowed values: 0x0-0x13

SQ16

Bits 6-10: SQ16.

Allowed values: 0x0-0x13

DR

regular Data Register

Offset: 0x40, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RDATA r

Toggle fields

RDATA

Bits 0-15: Regular data.

JSQR

injected sequence register

Offset: 0x4c, size: 32, reset: 0x00000000, access: read-write

7/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
	JSQ4 rw						JSQ3 rw						JSQ2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
JSQ2 rw			JSQ1 rw					JEXTEN rw		JEXTSEL rw				JL rw

Toggle fields

JL

Bits 0-1: JL.

Allowed values: 0x0-0x3

JEXTSEL

Bits 2-5: JEXTSEL.

Allowed values:
0: TIM1_TRGO: Timer 1 TRGO event
1: TIM1_CC4: Timer 1 CC4 event
2: TIM2_TRGO: Timer 2 TRGO event
3: TIM2_CC1: Timer 2 CC1 event
4: TIM3_CC4: Timer 3 CC4 event
6: EXTI15: EXTI line 15
8: TIM1_TRGO2: Timer 1 TRGO2 event
9: HRTIM_ADCTRG2: HRTIM_ADCTRG2 event
10: HRTIM_ADCTRG4: HRTIM_ADCTRG4 event
11: TIM3_CC3: Timer 3 CC3 event
12: TIM3_TRGO: Timer 3 TRGO event
13: TIM3_CC1: Timer 3 CC1 event
14: TIM6_TRGO: Timer 6 TRGO event
15: TIM15_TRGO: Timer 15 TRGO event

JEXTEN

Bits 6-7: JEXTEN.

Allowed values:
0: Disabled: Trigger detection disabled
1: RisingEdge: Trigger detection on the rising edge
2: FallingEdge: Trigger detection on the falling edge
3: BothEdges: Trigger detection on both the rising and falling edges

JSQ1

Bits 8-12: JSQ1.

Allowed values: 0x0-0x13

JSQ2

Bits 14-18: JSQ2.

Allowed values: 0x0-0x13

JSQ3

Bits 20-24: JSQ3.

Allowed values: 0x0-0x13

JSQ4

Bits 26-30: JSQ4.

Allowed values: 0x0-0x13

OFR1

offset register 1

Offset: 0x60, size: 32, reset: 0x00000000, access: read-write

3/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OFFSET1_EN rw	OFFSET1_CH rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				OFFSET1 rw

Toggle fields

OFFSET1

Bits 0-11: OFFSET1.

Allowed values: 0x0-0xfff

OFFSET1_CH

Bits 26-30: OFFSET1_CH.

Allowed values: 0x0-0x1f

OFFSET1_EN

Bit 31: OFFSET1_EN.

Allowed values:
0: Disabled: Offset disabled
1: Enabled: Offset enabled

OFR2

offset register 2

Offset: 0x64, size: 32, reset: 0x00000000, access: read-write

3/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OFFSET2_EN rw	OFFSET2_CH rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				OFFSET2 rw

Toggle fields

OFFSET2

Bits 0-11: OFFSET2.

Allowed values: 0x0-0xfff

OFFSET2_CH

Bits 26-30: OFFSET2_CH.

Allowed values: 0x0-0x1f

OFFSET2_EN

Bit 31: OFFSET2_EN.

Allowed values:
0: Disabled: Offset disabled
1: Enabled: Offset enabled

OFR3

offset register 3

Offset: 0x68, size: 32, reset: 0x00000000, access: read-write

3/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OFFSET3_EN rw	OFFSET3_CH rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				OFFSET3 rw

Toggle fields

OFFSET3

Bits 0-11: OFFSET3.

Allowed values: 0x0-0xfff

OFFSET3_CH

Bits 26-30: OFFSET3_CH.

Allowed values: 0x0-0x1f

OFFSET3_EN

Bit 31: OFFSET3_EN.

Allowed values:
0: Disabled: Offset disabled
1: Enabled: Offset enabled

OFR4

offset register 4

Offset: 0x6c, size: 32, reset: 0x00000000, access: read-write

3/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OFFSET4_EN rw	OFFSET4_CH rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				OFFSET4 rw

Toggle fields

OFFSET4

Bits 0-11: OFFSET4.

Allowed values: 0x0-0xfff

OFFSET4_CH

Bits 26-30: OFFSET4_CH.

Allowed values: 0x0-0x1f

OFFSET4_EN

Bit 31: OFFSET4_EN.

Allowed values:
0: Disabled: Offset disabled
1: Enabled: Offset enabled

JDR1

injected data register 1

Offset: 0x80, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
JDATA1 r

Toggle fields

JDATA1

Bits 0-15: JDATA1.

JDR2

injected data register 2

Offset: 0x84, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
JDATA2 r

Toggle fields

JDATA2

Bits 0-15: JDATA2.

JDR3

injected data register 3

Offset: 0x88, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
JDATA3 r

Toggle fields

JDATA3

Bits 0-15: JDATA3.

JDR4

injected data register 4

Offset: 0x8c, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
JDATA4 r

Toggle fields

JDATA4

Bits 0-15: JDATA4.

AWD2CR

Analog Watchdog 2 Configuration Register

Offset: 0xa0, size: 32, reset: 0x00000000, access: read-write

18/18 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
													AWD2CH17 rw	AWD2CH16 rw	AWD2CH15 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AWD2CH14 rw	AWD2CH13 rw	AWD2CH12 rw	AWD2CH11 rw	AWD2CH10 rw	AWD2CH9 rw	AWD2CH8 rw	AWD2CH7 rw	AWD2CH6 rw	AWD2CH5 rw	AWD2CH4 rw	AWD2CH3 rw	AWD2CH2 rw	AWD2CH1 rw	AWD2CH0 rw

Toggle fields

AWD2CH0

Bit 1: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH1

Bit 2: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH2

Bit 3: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH3

Bit 4: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH4

Bit 5: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH5

Bit 6: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH6

Bit 7: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH7

Bit 8: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH8

Bit 9: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH9

Bit 10: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH10

Bit 11: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH11

Bit 12: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH12

Bit 13: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH13

Bit 14: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH14

Bit 15: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH15

Bit 16: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH16

Bit 17: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD2CH17

Bit 18: AWD2CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CR

Analog Watchdog 3 Configuration Register

Offset: 0xa4, size: 32, reset: 0x00000000, access: read-write

18/18 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
													AWD3CH17 rw	AWD3CH16 rw	AWD3CH15 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AWD3CH14 rw	AWD3CH13 rw	AWD3CH12 rw	AWD3CH11 rw	AWD3CH10 rw	AWD3CH9 rw	AWD3CH8 rw	AWD3CH7 rw	AWD3CH6 rw	AWD3CH5 rw	AWD3CH4 rw	AWD3CH3 rw	AWD3CH2 rw	AWD3CH1 rw	AWD3CH0 rw

Toggle fields

AWD3CH0

Bit 1: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH1

Bit 2: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH2

Bit 3: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH3

Bit 4: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH4

Bit 5: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH5

Bit 6: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH6

Bit 7: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH7

Bit 8: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH8

Bit 9: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH9

Bit 10: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH10

Bit 11: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH11

Bit 12: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH12

Bit 13: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH13

Bit 14: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH14

Bit 15: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH15

Bit 16: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH16

Bit 17: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

AWD3CH17

Bit 18: AWD3CH.

Allowed values:
0: NotMonitored: Input channel not monitored by AWDx
1: Monitored: Input channel monitored by AWDx

DIFSEL

Differential Mode Selection Register 2

Offset: 0xb0, size: 32, reset: 0x00000000, access: Unspecified

18/18 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
													DIFSEL_117 N/A	DIFSEL_116 N/A	DIFSEL_115 N/A
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DIFSEL_114 N/A	DIFSEL_113 N/A	DIFSEL_112 N/A	DIFSEL_111 N/A	DIFSEL_110 N/A	DIFSEL_19 N/A	DIFSEL_18 N/A	DIFSEL_17 N/A	DIFSEL_16 N/A	DIFSEL_15 N/A	DIFSEL_14 N/A	DIFSEL_13 N/A	DIFSEL_12 N/A	DIFSEL_11 N/A	DIFSEL_10 N/A

Toggle fields

DIFSEL_10

Bit 1: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_11

Bit 2: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_12

Bit 3: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_13

Bit 4: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_14

Bit 5: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_15

Bit 6: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_16

Bit 7: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_17

Bit 8: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_18

Bit 9: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_19

Bit 10: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_110

Bit 11: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_111

Bit 12: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_112

Bit 13: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_113

Bit 14: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_114

Bit 15: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_115

Bit 16: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_116

Bit 17: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

DIFSEL_117

Bit 18: Differential mode for channels 15 to 1.

Allowed values:
0: SingleEnded: Input channel is configured in single-ended mode
1: Differential: Input channel is configured in differential mode

CALFACT

Calibration Factors

Offset: 0xb4, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
									CALFACT_D rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
									CALFACT_S rw

Toggle fields

CALFACT_S

Bits 0-6: CALFACT_S.

Allowed values: 0x0-0x7f

CALFACT_D

Bits 16-22: CALFACT_D.

Allowed values: 0x0-0x7f

CAN

0x40006400: Controller area network

82/323 fields covered.

Toggle register map

Offset	Name	31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	MCR																DBF	RESET								TTCM	ABOM	AWUM	NART	RFLM	TXFP	SLEEP	INRQ
0x4	MSR																					RX	SAMP	RXM	TXM				SLAKI	WKUI	ERRI	SLAK	INAK
0x8	TSR	LOW[2]	LOW[1]	LOW[0]	TME[2]	TME[1]	TME[0]	CODE		ABRQ2				TERR2	ALST2	TXOK2	RQCP2	ABRQ1				TERR1	ALST1	TXOK1	RQCP1	ABRQ0				TERR0	ALST0	TXOK0	RQCP0
0xc	RF[0]R																											RFOM	FOVR	FULL		FMP
0x10	RF[1]R																											RFOM	FOVR	FULL		FMP
0x14	IER															SLKIE	WKUIE	ERRIE				LECIE	BOFIE	EPVIE	EWGIE		FOVIE1	FFIE1	FMPIE1	FOVIE0	FFIE0	FMPIE0	TMEIE
0x18	ESR	REC								TEC																	LEC				BOFF	EPVF	EWGF
0x1c	BTR	SILM	LBKM					SJW			TS2			TS1										BRP
0x180	TIR [0]	STID											EXID					EXID													IDE	RTR	TXRQ
0x184	TDTR [0]	TIME																							TGT					DLC
0x188	TDLR [0]	DATA[3]								DATA[2]								DATA[1]								DATA[0]
0x18c	TDHR [0]	DATA[7]								DATA[6]								DATA[5]								DATA[4]
0x190	TIR [1]	STID											EXID					EXID													IDE	RTR	TXRQ
0x194	TDTR [1]	TIME																							TGT					DLC
0x198	TDLR [1]	DATA[3]								DATA[2]								DATA[1]								DATA[0]
0x19c	TDHR [1]	DATA[7]								DATA[6]								DATA[5]								DATA[4]
0x1a0	TIR [2]	STID											EXID					EXID													IDE	RTR	TXRQ
0x1a4	TDTR [2]	TIME																							TGT					DLC
0x1a8	TDLR [2]	DATA[3]								DATA[2]								DATA[1]								DATA[0]
0x1ac	TDHR [2]	DATA[7]								DATA[6]								DATA[5]								DATA[4]
0x1b0	RIR [0]	STID											EXID					EXID													IDE	RTR
0x1b4	RDTR [0]	TIME																FMI												DLC
0x1b8	RDLR [0]	DATA[3]								DATA[2]								DATA[1]								DATA[0]
0x1bc	RDHR [0]	DATA[7]								DATA[6]								DATA[5]								DATA[4]
0x1c0	RIR [1]	STID											EXID					EXID													IDE	RTR
0x1c4	RDTR [1]	TIME																FMI												DLC
0x1c8	RDLR [1]	DATA[3]								DATA[2]								DATA[1]								DATA[0]
0x1cc	RDHR [1]	DATA[7]								DATA[6]								DATA[5]								DATA[4]
0x200	FMR																			CAN2SB													FINIT
0x204	FM1R					FBM[27]	FBM[26]	FBM[25]	FBM[24]	FBM[23]	FBM[22]	FBM[21]	FBM[20]	FBM[19]	FBM[18]	FBM[17]	FBM[16]	FBM[15]	FBM[14]	FBM[13]	FBM[12]	FBM[11]	FBM[10]	FBM[9]	FBM[8]	FBM[7]	FBM[6]	FBM[5]	FBM[4]	FBM[3]	FBM[2]	FBM[1]	FBM[0]
0x20c	FS1R					FSC[27]	FSC[26]	FSC[25]	FSC[24]	FSC[23]	FSC[22]	FSC[21]	FSC[20]	FSC[19]	FSC[18]	FSC[17]	FSC[16]	FSC[15]	FSC[14]	FSC[13]	FSC[12]	FSC[11]	FSC[10]	FSC[9]	FSC[8]	FSC[7]	FSC[6]	FSC[5]	FSC[4]	FSC[3]	FSC[2]	FSC[1]	FSC[0]
0x214	FFA1R					FFA[27]	FFA[26]	FFA[25]	FFA[24]	FFA[23]	FFA[22]	FFA[21]	FFA[20]	FFA[19]	FFA[18]	FFA[17]	FFA[16]	FFA[15]	FFA[14]	FFA[13]	FFA[12]	FFA[11]	FFA[10]	FFA[9]	FFA[8]	FFA[7]	FFA[6]	FFA[5]	FFA[4]	FFA[3]	FFA[2]	FFA[1]	FFA[0]
0x21c	FA1R					FACT[27]	FACT[26]	FACT[25]	FACT[24]	FACT[23]	FACT[22]	FACT[21]	FACT[20]	FACT[19]	FACT[18]	FACT[17]	FACT[16]	FACT[15]	FACT[14]	FACT[13]	FACT[12]	FACT[11]	FACT[10]	FACT[9]	FACT[8]	FACT[7]	FACT[6]	FACT[5]	FACT[4]	FACT[3]	FACT[2]	FACT[1]	FACT[0]
0x240	FR1 [0]	FB																FB
0x244	FR2 [0]	FB																FB
0x248	FR1 [1]	FB																FB
0x24c	FR2 [1]	FB																FB
0x250	FR1 [2]	FB																FB
0x254	FR2 [2]	FB																FB
0x258	FR1 [3]	FB																FB
0x25c	FR2 [3]	FB																FB
0x260	FR1 [4]	FB																FB
0x264	FR2 [4]	FB																FB
0x268	FR1 [5]	FB																FB
0x26c	FR2 [5]	FB																FB
0x270	FR1 [6]	FB																FB
0x274	FR2 [6]	FB																FB
0x278	FR1 [7]	FB																FB
0x27c	FR2 [7]	FB																FB
0x280	FR1 [8]	FB																FB
0x284	FR2 [8]	FB																FB
0x288	FR1 [9]	FB																FB
0x28c	FR2 [9]	FB																FB
0x290	FR1 [10]	FB																FB
0x294	FR2 [10]	FB																FB
0x298	FR1 [11]	FB																FB
0x29c	FR2 [11]	FB																FB
0x2a0	FR1 [12]	FB																FB
0x2a4	FR2 [12]	FB																FB
0x2a8	FR1 [13]	FB																FB
0x2ac	FR2 [13]	FB																FB
0x2b0	FR1 [14]	FB																FB
0x2b4	FR2 [14]	FB																FB
0x2b8	FR1 [15]	FB																FB
0x2bc	FR2 [15]	FB																FB
0x2c0	FR1 [16]	FB																FB
0x2c4	FR2 [16]	FB																FB
0x2c8	FR1 [17]	FB																FB
0x2cc	FR2 [17]	FB																FB
0x2d0	FR1 [18]	FB																FB
0x2d4	FR2 [18]	FB																FB
0x2d8	FR1 [19]	FB																FB
0x2dc	FR2 [19]	FB																FB
0x2e0	FR1 [20]	FB																FB
0x2e4	FR2 [20]	FB																FB
0x2e8	FR1 [21]	FB																FB
0x2ec	FR2 [21]	FB																FB
0x2f0	FR1 [22]	FB																FB
0x2f4	FR2 [22]	FB																FB
0x2f8	FR1 [23]	FB																FB
0x2fc	FR2 [23]	FB																FB
0x300	FR1 [24]	FB																FB
0x304	FR2 [24]	FB																FB
0x308	FR1 [25]	FB																FB
0x30c	FR2 [25]	FB																FB
0x310	FR1 [26]	FB																FB
0x314	FR2 [26]	FB																FB
0x318	FR1 [27]	FB																FB
0x31c	FR2 [27]	FB																FB

Toggle registers

MCR

master control register

Offset: 0x0, size: 32, reset: 0x00010002, access: read-write

0/10 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															DBF rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RESET rw								TTCM rw	ABOM rw	AWUM rw	NART rw	RFLM rw	TXFP rw	SLEEP rw	INRQ rw

Toggle fields

INRQ

Bit 0: INRQ.

SLEEP

Bit 1: SLEEP.

TXFP

Bit 2: TXFP.

RFLM

Bit 3: RFLM.

NART

Bit 4: NART.

AWUM

Bit 5: AWUM.

ABOM

Bit 6: ABOM.

TTCM

Bit 7: TTCM.

RESET

Bit 15: RESET.

DBF

Bit 16: DBF.

MSR

master status register

Offset: 0x4, size: 32, reset: 0x00000C02, access: Unspecified

6/9 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				RX r	SAMP r	RXM r	TXM r				SLAKI rw	WKUI rw	ERRI rw	SLAK r	INAK r

Toggle fields

INAK

Bit 0: INAK.

SLAK

Bit 1: SLAK.

ERRI

Bit 2: ERRI.

WKUI

Bit 3: WKUI.

SLAKI

Bit 4: SLAKI.

TXM

Bit 8: TXM.

RXM

Bit 9: RXM.

SAMP

Bit 10: SAMP.

RX

Bit 11: RX.

TSR

transmit status register

Offset: 0x8, size: 32, reset: 0x1C000000, access: Unspecified

7/22 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
LOW[2] r	LOW[1] r	LOW[0] r	TME[2] r	TME[1] r	TME[0] r	CODE r		ABRQ2 rw				TERR2 rw	ALST2 rw	TXOK2 rw	RQCP2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ABRQ1 rw				TERR1 rw	ALST1 rw	TXOK1 rw	RQCP1 rw	ABRQ0 rw				TERR0 rw	ALST0 rw	TXOK0 rw	RQCP0 rw

Toggle fields

RQCP0

Bit 0: RQCP0.

TXOK0

Bit 1: TXOK0.

ALST0

Bit 2: ALST0.

TERR0

Bit 3: TERR0.

ABRQ0

Bit 7: ABRQ0.

RQCP1

Bit 8: RQCP1.

TXOK1

Bit 9: TXOK1.

ALST1

Bit 10: ALST1.

TERR1

Bit 11: TERR1.

ABRQ1

Bit 15: ABRQ1.

RQCP2

Bit 16: RQCP2.

TXOK2

Bit 17: TXOK2.

ALST2

Bit 18: ALST2.

TERR2

Bit 19: TERR2.

ABRQ2

Bit 23: ABRQ2.

CODE

Bits 24-25: CODE.

TME[0]

Bit 26: Lowest priority flag for mailbox 0.

TME[1]

Bit 27: Lowest priority flag for mailbox 1.

TME[2]

Bit 28: Lowest priority flag for mailbox 2.

LOW[0]

Bit 29: Lowest priority flag for mailbox 0.

LOW[1]

Bit 30: Lowest priority flag for mailbox 1.

LOW[2]

Bit 31: Lowest priority flag for mailbox 2.

RF[0]R

receive FIFO 0 register

Offset: 0xc, size: 32, reset: 0x00000000, access: Unspecified

4/4 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
										RFOM rw	FOVR rw	FULL rw		FMP r

Toggle fields

FMP

Bits 0-1: FMP0.

FULL

Bit 3: FULL0.

Allowed values:
0: NotFull: FIFO x is not full
1: Full: FIFO x is full

FOVR

Bit 4: FOVR0.

Allowed values:
0: NoOverrun: No FIFO x overrun
1: Overrun: FIFO x overrun

RFOM

Bit 5: RFOM0.

Allowed values:
1: Release: Set by software to release the output mailbox of the FIFO

RF[1]R

receive FIFO 1 register

Offset: 0x10, size: 32, reset: 0x00000000, access: Unspecified

4/4 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
										RFOM rw	FOVR rw	FULL rw		FMP r

Toggle fields

FMP

Bits 0-1: FMP0.

FULL

Bit 3: FULL0.

Allowed values:
0: NotFull: FIFO x is not full
1: Full: FIFO x is full

FOVR

Bit 4: FOVR0.

Allowed values:
0: NoOverrun: No FIFO x overrun
1: Overrun: FIFO x overrun

RFOM

Bit 5: RFOM0.

Allowed values:
1: Release: Set by software to release the output mailbox of the FIFO

IER

interrupt enable register

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

14/14 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
														SLKIE rw	WKUIE rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ERRIE rw				LECIE rw	BOFIE rw	EPVIE rw	EWGIE rw		FOVIE1 rw	FFIE1 rw	FMPIE1 rw	FOVIE0 rw	FFIE0 rw	FMPIE0 rw	TMEIE rw

Toggle fields

TMEIE

Bit 0: TMEIE.

Allowed values:
0: Disabled: No interrupt when RQCPx bit is set
1: Enabled: Interrupt generated when RQCPx bit is set

FMPIE0

Bit 1: FMPIE0.

Allowed values:
0: Disabled: No interrupt generated when state of FMP[1:0] bits are not 00
1: Enabled: Interrupt generated when state of FMP[1:0] bits are not 00b

FFIE0

Bit 2: FFIE0.

Allowed values:
0: Disabled: No interrupt when FULL bit is set
1: Enabled: Interrupt generated when FULL bit is set

FOVIE0

Bit 3: FOVIE0.

Allowed values:
0: Disabled: No interrupt when FOVR bit is set
1: Enabled: Interrupt generated when FOVR bit is set

FMPIE1

Bit 4: FMPIE1.

Allowed values:
0: Disabled: No interrupt generated when state of FMP[1:0] bits are not 00b
1: Enabled: Interrupt generated when state of FMP[1:0] bits are not 00b

FFIE1

Bit 5: FFIE1.

Allowed values:
0: Disabled: No interrupt when FULL bit is set
1: Enabled: Interrupt generated when FULL bit is set

FOVIE1

Bit 6: FOVIE1.

Allowed values:
0: Disabled: No interrupt when FOVR is set
1: Enabled: Interrupt generation when FOVR is set

EWGIE

Bit 8: EWGIE.

Allowed values:
0: Disabled: ERRI bit will not be set when EWGF is set
1: Enabled: ERRI bit will be set when EWGF is set

EPVIE

Bit 9: EPVIE.

Allowed values:
0: Disabled: ERRI bit will not be set when EPVF is set
1: Enabled: ERRI bit will be set when EPVF is set

BOFIE

Bit 10: BOFIE.

Allowed values:
0: Disabled: ERRI bit will not be set when BOFF is set
1: Enabled: ERRI bit will be set when BOFF is set

LECIE

Bit 11: LECIE.

Allowed values:
0: Disabled: ERRI bit will not be set when the error code in LEC[2:0] is set by hardware on error detection
1: Enabled: ERRI bit will be set when the error code in LEC[2:0] is set by hardware on error detection

ERRIE

Bit 15: ERRIE.

Allowed values:
0: Disabled: No interrupt will be generated when an error condition is pending in the CAN_ESR
1: Enabled: An interrupt will be generation when an error condition is pending in the CAN_ESR

WKUIE

Bit 16: WKUIE.

Allowed values:
0: Disabled: No interrupt when WKUI is set
1: Enabled: Interrupt generated when WKUI bit is set

SLKIE

Bit 17: SLKIE.

Allowed values:
0: Disabled: No interrupt when SLAKI bit is set
1: Enabled: Interrupt generated when SLAKI bit is set

ESR

error status register

Offset: 0x18, size: 32, reset: 0x00000000, access: Unspecified

6/6 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
REC r								TEC r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
									LEC rw				BOFF r	EPVF r	EWGF r

Toggle fields

EWGF

Bit 0: EWGF.

EPVF

Bit 1: EPVF.

BOFF

Bit 2: BOFF.

LEC

Bits 4-6: LEC.

Allowed values:
0: NoError: No Error
1: Stuff: Stuff Error
2: Form: Form Error
3: Ack: Acknowledgment Error
4: BitRecessive: Bit recessive Error
5: BitDominant: Bit dominant Error
6: Crc: CRC Error
7: Custom: Set by software

TEC

Bits 16-23: TEC.

REC

Bits 24-31: REC.

BTR

bit timing register

Offset: 0x1c, size: 32, reset: 0x01230000, access: read-write

2/6 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
SILM rw	LBKM rw					SJW rw			TS2 rw			TS1 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						BRP rw

Toggle fields

BRP

Bits 0-9: BRP.

TS1

Bits 16-19: TS1.

TS2

Bits 20-22: TS2.

SJW

Bits 24-25: SJW.

LBKM

Bit 30: LBKM.

Allowed values:
0: Disabled: Loop Back Mode disabled
1: Enabled: Loop Back Mode enabled

SILM

Bit 31: SILM.

Allowed values:
0: Normal: Normal operation
1: Silent: Silent Mode

TIR [0]

TX mailbox identifier register

Offset: 0x180, size: 32, reset: 0x00000000, access: read-write

2/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
STID rw											EXID rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
EXID rw													IDE rw	RTR rw	TXRQ rw

Toggle fields

TXRQ

Bit 0: TXRQ.

RTR

Bit 1: RTR.

Allowed values:
0: Data: Data frame
1: Remote: Remote frame

IDE

Bit 2: IDE.

Allowed values:
0: Standard: Standard identifier
1: Extended: Extended identifier

EXID

Bits 3-20: EXID.

STID

Bits 21-31: STID.

TDTR [0]

mailbox data length control and time stamp register

Offset: 0x184, size: 32, reset: 0x00000000, access: read-write

1/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
TIME rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							TGT rw					DLC rw

Toggle fields

DLC

Bits 0-3: DLC.

Allowed values: 0x0-0x8

TGT

Bit 8: TGT.

TIME

Bits 16-31: TIME.

TDLR [0]

mailbox data low register

Offset: 0x188, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
DATA[3] rw								DATA[2] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DATA[1] rw								DATA[0] rw

Toggle fields

DATA[0]

Bits 0-7: DATA0.

DATA[1]

Bits 8-15: DATA1.

DATA[2]

Bits 16-23: DATA2.

DATA[3]

Bits 24-31: DATA3.

TDHR [0]

mailbox data high register

Offset: 0x18c, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
DATA[7] rw								DATA[6] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DATA[5] rw								DATA[4] rw

Toggle fields

DATA[4]

Bits 0-7: DATA4.

DATA[5]

Bits 8-15: DATA5.

DATA[6]

Bits 16-23: DATA6.

DATA[7]

Bits 24-31: DATA7.

TIR [1]

TX mailbox identifier register

Offset: 0x190, size: 32, reset: 0x00000000, access: read-write

2/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
STID rw											EXID rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
EXID rw													IDE rw	RTR rw	TXRQ rw

Toggle fields

TXRQ

Bit 0: TXRQ.

RTR

Bit 1: RTR.

Allowed values:
0: Data: Data frame
1: Remote: Remote frame

IDE

Bit 2: IDE.

Allowed values:
0: Standard: Standard identifier
1: Extended: Extended identifier

EXID

Bits 3-20: EXID.

STID

Bits 21-31: STID.

TDTR [1]

mailbox data length control and time stamp register

Offset: 0x194, size: 32, reset: 0x00000000, access: read-write

1/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
TIME rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							TGT rw					DLC rw

Toggle fields

DLC

Bits 0-3: DLC.

Allowed values: 0x0-0x8

TGT

Bit 8: TGT.

TIME

Bits 16-31: TIME.

TDLR [1]

mailbox data low register

Offset: 0x198, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
DATA[3] rw								DATA[2] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DATA[1] rw								DATA[0] rw

Toggle fields

DATA[0]

Bits 0-7: DATA0.

DATA[1]

Bits 8-15: DATA1.

DATA[2]

Bits 16-23: DATA2.

DATA[3]

Bits 24-31: DATA3.

TDHR [1]

mailbox data high register

Offset: 0x19c, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
DATA[7] rw								DATA[6] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DATA[5] rw								DATA[4] rw

Toggle fields

DATA[4]

Bits 0-7: DATA4.

DATA[5]

Bits 8-15: DATA5.

DATA[6]

Bits 16-23: DATA6.

DATA[7]

Bits 24-31: DATA7.

TIR [2]

TX mailbox identifier register

Offset: 0x1a0, size: 32, reset: 0x00000000, access: read-write

2/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
STID rw											EXID rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
EXID rw													IDE rw	RTR rw	TXRQ rw

Toggle fields

TXRQ

Bit 0: TXRQ.

RTR

Bit 1: RTR.

Allowed values:
0: Data: Data frame
1: Remote: Remote frame

IDE

Bit 2: IDE.

Allowed values:
0: Standard: Standard identifier
1: Extended: Extended identifier

EXID

Bits 3-20: EXID.

STID

Bits 21-31: STID.

TDTR [2]

mailbox data length control and time stamp register

Offset: 0x1a4, size: 32, reset: 0x00000000, access: read-write

1/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
TIME rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							TGT rw					DLC rw

Toggle fields

DLC

Bits 0-3: DLC.

Allowed values: 0x0-0x8

TGT

Bit 8: TGT.

TIME

Bits 16-31: TIME.

TDLR [2]

mailbox data low register

Offset: 0x1a8, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
DATA[3] rw								DATA[2] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DATA[1] rw								DATA[0] rw

Toggle fields

DATA[0]

Bits 0-7: DATA0.

DATA[1]

Bits 8-15: DATA1.

DATA[2]

Bits 16-23: DATA2.

DATA[3]

Bits 24-31: DATA3.

TDHR [2]

mailbox data high register

Offset: 0x1ac, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
DATA[7] rw								DATA[6] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DATA[5] rw								DATA[4] rw

Toggle fields

DATA[4]

Bits 0-7: DATA4.

DATA[5]

Bits 8-15: DATA5.

DATA[6]

Bits 16-23: DATA6.

DATA[7]

Bits 24-31: DATA7.

RIR [0]

receive FIFO mailbox identifier register

Offset: 0x1b0, size: 32, reset: 0x00000000, access: read-only

4/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
STID r											EXID r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
EXID r													IDE r	RTR r

Toggle fields

RTR

Bit 1: RTR.

Allowed values:
0: Data: Data frame
1: Remote: Remote frame

IDE

Bit 2: IDE.

Allowed values:
0: Standard: Standard identifier
1: Extended: Extended identifier

EXID

Bits 3-20: EXID.

STID

Bits 21-31: STID.

RDTR [0]

receive FIFO mailbox data length control and time stamp register

Offset: 0x1b4, size: 32, reset: 0x00000000, access: read-only

3/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
TIME r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FMI r												DLC r

Toggle fields

DLC

Bits 0-3: DLC.

Allowed values: 0x0-0x8

FMI

Bits 8-15: FMI.

TIME

Bits 16-31: TIME.

RDLR [0]

receive FIFO mailbox data low register

Offset: 0x1b8, size: 32, reset: 0x00000000, access: read-only

4/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
DATA[3] r								DATA[2] r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DATA[1] r								DATA[0] r

Toggle fields

DATA[0]

Bits 0-7: DATA0.

DATA[1]

Bits 8-15: DATA1.

DATA[2]

Bits 16-23: DATA2.

DATA[3]

Bits 24-31: DATA3.

RDHR [0]

receive FIFO mailbox data high register

Offset: 0x1bc, size: 32, reset: 0x00000000, access: read-only

4/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
DATA[7] r								DATA[6] r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DATA[5] r								DATA[4] r

Toggle fields

DATA[4]

Bits 0-7: DATA4.

DATA[5]

Bits 8-15: DATA5.

DATA[6]

Bits 16-23: DATA6.

DATA[7]

Bits 24-31: DATA7.

RIR [1]

receive FIFO mailbox identifier register

Offset: 0x1c0, size: 32, reset: 0x00000000, access: read-only

4/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
STID r											EXID r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
EXID r													IDE r	RTR r

Toggle fields

RTR

Bit 1: RTR.

Allowed values:
0: Data: Data frame
1: Remote: Remote frame

IDE

Bit 2: IDE.

Allowed values:
0: Standard: Standard identifier
1: Extended: Extended identifier

EXID

Bits 3-20: EXID.

STID

Bits 21-31: STID.

RDTR [1]

receive FIFO mailbox data length control and time stamp register

Offset: 0x1c4, size: 32, reset: 0x00000000, access: read-only

3/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
TIME r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FMI r												DLC r

Toggle fields

DLC

Bits 0-3: DLC.

Allowed values: 0x0-0x8

FMI

Bits 8-15: FMI.

TIME

Bits 16-31: TIME.

RDLR [1]

receive FIFO mailbox data low register

Offset: 0x1c8, size: 32, reset: 0x00000000, access: read-only

4/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
DATA[3] r								DATA[2] r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DATA[1] r								DATA[0] r

Toggle fields

DATA[0]

Bits 0-7: DATA0.

DATA[1]

Bits 8-15: DATA1.

DATA[2]

Bits 16-23: DATA2.

DATA[3]

Bits 24-31: DATA3.

RDHR [1]

receive FIFO mailbox data high register

Offset: 0x1cc, size: 32, reset: 0x00000000, access: read-only

4/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
DATA[7] r								DATA[6] r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DATA[5] r								DATA[4] r

Toggle fields

DATA[4]

Bits 0-7: DATA4.

DATA[5]

Bits 8-15: DATA5.

DATA[6]

Bits 16-23: DATA6.

DATA[7]

Bits 24-31: DATA7.

FMR

filter master register

Offset: 0x200, size: 32, reset: 0x2A1C0E01, access: read-write

0/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		CAN2SB rw													FINIT rw

Toggle fields

FINIT

Bit 0: Filter init mode.

CAN2SB

Bits 8-13: CAN2 start bank.

FM1R

filter mode register

Offset: 0x204, size: 32, reset: 0x00000000, access: read-write

0/28 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				FBM[27] rw	FBM[26] rw	FBM[25] rw	FBM[24] rw	FBM[23] rw	FBM[22] rw	FBM[21] rw	FBM[20] rw	FBM[19] rw	FBM[18] rw	FBM[17] rw	FBM[16] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FBM[15] rw	FBM[14] rw	FBM[13] rw	FBM[12] rw	FBM[11] rw	FBM[10] rw	FBM[9] rw	FBM[8] rw	FBM[7] rw	FBM[6] rw	FBM[5] rw	FBM[4] rw	FBM[3] rw	FBM[2] rw	FBM[1] rw	FBM[0] rw

Toggle fields

FBM[0]

Bit 0: Filter mode.

FBM[1]

Bit 1: Filter mode.

FBM[2]

Bit 2: Filter mode.

FBM[3]

Bit 3: Filter mode.

FBM[4]

Bit 4: Filter mode.

FBM[5]

Bit 5: Filter mode.

FBM[6]

Bit 6: Filter mode.

FBM[7]

Bit 7: Filter mode.

FBM[8]

Bit 8: Filter mode.

FBM[9]

Bit 9: Filter mode.

FBM[10]

Bit 10: Filter mode.

FBM[11]

Bit 11: Filter mode.

FBM[12]

Bit 12: Filter mode.

FBM[13]

Bit 13: Filter mode.

FBM[14]

Bit 14: Filter mode.

FBM[15]

Bit 15: Filter mode.

FBM[16]

Bit 16: Filter mode.

FBM[17]

Bit 17: Filter mode.

FBM[18]

Bit 18: Filter mode.

FBM[19]

Bit 19: Filter mode.

FBM[20]

Bit 20: Filter mode.

FBM[21]

Bit 21: Filter mode.

FBM[22]

Bit 22: Filter mode.

FBM[23]

Bit 23: Filter mode.

FBM[24]

Bit 24: Filter mode.

FBM[25]

Bit 25: Filter mode.

FBM[26]

Bit 26: Filter mode.

FBM[27]

Bit 27: Filter mode.

FS1R

filter scale register

Offset: 0x20c, size: 32, reset: 0x00000000, access: read-write

0/28 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				FSC[27] rw	FSC[26] rw	FSC[25] rw	FSC[24] rw	FSC[23] rw	FSC[22] rw	FSC[21] rw	FSC[20] rw	FSC[19] rw	FSC[18] rw	FSC[17] rw	FSC[16] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FSC[15] rw	FSC[14] rw	FSC[13] rw	FSC[12] rw	FSC[11] rw	FSC[10] rw	FSC[9] rw	FSC[8] rw	FSC[7] rw	FSC[6] rw	FSC[5] rw	FSC[4] rw	FSC[3] rw	FSC[2] rw	FSC[1] rw	FSC[0] rw

Toggle fields

FSC[0]

Bit 0: Filter scale configuration.

FSC[1]

Bit 1: Filter scale configuration.

FSC[2]

Bit 2: Filter scale configuration.

FSC[3]

Bit 3: Filter scale configuration.

FSC[4]

Bit 4: Filter scale configuration.

FSC[5]

Bit 5: Filter scale configuration.

FSC[6]

Bit 6: Filter scale configuration.

FSC[7]

Bit 7: Filter scale configuration.

FSC[8]

Bit 8: Filter scale configuration.

FSC[9]

Bit 9: Filter scale configuration.

FSC[10]

Bit 10: Filter scale configuration.

FSC[11]

Bit 11: Filter scale configuration.

FSC[12]

Bit 12: Filter scale configuration.

FSC[13]

Bit 13: Filter scale configuration.

FSC[14]

Bit 14: Filter scale configuration.

FSC[15]

Bit 15: Filter scale configuration.

FSC[16]

Bit 16: Filter scale configuration.

FSC[17]

Bit 17: Filter scale configuration.

FSC[18]

Bit 18: Filter scale configuration.

FSC[19]

Bit 19: Filter scale configuration.

FSC[20]

Bit 20: Filter scale configuration.

FSC[21]

Bit 21: Filter scale configuration.

FSC[22]

Bit 22: Filter scale configuration.

FSC[23]

Bit 23: Filter scale configuration.

FSC[24]

Bit 24: Filter scale configuration.

FSC[25]

Bit 25: Filter scale configuration.

FSC[26]

Bit 26: Filter scale configuration.

FSC[27]

Bit 27: Filter scale configuration.

FFA1R

filter FIFO assignment register

Offset: 0x214, size: 32, reset: 0x00000000, access: read-write

0/28 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				FFA[27] rw	FFA[26] rw	FFA[25] rw	FFA[24] rw	FFA[23] rw	FFA[22] rw	FFA[21] rw	FFA[20] rw	FFA[19] rw	FFA[18] rw	FFA[17] rw	FFA[16] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FFA[15] rw	FFA[14] rw	FFA[13] rw	FFA[12] rw	FFA[11] rw	FFA[10] rw	FFA[9] rw	FFA[8] rw	FFA[7] rw	FFA[6] rw	FFA[5] rw	FFA[4] rw	FFA[3] rw	FFA[2] rw	FFA[1] rw	FFA[0] rw

Toggle fields

FFA[0]

Bit 0: Filter FIFO assignment for filter 0.

FFA[1]

Bit 1: Filter FIFO assignment for filter 1.

FFA[2]

Bit 2: Filter FIFO assignment for filter 2.

FFA[3]

Bit 3: Filter FIFO assignment for filter 3.

FFA[4]

Bit 4: Filter FIFO assignment for filter 4.

FFA[5]

Bit 5: Filter FIFO assignment for filter 5.

FFA[6]

Bit 6: Filter FIFO assignment for filter 6.

FFA[7]

Bit 7: Filter FIFO assignment for filter 7.

FFA[8]

Bit 8: Filter FIFO assignment for filter 8.

FFA[9]

Bit 9: Filter FIFO assignment for filter 9.

FFA[10]

Bit 10: Filter FIFO assignment for filter 10.

FFA[11]

Bit 11: Filter FIFO assignment for filter 11.

FFA[12]

Bit 12: Filter FIFO assignment for filter 12.

FFA[13]

Bit 13: Filter FIFO assignment for filter 13.

FFA[14]

Bit 14: Filter FIFO assignment for filter 14.

FFA[15]

Bit 15: Filter FIFO assignment for filter 15.

FFA[16]

Bit 16: Filter FIFO assignment for filter 16.

FFA[17]

Bit 17: Filter FIFO assignment for filter 17.

FFA[18]

Bit 18: Filter FIFO assignment for filter 18.

FFA[19]

Bit 19: Filter FIFO assignment for filter 19.

FFA[20]

Bit 20: Filter FIFO assignment for filter 20.

FFA[21]

Bit 21: Filter FIFO assignment for filter 21.

FFA[22]

Bit 22: Filter FIFO assignment for filter 22.

FFA[23]

Bit 23: Filter FIFO assignment for filter 23.

FFA[24]

Bit 24: Filter FIFO assignment for filter 24.

FFA[25]

Bit 25: Filter FIFO assignment for filter 25.

FFA[26]

Bit 26: Filter FIFO assignment for filter 26.

FFA[27]

Bit 27: Filter FIFO assignment for filter 27.

FA1R

CAN filter activation register

Offset: 0x21c, size: 32, reset: 0x00000000, access: read-write

0/28 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				FACT[27] rw	FACT[26] rw	FACT[25] rw	FACT[24] rw	FACT[23] rw	FACT[22] rw	FACT[21] rw	FACT[20] rw	FACT[19] rw	FACT[18] rw	FACT[17] rw	FACT[16] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FACT[15] rw	FACT[14] rw	FACT[13] rw	FACT[12] rw	FACT[11] rw	FACT[10] rw	FACT[9] rw	FACT[8] rw	FACT[7] rw	FACT[6] rw	FACT[5] rw	FACT[4] rw	FACT[3] rw	FACT[2] rw	FACT[1] rw	FACT[0] rw

Toggle fields

FACT[0]

Bit 0: Filter active.

FACT[1]

Bit 1: Filter active.

FACT[2]

Bit 2: Filter active.

FACT[3]

Bit 3: Filter active.

FACT[4]

Bit 4: Filter active.

FACT[5]

Bit 5: Filter active.

FACT[6]

Bit 6: Filter active.

FACT[7]

Bit 7: Filter active.

FACT[8]

Bit 8: Filter active.

FACT[9]

Bit 9: Filter active.

FACT[10]

Bit 10: Filter active.

FACT[11]

Bit 11: Filter active.

FACT[12]

Bit 12: Filter active.

FACT[13]

Bit 13: Filter active.

FACT[14]

Bit 14: Filter active.

FACT[15]

Bit 15: Filter active.

FACT[16]

Bit 16: Filter active.

FACT[17]

Bit 17: Filter active.

FACT[18]

Bit 18: Filter active.

FACT[19]

Bit 19: Filter active.

FACT[20]

Bit 20: Filter active.

FACT[21]

Bit 21: Filter active.

FACT[22]

Bit 22: Filter active.

FACT[23]

Bit 23: Filter active.

FACT[24]

Bit 24: Filter active.

FACT[25]

Bit 25: Filter active.

FACT[26]

Bit 26: Filter active.

FACT[27]

Bit 27: Filter active.

FR1 [0]

Filter bank x register 1

Offset: 0x240, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR2 [0]

Filter bank x register 2

Offset: 0x244, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR1 [1]

Filter bank x register 1

Offset: 0x248, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR2 [1]

Filter bank x register 2

Offset: 0x24c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR1 [2]

Filter bank x register 1

Offset: 0x250, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR2 [2]

Filter bank x register 2

Offset: 0x254, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR1 [3]

Filter bank x register 1

Offset: 0x258, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR2 [3]

Filter bank x register 2

Offset: 0x25c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR1 [4]

Filter bank x register 1

Offset: 0x260, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR2 [4]

Filter bank x register 2

Offset: 0x264, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR1 [5]

Filter bank x register 1

Offset: 0x268, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR2 [5]

Filter bank x register 2

Offset: 0x26c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR1 [6]

Filter bank x register 1

Offset: 0x270, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR2 [6]

Filter bank x register 2

Offset: 0x274, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR1 [7]

Filter bank x register 1

Offset: 0x278, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR2 [7]

Filter bank x register 2

Offset: 0x27c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR1 [8]

Filter bank x register 1

Offset: 0x280, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR2 [8]

Filter bank x register 2

Offset: 0x284, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR1 [9]

Filter bank x register 1

Offset: 0x288, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR2 [9]

Filter bank x register 2

Offset: 0x28c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR1 [10]

Filter bank x register 1

Offset: 0x290, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR2 [10]

Filter bank x register 2

Offset: 0x294, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR1 [11]

Filter bank x register 1

Offset: 0x298, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR2 [11]

Filter bank x register 2

Offset: 0x29c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR1 [12]

Filter bank x register 1

Offset: 0x2a0, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR2 [12]

Filter bank x register 2

Offset: 0x2a4, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR1 [13]

Filter bank x register 1

Offset: 0x2a8, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR2 [13]

Filter bank x register 2

Offset: 0x2ac, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR1 [14]

Filter bank x register 1

Offset: 0x2b0, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR2 [14]

Filter bank x register 2

Offset: 0x2b4, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR1 [15]

Filter bank x register 1

Offset: 0x2b8, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR2 [15]

Filter bank x register 2

Offset: 0x2bc, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR1 [16]

Filter bank x register 1

Offset: 0x2c0, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR2 [16]

Filter bank x register 2

Offset: 0x2c4, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR1 [17]

Filter bank x register 1

Offset: 0x2c8, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR2 [17]

Filter bank x register 2

Offset: 0x2cc, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR1 [18]

Filter bank x register 1

Offset: 0x2d0, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR2 [18]

Filter bank x register 2

Offset: 0x2d4, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR1 [19]

Filter bank x register 1

Offset: 0x2d8, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR2 [19]

Filter bank x register 2

Offset: 0x2dc, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR1 [20]

Filter bank x register 1

Offset: 0x2e0, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR2 [20]

Filter bank x register 2

Offset: 0x2e4, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR1 [21]

Filter bank x register 1

Offset: 0x2e8, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR2 [21]

Filter bank x register 2

Offset: 0x2ec, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR1 [22]

Filter bank x register 1

Offset: 0x2f0, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR2 [22]

Filter bank x register 2

Offset: 0x2f4, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR1 [23]

Filter bank x register 1

Offset: 0x2f8, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR2 [23]

Filter bank x register 2

Offset: 0x2fc, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR1 [24]

Filter bank x register 1

Offset: 0x300, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR2 [24]

Filter bank x register 2

Offset: 0x304, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR1 [25]

Filter bank x register 1

Offset: 0x308, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR2 [25]

Filter bank x register 2

Offset: 0x30c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR1 [26]

Filter bank x register 1

Offset: 0x310, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR2 [26]

Filter bank x register 2

Offset: 0x314, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR1 [27]

Filter bank x register 1

Offset: 0x318, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

FR2 [27]

Filter bank x register 2

Offset: 0x31c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB rw

Toggle fields

FB

Bits 0-31: Filter bits.

COMP

0x40010000: General purpose comparators

25/76 fields covered.

Toggle register map

Offset	Name	31	30	22	20	17	15	13	9	7	6	3	1	0
0x1c	COMP1_CSR	COMP1LOCK	COMP1OUT		COMP1_BLANKING	COMP1HYST	COMP1POL	COMP1OUTSEL			COMP1INMSEL	COMP1MODE	COMP1_INP_DAC	COMP1EN
0x20	COMP2_CSR	COMP2LOCK	COMP2OUT	COMP2INMSEL3	COMP2_BLANKING	COMP2HYST	COMP2POL	COMP2OUTSEL	COMP2WINMODE	COMP2INPSEL	COMP2INMSEL	COMP2MODE		COMP2EN
0x24	COMP3_CSR	COMP3LOCK	COMP3OUT		COMP3_BLANKING	COMP3HYST	COMP3POL	COMP3OUTSEL		COMP3INPSEL	COMP3INMSEL	COMP3MODE		COMP3EN
0x28	COMP4_CSR	COMP4LOCK	COMP4OUT	COMP4INMSEL3	COMP4_BLANKING	COMP4HYST	COMP4POL	COMP4OUTSEL	COMP4WINMODE	COMP4INPSEL	COMP4INMSEL	COMP4MODE		COMP4EN
0x2c	COMP5_CSR	COMP5LOCK	COMP5OUT		COMP5_BLANKING	COMP5HYST	COMP5POL	COMP5OUTSEL		COMP5INPSEL	COMP5INMSEL	COMP5MODE		COMP5EN
0x30	COMP6_CSR	COMP6LOCK	COMP6OUT	COMP6INMSEL3	COMP6_BLANKING	COMP6HYST	COMP6POL	COMP6OUTSEL	COMP6WINMODE	COMP6INPSEL	COMP6INMSEL	COMP6MODE		COMP6EN
0x34	COMP7_CSR	COMP7LOCK	COMP7OUT		COMP7_BLANKING	COMP7HYST	COMP7POL	COMP7OUTSEL		COMP7INPSEL	COMP7INMSEL	COMP7MODE		COMP7EN

Toggle registers

COMP1_CSR

control and status register

Offset: 0x1c, size: 32, reset: 0x00000000, access: Unspecified

1/10 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
COMP1LOCK rw	COMP1OUT r										COMP1_BLANKING rw			COMP1HYST rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
COMP1POL rw		COMP1OUTSEL rw							COMP1INMSEL rw			COMP1MODE rw		COMP1_INP_DAC rw	COMP1EN rw

Toggle fields

COMP1EN

Bit 0: Comparator 1 enable.

COMP1_INP_DAC

Bit 1: Comparator 1 non inverting input connection to DAC output.

COMP1MODE

Bits 2-3: Comparator 1 mode.

COMP1INMSEL

Bits 4-6: Comparator 1 inverting input selection.

COMP1OUTSEL

Bits 10-13: Comparator 1 output selection.

COMP1POL

Bit 15: Comparator 1 output polarity.

COMP1HYST

Bits 16-17: Comparator 1 hysteresis.

COMP1_BLANKING

Bits 18-20: Comparator 1 blanking source.

COMP1OUT

Bit 30: Comparator 1 output.

COMP1LOCK

Bit 31: Comparator 1 lock.

COMP2_CSR

control and status register

Offset: 0x20, size: 32, reset: 0x00000000, access: Unspecified

7/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
COMP2LOCK rw	COMP2OUT r								COMP2INMSEL3 rw		COMP2_BLANKING rw			COMP2HYST rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
COMP2POL rw		COMP2OUTSEL rw				COMP2WINMODE rw		COMP2INPSEL rw	COMP2INMSEL rw			COMP2MODE rw			COMP2EN rw

Toggle fields

COMP2EN

Bit 0: Comparator 2 enable.

Allowed values:
0: Disabled: Comparator disabled
1: Enabled: Comparator enabled

COMP2MODE

Bits 2-3: Comparator 2 mode.

COMP2INMSEL

Bits 4-6: Comparator 2 inverting input selection.

Allowed values:
0: OneQuarterVRef: 1/4 of VRefint
1: OneHalfVRef: 1/2 of VRefint
2: ThreeQuarterVRef: 3/4 of VRefint
3: VRef: VRefint
4: PA4_DAC1_CH1: PA4 or DAC1_CH1 output if enabled
5: DAC1_CH2: DAC1_CH2
6: PA2: PA2

COMP2INPSEL

Bit 7: Comparator 2 non inverted input.

COMP2WINMODE

Bit 9: Comparator 2 window mode.

COMP2OUTSEL

Bits 10-13: Comparator 2 output selection.

Allowed values:
0: NoSelection: No selection
1: Timer1BreakInput: Timer 1 break input
2: Timer1BreakInput2: Timer 1 break input 2
6: Timer1OCRefClearInput: Timer 1 OCREF_CLR input
7: Timer1InputCapture1: Timer 1 input capture 1
8: Timer2InputCapture4: Timer 2 input capture 4
9: Timer2OCRefClearInput: Timer 2 OCREF_CLR input
10: Timer3InputCapture1: Timer 3 input capture 1
11: Timer3OCRefClearInput: Timer 3 OCREF_CLR input

COMP2POL

Bit 15: Comparator 2 output polarity.

Allowed values:
0: NotInverted: Output is not inverted
1: Inverted: Output is inverted

COMP2HYST

Bits 16-17: Comparator 2 hysteresis.

COMP2_BLANKING

Bits 18-20: Comparator 2 blanking source.

Allowed values:
0: NoBlanking: No blanking
1: TIM1OC5: TIM1 OC5 selected as blanking source
2: TIM2OC3: TIM2 OC3 selected as blanking source
3: TIM3OC3: TIM3 OC3 selected as blanking source

COMP2INMSEL3

Bit 22: Comparator 2 inverting input selection.

COMP2OUT

Bit 30: Comparator 2 output.

Allowed values:
0: Low: Non-inverting input below inverting input
1: High: Non-inverting input above inverting input

COMP2LOCK

Bit 31: Comparator 2 lock.

Allowed values:
0: Unlocked: Comparator CSR bits are read-write
1: Locked: Comparator CSR bits are read-only

COMP3_CSR

control and status register

Offset: 0x24, size: 32, reset: 0x00000000, access: Unspecified

1/10 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
COMP3LOCK rw	COMP3OUT r										COMP3_BLANKING rw			COMP3HYST rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
COMP3POL rw		COMP3OUTSEL rw						COMP3INPSEL rw	COMP3INMSEL rw			COMP3MODE rw			COMP3EN rw

Toggle fields

COMP3EN

Bit 0: Comparator 3 enable.

COMP3MODE

Bits 2-3: Comparator 3 mode.

COMP3INMSEL

Bits 4-6: Comparator 3 inverting input selection.

COMP3INPSEL

Bit 7: Comparator 3 non inverted input.

COMP3OUTSEL

Bits 10-13: Comparator 3 output selection.

COMP3POL

Bit 15: Comparator 3 output polarity.

COMP3HYST

Bits 16-17: Comparator 3 hysteresis.

COMP3_BLANKING

Bits 18-20: Comparator 3 blanking source.

COMP3OUT

Bit 30: Comparator 3 output.

COMP3LOCK

Bit 31: Comparator 3 lock.

COMP4_CSR

control and status register

Offset: 0x28, size: 32, reset: 0x00000000, access: Unspecified

7/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
COMP4LOCK rw	COMP4OUT r								COMP4INMSEL3 rw		COMP4_BLANKING rw			COMP4HYST rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
COMP4POL rw		COMP4OUTSEL rw				COMP4WINMODE rw		COMP4INPSEL rw	COMP4INMSEL rw			COMP4MODE rw			COMP4EN rw

Toggle fields

COMP4EN

Bit 0: Comparator 4 enable.

Allowed values:
0: Disabled: Comparator disabled
1: Enabled: Comparator enabled

COMP4MODE

Bits 2-3: Comparator 4 mode.

COMP4INMSEL

Bits 4-6: Comparator 4 inverting input selection.

Allowed values:
0: OneQuarterVRef: 1/4 of VRefint
1: OneHalfVRef: 1/2 of VRefint
2: ThreeQuarterVRef: 3/4 of VRefint
3: VRef: VRefint
4: PA4_DAC1_CH1: PA4 or DAC1_CH1 output if enabled
5: DAC1_CH2: DAC1_CH2
7: PB2: PB2

COMP4INPSEL

Bit 7: Comparator 4 non inverted input.

COMP4WINMODE

Bit 9: Comparator 4 window mode.

COMP4OUTSEL

Bits 10-13: Comparator 4 output selection.

Allowed values:
0: NoSelection: No selection
1: Timer1BreakInput: Timer 1 break input
2: Timer1BreakInput2: Timer 1 break input 2
6: Timer3InputCapture3: Timer 3 input capture 3
8: Timer15InputCapture2: Timer 15 input capture 2
10: Timer15OCRefClearInput: Timer 15 OCREF_CLR input
11: Timer3OCRefClearInput: Timer 3 OCREF_CLR input

COMP4POL

Bit 15: Comparator 4 output polarity.

Allowed values:
0: NotInverted: Output is not inverted
1: Inverted: Output is inverted

COMP4HYST

Bits 16-17: Comparator 4 hysteresis.

COMP4_BLANKING

Bits 18-20: Comparator 4 blanking source.

Allowed values:
0: NoBlanking: No blanking
1: TIM3OC4: TIM3 OC4 selected as blanking source
3: TIM15OC1: TIM15 OC1 selected as blanking source

COMP4INMSEL3

Bit 22: Comparator 4 inverting input selection.

COMP4OUT

Bit 30: Comparator 4 output.

Allowed values:
0: Low: Non-inverting input below inverting input
1: High: Non-inverting input above inverting input

COMP4LOCK

Bit 31: Comparator 4 lock.

Allowed values:
0: Unlocked: Comparator CSR bits are read-write
1: Locked: Comparator CSR bits are read-only

COMP5_CSR

control and status register

Offset: 0x2c, size: 32, reset: 0x00000000, access: Unspecified

1/10 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
COMP5LOCK rw	COMP5OUT r										COMP5_BLANKING rw			COMP5HYST rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
COMP5POL rw		COMP5OUTSEL rw						COMP5INPSEL rw	COMP5INMSEL rw			COMP5MODE rw			COMP5EN rw

Toggle fields

COMP5EN

Bit 0: Comparator 5 enable.

COMP5MODE

Bits 2-3: Comparator 5 mode.

COMP5INMSEL

Bits 4-6: Comparator 5 inverting input selection.

COMP5INPSEL

Bit 7: Comparator 5 non inverted input.

COMP5OUTSEL

Bits 10-13: Comparator 5 output selection.

COMP5POL

Bit 15: Comparator 5 output polarity.

COMP5HYST

Bits 16-17: Comparator 5 hysteresis.

COMP5_BLANKING

Bits 18-20: Comparator 5 blanking source.

COMP5OUT

Bit 30: Comparator 5 output.

COMP5LOCK

Bit 31: Comparator 5 lock.

COMP6_CSR

control and status register

Offset: 0x30, size: 32, reset: 0x00000000, access: Unspecified

7/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
COMP6LOCK rw	COMP6OUT r								COMP6INMSEL3 rw		COMP6_BLANKING rw			COMP6HYST rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
COMP6POL rw		COMP6OUTSEL rw				COMP6WINMODE rw		COMP6INPSEL rw	COMP6INMSEL rw			COMP6MODE rw			COMP6EN rw

Toggle fields

COMP6EN

Bit 0: Comparator 6 enable.

Allowed values:
0: Disabled: Comparator disabled
1: Enabled: Comparator enabled

COMP6MODE

Bits 2-3: Comparator 6 mode.

COMP6INMSEL

Bits 4-6: Comparator 6 inverting input selection.

Allowed values:
0: OneQuarterVRef: 1/4 of VRefint
1: OneHalfVRef: 1/2 of VRefint
2: ThreeQuarterVRef: 3/4 of VRefint
3: VRef: VRefint
4: PA4_DAC1_CH1: PA4 or DAC1_CH1 output if enabled
5: DAC1_CH2: DAC1_CH2
7: PB15: PB15

COMP6INPSEL

Bit 7: Comparator 6 non inverted input.

COMP6WINMODE

Bit 9: Comparator 6 window mode.

COMP6OUTSEL

Bits 10-13: Comparator 6 output selection.

Allowed values:
0: NoSelection: No selection
1: Timer1BreakInput: Timer 1 break input
2: Timer1BreakInput2: Timer 1 break input 2
6: Timer2InputCapture2: Timer 2 input capture 2
8: Timer2OCRefClearInput: Timer 2 OCREF_CLR input
9: Timer16OCRefClearInput: Timer 16 OCREF_CLR input
10: Timer16InputCapture1: Timer 16 input capture 1

COMP6POL

Bit 15: Comparator 6 output polarity.

Allowed values:
0: NotInverted: Output is not inverted
1: Inverted: Output is inverted

COMP6HYST

Bits 16-17: Comparator 6 hysteresis.

COMP6_BLANKING

Bits 18-20: Comparator 6 blanking source.

Allowed values:
0: NoBlanking: No blanking
3: TIM2OC4: TIM2 OC4 selected as blanking source
4: TIM15OC2: TIM15 OC2 selected as blanking source

COMP6INMSEL3

Bit 22: Comparator 6 inverting input selection.

COMP6OUT

Bit 30: Comparator 6 output.

Allowed values:
0: Low: Non-inverting input below inverting input
1: High: Non-inverting input above inverting input

COMP6LOCK

Bit 31: Comparator 6 lock.

Allowed values:
0: Unlocked: Comparator CSR bits are read-write
1: Locked: Comparator CSR bits are read-only

COMP7_CSR

control and status register

Offset: 0x34, size: 32, reset: 0x00000000, access: Unspecified

1/10 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
COMP7LOCK rw	COMP7OUT r										COMP7_BLANKING rw			COMP7HYST rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
COMP7POL rw		COMP7OUTSEL rw						COMP7INPSEL rw	COMP7INMSEL rw			COMP7MODE rw			COMP7EN rw

Toggle fields

COMP7EN

Bit 0: Comparator 7 enable.

COMP7MODE

Bits 2-3: Comparator 7 mode.

COMP7INMSEL

Bits 4-6: Comparator 7 inverting input selection.

COMP7INPSEL

Bit 7: Comparator 7 non inverted input.

COMP7OUTSEL

Bits 10-13: Comparator 7 output selection.

COMP7POL

Bit 15: Comparator 7 output polarity.

COMP7HYST

Bits 16-17: Comparator 7 hysteresis.

COMP7_BLANKING

Bits 18-20: Comparator 7 blanking source.

COMP7OUT

Bit 30: Comparator 7 output.

COMP7LOCK

Bit 31: Comparator 7 lock.

CRC

0x40023000: cyclic redundancy check calculation unit

10/10 fields covered.

Toggle register map

Offset	Name	31	15	7	6	4	0
0x0	DR	DR	DR
0x0 (16-bit)	DR16		DR16
0x0 (8-bit)	DR8			DR8
0x4	IDR			IDR
0x8	CR			REV_OUT	REV_IN	POLYSIZE	RESET
0x10	INIT	INIT	INIT
0x14	POL	POL	POL

Toggle registers

DR

Data register

Offset: 0x0, size: 32, reset: 0xFFFFFFFF, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
DR rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DR rw

Toggle fields

DR

Bits 0-31: Data register bits.

Allowed values: 0x0-0xffffffff

DR16

Data register - half-word sized

Offset: 0x0, size: 16, reset: 0x0000FFFF, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DR16 rw

Toggle fields

DR16

Bits 0-15: Data register bits.

Allowed values: 0x0-0xffff

DR8

Data register - byte sized

Offset: 0x0, size: 8, reset: 0x000000FF, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								DR8 rw

Toggle fields

DR8

Bits 0-7: Data register bits.

Allowed values: 0x0-0xff

IDR

Independent data register

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								IDR rw

Toggle fields

IDR

Bits 0-7: General-purpose 8-bit data register bits.

Allowed values: 0x0-0xff

CR

Control register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

4/4 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								REV_OUT rw	REV_IN rw		POLYSIZE rw				RESET rw

Toggle fields

RESET

Bit 0: reset bit.

Allowed values:
1: Reset: Resets the CRC calculation unit and sets the data register to 0xFFFF FFFF

POLYSIZE

Bits 3-4: Polynomial size.

Allowed values:
0: Polysize32: 32-bit polynomial
1: Polysize16: 16-bit polynomial
2: Polysize8: 8-bit polynomial
3: Polysize7: 7-bit polynomial

REV_IN

Bits 5-6: Reverse input data.

Allowed values:
0: Normal: Bit order not affected
1: Byte: Bit reversal done by byte
2: HalfWord: Bit reversal done by half-word
3: Word: Bit reversal done by word

REV_OUT

Bit 7: Reverse output data.

Allowed values:
0: Normal: Bit order not affected
1: Reversed: Bit reversed output

INIT

Initial CRC value

Offset: 0x10, size: 32, reset: 0xFFFFFFFF, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
INIT rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
INIT rw

Toggle fields

INIT

Bits 0-31: Programmable initial CRC value.

Allowed values: 0x0-0xffffffff

POL

CRC polynomial

Offset: 0x14, size: 32, reset: 0x04C11DB7, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
POL rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
POL rw

Toggle fields

POL

Bits 0-31: Programmable polynomial.

Allowed values: 0x0-0xffffffff

DAC1

0x40007400: Digital-to-analog converter

34/34 fields covered.

Toggle register map

Offset	Name	31	29	28	27	23	21	18	17	16	15	13	12	11	7	5	2	1	0
0x0	CR		DMAUDRIE2	DMAEN2	MAMP2	WAVE2	TSEL2	TEN2	BOFF2	EN2		DMAUDRIE1	DMAEN1	MAMP1	WAVE1	TSEL1	TEN1	BOFF1	EN1
0x4	SWTRIGR																	SWTRIG2	SWTRIG1
0x8	DHR12R1													DACC1DHR
0xc	DHR12L1										DACC1DHR
0x10	DHR8R1														DACC1DHR
0x14	DHR12R2													DACC2DHR
0x18	DHR12L2										DACC2DHR
0x1c	DHR8R2														DACC2DHR
0x20	DHR12RD				DACC2DHR									DACC1DHR
0x24	DHR12LD	DACC2DHR									DACC1DHR
0x28	DHR8RD										DACC2DHR				DACC1DHR
0x2c	DOR1													DACC1DOR
0x30	DOR2													DACC2DOR
0x34	SR		DMAUDR2									DMAUDR1

Toggle registers

CR

control register

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
		DMAUDRIE2 rw	DMAEN2 rw	MAMP2 rw				WAVE2 rw		TSEL2 rw			TEN2 rw	BOFF2 rw	EN2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		DMAUDRIE1 rw	DMAEN1 rw	MAMP1 rw				WAVE1 rw		TSEL1 rw			TEN1 rw	BOFF1 rw	EN1 rw

Toggle fields

EN1

Bit 0: DAC channel1 enable.

Allowed values:
0: Disabled: DAC channel X disabled
1: Enabled: DAC channel X enabled

BOFF1

Bit 1: DAC channel1 output buffer disable.

Allowed values:
0: Enabled: DAC channel X output buffer enabled
1: Disabled: DAC channel X output buffer disabled

TEN1

Bit 2: DAC channel1 trigger enable.

Allowed values:
0: Disabled: DAC channel X trigger disabled
1: Enabled: DAC channel X trigger enabled

TSEL1

Bits 3-5: DAC channel1 trigger selection.

Allowed values:
0: TIM6_TRGO: Timer 6 TRGO event
1: TIM3_TRGO: Timer 3 TRGO event
2: TIM7_TRGO: Timer 7 TRGO event
3: TIM15_TRGO: Timer 15 TRGO event
4: TIM2_TRGO: Timer 2 TRGO event
6: EXTI9: EXTI line9
7: SOFTWARE: Software trigger

WAVE1

Bits 6-7: DAC channel1 noise/triangle wave generation enable.

Allowed values:
0: Disabled: Wave generation disabled
1: Noise: Noise wave generation enabled
2: Triangle: Triangle wave generation enabled

MAMP1

Bits 8-11: DAC channel1 mask/amplitude selector.

Allowed values: 0x0-0xf

DMAEN1

Bit 12: DAC channel1 DMA enable.

Allowed values:
0: Disabled: DAC channel X DMA mode disabled
1: Enabled: DAC channel X DMA mode enabled

DMAUDRIE1

Bit 13: DAC channel1 DMA Underrun Interrupt enable.

Allowed values:
0: Disabled: DAC channel X DMA Underrun Interrupt disabled
1: Enabled: DAC channel X DMA Underrun Interrupt enabled

EN2

Bit 16: DAC channel2 enable.

Allowed values:
0: Disabled: DAC channel X disabled
1: Enabled: DAC channel X enabled

BOFF2

Bit 17: DAC channel2 output buffer disable.

Allowed values:
0: Enabled: DAC channel X output buffer enabled
1: Disabled: DAC channel X output buffer disabled

TEN2

Bit 18: DAC channel2 trigger enable.

Allowed values:
0: Disabled: DAC channel X trigger disabled
1: Enabled: DAC channel X trigger enabled

TSEL2

Bits 19-21: DAC channel2 trigger selection.

Allowed values:
0: TIM6_TRGO: Timer 6 TRGO event
1: TIM8_TRGO: Timer 8 TRGO event
2: TIM7_TRGO: Timer 7 TRGO event
3: TIM5_TRGO: Timer 5 TRGO event
4: TIM2_TRGO: Timer 2 TRGO event
5: TIM4_TRGO: Timer 4 TRGO event
6: EXTI9: EXTI line9
7: SOFTWARE: Software trigger

WAVE2

Bits 22-23: DAC channel2 noise/triangle wave generation enable.

Allowed values:
0: Disabled: Wave generation disabled
1: Noise: Noise wave generation enabled
2: Triangle: Triangle wave generation enabled

MAMP2

Bits 24-27: DAC channel2 mask/amplitude selector.

Allowed values: 0x0-0xf

DMAEN2

Bit 28: DAC channel2 DMA enable.

Allowed values:
0: Disabled: DAC channel X DMA mode disabled
1: Enabled: DAC channel X DMA mode enabled

DMAUDRIE2

Bit 29: DAC channel2 DMA underrun interrupt enable.

Allowed values:
0: Disabled: DAC channel X DMA Underrun Interrupt disabled
1: Enabled: DAC channel X DMA Underrun Interrupt enabled

SWTRIGR

software trigger register

Offset: 0x4, size: 32, reset: 0x00000000, access: write-only

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														SWTRIG2 w	SWTRIG1 w

Toggle fields

SWTRIG1

Bit 0: DAC channel1 software trigger.

Allowed values:
0: Disabled: DAC channel X software trigger disabled
1: Enabled: DAC channel X software trigger enabled

SWTRIG2

Bit 1: DAC channel2 software trigger.

Allowed values:
0: Disabled: DAC channel X software trigger disabled
1: Enabled: DAC channel X software trigger enabled

DHR12R1

channel1 12-bit right-aligned data holding register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				DACC1DHR rw

Toggle fields

DACC1DHR

Bits 0-11: DAC channel1 12-bit right-aligned data.

Allowed values: 0x0-0xfff

DHR12L1

channel1 12-bit left aligned data holding register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DACC1DHR rw

Toggle fields

DACC1DHR

Bits 4-15: DAC channel1 12-bit left-aligned data.

Allowed values: 0x0-0xfff

DHR8R1

channel1 8-bit right aligned data holding register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								DACC1DHR rw

Toggle fields

DACC1DHR

Bits 0-7: DAC channel1 8-bit right-aligned data.

Allowed values: 0x0-0xff

DHR12R2

channel2 12-bit right aligned data holding register

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				DACC2DHR rw

Toggle fields

DACC2DHR

Bits 0-11: DAC channel2 12-bit right-aligned data.

Allowed values: 0x0-0xfff

DHR12L2

channel2 12-bit left aligned data holding register

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DACC2DHR rw

Toggle fields

DACC2DHR

Bits 4-15: DAC channel2 12-bit left-aligned data.

Allowed values: 0x0-0xfff

DHR8R2

channel2 8-bit right-aligned data holding register

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								DACC2DHR rw

Toggle fields

DACC2DHR

Bits 0-7: DAC channel2 8-bit right-aligned data.

Allowed values: 0x0-0xff

DHR12RD

Dual DAC 12-bit right-aligned data holding register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				DACC2DHR rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				DACC1DHR rw

Toggle fields

DACC1DHR

Bits 0-11: DAC channel1 12-bit right-aligned data.

Allowed values: 0x0-0xfff

DACC2DHR

Bits 16-27: DAC channel2 12-bit right-aligned data.

Allowed values: 0x0-0xfff

DHR12LD

DUAL DAC 12-bit left aligned data holding register

Offset: 0x24, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
DACC2DHR rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DACC1DHR rw

Toggle fields

DACC1DHR

Bits 4-15: DAC channel1 12-bit left-aligned data.

Allowed values: 0x0-0xfff

DACC2DHR

Bits 20-31: DAC channel2 12-bit left-aligned data.

Allowed values: 0x0-0xfff

DHR8RD

DUAL DAC 8-bit right aligned data holding register

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DACC2DHR rw								DACC1DHR rw

Toggle fields

DACC1DHR

Bits 0-7: DAC channel1 8-bit right-aligned data.

Allowed values: 0x0-0xff

DACC2DHR

Bits 8-15: DAC channel2 8-bit right-aligned data.

Allowed values: 0x0-0xff

DOR1

channel1 data output register

Offset: 0x2c, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				DACC1DOR r

Toggle fields

DACC1DOR

Bits 0-11: DAC channel1 data output.

DOR2

channel2 data output register

Offset: 0x30, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				DACC2DOR r

Toggle fields

DACC2DOR

Bits 0-11: DAC channel2 data output.

SR

status register

Offset: 0x34, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
		DMAUDR2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		DMAUDR1 rw

Toggle fields

DMAUDR1

Bit 13: DAC channel1 DMA underrun flag.

Allowed values:
0: NoUnderrun: No DMA underrun error condition occurred for DAC channel X
1: Underrun: DMA underrun error condition occurred for DAC channel X

DMAUDR2

Bit 29: DAC channel2 DMA underrun flag.

Allowed values:
0: NoUnderrun: No DMA underrun error condition occurred for DAC channel X
1: Underrun: DMA underrun error condition occurred for DAC channel X

DAC2

0x40009800: Digital-to-analog converter

34/34 fields covered.

Toggle register map

Offset	Name	31	29	28	27	23	21	18	17	16	15	13	12	11	7	5	2	1	0
0x0	CR		DMAUDRIE2	DMAEN2	MAMP2	WAVE2	TSEL2	TEN2	BOFF2	EN2		DMAUDRIE1	DMAEN1	MAMP1	WAVE1	TSEL1	TEN1	BOFF1	EN1
0x4	SWTRIGR																	SWTRIG2	SWTRIG1
0x8	DHR12R1													DACC1DHR
0xc	DHR12L1										DACC1DHR
0x10	DHR8R1														DACC1DHR
0x14	DHR12R2													DACC2DHR
0x18	DHR12L2										DACC2DHR
0x1c	DHR8R2														DACC2DHR
0x20	DHR12RD				DACC2DHR									DACC1DHR
0x24	DHR12LD	DACC2DHR									DACC1DHR
0x28	DHR8RD										DACC2DHR				DACC1DHR
0x2c	DOR1													DACC1DOR
0x30	DOR2													DACC2DOR
0x34	SR		DMAUDR2									DMAUDR1

Toggle registers

CR

control register

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
		DMAUDRIE2 rw	DMAEN2 rw	MAMP2 rw				WAVE2 rw		TSEL2 rw			TEN2 rw	BOFF2 rw	EN2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		DMAUDRIE1 rw	DMAEN1 rw	MAMP1 rw				WAVE1 rw		TSEL1 rw			TEN1 rw	BOFF1 rw	EN1 rw

Toggle fields

EN1

Bit 0: DAC channel1 enable.

Allowed values:
0: Disabled: DAC channel X disabled
1: Enabled: DAC channel X enabled

BOFF1

Bit 1: DAC channel1 output buffer disable.

Allowed values:
0: Enabled: DAC channel X output buffer enabled
1: Disabled: DAC channel X output buffer disabled

TEN1

Bit 2: DAC channel1 trigger enable.

Allowed values:
0: Disabled: DAC channel X trigger disabled
1: Enabled: DAC channel X trigger enabled

TSEL1

Bits 3-5: DAC channel1 trigger selection.

Allowed values:
0: TIM6_TRGO: Timer 6 TRGO event
1: TIM3_TRGO: Timer 3 TRGO event
2: TIM7_TRGO: Timer 7 TRGO event
3: TIM15_TRGO: Timer 15 TRGO event
4: TIM2_TRGO: Timer 2 TRGO event
6: EXTI9: EXTI line9
7: SOFTWARE: Software trigger

WAVE1

Bits 6-7: DAC channel1 noise/triangle wave generation enable.

Allowed values:
0: Disabled: Wave generation disabled
1: Noise: Noise wave generation enabled
2: Triangle: Triangle wave generation enabled

MAMP1

Bits 8-11: DAC channel1 mask/amplitude selector.

Allowed values: 0x0-0xf

DMAEN1

Bit 12: DAC channel1 DMA enable.

Allowed values:
0: Disabled: DAC channel X DMA mode disabled
1: Enabled: DAC channel X DMA mode enabled

DMAUDRIE1

Bit 13: DAC channel1 DMA Underrun Interrupt enable.

Allowed values:
0: Disabled: DAC channel X DMA Underrun Interrupt disabled
1: Enabled: DAC channel X DMA Underrun Interrupt enabled

EN2

Bit 16: DAC channel2 enable.

Allowed values:
0: Disabled: DAC channel X disabled
1: Enabled: DAC channel X enabled

BOFF2

Bit 17: DAC channel2 output buffer disable.

Allowed values:
0: Enabled: DAC channel X output buffer enabled
1: Disabled: DAC channel X output buffer disabled

TEN2

Bit 18: DAC channel2 trigger enable.

Allowed values:
0: Disabled: DAC channel X trigger disabled
1: Enabled: DAC channel X trigger enabled

TSEL2

Bits 19-21: DAC channel2 trigger selection.

Allowed values:
0: TIM6_TRGO: Timer 6 TRGO event
1: TIM8_TRGO: Timer 8 TRGO event
2: TIM7_TRGO: Timer 7 TRGO event
3: TIM5_TRGO: Timer 5 TRGO event
4: TIM2_TRGO: Timer 2 TRGO event
5: TIM4_TRGO: Timer 4 TRGO event
6: EXTI9: EXTI line9
7: SOFTWARE: Software trigger

WAVE2

Bits 22-23: DAC channel2 noise/triangle wave generation enable.

Allowed values:
0: Disabled: Wave generation disabled
1: Noise: Noise wave generation enabled
2: Triangle: Triangle wave generation enabled

MAMP2

Bits 24-27: DAC channel2 mask/amplitude selector.

Allowed values: 0x0-0xf

DMAEN2

Bit 28: DAC channel2 DMA enable.

Allowed values:
0: Disabled: DAC channel X DMA mode disabled
1: Enabled: DAC channel X DMA mode enabled

DMAUDRIE2

Bit 29: DAC channel2 DMA underrun interrupt enable.

Allowed values:
0: Disabled: DAC channel X DMA Underrun Interrupt disabled
1: Enabled: DAC channel X DMA Underrun Interrupt enabled

SWTRIGR

software trigger register

Offset: 0x4, size: 32, reset: 0x00000000, access: write-only

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														SWTRIG2 w	SWTRIG1 w

Toggle fields

SWTRIG1

Bit 0: DAC channel1 software trigger.

Allowed values:
0: Disabled: DAC channel X software trigger disabled
1: Enabled: DAC channel X software trigger enabled

SWTRIG2

Bit 1: DAC channel2 software trigger.

Allowed values:
0: Disabled: DAC channel X software trigger disabled
1: Enabled: DAC channel X software trigger enabled

DHR12R1

channel1 12-bit right-aligned data holding register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				DACC1DHR rw

Toggle fields

DACC1DHR

Bits 0-11: DAC channel1 12-bit right-aligned data.

Allowed values: 0x0-0xfff

DHR12L1

channel1 12-bit left aligned data holding register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DACC1DHR rw

Toggle fields

DACC1DHR

Bits 4-15: DAC channel1 12-bit left-aligned data.

Allowed values: 0x0-0xfff

DHR8R1

channel1 8-bit right aligned data holding register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								DACC1DHR rw

Toggle fields

DACC1DHR

Bits 0-7: DAC channel1 8-bit right-aligned data.

Allowed values: 0x0-0xff

DHR12R2

channel2 12-bit right aligned data holding register

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				DACC2DHR rw

Toggle fields

DACC2DHR

Bits 0-11: DAC channel2 12-bit right-aligned data.

Allowed values: 0x0-0xfff

DHR12L2

channel2 12-bit left aligned data holding register

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DACC2DHR rw

Toggle fields

DACC2DHR

Bits 4-15: DAC channel2 12-bit left-aligned data.

Allowed values: 0x0-0xfff

DHR8R2

channel2 8-bit right-aligned data holding register

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								DACC2DHR rw

Toggle fields

DACC2DHR

Bits 0-7: DAC channel2 8-bit right-aligned data.

Allowed values: 0x0-0xff

DHR12RD

Dual DAC 12-bit right-aligned data holding register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				DACC2DHR rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				DACC1DHR rw

Toggle fields

DACC1DHR

Bits 0-11: DAC channel1 12-bit right-aligned data.

Allowed values: 0x0-0xfff

DACC2DHR

Bits 16-27: DAC channel2 12-bit right-aligned data.

Allowed values: 0x0-0xfff

DHR12LD

DUAL DAC 12-bit left aligned data holding register

Offset: 0x24, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
DACC2DHR rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DACC1DHR rw

Toggle fields

DACC1DHR

Bits 4-15: DAC channel1 12-bit left-aligned data.

Allowed values: 0x0-0xfff

DACC2DHR

Bits 20-31: DAC channel2 12-bit left-aligned data.

Allowed values: 0x0-0xfff

DHR8RD

DUAL DAC 8-bit right aligned data holding register

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DACC2DHR rw								DACC1DHR rw

Toggle fields

DACC1DHR

Bits 0-7: DAC channel1 8-bit right-aligned data.

Allowed values: 0x0-0xff

DACC2DHR

Bits 8-15: DAC channel2 8-bit right-aligned data.

Allowed values: 0x0-0xff

DOR1

channel1 data output register

Offset: 0x2c, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				DACC1DOR r

Toggle fields

DACC1DOR

Bits 0-11: DAC channel1 data output.

DOR2

channel2 data output register

Offset: 0x30, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				DACC2DOR r

Toggle fields

DACC2DOR

Bits 0-11: DAC channel2 data output.

SR

status register

Offset: 0x34, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
		DMAUDR2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		DMAUDR1 rw

Toggle fields

DMAUDR1

Bit 13: DAC channel1 DMA underrun flag.

Allowed values:
0: NoUnderrun: No DMA underrun error condition occurred for DAC channel X
1: Underrun: DMA underrun error condition occurred for DAC channel X

DMAUDR2

Bit 29: DAC channel2 DMA underrun flag.

Allowed values:
0: NoUnderrun: No DMA underrun error condition occurred for DAC channel X
1: Underrun: DMA underrun error condition occurred for DAC channel X

DBGMCU

0xe0042000: Debug support

2/27 fields covered.

Toggle register map

Offset	Name	31	25	22	21	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	IDCODE	REV_ID					DEV_ID
0x4	CR										TRACE_MODE		TRACE_IOEN			DBG_STANDBY	DBG_STOP	DBG_SLEEP
0x8	APB1_FZ		DBG_CAN_STOP	I2C2_SMBUS_TIMEOUT	I2C1_SMBUS_TIMEOUT	DBG_IWDG_STOP	DBG_WWDG_STOP	DBG_RTC_STOP	DBG_TIM18_STOP	DBG_TIMER14_STOP	DBG_TIM13_STOP	DBG_TIM12_STOP	DBG_TIM7_STOP	DBG_TIM6_STOP	DBG_TIM5_STOP	DBG_TIM4_STOP	DBG_TIM3_STOP	DBG_TIM2_STOP
0xc	APB2_FZ												DBG_TIM19_STOP	DBG_TIM17_STO	DBG_TIM16_STOP	DBG_TIM15_STOP

Toggle registers

IDCODE

MCU Device ID Code Register

Offset: 0x0, size: 32, reset: 0x00000000, access: read-only

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
REV_ID r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				DEV_ID r

Toggle fields

DEV_ID

Bits 0-11: Device Identifier.

REV_ID

Bits 16-31: Revision Identifier.

CR

Debug MCU Configuration Register

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

0/5 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								TRACE_MODE rw		TRACE_IOEN rw			DBG_STANDBY rw	DBG_STOP rw	DBG_SLEEP rw

Toggle fields

DBG_SLEEP

Bit 0: Debug Sleep mode.

DBG_STOP

Bit 1: Debug Stop Mode.

DBG_STANDBY

Bit 2: Debug Standby Mode.

TRACE_IOEN

Bit 5: Trace pin assignment control.

TRACE_MODE

Bits 6-7: Trace pin assignment control.

APB1_FZ

APB Low Freeze Register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

0/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
						DBG_CAN_STOP rw			I2C2_SMBUS_TIMEOUT rw	I2C1_SMBUS_TIMEOUT rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			DBG_IWDG_STOP rw	DBG_WWDG_STOP rw	DBG_RTC_STOP rw	DBG_TIM18_STOP rw	DBG_TIMER14_STOP rw	DBG_TIM13_STOP rw	DBG_TIM12_STOP rw	DBG_TIM7_STOP rw	DBG_TIM6_STOP rw	DBG_TIM5_STOP rw	DBG_TIM4_STOP rw	DBG_TIM3_STOP rw	DBG_TIM2_STOP rw

Toggle fields

DBG_TIM2_STOP

Bit 0: Debug Timer 2 stopped when Core is halted.

DBG_TIM3_STOP

Bit 1: Debug Timer 3 stopped when Core is halted.

DBG_TIM4_STOP

Bit 2: Debug Timer 4 stopped when Core is halted.

DBG_TIM5_STOP

Bit 3: Debug Timer 5 stopped when Core is halted.

DBG_TIM6_STOP

Bit 4: Debug Timer 6 stopped when Core is halted.

DBG_TIM7_STOP

Bit 5: Debug Timer 7 stopped when Core is halted.

DBG_TIM12_STOP

Bit 6: Debug Timer 12 stopped when Core is halted.

DBG_TIM13_STOP

Bit 7: Debug Timer 13 stopped when Core is halted.

DBG_TIMER14_STOP

Bit 8: Debug Timer 14 stopped when Core is halted.

DBG_TIM18_STOP

Bit 9: Debug Timer 18 stopped when Core is halted.

DBG_RTC_STOP

Bit 10: Debug RTC stopped when Core is halted.

DBG_WWDG_STOP

Bit 11: Debug Window Wachdog stopped when Core is halted.

DBG_IWDG_STOP

Bit 12: Debug Independent Wachdog stopped when Core is halted.

I2C1_SMBUS_TIMEOUT

Bit 21: SMBUS timeout mode stopped when Core is halted.

I2C2_SMBUS_TIMEOUT

Bit 22: SMBUS timeout mode stopped when Core is halted.

DBG_CAN_STOP

Bit 25: Debug CAN stopped when core is halted.

APB2_FZ

APB High Freeze Register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
										DBG_TIM19_STOP rw	DBG_TIM17_STO rw	DBG_TIM16_STOP rw	DBG_TIM15_STOP rw

Toggle fields

DBG_TIM15_STOP

Bit 2: Debug Timer 15 stopped when Core is halted.

DBG_TIM16_STOP

Bit 3: Debug Timer 16 stopped when Core is halted.

DBG_TIM17_STO

Bit 4: Debug Timer 17 stopped when Core is halted.

DBG_TIM19_STOP

Bit 5: Debug Timer 19 stopped when Core is halted.

DMA1

0x40020000: DMA controller 1

147/161 fields covered.

Toggle register map

Offset	Name	31	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	ISR		TEIF[7]	HTIF[7]	TCIF[7]	GIF[7]	TEIF[6]	HTIF[6]	TCIF[6]	GIF[6]	TEIF[5]	HTIF[5]	TCIF[5]	GIF[5]	TEIF[4]	HTIF[4]	TCIF[4]	GIF[4]	TEIF[3]	HTIF[3]	TCIF[3]	GIF[3]	TEIF[2]	HTIF[2]	TCIF[2]	GIF[2]	TEIF[1]	HTIF[1]	TCIF[1]	GIF[1]
0x4	IFCR		CTEIF[7]	CHTIF[7]	CTCIF[7]	CGIF[7]	CTEIF[6]	CHTIF[6]	CTCIF[6]	CGIF[6]	CTEIF[5]	CHTIF[5]	CTCIF[5]	CGIF[5]	CTEIF[4]	CHTIF[4]	CTCIF[4]	CGIF[4]	CTEIF[3]	CHTIF[3]	CTCIF[3]	CGIF[3]	CTEIF[2]	CHTIF[2]	CTCIF[2]	CGIF[2]	CTEIF[1]	CHTIF[1]	CTCIF[1]	CGIF[1]
0x8	CR [1]															MEM2MEM	PL		MSIZE		PSIZE		MINC	PINC	CIRC	DIR	TEIE	HTIE	TCIE	EN
0xc	NDTR [1]														NDT
0x10	PAR [1]	PA													PA
0x14	MAR [1]	MA													MA
0x1c	CR [2]															MEM2MEM	PL		MSIZE		PSIZE		MINC	PINC	CIRC	DIR	TEIE	HTIE	TCIE	EN
0x20	NDTR [2]														NDT
0x24	PAR [2]	PA													PA
0x28	MAR [2]	MA													MA
0x30	CR [3]															MEM2MEM	PL		MSIZE		PSIZE		MINC	PINC	CIRC	DIR	TEIE	HTIE	TCIE	EN
0x34	NDTR [3]														NDT
0x38	PAR [3]	PA													PA
0x3c	MAR [3]	MA													MA
0x44	CR [4]															MEM2MEM	PL		MSIZE		PSIZE		MINC	PINC	CIRC	DIR	TEIE	HTIE	TCIE	EN
0x48	NDTR [4]														NDT
0x4c	PAR [4]	PA													PA
0x50	MAR [4]	MA													MA
0x58	CR [5]															MEM2MEM	PL		MSIZE		PSIZE		MINC	PINC	CIRC	DIR	TEIE	HTIE	TCIE	EN
0x5c	NDTR [5]														NDT
0x60	PAR [5]	PA													PA
0x64	MAR [5]	MA													MA
0x6c	CR [6]															MEM2MEM	PL		MSIZE		PSIZE		MINC	PINC	CIRC	DIR	TEIE	HTIE	TCIE	EN
0x70	NDTR [6]														NDT
0x74	PAR [6]	PA													PA
0x78	MAR [6]	MA													MA
0x80	CR [7]															MEM2MEM	PL		MSIZE		PSIZE		MINC	PINC	CIRC	DIR	TEIE	HTIE	TCIE	EN
0x84	NDTR [7]														NDT
0x88	PAR [7]	PA													PA
0x8c	MAR [7]	MA													MA

Toggle registers

ISR

DMA interrupt status register (DMA_ISR)

Offset: 0x0, size: 32, reset: 0x00000000, access: read-only

28/28 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				TEIF[7] r	HTIF[7] r	TCIF[7] r	GIF[7] r	TEIF[6] r	HTIF[6] r	TCIF[6] r	GIF[6] r	TEIF[5] r	HTIF[5] r	TCIF[5] r	GIF[5] r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TEIF[4] r	HTIF[4] r	TCIF[4] r	GIF[4] r	TEIF[3] r	HTIF[3] r	TCIF[3] r	GIF[3] r	TEIF[2] r	HTIF[2] r	TCIF[2] r	GIF[2] r	TEIF[1] r	HTIF[1] r	TCIF[1] r	GIF[1] r

Toggle fields

GIF[1]

Bit 0: Channel 1 Global interrupt flag.

Allowed values:
0: NoEvent: No transfer error, half event, complete event
1: Event: A transfer error, half event or complete event has occured

TCIF[1]

Bit 1: Channel 1 Transfer Complete flag.

Allowed values:
0: NotComplete: No transfer complete event
1: Complete: A transfer complete event has occured

HTIF[1]

Bit 2: Channel 1 Half Transfer Complete flag.

Allowed values:
0: NotHalf: No half transfer event
1: Half: A half transfer event has occured

TEIF[1]

Bit 3: Channel 1 Transfer Error flag.

Allowed values:
0: NoError: No transfer error
1: Error: A transfer error has occured

GIF[2]

Bit 4: Channel 2 Global interrupt flag.

Allowed values:
0: NoEvent: No transfer error, half event, complete event
1: Event: A transfer error, half event or complete event has occured

TCIF[2]

Bit 5: Channel 2 Transfer Complete flag.

Allowed values:
0: NotComplete: No transfer complete event
1: Complete: A transfer complete event has occured

HTIF[2]

Bit 6: Channel 2 Half Transfer Complete flag.

Allowed values:
0: NotHalf: No half transfer event
1: Half: A half transfer event has occured

TEIF[2]

Bit 7: Channel 2 Transfer Error flag.

Allowed values:
0: NoError: No transfer error
1: Error: A transfer error has occured

GIF[3]

Bit 8: Channel 3 Global interrupt flag.

Allowed values:
0: NoEvent: No transfer error, half event, complete event
1: Event: A transfer error, half event or complete event has occured

TCIF[3]

Bit 9: Channel 3 Transfer Complete flag.

Allowed values:
0: NotComplete: No transfer complete event
1: Complete: A transfer complete event has occured

HTIF[3]

Bit 10: Channel 3 Half Transfer Complete flag.

Allowed values:
0: NotHalf: No half transfer event
1: Half: A half transfer event has occured

TEIF[3]

Bit 11: Channel 3 Transfer Error flag.

Allowed values:
0: NoError: No transfer error
1: Error: A transfer error has occured

GIF[4]

Bit 12: Channel 4 Global interrupt flag.

Allowed values:
0: NoEvent: No transfer error, half event, complete event
1: Event: A transfer error, half event or complete event has occured

TCIF[4]

Bit 13: Channel 4 Transfer Complete flag.

Allowed values:
0: NotComplete: No transfer complete event
1: Complete: A transfer complete event has occured

HTIF[4]

Bit 14: Channel 4 Half Transfer Complete flag.

Allowed values:
0: NotHalf: No half transfer event
1: Half: A half transfer event has occured

TEIF[4]

Bit 15: Channel 4 Transfer Error flag.

Allowed values:
0: NoError: No transfer error
1: Error: A transfer error has occured

GIF[5]

Bit 16: Channel 5 Global interrupt flag.

Allowed values:
0: NoEvent: No transfer error, half event, complete event
1: Event: A transfer error, half event or complete event has occured

TCIF[5]

Bit 17: Channel 5 Transfer Complete flag.

Allowed values:
0: NotComplete: No transfer complete event
1: Complete: A transfer complete event has occured

HTIF[5]

Bit 18: Channel 5 Half Transfer Complete flag.

Allowed values:
0: NotHalf: No half transfer event
1: Half: A half transfer event has occured

TEIF[5]

Bit 19: Channel 5 Transfer Error flag.

Allowed values:
0: NoError: No transfer error
1: Error: A transfer error has occured

GIF[6]

Bit 20: Channel 6 Global interrupt flag.

Allowed values:
0: NoEvent: No transfer error, half event, complete event
1: Event: A transfer error, half event or complete event has occured

TCIF[6]

Bit 21: Channel 6 Transfer Complete flag.

Allowed values:
0: NotComplete: No transfer complete event
1: Complete: A transfer complete event has occured

HTIF[6]

Bit 22: Channel 6 Half Transfer Complete flag.

Allowed values:
0: NotHalf: No half transfer event
1: Half: A half transfer event has occured

TEIF[6]

Bit 23: Channel 6 Transfer Error flag.

Allowed values:
0: NoError: No transfer error
1: Error: A transfer error has occured

GIF[7]

Bit 24: Channel 7 Global interrupt flag.

Allowed values:
0: NoEvent: No transfer error, half event, complete event
1: Event: A transfer error, half event or complete event has occured

TCIF[7]

Bit 25: Channel 7 Transfer Complete flag.

Allowed values:
0: NotComplete: No transfer complete event
1: Complete: A transfer complete event has occured

HTIF[7]

Bit 26: Channel 7 Half Transfer Complete flag.

Allowed values:
0: NotHalf: No half transfer event
1: Half: A half transfer event has occured

TEIF[7]

Bit 27: Channel 7 Transfer Error flag.

Allowed values:
0: NoError: No transfer error
1: Error: A transfer error has occured

IFCR

DMA interrupt flag clear register (DMA_IFCR)

Offset: 0x4, size: 32, reset: 0x00000000, access: write-only

28/28 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				CTEIF[7] w	CHTIF[7] w	CTCIF[7] w	CGIF[7] w	CTEIF[6] w	CHTIF[6] w	CTCIF[6] w	CGIF[6] w	CTEIF[5] w	CHTIF[5] w	CTCIF[5] w	CGIF[5] w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CTEIF[4] w	CHTIF[4] w	CTCIF[4] w	CGIF[4] w	CTEIF[3] w	CHTIF[3] w	CTCIF[3] w	CGIF[3] w	CTEIF[2] w	CHTIF[2] w	CTCIF[2] w	CGIF[2] w	CTEIF[1] w	CHTIF[1] w	CTCIF[1] w	CGIF[1] w

Toggle fields

CGIF[1]

Bit 0: Channel 1 Global interrupt clear.

Allowed values:
1: Clear: Clears the GIF, TEIF, HTIF, TCIF flags in the ISR register

CTCIF[1]

Bit 1: Channel 1 Transfer Complete clear.

Allowed values:
1: Clear: Clears the TCIF flag in the ISR register

CHTIF[1]

Bit 2: Channel 1 Half Transfer clear.

Allowed values:
1: Clear: Clears the HTIF flag in the ISR register

CTEIF[1]

Bit 3: Channel 1 Transfer Error clear.

Allowed values:
1: Clear: Clears the TEIF flag in the ISR register

CGIF[2]

Bit 4: Channel 2 Global interrupt clear.

Allowed values:
1: Clear: Clears the GIF, TEIF, HTIF, TCIF flags in the ISR register

CTCIF[2]

Bit 5: Channel 2 Transfer Complete clear.

Allowed values:
1: Clear: Clears the TCIF flag in the ISR register

CHTIF[2]

Bit 6: Channel 2 Half Transfer clear.

Allowed values:
1: Clear: Clears the HTIF flag in the ISR register

CTEIF[2]

Bit 7: Channel 2 Transfer Error clear.

Allowed values:
1: Clear: Clears the TEIF flag in the ISR register

CGIF[3]

Bit 8: Channel 3 Global interrupt clear.

Allowed values:
1: Clear: Clears the GIF, TEIF, HTIF, TCIF flags in the ISR register

CTCIF[3]

Bit 9: Channel 3 Transfer Complete clear.

Allowed values:
1: Clear: Clears the TCIF flag in the ISR register

CHTIF[3]

Bit 10: Channel 3 Half Transfer clear.

Allowed values:
1: Clear: Clears the HTIF flag in the ISR register

CTEIF[3]

Bit 11: Channel 3 Transfer Error clear.

Allowed values:
1: Clear: Clears the TEIF flag in the ISR register

CGIF[4]

Bit 12: Channel 4 Global interrupt clear.

Allowed values:
1: Clear: Clears the GIF, TEIF, HTIF, TCIF flags in the ISR register

CTCIF[4]

Bit 13: Channel 4 Transfer Complete clear.

Allowed values:
1: Clear: Clears the TCIF flag in the ISR register

CHTIF[4]

Bit 14: Channel 4 Half Transfer clear.

Allowed values:
1: Clear: Clears the HTIF flag in the ISR register

CTEIF[4]

Bit 15: Channel 4 Transfer Error clear.

Allowed values:
1: Clear: Clears the TEIF flag in the ISR register

CGIF[5]

Bit 16: Channel 5 Global interrupt clear.

Allowed values:
1: Clear: Clears the GIF, TEIF, HTIF, TCIF flags in the ISR register

CTCIF[5]

Bit 17: Channel 5 Transfer Complete clear.

Allowed values:
1: Clear: Clears the TCIF flag in the ISR register

CHTIF[5]

Bit 18: Channel 5 Half Transfer clear.

Allowed values:
1: Clear: Clears the HTIF flag in the ISR register

CTEIF[5]

Bit 19: Channel 5 Transfer Error clear.

Allowed values:
1: Clear: Clears the TEIF flag in the ISR register

CGIF[6]

Bit 20: Channel 6 Global interrupt clear.

Allowed values:
1: Clear: Clears the GIF, TEIF, HTIF, TCIF flags in the ISR register

CTCIF[6]

Bit 21: Channel 6 Transfer Complete clear.

Allowed values:
1: Clear: Clears the TCIF flag in the ISR register

CHTIF[6]

Bit 22: Channel 6 Half Transfer clear.

Allowed values:
1: Clear: Clears the HTIF flag in the ISR register

CTEIF[6]

Bit 23: Channel 6 Transfer Error clear.

Allowed values:
1: Clear: Clears the TEIF flag in the ISR register

CGIF[7]

Bit 24: Channel 7 Global interrupt clear.

Allowed values:
1: Clear: Clears the GIF, TEIF, HTIF, TCIF flags in the ISR register

CTCIF[7]

Bit 25: Channel 7 Transfer Complete clear.

Allowed values:
1: Clear: Clears the TCIF flag in the ISR register

CHTIF[7]

Bit 26: Channel 7 Half Transfer clear.

Allowed values:
1: Clear: Clears the HTIF flag in the ISR register

CTEIF[7]

Bit 27: Channel 7 Transfer Error clear.

Allowed values:
1: Clear: Clears the TEIF flag in the ISR register

CR [1]

DMA channel configuration register (DMA_CCR)

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

12/12 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	MEM2MEM rw	PL rw		MSIZE rw		PSIZE rw		MINC rw	PINC rw	CIRC rw	DIR rw	TEIE rw	HTIE rw	TCIE rw	EN rw

Toggle fields

EN

Bit 0: Channel enable.

Allowed values:
0: Disabled: Channel disabled
1: Enabled: Channel enabled

TCIE

Bit 1: Transfer complete interrupt enable.

Allowed values:
0: Disabled: Transfer Complete interrupt disabled
1: Enabled: Transfer Complete interrupt enabled

HTIE

Bit 2: Half Transfer interrupt enable.

Allowed values:
0: Disabled: Half Transfer interrupt disabled
1: Enabled: Half Transfer interrupt enabled

TEIE

Bit 3: Transfer error interrupt enable.

Allowed values:
0: Disabled: Transfer Error interrupt disabled
1: Enabled: Transfer Error interrupt enabled

DIR

Bit 4: Data transfer direction.

Allowed values:
0: FromPeripheral: Read from peripheral
1: FromMemory: Read from memory

CIRC

Bit 5: Circular mode.

Allowed values:
0: Disabled: Circular buffer disabled
1: Enabled: Circular buffer enabled

PINC

Bit 6: Peripheral increment mode.

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

MINC

Bit 7: Memory increment mode.

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

PSIZE

Bits 8-9: Peripheral size.

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

MSIZE

Bits 10-11: Memory size.

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

PL

Bits 12-13: Channel Priority level.

Allowed values:
0: Low: Low priority
1: Medium: Medium priority
2: High: High priority
3: VeryHigh: Very high priority

MEM2MEM

Bit 14: Memory to memory mode.

Allowed values:
0: Disabled: Memory to memory mode disabled
1: Enabled: Memory to memory mode enabled

NDTR [1]

DMA channel 1 number of data register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
NDT rw

Toggle fields

NDT

Bits 0-15: Number of data to transfer.

Allowed values: 0x0-0xffff

PAR [1]

DMA channel 1 peripheral address register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PA rw

Toggle fields

PA

Bits 0-31: Peripheral address.

MAR [1]

DMA channel 1 memory address register

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MA rw

Toggle fields

MA

Bits 0-31: Memory address.

CR [2]

DMA channel configuration register (DMA_CCR)

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

12/12 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	MEM2MEM rw	PL rw		MSIZE rw		PSIZE rw		MINC rw	PINC rw	CIRC rw	DIR rw	TEIE rw	HTIE rw	TCIE rw	EN rw

Toggle fields

EN

Bit 0: Channel enable.

Allowed values:
0: Disabled: Channel disabled
1: Enabled: Channel enabled

TCIE

Bit 1: Transfer complete interrupt enable.

Allowed values:
0: Disabled: Transfer Complete interrupt disabled
1: Enabled: Transfer Complete interrupt enabled

HTIE

Bit 2: Half Transfer interrupt enable.

Allowed values:
0: Disabled: Half Transfer interrupt disabled
1: Enabled: Half Transfer interrupt enabled

TEIE

Bit 3: Transfer error interrupt enable.

Allowed values:
0: Disabled: Transfer Error interrupt disabled
1: Enabled: Transfer Error interrupt enabled

DIR

Bit 4: Data transfer direction.

Allowed values:
0: FromPeripheral: Read from peripheral
1: FromMemory: Read from memory

CIRC

Bit 5: Circular mode.

Allowed values:
0: Disabled: Circular buffer disabled
1: Enabled: Circular buffer enabled

PINC

Bit 6: Peripheral increment mode.

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

MINC

Bit 7: Memory increment mode.

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

PSIZE

Bits 8-9: Peripheral size.

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

MSIZE

Bits 10-11: Memory size.

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

PL

Bits 12-13: Channel Priority level.

Allowed values:
0: Low: Low priority
1: Medium: Medium priority
2: High: High priority
3: VeryHigh: Very high priority

MEM2MEM

Bit 14: Memory to memory mode.

Allowed values:
0: Disabled: Memory to memory mode disabled
1: Enabled: Memory to memory mode enabled

NDTR [2]

DMA channel 1 number of data register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
NDT rw

Toggle fields

NDT

Bits 0-15: Number of data to transfer.

Allowed values: 0x0-0xffff

PAR [2]

DMA channel 1 peripheral address register

Offset: 0x24, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PA rw

Toggle fields

PA

Bits 0-31: Peripheral address.

MAR [2]

DMA channel 1 memory address register

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MA rw

Toggle fields

MA

Bits 0-31: Memory address.

CR [3]

DMA channel configuration register (DMA_CCR)

Offset: 0x30, size: 32, reset: 0x00000000, access: read-write

12/12 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	MEM2MEM rw	PL rw		MSIZE rw		PSIZE rw		MINC rw	PINC rw	CIRC rw	DIR rw	TEIE rw	HTIE rw	TCIE rw	EN rw

Toggle fields

EN

Bit 0: Channel enable.

Allowed values:
0: Disabled: Channel disabled
1: Enabled: Channel enabled

TCIE

Bit 1: Transfer complete interrupt enable.

Allowed values:
0: Disabled: Transfer Complete interrupt disabled
1: Enabled: Transfer Complete interrupt enabled

HTIE

Bit 2: Half Transfer interrupt enable.

Allowed values:
0: Disabled: Half Transfer interrupt disabled
1: Enabled: Half Transfer interrupt enabled

TEIE

Bit 3: Transfer error interrupt enable.

Allowed values:
0: Disabled: Transfer Error interrupt disabled
1: Enabled: Transfer Error interrupt enabled

DIR

Bit 4: Data transfer direction.

Allowed values:
0: FromPeripheral: Read from peripheral
1: FromMemory: Read from memory

CIRC

Bit 5: Circular mode.

Allowed values:
0: Disabled: Circular buffer disabled
1: Enabled: Circular buffer enabled

PINC

Bit 6: Peripheral increment mode.

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

MINC

Bit 7: Memory increment mode.

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

PSIZE

Bits 8-9: Peripheral size.

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

MSIZE

Bits 10-11: Memory size.

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

PL

Bits 12-13: Channel Priority level.

Allowed values:
0: Low: Low priority
1: Medium: Medium priority
2: High: High priority
3: VeryHigh: Very high priority

MEM2MEM

Bit 14: Memory to memory mode.

Allowed values:
0: Disabled: Memory to memory mode disabled
1: Enabled: Memory to memory mode enabled

NDTR [3]

DMA channel 1 number of data register

Offset: 0x34, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
NDT rw

Toggle fields

NDT

Bits 0-15: Number of data to transfer.

Allowed values: 0x0-0xffff

PAR [3]

DMA channel 1 peripheral address register

Offset: 0x38, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PA rw

Toggle fields

PA

Bits 0-31: Peripheral address.

MAR [3]

DMA channel 1 memory address register

Offset: 0x3c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MA rw

Toggle fields

MA

Bits 0-31: Memory address.

CR [4]

DMA channel configuration register (DMA_CCR)

Offset: 0x44, size: 32, reset: 0x00000000, access: read-write

12/12 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	MEM2MEM rw	PL rw		MSIZE rw		PSIZE rw		MINC rw	PINC rw	CIRC rw	DIR rw	TEIE rw	HTIE rw	TCIE rw	EN rw

Toggle fields

EN

Bit 0: Channel enable.

Allowed values:
0: Disabled: Channel disabled
1: Enabled: Channel enabled

TCIE

Bit 1: Transfer complete interrupt enable.

Allowed values:
0: Disabled: Transfer Complete interrupt disabled
1: Enabled: Transfer Complete interrupt enabled

HTIE

Bit 2: Half Transfer interrupt enable.

Allowed values:
0: Disabled: Half Transfer interrupt disabled
1: Enabled: Half Transfer interrupt enabled

TEIE

Bit 3: Transfer error interrupt enable.

Allowed values:
0: Disabled: Transfer Error interrupt disabled
1: Enabled: Transfer Error interrupt enabled

DIR

Bit 4: Data transfer direction.

Allowed values:
0: FromPeripheral: Read from peripheral
1: FromMemory: Read from memory

CIRC

Bit 5: Circular mode.

Allowed values:
0: Disabled: Circular buffer disabled
1: Enabled: Circular buffer enabled

PINC

Bit 6: Peripheral increment mode.

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

MINC

Bit 7: Memory increment mode.

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

PSIZE

Bits 8-9: Peripheral size.

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

MSIZE

Bits 10-11: Memory size.

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

PL

Bits 12-13: Channel Priority level.

Allowed values:
0: Low: Low priority
1: Medium: Medium priority
2: High: High priority
3: VeryHigh: Very high priority

MEM2MEM

Bit 14: Memory to memory mode.

Allowed values:
0: Disabled: Memory to memory mode disabled
1: Enabled: Memory to memory mode enabled

NDTR [4]

DMA channel 1 number of data register

Offset: 0x48, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
NDT rw

Toggle fields

NDT

Bits 0-15: Number of data to transfer.

Allowed values: 0x0-0xffff

PAR [4]

DMA channel 1 peripheral address register

Offset: 0x4c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PA rw

Toggle fields

PA

Bits 0-31: Peripheral address.

MAR [4]

DMA channel 1 memory address register

Offset: 0x50, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MA rw

Toggle fields

MA

Bits 0-31: Memory address.

CR [5]

DMA channel configuration register (DMA_CCR)

Offset: 0x58, size: 32, reset: 0x00000000, access: read-write

12/12 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	MEM2MEM rw	PL rw		MSIZE rw		PSIZE rw		MINC rw	PINC rw	CIRC rw	DIR rw	TEIE rw	HTIE rw	TCIE rw	EN rw

Toggle fields

EN

Bit 0: Channel enable.

Allowed values:
0: Disabled: Channel disabled
1: Enabled: Channel enabled

TCIE

Bit 1: Transfer complete interrupt enable.

Allowed values:
0: Disabled: Transfer Complete interrupt disabled
1: Enabled: Transfer Complete interrupt enabled

HTIE

Bit 2: Half Transfer interrupt enable.

Allowed values:
0: Disabled: Half Transfer interrupt disabled
1: Enabled: Half Transfer interrupt enabled

TEIE

Bit 3: Transfer error interrupt enable.

Allowed values:
0: Disabled: Transfer Error interrupt disabled
1: Enabled: Transfer Error interrupt enabled

DIR

Bit 4: Data transfer direction.

Allowed values:
0: FromPeripheral: Read from peripheral
1: FromMemory: Read from memory

CIRC

Bit 5: Circular mode.

Allowed values:
0: Disabled: Circular buffer disabled
1: Enabled: Circular buffer enabled

PINC

Bit 6: Peripheral increment mode.

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

MINC

Bit 7: Memory increment mode.

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

PSIZE

Bits 8-9: Peripheral size.

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

MSIZE

Bits 10-11: Memory size.

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

PL

Bits 12-13: Channel Priority level.

Allowed values:
0: Low: Low priority
1: Medium: Medium priority
2: High: High priority
3: VeryHigh: Very high priority

MEM2MEM

Bit 14: Memory to memory mode.

Allowed values:
0: Disabled: Memory to memory mode disabled
1: Enabled: Memory to memory mode enabled

NDTR [5]

DMA channel 1 number of data register

Offset: 0x5c, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
NDT rw

Toggle fields

NDT

Bits 0-15: Number of data to transfer.

Allowed values: 0x0-0xffff

PAR [5]

DMA channel 1 peripheral address register

Offset: 0x60, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PA rw

Toggle fields

PA

Bits 0-31: Peripheral address.

MAR [5]

DMA channel 1 memory address register

Offset: 0x64, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MA rw

Toggle fields

MA

Bits 0-31: Memory address.

CR [6]

DMA channel configuration register (DMA_CCR)

Offset: 0x6c, size: 32, reset: 0x00000000, access: read-write

12/12 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	MEM2MEM rw	PL rw		MSIZE rw		PSIZE rw		MINC rw	PINC rw	CIRC rw	DIR rw	TEIE rw	HTIE rw	TCIE rw	EN rw

Toggle fields

EN

Bit 0: Channel enable.

Allowed values:
0: Disabled: Channel disabled
1: Enabled: Channel enabled

TCIE

Bit 1: Transfer complete interrupt enable.

Allowed values:
0: Disabled: Transfer Complete interrupt disabled
1: Enabled: Transfer Complete interrupt enabled

HTIE

Bit 2: Half Transfer interrupt enable.

Allowed values:
0: Disabled: Half Transfer interrupt disabled
1: Enabled: Half Transfer interrupt enabled

TEIE

Bit 3: Transfer error interrupt enable.

Allowed values:
0: Disabled: Transfer Error interrupt disabled
1: Enabled: Transfer Error interrupt enabled

DIR

Bit 4: Data transfer direction.

Allowed values:
0: FromPeripheral: Read from peripheral
1: FromMemory: Read from memory

CIRC

Bit 5: Circular mode.

Allowed values:
0: Disabled: Circular buffer disabled
1: Enabled: Circular buffer enabled

PINC

Bit 6: Peripheral increment mode.

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

MINC

Bit 7: Memory increment mode.

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

PSIZE

Bits 8-9: Peripheral size.

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

MSIZE

Bits 10-11: Memory size.

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

PL

Bits 12-13: Channel Priority level.

Allowed values:
0: Low: Low priority
1: Medium: Medium priority
2: High: High priority
3: VeryHigh: Very high priority

MEM2MEM

Bit 14: Memory to memory mode.

Allowed values:
0: Disabled: Memory to memory mode disabled
1: Enabled: Memory to memory mode enabled

NDTR [6]

DMA channel 1 number of data register

Offset: 0x70, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
NDT rw

Toggle fields

NDT

Bits 0-15: Number of data to transfer.

Allowed values: 0x0-0xffff

PAR [6]

DMA channel 1 peripheral address register

Offset: 0x74, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PA rw

Toggle fields

PA

Bits 0-31: Peripheral address.

MAR [6]

DMA channel 1 memory address register

Offset: 0x78, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MA rw

Toggle fields

MA

Bits 0-31: Memory address.

CR [7]

DMA channel configuration register (DMA_CCR)

Offset: 0x80, size: 32, reset: 0x00000000, access: read-write

12/12 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	MEM2MEM rw	PL rw		MSIZE rw		PSIZE rw		MINC rw	PINC rw	CIRC rw	DIR rw	TEIE rw	HTIE rw	TCIE rw	EN rw

Toggle fields

EN

Bit 0: Channel enable.

Allowed values:
0: Disabled: Channel disabled
1: Enabled: Channel enabled

TCIE

Bit 1: Transfer complete interrupt enable.

Allowed values:
0: Disabled: Transfer Complete interrupt disabled
1: Enabled: Transfer Complete interrupt enabled

HTIE

Bit 2: Half Transfer interrupt enable.

Allowed values:
0: Disabled: Half Transfer interrupt disabled
1: Enabled: Half Transfer interrupt enabled

TEIE

Bit 3: Transfer error interrupt enable.

Allowed values:
0: Disabled: Transfer Error interrupt disabled
1: Enabled: Transfer Error interrupt enabled

DIR

Bit 4: Data transfer direction.

Allowed values:
0: FromPeripheral: Read from peripheral
1: FromMemory: Read from memory

CIRC

Bit 5: Circular mode.

Allowed values:
0: Disabled: Circular buffer disabled
1: Enabled: Circular buffer enabled

PINC

Bit 6: Peripheral increment mode.

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

MINC

Bit 7: Memory increment mode.

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

PSIZE

Bits 8-9: Peripheral size.

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

MSIZE

Bits 10-11: Memory size.

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

PL

Bits 12-13: Channel Priority level.

Allowed values:
0: Low: Low priority
1: Medium: Medium priority
2: High: High priority
3: VeryHigh: Very high priority

MEM2MEM

Bit 14: Memory to memory mode.

Allowed values:
0: Disabled: Memory to memory mode disabled
1: Enabled: Memory to memory mode enabled

NDTR [7]

DMA channel 1 number of data register

Offset: 0x84, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
NDT rw

Toggle fields

NDT

Bits 0-15: Number of data to transfer.

Allowed values: 0x0-0xffff

PAR [7]

DMA channel 1 peripheral address register

Offset: 0x88, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PA rw

Toggle fields

PA

Bits 0-31: Peripheral address.

MAR [7]

DMA channel 1 memory address register

Offset: 0x8c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MA rw

Toggle fields

MA

Bits 0-31: Memory address.

DMA2

0x40020400: DMA controller 1

147/161 fields covered.

Toggle register map

Offset	Name	31	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	ISR		TEIF[7]	HTIF[7]	TCIF[7]	GIF[7]	TEIF[6]	HTIF[6]	TCIF[6]	GIF[6]	TEIF[5]	HTIF[5]	TCIF[5]	GIF[5]	TEIF[4]	HTIF[4]	TCIF[4]	GIF[4]	TEIF[3]	HTIF[3]	TCIF[3]	GIF[3]	TEIF[2]	HTIF[2]	TCIF[2]	GIF[2]	TEIF[1]	HTIF[1]	TCIF[1]	GIF[1]
0x4	IFCR		CTEIF[7]	CHTIF[7]	CTCIF[7]	CGIF[7]	CTEIF[6]	CHTIF[6]	CTCIF[6]	CGIF[6]	CTEIF[5]	CHTIF[5]	CTCIF[5]	CGIF[5]	CTEIF[4]	CHTIF[4]	CTCIF[4]	CGIF[4]	CTEIF[3]	CHTIF[3]	CTCIF[3]	CGIF[3]	CTEIF[2]	CHTIF[2]	CTCIF[2]	CGIF[2]	CTEIF[1]	CHTIF[1]	CTCIF[1]	CGIF[1]
0x8	CR [1]															MEM2MEM	PL		MSIZE		PSIZE		MINC	PINC	CIRC	DIR	TEIE	HTIE	TCIE	EN
0xc	NDTR [1]														NDT
0x10	PAR [1]	PA													PA
0x14	MAR [1]	MA													MA
0x1c	CR [2]															MEM2MEM	PL		MSIZE		PSIZE		MINC	PINC	CIRC	DIR	TEIE	HTIE	TCIE	EN
0x20	NDTR [2]														NDT
0x24	PAR [2]	PA													PA
0x28	MAR [2]	MA													MA
0x30	CR [3]															MEM2MEM	PL		MSIZE		PSIZE		MINC	PINC	CIRC	DIR	TEIE	HTIE	TCIE	EN
0x34	NDTR [3]														NDT
0x38	PAR [3]	PA													PA
0x3c	MAR [3]	MA													MA
0x44	CR [4]															MEM2MEM	PL		MSIZE		PSIZE		MINC	PINC	CIRC	DIR	TEIE	HTIE	TCIE	EN
0x48	NDTR [4]														NDT
0x4c	PAR [4]	PA													PA
0x50	MAR [4]	MA													MA
0x58	CR [5]															MEM2MEM	PL		MSIZE		PSIZE		MINC	PINC	CIRC	DIR	TEIE	HTIE	TCIE	EN
0x5c	NDTR [5]														NDT
0x60	PAR [5]	PA													PA
0x64	MAR [5]	MA													MA
0x6c	CR [6]															MEM2MEM	PL		MSIZE		PSIZE		MINC	PINC	CIRC	DIR	TEIE	HTIE	TCIE	EN
0x70	NDTR [6]														NDT
0x74	PAR [6]	PA													PA
0x78	MAR [6]	MA													MA
0x80	CR [7]															MEM2MEM	PL		MSIZE		PSIZE		MINC	PINC	CIRC	DIR	TEIE	HTIE	TCIE	EN
0x84	NDTR [7]														NDT
0x88	PAR [7]	PA													PA
0x8c	MAR [7]	MA													MA

Toggle registers

ISR

DMA interrupt status register (DMA_ISR)

Offset: 0x0, size: 32, reset: 0x00000000, access: read-only

28/28 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				TEIF[7] r	HTIF[7] r	TCIF[7] r	GIF[7] r	TEIF[6] r	HTIF[6] r	TCIF[6] r	GIF[6] r	TEIF[5] r	HTIF[5] r	TCIF[5] r	GIF[5] r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TEIF[4] r	HTIF[4] r	TCIF[4] r	GIF[4] r	TEIF[3] r	HTIF[3] r	TCIF[3] r	GIF[3] r	TEIF[2] r	HTIF[2] r	TCIF[2] r	GIF[2] r	TEIF[1] r	HTIF[1] r	TCIF[1] r	GIF[1] r

Toggle fields

GIF[1]

Bit 0: Channel 1 Global interrupt flag.

Allowed values:
0: NoEvent: No transfer error, half event, complete event
1: Event: A transfer error, half event or complete event has occured

TCIF[1]

Bit 1: Channel 1 Transfer Complete flag.

Allowed values:
0: NotComplete: No transfer complete event
1: Complete: A transfer complete event has occured

HTIF[1]

Bit 2: Channel 1 Half Transfer Complete flag.

Allowed values:
0: NotHalf: No half transfer event
1: Half: A half transfer event has occured

TEIF[1]

Bit 3: Channel 1 Transfer Error flag.

Allowed values:
0: NoError: No transfer error
1: Error: A transfer error has occured

GIF[2]

Bit 4: Channel 2 Global interrupt flag.

Allowed values:
0: NoEvent: No transfer error, half event, complete event
1: Event: A transfer error, half event or complete event has occured

TCIF[2]

Bit 5: Channel 2 Transfer Complete flag.

Allowed values:
0: NotComplete: No transfer complete event
1: Complete: A transfer complete event has occured

HTIF[2]

Bit 6: Channel 2 Half Transfer Complete flag.

Allowed values:
0: NotHalf: No half transfer event
1: Half: A half transfer event has occured

TEIF[2]

Bit 7: Channel 2 Transfer Error flag.

Allowed values:
0: NoError: No transfer error
1: Error: A transfer error has occured

GIF[3]

Bit 8: Channel 3 Global interrupt flag.

Allowed values:
0: NoEvent: No transfer error, half event, complete event
1: Event: A transfer error, half event or complete event has occured

TCIF[3]

Bit 9: Channel 3 Transfer Complete flag.

Allowed values:
0: NotComplete: No transfer complete event
1: Complete: A transfer complete event has occured

HTIF[3]

Bit 10: Channel 3 Half Transfer Complete flag.

Allowed values:
0: NotHalf: No half transfer event
1: Half: A half transfer event has occured

TEIF[3]

Bit 11: Channel 3 Transfer Error flag.

Allowed values:
0: NoError: No transfer error
1: Error: A transfer error has occured

GIF[4]

Bit 12: Channel 4 Global interrupt flag.

Allowed values:
0: NoEvent: No transfer error, half event, complete event
1: Event: A transfer error, half event or complete event has occured

TCIF[4]

Bit 13: Channel 4 Transfer Complete flag.

Allowed values:
0: NotComplete: No transfer complete event
1: Complete: A transfer complete event has occured

HTIF[4]

Bit 14: Channel 4 Half Transfer Complete flag.

Allowed values:
0: NotHalf: No half transfer event
1: Half: A half transfer event has occured

TEIF[4]

Bit 15: Channel 4 Transfer Error flag.

Allowed values:
0: NoError: No transfer error
1: Error: A transfer error has occured

GIF[5]

Bit 16: Channel 5 Global interrupt flag.

Allowed values:
0: NoEvent: No transfer error, half event, complete event
1: Event: A transfer error, half event or complete event has occured

TCIF[5]

Bit 17: Channel 5 Transfer Complete flag.

Allowed values:
0: NotComplete: No transfer complete event
1: Complete: A transfer complete event has occured

HTIF[5]

Bit 18: Channel 5 Half Transfer Complete flag.

Allowed values:
0: NotHalf: No half transfer event
1: Half: A half transfer event has occured

TEIF[5]

Bit 19: Channel 5 Transfer Error flag.

Allowed values:
0: NoError: No transfer error
1: Error: A transfer error has occured

GIF[6]

Bit 20: Channel 6 Global interrupt flag.

Allowed values:
0: NoEvent: No transfer error, half event, complete event
1: Event: A transfer error, half event or complete event has occured

TCIF[6]

Bit 21: Channel 6 Transfer Complete flag.

Allowed values:
0: NotComplete: No transfer complete event
1: Complete: A transfer complete event has occured

HTIF[6]

Bit 22: Channel 6 Half Transfer Complete flag.

Allowed values:
0: NotHalf: No half transfer event
1: Half: A half transfer event has occured

TEIF[6]

Bit 23: Channel 6 Transfer Error flag.

Allowed values:
0: NoError: No transfer error
1: Error: A transfer error has occured

GIF[7]

Bit 24: Channel 7 Global interrupt flag.

Allowed values:
0: NoEvent: No transfer error, half event, complete event
1: Event: A transfer error, half event or complete event has occured

TCIF[7]

Bit 25: Channel 7 Transfer Complete flag.

Allowed values:
0: NotComplete: No transfer complete event
1: Complete: A transfer complete event has occured

HTIF[7]

Bit 26: Channel 7 Half Transfer Complete flag.

Allowed values:
0: NotHalf: No half transfer event
1: Half: A half transfer event has occured

TEIF[7]

Bit 27: Channel 7 Transfer Error flag.

Allowed values:
0: NoError: No transfer error
1: Error: A transfer error has occured

IFCR

DMA interrupt flag clear register (DMA_IFCR)

Offset: 0x4, size: 32, reset: 0x00000000, access: write-only

28/28 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				CTEIF[7] w	CHTIF[7] w	CTCIF[7] w	CGIF[7] w	CTEIF[6] w	CHTIF[6] w	CTCIF[6] w	CGIF[6] w	CTEIF[5] w	CHTIF[5] w	CTCIF[5] w	CGIF[5] w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CTEIF[4] w	CHTIF[4] w	CTCIF[4] w	CGIF[4] w	CTEIF[3] w	CHTIF[3] w	CTCIF[3] w	CGIF[3] w	CTEIF[2] w	CHTIF[2] w	CTCIF[2] w	CGIF[2] w	CTEIF[1] w	CHTIF[1] w	CTCIF[1] w	CGIF[1] w

Toggle fields

CGIF[1]

Bit 0: Channel 1 Global interrupt clear.

Allowed values:
1: Clear: Clears the GIF, TEIF, HTIF, TCIF flags in the ISR register

CTCIF[1]

Bit 1: Channel 1 Transfer Complete clear.

Allowed values:
1: Clear: Clears the TCIF flag in the ISR register

CHTIF[1]

Bit 2: Channel 1 Half Transfer clear.

Allowed values:
1: Clear: Clears the HTIF flag in the ISR register

CTEIF[1]

Bit 3: Channel 1 Transfer Error clear.

Allowed values:
1: Clear: Clears the TEIF flag in the ISR register

CGIF[2]

Bit 4: Channel 2 Global interrupt clear.

Allowed values:
1: Clear: Clears the GIF, TEIF, HTIF, TCIF flags in the ISR register

CTCIF[2]

Bit 5: Channel 2 Transfer Complete clear.

Allowed values:
1: Clear: Clears the TCIF flag in the ISR register

CHTIF[2]

Bit 6: Channel 2 Half Transfer clear.

Allowed values:
1: Clear: Clears the HTIF flag in the ISR register

CTEIF[2]

Bit 7: Channel 2 Transfer Error clear.

Allowed values:
1: Clear: Clears the TEIF flag in the ISR register

CGIF[3]

Bit 8: Channel 3 Global interrupt clear.

Allowed values:
1: Clear: Clears the GIF, TEIF, HTIF, TCIF flags in the ISR register

CTCIF[3]

Bit 9: Channel 3 Transfer Complete clear.

Allowed values:
1: Clear: Clears the TCIF flag in the ISR register

CHTIF[3]

Bit 10: Channel 3 Half Transfer clear.

Allowed values:
1: Clear: Clears the HTIF flag in the ISR register

CTEIF[3]

Bit 11: Channel 3 Transfer Error clear.

Allowed values:
1: Clear: Clears the TEIF flag in the ISR register

CGIF[4]

Bit 12: Channel 4 Global interrupt clear.

Allowed values:
1: Clear: Clears the GIF, TEIF, HTIF, TCIF flags in the ISR register

CTCIF[4]

Bit 13: Channel 4 Transfer Complete clear.

Allowed values:
1: Clear: Clears the TCIF flag in the ISR register

CHTIF[4]

Bit 14: Channel 4 Half Transfer clear.

Allowed values:
1: Clear: Clears the HTIF flag in the ISR register

CTEIF[4]

Bit 15: Channel 4 Transfer Error clear.

Allowed values:
1: Clear: Clears the TEIF flag in the ISR register

CGIF[5]

Bit 16: Channel 5 Global interrupt clear.

Allowed values:
1: Clear: Clears the GIF, TEIF, HTIF, TCIF flags in the ISR register

CTCIF[5]

Bit 17: Channel 5 Transfer Complete clear.

Allowed values:
1: Clear: Clears the TCIF flag in the ISR register

CHTIF[5]

Bit 18: Channel 5 Half Transfer clear.

Allowed values:
1: Clear: Clears the HTIF flag in the ISR register

CTEIF[5]

Bit 19: Channel 5 Transfer Error clear.

Allowed values:
1: Clear: Clears the TEIF flag in the ISR register

CGIF[6]

Bit 20: Channel 6 Global interrupt clear.

Allowed values:
1: Clear: Clears the GIF, TEIF, HTIF, TCIF flags in the ISR register

CTCIF[6]

Bit 21: Channel 6 Transfer Complete clear.

Allowed values:
1: Clear: Clears the TCIF flag in the ISR register

CHTIF[6]

Bit 22: Channel 6 Half Transfer clear.

Allowed values:
1: Clear: Clears the HTIF flag in the ISR register

CTEIF[6]

Bit 23: Channel 6 Transfer Error clear.

Allowed values:
1: Clear: Clears the TEIF flag in the ISR register

CGIF[7]

Bit 24: Channel 7 Global interrupt clear.

Allowed values:
1: Clear: Clears the GIF, TEIF, HTIF, TCIF flags in the ISR register

CTCIF[7]

Bit 25: Channel 7 Transfer Complete clear.

Allowed values:
1: Clear: Clears the TCIF flag in the ISR register

CHTIF[7]

Bit 26: Channel 7 Half Transfer clear.

Allowed values:
1: Clear: Clears the HTIF flag in the ISR register

CTEIF[7]

Bit 27: Channel 7 Transfer Error clear.

Allowed values:
1: Clear: Clears the TEIF flag in the ISR register

CR [1]

DMA channel configuration register (DMA_CCR)

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

12/12 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	MEM2MEM rw	PL rw		MSIZE rw		PSIZE rw		MINC rw	PINC rw	CIRC rw	DIR rw	TEIE rw	HTIE rw	TCIE rw	EN rw

Toggle fields

EN

Bit 0: Channel enable.

Allowed values:
0: Disabled: Channel disabled
1: Enabled: Channel enabled

TCIE

Bit 1: Transfer complete interrupt enable.

Allowed values:
0: Disabled: Transfer Complete interrupt disabled
1: Enabled: Transfer Complete interrupt enabled

HTIE

Bit 2: Half Transfer interrupt enable.

Allowed values:
0: Disabled: Half Transfer interrupt disabled
1: Enabled: Half Transfer interrupt enabled

TEIE

Bit 3: Transfer error interrupt enable.

Allowed values:
0: Disabled: Transfer Error interrupt disabled
1: Enabled: Transfer Error interrupt enabled

DIR

Bit 4: Data transfer direction.

Allowed values:
0: FromPeripheral: Read from peripheral
1: FromMemory: Read from memory

CIRC

Bit 5: Circular mode.

Allowed values:
0: Disabled: Circular buffer disabled
1: Enabled: Circular buffer enabled

PINC

Bit 6: Peripheral increment mode.

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

MINC

Bit 7: Memory increment mode.

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

PSIZE

Bits 8-9: Peripheral size.

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

MSIZE

Bits 10-11: Memory size.

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

PL

Bits 12-13: Channel Priority level.

Allowed values:
0: Low: Low priority
1: Medium: Medium priority
2: High: High priority
3: VeryHigh: Very high priority

MEM2MEM

Bit 14: Memory to memory mode.

Allowed values:
0: Disabled: Memory to memory mode disabled
1: Enabled: Memory to memory mode enabled

NDTR [1]

DMA channel 1 number of data register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
NDT rw

Toggle fields

NDT

Bits 0-15: Number of data to transfer.

Allowed values: 0x0-0xffff

PAR [1]

DMA channel 1 peripheral address register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PA rw

Toggle fields

PA

Bits 0-31: Peripheral address.

MAR [1]

DMA channel 1 memory address register

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MA rw

Toggle fields

MA

Bits 0-31: Memory address.

CR [2]

DMA channel configuration register (DMA_CCR)

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

12/12 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	MEM2MEM rw	PL rw		MSIZE rw		PSIZE rw		MINC rw	PINC rw	CIRC rw	DIR rw	TEIE rw	HTIE rw	TCIE rw	EN rw

Toggle fields

EN

Bit 0: Channel enable.

Allowed values:
0: Disabled: Channel disabled
1: Enabled: Channel enabled

TCIE

Bit 1: Transfer complete interrupt enable.

Allowed values:
0: Disabled: Transfer Complete interrupt disabled
1: Enabled: Transfer Complete interrupt enabled

HTIE

Bit 2: Half Transfer interrupt enable.

Allowed values:
0: Disabled: Half Transfer interrupt disabled
1: Enabled: Half Transfer interrupt enabled

TEIE

Bit 3: Transfer error interrupt enable.

Allowed values:
0: Disabled: Transfer Error interrupt disabled
1: Enabled: Transfer Error interrupt enabled

DIR

Bit 4: Data transfer direction.

Allowed values:
0: FromPeripheral: Read from peripheral
1: FromMemory: Read from memory

CIRC

Bit 5: Circular mode.

Allowed values:
0: Disabled: Circular buffer disabled
1: Enabled: Circular buffer enabled

PINC

Bit 6: Peripheral increment mode.

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

MINC

Bit 7: Memory increment mode.

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

PSIZE

Bits 8-9: Peripheral size.

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

MSIZE

Bits 10-11: Memory size.

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

PL

Bits 12-13: Channel Priority level.

Allowed values:
0: Low: Low priority
1: Medium: Medium priority
2: High: High priority
3: VeryHigh: Very high priority

MEM2MEM

Bit 14: Memory to memory mode.

Allowed values:
0: Disabled: Memory to memory mode disabled
1: Enabled: Memory to memory mode enabled

NDTR [2]

DMA channel 1 number of data register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
NDT rw

Toggle fields

NDT

Bits 0-15: Number of data to transfer.

Allowed values: 0x0-0xffff

PAR [2]

DMA channel 1 peripheral address register

Offset: 0x24, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PA rw

Toggle fields

PA

Bits 0-31: Peripheral address.

MAR [2]

DMA channel 1 memory address register

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MA rw

Toggle fields

MA

Bits 0-31: Memory address.

CR [3]

DMA channel configuration register (DMA_CCR)

Offset: 0x30, size: 32, reset: 0x00000000, access: read-write

12/12 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	MEM2MEM rw	PL rw		MSIZE rw		PSIZE rw		MINC rw	PINC rw	CIRC rw	DIR rw	TEIE rw	HTIE rw	TCIE rw	EN rw

Toggle fields

EN

Bit 0: Channel enable.

Allowed values:
0: Disabled: Channel disabled
1: Enabled: Channel enabled

TCIE

Bit 1: Transfer complete interrupt enable.

Allowed values:
0: Disabled: Transfer Complete interrupt disabled
1: Enabled: Transfer Complete interrupt enabled

HTIE

Bit 2: Half Transfer interrupt enable.

Allowed values:
0: Disabled: Half Transfer interrupt disabled
1: Enabled: Half Transfer interrupt enabled

TEIE

Bit 3: Transfer error interrupt enable.

Allowed values:
0: Disabled: Transfer Error interrupt disabled
1: Enabled: Transfer Error interrupt enabled

DIR

Bit 4: Data transfer direction.

Allowed values:
0: FromPeripheral: Read from peripheral
1: FromMemory: Read from memory

CIRC

Bit 5: Circular mode.

Allowed values:
0: Disabled: Circular buffer disabled
1: Enabled: Circular buffer enabled

PINC

Bit 6: Peripheral increment mode.

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

MINC

Bit 7: Memory increment mode.

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

PSIZE

Bits 8-9: Peripheral size.

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

MSIZE

Bits 10-11: Memory size.

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

PL

Bits 12-13: Channel Priority level.

Allowed values:
0: Low: Low priority
1: Medium: Medium priority
2: High: High priority
3: VeryHigh: Very high priority

MEM2MEM

Bit 14: Memory to memory mode.

Allowed values:
0: Disabled: Memory to memory mode disabled
1: Enabled: Memory to memory mode enabled

NDTR [3]

DMA channel 1 number of data register

Offset: 0x34, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
NDT rw

Toggle fields

NDT

Bits 0-15: Number of data to transfer.

Allowed values: 0x0-0xffff

PAR [3]

DMA channel 1 peripheral address register

Offset: 0x38, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PA rw

Toggle fields

PA

Bits 0-31: Peripheral address.

MAR [3]

DMA channel 1 memory address register

Offset: 0x3c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MA rw

Toggle fields

MA

Bits 0-31: Memory address.

CR [4]

DMA channel configuration register (DMA_CCR)

Offset: 0x44, size: 32, reset: 0x00000000, access: read-write

12/12 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	MEM2MEM rw	PL rw		MSIZE rw		PSIZE rw		MINC rw	PINC rw	CIRC rw	DIR rw	TEIE rw	HTIE rw	TCIE rw	EN rw

Toggle fields

EN

Bit 0: Channel enable.

Allowed values:
0: Disabled: Channel disabled
1: Enabled: Channel enabled

TCIE

Bit 1: Transfer complete interrupt enable.

Allowed values:
0: Disabled: Transfer Complete interrupt disabled
1: Enabled: Transfer Complete interrupt enabled

HTIE

Bit 2: Half Transfer interrupt enable.

Allowed values:
0: Disabled: Half Transfer interrupt disabled
1: Enabled: Half Transfer interrupt enabled

TEIE

Bit 3: Transfer error interrupt enable.

Allowed values:
0: Disabled: Transfer Error interrupt disabled
1: Enabled: Transfer Error interrupt enabled

DIR

Bit 4: Data transfer direction.

Allowed values:
0: FromPeripheral: Read from peripheral
1: FromMemory: Read from memory

CIRC

Bit 5: Circular mode.

Allowed values:
0: Disabled: Circular buffer disabled
1: Enabled: Circular buffer enabled

PINC

Bit 6: Peripheral increment mode.

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

MINC

Bit 7: Memory increment mode.

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

PSIZE

Bits 8-9: Peripheral size.

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

MSIZE

Bits 10-11: Memory size.

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

PL

Bits 12-13: Channel Priority level.

Allowed values:
0: Low: Low priority
1: Medium: Medium priority
2: High: High priority
3: VeryHigh: Very high priority

MEM2MEM

Bit 14: Memory to memory mode.

Allowed values:
0: Disabled: Memory to memory mode disabled
1: Enabled: Memory to memory mode enabled

NDTR [4]

DMA channel 1 number of data register

Offset: 0x48, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
NDT rw

Toggle fields

NDT

Bits 0-15: Number of data to transfer.

Allowed values: 0x0-0xffff

PAR [4]

DMA channel 1 peripheral address register

Offset: 0x4c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PA rw

Toggle fields

PA

Bits 0-31: Peripheral address.

MAR [4]

DMA channel 1 memory address register

Offset: 0x50, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MA rw

Toggle fields

MA

Bits 0-31: Memory address.

CR [5]

DMA channel configuration register (DMA_CCR)

Offset: 0x58, size: 32, reset: 0x00000000, access: read-write

12/12 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	MEM2MEM rw	PL rw		MSIZE rw		PSIZE rw		MINC rw	PINC rw	CIRC rw	DIR rw	TEIE rw	HTIE rw	TCIE rw	EN rw

Toggle fields

EN

Bit 0: Channel enable.

Allowed values:
0: Disabled: Channel disabled
1: Enabled: Channel enabled

TCIE

Bit 1: Transfer complete interrupt enable.

Allowed values:
0: Disabled: Transfer Complete interrupt disabled
1: Enabled: Transfer Complete interrupt enabled

HTIE

Bit 2: Half Transfer interrupt enable.

Allowed values:
0: Disabled: Half Transfer interrupt disabled
1: Enabled: Half Transfer interrupt enabled

TEIE

Bit 3: Transfer error interrupt enable.

Allowed values:
0: Disabled: Transfer Error interrupt disabled
1: Enabled: Transfer Error interrupt enabled

DIR

Bit 4: Data transfer direction.

Allowed values:
0: FromPeripheral: Read from peripheral
1: FromMemory: Read from memory

CIRC

Bit 5: Circular mode.

Allowed values:
0: Disabled: Circular buffer disabled
1: Enabled: Circular buffer enabled

PINC

Bit 6: Peripheral increment mode.

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

MINC

Bit 7: Memory increment mode.

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

PSIZE

Bits 8-9: Peripheral size.

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

MSIZE

Bits 10-11: Memory size.

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

PL

Bits 12-13: Channel Priority level.

Allowed values:
0: Low: Low priority
1: Medium: Medium priority
2: High: High priority
3: VeryHigh: Very high priority

MEM2MEM

Bit 14: Memory to memory mode.

Allowed values:
0: Disabled: Memory to memory mode disabled
1: Enabled: Memory to memory mode enabled

NDTR [5]

DMA channel 1 number of data register

Offset: 0x5c, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
NDT rw

Toggle fields

NDT

Bits 0-15: Number of data to transfer.

Allowed values: 0x0-0xffff

PAR [5]

DMA channel 1 peripheral address register

Offset: 0x60, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PA rw

Toggle fields

PA

Bits 0-31: Peripheral address.

MAR [5]

DMA channel 1 memory address register

Offset: 0x64, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MA rw

Toggle fields

MA

Bits 0-31: Memory address.

CR [6]

DMA channel configuration register (DMA_CCR)

Offset: 0x6c, size: 32, reset: 0x00000000, access: read-write

12/12 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	MEM2MEM rw	PL rw		MSIZE rw		PSIZE rw		MINC rw	PINC rw	CIRC rw	DIR rw	TEIE rw	HTIE rw	TCIE rw	EN rw

Toggle fields

EN

Bit 0: Channel enable.

Allowed values:
0: Disabled: Channel disabled
1: Enabled: Channel enabled

TCIE

Bit 1: Transfer complete interrupt enable.

Allowed values:
0: Disabled: Transfer Complete interrupt disabled
1: Enabled: Transfer Complete interrupt enabled

HTIE

Bit 2: Half Transfer interrupt enable.

Allowed values:
0: Disabled: Half Transfer interrupt disabled
1: Enabled: Half Transfer interrupt enabled

TEIE

Bit 3: Transfer error interrupt enable.

Allowed values:
0: Disabled: Transfer Error interrupt disabled
1: Enabled: Transfer Error interrupt enabled

DIR

Bit 4: Data transfer direction.

Allowed values:
0: FromPeripheral: Read from peripheral
1: FromMemory: Read from memory

CIRC

Bit 5: Circular mode.

Allowed values:
0: Disabled: Circular buffer disabled
1: Enabled: Circular buffer enabled

PINC

Bit 6: Peripheral increment mode.

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

MINC

Bit 7: Memory increment mode.

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

PSIZE

Bits 8-9: Peripheral size.

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

MSIZE

Bits 10-11: Memory size.

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

PL

Bits 12-13: Channel Priority level.

Allowed values:
0: Low: Low priority
1: Medium: Medium priority
2: High: High priority
3: VeryHigh: Very high priority

MEM2MEM

Bit 14: Memory to memory mode.

Allowed values:
0: Disabled: Memory to memory mode disabled
1: Enabled: Memory to memory mode enabled

NDTR [6]

DMA channel 1 number of data register

Offset: 0x70, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
NDT rw

Toggle fields

NDT

Bits 0-15: Number of data to transfer.

Allowed values: 0x0-0xffff

PAR [6]

DMA channel 1 peripheral address register

Offset: 0x74, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PA rw

Toggle fields

PA

Bits 0-31: Peripheral address.

MAR [6]

DMA channel 1 memory address register

Offset: 0x78, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MA rw

Toggle fields

MA

Bits 0-31: Memory address.

CR [7]

DMA channel configuration register (DMA_CCR)

Offset: 0x80, size: 32, reset: 0x00000000, access: read-write

12/12 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	MEM2MEM rw	PL rw		MSIZE rw		PSIZE rw		MINC rw	PINC rw	CIRC rw	DIR rw	TEIE rw	HTIE rw	TCIE rw	EN rw

Toggle fields

EN

Bit 0: Channel enable.

Allowed values:
0: Disabled: Channel disabled
1: Enabled: Channel enabled

TCIE

Bit 1: Transfer complete interrupt enable.

Allowed values:
0: Disabled: Transfer Complete interrupt disabled
1: Enabled: Transfer Complete interrupt enabled

HTIE

Bit 2: Half Transfer interrupt enable.

Allowed values:
0: Disabled: Half Transfer interrupt disabled
1: Enabled: Half Transfer interrupt enabled

TEIE

Bit 3: Transfer error interrupt enable.

Allowed values:
0: Disabled: Transfer Error interrupt disabled
1: Enabled: Transfer Error interrupt enabled

DIR

Bit 4: Data transfer direction.

Allowed values:
0: FromPeripheral: Read from peripheral
1: FromMemory: Read from memory

CIRC

Bit 5: Circular mode.

Allowed values:
0: Disabled: Circular buffer disabled
1: Enabled: Circular buffer enabled

PINC

Bit 6: Peripheral increment mode.

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

MINC

Bit 7: Memory increment mode.

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

PSIZE

Bits 8-9: Peripheral size.

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

MSIZE

Bits 10-11: Memory size.

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

PL

Bits 12-13: Channel Priority level.

Allowed values:
0: Low: Low priority
1: Medium: Medium priority
2: High: High priority
3: VeryHigh: Very high priority

MEM2MEM

Bit 14: Memory to memory mode.

Allowed values:
0: Disabled: Memory to memory mode disabled
1: Enabled: Memory to memory mode enabled

NDTR [7]

DMA channel 1 number of data register

Offset: 0x84, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
NDT rw

Toggle fields

NDT

Bits 0-15: Number of data to transfer.

Allowed values: 0x0-0xffff

PAR [7]

DMA channel 1 peripheral address register

Offset: 0x88, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PA rw

Toggle fields

PA

Bits 0-31: Peripheral address.

MAR [7]

DMA channel 1 memory address register

Offset: 0x8c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MA rw

Toggle fields

MA

Bits 0-31: Memory address.

EXTI

0x40010400: External interrupt/event controller

184/184 fields covered.

Toggle register map

Offset	Name	31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	IMR1	MR31	MR30	MR29	MR28	MR27	MR26	MR25	MR24	MR23	MR22	MR21	MR20	MR19	MR18	MR17	MR16	MR15	MR14	MR13	MR12	MR11	MR10	MR9	MR8	MR7	MR6	MR5	MR4	MR3	MR2	MR1	MR0
0x4	EMR1	MR31	MR30	MR29	MR28	MR27	MR26	MR25	MR24	MR23	MR22	MR21	MR20	MR19	MR18	MR17	MR16	MR15	MR14	MR13	MR12	MR11	MR10	MR9	MR8	MR7	MR6	MR5	MR4	MR3	MR2	MR1	MR0
0x8	RTSR1	TR31	TR30	TR29							TR22	TR21	TR20	TR19	TR18	TR17	TR16	TR15	TR14	TR13	TR12	TR11	TR10	TR9	TR8	TR7	TR6	TR5	TR4	TR3	TR2	TR1	TR0
0xc	FTSR1	TR31	TR30	TR29							TR22	TR21	TR20	TR19	TR18	TR17	TR16	TR15	TR14	TR13	TR12	TR11	TR10	TR9	TR8	TR7	TR6	TR5	TR4	TR3	TR2	TR1	TR0
0x10	SWIER1	SWIER31	SWIER30	SWIER29							SWIER22	SWIER21	SWIER20	SWIER19	SWIER18	SWIER17	SWIER16	SWIER15	SWIER14	SWIER13	SWIER12	SWIER11	SWIER10	SWIER9	SWIER8	SWIER7	SWIER6	SWIER5	SWIER4	SWIER3	SWIER2	SWIER1	SWIER0
0x14	PR1	PR31	PR30	PR29							PR22	PR21	PR20	PR19	PR18	PR17	PR16	PR15	PR14	PR13	PR12	PR11	PR10	PR9	PR8	PR7	PR6	PR5	PR4	PR3	PR2	PR1	PR0
0x20	IMR2																													MR35	MR34	MR33	MR32
0x24	EMR2																													MR35	MR34	MR33	MR32
0x28	RTSR2																															TR33	TR32
0x2c	FTSR2																															TR33	TR32
0x30	SWIER2																															SWIER33	SWIER32
0x34	PR2																															PR33	PR32

Toggle registers

IMR1

Interrupt mask register

Offset: 0x0, size: 32, reset: 0x1F800000, access: read-write

32/32 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MR31 rw	MR30 rw	MR29 rw	MR28 rw	MR27 rw	MR26 rw	MR25 rw	MR24 rw	MR23 rw	MR22 rw	MR21 rw	MR20 rw	MR19 rw	MR18 rw	MR17 rw	MR16 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MR15 rw	MR14 rw	MR13 rw	MR12 rw	MR11 rw	MR10 rw	MR9 rw	MR8 rw	MR7 rw	MR6 rw	MR5 rw	MR4 rw	MR3 rw	MR2 rw	MR1 rw	MR0 rw

Toggle fields

MR0

Bit 0: Interrupt Mask on line 0.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR1

Bit 1: Interrupt Mask on line 1.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR2

Bit 2: Interrupt Mask on line 2.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR3

Bit 3: Interrupt Mask on line 3.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR4

Bit 4: Interrupt Mask on line 4.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR5

Bit 5: Interrupt Mask on line 5.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR6

Bit 6: Interrupt Mask on line 6.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR7

Bit 7: Interrupt Mask on line 7.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR8

Bit 8: Interrupt Mask on line 8.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR9

Bit 9: Interrupt Mask on line 9.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR10

Bit 10: Interrupt Mask on line 10.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR11

Bit 11: Interrupt Mask on line 11.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR12

Bit 12: Interrupt Mask on line 12.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR13

Bit 13: Interrupt Mask on line 13.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR14

Bit 14: Interrupt Mask on line 14.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR15

Bit 15: Interrupt Mask on line 15.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR16

Bit 16: Interrupt Mask on line 16.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR17

Bit 17: Interrupt Mask on line 17.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR18

Bit 18: Interrupt Mask on line 18.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR19

Bit 19: Interrupt Mask on line 19.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR20

Bit 20: Interrupt Mask on line 20.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR21

Bit 21: Interrupt Mask on line 21.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR22

Bit 22: Interrupt Mask on line 22.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR23

Bit 23: Interrupt Mask on line 23.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR24

Bit 24: Interrupt Mask on line 24.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR25

Bit 25: Interrupt Mask on line 25.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR26

Bit 26: Interrupt Mask on line 26.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR27

Bit 27: Interrupt Mask on line 27.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR28

Bit 28: Interrupt Mask on line 28.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR29

Bit 29: Interrupt Mask on line 29.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR30

Bit 30: Interrupt Mask on line 30.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR31

Bit 31: Interrupt Mask on line 31.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

EMR1

Event mask register

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

32/32 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MR31 rw	MR30 rw	MR29 rw	MR28 rw	MR27 rw	MR26 rw	MR25 rw	MR24 rw	MR23 rw	MR22 rw	MR21 rw	MR20 rw	MR19 rw	MR18 rw	MR17 rw	MR16 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MR15 rw	MR14 rw	MR13 rw	MR12 rw	MR11 rw	MR10 rw	MR9 rw	MR8 rw	MR7 rw	MR6 rw	MR5 rw	MR4 rw	MR3 rw	MR2 rw	MR1 rw	MR0 rw

Toggle fields

MR0

Bit 0: Event Mask on line 0.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR1

Bit 1: Event Mask on line 1.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR2

Bit 2: Event Mask on line 2.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR3

Bit 3: Event Mask on line 3.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR4

Bit 4: Event Mask on line 4.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR5

Bit 5: Event Mask on line 5.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR6

Bit 6: Event Mask on line 6.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR7

Bit 7: Event Mask on line 7.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR8

Bit 8: Event Mask on line 8.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR9

Bit 9: Event Mask on line 9.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR10

Bit 10: Event Mask on line 10.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR11

Bit 11: Event Mask on line 11.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR12

Bit 12: Event Mask on line 12.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR13

Bit 13: Event Mask on line 13.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR14

Bit 14: Event Mask on line 14.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR15

Bit 15: Event Mask on line 15.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR16

Bit 16: Event Mask on line 16.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR17

Bit 17: Event Mask on line 17.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR18

Bit 18: Event Mask on line 18.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR19

Bit 19: Event Mask on line 19.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR20

Bit 20: Event Mask on line 20.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR21

Bit 21: Event Mask on line 21.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR22

Bit 22: Event Mask on line 22.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR23

Bit 23: Event Mask on line 23.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR24

Bit 24: Event Mask on line 24.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR25

Bit 25: Event Mask on line 25.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR26

Bit 26: Event Mask on line 26.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR27

Bit 27: Event Mask on line 27.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR28

Bit 28: Event Mask on line 28.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR29

Bit 29: Event Mask on line 29.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR30

Bit 30: Event Mask on line 30.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR31

Bit 31: Event Mask on line 31.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

RTSR1

Rising Trigger selection register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

26/26 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
TR31 rw	TR30 rw	TR29 rw							TR22 rw	TR21 rw	TR20 rw	TR19 rw	TR18 rw	TR17 rw	TR16 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TR15 rw	TR14 rw	TR13 rw	TR12 rw	TR11 rw	TR10 rw	TR9 rw	TR8 rw	TR7 rw	TR6 rw	TR5 rw	TR4 rw	TR3 rw	TR2 rw	TR1 rw	TR0 rw

Toggle fields

TR0

Bit 0: Rising trigger event configuration of line 0.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR1

Bit 1: Rising trigger event configuration of line 1.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR2

Bit 2: Rising trigger event configuration of line 2.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR3

Bit 3: Rising trigger event configuration of line 3.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR4

Bit 4: Rising trigger event configuration of line 4.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR5

Bit 5: Rising trigger event configuration of line 5.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR6

Bit 6: Rising trigger event configuration of line 6.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR7

Bit 7: Rising trigger event configuration of line 7.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR8

Bit 8: Rising trigger event configuration of line 8.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR9

Bit 9: Rising trigger event configuration of line 9.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR10

Bit 10: Rising trigger event configuration of line 10.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR11

Bit 11: Rising trigger event configuration of line 11.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR12

Bit 12: Rising trigger event configuration of line 12.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR13

Bit 13: Rising trigger event configuration of line 13.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR14

Bit 14: Rising trigger event configuration of line 14.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR15

Bit 15: Rising trigger event configuration of line 15.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR16

Bit 16: Rising trigger event configuration of line 16.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR17

Bit 17: Rising trigger event configuration of line 17.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR18

Bit 18: Rising trigger event configuration of line 18.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR19

Bit 19: Rising trigger event configuration of line 19.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR20

Bit 20: Rising trigger event configuration of line 20.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR21

Bit 21: Rising trigger event configuration of line 21.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR22

Bit 22: Rising trigger event configuration of line 22.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR29

Bit 29: Rising trigger event configuration of line 29.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR30

Bit 30: Rising trigger event configuration of line 30.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR31

Bit 31: Rising trigger event configuration of line 31.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

FTSR1

Falling Trigger selection register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

26/26 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
TR31 rw	TR30 rw	TR29 rw							TR22 rw	TR21 rw	TR20 rw	TR19 rw	TR18 rw	TR17 rw	TR16 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TR15 rw	TR14 rw	TR13 rw	TR12 rw	TR11 rw	TR10 rw	TR9 rw	TR8 rw	TR7 rw	TR6 rw	TR5 rw	TR4 rw	TR3 rw	TR2 rw	TR1 rw	TR0 rw

Toggle fields

TR0

Bit 0: Falling trigger event configuration of line 0.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR1

Bit 1: Falling trigger event configuration of line 1.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR2

Bit 2: Falling trigger event configuration of line 2.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR3

Bit 3: Falling trigger event configuration of line 3.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR4

Bit 4: Falling trigger event configuration of line 4.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR5

Bit 5: Falling trigger event configuration of line 5.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR6

Bit 6: Falling trigger event configuration of line 6.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR7

Bit 7: Falling trigger event configuration of line 7.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR8

Bit 8: Falling trigger event configuration of line 8.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR9

Bit 9: Falling trigger event configuration of line 9.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR10

Bit 10: Falling trigger event configuration of line 10.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR11

Bit 11: Falling trigger event configuration of line 11.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR12

Bit 12: Falling trigger event configuration of line 12.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR13

Bit 13: Falling trigger event configuration of line 13.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR14

Bit 14: Falling trigger event configuration of line 14.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR15

Bit 15: Falling trigger event configuration of line 15.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR16

Bit 16: Falling trigger event configuration of line 16.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR17

Bit 17: Falling trigger event configuration of line 17.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR18

Bit 18: Falling trigger event configuration of line 18.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR19

Bit 19: Falling trigger event configuration of line 19.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR20

Bit 20: Falling trigger event configuration of line 20.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR21

Bit 21: Falling trigger event configuration of line 21.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR22

Bit 22: Falling trigger event configuration of line 22.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR29

Bit 29: Falling trigger event configuration of line 29.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR30

Bit 30: Falling trigger event configuration of line 30..

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR31

Bit 31: Falling trigger event configuration of line 31.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

SWIER1

Software interrupt event register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

26/26 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
SWIER31 rw	SWIER30 rw	SWIER29 rw							SWIER22 rw	SWIER21 rw	SWIER20 rw	SWIER19 rw	SWIER18 rw	SWIER17 rw	SWIER16 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SWIER15 rw	SWIER14 rw	SWIER13 rw	SWIER12 rw	SWIER11 rw	SWIER10 rw	SWIER9 rw	SWIER8 rw	SWIER7 rw	SWIER6 rw	SWIER5 rw	SWIER4 rw	SWIER3 rw	SWIER2 rw	SWIER1 rw	SWIER0 rw

Toggle fields

SWIER0

Bit 0: Software Interrupt on line 0.

Allowed values:
1: Pend: Generates an interrupt request

SWIER1

Bit 1: Software Interrupt on line 1.

Allowed values:
1: Pend: Generates an interrupt request

SWIER2

Bit 2: Software Interrupt on line 2.

Allowed values:
1: Pend: Generates an interrupt request

SWIER3

Bit 3: Software Interrupt on line 3.

Allowed values:
1: Pend: Generates an interrupt request

SWIER4

Bit 4: Software Interrupt on line 4.

Allowed values:
1: Pend: Generates an interrupt request

SWIER5

Bit 5: Software Interrupt on line 5.

Allowed values:
1: Pend: Generates an interrupt request

SWIER6

Bit 6: Software Interrupt on line 6.

Allowed values:
1: Pend: Generates an interrupt request

SWIER7

Bit 7: Software Interrupt on line 7.

Allowed values:
1: Pend: Generates an interrupt request

SWIER8

Bit 8: Software Interrupt on line 8.

Allowed values:
1: Pend: Generates an interrupt request

SWIER9

Bit 9: Software Interrupt on line 9.

Allowed values:
1: Pend: Generates an interrupt request

SWIER10

Bit 10: Software Interrupt on line 10.

Allowed values:
1: Pend: Generates an interrupt request

SWIER11

Bit 11: Software Interrupt on line 11.

Allowed values:
1: Pend: Generates an interrupt request

SWIER12

Bit 12: Software Interrupt on line 12.

Allowed values:
1: Pend: Generates an interrupt request

SWIER13

Bit 13: Software Interrupt on line 13.

Allowed values:
1: Pend: Generates an interrupt request

SWIER14

Bit 14: Software Interrupt on line 14.

Allowed values:
1: Pend: Generates an interrupt request

SWIER15

Bit 15: Software Interrupt on line 15.

Allowed values:
1: Pend: Generates an interrupt request

SWIER16

Bit 16: Software Interrupt on line 16.

Allowed values:
1: Pend: Generates an interrupt request

SWIER17

Bit 17: Software Interrupt on line 17.

Allowed values:
1: Pend: Generates an interrupt request

SWIER18

Bit 18: Software Interrupt on line 18.

Allowed values:
1: Pend: Generates an interrupt request

SWIER19

Bit 19: Software Interrupt on line 19.

Allowed values:
1: Pend: Generates an interrupt request

SWIER20

Bit 20: Software Interrupt on line 20.

Allowed values:
1: Pend: Generates an interrupt request

SWIER21

Bit 21: Software Interrupt on line 21.

Allowed values:
1: Pend: Generates an interrupt request

SWIER22

Bit 22: Software Interrupt on line 22.

Allowed values:
1: Pend: Generates an interrupt request

SWIER29

Bit 29: Software Interrupt on line 29.

Allowed values:
1: Pend: Generates an interrupt request

SWIER30

Bit 30: Software Interrupt on line 309.

Allowed values:
1: Pend: Generates an interrupt request

SWIER31

Bit 31: Software Interrupt on line 319.

Allowed values:
1: Pend: Generates an interrupt request

PR1

Pending register

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

26/26 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PR31 rw	PR30 rw	PR29 rw							PR22 rw	PR21 rw	PR20 rw	PR19 rw	PR18 rw	PR17 rw	PR16 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PR15 rw	PR14 rw	PR13 rw	PR12 rw	PR11 rw	PR10 rw	PR9 rw	PR8 rw	PR7 rw	PR6 rw	PR5 rw	PR4 rw	PR3 rw	PR2 rw	PR1 rw	PR0 rw

Toggle fields

PR0

Bit 0: Pending bit 0.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR1

Bit 1: Pending bit 1.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR2

Bit 2: Pending bit 2.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR3

Bit 3: Pending bit 3.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR4

Bit 4: Pending bit 4.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR5

Bit 5: Pending bit 5.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR6

Bit 6: Pending bit 6.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR7

Bit 7: Pending bit 7.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR8

Bit 8: Pending bit 8.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR9

Bit 9: Pending bit 9.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR10

Bit 10: Pending bit 10.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR11

Bit 11: Pending bit 11.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR12

Bit 12: Pending bit 12.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR13

Bit 13: Pending bit 13.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR14

Bit 14: Pending bit 14.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR15

Bit 15: Pending bit 15.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR16

Bit 16: Pending bit 16.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR17

Bit 17: Pending bit 17.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR18

Bit 18: Pending bit 18.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR19

Bit 19: Pending bit 19.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR20

Bit 20: Pending bit 20.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR21

Bit 21: Pending bit 21.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR22

Bit 22: Pending bit 22.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR29

Bit 29: Pending bit 29.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR30

Bit 30: Pending bit 30.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR31

Bit 31: Pending bit 31.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

IMR2

Interrupt mask register

Offset: 0x20, size: 32, reset: 0xFFFFFFFC, access: read-write

4/4 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
												MR35 rw	MR34 rw	MR33 rw	MR32 rw

Toggle fields

MR32

Bit 0: Interrupt Mask on external/internal line 32.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR33

Bit 1: Interrupt Mask on external/internal line 33.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR34

Bit 2: Interrupt Mask on external/internal line 34.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR35

Bit 3: Interrupt Mask on external/internal line 35.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

EMR2

Event mask register

Offset: 0x24, size: 32, reset: 0x00000000, access: read-write

4/4 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
												MR35 rw	MR34 rw	MR33 rw	MR32 rw

Toggle fields

MR32

Bit 0: Event mask on external/internal line 32.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR33

Bit 1: Event mask on external/internal line 33.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR34

Bit 2: Event mask on external/internal line 34.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR35

Bit 3: Event mask on external/internal line 35.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

RTSR2

Rising Trigger selection register

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														TR33 rw	TR32 rw

Toggle fields

TR32

Bit 0: Rising trigger event configuration bit of line 32.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR33

Bit 1: Rising trigger event configuration bit of line 33.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

FTSR2

Falling Trigger selection register

Offset: 0x2c, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														TR33 rw	TR32 rw

Toggle fields

TR32

Bit 0: Falling trigger event configuration bit of line 32.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR33

Bit 1: Falling trigger event configuration bit of line 33.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

SWIER2

Software interrupt event register

Offset: 0x30, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														SWIER33 rw	SWIER32 rw

Toggle fields

SWIER32

Bit 0: Software interrupt on line 32.

Allowed values:
1: Pend: Generates an interrupt request

SWIER33

Bit 1: Software interrupt on line 33.

Allowed values:
1: Pend: Generates an interrupt request

PR2

Pending register

Offset: 0x34, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														PR33 rw	PR32 rw

Toggle fields

PR32

Bit 0: Pending bit on line 32.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PR33

Bit 1: Pending bit on line 33.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

FLASH

0x40022000: Flash

33/33 fields covered.

Toggle register map

Offset	Name	31	23	15	14	13	12	10	9	8	7	6	5	4	3	2	1	0
0x0	ACR												PRFTBS	PRFTBE	HLFCYA	LATENCY
0x4	KEYR	FKEYR		FKEYR
0x8	OPTKEYR	OPTKEYR		OPTKEYR
0xc	SR												EOP	WRPRTERR		PGERR		BSY
0x10	CR					OBL_LAUNCH	EOPIE	ERRIE	OPTWRE		LOCK	STRT	OPTER	OPTPG		MER	PER	PG
0x14	AR	FAR		FAR
0x1c	OBR	Data1	Data0		SRAM_PARITY_CHECK	VDDA_MONITOR	nBOOT1	nRST_STDBY	nRST_STOP	WDG_SW						RDPRT		OPTERR
0x20	WRPR	WRP		WRP

Toggle registers

ACR

Flash access control register

Offset: 0x0, size: 32, reset: 0x00000030, access: Unspecified

4/4 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
										PRFTBS r	PRFTBE rw	HLFCYA rw	LATENCY rw

Toggle fields

LATENCY

Bits 0-2: LATENCY.

Allowed values:
0: WS0: 0 wait states, if 0 < HCLK <= 24 MHz
1: WS1: 1 wait state, if 24 < HCLK <= 48 MHz
2: WS2: 2 wait states, if 48 < HCLK <= 72 MHz

HLFCYA

Bit 3: Flash half cycle access enable.

Allowed values:
0: Disabled: Half cycle is disabled
1: Enabled: Half cycle is enabled

PRFTBE

Bit 4: PRFTBE.

Allowed values:
0: Disabled: Prefetch is disabled
1: Enabled: Prefetch is enabled

PRFTBS

Bit 5: PRFTBS.

Allowed values:
0: Disabled: Prefetch buffer is disabled
1: Enabled: Prefetch buffer is enabled

KEYR

Flash key register

Offset: 0x4, size: 32, reset: 0x00000000, access: write-only

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FKEYR w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FKEYR w

Toggle fields

FKEYR

Bits 0-31: Flash Key.

Allowed values: 0x0-0xffffffff

OPTKEYR

Flash option key register

Offset: 0x8, size: 32, reset: 0x00000000, access: write-only

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OPTKEYR w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OPTKEYR w

Toggle fields

OPTKEYR

Bits 0-31: Option byte key.

Allowed values: 0x0-0xffffffff

SR

Flash status register

Offset: 0xc, size: 32, reset: 0x00000000, access: Unspecified

4/4 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
										EOP rw	WRPRTERR rw		PGERR rw		BSY r

Toggle fields

BSY

Bit 0: Busy.

Allowed values:
0: Inactive: No write/erase operation is in progress
1: Active: No write/erase operation is in progress

PGERR

Bit 2: Programming error.

Allowed values:
0: NoError: No programming error occurred
1: Error: A programming error occurred

WRPRTERR

Bit 4: Write protection error.

Allowed values:
0: NoError: No write protection error occurred
1: Error: A write protection error occurred

EOP

Bit 5: End of operation.

Allowed values:
0: NoEvent: No EOP event occurred
1: Event: An EOP event occurred

CR

Flash control register

Offset: 0x10, size: 32, reset: 0x00000080, access: read-write

11/11 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		OBL_LAUNCH rw	EOPIE rw		ERRIE rw	OPTWRE rw		LOCK rw	STRT rw	OPTER rw	OPTPG rw		MER rw	PER rw	PG rw

Toggle fields

PG

Bit 0: Programming.

Allowed values:
1: Program: Flash programming activated

PER

Bit 1: Page erase.

Allowed values:
1: PageErase: Erase activated for selected page

MER

Bit 2: Mass erase.

Allowed values:
1: MassErase: Erase activated for all user sectors

OPTPG

Bit 4: Option byte programming.

Allowed values:
1: OptionByteProgramming: Program option byte activated

OPTER

Bit 5: Option byte erase.

Allowed values:
1: OptionByteErase: Erase option byte activated

STRT

Bit 6: Start.

Allowed values:
1: Start: Trigger an erase operation

LOCK

Bit 7: Lock.

Allowed values:
0: Unlocked: FLASH_CR register is unlocked
1: Locked: FLASH_CR register is locked

OPTWRE

Bit 9: Option bytes write enable.

Allowed values:
0: Disabled: Option byte write enabled
1: Enabled: Option byte write disabled

ERRIE

Bit 10: Error interrupt enable.

Allowed values:
0: Disabled: Error interrupt generation disabled
1: Enabled: Error interrupt generation enabled

EOPIE

Bit 12: End of operation interrupt enable.

Allowed values:
0: Disabled: End of operation interrupt disabled
1: Enabled: End of operation interrupt enabled

OBL_LAUNCH

Bit 13: Force option byte loading.

Allowed values:
0: Inactive: Force option byte loading inactive
1: Active: Force option byte loading active

AR

Flash address register

Offset: 0x14, size: 32, reset: 0x00000000, access: write-only

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FAR w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FAR w

Toggle fields

FAR

Bits 0-31: Flash address.

Allowed values: 0x0-0xffffffff

OBR

Option byte register

Offset: 0x1c, size: 32, reset: 0xFFFFFF0F, access: read-only

10/10 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
Data1 r								Data0 r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	SRAM_PARITY_CHECK r	VDDA_MONITOR r	nBOOT1 r		nRST_STDBY r	nRST_STOP r	WDG_SW r						RDPRT r		OPTERR r

Toggle fields

OPTERR

Bit 0: Option byte error.

Allowed values:
1: OptionByteError: The loaded option byte and its complement do not match

RDPRT

Bits 1-2: Read protection Level status.

Allowed values:
0: Level0: Level 0
1: Level1: Level 1
3: Level2: Level 2

WDG_SW

Bit 8: WDG_SW.

Allowed values:
0: Hardware: Hardware watchdog
1: Software: Software watchdog

nRST_STOP

Bit 9: nRST_STOP.

Allowed values:
0: Reset: Reset generated when entering Stop mode
1: NoReset: No reset generated

nRST_STDBY

Bit 10: nRST_STDBY.

Allowed values:
0: Reset: Reset generated when entering Standby mode
1: NoReset: No reset generated

nBOOT1

Bit 12: BOOT1.

Allowed values:
0: Disabled: Together with BOOT0, select the device boot mode
1: Enabled: Together with BOOT0, select the device boot mode

VDDA_MONITOR

Bit 13: VDDA_MONITOR.

Allowed values:
0: Disabled: VDDA power supply supervisor disabled
1: Enabled: VDDA power supply supervisor enabled

SRAM_PARITY_CHECK

Bit 14: SRAM_PARITY_CHECK.

Allowed values:
0: Disabled: RAM parity check disabled
1: Enabled: RAM parity check enabled

Data0

Bits 16-23: Data0.

Allowed values: 0x0-0xff

Data1

Bits 24-31: Data1.

Allowed values: 0x0-0xff

WRPR

Write protection register

Offset: 0x20, size: 32, reset: 0xFFFFFFFF, access: read-only

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
WRP r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
WRP r

Toggle fields

WRP

Bits 0-31: Write protect.

Allowed values: 0x0-0xffffffff

FMC

0xa0000400: Flexible memory controller

5/187 fields covered.

Toggle register map

Offset	Name	31	29	27	23	20	19	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	BCR1					CCLKEN	CBURSTRW		ASYNCWAIT	EXTMOD	WAITEN	WREN	WAITCFG		WAITPOL	BURSTEN		FACCEN	MWID		MTYP		MUXEN	MBKEN
0x4	BTR1		ACCMOD	DATLAT	CLKDIV		BUSTURN		DATAST								ADDHLD				ADDSET
0x8	BCR2						CBURSTRW		ASYNCWAIT	EXTMOD	WAITEN	WREN	WAITCFG	WRAPMOD	WAITPOL	BURSTEN		FACCEN	MWID		MTYP		MUXEN	MBKEN
0xc	BTR2		ACCMOD	DATLAT	CLKDIV		BUSTURN		DATAST								ADDHLD				ADDSET
0x10	BCR3						CBURSTRW		ASYNCWAIT	EXTMOD	WAITEN	WREN	WAITCFG	WRAPMOD	WAITPOL	BURSTEN		FACCEN	MWID		MTYP		MUXEN	MBKEN
0x14	BTR3		ACCMOD	DATLAT	CLKDIV		BUSTURN		DATAST								ADDHLD				ADDSET
0x18	BCR4						CBURSTRW		ASYNCWAIT	EXTMOD	WAITEN	WREN	WAITCFG	WRAPMOD	WAITPOL	BURSTEN		FACCEN	MWID		MTYP		MUXEN	MBKEN
0x1c	BTR4		ACCMOD	DATLAT	CLKDIV		BUSTURN		DATAST								ADDHLD				ADDSET
0x60	PCR2						ECCPS	TAR	TAR			TCLR						ECCEN	PWID		PTYP	PBKEN	PWAITEN
0x64	SR2																	FEMPT	IFEN	ILEN	IREN	IFS	ILS	IRS
0x68	PMEM2	MEMHIZx			MEMHOLDx				MEMWAITx								MEMSETx
0x6c	PATT2	ATTHIZx			ATTHOLDx				ATTWAITx								ATTSETx
0x74	ECCR2	ECCx							ECCx
0x80	PCR3						ECCPS	TAR	TAR			TCLR						ECCEN	PWID		PTYP	PBKEN	PWAITEN
0x84	SR3																	FEMPT	IFEN	ILEN	IREN	IFS	ILS	IRS
0x88	PMEM3	MEMHIZx			MEMHOLDx				MEMWAITx								MEMSETx
0x8c	PATT3	ATTHIZx			ATTHOLDx				ATTWAITx								ATTSETx
0x94	ECCR3	ECCx							ECCx
0xa0	PCR4						ECCPS	TAR	TAR			TCLR						ECCEN	PWID		PTYP	PBKEN	PWAITEN
0xa4	SR4																	FEMPT	IFEN	ILEN	IREN	IFS	ILS	IRS
0xa8	PMEM4	MEMHIZx			MEMHOLDx				MEMWAITx								MEMSETx
0xac	PATT4	ATTHIZx			ATTHOLDx				ATTWAITx								ATTSETx
0xb0	PIO4	IOHIZx			IOHOLDx				IOWAITx								IOSETx
0x104	BWTR1		ACCMOD	DATLAT	CLKDIV		BUSTURN		DATAST								ADDHLD				ADDSET
0x10c	BWTR2		ACCMOD	DATLAT	CLKDIV		BUSTURN		DATAST								ADDHLD				ADDSET
0x114	BWTR3		ACCMOD	DATLAT	CLKDIV		BUSTURN		DATAST								ADDHLD				ADDSET
0x11c	BWTR4		ACCMOD	DATLAT	CLKDIV		BUSTURN		DATAST								ADDHLD				ADDSET

Toggle registers

BCR1

SRAM/NOR-Flash chip-select control register 1

Offset: 0x0, size: 32, reset: 0x000030D0, access: read-write

0/14 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
											CCLKEN rw	CBURSTRW rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ASYNCWAIT rw	EXTMOD rw	WAITEN rw	WREN rw	WAITCFG rw		WAITPOL rw	BURSTEN rw		FACCEN rw	MWID rw		MTYP rw		MUXEN rw	MBKEN rw

Toggle fields

MBKEN

Bit 0: MBKEN.

MUXEN

Bit 1: MUXEN.

MTYP

Bits 2-3: MTYP.

MWID

Bits 4-5: MWID.

FACCEN

Bit 6: FACCEN.

BURSTEN

Bit 8: BURSTEN.

WAITPOL

Bit 9: WAITPOL.

WAITCFG

Bit 11: WAITCFG.

WREN

Bit 12: WREN.

WAITEN

Bit 13: WAITEN.

EXTMOD

Bit 14: EXTMOD.

ASYNCWAIT

Bit 15: ASYNCWAIT.

CBURSTRW

Bit 19: CBURSTRW.

CCLKEN

Bit 20: CCLKEN.

BTR1

SRAM/NOR-Flash chip-select timing register 1

Offset: 0x4, size: 32, reset: 0xFFFFFFFF, access: read-write

0/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
		ACCMOD rw		DATLAT rw				CLKDIV rw				BUSTURN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DATAST rw								ADDHLD rw				ADDSET rw

Toggle fields

ADDSET

Bits 0-3: ADDSET.

ADDHLD

Bits 4-7: ADDHLD.

DATAST

Bits 8-15: DATAST.

BUSTURN

Bits 16-19: BUSTURN.

CLKDIV

Bits 20-23: CLKDIV.

DATLAT

Bits 24-27: DATLAT.

ACCMOD

Bits 28-29: ACCMOD.

BCR2

SRAM/NOR-Flash chip-select control register 2

Offset: 0x8, size: 32, reset: 0x000030D0, access: read-write

0/14 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
												CBURSTRW rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ASYNCWAIT rw	EXTMOD rw	WAITEN rw	WREN rw	WAITCFG rw	WRAPMOD rw	WAITPOL rw	BURSTEN rw		FACCEN rw	MWID rw		MTYP rw		MUXEN rw	MBKEN rw

Toggle fields

MBKEN

Bit 0: MBKEN.

MUXEN

Bit 1: MUXEN.

MTYP

Bits 2-3: MTYP.

MWID

Bits 4-5: MWID.

FACCEN

Bit 6: FACCEN.

BURSTEN

Bit 8: BURSTEN.

WAITPOL

Bit 9: WAITPOL.

WRAPMOD

Bit 10: WRAPMOD.

WAITCFG

Bit 11: WAITCFG.

WREN

Bit 12: WREN.

WAITEN

Bit 13: WAITEN.

EXTMOD

Bit 14: EXTMOD.

ASYNCWAIT

Bit 15: ASYNCWAIT.

CBURSTRW

Bit 19: CBURSTRW.

BTR2

SRAM/NOR-Flash chip-select timing register 2

Offset: 0xc, size: 32, reset: 0xFFFFFFFF, access: read-write

0/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
		ACCMOD rw		DATLAT rw				CLKDIV rw				BUSTURN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DATAST rw								ADDHLD rw				ADDSET rw

Toggle fields

ADDSET

Bits 0-3: ADDSET.

ADDHLD

Bits 4-7: ADDHLD.

DATAST

Bits 8-15: DATAST.

BUSTURN

Bits 16-19: BUSTURN.

CLKDIV

Bits 20-23: CLKDIV.

DATLAT

Bits 24-27: DATLAT.

ACCMOD

Bits 28-29: ACCMOD.

BCR3

SRAM/NOR-Flash chip-select control register 3

Offset: 0x10, size: 32, reset: 0x000030D0, access: read-write

0/14 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
												CBURSTRW rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ASYNCWAIT rw	EXTMOD rw	WAITEN rw	WREN rw	WAITCFG rw	WRAPMOD rw	WAITPOL rw	BURSTEN rw		FACCEN rw	MWID rw		MTYP rw		MUXEN rw	MBKEN rw

Toggle fields

MBKEN

Bit 0: MBKEN.

MUXEN

Bit 1: MUXEN.

MTYP

Bits 2-3: MTYP.

MWID

Bits 4-5: MWID.

FACCEN

Bit 6: FACCEN.

BURSTEN

Bit 8: BURSTEN.

WAITPOL

Bit 9: WAITPOL.

WRAPMOD

Bit 10: WRAPMOD.

WAITCFG

Bit 11: WAITCFG.

WREN

Bit 12: WREN.

WAITEN

Bit 13: WAITEN.

EXTMOD

Bit 14: EXTMOD.

ASYNCWAIT

Bit 15: ASYNCWAIT.

CBURSTRW

Bit 19: CBURSTRW.

BTR3

SRAM/NOR-Flash chip-select timing register 3

Offset: 0x14, size: 32, reset: 0xFFFFFFFF, access: read-write

0/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
		ACCMOD rw		DATLAT rw				CLKDIV rw				BUSTURN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DATAST rw								ADDHLD rw				ADDSET rw

Toggle fields

ADDSET

Bits 0-3: ADDSET.

ADDHLD

Bits 4-7: ADDHLD.

DATAST

Bits 8-15: DATAST.

BUSTURN

Bits 16-19: BUSTURN.

CLKDIV

Bits 20-23: CLKDIV.

DATLAT

Bits 24-27: DATLAT.

ACCMOD

Bits 28-29: ACCMOD.

BCR4

SRAM/NOR-Flash chip-select control register 4

Offset: 0x18, size: 32, reset: 0x000030D0, access: read-write

0/14 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
												CBURSTRW rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ASYNCWAIT rw	EXTMOD rw	WAITEN rw	WREN rw	WAITCFG rw	WRAPMOD rw	WAITPOL rw	BURSTEN rw		FACCEN rw	MWID rw		MTYP rw		MUXEN rw	MBKEN rw

Toggle fields

MBKEN

Bit 0: MBKEN.

MUXEN

Bit 1: MUXEN.

MTYP

Bits 2-3: MTYP.

MWID

Bits 4-5: MWID.

FACCEN

Bit 6: FACCEN.

BURSTEN

Bit 8: BURSTEN.

WAITPOL

Bit 9: WAITPOL.

WRAPMOD

Bit 10: WRAPMOD.

WAITCFG

Bit 11: WAITCFG.

WREN

Bit 12: WREN.

WAITEN

Bit 13: WAITEN.

EXTMOD

Bit 14: EXTMOD.

ASYNCWAIT

Bit 15: ASYNCWAIT.

CBURSTRW

Bit 19: CBURSTRW.

BTR4

SRAM/NOR-Flash chip-select timing register 4

Offset: 0x1c, size: 32, reset: 0xFFFFFFFF, access: read-write

0/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
		ACCMOD rw		DATLAT rw				CLKDIV rw				BUSTURN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DATAST rw								ADDHLD rw				ADDSET rw

Toggle fields

ADDSET

Bits 0-3: ADDSET.

ADDHLD

Bits 4-7: ADDHLD.

DATAST

Bits 8-15: DATAST.

BUSTURN

Bits 16-19: BUSTURN.

CLKDIV

Bits 20-23: CLKDIV.

DATLAT

Bits 24-27: DATLAT.

ACCMOD

Bits 28-29: ACCMOD.

PCR2

PC Card/NAND Flash control register 2

Offset: 0x60, size: 32, reset: 0x00000018, access: read-write

0/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
												ECCPS rw			TAR rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TAR rw			TCLR rw						ECCEN rw	PWID rw		PTYP rw	PBKEN rw	PWAITEN rw

Toggle fields

PWAITEN

Bit 1: PWAITEN.

PBKEN

Bit 2: PBKEN.

PTYP

Bit 3: PTYP.

PWID

Bits 4-5: PWID.

ECCEN

Bit 6: ECCEN.

TCLR

Bits 9-12: TCLR.

TAR

Bits 13-16: TAR.

ECCPS

Bits 17-19: ECCPS.

SR2

FIFO status and interrupt register 2

Offset: 0x64, size: 32, reset: 0x00000040, access: Unspecified

1/7 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
									FEMPT r	IFEN rw	ILEN rw	IREN rw	IFS rw	ILS rw	IRS rw

Toggle fields

IRS

Bit 0: IRS.

ILS

Bit 1: ILS.

IFS

Bit 2: IFS.

IREN

Bit 3: IREN.

ILEN

Bit 4: ILEN.

IFEN

Bit 5: IFEN.

FEMPT

Bit 6: FEMPT.

PMEM2

Common memory space timing register 2

Offset: 0x68, size: 32, reset: 0xFCFCFCFC, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MEMHIZx rw								MEMHOLDx rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MEMWAITx rw								MEMSETx rw

Toggle fields

MEMSETx

Bits 0-7: MEMSETx.

MEMWAITx

Bits 8-15: MEMWAITx.

MEMHOLDx

Bits 16-23: MEMHOLDx.

MEMHIZx

Bits 24-31: MEMHIZx.

PATT2

Attribute memory space timing register 2

Offset: 0x6c, size: 32, reset: 0xFCFCFCFC, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ATTHIZx rw								ATTHOLDx rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ATTWAITx rw								ATTSETx rw

Toggle fields

ATTSETx

Bits 0-7: ATTSETx.

ATTWAITx

Bits 8-15: ATTWAITx.

ATTHOLDx

Bits 16-23: ATTHOLDx.

ATTHIZx

Bits 24-31: ATTHIZx.

ECCR2

ECC result register 2

Offset: 0x74, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ECCx r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ECCx r

Toggle fields

ECCx

Bits 0-31: ECCx.

PCR3

PC Card/NAND Flash control register 3

Offset: 0x80, size: 32, reset: 0x00000018, access: read-write

0/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
												ECCPS rw			TAR rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TAR rw			TCLR rw						ECCEN rw	PWID rw		PTYP rw	PBKEN rw	PWAITEN rw

Toggle fields

PWAITEN

Bit 1: PWAITEN.

PBKEN

Bit 2: PBKEN.

PTYP

Bit 3: PTYP.

PWID

Bits 4-5: PWID.

ECCEN

Bit 6: ECCEN.

TCLR

Bits 9-12: TCLR.

TAR

Bits 13-16: TAR.

ECCPS

Bits 17-19: ECCPS.

SR3

FIFO status and interrupt register 3

Offset: 0x84, size: 32, reset: 0x00000040, access: Unspecified

1/7 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
									FEMPT r	IFEN rw	ILEN rw	IREN rw	IFS rw	ILS rw	IRS rw

Toggle fields

IRS

Bit 0: IRS.

ILS

Bit 1: ILS.

IFS

Bit 2: IFS.

IREN

Bit 3: IREN.

ILEN

Bit 4: ILEN.

IFEN

Bit 5: IFEN.

FEMPT

Bit 6: FEMPT.

PMEM3

Common memory space timing register 3

Offset: 0x88, size: 32, reset: 0xFCFCFCFC, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MEMHIZx rw								MEMHOLDx rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MEMWAITx rw								MEMSETx rw

Toggle fields

MEMSETx

Bits 0-7: MEMSETx.

MEMWAITx

Bits 8-15: MEMWAITx.

MEMHOLDx

Bits 16-23: MEMHOLDx.

MEMHIZx

Bits 24-31: MEMHIZx.

PATT3

Attribute memory space timing register 3

Offset: 0x8c, size: 32, reset: 0xFCFCFCFC, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ATTHIZx rw								ATTHOLDx rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ATTWAITx rw								ATTSETx rw

Toggle fields

ATTSETx

Bits 0-7: ATTSETx.

ATTWAITx

Bits 8-15: ATTWAITx.

ATTHOLDx

Bits 16-23: ATTHOLDx.

ATTHIZx

Bits 24-31: ATTHIZx.

ECCR3

ECC result register 3

Offset: 0x94, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ECCx r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ECCx r

Toggle fields

ECCx

Bits 0-31: ECCx.

PCR4

PC Card/NAND Flash control register 4

Offset: 0xa0, size: 32, reset: 0x00000018, access: read-write

0/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
												ECCPS rw			TAR rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TAR rw			TCLR rw						ECCEN rw	PWID rw		PTYP rw	PBKEN rw	PWAITEN rw

Toggle fields

PWAITEN

Bit 1: PWAITEN.

PBKEN

Bit 2: PBKEN.

PTYP

Bit 3: PTYP.

PWID

Bits 4-5: PWID.

ECCEN

Bit 6: ECCEN.

TCLR

Bits 9-12: TCLR.

TAR

Bits 13-16: TAR.

ECCPS

Bits 17-19: ECCPS.

SR4

FIFO status and interrupt register 4

Offset: 0xa4, size: 32, reset: 0x00000040, access: Unspecified

1/7 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
									FEMPT r	IFEN rw	ILEN rw	IREN rw	IFS rw	ILS rw	IRS rw

Toggle fields

IRS

Bit 0: IRS.

ILS

Bit 1: ILS.

IFS

Bit 2: IFS.

IREN

Bit 3: IREN.

ILEN

Bit 4: ILEN.

IFEN

Bit 5: IFEN.

FEMPT

Bit 6: FEMPT.

PMEM4

Common memory space timing register 4

Offset: 0xa8, size: 32, reset: 0xFCFCFCFC, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MEMHIZx rw								MEMHOLDx rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MEMWAITx rw								MEMSETx rw

Toggle fields

MEMSETx

Bits 0-7: MEMSETx.

MEMWAITx

Bits 8-15: MEMWAITx.

MEMHOLDx

Bits 16-23: MEMHOLDx.

MEMHIZx

Bits 24-31: MEMHIZx.

PATT4

Attribute memory space timing register 4

Offset: 0xac, size: 32, reset: 0xFCFCFCFC, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ATTHIZx rw								ATTHOLDx rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ATTWAITx rw								ATTSETx rw

Toggle fields

ATTSETx

Bits 0-7: ATTSETx.

ATTWAITx

Bits 8-15: ATTWAITx.

ATTHOLDx

Bits 16-23: ATTHOLDx.

ATTHIZx

Bits 24-31: ATTHIZx.

PIO4

I/O space timing register 4

Offset: 0xb0, size: 32, reset: 0xFCFCFCFC, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
IOHIZx rw								IOHOLDx rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IOWAITx rw								IOSETx rw

Toggle fields

IOSETx

Bits 0-7: IOSETx.

IOWAITx

Bits 8-15: IOWAITx.

IOHOLDx

Bits 16-23: IOHOLDx.

IOHIZx

Bits 24-31: IOHIZx.

BWTR1

SRAM/NOR-Flash write timing registers 1

Offset: 0x104, size: 32, reset: 0x0FFFFFFF, access: read-write

0/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
		ACCMOD rw		DATLAT rw				CLKDIV rw				BUSTURN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DATAST rw								ADDHLD rw				ADDSET rw

Toggle fields

ADDSET

Bits 0-3: ADDSET.

ADDHLD

Bits 4-7: ADDHLD.

DATAST

Bits 8-15: DATAST.

BUSTURN

Bits 16-19: Bus turnaround phase duration.

CLKDIV

Bits 20-23: CLKDIV.

DATLAT

Bits 24-27: DATLAT.

ACCMOD

Bits 28-29: ACCMOD.

BWTR2

SRAM/NOR-Flash write timing registers 2

Offset: 0x10c, size: 32, reset: 0x0FFFFFFF, access: read-write

0/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
		ACCMOD rw		DATLAT rw				CLKDIV rw				BUSTURN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DATAST rw								ADDHLD rw				ADDSET rw

Toggle fields

ADDSET

Bits 0-3: ADDSET.

ADDHLD

Bits 4-7: ADDHLD.

DATAST

Bits 8-15: DATAST.

BUSTURN

Bits 16-19: Bus turnaround phase duration.

CLKDIV

Bits 20-23: CLKDIV.

DATLAT

Bits 24-27: DATLAT.

ACCMOD

Bits 28-29: ACCMOD.

BWTR3

SRAM/NOR-Flash write timing registers 3

Offset: 0x114, size: 32, reset: 0x0FFFFFFF, access: read-write

0/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
		ACCMOD rw		DATLAT rw				CLKDIV rw				BUSTURN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DATAST rw								ADDHLD rw				ADDSET rw

Toggle fields

ADDSET

Bits 0-3: ADDSET.

ADDHLD

Bits 4-7: ADDHLD.

DATAST

Bits 8-15: DATAST.

BUSTURN

Bits 16-19: Bus turnaround phase duration.

CLKDIV

Bits 20-23: CLKDIV.

DATLAT

Bits 24-27: DATLAT.

ACCMOD

Bits 28-29: ACCMOD.

BWTR4

SRAM/NOR-Flash write timing registers 4

Offset: 0x11c, size: 32, reset: 0x0FFFFFFF, access: read-write

0/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
		ACCMOD rw		DATLAT rw				CLKDIV rw				BUSTURN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DATAST rw								ADDHLD rw				ADDSET rw

Toggle fields

ADDSET

Bits 0-3: ADDSET.

ADDHLD

Bits 4-7: ADDHLD.

DATAST

Bits 8-15: DATAST.

BUSTURN

Bits 16-19: Bus turnaround phase duration.

CLKDIV

Bits 20-23: CLKDIV.

DATLAT

Bits 24-27: DATLAT.

ACCMOD

Bits 28-29: ACCMOD.

FPU

0xe000ef34: Floting point unit

0/24 fields covered.

Toggle register map

Offset	Name	31	30	29	28	26	25	24	23	15	8	7	6	5	4	3	2	1	0
0x0	FPCCR	ASPEN	LSPEN								MONRDY		BFRDY	MMRDY	HFRDY	THREAD		USER	LSPACT
0x4	FPCAR	ADDRESS								ADDRESS
0x8	FPSCR	N	Z	C	V	AHP	DN	FZ	RMode			IDC			IXC	UFC	OFC	DZC	IOC

Toggle registers

FPCCR

Floating-point context control register

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

0/9 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ASPEN rw	LSPEN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							MONRDY rw		BFRDY rw	MMRDY rw	HFRDY rw	THREAD rw		USER rw	LSPACT rw

Toggle fields

LSPACT

Bit 0: LSPACT.

USER

Bit 1: USER.

THREAD

Bit 3: THREAD.

HFRDY

Bit 4: HFRDY.

MMRDY

Bit 5: MMRDY.

BFRDY

Bit 6: BFRDY.

MONRDY

Bit 8: MONRDY.

LSPEN

Bit 30: LSPEN.

ASPEN

Bit 31: ASPEN.

FPCAR

Floating-point context address register

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ADDRESS rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ADDRESS rw

Toggle fields

ADDRESS

Bits 3-31: Location of unpopulated floating-point.

FPSCR

Floating-point status control register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

0/14 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
N rw	Z rw	C rw	V rw		AHP rw	DN rw	FZ rw	RMode rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								IDC rw			IXC rw	UFC rw	OFC rw	DZC rw	IOC rw

Toggle fields

IOC

Bit 0: Invalid operation cumulative exception bit.

DZC

Bit 1: Division by zero cumulative exception bit..

OFC

Bit 2: Overflow cumulative exception bit.

UFC

Bit 3: Underflow cumulative exception bit.

IXC

Bit 4: Inexact cumulative exception bit.

IDC

Bit 7: Input denormal cumulative exception bit..

RMode

Bits 22-23: Rounding Mode control field.

FZ

Bit 24: Flush-to-zero mode control bit:.

DN

Bit 25: Default NaN mode control bit.

AHP

Bit 26: Alternative half-precision control bit.

V

Bit 28: Overflow condition code flag.

C

Bit 29: Carry condition code flag.

Z

Bit 30: Zero condition code flag.

N

Bit 31: Negative condition code flag.

FPU_CPACR

0xe000ed88: Floating point unit CPACR

0/1 fields covered.

Toggle register map

Offset	Name	31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	CPACR									CP

Toggle registers

CPACR

Coprocessor access control register

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								CP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0

Toggle fields

CP

Bits 20-23: CP.

GPIOA

0x48000000: General-purpose I/Os

177/177 fields covered.

Toggle register map

Offset	Name	31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	MODER	MODER[15]		MODER[14]		MODER[13]		MODER[12]		MODER[11]		MODER[10]		MODER[9]		MODER[8]		MODER[7]		MODER[6]		MODER[5]		MODER[4]		MODER[3]		MODER[2]		MODER[1]		MODER[0]
0x4	OTYPER																	OT[15]	OT[14]	OT[13]	OT[12]	OT[11]	OT[10]	OT[9]	OT[8]	OT[7]	OT[6]	OT[5]	OT[4]	OT[3]	OT[2]	OT[1]	OT[0]
0x8	OSPEEDR	OSPEEDR[15]		OSPEEDR[14]		OSPEEDR[13]		OSPEEDR[12]		OSPEEDR[11]		OSPEEDR[10]		OSPEEDR[9]		OSPEEDR[8]		OSPEEDR[7]		OSPEEDR[6]		OSPEEDR[5]		OSPEEDR[4]		OSPEEDR[3]		OSPEEDR[2]		OSPEEDR[1]		OSPEEDR[0]
0xc	PUPDR	PUPDR[15]		PUPDR[14]		PUPDR[13]		PUPDR[12]		PUPDR[11]		PUPDR[10]		PUPDR[9]		PUPDR[8]		PUPDR[7]		PUPDR[6]		PUPDR[5]		PUPDR[4]		PUPDR[3]		PUPDR[2]		PUPDR[1]		PUPDR[0]
0x10	IDR																	IDR[15]	IDR[14]	IDR[13]	IDR[12]	IDR[11]	IDR[10]	IDR[9]	IDR[8]	IDR[7]	IDR[6]	IDR[5]	IDR[4]	IDR[3]	IDR[2]	IDR[1]	IDR[0]
0x14	ODR																	ODR[15]	ODR[14]	ODR[13]	ODR[12]	ODR[11]	ODR[10]	ODR[9]	ODR[8]	ODR[7]	ODR[6]	ODR[5]	ODR[4]	ODR[3]	ODR[2]	ODR[1]	ODR[0]
0x18	BSRR	BR[15]	BR[14]	BR[13]	BR[12]	BR[11]	BR[10]	BR[9]	BR[8]	BR[7]	BR[6]	BR[5]	BR[4]	BR[3]	BR[2]	BR[1]	BR[0]	BS[15]	BS[14]	BS[13]	BS[12]	BS[11]	BS[10]	BS[9]	BS[8]	BS[7]	BS[6]	BS[5]	BS[4]	BS[3]	BS[2]	BS[1]	BS[0]
0x1c	LCKR																LCKK	LCK[15]	LCK[14]	LCK[13]	LCK[12]	LCK[11]	LCK[10]	LCK[9]	LCK[8]	LCK[7]	LCK[6]	LCK[5]	LCK[4]	LCK[3]	LCK[2]	LCK[1]	LCK[0]
0x20	AFRL	AFR[L7]				AFR[L6]				AFR[L5]				AFR[L4]				AFR[L3]				AFR[L2]				AFR[L1]				AFR[L0]
0x24	AFRH	AFR[H15]				AFR[H14]				AFR[H13]				AFR[H12]				AFR[H11]				AFR[H10]				AFR[H9]				AFR[H8]
0x28	BRR																	BR[15]	BR[14]	BR[13]	BR[12]	BR[11]	BR[10]	BR[9]	BR[8]	BR[7]	BR[6]	BR[5]	BR[4]	BR[3]	BR[2]	BR[1]	BR[0]

Toggle registers

MODER

GPIO port mode register

Offset: 0x0, size: 32, reset: 0xA8000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MODER[15] rw		MODER[14] rw		MODER[13] rw		MODER[12] rw		MODER[11] rw		MODER[10] rw		MODER[9] rw		MODER[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MODER[7] rw		MODER[6] rw		MODER[5] rw		MODER[4] rw		MODER[3] rw		MODER[2] rw		MODER[1] rw		MODER[0] rw

Toggle fields

MODER[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

OTYPER

GPIO port output type register

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OT[15] rw	OT[14] rw	OT[13] rw	OT[12] rw	OT[11] rw	OT[10] rw	OT[9] rw	OT[8] rw	OT[7] rw	OT[6] rw	OT[5] rw	OT[4] rw	OT[3] rw	OT[2] rw	OT[1] rw	OT[0] rw

Toggle fields

OT[0]

Bit 0: Port x configuration pin 0.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[1]

Bit 1: Port x configuration pin 1.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[2]

Bit 2: Port x configuration pin 2.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[3]

Bit 3: Port x configuration pin 3.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[4]

Bit 4: Port x configuration pin 4.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[5]

Bit 5: Port x configuration pin 5.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[6]

Bit 6: Port x configuration pin 6.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[7]

Bit 7: Port x configuration pin 7.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[8]

Bit 8: Port x configuration pin 8.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[9]

Bit 9: Port x configuration pin 9.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[10]

Bit 10: Port x configuration pin 10.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[11]

Bit 11: Port x configuration pin 11.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[12]

Bit 12: Port x configuration pin 12.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[13]

Bit 13: Port x configuration pin 13.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[14]

Bit 14: Port x configuration pin 14.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[15]

Bit 15: Port x configuration pin 15.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OSPEEDR

GPIO port output speed register

Offset: 0x8, size: 32, reset: 0x0C000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OSPEEDR[15] rw		OSPEEDR[14] rw		OSPEEDR[13] rw		OSPEEDR[12] rw		OSPEEDR[11] rw		OSPEEDR[10] rw		OSPEEDR[9] rw		OSPEEDR[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OSPEEDR[7] rw		OSPEEDR[6] rw		OSPEEDR[5] rw		OSPEEDR[4] rw		OSPEEDR[3] rw		OSPEEDR[2] rw		OSPEEDR[1] rw		OSPEEDR[0] rw

Toggle fields

OSPEEDR[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

PUPDR

GPIO port pull-up/pull-down register

Offset: 0xc, size: 32, reset: 0x64000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PUPDR[15] rw		PUPDR[14] rw		PUPDR[13] rw		PUPDR[12] rw		PUPDR[11] rw		PUPDR[10] rw		PUPDR[9] rw		PUPDR[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PUPDR[7] rw		PUPDR[6] rw		PUPDR[5] rw		PUPDR[4] rw		PUPDR[3] rw		PUPDR[2] rw		PUPDR[1] rw		PUPDR[0] rw

Toggle fields

PUPDR[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

IDR

GPIO port input data register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-only

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IDR[15] r	IDR[14] r	IDR[13] r	IDR[12] r	IDR[11] r	IDR[10] r	IDR[9] r	IDR[8] r	IDR[7] r	IDR[6] r	IDR[5] r	IDR[4] r	IDR[3] r	IDR[2] r	IDR[1] r	IDR[0] r

Toggle fields

IDR[0]

Bit 0: Port input data pin 0.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[1]

Bit 1: Port input data pin 1.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[2]

Bit 2: Port input data pin 2.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[3]

Bit 3: Port input data pin 3.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[4]

Bit 4: Port input data pin 4.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[5]

Bit 5: Port input data pin 5.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[6]

Bit 6: Port input data pin 6.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[7]

Bit 7: Port input data pin 7.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[8]

Bit 8: Port input data pin 8.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[9]

Bit 9: Port input data pin 9.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[10]

Bit 10: Port input data pin 10.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[11]

Bit 11: Port input data pin 11.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[12]

Bit 12: Port input data pin 12.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[13]

Bit 13: Port input data pin 13.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[14]

Bit 14: Port input data pin 14.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[15]

Bit 15: Port input data pin 15.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

ODR

GPIO port output data register

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ODR[15] rw	ODR[14] rw	ODR[13] rw	ODR[12] rw	ODR[11] rw	ODR[10] rw	ODR[9] rw	ODR[8] rw	ODR[7] rw	ODR[6] rw	ODR[5] rw	ODR[4] rw	ODR[3] rw	ODR[2] rw	ODR[1] rw	ODR[0] rw

Toggle fields

ODR[0]

Bit 0: Port output data pin 0.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[1]

Bit 1: Port output data pin 1.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[2]

Bit 2: Port output data pin 2.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[3]

Bit 3: Port output data pin 3.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[4]

Bit 4: Port output data pin 4.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[5]

Bit 5: Port output data pin 5.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[6]

Bit 6: Port output data pin 6.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[7]

Bit 7: Port output data pin 7.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[8]

Bit 8: Port output data pin 8.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[9]

Bit 9: Port output data pin 9.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[10]

Bit 10: Port output data pin 10.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[11]

Bit 11: Port output data pin 11.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[12]

Bit 12: Port output data pin 12.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[13]

Bit 13: Port output data pin 13.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[14]

Bit 14: Port output data pin 14.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[15]

Bit 15: Port output data pin 15.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

BSRR

GPIO port bit set/reset register

Offset: 0x18, size: 32, reset: 0x00000000, access: write-only

32/32 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BR[15] w	BR[14] w	BR[13] w	BR[12] w	BR[11] w	BR[10] w	BR[9] w	BR[8] w	BR[7] w	BR[6] w	BR[5] w	BR[4] w	BR[3] w	BR[2] w	BR[1] w	BR[0] w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BS[15] w	BS[14] w	BS[13] w	BS[12] w	BS[11] w	BS[10] w	BS[9] w	BS[8] w	BS[7] w	BS[6] w	BS[5] w	BS[4] w	BS[3] w	BS[2] w	BS[1] w	BS[0] w

Toggle fields

BS[0]

Bit 0: Port x set pin 0.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[1]

Bit 1: Port x set pin 1.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[2]

Bit 2: Port x set pin 2.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[3]

Bit 3: Port x set pin 3.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[4]

Bit 4: Port x set pin 4.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[5]

Bit 5: Port x set pin 5.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[6]

Bit 6: Port x set pin 6.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[7]

Bit 7: Port x set pin 7.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[8]

Bit 8: Port x set pin 8.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[9]

Bit 9: Port x set pin 9.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[10]

Bit 10: Port x set pin 10.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[11]

Bit 11: Port x set pin 11.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[12]

Bit 12: Port x set pin 12.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[13]

Bit 13: Port x set pin 13.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[14]

Bit 14: Port x set pin 14.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[15]

Bit 15: Port x set pin 15.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BR[0]

Bit 16: Port x reset pin 0.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[1]

Bit 17: Port x reset pin 1.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[2]

Bit 18: Port x reset pin 2.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[3]

Bit 19: Port x reset pin 3.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[4]

Bit 20: Port x reset pin 4.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[5]

Bit 21: Port x reset pin 5.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[6]

Bit 22: Port x reset pin 6.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[7]

Bit 23: Port x reset pin 7.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[8]

Bit 24: Port x reset pin 8.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[9]

Bit 25: Port x reset pin 9.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[10]

Bit 26: Port x reset pin 10.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[11]

Bit 27: Port x reset pin 11.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[12]

Bit 28: Port x reset pin 12.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[13]

Bit 29: Port x reset pin 13.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[14]

Bit 30: Port x reset pin 14.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[15]

Bit 31: Port x reset pin 15.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

LCKR

GPIO port configuration lock register

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

17/17 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															LCKK rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
LCK[15] rw	LCK[14] rw	LCK[13] rw	LCK[12] rw	LCK[11] rw	LCK[10] rw	LCK[9] rw	LCK[8] rw	LCK[7] rw	LCK[6] rw	LCK[5] rw	LCK[4] rw	LCK[3] rw	LCK[2] rw	LCK[1] rw	LCK[0] rw

Toggle fields

LCK[0]

Bit 0: Port x lock pin 0.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[1]

Bit 1: Port x lock pin 1.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[2]

Bit 2: Port x lock pin 2.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[3]

Bit 3: Port x lock pin 3.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[4]

Bit 4: Port x lock pin 4.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[5]

Bit 5: Port x lock pin 5.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[6]

Bit 6: Port x lock pin 6.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[7]

Bit 7: Port x lock pin 7.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[8]

Bit 8: Port x lock pin 8.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[9]

Bit 9: Port x lock pin 9.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[10]

Bit 10: Port x lock pin 10.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[11]

Bit 11: Port x lock pin 11.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[12]

Bit 12: Port x lock pin 12.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[13]

Bit 13: Port x lock pin 13.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[14]

Bit 14: Port x lock pin 14.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[15]

Bit 15: Port x lock pin 15.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCKK

Bit 16: Lok Key.

Allowed values:
0: NotActive: Port configuration lock key not active
1: Active: Port configuration lock key active

AFRL

GPIO alternate function low register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AFR[L7] rw				AFR[L6] rw				AFR[L5] rw				AFR[L4] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AFR[L3] rw				AFR[L2] rw				AFR[L1] rw				AFR[L0] rw

Toggle fields

AFR[L0]

Bits 0-3: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L1]

Bits 4-7: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L2]

Bits 8-11: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L3]

Bits 12-15: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L4]

Bits 16-19: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L5]

Bits 20-23: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L6]

Bits 24-27: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L7]

Bits 28-31: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH

GPIO alternate function high register

Offset: 0x24, size: 32, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AFR[H15] rw				AFR[H14] rw				AFR[H13] rw				AFR[H12] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AFR[H11] rw				AFR[H10] rw				AFR[H9] rw				AFR[H8] rw

Toggle fields

AFR[H8]

Bits 0-3: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H9]

Bits 4-7: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H10]

Bits 8-11: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H11]

Bits 12-15: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H12]

Bits 16-19: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H13]

Bits 20-23: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H14]

Bits 24-27: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H15]

Bits 28-31: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

BRR

Port bit reset register

Offset: 0x28, size: 32, reset: 0x00000000, access: write-only

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BR[15] w	BR[14] w	BR[13] w	BR[12] w	BR[11] w	BR[10] w	BR[9] w	BR[8] w	BR[7] w	BR[6] w	BR[5] w	BR[4] w	BR[3] w	BR[2] w	BR[1] w	BR[0] w

Toggle fields

BR[0]

Bit 0: Port x reset pin 0.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[1]

Bit 1: Port x reset pin 1.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[2]

Bit 2: Port x reset pin 2.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[3]

Bit 3: Port x reset pin 3.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[4]

Bit 4: Port x reset pin 4.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[5]

Bit 5: Port x reset pin 5.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[6]

Bit 6: Port x reset pin 6.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[7]

Bit 7: Port x reset pin 7.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[8]

Bit 8: Port x reset pin 8.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[9]

Bit 9: Port x reset pin 9.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[10]

Bit 10: Port x reset pin 10.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[11]

Bit 11: Port x reset pin 11.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[12]

Bit 12: Port x reset pin 12.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[13]

Bit 13: Port x reset pin 13.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[14]

Bit 14: Port x reset pin 14.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[15]

Bit 15: Port x reset pin 15.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

GPIOB

0x48000400: General-purpose I/Os

177/177 fields covered.

Toggle register map

Offset	Name	31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	MODER	MODER[15]		MODER[14]		MODER[13]		MODER[12]		MODER[11]		MODER[10]		MODER[9]		MODER[8]		MODER[7]		MODER[6]		MODER[5]		MODER[4]		MODER[3]		MODER[2]		MODER[1]		MODER[0]
0x4	OTYPER																	OT[15]	OT[14]	OT[13]	OT[12]	OT[11]	OT[10]	OT[9]	OT[8]	OT[7]	OT[6]	OT[5]	OT[4]	OT[3]	OT[2]	OT[1]	OT[0]
0x8	OSPEEDR	OSPEEDR[15]		OSPEEDR[14]		OSPEEDR[13]		OSPEEDR[12]		OSPEEDR[11]		OSPEEDR[10]		OSPEEDR[9]		OSPEEDR[8]		OSPEEDR[7]		OSPEEDR[6]		OSPEEDR[5]		OSPEEDR[4]		OSPEEDR[3]		OSPEEDR[2]		OSPEEDR[1]		OSPEEDR[0]
0xc	PUPDR	PUPDR[15]		PUPDR[14]		PUPDR[13]		PUPDR[12]		PUPDR[11]		PUPDR[10]		PUPDR[9]		PUPDR[8]		PUPDR[7]		PUPDR[6]		PUPDR[5]		PUPDR[4]		PUPDR[3]		PUPDR[2]		PUPDR[1]		PUPDR[0]
0x10	IDR																	IDR[15]	IDR[14]	IDR[13]	IDR[12]	IDR[11]	IDR[10]	IDR[9]	IDR[8]	IDR[7]	IDR[6]	IDR[5]	IDR[4]	IDR[3]	IDR[2]	IDR[1]	IDR[0]
0x14	ODR																	ODR[15]	ODR[14]	ODR[13]	ODR[12]	ODR[11]	ODR[10]	ODR[9]	ODR[8]	ODR[7]	ODR[6]	ODR[5]	ODR[4]	ODR[3]	ODR[2]	ODR[1]	ODR[0]
0x18	BSRR	BR[15]	BR[14]	BR[13]	BR[12]	BR[11]	BR[10]	BR[9]	BR[8]	BR[7]	BR[6]	BR[5]	BR[4]	BR[3]	BR[2]	BR[1]	BR[0]	BS[15]	BS[14]	BS[13]	BS[12]	BS[11]	BS[10]	BS[9]	BS[8]	BS[7]	BS[6]	BS[5]	BS[4]	BS[3]	BS[2]	BS[1]	BS[0]
0x1c	LCKR																LCKK	LCK[15]	LCK[14]	LCK[13]	LCK[12]	LCK[11]	LCK[10]	LCK[9]	LCK[8]	LCK[7]	LCK[6]	LCK[5]	LCK[4]	LCK[3]	LCK[2]	LCK[1]	LCK[0]
0x20	AFRL	AFR[L7]				AFR[L6]				AFR[L5]				AFR[L4]				AFR[L3]				AFR[L2]				AFR[L1]				AFR[L0]
0x24	AFRH	AFR[H15]				AFR[H14]				AFR[H13]				AFR[H12]				AFR[H11]				AFR[H10]				AFR[H9]				AFR[H8]
0x28	BRR																	BR[15]	BR[14]	BR[13]	BR[12]	BR[11]	BR[10]	BR[9]	BR[8]	BR[7]	BR[6]	BR[5]	BR[4]	BR[3]	BR[2]	BR[1]	BR[0]

Toggle registers

MODER

GPIO port mode register

Offset: 0x0, size: 32, reset: 0x00000280, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MODER[15] rw		MODER[14] rw		MODER[13] rw		MODER[12] rw		MODER[11] rw		MODER[10] rw		MODER[9] rw		MODER[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MODER[7] rw		MODER[6] rw		MODER[5] rw		MODER[4] rw		MODER[3] rw		MODER[2] rw		MODER[1] rw		MODER[0] rw

Toggle fields

MODER[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

OTYPER

GPIO port output type register

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OT[15] rw	OT[14] rw	OT[13] rw	OT[12] rw	OT[11] rw	OT[10] rw	OT[9] rw	OT[8] rw	OT[7] rw	OT[6] rw	OT[5] rw	OT[4] rw	OT[3] rw	OT[2] rw	OT[1] rw	OT[0] rw

Toggle fields

OT[0]

Bit 0: Port x configuration pin 0.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[1]

Bit 1: Port x configuration pin 1.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[2]

Bit 2: Port x configuration pin 2.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[3]

Bit 3: Port x configuration pin 3.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[4]

Bit 4: Port x configuration pin 4.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[5]

Bit 5: Port x configuration pin 5.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[6]

Bit 6: Port x configuration pin 6.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[7]

Bit 7: Port x configuration pin 7.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[8]

Bit 8: Port x configuration pin 8.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[9]

Bit 9: Port x configuration pin 9.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[10]

Bit 10: Port x configuration pin 10.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[11]

Bit 11: Port x configuration pin 11.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[12]

Bit 12: Port x configuration pin 12.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[13]

Bit 13: Port x configuration pin 13.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[14]

Bit 14: Port x configuration pin 14.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[15]

Bit 15: Port x configuration pin 15.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OSPEEDR

GPIO port output speed register

Offset: 0x8, size: 32, reset: 0x000000C0, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OSPEEDR[15] rw		OSPEEDR[14] rw		OSPEEDR[13] rw		OSPEEDR[12] rw		OSPEEDR[11] rw		OSPEEDR[10] rw		OSPEEDR[9] rw		OSPEEDR[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OSPEEDR[7] rw		OSPEEDR[6] rw		OSPEEDR[5] rw		OSPEEDR[4] rw		OSPEEDR[3] rw		OSPEEDR[2] rw		OSPEEDR[1] rw		OSPEEDR[0] rw

Toggle fields

OSPEEDR[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

PUPDR

GPIO port pull-up/pull-down register

Offset: 0xc, size: 32, reset: 0x00000100, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PUPDR[15] rw		PUPDR[14] rw		PUPDR[13] rw		PUPDR[12] rw		PUPDR[11] rw		PUPDR[10] rw		PUPDR[9] rw		PUPDR[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PUPDR[7] rw		PUPDR[6] rw		PUPDR[5] rw		PUPDR[4] rw		PUPDR[3] rw		PUPDR[2] rw		PUPDR[1] rw		PUPDR[0] rw

Toggle fields

PUPDR[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

IDR

GPIO port input data register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-only

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IDR[15] r	IDR[14] r	IDR[13] r	IDR[12] r	IDR[11] r	IDR[10] r	IDR[9] r	IDR[8] r	IDR[7] r	IDR[6] r	IDR[5] r	IDR[4] r	IDR[3] r	IDR[2] r	IDR[1] r	IDR[0] r

Toggle fields

IDR[0]

Bit 0: Port input data pin 0.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[1]

Bit 1: Port input data pin 1.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[2]

Bit 2: Port input data pin 2.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[3]

Bit 3: Port input data pin 3.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[4]

Bit 4: Port input data pin 4.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[5]

Bit 5: Port input data pin 5.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[6]

Bit 6: Port input data pin 6.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[7]

Bit 7: Port input data pin 7.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[8]

Bit 8: Port input data pin 8.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[9]

Bit 9: Port input data pin 9.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[10]

Bit 10: Port input data pin 10.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[11]

Bit 11: Port input data pin 11.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[12]

Bit 12: Port input data pin 12.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[13]

Bit 13: Port input data pin 13.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[14]

Bit 14: Port input data pin 14.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[15]

Bit 15: Port input data pin 15.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

ODR

GPIO port output data register

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ODR[15] rw	ODR[14] rw	ODR[13] rw	ODR[12] rw	ODR[11] rw	ODR[10] rw	ODR[9] rw	ODR[8] rw	ODR[7] rw	ODR[6] rw	ODR[5] rw	ODR[4] rw	ODR[3] rw	ODR[2] rw	ODR[1] rw	ODR[0] rw

Toggle fields

ODR[0]

Bit 0: Port output data pin 0.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[1]

Bit 1: Port output data pin 1.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[2]

Bit 2: Port output data pin 2.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[3]

Bit 3: Port output data pin 3.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[4]

Bit 4: Port output data pin 4.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[5]

Bit 5: Port output data pin 5.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[6]

Bit 6: Port output data pin 6.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[7]

Bit 7: Port output data pin 7.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[8]

Bit 8: Port output data pin 8.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[9]

Bit 9: Port output data pin 9.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[10]

Bit 10: Port output data pin 10.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[11]

Bit 11: Port output data pin 11.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[12]

Bit 12: Port output data pin 12.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[13]

Bit 13: Port output data pin 13.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[14]

Bit 14: Port output data pin 14.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[15]

Bit 15: Port output data pin 15.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

BSRR

GPIO port bit set/reset register

Offset: 0x18, size: 32, reset: 0x00000000, access: write-only

32/32 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BR[15] w	BR[14] w	BR[13] w	BR[12] w	BR[11] w	BR[10] w	BR[9] w	BR[8] w	BR[7] w	BR[6] w	BR[5] w	BR[4] w	BR[3] w	BR[2] w	BR[1] w	BR[0] w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BS[15] w	BS[14] w	BS[13] w	BS[12] w	BS[11] w	BS[10] w	BS[9] w	BS[8] w	BS[7] w	BS[6] w	BS[5] w	BS[4] w	BS[3] w	BS[2] w	BS[1] w	BS[0] w

Toggle fields

BS[0]

Bit 0: Port x set pin 0.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[1]

Bit 1: Port x set pin 1.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[2]

Bit 2: Port x set pin 2.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[3]

Bit 3: Port x set pin 3.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[4]

Bit 4: Port x set pin 4.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[5]

Bit 5: Port x set pin 5.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[6]

Bit 6: Port x set pin 6.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[7]

Bit 7: Port x set pin 7.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[8]

Bit 8: Port x set pin 8.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[9]

Bit 9: Port x set pin 9.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[10]

Bit 10: Port x set pin 10.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[11]

Bit 11: Port x set pin 11.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[12]

Bit 12: Port x set pin 12.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[13]

Bit 13: Port x set pin 13.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[14]

Bit 14: Port x set pin 14.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[15]

Bit 15: Port x set pin 15.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BR[0]

Bit 16: Port x reset pin 0.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[1]

Bit 17: Port x reset pin 1.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[2]

Bit 18: Port x reset pin 2.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[3]

Bit 19: Port x reset pin 3.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[4]

Bit 20: Port x reset pin 4.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[5]

Bit 21: Port x reset pin 5.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[6]

Bit 22: Port x reset pin 6.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[7]

Bit 23: Port x reset pin 7.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[8]

Bit 24: Port x reset pin 8.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[9]

Bit 25: Port x reset pin 9.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[10]

Bit 26: Port x reset pin 10.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[11]

Bit 27: Port x reset pin 11.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[12]

Bit 28: Port x reset pin 12.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[13]

Bit 29: Port x reset pin 13.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[14]

Bit 30: Port x reset pin 14.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[15]

Bit 31: Port x reset pin 15.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

LCKR

GPIO port configuration lock register

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

17/17 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															LCKK rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
LCK[15] rw	LCK[14] rw	LCK[13] rw	LCK[12] rw	LCK[11] rw	LCK[10] rw	LCK[9] rw	LCK[8] rw	LCK[7] rw	LCK[6] rw	LCK[5] rw	LCK[4] rw	LCK[3] rw	LCK[2] rw	LCK[1] rw	LCK[0] rw

Toggle fields

LCK[0]

Bit 0: Port x lock pin 0.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[1]

Bit 1: Port x lock pin 1.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[2]

Bit 2: Port x lock pin 2.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[3]

Bit 3: Port x lock pin 3.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[4]

Bit 4: Port x lock pin 4.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[5]

Bit 5: Port x lock pin 5.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[6]

Bit 6: Port x lock pin 6.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[7]

Bit 7: Port x lock pin 7.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[8]

Bit 8: Port x lock pin 8.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[9]

Bit 9: Port x lock pin 9.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[10]

Bit 10: Port x lock pin 10.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[11]

Bit 11: Port x lock pin 11.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[12]

Bit 12: Port x lock pin 12.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[13]

Bit 13: Port x lock pin 13.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[14]

Bit 14: Port x lock pin 14.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[15]

Bit 15: Port x lock pin 15.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCKK

Bit 16: Lok Key.

Allowed values:
0: NotActive: Port configuration lock key not active
1: Active: Port configuration lock key active

AFRL

GPIO alternate function low register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AFR[L7] rw				AFR[L6] rw				AFR[L5] rw				AFR[L4] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AFR[L3] rw				AFR[L2] rw				AFR[L1] rw				AFR[L0] rw

Toggle fields

AFR[L0]

Bits 0-3: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L1]

Bits 4-7: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L2]

Bits 8-11: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L3]

Bits 12-15: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L4]

Bits 16-19: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L5]

Bits 20-23: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L6]

Bits 24-27: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L7]

Bits 28-31: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH

GPIO alternate function high register

Offset: 0x24, size: 32, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AFR[H15] rw				AFR[H14] rw				AFR[H13] rw				AFR[H12] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AFR[H11] rw				AFR[H10] rw				AFR[H9] rw				AFR[H8] rw

Toggle fields

AFR[H8]

Bits 0-3: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H9]

Bits 4-7: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H10]

Bits 8-11: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H11]

Bits 12-15: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H12]

Bits 16-19: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H13]

Bits 20-23: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H14]

Bits 24-27: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H15]

Bits 28-31: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

BRR

Port bit reset register

Offset: 0x28, size: 32, reset: 0x00000000, access: write-only

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BR[15] w	BR[14] w	BR[13] w	BR[12] w	BR[11] w	BR[10] w	BR[9] w	BR[8] w	BR[7] w	BR[6] w	BR[5] w	BR[4] w	BR[3] w	BR[2] w	BR[1] w	BR[0] w

Toggle fields

BR[0]

Bit 0: Port x reset pin 0.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[1]

Bit 1: Port x reset pin 1.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[2]

Bit 2: Port x reset pin 2.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[3]

Bit 3: Port x reset pin 3.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[4]

Bit 4: Port x reset pin 4.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[5]

Bit 5: Port x reset pin 5.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[6]

Bit 6: Port x reset pin 6.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[7]

Bit 7: Port x reset pin 7.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[8]

Bit 8: Port x reset pin 8.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[9]

Bit 9: Port x reset pin 9.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[10]

Bit 10: Port x reset pin 10.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[11]

Bit 11: Port x reset pin 11.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[12]

Bit 12: Port x reset pin 12.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[13]

Bit 13: Port x reset pin 13.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[14]

Bit 14: Port x reset pin 14.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[15]

Bit 15: Port x reset pin 15.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

GPIOC

0x48000800: General-purpose I/Os

177/177 fields covered.

Toggle register map

Offset	Name	31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	MODER	MODER[15]		MODER[14]		MODER[13]		MODER[12]		MODER[11]		MODER[10]		MODER[9]		MODER[8]		MODER[7]		MODER[6]		MODER[5]		MODER[4]		MODER[3]		MODER[2]		MODER[1]		MODER[0]
0x4	OTYPER																	OT[15]	OT[14]	OT[13]	OT[12]	OT[11]	OT[10]	OT[9]	OT[8]	OT[7]	OT[6]	OT[5]	OT[4]	OT[3]	OT[2]	OT[1]	OT[0]
0x8	OSPEEDR	OSPEEDR[15]		OSPEEDR[14]		OSPEEDR[13]		OSPEEDR[12]		OSPEEDR[11]		OSPEEDR[10]		OSPEEDR[9]		OSPEEDR[8]		OSPEEDR[7]		OSPEEDR[6]		OSPEEDR[5]		OSPEEDR[4]		OSPEEDR[3]		OSPEEDR[2]		OSPEEDR[1]		OSPEEDR[0]
0xc	PUPDR	PUPDR[15]		PUPDR[14]		PUPDR[13]		PUPDR[12]		PUPDR[11]		PUPDR[10]		PUPDR[9]		PUPDR[8]		PUPDR[7]		PUPDR[6]		PUPDR[5]		PUPDR[4]		PUPDR[3]		PUPDR[2]		PUPDR[1]		PUPDR[0]
0x10	IDR																	IDR[15]	IDR[14]	IDR[13]	IDR[12]	IDR[11]	IDR[10]	IDR[9]	IDR[8]	IDR[7]	IDR[6]	IDR[5]	IDR[4]	IDR[3]	IDR[2]	IDR[1]	IDR[0]
0x14	ODR																	ODR[15]	ODR[14]	ODR[13]	ODR[12]	ODR[11]	ODR[10]	ODR[9]	ODR[8]	ODR[7]	ODR[6]	ODR[5]	ODR[4]	ODR[3]	ODR[2]	ODR[1]	ODR[0]
0x18	BSRR	BR[15]	BR[14]	BR[13]	BR[12]	BR[11]	BR[10]	BR[9]	BR[8]	BR[7]	BR[6]	BR[5]	BR[4]	BR[3]	BR[2]	BR[1]	BR[0]	BS[15]	BS[14]	BS[13]	BS[12]	BS[11]	BS[10]	BS[9]	BS[8]	BS[7]	BS[6]	BS[5]	BS[4]	BS[3]	BS[2]	BS[1]	BS[0]
0x1c	LCKR																LCKK	LCK[15]	LCK[14]	LCK[13]	LCK[12]	LCK[11]	LCK[10]	LCK[9]	LCK[8]	LCK[7]	LCK[6]	LCK[5]	LCK[4]	LCK[3]	LCK[2]	LCK[1]	LCK[0]
0x20	AFRL	AFR[L7]				AFR[L6]				AFR[L5]				AFR[L4]				AFR[L3]				AFR[L2]				AFR[L1]				AFR[L0]
0x24	AFRH	AFR[H15]				AFR[H14]				AFR[H13]				AFR[H12]				AFR[H11]				AFR[H10]				AFR[H9]				AFR[H8]
0x28	BRR																	BR[15]	BR[14]	BR[13]	BR[12]	BR[11]	BR[10]	BR[9]	BR[8]	BR[7]	BR[6]	BR[5]	BR[4]	BR[3]	BR[2]	BR[1]	BR[0]

Toggle registers

MODER

GPIO port mode register

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MODER[15] rw		MODER[14] rw		MODER[13] rw		MODER[12] rw		MODER[11] rw		MODER[10] rw		MODER[9] rw		MODER[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MODER[7] rw		MODER[6] rw		MODER[5] rw		MODER[4] rw		MODER[3] rw		MODER[2] rw		MODER[1] rw		MODER[0] rw

Toggle fields

MODER[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

OTYPER

GPIO port output type register

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OT[15] rw	OT[14] rw	OT[13] rw	OT[12] rw	OT[11] rw	OT[10] rw	OT[9] rw	OT[8] rw	OT[7] rw	OT[6] rw	OT[5] rw	OT[4] rw	OT[3] rw	OT[2] rw	OT[1] rw	OT[0] rw

Toggle fields

OT[0]

Bit 0: Port x configuration pin 0.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[1]

Bit 1: Port x configuration pin 1.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[2]

Bit 2: Port x configuration pin 2.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[3]

Bit 3: Port x configuration pin 3.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[4]

Bit 4: Port x configuration pin 4.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[5]

Bit 5: Port x configuration pin 5.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[6]

Bit 6: Port x configuration pin 6.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[7]

Bit 7: Port x configuration pin 7.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[8]

Bit 8: Port x configuration pin 8.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[9]

Bit 9: Port x configuration pin 9.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[10]

Bit 10: Port x configuration pin 10.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[11]

Bit 11: Port x configuration pin 11.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[12]

Bit 12: Port x configuration pin 12.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[13]

Bit 13: Port x configuration pin 13.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[14]

Bit 14: Port x configuration pin 14.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[15]

Bit 15: Port x configuration pin 15.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OSPEEDR

GPIO port output speed register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OSPEEDR[15] rw		OSPEEDR[14] rw		OSPEEDR[13] rw		OSPEEDR[12] rw		OSPEEDR[11] rw		OSPEEDR[10] rw		OSPEEDR[9] rw		OSPEEDR[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OSPEEDR[7] rw		OSPEEDR[6] rw		OSPEEDR[5] rw		OSPEEDR[4] rw		OSPEEDR[3] rw		OSPEEDR[2] rw		OSPEEDR[1] rw		OSPEEDR[0] rw

Toggle fields

OSPEEDR[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

PUPDR

GPIO port pull-up/pull-down register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PUPDR[15] rw		PUPDR[14] rw		PUPDR[13] rw		PUPDR[12] rw		PUPDR[11] rw		PUPDR[10] rw		PUPDR[9] rw		PUPDR[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PUPDR[7] rw		PUPDR[6] rw		PUPDR[5] rw		PUPDR[4] rw		PUPDR[3] rw		PUPDR[2] rw		PUPDR[1] rw		PUPDR[0] rw

Toggle fields

PUPDR[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

IDR

GPIO port input data register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-only

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IDR[15] r	IDR[14] r	IDR[13] r	IDR[12] r	IDR[11] r	IDR[10] r	IDR[9] r	IDR[8] r	IDR[7] r	IDR[6] r	IDR[5] r	IDR[4] r	IDR[3] r	IDR[2] r	IDR[1] r	IDR[0] r

Toggle fields

IDR[0]

Bit 0: Port input data pin 0.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[1]

Bit 1: Port input data pin 1.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[2]

Bit 2: Port input data pin 2.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[3]

Bit 3: Port input data pin 3.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[4]

Bit 4: Port input data pin 4.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[5]

Bit 5: Port input data pin 5.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[6]

Bit 6: Port input data pin 6.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[7]

Bit 7: Port input data pin 7.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[8]

Bit 8: Port input data pin 8.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[9]

Bit 9: Port input data pin 9.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[10]

Bit 10: Port input data pin 10.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[11]

Bit 11: Port input data pin 11.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[12]

Bit 12: Port input data pin 12.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[13]

Bit 13: Port input data pin 13.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[14]

Bit 14: Port input data pin 14.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[15]

Bit 15: Port input data pin 15.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

ODR

GPIO port output data register

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ODR[15] rw	ODR[14] rw	ODR[13] rw	ODR[12] rw	ODR[11] rw	ODR[10] rw	ODR[9] rw	ODR[8] rw	ODR[7] rw	ODR[6] rw	ODR[5] rw	ODR[4] rw	ODR[3] rw	ODR[2] rw	ODR[1] rw	ODR[0] rw

Toggle fields

ODR[0]

Bit 0: Port output data pin 0.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[1]

Bit 1: Port output data pin 1.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[2]

Bit 2: Port output data pin 2.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[3]

Bit 3: Port output data pin 3.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[4]

Bit 4: Port output data pin 4.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[5]

Bit 5: Port output data pin 5.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[6]

Bit 6: Port output data pin 6.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[7]

Bit 7: Port output data pin 7.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[8]

Bit 8: Port output data pin 8.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[9]

Bit 9: Port output data pin 9.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[10]

Bit 10: Port output data pin 10.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[11]

Bit 11: Port output data pin 11.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[12]

Bit 12: Port output data pin 12.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[13]

Bit 13: Port output data pin 13.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[14]

Bit 14: Port output data pin 14.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[15]

Bit 15: Port output data pin 15.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

BSRR

GPIO port bit set/reset register

Offset: 0x18, size: 32, reset: 0x00000000, access: write-only

32/32 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BR[15] w	BR[14] w	BR[13] w	BR[12] w	BR[11] w	BR[10] w	BR[9] w	BR[8] w	BR[7] w	BR[6] w	BR[5] w	BR[4] w	BR[3] w	BR[2] w	BR[1] w	BR[0] w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BS[15] w	BS[14] w	BS[13] w	BS[12] w	BS[11] w	BS[10] w	BS[9] w	BS[8] w	BS[7] w	BS[6] w	BS[5] w	BS[4] w	BS[3] w	BS[2] w	BS[1] w	BS[0] w

Toggle fields

BS[0]

Bit 0: Port x set pin 0.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[1]

Bit 1: Port x set pin 1.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[2]

Bit 2: Port x set pin 2.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[3]

Bit 3: Port x set pin 3.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[4]

Bit 4: Port x set pin 4.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[5]

Bit 5: Port x set pin 5.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[6]

Bit 6: Port x set pin 6.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[7]

Bit 7: Port x set pin 7.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[8]

Bit 8: Port x set pin 8.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[9]

Bit 9: Port x set pin 9.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[10]

Bit 10: Port x set pin 10.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[11]

Bit 11: Port x set pin 11.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[12]

Bit 12: Port x set pin 12.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[13]

Bit 13: Port x set pin 13.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[14]

Bit 14: Port x set pin 14.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[15]

Bit 15: Port x set pin 15.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BR[0]

Bit 16: Port x reset pin 0.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[1]

Bit 17: Port x reset pin 1.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[2]

Bit 18: Port x reset pin 2.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[3]

Bit 19: Port x reset pin 3.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[4]

Bit 20: Port x reset pin 4.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[5]

Bit 21: Port x reset pin 5.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[6]

Bit 22: Port x reset pin 6.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[7]

Bit 23: Port x reset pin 7.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[8]

Bit 24: Port x reset pin 8.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[9]

Bit 25: Port x reset pin 9.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[10]

Bit 26: Port x reset pin 10.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[11]

Bit 27: Port x reset pin 11.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[12]

Bit 28: Port x reset pin 12.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[13]

Bit 29: Port x reset pin 13.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[14]

Bit 30: Port x reset pin 14.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[15]

Bit 31: Port x reset pin 15.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

LCKR

GPIO port configuration lock register

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

17/17 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															LCKK rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
LCK[15] rw	LCK[14] rw	LCK[13] rw	LCK[12] rw	LCK[11] rw	LCK[10] rw	LCK[9] rw	LCK[8] rw	LCK[7] rw	LCK[6] rw	LCK[5] rw	LCK[4] rw	LCK[3] rw	LCK[2] rw	LCK[1] rw	LCK[0] rw

Toggle fields

LCK[0]

Bit 0: Port x lock pin 0.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[1]

Bit 1: Port x lock pin 1.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[2]

Bit 2: Port x lock pin 2.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[3]

Bit 3: Port x lock pin 3.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[4]

Bit 4: Port x lock pin 4.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[5]

Bit 5: Port x lock pin 5.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[6]

Bit 6: Port x lock pin 6.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[7]

Bit 7: Port x lock pin 7.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[8]

Bit 8: Port x lock pin 8.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[9]

Bit 9: Port x lock pin 9.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[10]

Bit 10: Port x lock pin 10.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[11]

Bit 11: Port x lock pin 11.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[12]

Bit 12: Port x lock pin 12.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[13]

Bit 13: Port x lock pin 13.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[14]

Bit 14: Port x lock pin 14.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[15]

Bit 15: Port x lock pin 15.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCKK

Bit 16: Lok Key.

Allowed values:
0: NotActive: Port configuration lock key not active
1: Active: Port configuration lock key active

AFRL

GPIO alternate function low register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AFR[L7] rw				AFR[L6] rw				AFR[L5] rw				AFR[L4] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AFR[L3] rw				AFR[L2] rw				AFR[L1] rw				AFR[L0] rw

Toggle fields

AFR[L0]

Bits 0-3: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L1]

Bits 4-7: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L2]

Bits 8-11: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L3]

Bits 12-15: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L4]

Bits 16-19: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L5]

Bits 20-23: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L6]

Bits 24-27: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L7]

Bits 28-31: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH

GPIO alternate function high register

Offset: 0x24, size: 32, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AFR[H15] rw				AFR[H14] rw				AFR[H13] rw				AFR[H12] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AFR[H11] rw				AFR[H10] rw				AFR[H9] rw				AFR[H8] rw

Toggle fields

AFR[H8]

Bits 0-3: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H9]

Bits 4-7: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H10]

Bits 8-11: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H11]

Bits 12-15: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H12]

Bits 16-19: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H13]

Bits 20-23: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H14]

Bits 24-27: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H15]

Bits 28-31: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

BRR

Port bit reset register

Offset: 0x28, size: 32, reset: 0x00000000, access: write-only

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BR[15] w	BR[14] w	BR[13] w	BR[12] w	BR[11] w	BR[10] w	BR[9] w	BR[8] w	BR[7] w	BR[6] w	BR[5] w	BR[4] w	BR[3] w	BR[2] w	BR[1] w	BR[0] w

Toggle fields

BR[0]

Bit 0: Port x reset pin 0.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[1]

Bit 1: Port x reset pin 1.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[2]

Bit 2: Port x reset pin 2.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[3]

Bit 3: Port x reset pin 3.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[4]

Bit 4: Port x reset pin 4.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[5]

Bit 5: Port x reset pin 5.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[6]

Bit 6: Port x reset pin 6.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[7]

Bit 7: Port x reset pin 7.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[8]

Bit 8: Port x reset pin 8.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[9]

Bit 9: Port x reset pin 9.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[10]

Bit 10: Port x reset pin 10.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[11]

Bit 11: Port x reset pin 11.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[12]

Bit 12: Port x reset pin 12.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[13]

Bit 13: Port x reset pin 13.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[14]

Bit 14: Port x reset pin 14.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[15]

Bit 15: Port x reset pin 15.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

GPIOD

0x48000c00: General-purpose I/Os

177/177 fields covered.

Toggle register map

Offset	Name	31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	MODER	MODER[15]		MODER[14]		MODER[13]		MODER[12]		MODER[11]		MODER[10]		MODER[9]		MODER[8]		MODER[7]		MODER[6]		MODER[5]		MODER[4]		MODER[3]		MODER[2]		MODER[1]		MODER[0]
0x4	OTYPER																	OT[15]	OT[14]	OT[13]	OT[12]	OT[11]	OT[10]	OT[9]	OT[8]	OT[7]	OT[6]	OT[5]	OT[4]	OT[3]	OT[2]	OT[1]	OT[0]
0x8	OSPEEDR	OSPEEDR[15]		OSPEEDR[14]		OSPEEDR[13]		OSPEEDR[12]		OSPEEDR[11]		OSPEEDR[10]		OSPEEDR[9]		OSPEEDR[8]		OSPEEDR[7]		OSPEEDR[6]		OSPEEDR[5]		OSPEEDR[4]		OSPEEDR[3]		OSPEEDR[2]		OSPEEDR[1]		OSPEEDR[0]
0xc	PUPDR	PUPDR[15]		PUPDR[14]		PUPDR[13]		PUPDR[12]		PUPDR[11]		PUPDR[10]		PUPDR[9]		PUPDR[8]		PUPDR[7]		PUPDR[6]		PUPDR[5]		PUPDR[4]		PUPDR[3]		PUPDR[2]		PUPDR[1]		PUPDR[0]
0x10	IDR																	IDR[15]	IDR[14]	IDR[13]	IDR[12]	IDR[11]	IDR[10]	IDR[9]	IDR[8]	IDR[7]	IDR[6]	IDR[5]	IDR[4]	IDR[3]	IDR[2]	IDR[1]	IDR[0]
0x14	ODR																	ODR[15]	ODR[14]	ODR[13]	ODR[12]	ODR[11]	ODR[10]	ODR[9]	ODR[8]	ODR[7]	ODR[6]	ODR[5]	ODR[4]	ODR[3]	ODR[2]	ODR[1]	ODR[0]
0x18	BSRR	BR[15]	BR[14]	BR[13]	BR[12]	BR[11]	BR[10]	BR[9]	BR[8]	BR[7]	BR[6]	BR[5]	BR[4]	BR[3]	BR[2]	BR[1]	BR[0]	BS[15]	BS[14]	BS[13]	BS[12]	BS[11]	BS[10]	BS[9]	BS[8]	BS[7]	BS[6]	BS[5]	BS[4]	BS[3]	BS[2]	BS[1]	BS[0]
0x1c	LCKR																LCKK	LCK[15]	LCK[14]	LCK[13]	LCK[12]	LCK[11]	LCK[10]	LCK[9]	LCK[8]	LCK[7]	LCK[6]	LCK[5]	LCK[4]	LCK[3]	LCK[2]	LCK[1]	LCK[0]
0x20	AFRL	AFR[L7]				AFR[L6]				AFR[L5]				AFR[L4]				AFR[L3]				AFR[L2]				AFR[L1]				AFR[L0]
0x24	AFRH	AFR[H15]				AFR[H14]				AFR[H13]				AFR[H12]				AFR[H11]				AFR[H10]				AFR[H9]				AFR[H8]
0x28	BRR																	BR[15]	BR[14]	BR[13]	BR[12]	BR[11]	BR[10]	BR[9]	BR[8]	BR[7]	BR[6]	BR[5]	BR[4]	BR[3]	BR[2]	BR[1]	BR[0]

Toggle registers

MODER

GPIO port mode register

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MODER[15] rw		MODER[14] rw		MODER[13] rw		MODER[12] rw		MODER[11] rw		MODER[10] rw		MODER[9] rw		MODER[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MODER[7] rw		MODER[6] rw		MODER[5] rw		MODER[4] rw		MODER[3] rw		MODER[2] rw		MODER[1] rw		MODER[0] rw

Toggle fields

MODER[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

OTYPER

GPIO port output type register

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OT[15] rw	OT[14] rw	OT[13] rw	OT[12] rw	OT[11] rw	OT[10] rw	OT[9] rw	OT[8] rw	OT[7] rw	OT[6] rw	OT[5] rw	OT[4] rw	OT[3] rw	OT[2] rw	OT[1] rw	OT[0] rw

Toggle fields

OT[0]

Bit 0: Port x configuration pin 0.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[1]

Bit 1: Port x configuration pin 1.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[2]

Bit 2: Port x configuration pin 2.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[3]

Bit 3: Port x configuration pin 3.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[4]

Bit 4: Port x configuration pin 4.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[5]

Bit 5: Port x configuration pin 5.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[6]

Bit 6: Port x configuration pin 6.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[7]

Bit 7: Port x configuration pin 7.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[8]

Bit 8: Port x configuration pin 8.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[9]

Bit 9: Port x configuration pin 9.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[10]

Bit 10: Port x configuration pin 10.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[11]

Bit 11: Port x configuration pin 11.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[12]

Bit 12: Port x configuration pin 12.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[13]

Bit 13: Port x configuration pin 13.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[14]

Bit 14: Port x configuration pin 14.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[15]

Bit 15: Port x configuration pin 15.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OSPEEDR

GPIO port output speed register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OSPEEDR[15] rw		OSPEEDR[14] rw		OSPEEDR[13] rw		OSPEEDR[12] rw		OSPEEDR[11] rw		OSPEEDR[10] rw		OSPEEDR[9] rw		OSPEEDR[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OSPEEDR[7] rw		OSPEEDR[6] rw		OSPEEDR[5] rw		OSPEEDR[4] rw		OSPEEDR[3] rw		OSPEEDR[2] rw		OSPEEDR[1] rw		OSPEEDR[0] rw

Toggle fields

OSPEEDR[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

PUPDR

GPIO port pull-up/pull-down register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PUPDR[15] rw		PUPDR[14] rw		PUPDR[13] rw		PUPDR[12] rw		PUPDR[11] rw		PUPDR[10] rw		PUPDR[9] rw		PUPDR[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PUPDR[7] rw		PUPDR[6] rw		PUPDR[5] rw		PUPDR[4] rw		PUPDR[3] rw		PUPDR[2] rw		PUPDR[1] rw		PUPDR[0] rw

Toggle fields

PUPDR[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

IDR

GPIO port input data register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-only

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IDR[15] r	IDR[14] r	IDR[13] r	IDR[12] r	IDR[11] r	IDR[10] r	IDR[9] r	IDR[8] r	IDR[7] r	IDR[6] r	IDR[5] r	IDR[4] r	IDR[3] r	IDR[2] r	IDR[1] r	IDR[0] r

Toggle fields

IDR[0]

Bit 0: Port input data pin 0.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[1]

Bit 1: Port input data pin 1.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[2]

Bit 2: Port input data pin 2.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[3]

Bit 3: Port input data pin 3.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[4]

Bit 4: Port input data pin 4.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[5]

Bit 5: Port input data pin 5.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[6]

Bit 6: Port input data pin 6.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[7]

Bit 7: Port input data pin 7.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[8]

Bit 8: Port input data pin 8.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[9]

Bit 9: Port input data pin 9.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[10]

Bit 10: Port input data pin 10.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[11]

Bit 11: Port input data pin 11.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[12]

Bit 12: Port input data pin 12.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[13]

Bit 13: Port input data pin 13.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[14]

Bit 14: Port input data pin 14.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[15]

Bit 15: Port input data pin 15.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

ODR

GPIO port output data register

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ODR[15] rw	ODR[14] rw	ODR[13] rw	ODR[12] rw	ODR[11] rw	ODR[10] rw	ODR[9] rw	ODR[8] rw	ODR[7] rw	ODR[6] rw	ODR[5] rw	ODR[4] rw	ODR[3] rw	ODR[2] rw	ODR[1] rw	ODR[0] rw

Toggle fields

ODR[0]

Bit 0: Port output data pin 0.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[1]

Bit 1: Port output data pin 1.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[2]

Bit 2: Port output data pin 2.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[3]

Bit 3: Port output data pin 3.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[4]

Bit 4: Port output data pin 4.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[5]

Bit 5: Port output data pin 5.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[6]

Bit 6: Port output data pin 6.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[7]

Bit 7: Port output data pin 7.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[8]

Bit 8: Port output data pin 8.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[9]

Bit 9: Port output data pin 9.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[10]

Bit 10: Port output data pin 10.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[11]

Bit 11: Port output data pin 11.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[12]

Bit 12: Port output data pin 12.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[13]

Bit 13: Port output data pin 13.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[14]

Bit 14: Port output data pin 14.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[15]

Bit 15: Port output data pin 15.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

BSRR

GPIO port bit set/reset register

Offset: 0x18, size: 32, reset: 0x00000000, access: write-only

32/32 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BR[15] w	BR[14] w	BR[13] w	BR[12] w	BR[11] w	BR[10] w	BR[9] w	BR[8] w	BR[7] w	BR[6] w	BR[5] w	BR[4] w	BR[3] w	BR[2] w	BR[1] w	BR[0] w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BS[15] w	BS[14] w	BS[13] w	BS[12] w	BS[11] w	BS[10] w	BS[9] w	BS[8] w	BS[7] w	BS[6] w	BS[5] w	BS[4] w	BS[3] w	BS[2] w	BS[1] w	BS[0] w

Toggle fields

BS[0]

Bit 0: Port x set pin 0.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[1]

Bit 1: Port x set pin 1.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[2]

Bit 2: Port x set pin 2.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[3]

Bit 3: Port x set pin 3.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[4]

Bit 4: Port x set pin 4.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[5]

Bit 5: Port x set pin 5.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[6]

Bit 6: Port x set pin 6.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[7]

Bit 7: Port x set pin 7.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[8]

Bit 8: Port x set pin 8.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[9]

Bit 9: Port x set pin 9.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[10]

Bit 10: Port x set pin 10.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[11]

Bit 11: Port x set pin 11.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[12]

Bit 12: Port x set pin 12.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[13]

Bit 13: Port x set pin 13.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[14]

Bit 14: Port x set pin 14.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[15]

Bit 15: Port x set pin 15.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BR[0]

Bit 16: Port x reset pin 0.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[1]

Bit 17: Port x reset pin 1.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[2]

Bit 18: Port x reset pin 2.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[3]

Bit 19: Port x reset pin 3.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[4]

Bit 20: Port x reset pin 4.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[5]

Bit 21: Port x reset pin 5.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[6]

Bit 22: Port x reset pin 6.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[7]

Bit 23: Port x reset pin 7.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[8]

Bit 24: Port x reset pin 8.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[9]

Bit 25: Port x reset pin 9.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[10]

Bit 26: Port x reset pin 10.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[11]

Bit 27: Port x reset pin 11.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[12]

Bit 28: Port x reset pin 12.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[13]

Bit 29: Port x reset pin 13.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[14]

Bit 30: Port x reset pin 14.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[15]

Bit 31: Port x reset pin 15.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

LCKR

GPIO port configuration lock register

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

17/17 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															LCKK rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
LCK[15] rw	LCK[14] rw	LCK[13] rw	LCK[12] rw	LCK[11] rw	LCK[10] rw	LCK[9] rw	LCK[8] rw	LCK[7] rw	LCK[6] rw	LCK[5] rw	LCK[4] rw	LCK[3] rw	LCK[2] rw	LCK[1] rw	LCK[0] rw

Toggle fields

LCK[0]

Bit 0: Port x lock pin 0.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[1]

Bit 1: Port x lock pin 1.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[2]

Bit 2: Port x lock pin 2.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[3]

Bit 3: Port x lock pin 3.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[4]

Bit 4: Port x lock pin 4.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[5]

Bit 5: Port x lock pin 5.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[6]

Bit 6: Port x lock pin 6.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[7]

Bit 7: Port x lock pin 7.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[8]

Bit 8: Port x lock pin 8.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[9]

Bit 9: Port x lock pin 9.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[10]

Bit 10: Port x lock pin 10.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[11]

Bit 11: Port x lock pin 11.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[12]

Bit 12: Port x lock pin 12.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[13]

Bit 13: Port x lock pin 13.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[14]

Bit 14: Port x lock pin 14.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[15]

Bit 15: Port x lock pin 15.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCKK

Bit 16: Lok Key.

Allowed values:
0: NotActive: Port configuration lock key not active
1: Active: Port configuration lock key active

AFRL

GPIO alternate function low register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AFR[L7] rw				AFR[L6] rw				AFR[L5] rw				AFR[L4] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AFR[L3] rw				AFR[L2] rw				AFR[L1] rw				AFR[L0] rw

Toggle fields

AFR[L0]

Bits 0-3: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L1]

Bits 4-7: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L2]

Bits 8-11: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L3]

Bits 12-15: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L4]

Bits 16-19: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L5]

Bits 20-23: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L6]

Bits 24-27: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L7]

Bits 28-31: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH

GPIO alternate function high register

Offset: 0x24, size: 32, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AFR[H15] rw				AFR[H14] rw				AFR[H13] rw				AFR[H12] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AFR[H11] rw				AFR[H10] rw				AFR[H9] rw				AFR[H8] rw

Toggle fields

AFR[H8]

Bits 0-3: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H9]

Bits 4-7: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H10]

Bits 8-11: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H11]

Bits 12-15: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H12]

Bits 16-19: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H13]

Bits 20-23: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H14]

Bits 24-27: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H15]

Bits 28-31: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

BRR

Port bit reset register

Offset: 0x28, size: 32, reset: 0x00000000, access: write-only

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BR[15] w	BR[14] w	BR[13] w	BR[12] w	BR[11] w	BR[10] w	BR[9] w	BR[8] w	BR[7] w	BR[6] w	BR[5] w	BR[4] w	BR[3] w	BR[2] w	BR[1] w	BR[0] w

Toggle fields

BR[0]

Bit 0: Port x reset pin 0.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[1]

Bit 1: Port x reset pin 1.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[2]

Bit 2: Port x reset pin 2.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[3]

Bit 3: Port x reset pin 3.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[4]

Bit 4: Port x reset pin 4.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[5]

Bit 5: Port x reset pin 5.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[6]

Bit 6: Port x reset pin 6.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[7]

Bit 7: Port x reset pin 7.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[8]

Bit 8: Port x reset pin 8.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[9]

Bit 9: Port x reset pin 9.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[10]

Bit 10: Port x reset pin 10.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[11]

Bit 11: Port x reset pin 11.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[12]

Bit 12: Port x reset pin 12.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[13]

Bit 13: Port x reset pin 13.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[14]

Bit 14: Port x reset pin 14.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[15]

Bit 15: Port x reset pin 15.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

GPIOE

0x48001000: General-purpose I/Os

177/177 fields covered.

Toggle register map

Offset	Name	31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	MODER	MODER[15]		MODER[14]		MODER[13]		MODER[12]		MODER[11]		MODER[10]		MODER[9]		MODER[8]		MODER[7]		MODER[6]		MODER[5]		MODER[4]		MODER[3]		MODER[2]		MODER[1]		MODER[0]
0x4	OTYPER																	OT[15]	OT[14]	OT[13]	OT[12]	OT[11]	OT[10]	OT[9]	OT[8]	OT[7]	OT[6]	OT[5]	OT[4]	OT[3]	OT[2]	OT[1]	OT[0]
0x8	OSPEEDR	OSPEEDR[15]		OSPEEDR[14]		OSPEEDR[13]		OSPEEDR[12]		OSPEEDR[11]		OSPEEDR[10]		OSPEEDR[9]		OSPEEDR[8]		OSPEEDR[7]		OSPEEDR[6]		OSPEEDR[5]		OSPEEDR[4]		OSPEEDR[3]		OSPEEDR[2]		OSPEEDR[1]		OSPEEDR[0]
0xc	PUPDR	PUPDR[15]		PUPDR[14]		PUPDR[13]		PUPDR[12]		PUPDR[11]		PUPDR[10]		PUPDR[9]		PUPDR[8]		PUPDR[7]		PUPDR[6]		PUPDR[5]		PUPDR[4]		PUPDR[3]		PUPDR[2]		PUPDR[1]		PUPDR[0]
0x10	IDR																	IDR[15]	IDR[14]	IDR[13]	IDR[12]	IDR[11]	IDR[10]	IDR[9]	IDR[8]	IDR[7]	IDR[6]	IDR[5]	IDR[4]	IDR[3]	IDR[2]	IDR[1]	IDR[0]
0x14	ODR																	ODR[15]	ODR[14]	ODR[13]	ODR[12]	ODR[11]	ODR[10]	ODR[9]	ODR[8]	ODR[7]	ODR[6]	ODR[5]	ODR[4]	ODR[3]	ODR[2]	ODR[1]	ODR[0]
0x18	BSRR	BR[15]	BR[14]	BR[13]	BR[12]	BR[11]	BR[10]	BR[9]	BR[8]	BR[7]	BR[6]	BR[5]	BR[4]	BR[3]	BR[2]	BR[1]	BR[0]	BS[15]	BS[14]	BS[13]	BS[12]	BS[11]	BS[10]	BS[9]	BS[8]	BS[7]	BS[6]	BS[5]	BS[4]	BS[3]	BS[2]	BS[1]	BS[0]
0x1c	LCKR																LCKK	LCK[15]	LCK[14]	LCK[13]	LCK[12]	LCK[11]	LCK[10]	LCK[9]	LCK[8]	LCK[7]	LCK[6]	LCK[5]	LCK[4]	LCK[3]	LCK[2]	LCK[1]	LCK[0]
0x20	AFRL	AFR[L7]				AFR[L6]				AFR[L5]				AFR[L4]				AFR[L3]				AFR[L2]				AFR[L1]				AFR[L0]
0x24	AFRH	AFR[H15]				AFR[H14]				AFR[H13]				AFR[H12]				AFR[H11]				AFR[H10]				AFR[H9]				AFR[H8]
0x28	BRR																	BR[15]	BR[14]	BR[13]	BR[12]	BR[11]	BR[10]	BR[9]	BR[8]	BR[7]	BR[6]	BR[5]	BR[4]	BR[3]	BR[2]	BR[1]	BR[0]

Toggle registers

MODER

GPIO port mode register

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MODER[15] rw		MODER[14] rw		MODER[13] rw		MODER[12] rw		MODER[11] rw		MODER[10] rw		MODER[9] rw		MODER[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MODER[7] rw		MODER[6] rw		MODER[5] rw		MODER[4] rw		MODER[3] rw		MODER[2] rw		MODER[1] rw		MODER[0] rw

Toggle fields

MODER[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

OTYPER

GPIO port output type register

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OT[15] rw	OT[14] rw	OT[13] rw	OT[12] rw	OT[11] rw	OT[10] rw	OT[9] rw	OT[8] rw	OT[7] rw	OT[6] rw	OT[5] rw	OT[4] rw	OT[3] rw	OT[2] rw	OT[1] rw	OT[0] rw

Toggle fields

OT[0]

Bit 0: Port x configuration pin 0.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[1]

Bit 1: Port x configuration pin 1.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[2]

Bit 2: Port x configuration pin 2.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[3]

Bit 3: Port x configuration pin 3.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[4]

Bit 4: Port x configuration pin 4.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[5]

Bit 5: Port x configuration pin 5.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[6]

Bit 6: Port x configuration pin 6.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[7]

Bit 7: Port x configuration pin 7.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[8]

Bit 8: Port x configuration pin 8.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[9]

Bit 9: Port x configuration pin 9.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[10]

Bit 10: Port x configuration pin 10.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[11]

Bit 11: Port x configuration pin 11.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[12]

Bit 12: Port x configuration pin 12.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[13]

Bit 13: Port x configuration pin 13.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[14]

Bit 14: Port x configuration pin 14.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[15]

Bit 15: Port x configuration pin 15.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OSPEEDR

GPIO port output speed register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OSPEEDR[15] rw		OSPEEDR[14] rw		OSPEEDR[13] rw		OSPEEDR[12] rw		OSPEEDR[11] rw		OSPEEDR[10] rw		OSPEEDR[9] rw		OSPEEDR[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OSPEEDR[7] rw		OSPEEDR[6] rw		OSPEEDR[5] rw		OSPEEDR[4] rw		OSPEEDR[3] rw		OSPEEDR[2] rw		OSPEEDR[1] rw		OSPEEDR[0] rw

Toggle fields

OSPEEDR[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

PUPDR

GPIO port pull-up/pull-down register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PUPDR[15] rw		PUPDR[14] rw		PUPDR[13] rw		PUPDR[12] rw		PUPDR[11] rw		PUPDR[10] rw		PUPDR[9] rw		PUPDR[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PUPDR[7] rw		PUPDR[6] rw		PUPDR[5] rw		PUPDR[4] rw		PUPDR[3] rw		PUPDR[2] rw		PUPDR[1] rw		PUPDR[0] rw

Toggle fields

PUPDR[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

IDR

GPIO port input data register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-only

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IDR[15] r	IDR[14] r	IDR[13] r	IDR[12] r	IDR[11] r	IDR[10] r	IDR[9] r	IDR[8] r	IDR[7] r	IDR[6] r	IDR[5] r	IDR[4] r	IDR[3] r	IDR[2] r	IDR[1] r	IDR[0] r

Toggle fields

IDR[0]

Bit 0: Port input data pin 0.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[1]

Bit 1: Port input data pin 1.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[2]

Bit 2: Port input data pin 2.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[3]

Bit 3: Port input data pin 3.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[4]

Bit 4: Port input data pin 4.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[5]

Bit 5: Port input data pin 5.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[6]

Bit 6: Port input data pin 6.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[7]

Bit 7: Port input data pin 7.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[8]

Bit 8: Port input data pin 8.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[9]

Bit 9: Port input data pin 9.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[10]

Bit 10: Port input data pin 10.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[11]

Bit 11: Port input data pin 11.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[12]

Bit 12: Port input data pin 12.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[13]

Bit 13: Port input data pin 13.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[14]

Bit 14: Port input data pin 14.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[15]

Bit 15: Port input data pin 15.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

ODR

GPIO port output data register

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ODR[15] rw	ODR[14] rw	ODR[13] rw	ODR[12] rw	ODR[11] rw	ODR[10] rw	ODR[9] rw	ODR[8] rw	ODR[7] rw	ODR[6] rw	ODR[5] rw	ODR[4] rw	ODR[3] rw	ODR[2] rw	ODR[1] rw	ODR[0] rw

Toggle fields

ODR[0]

Bit 0: Port output data pin 0.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[1]

Bit 1: Port output data pin 1.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[2]

Bit 2: Port output data pin 2.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[3]

Bit 3: Port output data pin 3.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[4]

Bit 4: Port output data pin 4.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[5]

Bit 5: Port output data pin 5.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[6]

Bit 6: Port output data pin 6.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[7]

Bit 7: Port output data pin 7.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[8]

Bit 8: Port output data pin 8.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[9]

Bit 9: Port output data pin 9.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[10]

Bit 10: Port output data pin 10.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[11]

Bit 11: Port output data pin 11.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[12]

Bit 12: Port output data pin 12.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[13]

Bit 13: Port output data pin 13.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[14]

Bit 14: Port output data pin 14.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[15]

Bit 15: Port output data pin 15.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

BSRR

GPIO port bit set/reset register

Offset: 0x18, size: 32, reset: 0x00000000, access: write-only

32/32 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BR[15] w	BR[14] w	BR[13] w	BR[12] w	BR[11] w	BR[10] w	BR[9] w	BR[8] w	BR[7] w	BR[6] w	BR[5] w	BR[4] w	BR[3] w	BR[2] w	BR[1] w	BR[0] w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BS[15] w	BS[14] w	BS[13] w	BS[12] w	BS[11] w	BS[10] w	BS[9] w	BS[8] w	BS[7] w	BS[6] w	BS[5] w	BS[4] w	BS[3] w	BS[2] w	BS[1] w	BS[0] w

Toggle fields

BS[0]

Bit 0: Port x set pin 0.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[1]

Bit 1: Port x set pin 1.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[2]

Bit 2: Port x set pin 2.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[3]

Bit 3: Port x set pin 3.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[4]

Bit 4: Port x set pin 4.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[5]

Bit 5: Port x set pin 5.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[6]

Bit 6: Port x set pin 6.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[7]

Bit 7: Port x set pin 7.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[8]

Bit 8: Port x set pin 8.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[9]

Bit 9: Port x set pin 9.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[10]

Bit 10: Port x set pin 10.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[11]

Bit 11: Port x set pin 11.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[12]

Bit 12: Port x set pin 12.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[13]

Bit 13: Port x set pin 13.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[14]

Bit 14: Port x set pin 14.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[15]

Bit 15: Port x set pin 15.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BR[0]

Bit 16: Port x reset pin 0.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[1]

Bit 17: Port x reset pin 1.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[2]

Bit 18: Port x reset pin 2.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[3]

Bit 19: Port x reset pin 3.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[4]

Bit 20: Port x reset pin 4.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[5]

Bit 21: Port x reset pin 5.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[6]

Bit 22: Port x reset pin 6.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[7]

Bit 23: Port x reset pin 7.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[8]

Bit 24: Port x reset pin 8.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[9]

Bit 25: Port x reset pin 9.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[10]

Bit 26: Port x reset pin 10.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[11]

Bit 27: Port x reset pin 11.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[12]

Bit 28: Port x reset pin 12.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[13]

Bit 29: Port x reset pin 13.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[14]

Bit 30: Port x reset pin 14.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[15]

Bit 31: Port x reset pin 15.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

LCKR

GPIO port configuration lock register

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

17/17 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															LCKK rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
LCK[15] rw	LCK[14] rw	LCK[13] rw	LCK[12] rw	LCK[11] rw	LCK[10] rw	LCK[9] rw	LCK[8] rw	LCK[7] rw	LCK[6] rw	LCK[5] rw	LCK[4] rw	LCK[3] rw	LCK[2] rw	LCK[1] rw	LCK[0] rw

Toggle fields

LCK[0]

Bit 0: Port x lock pin 0.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[1]

Bit 1: Port x lock pin 1.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[2]

Bit 2: Port x lock pin 2.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[3]

Bit 3: Port x lock pin 3.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[4]

Bit 4: Port x lock pin 4.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[5]

Bit 5: Port x lock pin 5.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[6]

Bit 6: Port x lock pin 6.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[7]

Bit 7: Port x lock pin 7.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[8]

Bit 8: Port x lock pin 8.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[9]

Bit 9: Port x lock pin 9.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[10]

Bit 10: Port x lock pin 10.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[11]

Bit 11: Port x lock pin 11.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[12]

Bit 12: Port x lock pin 12.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[13]

Bit 13: Port x lock pin 13.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[14]

Bit 14: Port x lock pin 14.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[15]

Bit 15: Port x lock pin 15.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCKK

Bit 16: Lok Key.

Allowed values:
0: NotActive: Port configuration lock key not active
1: Active: Port configuration lock key active

AFRL

GPIO alternate function low register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AFR[L7] rw				AFR[L6] rw				AFR[L5] rw				AFR[L4] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AFR[L3] rw				AFR[L2] rw				AFR[L1] rw				AFR[L0] rw

Toggle fields

AFR[L0]

Bits 0-3: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L1]

Bits 4-7: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L2]

Bits 8-11: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L3]

Bits 12-15: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L4]

Bits 16-19: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L5]

Bits 20-23: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L6]

Bits 24-27: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L7]

Bits 28-31: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH

GPIO alternate function high register

Offset: 0x24, size: 32, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AFR[H15] rw				AFR[H14] rw				AFR[H13] rw				AFR[H12] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AFR[H11] rw				AFR[H10] rw				AFR[H9] rw				AFR[H8] rw

Toggle fields

AFR[H8]

Bits 0-3: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H9]

Bits 4-7: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H10]

Bits 8-11: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H11]

Bits 12-15: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H12]

Bits 16-19: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H13]

Bits 20-23: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H14]

Bits 24-27: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H15]

Bits 28-31: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

BRR

Port bit reset register

Offset: 0x28, size: 32, reset: 0x00000000, access: write-only

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BR[15] w	BR[14] w	BR[13] w	BR[12] w	BR[11] w	BR[10] w	BR[9] w	BR[8] w	BR[7] w	BR[6] w	BR[5] w	BR[4] w	BR[3] w	BR[2] w	BR[1] w	BR[0] w

Toggle fields

BR[0]

Bit 0: Port x reset pin 0.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[1]

Bit 1: Port x reset pin 1.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[2]

Bit 2: Port x reset pin 2.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[3]

Bit 3: Port x reset pin 3.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[4]

Bit 4: Port x reset pin 4.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[5]

Bit 5: Port x reset pin 5.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[6]

Bit 6: Port x reset pin 6.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[7]

Bit 7: Port x reset pin 7.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[8]

Bit 8: Port x reset pin 8.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[9]

Bit 9: Port x reset pin 9.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[10]

Bit 10: Port x reset pin 10.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[11]

Bit 11: Port x reset pin 11.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[12]

Bit 12: Port x reset pin 12.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[13]

Bit 13: Port x reset pin 13.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[14]

Bit 14: Port x reset pin 14.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[15]

Bit 15: Port x reset pin 15.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

GPIOF

0x48001400: General-purpose I/Os

177/177 fields covered.

Toggle register map

Offset	Name	31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	MODER	MODER[15]		MODER[14]		MODER[13]		MODER[12]		MODER[11]		MODER[10]		MODER[9]		MODER[8]		MODER[7]		MODER[6]		MODER[5]		MODER[4]		MODER[3]		MODER[2]		MODER[1]		MODER[0]
0x4	OTYPER																	OT[15]	OT[14]	OT[13]	OT[12]	OT[11]	OT[10]	OT[9]	OT[8]	OT[7]	OT[6]	OT[5]	OT[4]	OT[3]	OT[2]	OT[1]	OT[0]
0x8	OSPEEDR	OSPEEDR[15]		OSPEEDR[14]		OSPEEDR[13]		OSPEEDR[12]		OSPEEDR[11]		OSPEEDR[10]		OSPEEDR[9]		OSPEEDR[8]		OSPEEDR[7]		OSPEEDR[6]		OSPEEDR[5]		OSPEEDR[4]		OSPEEDR[3]		OSPEEDR[2]		OSPEEDR[1]		OSPEEDR[0]
0xc	PUPDR	PUPDR[15]		PUPDR[14]		PUPDR[13]		PUPDR[12]		PUPDR[11]		PUPDR[10]		PUPDR[9]		PUPDR[8]		PUPDR[7]		PUPDR[6]		PUPDR[5]		PUPDR[4]		PUPDR[3]		PUPDR[2]		PUPDR[1]		PUPDR[0]
0x10	IDR																	IDR[15]	IDR[14]	IDR[13]	IDR[12]	IDR[11]	IDR[10]	IDR[9]	IDR[8]	IDR[7]	IDR[6]	IDR[5]	IDR[4]	IDR[3]	IDR[2]	IDR[1]	IDR[0]
0x14	ODR																	ODR[15]	ODR[14]	ODR[13]	ODR[12]	ODR[11]	ODR[10]	ODR[9]	ODR[8]	ODR[7]	ODR[6]	ODR[5]	ODR[4]	ODR[3]	ODR[2]	ODR[1]	ODR[0]
0x18	BSRR	BR[15]	BR[14]	BR[13]	BR[12]	BR[11]	BR[10]	BR[9]	BR[8]	BR[7]	BR[6]	BR[5]	BR[4]	BR[3]	BR[2]	BR[1]	BR[0]	BS[15]	BS[14]	BS[13]	BS[12]	BS[11]	BS[10]	BS[9]	BS[8]	BS[7]	BS[6]	BS[5]	BS[4]	BS[3]	BS[2]	BS[1]	BS[0]
0x1c	LCKR																LCKK	LCK[15]	LCK[14]	LCK[13]	LCK[12]	LCK[11]	LCK[10]	LCK[9]	LCK[8]	LCK[7]	LCK[6]	LCK[5]	LCK[4]	LCK[3]	LCK[2]	LCK[1]	LCK[0]
0x20	AFRL	AFR[L7]				AFR[L6]				AFR[L5]				AFR[L4]				AFR[L3]				AFR[L2]				AFR[L1]				AFR[L0]
0x24	AFRH	AFR[H15]				AFR[H14]				AFR[H13]				AFR[H12]				AFR[H11]				AFR[H10]				AFR[H9]				AFR[H8]
0x28	BRR																	BR[15]	BR[14]	BR[13]	BR[12]	BR[11]	BR[10]	BR[9]	BR[8]	BR[7]	BR[6]	BR[5]	BR[4]	BR[3]	BR[2]	BR[1]	BR[0]

Toggle registers

MODER

GPIO port mode register

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MODER[15] rw		MODER[14] rw		MODER[13] rw		MODER[12] rw		MODER[11] rw		MODER[10] rw		MODER[9] rw		MODER[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MODER[7] rw		MODER[6] rw		MODER[5] rw		MODER[4] rw		MODER[3] rw		MODER[2] rw		MODER[1] rw		MODER[0] rw

Toggle fields

MODER[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

OTYPER

GPIO port output type register

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OT[15] rw	OT[14] rw	OT[13] rw	OT[12] rw	OT[11] rw	OT[10] rw	OT[9] rw	OT[8] rw	OT[7] rw	OT[6] rw	OT[5] rw	OT[4] rw	OT[3] rw	OT[2] rw	OT[1] rw	OT[0] rw

Toggle fields

OT[0]

Bit 0: Port x configuration pin 0.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[1]

Bit 1: Port x configuration pin 1.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[2]

Bit 2: Port x configuration pin 2.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[3]

Bit 3: Port x configuration pin 3.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[4]

Bit 4: Port x configuration pin 4.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[5]

Bit 5: Port x configuration pin 5.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[6]

Bit 6: Port x configuration pin 6.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[7]

Bit 7: Port x configuration pin 7.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[8]

Bit 8: Port x configuration pin 8.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[9]

Bit 9: Port x configuration pin 9.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[10]

Bit 10: Port x configuration pin 10.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[11]

Bit 11: Port x configuration pin 11.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[12]

Bit 12: Port x configuration pin 12.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[13]

Bit 13: Port x configuration pin 13.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[14]

Bit 14: Port x configuration pin 14.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[15]

Bit 15: Port x configuration pin 15.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OSPEEDR

GPIO port output speed register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OSPEEDR[15] rw		OSPEEDR[14] rw		OSPEEDR[13] rw		OSPEEDR[12] rw		OSPEEDR[11] rw		OSPEEDR[10] rw		OSPEEDR[9] rw		OSPEEDR[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OSPEEDR[7] rw		OSPEEDR[6] rw		OSPEEDR[5] rw		OSPEEDR[4] rw		OSPEEDR[3] rw		OSPEEDR[2] rw		OSPEEDR[1] rw		OSPEEDR[0] rw

Toggle fields

OSPEEDR[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

PUPDR

GPIO port pull-up/pull-down register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PUPDR[15] rw		PUPDR[14] rw		PUPDR[13] rw		PUPDR[12] rw		PUPDR[11] rw		PUPDR[10] rw		PUPDR[9] rw		PUPDR[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PUPDR[7] rw		PUPDR[6] rw		PUPDR[5] rw		PUPDR[4] rw		PUPDR[3] rw		PUPDR[2] rw		PUPDR[1] rw		PUPDR[0] rw

Toggle fields

PUPDR[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

IDR

GPIO port input data register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-only

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IDR[15] r	IDR[14] r	IDR[13] r	IDR[12] r	IDR[11] r	IDR[10] r	IDR[9] r	IDR[8] r	IDR[7] r	IDR[6] r	IDR[5] r	IDR[4] r	IDR[3] r	IDR[2] r	IDR[1] r	IDR[0] r

Toggle fields

IDR[0]

Bit 0: Port input data pin 0.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[1]

Bit 1: Port input data pin 1.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[2]

Bit 2: Port input data pin 2.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[3]

Bit 3: Port input data pin 3.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[4]

Bit 4: Port input data pin 4.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[5]

Bit 5: Port input data pin 5.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[6]

Bit 6: Port input data pin 6.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[7]

Bit 7: Port input data pin 7.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[8]

Bit 8: Port input data pin 8.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[9]

Bit 9: Port input data pin 9.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[10]

Bit 10: Port input data pin 10.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[11]

Bit 11: Port input data pin 11.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[12]

Bit 12: Port input data pin 12.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[13]

Bit 13: Port input data pin 13.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[14]

Bit 14: Port input data pin 14.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[15]

Bit 15: Port input data pin 15.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

ODR

GPIO port output data register

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ODR[15] rw	ODR[14] rw	ODR[13] rw	ODR[12] rw	ODR[11] rw	ODR[10] rw	ODR[9] rw	ODR[8] rw	ODR[7] rw	ODR[6] rw	ODR[5] rw	ODR[4] rw	ODR[3] rw	ODR[2] rw	ODR[1] rw	ODR[0] rw

Toggle fields

ODR[0]

Bit 0: Port output data pin 0.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[1]

Bit 1: Port output data pin 1.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[2]

Bit 2: Port output data pin 2.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[3]

Bit 3: Port output data pin 3.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[4]

Bit 4: Port output data pin 4.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[5]

Bit 5: Port output data pin 5.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[6]

Bit 6: Port output data pin 6.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[7]

Bit 7: Port output data pin 7.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[8]

Bit 8: Port output data pin 8.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[9]

Bit 9: Port output data pin 9.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[10]

Bit 10: Port output data pin 10.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[11]

Bit 11: Port output data pin 11.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[12]

Bit 12: Port output data pin 12.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[13]

Bit 13: Port output data pin 13.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[14]

Bit 14: Port output data pin 14.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[15]

Bit 15: Port output data pin 15.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

BSRR

GPIO port bit set/reset register

Offset: 0x18, size: 32, reset: 0x00000000, access: write-only

32/32 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BR[15] w	BR[14] w	BR[13] w	BR[12] w	BR[11] w	BR[10] w	BR[9] w	BR[8] w	BR[7] w	BR[6] w	BR[5] w	BR[4] w	BR[3] w	BR[2] w	BR[1] w	BR[0] w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BS[15] w	BS[14] w	BS[13] w	BS[12] w	BS[11] w	BS[10] w	BS[9] w	BS[8] w	BS[7] w	BS[6] w	BS[5] w	BS[4] w	BS[3] w	BS[2] w	BS[1] w	BS[0] w

Toggle fields

BS[0]

Bit 0: Port x set pin 0.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[1]

Bit 1: Port x set pin 1.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[2]

Bit 2: Port x set pin 2.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[3]

Bit 3: Port x set pin 3.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[4]

Bit 4: Port x set pin 4.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[5]

Bit 5: Port x set pin 5.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[6]

Bit 6: Port x set pin 6.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[7]

Bit 7: Port x set pin 7.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[8]

Bit 8: Port x set pin 8.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[9]

Bit 9: Port x set pin 9.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[10]

Bit 10: Port x set pin 10.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[11]

Bit 11: Port x set pin 11.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[12]

Bit 12: Port x set pin 12.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[13]

Bit 13: Port x set pin 13.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[14]

Bit 14: Port x set pin 14.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[15]

Bit 15: Port x set pin 15.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BR[0]

Bit 16: Port x reset pin 0.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[1]

Bit 17: Port x reset pin 1.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[2]

Bit 18: Port x reset pin 2.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[3]

Bit 19: Port x reset pin 3.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[4]

Bit 20: Port x reset pin 4.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[5]

Bit 21: Port x reset pin 5.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[6]

Bit 22: Port x reset pin 6.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[7]

Bit 23: Port x reset pin 7.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[8]

Bit 24: Port x reset pin 8.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[9]

Bit 25: Port x reset pin 9.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[10]

Bit 26: Port x reset pin 10.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[11]

Bit 27: Port x reset pin 11.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[12]

Bit 28: Port x reset pin 12.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[13]

Bit 29: Port x reset pin 13.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[14]

Bit 30: Port x reset pin 14.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[15]

Bit 31: Port x reset pin 15.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

LCKR

GPIO port configuration lock register

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

17/17 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															LCKK rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
LCK[15] rw	LCK[14] rw	LCK[13] rw	LCK[12] rw	LCK[11] rw	LCK[10] rw	LCK[9] rw	LCK[8] rw	LCK[7] rw	LCK[6] rw	LCK[5] rw	LCK[4] rw	LCK[3] rw	LCK[2] rw	LCK[1] rw	LCK[0] rw

Toggle fields

LCK[0]

Bit 0: Port x lock pin 0.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[1]

Bit 1: Port x lock pin 1.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[2]

Bit 2: Port x lock pin 2.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[3]

Bit 3: Port x lock pin 3.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[4]

Bit 4: Port x lock pin 4.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[5]

Bit 5: Port x lock pin 5.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[6]

Bit 6: Port x lock pin 6.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[7]

Bit 7: Port x lock pin 7.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[8]

Bit 8: Port x lock pin 8.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[9]

Bit 9: Port x lock pin 9.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[10]

Bit 10: Port x lock pin 10.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[11]

Bit 11: Port x lock pin 11.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[12]

Bit 12: Port x lock pin 12.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[13]

Bit 13: Port x lock pin 13.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[14]

Bit 14: Port x lock pin 14.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[15]

Bit 15: Port x lock pin 15.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCKK

Bit 16: Lok Key.

Allowed values:
0: NotActive: Port configuration lock key not active
1: Active: Port configuration lock key active

AFRL

GPIO alternate function low register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AFR[L7] rw				AFR[L6] rw				AFR[L5] rw				AFR[L4] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AFR[L3] rw				AFR[L2] rw				AFR[L1] rw				AFR[L0] rw

Toggle fields

AFR[L0]

Bits 0-3: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L1]

Bits 4-7: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L2]

Bits 8-11: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L3]

Bits 12-15: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L4]

Bits 16-19: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L5]

Bits 20-23: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L6]

Bits 24-27: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L7]

Bits 28-31: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH

GPIO alternate function high register

Offset: 0x24, size: 32, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AFR[H15] rw				AFR[H14] rw				AFR[H13] rw				AFR[H12] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AFR[H11] rw				AFR[H10] rw				AFR[H9] rw				AFR[H8] rw

Toggle fields

AFR[H8]

Bits 0-3: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H9]

Bits 4-7: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H10]

Bits 8-11: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H11]

Bits 12-15: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H12]

Bits 16-19: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H13]

Bits 20-23: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H14]

Bits 24-27: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H15]

Bits 28-31: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

BRR

Port bit reset register

Offset: 0x28, size: 32, reset: 0x00000000, access: write-only

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BR[15] w	BR[14] w	BR[13] w	BR[12] w	BR[11] w	BR[10] w	BR[9] w	BR[8] w	BR[7] w	BR[6] w	BR[5] w	BR[4] w	BR[3] w	BR[2] w	BR[1] w	BR[0] w

Toggle fields

BR[0]

Bit 0: Port x reset pin 0.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[1]

Bit 1: Port x reset pin 1.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[2]

Bit 2: Port x reset pin 2.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[3]

Bit 3: Port x reset pin 3.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[4]

Bit 4: Port x reset pin 4.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[5]

Bit 5: Port x reset pin 5.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[6]

Bit 6: Port x reset pin 6.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[7]

Bit 7: Port x reset pin 7.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[8]

Bit 8: Port x reset pin 8.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[9]

Bit 9: Port x reset pin 9.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[10]

Bit 10: Port x reset pin 10.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[11]

Bit 11: Port x reset pin 11.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[12]

Bit 12: Port x reset pin 12.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[13]

Bit 13: Port x reset pin 13.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[14]

Bit 14: Port x reset pin 14.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[15]

Bit 15: Port x reset pin 15.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

GPIOG

0x48001800: General-purpose I/Os

177/177 fields covered.

Toggle register map

Offset	Name	31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	MODER	MODER[15]		MODER[14]		MODER[13]		MODER[12]		MODER[11]		MODER[10]		MODER[9]		MODER[8]		MODER[7]		MODER[6]		MODER[5]		MODER[4]		MODER[3]		MODER[2]		MODER[1]		MODER[0]
0x4	OTYPER																	OT[15]	OT[14]	OT[13]	OT[12]	OT[11]	OT[10]	OT[9]	OT[8]	OT[7]	OT[6]	OT[5]	OT[4]	OT[3]	OT[2]	OT[1]	OT[0]
0x8	OSPEEDR	OSPEEDR[15]		OSPEEDR[14]		OSPEEDR[13]		OSPEEDR[12]		OSPEEDR[11]		OSPEEDR[10]		OSPEEDR[9]		OSPEEDR[8]		OSPEEDR[7]		OSPEEDR[6]		OSPEEDR[5]		OSPEEDR[4]		OSPEEDR[3]		OSPEEDR[2]		OSPEEDR[1]		OSPEEDR[0]
0xc	PUPDR	PUPDR[15]		PUPDR[14]		PUPDR[13]		PUPDR[12]		PUPDR[11]		PUPDR[10]		PUPDR[9]		PUPDR[8]		PUPDR[7]		PUPDR[6]		PUPDR[5]		PUPDR[4]		PUPDR[3]		PUPDR[2]		PUPDR[1]		PUPDR[0]
0x10	IDR																	IDR[15]	IDR[14]	IDR[13]	IDR[12]	IDR[11]	IDR[10]	IDR[9]	IDR[8]	IDR[7]	IDR[6]	IDR[5]	IDR[4]	IDR[3]	IDR[2]	IDR[1]	IDR[0]
0x14	ODR																	ODR[15]	ODR[14]	ODR[13]	ODR[12]	ODR[11]	ODR[10]	ODR[9]	ODR[8]	ODR[7]	ODR[6]	ODR[5]	ODR[4]	ODR[3]	ODR[2]	ODR[1]	ODR[0]
0x18	BSRR	BR[15]	BR[14]	BR[13]	BR[12]	BR[11]	BR[10]	BR[9]	BR[8]	BR[7]	BR[6]	BR[5]	BR[4]	BR[3]	BR[2]	BR[1]	BR[0]	BS[15]	BS[14]	BS[13]	BS[12]	BS[11]	BS[10]	BS[9]	BS[8]	BS[7]	BS[6]	BS[5]	BS[4]	BS[3]	BS[2]	BS[1]	BS[0]
0x1c	LCKR																LCKK	LCK[15]	LCK[14]	LCK[13]	LCK[12]	LCK[11]	LCK[10]	LCK[9]	LCK[8]	LCK[7]	LCK[6]	LCK[5]	LCK[4]	LCK[3]	LCK[2]	LCK[1]	LCK[0]
0x20	AFRL	AFR[L7]				AFR[L6]				AFR[L5]				AFR[L4]				AFR[L3]				AFR[L2]				AFR[L1]				AFR[L0]
0x24	AFRH	AFR[H15]				AFR[H14]				AFR[H13]				AFR[H12]				AFR[H11]				AFR[H10]				AFR[H9]				AFR[H8]
0x28	BRR																	BR[15]	BR[14]	BR[13]	BR[12]	BR[11]	BR[10]	BR[9]	BR[8]	BR[7]	BR[6]	BR[5]	BR[4]	BR[3]	BR[2]	BR[1]	BR[0]

Toggle registers

MODER

GPIO port mode register

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MODER[15] rw		MODER[14] rw		MODER[13] rw		MODER[12] rw		MODER[11] rw		MODER[10] rw		MODER[9] rw		MODER[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MODER[7] rw		MODER[6] rw		MODER[5] rw		MODER[4] rw		MODER[3] rw		MODER[2] rw		MODER[1] rw		MODER[0] rw

Toggle fields

MODER[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

OTYPER

GPIO port output type register

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OT[15] rw	OT[14] rw	OT[13] rw	OT[12] rw	OT[11] rw	OT[10] rw	OT[9] rw	OT[8] rw	OT[7] rw	OT[6] rw	OT[5] rw	OT[4] rw	OT[3] rw	OT[2] rw	OT[1] rw	OT[0] rw

Toggle fields

OT[0]

Bit 0: Port x configuration pin 0.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[1]

Bit 1: Port x configuration pin 1.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[2]

Bit 2: Port x configuration pin 2.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[3]

Bit 3: Port x configuration pin 3.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[4]

Bit 4: Port x configuration pin 4.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[5]

Bit 5: Port x configuration pin 5.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[6]

Bit 6: Port x configuration pin 6.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[7]

Bit 7: Port x configuration pin 7.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[8]

Bit 8: Port x configuration pin 8.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[9]

Bit 9: Port x configuration pin 9.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[10]

Bit 10: Port x configuration pin 10.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[11]

Bit 11: Port x configuration pin 11.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[12]

Bit 12: Port x configuration pin 12.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[13]

Bit 13: Port x configuration pin 13.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[14]

Bit 14: Port x configuration pin 14.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[15]

Bit 15: Port x configuration pin 15.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OSPEEDR

GPIO port output speed register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OSPEEDR[15] rw		OSPEEDR[14] rw		OSPEEDR[13] rw		OSPEEDR[12] rw		OSPEEDR[11] rw		OSPEEDR[10] rw		OSPEEDR[9] rw		OSPEEDR[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OSPEEDR[7] rw		OSPEEDR[6] rw		OSPEEDR[5] rw		OSPEEDR[4] rw		OSPEEDR[3] rw		OSPEEDR[2] rw		OSPEEDR[1] rw		OSPEEDR[0] rw

Toggle fields

OSPEEDR[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

PUPDR

GPIO port pull-up/pull-down register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PUPDR[15] rw		PUPDR[14] rw		PUPDR[13] rw		PUPDR[12] rw		PUPDR[11] rw		PUPDR[10] rw		PUPDR[9] rw		PUPDR[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PUPDR[7] rw		PUPDR[6] rw		PUPDR[5] rw		PUPDR[4] rw		PUPDR[3] rw		PUPDR[2] rw		PUPDR[1] rw		PUPDR[0] rw

Toggle fields

PUPDR[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

IDR

GPIO port input data register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-only

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IDR[15] r	IDR[14] r	IDR[13] r	IDR[12] r	IDR[11] r	IDR[10] r	IDR[9] r	IDR[8] r	IDR[7] r	IDR[6] r	IDR[5] r	IDR[4] r	IDR[3] r	IDR[2] r	IDR[1] r	IDR[0] r

Toggle fields

IDR[0]

Bit 0: Port input data pin 0.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[1]

Bit 1: Port input data pin 1.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[2]

Bit 2: Port input data pin 2.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[3]

Bit 3: Port input data pin 3.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[4]

Bit 4: Port input data pin 4.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[5]

Bit 5: Port input data pin 5.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[6]

Bit 6: Port input data pin 6.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[7]

Bit 7: Port input data pin 7.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[8]

Bit 8: Port input data pin 8.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[9]

Bit 9: Port input data pin 9.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[10]

Bit 10: Port input data pin 10.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[11]

Bit 11: Port input data pin 11.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[12]

Bit 12: Port input data pin 12.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[13]

Bit 13: Port input data pin 13.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[14]

Bit 14: Port input data pin 14.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[15]

Bit 15: Port input data pin 15.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

ODR

GPIO port output data register

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ODR[15] rw	ODR[14] rw	ODR[13] rw	ODR[12] rw	ODR[11] rw	ODR[10] rw	ODR[9] rw	ODR[8] rw	ODR[7] rw	ODR[6] rw	ODR[5] rw	ODR[4] rw	ODR[3] rw	ODR[2] rw	ODR[1] rw	ODR[0] rw

Toggle fields

ODR[0]

Bit 0: Port output data pin 0.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[1]

Bit 1: Port output data pin 1.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[2]

Bit 2: Port output data pin 2.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[3]

Bit 3: Port output data pin 3.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[4]

Bit 4: Port output data pin 4.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[5]

Bit 5: Port output data pin 5.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[6]

Bit 6: Port output data pin 6.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[7]

Bit 7: Port output data pin 7.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[8]

Bit 8: Port output data pin 8.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[9]

Bit 9: Port output data pin 9.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[10]

Bit 10: Port output data pin 10.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[11]

Bit 11: Port output data pin 11.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[12]

Bit 12: Port output data pin 12.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[13]

Bit 13: Port output data pin 13.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[14]

Bit 14: Port output data pin 14.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[15]

Bit 15: Port output data pin 15.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

BSRR

GPIO port bit set/reset register

Offset: 0x18, size: 32, reset: 0x00000000, access: write-only

32/32 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BR[15] w	BR[14] w	BR[13] w	BR[12] w	BR[11] w	BR[10] w	BR[9] w	BR[8] w	BR[7] w	BR[6] w	BR[5] w	BR[4] w	BR[3] w	BR[2] w	BR[1] w	BR[0] w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BS[15] w	BS[14] w	BS[13] w	BS[12] w	BS[11] w	BS[10] w	BS[9] w	BS[8] w	BS[7] w	BS[6] w	BS[5] w	BS[4] w	BS[3] w	BS[2] w	BS[1] w	BS[0] w

Toggle fields

BS[0]

Bit 0: Port x set pin 0.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[1]

Bit 1: Port x set pin 1.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[2]

Bit 2: Port x set pin 2.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[3]

Bit 3: Port x set pin 3.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[4]

Bit 4: Port x set pin 4.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[5]

Bit 5: Port x set pin 5.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[6]

Bit 6: Port x set pin 6.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[7]

Bit 7: Port x set pin 7.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[8]

Bit 8: Port x set pin 8.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[9]

Bit 9: Port x set pin 9.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[10]

Bit 10: Port x set pin 10.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[11]

Bit 11: Port x set pin 11.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[12]

Bit 12: Port x set pin 12.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[13]

Bit 13: Port x set pin 13.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[14]

Bit 14: Port x set pin 14.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[15]

Bit 15: Port x set pin 15.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BR[0]

Bit 16: Port x reset pin 0.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[1]

Bit 17: Port x reset pin 1.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[2]

Bit 18: Port x reset pin 2.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[3]

Bit 19: Port x reset pin 3.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[4]

Bit 20: Port x reset pin 4.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[5]

Bit 21: Port x reset pin 5.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[6]

Bit 22: Port x reset pin 6.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[7]

Bit 23: Port x reset pin 7.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[8]

Bit 24: Port x reset pin 8.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[9]

Bit 25: Port x reset pin 9.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[10]

Bit 26: Port x reset pin 10.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[11]

Bit 27: Port x reset pin 11.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[12]

Bit 28: Port x reset pin 12.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[13]

Bit 29: Port x reset pin 13.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[14]

Bit 30: Port x reset pin 14.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[15]

Bit 31: Port x reset pin 15.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

LCKR

GPIO port configuration lock register

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

17/17 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															LCKK rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
LCK[15] rw	LCK[14] rw	LCK[13] rw	LCK[12] rw	LCK[11] rw	LCK[10] rw	LCK[9] rw	LCK[8] rw	LCK[7] rw	LCK[6] rw	LCK[5] rw	LCK[4] rw	LCK[3] rw	LCK[2] rw	LCK[1] rw	LCK[0] rw

Toggle fields

LCK[0]

Bit 0: Port x lock pin 0.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[1]

Bit 1: Port x lock pin 1.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[2]

Bit 2: Port x lock pin 2.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[3]

Bit 3: Port x lock pin 3.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[4]

Bit 4: Port x lock pin 4.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[5]

Bit 5: Port x lock pin 5.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[6]

Bit 6: Port x lock pin 6.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[7]

Bit 7: Port x lock pin 7.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[8]

Bit 8: Port x lock pin 8.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[9]

Bit 9: Port x lock pin 9.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[10]

Bit 10: Port x lock pin 10.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[11]

Bit 11: Port x lock pin 11.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[12]

Bit 12: Port x lock pin 12.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[13]

Bit 13: Port x lock pin 13.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[14]

Bit 14: Port x lock pin 14.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[15]

Bit 15: Port x lock pin 15.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCKK

Bit 16: Lok Key.

Allowed values:
0: NotActive: Port configuration lock key not active
1: Active: Port configuration lock key active

AFRL

GPIO alternate function low register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AFR[L7] rw				AFR[L6] rw				AFR[L5] rw				AFR[L4] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AFR[L3] rw				AFR[L2] rw				AFR[L1] rw				AFR[L0] rw

Toggle fields

AFR[L0]

Bits 0-3: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L1]

Bits 4-7: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L2]

Bits 8-11: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L3]

Bits 12-15: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L4]

Bits 16-19: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L5]

Bits 20-23: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L6]

Bits 24-27: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L7]

Bits 28-31: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH

GPIO alternate function high register

Offset: 0x24, size: 32, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AFR[H15] rw				AFR[H14] rw				AFR[H13] rw				AFR[H12] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AFR[H11] rw				AFR[H10] rw				AFR[H9] rw				AFR[H8] rw

Toggle fields

AFR[H8]

Bits 0-3: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H9]

Bits 4-7: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H10]

Bits 8-11: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H11]

Bits 12-15: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H12]

Bits 16-19: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H13]

Bits 20-23: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H14]

Bits 24-27: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H15]

Bits 28-31: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

BRR

Port bit reset register

Offset: 0x28, size: 32, reset: 0x00000000, access: write-only

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BR[15] w	BR[14] w	BR[13] w	BR[12] w	BR[11] w	BR[10] w	BR[9] w	BR[8] w	BR[7] w	BR[6] w	BR[5] w	BR[4] w	BR[3] w	BR[2] w	BR[1] w	BR[0] w

Toggle fields

BR[0]

Bit 0: Port x reset pin 0.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[1]

Bit 1: Port x reset pin 1.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[2]

Bit 2: Port x reset pin 2.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[3]

Bit 3: Port x reset pin 3.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[4]

Bit 4: Port x reset pin 4.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[5]

Bit 5: Port x reset pin 5.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[6]

Bit 6: Port x reset pin 6.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[7]

Bit 7: Port x reset pin 7.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[8]

Bit 8: Port x reset pin 8.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[9]

Bit 9: Port x reset pin 9.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[10]

Bit 10: Port x reset pin 10.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[11]

Bit 11: Port x reset pin 11.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[12]

Bit 12: Port x reset pin 12.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[13]

Bit 13: Port x reset pin 13.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[14]

Bit 14: Port x reset pin 14.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[15]

Bit 15: Port x reset pin 15.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

GPIOH

0x48001c00: General-purpose I/Os

177/177 fields covered.

Toggle register map

Offset	Name	31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	MODER	MODER[15]		MODER[14]		MODER[13]		MODER[12]		MODER[11]		MODER[10]		MODER[9]		MODER[8]		MODER[7]		MODER[6]		MODER[5]		MODER[4]		MODER[3]		MODER[2]		MODER[1]		MODER[0]
0x4	OTYPER																	OT[15]	OT[14]	OT[13]	OT[12]	OT[11]	OT[10]	OT[9]	OT[8]	OT[7]	OT[6]	OT[5]	OT[4]	OT[3]	OT[2]	OT[1]	OT[0]
0x8	OSPEEDR	OSPEEDR[15]		OSPEEDR[14]		OSPEEDR[13]		OSPEEDR[12]		OSPEEDR[11]		OSPEEDR[10]		OSPEEDR[9]		OSPEEDR[8]		OSPEEDR[7]		OSPEEDR[6]		OSPEEDR[5]		OSPEEDR[4]		OSPEEDR[3]		OSPEEDR[2]		OSPEEDR[1]		OSPEEDR[0]
0xc	PUPDR	PUPDR[15]		PUPDR[14]		PUPDR[13]		PUPDR[12]		PUPDR[11]		PUPDR[10]		PUPDR[9]		PUPDR[8]		PUPDR[7]		PUPDR[6]		PUPDR[5]		PUPDR[4]		PUPDR[3]		PUPDR[2]		PUPDR[1]		PUPDR[0]
0x10	IDR																	IDR[15]	IDR[14]	IDR[13]	IDR[12]	IDR[11]	IDR[10]	IDR[9]	IDR[8]	IDR[7]	IDR[6]	IDR[5]	IDR[4]	IDR[3]	IDR[2]	IDR[1]	IDR[0]
0x14	ODR																	ODR[15]	ODR[14]	ODR[13]	ODR[12]	ODR[11]	ODR[10]	ODR[9]	ODR[8]	ODR[7]	ODR[6]	ODR[5]	ODR[4]	ODR[3]	ODR[2]	ODR[1]	ODR[0]
0x18	BSRR	BR[15]	BR[14]	BR[13]	BR[12]	BR[11]	BR[10]	BR[9]	BR[8]	BR[7]	BR[6]	BR[5]	BR[4]	BR[3]	BR[2]	BR[1]	BR[0]	BS[15]	BS[14]	BS[13]	BS[12]	BS[11]	BS[10]	BS[9]	BS[8]	BS[7]	BS[6]	BS[5]	BS[4]	BS[3]	BS[2]	BS[1]	BS[0]
0x1c	LCKR																LCKK	LCK[15]	LCK[14]	LCK[13]	LCK[12]	LCK[11]	LCK[10]	LCK[9]	LCK[8]	LCK[7]	LCK[6]	LCK[5]	LCK[4]	LCK[3]	LCK[2]	LCK[1]	LCK[0]
0x20	AFRL	AFR[L7]				AFR[L6]				AFR[L5]				AFR[L4]				AFR[L3]				AFR[L2]				AFR[L1]				AFR[L0]
0x24	AFRH	AFR[H15]				AFR[H14]				AFR[H13]				AFR[H12]				AFR[H11]				AFR[H10]				AFR[H9]				AFR[H8]
0x28	BRR																	BR[15]	BR[14]	BR[13]	BR[12]	BR[11]	BR[10]	BR[9]	BR[8]	BR[7]	BR[6]	BR[5]	BR[4]	BR[3]	BR[2]	BR[1]	BR[0]

Toggle registers

MODER

GPIO port mode register

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MODER[15] rw		MODER[14] rw		MODER[13] rw		MODER[12] rw		MODER[11] rw		MODER[10] rw		MODER[9] rw		MODER[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MODER[7] rw		MODER[6] rw		MODER[5] rw		MODER[4] rw		MODER[3] rw		MODER[2] rw		MODER[1] rw		MODER[0] rw

Toggle fields

MODER[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

OTYPER

GPIO port output type register

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OT[15] rw	OT[14] rw	OT[13] rw	OT[12] rw	OT[11] rw	OT[10] rw	OT[9] rw	OT[8] rw	OT[7] rw	OT[6] rw	OT[5] rw	OT[4] rw	OT[3] rw	OT[2] rw	OT[1] rw	OT[0] rw

Toggle fields

OT[0]

Bit 0: Port x configuration pin 0.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[1]

Bit 1: Port x configuration pin 1.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[2]

Bit 2: Port x configuration pin 2.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[3]

Bit 3: Port x configuration pin 3.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[4]

Bit 4: Port x configuration pin 4.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[5]

Bit 5: Port x configuration pin 5.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[6]

Bit 6: Port x configuration pin 6.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[7]

Bit 7: Port x configuration pin 7.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[8]

Bit 8: Port x configuration pin 8.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[9]

Bit 9: Port x configuration pin 9.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[10]

Bit 10: Port x configuration pin 10.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[11]

Bit 11: Port x configuration pin 11.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[12]

Bit 12: Port x configuration pin 12.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[13]

Bit 13: Port x configuration pin 13.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[14]

Bit 14: Port x configuration pin 14.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[15]

Bit 15: Port x configuration pin 15.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OSPEEDR

GPIO port output speed register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OSPEEDR[15] rw		OSPEEDR[14] rw		OSPEEDR[13] rw		OSPEEDR[12] rw		OSPEEDR[11] rw		OSPEEDR[10] rw		OSPEEDR[9] rw		OSPEEDR[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OSPEEDR[7] rw		OSPEEDR[6] rw		OSPEEDR[5] rw		OSPEEDR[4] rw		OSPEEDR[3] rw		OSPEEDR[2] rw		OSPEEDR[1] rw		OSPEEDR[0] rw

Toggle fields

OSPEEDR[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

OSPEEDR[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
3: HighSpeed: High speed

PUPDR

GPIO port pull-up/pull-down register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PUPDR[15] rw		PUPDR[14] rw		PUPDR[13] rw		PUPDR[12] rw		PUPDR[11] rw		PUPDR[10] rw		PUPDR[9] rw		PUPDR[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PUPDR[7] rw		PUPDR[6] rw		PUPDR[5] rw		PUPDR[4] rw		PUPDR[3] rw		PUPDR[2] rw		PUPDR[1] rw		PUPDR[0] rw

Toggle fields

PUPDR[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

IDR

GPIO port input data register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-only

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IDR[15] r	IDR[14] r	IDR[13] r	IDR[12] r	IDR[11] r	IDR[10] r	IDR[9] r	IDR[8] r	IDR[7] r	IDR[6] r	IDR[5] r	IDR[4] r	IDR[3] r	IDR[2] r	IDR[1] r	IDR[0] r

Toggle fields

IDR[0]

Bit 0: Port input data pin 0.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[1]

Bit 1: Port input data pin 1.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[2]

Bit 2: Port input data pin 2.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[3]

Bit 3: Port input data pin 3.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[4]

Bit 4: Port input data pin 4.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[5]

Bit 5: Port input data pin 5.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[6]

Bit 6: Port input data pin 6.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[7]

Bit 7: Port input data pin 7.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[8]

Bit 8: Port input data pin 8.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[9]

Bit 9: Port input data pin 9.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[10]

Bit 10: Port input data pin 10.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[11]

Bit 11: Port input data pin 11.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[12]

Bit 12: Port input data pin 12.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[13]

Bit 13: Port input data pin 13.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[14]

Bit 14: Port input data pin 14.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[15]

Bit 15: Port input data pin 15.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

ODR

GPIO port output data register

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ODR[15] rw	ODR[14] rw	ODR[13] rw	ODR[12] rw	ODR[11] rw	ODR[10] rw	ODR[9] rw	ODR[8] rw	ODR[7] rw	ODR[6] rw	ODR[5] rw	ODR[4] rw	ODR[3] rw	ODR[2] rw	ODR[1] rw	ODR[0] rw

Toggle fields

ODR[0]

Bit 0: Port output data pin 0.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[1]

Bit 1: Port output data pin 1.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[2]

Bit 2: Port output data pin 2.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[3]

Bit 3: Port output data pin 3.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[4]

Bit 4: Port output data pin 4.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[5]

Bit 5: Port output data pin 5.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[6]

Bit 6: Port output data pin 6.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[7]

Bit 7: Port output data pin 7.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[8]

Bit 8: Port output data pin 8.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[9]

Bit 9: Port output data pin 9.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[10]

Bit 10: Port output data pin 10.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[11]

Bit 11: Port output data pin 11.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[12]

Bit 12: Port output data pin 12.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[13]

Bit 13: Port output data pin 13.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[14]

Bit 14: Port output data pin 14.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[15]

Bit 15: Port output data pin 15.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

BSRR

GPIO port bit set/reset register

Offset: 0x18, size: 32, reset: 0x00000000, access: write-only

32/32 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BR[15] w	BR[14] w	BR[13] w	BR[12] w	BR[11] w	BR[10] w	BR[9] w	BR[8] w	BR[7] w	BR[6] w	BR[5] w	BR[4] w	BR[3] w	BR[2] w	BR[1] w	BR[0] w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BS[15] w	BS[14] w	BS[13] w	BS[12] w	BS[11] w	BS[10] w	BS[9] w	BS[8] w	BS[7] w	BS[6] w	BS[5] w	BS[4] w	BS[3] w	BS[2] w	BS[1] w	BS[0] w

Toggle fields

BS[0]

Bit 0: Port x set pin 0.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[1]

Bit 1: Port x set pin 1.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[2]

Bit 2: Port x set pin 2.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[3]

Bit 3: Port x set pin 3.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[4]

Bit 4: Port x set pin 4.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[5]

Bit 5: Port x set pin 5.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[6]

Bit 6: Port x set pin 6.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[7]

Bit 7: Port x set pin 7.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[8]

Bit 8: Port x set pin 8.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[9]

Bit 9: Port x set pin 9.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[10]

Bit 10: Port x set pin 10.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[11]

Bit 11: Port x set pin 11.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[12]

Bit 12: Port x set pin 12.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[13]

Bit 13: Port x set pin 13.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[14]

Bit 14: Port x set pin 14.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS[15]

Bit 15: Port x set pin 15.

Allowed values:
1: Set: Sets the corresponding ODRx bit

BR[0]

Bit 16: Port x reset pin 0.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[1]

Bit 17: Port x reset pin 1.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[2]

Bit 18: Port x reset pin 2.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[3]

Bit 19: Port x reset pin 3.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[4]

Bit 20: Port x reset pin 4.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[5]

Bit 21: Port x reset pin 5.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[6]

Bit 22: Port x reset pin 6.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[7]

Bit 23: Port x reset pin 7.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[8]

Bit 24: Port x reset pin 8.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[9]

Bit 25: Port x reset pin 9.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[10]

Bit 26: Port x reset pin 10.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[11]

Bit 27: Port x reset pin 11.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[12]

Bit 28: Port x reset pin 12.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[13]

Bit 29: Port x reset pin 13.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[14]

Bit 30: Port x reset pin 14.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR[15]

Bit 31: Port x reset pin 15.

Allowed values:
1: Reset: Resets the corresponding ODRx bit

LCKR

GPIO port configuration lock register

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

17/17 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															LCKK rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
LCK[15] rw	LCK[14] rw	LCK[13] rw	LCK[12] rw	LCK[11] rw	LCK[10] rw	LCK[9] rw	LCK[8] rw	LCK[7] rw	LCK[6] rw	LCK[5] rw	LCK[4] rw	LCK[3] rw	LCK[2] rw	LCK[1] rw	LCK[0] rw

Toggle fields

LCK[0]

Bit 0: Port x lock pin 0.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[1]

Bit 1: Port x lock pin 1.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[2]

Bit 2: Port x lock pin 2.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[3]

Bit 3: Port x lock pin 3.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[4]

Bit 4: Port x lock pin 4.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[5]

Bit 5: Port x lock pin 5.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[6]

Bit 6: Port x lock pin 6.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[7]

Bit 7: Port x lock pin 7.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[8]

Bit 8: Port x lock pin 8.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[9]

Bit 9: Port x lock pin 9.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[10]

Bit 10: Port x lock pin 10.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[11]

Bit 11: Port x lock pin 11.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[12]

Bit 12: Port x lock pin 12.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[13]

Bit 13: Port x lock pin 13.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[14]

Bit 14: Port x lock pin 14.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[15]

Bit 15: Port x lock pin 15.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCKK

Bit 16: Lok Key.

Allowed values:
0: NotActive: Port configuration lock key not active
1: Active: Port configuration lock key active

AFRL

GPIO alternate function low register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AFR[L7] rw				AFR[L6] rw				AFR[L5] rw				AFR[L4] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AFR[L3] rw				AFR[L2] rw				AFR[L1] rw				AFR[L0] rw

Toggle fields

AFR[L0]

Bits 0-3: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L1]

Bits 4-7: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L2]

Bits 8-11: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L3]

Bits 12-15: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L4]

Bits 16-19: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L5]

Bits 20-23: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L6]

Bits 24-27: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[L7]

Bits 28-31: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRH

GPIO alternate function high register

Offset: 0x24, size: 32, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AFR[H15] rw				AFR[H14] rw				AFR[H13] rw				AFR[H12] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AFR[H11] rw				AFR[H10] rw				AFR[H9] rw				AFR[H8] rw

Toggle fields

AFR[H8]

Bits 0-3: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H9]

Bits 4-7: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H10]

Bits 8-11: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H11]

Bits 12-15: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H12]

Bits 16-19: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H13]

Bits 20-23: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H14]

Bits 24-27: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFR[H15]

Bits 28-31: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

BRR

Port bit reset register

Offset: 0x28, size: 32, reset: 0x00000000, access: write-only

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BR[15] w	BR[14] w	BR[13] w	BR[12] w	BR[11] w	BR[10] w	BR[9] w	BR[8] w	BR[7] w	BR[6] w	BR[5] w	BR[4] w	BR[3] w	BR[2] w	BR[1] w	BR[0] w

Toggle fields

BR[0]

Bit 0: Port x reset pin 0.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[1]

Bit 1: Port x reset pin 1.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[2]

Bit 2: Port x reset pin 2.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[3]

Bit 3: Port x reset pin 3.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[4]

Bit 4: Port x reset pin 4.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[5]

Bit 5: Port x reset pin 5.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[6]

Bit 6: Port x reset pin 6.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[7]

Bit 7: Port x reset pin 7.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[8]

Bit 8: Port x reset pin 8.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[9]

Bit 9: Port x reset pin 9.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[10]

Bit 10: Port x reset pin 10.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[11]

Bit 11: Port x reset pin 11.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[12]

Bit 12: Port x reset pin 12.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[13]

Bit 13: Port x reset pin 13.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[14]

Bit 14: Port x reset pin 14.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[15]

Bit 15: Port x reset pin 15.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

I2C1

0x40005400: Inter-integrated circuit

76/77 fields covered.

Toggle register map

Offset	Name	31	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	CR1						PECEN	ALERTEN	SMBDEN	SMBHEN	GCEN	WUPEN	NOSTRETCH	SBC	RXDMAEN	TXDMAEN	SWRST	ANFOFF	DNF				ERRIE	TCIE	STOPIE	NACKIE	ADDRIE	RXIE	TXIE	PE
0x4	CR2			PECBYTE	AUTOEND	RELOAD	NBYTES								NACK	STOP	START	HEAD10R	ADD10	RD_WRN	SADD
0x8	OAR1														OA1EN					OA1MODE	OA1
0xc	OAR2														OA2EN					OA2MSK			OA2
0x10	TIMINGR	PRESC					SCLDEL				SDADEL				SCLH								SCLL
0x14	TIMEOUTR	TEXTEN	TIMEOUTB												TIMOUTEN			TIDLE	TIMEOUTA
0x18	ISR						ADDCODE							DIR	BUSY		ALERT	TIMEOUT	PECERR	OVR	ARLO	BERR	TCR	TC	STOPF	NACKF	ADDR	RXNE	TXIS	TXE
0x1c	ICR																ALERTCF	TIMOUTCF	PECCF	OVRCF	ARLOCF	BERRCF			STOPCF	NACKCF	ADDRCF
0x20	PECR																						PEC
0x24	RXDR																						RXDATA
0x28	TXDR																						TXDATA

Toggle registers

CR1

Control register 1

Offset: 0x0, size: 32, reset: 0x00000000, access: Unspecified

20/21 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								PECEN rw	ALERTEN rw	SMBDEN rw	SMBHEN rw	GCEN rw	WUPEN rw	NOSTRETCH rw	SBC rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RXDMAEN rw	TXDMAEN rw	SWRST w	ANFOFF rw	DNF rw				ERRIE rw	TCIE rw	STOPIE rw	NACKIE rw	ADDRIE rw	RXIE rw	TXIE rw	PE rw

Toggle fields

PE

Bit 0: Peripheral enable.

Allowed values:
0: Disabled: Peripheral disabled
1: Enabled: Peripheral enabled

TXIE

Bit 1: TX Interrupt enable.

Allowed values:
0: Disabled: Transmit (TXIS) interrupt disabled
1: Enabled: Transmit (TXIS) interrupt enabled

RXIE

Bit 2: RX Interrupt enable.

Allowed values:
0: Disabled: Receive (RXNE) interrupt disabled
1: Enabled: Receive (RXNE) interrupt enabled

ADDRIE

Bit 3: Address match interrupt enable (slave only).

Allowed values:
0: Disabled: Address match (ADDR) interrupts disabled
1: Enabled: Address match (ADDR) interrupts enabled

NACKIE

Bit 4: Not acknowledge received interrupt enable.

Allowed values:
0: Disabled: Not acknowledge (NACKF) received interrupts disabled
1: Enabled: Not acknowledge (NACKF) received interrupts enabled

STOPIE

Bit 5: STOP detection Interrupt enable.

Allowed values:
0: Disabled: Stop detection (STOPF) interrupt disabled
1: Enabled: Stop detection (STOPF) interrupt enabled

TCIE

Bit 6: Transfer Complete interrupt enable.

Allowed values:
0: Disabled: Transfer Complete interrupt disabled
1: Enabled: Transfer Complete interrupt enabled

ERRIE

Bit 7: Error interrupts enable.

Allowed values:
0: Disabled: Error detection interrupts disabled
1: Enabled: Error detection interrupts enabled

DNF

Bits 8-11: Digital noise filter.

Allowed values:
0: NoFilter: Digital filter disabled
1: Filter1: Digital filter enabled and filtering capability up to 1 tI2CCLK
2: Filter2: Digital filter enabled and filtering capability up to 2 tI2CCLK
3: Filter3: Digital filter enabled and filtering capability up to 3 tI2CCLK
4: Filter4: Digital filter enabled and filtering capability up to 4 tI2CCLK
5: Filter5: Digital filter enabled and filtering capability up to 5 tI2CCLK
6: Filter6: Digital filter enabled and filtering capability up to 6 tI2CCLK
7: Filter7: Digital filter enabled and filtering capability up to 7 tI2CCLK
8: Filter8: Digital filter enabled and filtering capability up to 8 tI2CCLK
9: Filter9: Digital filter enabled and filtering capability up to 9 tI2CCLK
10: Filter10: Digital filter enabled and filtering capability up to 10 tI2CCLK
11: Filter11: Digital filter enabled and filtering capability up to 11 tI2CCLK
12: Filter12: Digital filter enabled and filtering capability up to 12 tI2CCLK
13: Filter13: Digital filter enabled and filtering capability up to 13 tI2CCLK
14: Filter14: Digital filter enabled and filtering capability up to 14 tI2CCLK
15: Filter15: Digital filter enabled and filtering capability up to 15 tI2CCLK

ANFOFF

Bit 12: Analog noise filter OFF.

Allowed values:
0: Enabled: Analog noise filter enabled
1: Disabled: Analog noise filter disabled

SWRST

Bit 13: Software reset.

TXDMAEN

Bit 14: DMA transmission requests enable.

Allowed values:
0: Disabled: DMA mode disabled for transmission
1: Enabled: DMA mode enabled for transmission

RXDMAEN

Bit 15: DMA reception requests enable.

Allowed values:
0: Disabled: DMA mode disabled for reception
1: Enabled: DMA mode enabled for reception

SBC

Bit 16: Slave byte control.

Allowed values:
0: Disabled: Slave byte control disabled
1: Enabled: Slave byte control enabled

NOSTRETCH

Bit 17: Clock stretching disable.

Allowed values:
0: Enabled: Clock stretching enabled
1: Disabled: Clock stretching disabled

WUPEN

Bit 18: Wakeup from STOP enable.

Allowed values:
0: Disabled: Wakeup from Stop mode disabled
1: Enabled: Wakeup from Stop mode enabled

GCEN

Bit 19: General call enable.

Allowed values:
0: Disabled: General call disabled. Address 0b00000000 is NACKed
1: Enabled: General call enabled. Address 0b00000000 is ACKed

SMBHEN

Bit 20: SMBus Host address enable.

Allowed values:
0: Disabled: Host address disabled. Address 0b0001000x is NACKed
1: Enabled: Host address enabled. Address 0b0001000x is ACKed

SMBDEN

Bit 21: SMBus Device Default address enable.

Allowed values:
0: Disabled: Device default address disabled. Address 0b1100001x is NACKed
1: Enabled: Device default address enabled. Address 0b1100001x is ACKed

ALERTEN

Bit 22: SMBUS alert enable.

Allowed values:
0: Disabled: In device mode (SMBHEN=Disabled) Releases SMBA pin high and Alert Response Address Header disabled (0001100x) followed by NACK. In host mode (SMBHEN=Enabled) SMBus Alert pin (SMBA) not supported
1: Enabled: In device mode (SMBHEN=Disabled) Drives SMBA pin low and Alert Response Address Header enabled (0001100x) followed by ACK.In host mode (SMBHEN=Enabled) SMBus Alert pin (SMBA) supported

PECEN

Bit 23: PEC enable.

Allowed values:
0: Disabled: PEC calculation disabled
1: Enabled: PEC calculation enabled

CR2

Control register 2

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

11/11 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
					PECBYTE rw	AUTOEND rw	RELOAD rw	NBYTES rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
NACK rw	STOP rw	START rw	HEAD10R rw	ADD10 rw	RD_WRN rw	SADD rw

Toggle fields

SADD

Bits 0-9: Slave address bit 9:8 (master mode).

Allowed values: 0x0-0x3ff

RD_WRN

Bit 10: Transfer direction (master mode).

Allowed values:
0: Write: Master requests a write transfer
1: Read: Master requests a read transfer

ADD10

Bit 11: 10-bit addressing mode (master mode).

Allowed values:
0: Bit7: The master operates in 7-bit addressing mode
1: Bit10: The master operates in 10-bit addressing mode

HEAD10R

Bit 12: 10-bit address header only read direction (master receiver mode).

Allowed values:
0: Complete: The master sends the complete 10 bit slave address read sequence
1: Partial: The master only sends the 1st 7 bits of the 10 bit address, followed by Read direction

START

Bit 13: Start generation.

Allowed values:
0: NoStart: No Start generation
1: Start: Restart/Start generation

STOP

Bit 14: Stop generation (master mode).

Allowed values:
0: NoStop: No Stop generation
1: Stop: Stop generation after current byte transfer

NACK

Bit 15: NACK generation (slave mode).

Allowed values:
0: Ack: an ACK is sent after current received byte
1: Nack: a NACK is sent after current received byte

NBYTES

Bits 16-23: Number of bytes.

Allowed values: 0x0-0xff

RELOAD

Bit 24: NBYTES reload mode.

Allowed values:
0: Completed: The transfer is completed after the NBYTES data transfer (STOP or RESTART will follow)
1: NotCompleted: The transfer is not completed after the NBYTES data transfer (NBYTES will be reloaded)

AUTOEND

Bit 25: Automatic end mode (master mode).

Allowed values:
0: Software: Software end mode: TC flag is set when NBYTES data are transferred, stretching SCL low
1: Automatic: Automatic end mode: a STOP condition is automatically sent when NBYTES data are transferred

PECBYTE

Bit 26: Packet error checking byte.

Allowed values:
0: NoPec: No PEC transfer
1: Pec: PEC transmission/reception is requested

OAR1

Own address register 1

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

3/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OA1EN rw					OA1MODE rw	OA1 rw

Toggle fields

OA1

Bits 0-9: Interface address.

Allowed values: 0x0-0x3ff

OA1MODE

Bit 10: Own Address 1 10-bit mode.

Allowed values:
0: Bit7: Own address 1 is a 7-bit address
1: Bit10: Own address 1 is a 10-bit address

OA1EN

Bit 15: Own Address 1 enable.

Allowed values:
0: Disabled: Own address 1 disabled. The received slave address OA1 is NACKed
1: Enabled: Own address 1 enabled. The received slave address OA1 is ACKed

OAR2

Own address register 2

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

3/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OA2EN rw					OA2MSK rw			OA2 rw

Toggle fields

OA2

Bits 1-7: Interface address.

Allowed values: 0x0-0x7f

OA2MSK

Bits 8-10: Own Address 2 masks.

Allowed values:
0: NoMask: No mask
1: Mask1: OA2[1] is masked and don’t care. Only OA2[7:2] are compared
2: Mask2: OA2[2:1] are masked and don’t care. Only OA2[7:3] are compared
3: Mask3: OA2[3:1] are masked and don’t care. Only OA2[7:4] are compared
4: Mask4: OA2[4:1] are masked and don’t care. Only OA2[7:5] are compared
5: Mask5: OA2[5:1] are masked and don’t care. Only OA2[7:6] are compared
6: Mask6: OA2[6:1] are masked and don’t care. Only OA2[7] is compared.
7: Mask7: OA2[7:1] are masked and don’t care. No comparison is done, and all (except reserved) 7-bit received addresses are acknowledged

OA2EN

Bit 15: Own Address 2 enable.

Allowed values:
0: Disabled: Own address 2 disabled. The received slave address OA2 is NACKed
1: Enabled: Own address 2 enabled. The received slave address OA2 is ACKed

TIMINGR

Timing register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PRESC rw								SCLDEL rw				SDADEL rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SCLH rw								SCLL rw

Toggle fields

SCLL

Bits 0-7: SCL low period (master mode).

Allowed values: 0x0-0xff

SCLH

Bits 8-15: SCL high period (master mode).

Allowed values: 0x0-0xff

SDADEL

Bits 16-19: Data hold time.

Allowed values: 0x0-0xf

SCLDEL

Bits 20-23: Data setup time.

Allowed values: 0x0-0xf

PRESC

Bits 28-31: Timing prescaler.

Allowed values: 0x0-0xf

TIMEOUTR

Status register 1

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
TEXTEN rw				TIMEOUTB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TIMOUTEN rw			TIDLE rw	TIMEOUTA rw

Toggle fields

TIMEOUTA

Bits 0-11: Bus timeout A.

Allowed values: 0x0-0xfff

TIDLE

Bit 12: Idle clock timeout detection.

Allowed values:
0: Disabled: TIMEOUTA is used to detect SCL low timeout
1: Enabled: TIMEOUTA is used to detect both SCL and SDA high timeout (bus idle condition)

TIMOUTEN

Bit 15: Clock timeout enable.

Allowed values:
0: Disabled: SCL timeout detection is disabled
1: Enabled: SCL timeout detection is enabled

TIMEOUTB

Bits 16-27: Bus timeout B.

Allowed values: 0x0-0xfff

TEXTEN

Bit 31: Extended clock timeout enable.

Allowed values:
0: Disabled: Extended clock timeout detection is disabled
1: Enabled: Extended clock timeout detection is enabled

ISR

Interrupt and Status register

Offset: 0x18, size: 32, reset: 0x00000001, access: Unspecified

17/17 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								ADDCODE r							DIR r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BUSY r		ALERT r	TIMEOUT r	PECERR r	OVR r	ARLO r	BERR r	TCR r	TC r	STOPF r	NACKF r	ADDR r	RXNE r	TXIS rw	TXE rw

Toggle fields

TXE

Bit 0: Transmit data register empty (transmitters).

Allowed values:
0: NotEmpty: TXDR register not empty
1: Empty: TXDR register empty

TXIS

Bit 1: Transmit interrupt status (transmitters).

Allowed values:
0: NotEmpty: The TXDR register is not empty
1: Empty: The TXDR register is empty and the data to be transmitted must be written in the TXDR register

RXNE

Bit 2: Receive data register not empty (receivers).

Allowed values:
0: Empty: The RXDR register is empty
1: NotEmpty: Received data is copied into the RXDR register, and is ready to be read

ADDR

Bit 3: Address matched (slave mode).

Allowed values:
0: NotMatch: Adress mismatched or not received
1: Match: Received slave address matched with one of the enabled slave addresses

NACKF

Bit 4: Not acknowledge received flag.

Allowed values:
0: NoNack: No NACK has been received
1: Nack: NACK has been received

STOPF

Bit 5: Stop detection flag.

Allowed values:
0: NoStop: No Stop condition detected
1: Stop: Stop condition detected

TC

Bit 6: Transfer Complete (master mode).

Allowed values:
0: NotComplete: Transfer is not complete
1: Complete: NBYTES has been transfered

TCR

Bit 7: Transfer Complete Reload.

Allowed values:
0: NotComplete: Transfer is not complete
1: Complete: NBYTES has been transfered

BERR

Bit 8: Bus error.

Allowed values:
0: NoError: No bus error
1: Error: Misplaced Start and Stop condition is detected

ARLO

Bit 9: Arbitration lost.

Allowed values:
0: NotLost: No arbitration lost
1: Lost: Arbitration lost

OVR

Bit 10: Overrun/Underrun (slave mode).

Allowed values:
0: NoOverrun: No overrun/underrun error occurs
1: Overrun: slave mode with NOSTRETCH=1, when an overrun/underrun error occurs

PECERR

Bit 11: PEC Error in reception.

Allowed values:
0: Match: Received PEC does match with PEC register
1: NoMatch: Received PEC does not match with PEC register

TIMEOUT

Bit 12: Timeout or t_low detection flag.

Allowed values:
0: NoTimeout: No timeout occured
1: Timeout: Timeout occured

ALERT

Bit 13: SMBus alert.

Allowed values:
0: NoAlert: SMBA alert is not detected
1: Alert: SMBA alert event is detected on SMBA pin

BUSY

Bit 15: Bus busy.

Allowed values:
0: NotBusy: No communication is in progress on the bus
1: Busy: A communication is in progress on the bus

DIR

Bit 16: Transfer direction (Slave mode).

Allowed values:
0: Write: Write transfer, slave enters receiver mode
1: Read: Read transfer, slave enters transmitter mode

ADDCODE

Bits 17-23: Address match code (Slave mode).

Allowed values: 0x0-0x7f

ICR

Interrupt clear register

Offset: 0x1c, size: 32, reset: 0x00000000, access: write-only

9/9 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		ALERTCF w	TIMOUTCF w	PECCF w	OVRCF w	ARLOCF w	BERRCF w			STOPCF w	NACKCF w	ADDRCF w

Toggle fields

ADDRCF

Bit 3: Address Matched flag clear.

Allowed values:
1: Clear: Clears the ADDR flag in ISR register

NACKCF

Bit 4: Not Acknowledge flag clear.

Allowed values:
1: Clear: Clears the NACK flag in ISR register

STOPCF

Bit 5: Stop detection flag clear.

Allowed values:
1: Clear: Clears the STOP flag in ISR register

BERRCF

Bit 8: Bus error flag clear.

Allowed values:
1: Clear: Clears the BERR flag in ISR register

ARLOCF

Bit 9: Arbitration lost flag clear.

Allowed values:
1: Clear: Clears the ARLO flag in ISR register

OVRCF

Bit 10: Overrun/Underrun flag clear.

Allowed values:
1: Clear: Clears the OVR flag in ISR register

PECCF

Bit 11: PEC Error flag clear.

Allowed values:
1: Clear: Clears the PEC flag in ISR register

TIMOUTCF

Bit 12: Timeout detection flag clear.

Allowed values:
1: Clear: Clears the TIMOUT flag in ISR register

ALERTCF

Bit 13: Alert flag clear.

Allowed values:
1: Clear: Clears the ALERT flag in ISR register

PECR

PEC register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								PEC r

Toggle fields

PEC

Bits 0-7: Packet error checking register.

Allowed values: 0x0-0xff

RXDR

Receive data register

Offset: 0x24, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								RXDATA r

Toggle fields

RXDATA

Bits 0-7: 8-bit receive data.

Allowed values: 0x0-0xff

TXDR

Transmit data register

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								TXDATA rw

Toggle fields

TXDATA

Bits 0-7: 8-bit transmit data.

Allowed values: 0x0-0xff

I2C2

0x40005800: Inter-integrated circuit

76/77 fields covered.

Toggle register map

Offset	Name	31	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	CR1						PECEN	ALERTEN	SMBDEN	SMBHEN	GCEN	WUPEN	NOSTRETCH	SBC	RXDMAEN	TXDMAEN	SWRST	ANFOFF	DNF				ERRIE	TCIE	STOPIE	NACKIE	ADDRIE	RXIE	TXIE	PE
0x4	CR2			PECBYTE	AUTOEND	RELOAD	NBYTES								NACK	STOP	START	HEAD10R	ADD10	RD_WRN	SADD
0x8	OAR1														OA1EN					OA1MODE	OA1
0xc	OAR2														OA2EN					OA2MSK			OA2
0x10	TIMINGR	PRESC					SCLDEL				SDADEL				SCLH								SCLL
0x14	TIMEOUTR	TEXTEN	TIMEOUTB												TIMOUTEN			TIDLE	TIMEOUTA
0x18	ISR						ADDCODE							DIR	BUSY		ALERT	TIMEOUT	PECERR	OVR	ARLO	BERR	TCR	TC	STOPF	NACKF	ADDR	RXNE	TXIS	TXE
0x1c	ICR																ALERTCF	TIMOUTCF	PECCF	OVRCF	ARLOCF	BERRCF			STOPCF	NACKCF	ADDRCF
0x20	PECR																						PEC
0x24	RXDR																						RXDATA
0x28	TXDR																						TXDATA

Toggle registers

CR1

Control register 1

Offset: 0x0, size: 32, reset: 0x00000000, access: Unspecified

20/21 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								PECEN rw	ALERTEN rw	SMBDEN rw	SMBHEN rw	GCEN rw	WUPEN rw	NOSTRETCH rw	SBC rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RXDMAEN rw	TXDMAEN rw	SWRST w	ANFOFF rw	DNF rw				ERRIE rw	TCIE rw	STOPIE rw	NACKIE rw	ADDRIE rw	RXIE rw	TXIE rw	PE rw

Toggle fields

PE

Bit 0: Peripheral enable.

Allowed values:
0: Disabled: Peripheral disabled
1: Enabled: Peripheral enabled

TXIE

Bit 1: TX Interrupt enable.

Allowed values:
0: Disabled: Transmit (TXIS) interrupt disabled
1: Enabled: Transmit (TXIS) interrupt enabled

RXIE

Bit 2: RX Interrupt enable.

Allowed values:
0: Disabled: Receive (RXNE) interrupt disabled
1: Enabled: Receive (RXNE) interrupt enabled

ADDRIE

Bit 3: Address match interrupt enable (slave only).

Allowed values:
0: Disabled: Address match (ADDR) interrupts disabled
1: Enabled: Address match (ADDR) interrupts enabled

NACKIE

Bit 4: Not acknowledge received interrupt enable.

Allowed values:
0: Disabled: Not acknowledge (NACKF) received interrupts disabled
1: Enabled: Not acknowledge (NACKF) received interrupts enabled

STOPIE

Bit 5: STOP detection Interrupt enable.

Allowed values:
0: Disabled: Stop detection (STOPF) interrupt disabled
1: Enabled: Stop detection (STOPF) interrupt enabled

TCIE

Bit 6: Transfer Complete interrupt enable.

Allowed values:
0: Disabled: Transfer Complete interrupt disabled
1: Enabled: Transfer Complete interrupt enabled

ERRIE

Bit 7: Error interrupts enable.

Allowed values:
0: Disabled: Error detection interrupts disabled
1: Enabled: Error detection interrupts enabled

DNF

Bits 8-11: Digital noise filter.

Allowed values:
0: NoFilter: Digital filter disabled
1: Filter1: Digital filter enabled and filtering capability up to 1 tI2CCLK
2: Filter2: Digital filter enabled and filtering capability up to 2 tI2CCLK
3: Filter3: Digital filter enabled and filtering capability up to 3 tI2CCLK
4: Filter4: Digital filter enabled and filtering capability up to 4 tI2CCLK
5: Filter5: Digital filter enabled and filtering capability up to 5 tI2CCLK
6: Filter6: Digital filter enabled and filtering capability up to 6 tI2CCLK
7: Filter7: Digital filter enabled and filtering capability up to 7 tI2CCLK
8: Filter8: Digital filter enabled and filtering capability up to 8 tI2CCLK
9: Filter9: Digital filter enabled and filtering capability up to 9 tI2CCLK
10: Filter10: Digital filter enabled and filtering capability up to 10 tI2CCLK
11: Filter11: Digital filter enabled and filtering capability up to 11 tI2CCLK
12: Filter12: Digital filter enabled and filtering capability up to 12 tI2CCLK
13: Filter13: Digital filter enabled and filtering capability up to 13 tI2CCLK
14: Filter14: Digital filter enabled and filtering capability up to 14 tI2CCLK
15: Filter15: Digital filter enabled and filtering capability up to 15 tI2CCLK

ANFOFF

Bit 12: Analog noise filter OFF.

Allowed values:
0: Enabled: Analog noise filter enabled
1: Disabled: Analog noise filter disabled

SWRST

Bit 13: Software reset.

TXDMAEN

Bit 14: DMA transmission requests enable.

Allowed values:
0: Disabled: DMA mode disabled for transmission
1: Enabled: DMA mode enabled for transmission

RXDMAEN

Bit 15: DMA reception requests enable.

Allowed values:
0: Disabled: DMA mode disabled for reception
1: Enabled: DMA mode enabled for reception

SBC

Bit 16: Slave byte control.

Allowed values:
0: Disabled: Slave byte control disabled
1: Enabled: Slave byte control enabled

NOSTRETCH

Bit 17: Clock stretching disable.

Allowed values:
0: Enabled: Clock stretching enabled
1: Disabled: Clock stretching disabled

WUPEN

Bit 18: Wakeup from STOP enable.

Allowed values:
0: Disabled: Wakeup from Stop mode disabled
1: Enabled: Wakeup from Stop mode enabled

GCEN

Bit 19: General call enable.

Allowed values:
0: Disabled: General call disabled. Address 0b00000000 is NACKed
1: Enabled: General call enabled. Address 0b00000000 is ACKed

SMBHEN

Bit 20: SMBus Host address enable.

Allowed values:
0: Disabled: Host address disabled. Address 0b0001000x is NACKed
1: Enabled: Host address enabled. Address 0b0001000x is ACKed

SMBDEN

Bit 21: SMBus Device Default address enable.

Allowed values:
0: Disabled: Device default address disabled. Address 0b1100001x is NACKed
1: Enabled: Device default address enabled. Address 0b1100001x is ACKed

ALERTEN

Bit 22: SMBUS alert enable.

Allowed values:
0: Disabled: In device mode (SMBHEN=Disabled) Releases SMBA pin high and Alert Response Address Header disabled (0001100x) followed by NACK. In host mode (SMBHEN=Enabled) SMBus Alert pin (SMBA) not supported
1: Enabled: In device mode (SMBHEN=Disabled) Drives SMBA pin low and Alert Response Address Header enabled (0001100x) followed by ACK.In host mode (SMBHEN=Enabled) SMBus Alert pin (SMBA) supported

PECEN

Bit 23: PEC enable.

Allowed values:
0: Disabled: PEC calculation disabled
1: Enabled: PEC calculation enabled

CR2

Control register 2

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

11/11 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
					PECBYTE rw	AUTOEND rw	RELOAD rw	NBYTES rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
NACK rw	STOP rw	START rw	HEAD10R rw	ADD10 rw	RD_WRN rw	SADD rw

Toggle fields

SADD

Bits 0-9: Slave address bit 9:8 (master mode).

Allowed values: 0x0-0x3ff

RD_WRN

Bit 10: Transfer direction (master mode).

Allowed values:
0: Write: Master requests a write transfer
1: Read: Master requests a read transfer

ADD10

Bit 11: 10-bit addressing mode (master mode).

Allowed values:
0: Bit7: The master operates in 7-bit addressing mode
1: Bit10: The master operates in 10-bit addressing mode

HEAD10R

Bit 12: 10-bit address header only read direction (master receiver mode).

Allowed values:
0: Complete: The master sends the complete 10 bit slave address read sequence
1: Partial: The master only sends the 1st 7 bits of the 10 bit address, followed by Read direction

START

Bit 13: Start generation.

Allowed values:
0: NoStart: No Start generation
1: Start: Restart/Start generation

STOP

Bit 14: Stop generation (master mode).

Allowed values:
0: NoStop: No Stop generation
1: Stop: Stop generation after current byte transfer

NACK

Bit 15: NACK generation (slave mode).

Allowed values:
0: Ack: an ACK is sent after current received byte
1: Nack: a NACK is sent after current received byte

NBYTES

Bits 16-23: Number of bytes.

Allowed values: 0x0-0xff

RELOAD

Bit 24: NBYTES reload mode.

Allowed values:
0: Completed: The transfer is completed after the NBYTES data transfer (STOP or RESTART will follow)
1: NotCompleted: The transfer is not completed after the NBYTES data transfer (NBYTES will be reloaded)

AUTOEND

Bit 25: Automatic end mode (master mode).

Allowed values:
0: Software: Software end mode: TC flag is set when NBYTES data are transferred, stretching SCL low
1: Automatic: Automatic end mode: a STOP condition is automatically sent when NBYTES data are transferred

PECBYTE

Bit 26: Packet error checking byte.

Allowed values:
0: NoPec: No PEC transfer
1: Pec: PEC transmission/reception is requested

OAR1

Own address register 1

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

3/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OA1EN rw					OA1MODE rw	OA1 rw

Toggle fields

OA1

Bits 0-9: Interface address.

Allowed values: 0x0-0x3ff

OA1MODE

Bit 10: Own Address 1 10-bit mode.

Allowed values:
0: Bit7: Own address 1 is a 7-bit address
1: Bit10: Own address 1 is a 10-bit address

OA1EN

Bit 15: Own Address 1 enable.

Allowed values:
0: Disabled: Own address 1 disabled. The received slave address OA1 is NACKed
1: Enabled: Own address 1 enabled. The received slave address OA1 is ACKed

OAR2

Own address register 2

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

3/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OA2EN rw					OA2MSK rw			OA2 rw

Toggle fields

OA2

Bits 1-7: Interface address.

Allowed values: 0x0-0x7f

OA2MSK

Bits 8-10: Own Address 2 masks.

Allowed values:
0: NoMask: No mask
1: Mask1: OA2[1] is masked and don’t care. Only OA2[7:2] are compared
2: Mask2: OA2[2:1] are masked and don’t care. Only OA2[7:3] are compared
3: Mask3: OA2[3:1] are masked and don’t care. Only OA2[7:4] are compared
4: Mask4: OA2[4:1] are masked and don’t care. Only OA2[7:5] are compared
5: Mask5: OA2[5:1] are masked and don’t care. Only OA2[7:6] are compared
6: Mask6: OA2[6:1] are masked and don’t care. Only OA2[7] is compared.
7: Mask7: OA2[7:1] are masked and don’t care. No comparison is done, and all (except reserved) 7-bit received addresses are acknowledged

OA2EN

Bit 15: Own Address 2 enable.

Allowed values:
0: Disabled: Own address 2 disabled. The received slave address OA2 is NACKed
1: Enabled: Own address 2 enabled. The received slave address OA2 is ACKed

TIMINGR

Timing register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PRESC rw								SCLDEL rw				SDADEL rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SCLH rw								SCLL rw

Toggle fields

SCLL

Bits 0-7: SCL low period (master mode).

Allowed values: 0x0-0xff

SCLH

Bits 8-15: SCL high period (master mode).

Allowed values: 0x0-0xff

SDADEL

Bits 16-19: Data hold time.

Allowed values: 0x0-0xf

SCLDEL

Bits 20-23: Data setup time.

Allowed values: 0x0-0xf

PRESC

Bits 28-31: Timing prescaler.

Allowed values: 0x0-0xf

TIMEOUTR

Status register 1

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
TEXTEN rw				TIMEOUTB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TIMOUTEN rw			TIDLE rw	TIMEOUTA rw

Toggle fields

TIMEOUTA

Bits 0-11: Bus timeout A.

Allowed values: 0x0-0xfff

TIDLE

Bit 12: Idle clock timeout detection.

Allowed values:
0: Disabled: TIMEOUTA is used to detect SCL low timeout
1: Enabled: TIMEOUTA is used to detect both SCL and SDA high timeout (bus idle condition)

TIMOUTEN

Bit 15: Clock timeout enable.

Allowed values:
0: Disabled: SCL timeout detection is disabled
1: Enabled: SCL timeout detection is enabled

TIMEOUTB

Bits 16-27: Bus timeout B.

Allowed values: 0x0-0xfff

TEXTEN

Bit 31: Extended clock timeout enable.

Allowed values:
0: Disabled: Extended clock timeout detection is disabled
1: Enabled: Extended clock timeout detection is enabled

ISR

Interrupt and Status register

Offset: 0x18, size: 32, reset: 0x00000001, access: Unspecified

17/17 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								ADDCODE r							DIR r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BUSY r		ALERT r	TIMEOUT r	PECERR r	OVR r	ARLO r	BERR r	TCR r	TC r	STOPF r	NACKF r	ADDR r	RXNE r	TXIS rw	TXE rw

Toggle fields

TXE

Bit 0: Transmit data register empty (transmitters).

Allowed values:
0: NotEmpty: TXDR register not empty
1: Empty: TXDR register empty

TXIS

Bit 1: Transmit interrupt status (transmitters).

Allowed values:
0: NotEmpty: The TXDR register is not empty
1: Empty: The TXDR register is empty and the data to be transmitted must be written in the TXDR register

RXNE

Bit 2: Receive data register not empty (receivers).

Allowed values:
0: Empty: The RXDR register is empty
1: NotEmpty: Received data is copied into the RXDR register, and is ready to be read

ADDR

Bit 3: Address matched (slave mode).

Allowed values:
0: NotMatch: Adress mismatched or not received
1: Match: Received slave address matched with one of the enabled slave addresses

NACKF

Bit 4: Not acknowledge received flag.

Allowed values:
0: NoNack: No NACK has been received
1: Nack: NACK has been received

STOPF

Bit 5: Stop detection flag.

Allowed values:
0: NoStop: No Stop condition detected
1: Stop: Stop condition detected

TC

Bit 6: Transfer Complete (master mode).

Allowed values:
0: NotComplete: Transfer is not complete
1: Complete: NBYTES has been transfered

TCR

Bit 7: Transfer Complete Reload.

Allowed values:
0: NotComplete: Transfer is not complete
1: Complete: NBYTES has been transfered

BERR

Bit 8: Bus error.

Allowed values:
0: NoError: No bus error
1: Error: Misplaced Start and Stop condition is detected

ARLO

Bit 9: Arbitration lost.

Allowed values:
0: NotLost: No arbitration lost
1: Lost: Arbitration lost

OVR

Bit 10: Overrun/Underrun (slave mode).

Allowed values:
0: NoOverrun: No overrun/underrun error occurs
1: Overrun: slave mode with NOSTRETCH=1, when an overrun/underrun error occurs

PECERR

Bit 11: PEC Error in reception.

Allowed values:
0: Match: Received PEC does match with PEC register
1: NoMatch: Received PEC does not match with PEC register

TIMEOUT

Bit 12: Timeout or t_low detection flag.

Allowed values:
0: NoTimeout: No timeout occured
1: Timeout: Timeout occured

ALERT

Bit 13: SMBus alert.

Allowed values:
0: NoAlert: SMBA alert is not detected
1: Alert: SMBA alert event is detected on SMBA pin

BUSY

Bit 15: Bus busy.

Allowed values:
0: NotBusy: No communication is in progress on the bus
1: Busy: A communication is in progress on the bus

DIR

Bit 16: Transfer direction (Slave mode).

Allowed values:
0: Write: Write transfer, slave enters receiver mode
1: Read: Read transfer, slave enters transmitter mode

ADDCODE

Bits 17-23: Address match code (Slave mode).

Allowed values: 0x0-0x7f

ICR

Interrupt clear register

Offset: 0x1c, size: 32, reset: 0x00000000, access: write-only

9/9 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		ALERTCF w	TIMOUTCF w	PECCF w	OVRCF w	ARLOCF w	BERRCF w			STOPCF w	NACKCF w	ADDRCF w

Toggle fields

ADDRCF

Bit 3: Address Matched flag clear.

Allowed values:
1: Clear: Clears the ADDR flag in ISR register

NACKCF

Bit 4: Not Acknowledge flag clear.

Allowed values:
1: Clear: Clears the NACK flag in ISR register

STOPCF

Bit 5: Stop detection flag clear.

Allowed values:
1: Clear: Clears the STOP flag in ISR register

BERRCF

Bit 8: Bus error flag clear.

Allowed values:
1: Clear: Clears the BERR flag in ISR register

ARLOCF

Bit 9: Arbitration lost flag clear.

Allowed values:
1: Clear: Clears the ARLO flag in ISR register

OVRCF

Bit 10: Overrun/Underrun flag clear.

Allowed values:
1: Clear: Clears the OVR flag in ISR register

PECCF

Bit 11: PEC Error flag clear.

Allowed values:
1: Clear: Clears the PEC flag in ISR register

TIMOUTCF

Bit 12: Timeout detection flag clear.

Allowed values:
1: Clear: Clears the TIMOUT flag in ISR register

ALERTCF

Bit 13: Alert flag clear.

Allowed values:
1: Clear: Clears the ALERT flag in ISR register

PECR

PEC register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								PEC r

Toggle fields

PEC

Bits 0-7: Packet error checking register.

Allowed values: 0x0-0xff

RXDR

Receive data register

Offset: 0x24, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								RXDATA r

Toggle fields

RXDATA

Bits 0-7: 8-bit receive data.

Allowed values: 0x0-0xff

TXDR

Transmit data register

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								TXDATA rw

Toggle fields

TXDATA

Bits 0-7: 8-bit transmit data.

Allowed values: 0x0-0xff

I2C3

0x40007800: Inter-integrated circuit

76/77 fields covered.

Toggle register map

Offset	Name	31	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	CR1						PECEN	ALERTEN	SMBDEN	SMBHEN	GCEN	WUPEN	NOSTRETCH	SBC	RXDMAEN	TXDMAEN	SWRST	ANFOFF	DNF				ERRIE	TCIE	STOPIE	NACKIE	ADDRIE	RXIE	TXIE	PE
0x4	CR2			PECBYTE	AUTOEND	RELOAD	NBYTES								NACK	STOP	START	HEAD10R	ADD10	RD_WRN	SADD
0x8	OAR1														OA1EN					OA1MODE	OA1
0xc	OAR2														OA2EN					OA2MSK			OA2
0x10	TIMINGR	PRESC					SCLDEL				SDADEL				SCLH								SCLL
0x14	TIMEOUTR	TEXTEN	TIMEOUTB												TIMOUTEN			TIDLE	TIMEOUTA
0x18	ISR						ADDCODE							DIR	BUSY		ALERT	TIMEOUT	PECERR	OVR	ARLO	BERR	TCR	TC	STOPF	NACKF	ADDR	RXNE	TXIS	TXE
0x1c	ICR																ALERTCF	TIMOUTCF	PECCF	OVRCF	ARLOCF	BERRCF			STOPCF	NACKCF	ADDRCF
0x20	PECR																						PEC
0x24	RXDR																						RXDATA
0x28	TXDR																						TXDATA

Toggle registers

CR1

Control register 1

Offset: 0x0, size: 32, reset: 0x00000000, access: Unspecified

20/21 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								PECEN rw	ALERTEN rw	SMBDEN rw	SMBHEN rw	GCEN rw	WUPEN rw	NOSTRETCH rw	SBC rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RXDMAEN rw	TXDMAEN rw	SWRST w	ANFOFF rw	DNF rw				ERRIE rw	TCIE rw	STOPIE rw	NACKIE rw	ADDRIE rw	RXIE rw	TXIE rw	PE rw

Toggle fields

PE

Bit 0: Peripheral enable.

Allowed values:
0: Disabled: Peripheral disabled
1: Enabled: Peripheral enabled

TXIE

Bit 1: TX Interrupt enable.

Allowed values:
0: Disabled: Transmit (TXIS) interrupt disabled
1: Enabled: Transmit (TXIS) interrupt enabled

RXIE

Bit 2: RX Interrupt enable.

Allowed values:
0: Disabled: Receive (RXNE) interrupt disabled
1: Enabled: Receive (RXNE) interrupt enabled

ADDRIE

Bit 3: Address match interrupt enable (slave only).

Allowed values:
0: Disabled: Address match (ADDR) interrupts disabled
1: Enabled: Address match (ADDR) interrupts enabled

NACKIE

Bit 4: Not acknowledge received interrupt enable.

Allowed values:
0: Disabled: Not acknowledge (NACKF) received interrupts disabled
1: Enabled: Not acknowledge (NACKF) received interrupts enabled

STOPIE

Bit 5: STOP detection Interrupt enable.

Allowed values:
0: Disabled: Stop detection (STOPF) interrupt disabled
1: Enabled: Stop detection (STOPF) interrupt enabled

TCIE

Bit 6: Transfer Complete interrupt enable.

Allowed values:
0: Disabled: Transfer Complete interrupt disabled
1: Enabled: Transfer Complete interrupt enabled

ERRIE

Bit 7: Error interrupts enable.

Allowed values:
0: Disabled: Error detection interrupts disabled
1: Enabled: Error detection interrupts enabled

DNF

Bits 8-11: Digital noise filter.

Allowed values:
0: NoFilter: Digital filter disabled
1: Filter1: Digital filter enabled and filtering capability up to 1 tI2CCLK
2: Filter2: Digital filter enabled and filtering capability up to 2 tI2CCLK
3: Filter3: Digital filter enabled and filtering capability up to 3 tI2CCLK
4: Filter4: Digital filter enabled and filtering capability up to 4 tI2CCLK
5: Filter5: Digital filter enabled and filtering capability up to 5 tI2CCLK
6: Filter6: Digital filter enabled and filtering capability up to 6 tI2CCLK
7: Filter7: Digital filter enabled and filtering capability up to 7 tI2CCLK
8: Filter8: Digital filter enabled and filtering capability up to 8 tI2CCLK
9: Filter9: Digital filter enabled and filtering capability up to 9 tI2CCLK
10: Filter10: Digital filter enabled and filtering capability up to 10 tI2CCLK
11: Filter11: Digital filter enabled and filtering capability up to 11 tI2CCLK
12: Filter12: Digital filter enabled and filtering capability up to 12 tI2CCLK
13: Filter13: Digital filter enabled and filtering capability up to 13 tI2CCLK
14: Filter14: Digital filter enabled and filtering capability up to 14 tI2CCLK
15: Filter15: Digital filter enabled and filtering capability up to 15 tI2CCLK

ANFOFF

Bit 12: Analog noise filter OFF.

Allowed values:
0: Enabled: Analog noise filter enabled
1: Disabled: Analog noise filter disabled

SWRST

Bit 13: Software reset.

TXDMAEN

Bit 14: DMA transmission requests enable.

Allowed values:
0: Disabled: DMA mode disabled for transmission
1: Enabled: DMA mode enabled for transmission

RXDMAEN

Bit 15: DMA reception requests enable.

Allowed values:
0: Disabled: DMA mode disabled for reception
1: Enabled: DMA mode enabled for reception

SBC

Bit 16: Slave byte control.

Allowed values:
0: Disabled: Slave byte control disabled
1: Enabled: Slave byte control enabled

NOSTRETCH

Bit 17: Clock stretching disable.

Allowed values:
0: Enabled: Clock stretching enabled
1: Disabled: Clock stretching disabled

WUPEN

Bit 18: Wakeup from STOP enable.

Allowed values:
0: Disabled: Wakeup from Stop mode disabled
1: Enabled: Wakeup from Stop mode enabled

GCEN

Bit 19: General call enable.

Allowed values:
0: Disabled: General call disabled. Address 0b00000000 is NACKed
1: Enabled: General call enabled. Address 0b00000000 is ACKed

SMBHEN

Bit 20: SMBus Host address enable.

Allowed values:
0: Disabled: Host address disabled. Address 0b0001000x is NACKed
1: Enabled: Host address enabled. Address 0b0001000x is ACKed

SMBDEN

Bit 21: SMBus Device Default address enable.

Allowed values:
0: Disabled: Device default address disabled. Address 0b1100001x is NACKed
1: Enabled: Device default address enabled. Address 0b1100001x is ACKed

ALERTEN

Bit 22: SMBUS alert enable.

Allowed values:
0: Disabled: In device mode (SMBHEN=Disabled) Releases SMBA pin high and Alert Response Address Header disabled (0001100x) followed by NACK. In host mode (SMBHEN=Enabled) SMBus Alert pin (SMBA) not supported
1: Enabled: In device mode (SMBHEN=Disabled) Drives SMBA pin low and Alert Response Address Header enabled (0001100x) followed by ACK.In host mode (SMBHEN=Enabled) SMBus Alert pin (SMBA) supported

PECEN

Bit 23: PEC enable.

Allowed values:
0: Disabled: PEC calculation disabled
1: Enabled: PEC calculation enabled

CR2

Control register 2

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

11/11 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
					PECBYTE rw	AUTOEND rw	RELOAD rw	NBYTES rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
NACK rw	STOP rw	START rw	HEAD10R rw	ADD10 rw	RD_WRN rw	SADD rw

Toggle fields

SADD

Bits 0-9: Slave address bit 9:8 (master mode).

Allowed values: 0x0-0x3ff

RD_WRN

Bit 10: Transfer direction (master mode).

Allowed values:
0: Write: Master requests a write transfer
1: Read: Master requests a read transfer

ADD10

Bit 11: 10-bit addressing mode (master mode).

Allowed values:
0: Bit7: The master operates in 7-bit addressing mode
1: Bit10: The master operates in 10-bit addressing mode

HEAD10R

Bit 12: 10-bit address header only read direction (master receiver mode).

Allowed values:
0: Complete: The master sends the complete 10 bit slave address read sequence
1: Partial: The master only sends the 1st 7 bits of the 10 bit address, followed by Read direction

START

Bit 13: Start generation.

Allowed values:
0: NoStart: No Start generation
1: Start: Restart/Start generation

STOP

Bit 14: Stop generation (master mode).

Allowed values:
0: NoStop: No Stop generation
1: Stop: Stop generation after current byte transfer

NACK

Bit 15: NACK generation (slave mode).

Allowed values:
0: Ack: an ACK is sent after current received byte
1: Nack: a NACK is sent after current received byte

NBYTES

Bits 16-23: Number of bytes.

Allowed values: 0x0-0xff

RELOAD

Bit 24: NBYTES reload mode.

Allowed values:
0: Completed: The transfer is completed after the NBYTES data transfer (STOP or RESTART will follow)
1: NotCompleted: The transfer is not completed after the NBYTES data transfer (NBYTES will be reloaded)

AUTOEND

Bit 25: Automatic end mode (master mode).

Allowed values:
0: Software: Software end mode: TC flag is set when NBYTES data are transferred, stretching SCL low
1: Automatic: Automatic end mode: a STOP condition is automatically sent when NBYTES data are transferred

PECBYTE

Bit 26: Packet error checking byte.

Allowed values:
0: NoPec: No PEC transfer
1: Pec: PEC transmission/reception is requested

OAR1

Own address register 1

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

3/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OA1EN rw					OA1MODE rw	OA1 rw

Toggle fields

OA1

Bits 0-9: Interface address.

Allowed values: 0x0-0x3ff

OA1MODE

Bit 10: Own Address 1 10-bit mode.

Allowed values:
0: Bit7: Own address 1 is a 7-bit address
1: Bit10: Own address 1 is a 10-bit address

OA1EN

Bit 15: Own Address 1 enable.

Allowed values:
0: Disabled: Own address 1 disabled. The received slave address OA1 is NACKed
1: Enabled: Own address 1 enabled. The received slave address OA1 is ACKed

OAR2

Own address register 2

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

3/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OA2EN rw					OA2MSK rw			OA2 rw

Toggle fields

OA2

Bits 1-7: Interface address.

Allowed values: 0x0-0x7f

OA2MSK

Bits 8-10: Own Address 2 masks.

Allowed values:
0: NoMask: No mask
1: Mask1: OA2[1] is masked and don’t care. Only OA2[7:2] are compared
2: Mask2: OA2[2:1] are masked and don’t care. Only OA2[7:3] are compared
3: Mask3: OA2[3:1] are masked and don’t care. Only OA2[7:4] are compared
4: Mask4: OA2[4:1] are masked and don’t care. Only OA2[7:5] are compared
5: Mask5: OA2[5:1] are masked and don’t care. Only OA2[7:6] are compared
6: Mask6: OA2[6:1] are masked and don’t care. Only OA2[7] is compared.
7: Mask7: OA2[7:1] are masked and don’t care. No comparison is done, and all (except reserved) 7-bit received addresses are acknowledged

OA2EN

Bit 15: Own Address 2 enable.

Allowed values:
0: Disabled: Own address 2 disabled. The received slave address OA2 is NACKed
1: Enabled: Own address 2 enabled. The received slave address OA2 is ACKed

TIMINGR

Timing register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PRESC rw								SCLDEL rw				SDADEL rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SCLH rw								SCLL rw

Toggle fields

SCLL

Bits 0-7: SCL low period (master mode).

Allowed values: 0x0-0xff

SCLH

Bits 8-15: SCL high period (master mode).

Allowed values: 0x0-0xff

SDADEL

Bits 16-19: Data hold time.

Allowed values: 0x0-0xf

SCLDEL

Bits 20-23: Data setup time.

Allowed values: 0x0-0xf

PRESC

Bits 28-31: Timing prescaler.

Allowed values: 0x0-0xf

TIMEOUTR

Status register 1

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
TEXTEN rw				TIMEOUTB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TIMOUTEN rw			TIDLE rw	TIMEOUTA rw

Toggle fields

TIMEOUTA

Bits 0-11: Bus timeout A.

Allowed values: 0x0-0xfff

TIDLE

Bit 12: Idle clock timeout detection.

Allowed values:
0: Disabled: TIMEOUTA is used to detect SCL low timeout
1: Enabled: TIMEOUTA is used to detect both SCL and SDA high timeout (bus idle condition)

TIMOUTEN

Bit 15: Clock timeout enable.

Allowed values:
0: Disabled: SCL timeout detection is disabled
1: Enabled: SCL timeout detection is enabled

TIMEOUTB

Bits 16-27: Bus timeout B.

Allowed values: 0x0-0xfff

TEXTEN

Bit 31: Extended clock timeout enable.

Allowed values:
0: Disabled: Extended clock timeout detection is disabled
1: Enabled: Extended clock timeout detection is enabled

ISR

Interrupt and Status register

Offset: 0x18, size: 32, reset: 0x00000001, access: Unspecified

17/17 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								ADDCODE r							DIR r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BUSY r		ALERT r	TIMEOUT r	PECERR r	OVR r	ARLO r	BERR r	TCR r	TC r	STOPF r	NACKF r	ADDR r	RXNE r	TXIS rw	TXE rw

Toggle fields

TXE

Bit 0: Transmit data register empty (transmitters).

Allowed values:
0: NotEmpty: TXDR register not empty
1: Empty: TXDR register empty

TXIS

Bit 1: Transmit interrupt status (transmitters).

Allowed values:
0: NotEmpty: The TXDR register is not empty
1: Empty: The TXDR register is empty and the data to be transmitted must be written in the TXDR register

RXNE

Bit 2: Receive data register not empty (receivers).

Allowed values:
0: Empty: The RXDR register is empty
1: NotEmpty: Received data is copied into the RXDR register, and is ready to be read

ADDR

Bit 3: Address matched (slave mode).

Allowed values:
0: NotMatch: Adress mismatched or not received
1: Match: Received slave address matched with one of the enabled slave addresses

NACKF

Bit 4: Not acknowledge received flag.

Allowed values:
0: NoNack: No NACK has been received
1: Nack: NACK has been received

STOPF

Bit 5: Stop detection flag.

Allowed values:
0: NoStop: No Stop condition detected
1: Stop: Stop condition detected

TC

Bit 6: Transfer Complete (master mode).

Allowed values:
0: NotComplete: Transfer is not complete
1: Complete: NBYTES has been transfered

TCR

Bit 7: Transfer Complete Reload.

Allowed values:
0: NotComplete: Transfer is not complete
1: Complete: NBYTES has been transfered

BERR

Bit 8: Bus error.

Allowed values:
0: NoError: No bus error
1: Error: Misplaced Start and Stop condition is detected

ARLO

Bit 9: Arbitration lost.

Allowed values:
0: NotLost: No arbitration lost
1: Lost: Arbitration lost

OVR

Bit 10: Overrun/Underrun (slave mode).

Allowed values:
0: NoOverrun: No overrun/underrun error occurs
1: Overrun: slave mode with NOSTRETCH=1, when an overrun/underrun error occurs

PECERR

Bit 11: PEC Error in reception.

Allowed values:
0: Match: Received PEC does match with PEC register
1: NoMatch: Received PEC does not match with PEC register

TIMEOUT

Bit 12: Timeout or t_low detection flag.

Allowed values:
0: NoTimeout: No timeout occured
1: Timeout: Timeout occured

ALERT

Bit 13: SMBus alert.

Allowed values:
0: NoAlert: SMBA alert is not detected
1: Alert: SMBA alert event is detected on SMBA pin

BUSY

Bit 15: Bus busy.

Allowed values:
0: NotBusy: No communication is in progress on the bus
1: Busy: A communication is in progress on the bus

DIR

Bit 16: Transfer direction (Slave mode).

Allowed values:
0: Write: Write transfer, slave enters receiver mode
1: Read: Read transfer, slave enters transmitter mode

ADDCODE

Bits 17-23: Address match code (Slave mode).

Allowed values: 0x0-0x7f

ICR

Interrupt clear register

Offset: 0x1c, size: 32, reset: 0x00000000, access: write-only

9/9 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		ALERTCF w	TIMOUTCF w	PECCF w	OVRCF w	ARLOCF w	BERRCF w			STOPCF w	NACKCF w	ADDRCF w

Toggle fields

ADDRCF

Bit 3: Address Matched flag clear.

Allowed values:
1: Clear: Clears the ADDR flag in ISR register

NACKCF

Bit 4: Not Acknowledge flag clear.

Allowed values:
1: Clear: Clears the NACK flag in ISR register

STOPCF

Bit 5: Stop detection flag clear.

Allowed values:
1: Clear: Clears the STOP flag in ISR register

BERRCF

Bit 8: Bus error flag clear.

Allowed values:
1: Clear: Clears the BERR flag in ISR register

ARLOCF

Bit 9: Arbitration lost flag clear.

Allowed values:
1: Clear: Clears the ARLO flag in ISR register

OVRCF

Bit 10: Overrun/Underrun flag clear.

Allowed values:
1: Clear: Clears the OVR flag in ISR register

PECCF

Bit 11: PEC Error flag clear.

Allowed values:
1: Clear: Clears the PEC flag in ISR register

TIMOUTCF

Bit 12: Timeout detection flag clear.

Allowed values:
1: Clear: Clears the TIMOUT flag in ISR register

ALERTCF

Bit 13: Alert flag clear.

Allowed values:
1: Clear: Clears the ALERT flag in ISR register

PECR

PEC register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								PEC r

Toggle fields

PEC

Bits 0-7: Packet error checking register.

Allowed values: 0x0-0xff

RXDR

Receive data register

Offset: 0x24, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								RXDATA r

Toggle fields

RXDATA

Bits 0-7: 8-bit receive data.

Allowed values: 0x0-0xff

TXDR

Transmit data register

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								TXDATA rw

Toggle fields

TXDATA

Bits 0-7: 8-bit transmit data.

Allowed values: 0x0-0xff

I2S2ext

0x40003400: Serial peripheral interface/Inter-IC sound

53/53 fields covered.

Toggle register map

Offset	Name	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0 (16-bit)	CR1	BIDIMODE	BIDIOE	CRCEN	CRCNEXT	CRCL	RXONLY	SSM	SSI	LSBFIRST	SPE	BR			MSTR	CPOL	CPHA
0x4 (16-bit)	CR2		LDMA_TX	LDMA_RX	FRXTH	DS				TXEIE	RXNEIE	ERRIE	FRF	NSSP	SSOE	TXDMAEN	RXDMAEN
0x8 (16-bit)	SR				FTLVL		FRLVL		FRE	BSY	OVR	MODF	CRCERR	UDR	CHSIDE	TXE	RXNE
0xc (16-bit)	DR	DR
0xc (8-bit)	DR8									DR
0x10 (16-bit)	CRCPR	CRCPOLY
0x14 (16-bit)	RXCRCR	RxCRC
0x18 (16-bit)	TXCRCR	TxCRC
0x1c (16-bit)	I2SCFGR					I2SMOD	I2SE	I2SCFG		PCMSYNC		I2SSTD		CKPOL	DATLEN		CHLEN
0x20 (16-bit)	I2SPR							MCKOE	ODD	I2SDIV

Toggle registers

CR1

control register 1

Offset: 0x0, size: 16, reset: 0x00000000, access: read-write

14/14 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BIDIMODE rw	BIDIOE rw	CRCEN rw	CRCNEXT rw	CRCL rw	RXONLY rw	SSM rw	SSI rw	LSBFIRST rw	SPE rw	BR rw			MSTR rw	CPOL rw	CPHA rw

Toggle fields

CPHA

Bit 0: Clock phase.

Allowed values:
0: FirstEdge: The first clock transition is the first data capture edge
1: SecondEdge: The second clock transition is the first data capture edge

CPOL

Bit 1: Clock polarity.

Allowed values:
0: IdleLow: CK to 0 when idle
1: IdleHigh: CK to 1 when idle

MSTR

Bit 2: Master selection.

Allowed values:
0: Slave: Slave configuration
1: Master: Master configuration

BR

Bits 3-5: Baud rate control.

Allowed values:
0: Div2: f_PCLK / 2
1: Div4: f_PCLK / 4
2: Div8: f_PCLK / 8
3: Div16: f_PCLK / 16
4: Div32: f_PCLK / 32
5: Div64: f_PCLK / 64
6: Div128: f_PCLK / 128
7: Div256: f_PCLK / 256

SPE

Bit 6: SPI enable.

Allowed values:
0: Disabled: Peripheral disabled
1: Enabled: Peripheral enabled

LSBFIRST

Bit 7: Frame format.

Allowed values:
0: MSBFirst: Data is transmitted/received with the MSB first
1: LSBFirst: Data is transmitted/received with the LSB first

SSI

Bit 8: Internal slave select.

Allowed values:
0: SlaveSelected: 0 is forced onto the NSS pin and the I/O value of the NSS pin is ignored
1: SlaveNotSelected: 1 is forced onto the NSS pin and the I/O value of the NSS pin is ignored

SSM

Bit 9: Software slave management.

Allowed values:
0: Disabled: Software slave management disabled
1: Enabled: Software slave management enabled

RXONLY

Bit 10: Receive only.

Allowed values:
0: FullDuplex: Full duplex (Transmit and receive)
1: OutputDisabled: Output disabled (Receive-only mode)

CRCL

Bit 11: CRC length.

Allowed values:
0: EightBit: 8-bit CRC length
1: SixteenBit: 16-bit CRC length

CRCNEXT

Bit 12: CRC transfer next.

Allowed values:
0: TxBuffer: Next transmit value is from Tx buffer
1: CRC: Next transmit value is from Tx CRC register

CRCEN

Bit 13: Hardware CRC calculation enable.

Allowed values:
0: Disabled: CRC calculation disabled
1: Enabled: CRC calculation enabled

BIDIOE

Bit 14: Output enable in bidirectional mode.

Allowed values:
0: OutputDisabled: Output disabled (receive-only mode)
1: OutputEnabled: Output enabled (transmit-only mode)

BIDIMODE

Bit 15: Bidirectional data mode enable.

Allowed values:
0: Unidirectional: 2-line unidirectional data mode selected
1: Bidirectional: 1-line bidirectional data mode selected

CR2

control register 2

Offset: 0x4, size: 16, reset: 0x00000000, access: read-write

12/12 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	LDMA_TX rw	LDMA_RX rw	FRXTH rw	DS rw				TXEIE rw	RXNEIE rw	ERRIE rw	FRF rw	NSSP rw	SSOE rw	TXDMAEN rw	RXDMAEN rw

Toggle fields

RXDMAEN

Bit 0: Rx buffer DMA enable.

Allowed values:
0: Disabled: Rx buffer DMA disabled
1: Enabled: Rx buffer DMA enabled

TXDMAEN

Bit 1: Tx buffer DMA enable.

Allowed values:
0: Disabled: Tx buffer DMA disabled
1: Enabled: Tx buffer DMA enabled

SSOE

Bit 2: SS output enable.

Allowed values:
0: Disabled: SS output is disabled in master mode
1: Enabled: SS output is enabled in master mode

NSSP

Bit 3: NSS pulse management.

Allowed values:
0: NoPulse: No NSS pulse
1: PulseGenerated: NSS pulse generated

FRF

Bit 4: Frame format.

Allowed values:
0: Motorola: SPI Motorola mode
1: TI: SPI TI mode

ERRIE

Bit 5: Error interrupt enable.

Allowed values:
0: Masked: Error interrupt masked
1: NotMasked: Error interrupt not masked

RXNEIE

Bit 6: RX buffer not empty interrupt enable.

Allowed values:
0: Masked: RXE interrupt masked
1: NotMasked: RXE interrupt not masked

TXEIE

Bit 7: Tx buffer empty interrupt enable.

Allowed values:
0: Masked: TXE interrupt masked
1: NotMasked: TXE interrupt not masked

DS

Bits 8-11: Data size.

Allowed values:
3: FourBit: 4-bit
4: FiveBit: 5-bit
5: SixBit: 6-bit
6: SevenBit: 7-bit
7: EightBit: 8-bit
8: NineBit: 9-bit
9: TenBit: 10-bit
10: ElevenBit: 11-bit
11: TwelveBit: 12-bit
12: ThirteenBit: 13-bit
13: FourteenBit: 14-bit
14: FifteenBit: 15-bit
15: SixteenBit: 16-bit

FRXTH

Bit 12: FIFO reception threshold.

Allowed values:
0: Half: RXNE event is generated if the FIFO level is greater than or equal to 1/2 (16-bit)
1: Quarter: RXNE event is generated if the FIFO level is greater than or equal to 1/4 (8-bit)

LDMA_RX

Bit 13: Last DMA transfer for reception.

Allowed values:
0: Even: Number of data to transfer for receive is even
1: Odd: Number of data to transfer for receive is odd

LDMA_TX

Bit 14: Last DMA transfer for transmission.

Allowed values:
0: Even: Number of data to transfer for transmit is even
1: Odd: Number of data to transfer for transmit is odd

SR

status register

Offset: 0x8, size: 16, reset: 0x00000002, access: Unspecified

11/11 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			FTLVL r		FRLVL r		FRE r	BSY r	OVR r	MODF r	CRCERR rw	UDR r	CHSIDE r	TXE r	RXNE r

Toggle fields

RXNE

Bit 0: Receive buffer not empty.

Allowed values:
0: Empty: Rx buffer empty
1: NotEmpty: Rx buffer not empty

TXE

Bit 1: Transmit buffer empty.

Allowed values:
0: NotEmpty: Tx buffer not empty
1: Empty: Tx buffer empty

CHSIDE

Bit 2: Channel side.

Allowed values:
0: Left: Channel left has to be transmitted or has been received
1: Right: Channel right has to be transmitted or has been received

UDR

Bit 3: Underrun flag.

Allowed values:
0: NoUnderrun: No underrun occurred
1: Underrun: Underrun occurred

CRCERR

Bit 4: CRC error flag.

Allowed values:
0: Match: CRC value received matches the SPIx_RXCRCR value
1: NoMatch: CRC value received does not match the SPIx_RXCRCR value

MODF

Bit 5: Mode fault.

Allowed values:
0: NoFault: No mode fault occurred
1: Fault: Mode fault occurred

OVR

Bit 6: Overrun flag.

Allowed values:
0: NoOverrun: No overrun occurred
1: Overrun: Overrun occurred

BSY

Bit 7: Busy flag.

Allowed values:
0: NotBusy: SPI not busy
1: Busy: SPI busy

FRE

Bit 8: TI frame format error.

Allowed values:
0: NoError: No frame format error
1: Error: A frame format error occurred

FRLVL

Bits 9-10: FIFO reception level.

Allowed values:
0: Empty: Rx FIFO Empty
1: Quarter: Rx 1/4 FIFO
2: Half: Rx 1/2 FIFO
3: Full: Rx FIFO full

FTLVL

Bits 11-12: FIFO transmission level.

Allowed values:
0: Empty: Tx FIFO Empty
1: Quarter: Tx 1/4 FIFO
2: Half: Tx 1/2 FIFO
3: Full: Tx FIFO full

DR

data register

Offset: 0xc, size: 16, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DR rw

Toggle fields

DR

Bits 0-15: Data register.

Allowed values: 0x0-0xffff

DR8

Direct 8-bit access to data register

Offset: 0xc, size: 8, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								DR rw

Toggle fields

DR

Bits 0-7: Data register.

Allowed values: 0x0-0xff

CRCPR

CRC polynomial register

Offset: 0x10, size: 16, reset: 0x00000007, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CRCPOLY rw

Toggle fields

CRCPOLY

Bits 0-15: CRC polynomial register.

Allowed values: 0x0-0xffff

RXCRCR

RX CRC register

Offset: 0x14, size: 16, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RxCRC r

Toggle fields

RxCRC

Bits 0-15: Rx CRC register.

Allowed values: 0x0-0xffff

TXCRCR

TX CRC register

Offset: 0x18, size: 16, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TxCRC r

Toggle fields

TxCRC

Bits 0-15: Tx CRC register.

Allowed values: 0x0-0xffff

I2SCFGR

I2S configuration register

Offset: 0x1c, size: 16, reset: 0x00000000, access: read-write

8/8 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				I2SMOD rw	I2SE rw	I2SCFG rw		PCMSYNC rw		I2SSTD rw		CKPOL rw	DATLEN rw		CHLEN rw

Toggle fields

CHLEN

Bit 0: Channel length (number of bits per audio channel).

Allowed values:
0: SixteenBit: 16-bit wide
1: ThirtyTwoBit: 32-bit wide

DATLEN

Bits 1-2: Data length to be transferred.

Allowed values:
0: SixteenBit: 16-bit data length
1: TwentyFourBit: 24-bit data length
2: ThirtyTwoBit: 32-bit data length

CKPOL

Bit 3: Steady state clock polarity.

Allowed values:
0: IdleLow: I2S clock inactive state is low level
1: IdleHigh: I2S clock inactive state is high level

I2SSTD

Bits 4-5: I2S standard selection.

Allowed values:
0: Philips: I2S Philips standard
1: MSB: MSB justified standard
2: LSB: LSB justified standard
3: PCM: PCM standard

PCMSYNC

Bit 7: PCM frame synchronization.

Allowed values:
0: Short: Short frame synchronisation
1: Long: Long frame synchronisation

I2SCFG

Bits 8-9: I2S configuration mode.

Allowed values:
0: SlaveTx: Slave - transmit
1: SlaveRx: Slave - receive
2: MasterTx: Master - transmit
3: MasterRx: Master - receive

I2SE

Bit 10: I2S Enable.

Allowed values:
0: Disabled: I2S peripheral is disabled
1: Enabled: I2S peripheral is enabled

I2SMOD

Bit 11: I2S mode selection.

Allowed values:
0: SPIMode: SPI mode is selected
1: I2SMode: I2S mode is selected

I2SPR

I2S prescaler register

Offset: 0x20, size: 16, reset: 0x00000010, access: read-write

3/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						MCKOE rw	ODD rw	I2SDIV rw

Toggle fields

I2SDIV

Bits 0-7: I2S Linear prescaler.

Allowed values: 0x2-0xff

ODD

Bit 8: Odd factor for the prescaler.

Allowed values:
0: Even: Real divider value is I2SDIV * 2
1: Odd: Real divider value is (I2SDIV * 2) + 1

MCKOE

Bit 9: Master clock output enable.

Allowed values:
0: Disabled: Master clock output is disabled
1: Enabled: Master clock output is enabled

I2S3ext

0x40004000: Serial peripheral interface/Inter-IC sound

53/53 fields covered.

Toggle register map

Offset	Name	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0 (16-bit)	CR1	BIDIMODE	BIDIOE	CRCEN	CRCNEXT	CRCL	RXONLY	SSM	SSI	LSBFIRST	SPE	BR			MSTR	CPOL	CPHA
0x4 (16-bit)	CR2		LDMA_TX	LDMA_RX	FRXTH	DS				TXEIE	RXNEIE	ERRIE	FRF	NSSP	SSOE	TXDMAEN	RXDMAEN
0x8 (16-bit)	SR				FTLVL		FRLVL		FRE	BSY	OVR	MODF	CRCERR	UDR	CHSIDE	TXE	RXNE
0xc (16-bit)	DR	DR
0xc (8-bit)	DR8									DR
0x10 (16-bit)	CRCPR	CRCPOLY
0x14 (16-bit)	RXCRCR	RxCRC
0x18 (16-bit)	TXCRCR	TxCRC
0x1c (16-bit)	I2SCFGR					I2SMOD	I2SE	I2SCFG		PCMSYNC		I2SSTD		CKPOL	DATLEN		CHLEN
0x20 (16-bit)	I2SPR							MCKOE	ODD	I2SDIV

Toggle registers

CR1

control register 1

Offset: 0x0, size: 16, reset: 0x00000000, access: read-write

14/14 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BIDIMODE rw	BIDIOE rw	CRCEN rw	CRCNEXT rw	CRCL rw	RXONLY rw	SSM rw	SSI rw	LSBFIRST rw	SPE rw	BR rw			MSTR rw	CPOL rw	CPHA rw

Toggle fields

CPHA

Bit 0: Clock phase.

Allowed values:
0: FirstEdge: The first clock transition is the first data capture edge
1: SecondEdge: The second clock transition is the first data capture edge

CPOL

Bit 1: Clock polarity.

Allowed values:
0: IdleLow: CK to 0 when idle
1: IdleHigh: CK to 1 when idle

MSTR

Bit 2: Master selection.

Allowed values:
0: Slave: Slave configuration
1: Master: Master configuration

BR

Bits 3-5: Baud rate control.

Allowed values:
0: Div2: f_PCLK / 2
1: Div4: f_PCLK / 4
2: Div8: f_PCLK / 8
3: Div16: f_PCLK / 16
4: Div32: f_PCLK / 32
5: Div64: f_PCLK / 64
6: Div128: f_PCLK / 128
7: Div256: f_PCLK / 256

SPE

Bit 6: SPI enable.

Allowed values:
0: Disabled: Peripheral disabled
1: Enabled: Peripheral enabled

LSBFIRST

Bit 7: Frame format.

Allowed values:
0: MSBFirst: Data is transmitted/received with the MSB first
1: LSBFirst: Data is transmitted/received with the LSB first

SSI

Bit 8: Internal slave select.

Allowed values:
0: SlaveSelected: 0 is forced onto the NSS pin and the I/O value of the NSS pin is ignored
1: SlaveNotSelected: 1 is forced onto the NSS pin and the I/O value of the NSS pin is ignored

SSM

Bit 9: Software slave management.

Allowed values:
0: Disabled: Software slave management disabled
1: Enabled: Software slave management enabled

RXONLY

Bit 10: Receive only.

Allowed values:
0: FullDuplex: Full duplex (Transmit and receive)
1: OutputDisabled: Output disabled (Receive-only mode)

CRCL

Bit 11: CRC length.

Allowed values:
0: EightBit: 8-bit CRC length
1: SixteenBit: 16-bit CRC length

CRCNEXT

Bit 12: CRC transfer next.

Allowed values:
0: TxBuffer: Next transmit value is from Tx buffer
1: CRC: Next transmit value is from Tx CRC register

CRCEN

Bit 13: Hardware CRC calculation enable.

Allowed values:
0: Disabled: CRC calculation disabled
1: Enabled: CRC calculation enabled

BIDIOE

Bit 14: Output enable in bidirectional mode.

Allowed values:
0: OutputDisabled: Output disabled (receive-only mode)
1: OutputEnabled: Output enabled (transmit-only mode)

BIDIMODE

Bit 15: Bidirectional data mode enable.

Allowed values:
0: Unidirectional: 2-line unidirectional data mode selected
1: Bidirectional: 1-line bidirectional data mode selected

CR2

control register 2

Offset: 0x4, size: 16, reset: 0x00000000, access: read-write

12/12 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	LDMA_TX rw	LDMA_RX rw	FRXTH rw	DS rw				TXEIE rw	RXNEIE rw	ERRIE rw	FRF rw	NSSP rw	SSOE rw	TXDMAEN rw	RXDMAEN rw

Toggle fields

RXDMAEN

Bit 0: Rx buffer DMA enable.

Allowed values:
0: Disabled: Rx buffer DMA disabled
1: Enabled: Rx buffer DMA enabled

TXDMAEN

Bit 1: Tx buffer DMA enable.

Allowed values:
0: Disabled: Tx buffer DMA disabled
1: Enabled: Tx buffer DMA enabled

SSOE

Bit 2: SS output enable.

Allowed values:
0: Disabled: SS output is disabled in master mode
1: Enabled: SS output is enabled in master mode

NSSP

Bit 3: NSS pulse management.

Allowed values:
0: NoPulse: No NSS pulse
1: PulseGenerated: NSS pulse generated

FRF

Bit 4: Frame format.

Allowed values:
0: Motorola: SPI Motorola mode
1: TI: SPI TI mode

ERRIE

Bit 5: Error interrupt enable.

Allowed values:
0: Masked: Error interrupt masked
1: NotMasked: Error interrupt not masked

RXNEIE

Bit 6: RX buffer not empty interrupt enable.

Allowed values:
0: Masked: RXE interrupt masked
1: NotMasked: RXE interrupt not masked

TXEIE

Bit 7: Tx buffer empty interrupt enable.

Allowed values:
0: Masked: TXE interrupt masked
1: NotMasked: TXE interrupt not masked

DS

Bits 8-11: Data size.

Allowed values:
3: FourBit: 4-bit
4: FiveBit: 5-bit
5: SixBit: 6-bit
6: SevenBit: 7-bit
7: EightBit: 8-bit
8: NineBit: 9-bit
9: TenBit: 10-bit
10: ElevenBit: 11-bit
11: TwelveBit: 12-bit
12: ThirteenBit: 13-bit
13: FourteenBit: 14-bit
14: FifteenBit: 15-bit
15: SixteenBit: 16-bit

FRXTH

Bit 12: FIFO reception threshold.

Allowed values:
0: Half: RXNE event is generated if the FIFO level is greater than or equal to 1/2 (16-bit)
1: Quarter: RXNE event is generated if the FIFO level is greater than or equal to 1/4 (8-bit)

LDMA_RX

Bit 13: Last DMA transfer for reception.

Allowed values:
0: Even: Number of data to transfer for receive is even
1: Odd: Number of data to transfer for receive is odd

LDMA_TX

Bit 14: Last DMA transfer for transmission.

Allowed values:
0: Even: Number of data to transfer for transmit is even
1: Odd: Number of data to transfer for transmit is odd

SR

status register

Offset: 0x8, size: 16, reset: 0x00000002, access: Unspecified

11/11 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			FTLVL r		FRLVL r		FRE r	BSY r	OVR r	MODF r	CRCERR rw	UDR r	CHSIDE r	TXE r	RXNE r

Toggle fields

RXNE

Bit 0: Receive buffer not empty.

Allowed values:
0: Empty: Rx buffer empty
1: NotEmpty: Rx buffer not empty

TXE

Bit 1: Transmit buffer empty.

Allowed values:
0: NotEmpty: Tx buffer not empty
1: Empty: Tx buffer empty

CHSIDE

Bit 2: Channel side.

Allowed values:
0: Left: Channel left has to be transmitted or has been received
1: Right: Channel right has to be transmitted or has been received

UDR

Bit 3: Underrun flag.

Allowed values:
0: NoUnderrun: No underrun occurred
1: Underrun: Underrun occurred

CRCERR

Bit 4: CRC error flag.

Allowed values:
0: Match: CRC value received matches the SPIx_RXCRCR value
1: NoMatch: CRC value received does not match the SPIx_RXCRCR value

MODF

Bit 5: Mode fault.

Allowed values:
0: NoFault: No mode fault occurred
1: Fault: Mode fault occurred

OVR

Bit 6: Overrun flag.

Allowed values:
0: NoOverrun: No overrun occurred
1: Overrun: Overrun occurred

BSY

Bit 7: Busy flag.

Allowed values:
0: NotBusy: SPI not busy
1: Busy: SPI busy

FRE

Bit 8: TI frame format error.

Allowed values:
0: NoError: No frame format error
1: Error: A frame format error occurred

FRLVL

Bits 9-10: FIFO reception level.

Allowed values:
0: Empty: Rx FIFO Empty
1: Quarter: Rx 1/4 FIFO
2: Half: Rx 1/2 FIFO
3: Full: Rx FIFO full

FTLVL

Bits 11-12: FIFO transmission level.

Allowed values:
0: Empty: Tx FIFO Empty
1: Quarter: Tx 1/4 FIFO
2: Half: Tx 1/2 FIFO
3: Full: Tx FIFO full

DR

data register

Offset: 0xc, size: 16, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DR rw

Toggle fields

DR

Bits 0-15: Data register.

Allowed values: 0x0-0xffff

DR8

Direct 8-bit access to data register

Offset: 0xc, size: 8, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								DR rw

Toggle fields

DR

Bits 0-7: Data register.

Allowed values: 0x0-0xff

CRCPR

CRC polynomial register

Offset: 0x10, size: 16, reset: 0x00000007, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CRCPOLY rw

Toggle fields

CRCPOLY

Bits 0-15: CRC polynomial register.

Allowed values: 0x0-0xffff

RXCRCR

RX CRC register

Offset: 0x14, size: 16, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RxCRC r

Toggle fields

RxCRC

Bits 0-15: Rx CRC register.

Allowed values: 0x0-0xffff

TXCRCR

TX CRC register

Offset: 0x18, size: 16, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TxCRC r

Toggle fields

TxCRC

Bits 0-15: Tx CRC register.

Allowed values: 0x0-0xffff

I2SCFGR

I2S configuration register

Offset: 0x1c, size: 16, reset: 0x00000000, access: read-write

8/8 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				I2SMOD rw	I2SE rw	I2SCFG rw		PCMSYNC rw		I2SSTD rw		CKPOL rw	DATLEN rw		CHLEN rw

Toggle fields

CHLEN

Bit 0: Channel length (number of bits per audio channel).

Allowed values:
0: SixteenBit: 16-bit wide
1: ThirtyTwoBit: 32-bit wide

DATLEN

Bits 1-2: Data length to be transferred.

Allowed values:
0: SixteenBit: 16-bit data length
1: TwentyFourBit: 24-bit data length
2: ThirtyTwoBit: 32-bit data length

CKPOL

Bit 3: Steady state clock polarity.

Allowed values:
0: IdleLow: I2S clock inactive state is low level
1: IdleHigh: I2S clock inactive state is high level

I2SSTD

Bits 4-5: I2S standard selection.

Allowed values:
0: Philips: I2S Philips standard
1: MSB: MSB justified standard
2: LSB: LSB justified standard
3: PCM: PCM standard

PCMSYNC

Bit 7: PCM frame synchronization.

Allowed values:
0: Short: Short frame synchronisation
1: Long: Long frame synchronisation

I2SCFG

Bits 8-9: I2S configuration mode.

Allowed values:
0: SlaveTx: Slave - transmit
1: SlaveRx: Slave - receive
2: MasterTx: Master - transmit
3: MasterRx: Master - receive

I2SE

Bit 10: I2S Enable.

Allowed values:
0: Disabled: I2S peripheral is disabled
1: Enabled: I2S peripheral is enabled

I2SMOD

Bit 11: I2S mode selection.

Allowed values:
0: SPIMode: SPI mode is selected
1: I2SMode: I2S mode is selected

I2SPR

I2S prescaler register

Offset: 0x20, size: 16, reset: 0x00000010, access: read-write

3/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						MCKOE rw	ODD rw	I2SDIV rw

Toggle fields

I2SDIV

Bits 0-7: I2S Linear prescaler.

Allowed values: 0x2-0xff

ODD

Bit 8: Odd factor for the prescaler.

Allowed values:
0: Even: Real divider value is I2SDIV * 2
1: Odd: Real divider value is (I2SDIV * 2) + 1

MCKOE

Bit 9: Master clock output enable.

Allowed values:
0: Disabled: Master clock output is disabled
1: Enabled: Master clock output is enabled

IWDG

0x40003000: Independent watchdog

7/7 fields covered.

Toggle register map

Offset	Name	15	11	2	1	0
0x0	KR	KEY
0x4	PR			PR
0x8	RLR		RL
0xc	SR			WVU	RVU	PVU
0x10	WINR		WIN

Toggle registers

KR

Key register

Offset: 0x0, size: 32, reset: 0x00000000, access: write-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
KEY w

Toggle fields

KEY

Bits 0-15: Key value.

Allowed values:
21845: Unlock: Enable access to PR, RLR and WINR registers
43690: Feed: Feed watchdog with RLR register value
52428: Start: Start the watchdog

PR

Prescaler register

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
													PR rw

Toggle fields

PR

Bits 0-2: Prescaler divider.

Allowed values:
0: DivideBy4: Divider /4
1: DivideBy8: Divider /8
2: DivideBy16: Divider /16
3: DivideBy32: Divider /32
4: DivideBy64: Divider /64
5: DivideBy128: Divider /128
6: DivideBy256: Divider /256

RLR

Reload register

Offset: 0x8, size: 32, reset: 0x00000FFF, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				RL rw

Toggle fields

RL

Bits 0-11: Watchdog counter reload value.

Allowed values: 0x0-0xfff

SR

Status register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-only

3/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
													WVU r	RVU r	PVU r

Toggle fields

PVU

Bit 0: Watchdog prescaler value update.

RVU

Bit 1: Watchdog counter reload value update.

WVU

Bit 2: Watchdog counter window value update.

WINR

Window register

Offset: 0x10, size: 32, reset: 0x00000FFF, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				WIN rw

Toggle fields

WIN

Bits 0-11: Watchdog counter window value.

Allowed values: 0x0-0xfff

MPU

0xe000ed90: Memory protection unit

6/19 fields covered.

Toggle register map

Offset	Name	31	28	26	23	21	18	17	16	15	7	5	4	3	2	1	0
0x0	TYPER				IREGION					DREGION							SEPARATE
0x4	CTRL														PRIVDEFENA	HFNMIENA	ENABLE
0x8	RNR										REGION
0xc	RBAR	ADDR								ADDR			VALID	REGION
0x10	RASR		XN	AP		TEX	S	C	B	SRD		SIZE					ENABLE

Toggle registers

TYPER

MPU type register

Offset: 0x0, size: 32, reset: 0x00000800, access: read-only

3/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								IREGION r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DREGION r															SEPARATE r

Toggle fields

SEPARATE

Bit 0: Separate flag.

DREGION

Bits 8-15: Number of MPU data regions.

IREGION

Bits 16-23: Number of MPU instruction regions.

CTRL

MPU control register

Offset: 0x4, size: 32, reset: 0x00000000, access: read-only

3/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
													PRIVDEFENA r	HFNMIENA r	ENABLE r

Toggle fields

ENABLE

Bit 0: Enables the MPU.

HFNMIENA

Bit 1: Enables the operation of MPU during hard fault.

PRIVDEFENA

Bit 2: Enable priviliged software access to default memory map.

RNR

MPU region number register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								REGION rw

Toggle fields

REGION

Bits 0-7: MPU region.

RBAR

MPU region base address register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

0/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ADDR rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ADDR rw											VALID rw	REGION rw

Toggle fields

REGION

Bits 0-3: MPU region field.

VALID

Bit 4: MPU region number valid.

ADDR

Bits 5-31: Region base address field.

RASR

MPU region attribute and size register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

0/9 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
			XN rw		AP rw					TEX rw			S rw	C rw	B rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SRD rw										SIZE rw					ENABLE rw

Toggle fields

ENABLE

Bit 0: Region enable bit..

SIZE

Bits 1-5: Size of the MPU protection region.

SRD

Bits 8-15: Subregion disable bits.

B

Bit 16: memory attribute.

C

Bit 17: memory attribute.

S

Bit 18: Shareable memory attribute.

TEX

Bits 19-21: memory attribute.

AP

Bits 24-26: Access permission.

XN

Bit 28: Instruction access disable bit.

NVIC

0xe000e100: Nested Vectored Interrupt Controller

3/99 fields covered.

Toggle register map

Offset	Name	31	23	15	7
0x0	ISER0	SETENA		SETENA
0x4	ISER1	SETENA		SETENA
0x8	ISER2	SETENA		SETENA
0x80	ICER0	CLRENA		CLRENA
0x84	ICER1	CLRENA		CLRENA
0x88	ICER2	CLRENA		CLRENA
0x100	ISPR0	SETPEND		SETPEND
0x104	ISPR1	SETPEND		SETPEND
0x108	ISPR2	SETPEND		SETPEND
0x180	ICPR0	CLRPEND		CLRPEND
0x184	ICPR1	CLRPEND		CLRPEND
0x188	ICPR2	CLRPEND		CLRPEND
0x200	IABR0	ACTIVE		ACTIVE
0x204	IABR1	ACTIVE		ACTIVE
0x208	IABR2	ACTIVE		ACTIVE
0x300	IPR0	IPR_N3	IPR_N2	IPR_N1	IPR_N0
0x304	IPR1	IPR_N3	IPR_N2	IPR_N1	IPR_N0
0x308	IPR2	IPR_N3	IPR_N2	IPR_N1	IPR_N0
0x30c	IPR3	IPR_N3	IPR_N2	IPR_N1	IPR_N0
0x310	IPR4	IPR_N3	IPR_N2	IPR_N1	IPR_N0
0x314	IPR5	IPR_N3	IPR_N2	IPR_N1	IPR_N0
0x318	IPR6	IPR_N3	IPR_N2	IPR_N1	IPR_N0
0x31c	IPR7	IPR_N3	IPR_N2	IPR_N1	IPR_N0
0x320	IPR8	IPR_N3	IPR_N2	IPR_N1	IPR_N0
0x324	IPR9	IPR_N3	IPR_N2	IPR_N1	IPR_N0
0x328	IPR10	IPR_N3	IPR_N2	IPR_N1	IPR_N0
0x32c	IPR11	IPR_N3	IPR_N2	IPR_N1	IPR_N0
0x330	IPR12	IPR_N3	IPR_N2	IPR_N1	IPR_N0
0x334	IPR13	IPR_N3	IPR_N2	IPR_N1	IPR_N0
0x338	IPR14	IPR_N3	IPR_N2	IPR_N1	IPR_N0
0x33c	IPR15	IPR_N3	IPR_N2	IPR_N1	IPR_N0
0x340	IPR16	IPR_N3	IPR_N2	IPR_N1	IPR_N0
0x344	IPR17	IPR_N3	IPR_N2	IPR_N1	IPR_N0
0x348	IPR18	IPR_N3	IPR_N2	IPR_N1	IPR_N0
0x34c	IPR19	IPR_N3	IPR_N2	IPR_N1	IPR_N0
0x350	IPR20	IPR_N3	IPR_N2	IPR_N1	IPR_N0

Toggle registers

ISER0

Interrupt Set-Enable Register

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
SETENA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SETENA rw

Toggle fields

SETENA

Bits 0-31: SETENA.

ISER1

Interrupt Set-Enable Register

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
SETENA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SETENA rw

Toggle fields

SETENA

Bits 0-31: SETENA.

ISER2

Interrupt Set-Enable Register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
SETENA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SETENA rw

Toggle fields

SETENA

Bits 0-31: SETENA.

ICER0

Interrupt Clear-Enable Register

Offset: 0x80, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
CLRENA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CLRENA rw

Toggle fields

CLRENA

Bits 0-31: CLRENA.

ICER1

Interrupt Clear-Enable Register

Offset: 0x84, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
CLRENA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CLRENA rw

Toggle fields

CLRENA

Bits 0-31: CLRENA.

ICER2

Interrupt Clear-Enable Register

Offset: 0x88, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
CLRENA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CLRENA rw

Toggle fields

CLRENA

Bits 0-31: CLRENA.

ISPR0

Interrupt Set-Pending Register

Offset: 0x100, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
SETPEND rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SETPEND rw

Toggle fields

SETPEND

Bits 0-31: SETPEND.

ISPR1

Interrupt Set-Pending Register

Offset: 0x104, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
SETPEND rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SETPEND rw

Toggle fields

SETPEND

Bits 0-31: SETPEND.

ISPR2

Interrupt Set-Pending Register

Offset: 0x108, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
SETPEND rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SETPEND rw

Toggle fields

SETPEND

Bits 0-31: SETPEND.

ICPR0

Interrupt Clear-Pending Register

Offset: 0x180, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
CLRPEND rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CLRPEND rw

Toggle fields

CLRPEND

Bits 0-31: CLRPEND.

ICPR1

Interrupt Clear-Pending Register

Offset: 0x184, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
CLRPEND rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CLRPEND rw

Toggle fields

CLRPEND

Bits 0-31: CLRPEND.

ICPR2

Interrupt Clear-Pending Register

Offset: 0x188, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
CLRPEND rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CLRPEND rw

Toggle fields

CLRPEND

Bits 0-31: CLRPEND.

IABR0

Interrupt Active Bit Register

Offset: 0x200, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ACTIVE r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ACTIVE r

Toggle fields

ACTIVE

Bits 0-31: ACTIVE.

IABR1

Interrupt Active Bit Register

Offset: 0x204, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ACTIVE r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ACTIVE r

Toggle fields

ACTIVE

Bits 0-31: ACTIVE.

IABR2

Interrupt Active Bit Register

Offset: 0x208, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ACTIVE r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ACTIVE r

Toggle fields

ACTIVE

Bits 0-31: ACTIVE.

IPR0

Interrupt Priority Register

Offset: 0x300, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
IPR_N3 rw								IPR_N2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IPR_N1 rw								IPR_N0 rw

Toggle fields

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR1

Interrupt Priority Register

Offset: 0x304, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
IPR_N3 rw								IPR_N2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IPR_N1 rw								IPR_N0 rw

Toggle fields

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR2

Interrupt Priority Register

Offset: 0x308, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
IPR_N3 rw								IPR_N2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IPR_N1 rw								IPR_N0 rw

Toggle fields

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR3

Interrupt Priority Register

Offset: 0x30c, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
IPR_N3 rw								IPR_N2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IPR_N1 rw								IPR_N0 rw

Toggle fields

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR4

Interrupt Priority Register

Offset: 0x310, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
IPR_N3 rw								IPR_N2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IPR_N1 rw								IPR_N0 rw

Toggle fields

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR5

Interrupt Priority Register

Offset: 0x314, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
IPR_N3 rw								IPR_N2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IPR_N1 rw								IPR_N0 rw

Toggle fields

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR6

Interrupt Priority Register

Offset: 0x318, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
IPR_N3 rw								IPR_N2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IPR_N1 rw								IPR_N0 rw

Toggle fields

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR7

Interrupt Priority Register

Offset: 0x31c, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
IPR_N3 rw								IPR_N2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IPR_N1 rw								IPR_N0 rw

Toggle fields

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR8

Interrupt Priority Register

Offset: 0x320, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
IPR_N3 rw								IPR_N2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IPR_N1 rw								IPR_N0 rw

Toggle fields

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR9

Interrupt Priority Register

Offset: 0x324, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
IPR_N3 rw								IPR_N2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IPR_N1 rw								IPR_N0 rw

Toggle fields

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR10

Interrupt Priority Register

Offset: 0x328, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
IPR_N3 rw								IPR_N2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IPR_N1 rw								IPR_N0 rw

Toggle fields

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR11

Interrupt Priority Register

Offset: 0x32c, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
IPR_N3 rw								IPR_N2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IPR_N1 rw								IPR_N0 rw

Toggle fields

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR12

Interrupt Priority Register

Offset: 0x330, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
IPR_N3 rw								IPR_N2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IPR_N1 rw								IPR_N0 rw

Toggle fields

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR13

Interrupt Priority Register

Offset: 0x334, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
IPR_N3 rw								IPR_N2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IPR_N1 rw								IPR_N0 rw

Toggle fields

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR14

Interrupt Priority Register

Offset: 0x338, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
IPR_N3 rw								IPR_N2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IPR_N1 rw								IPR_N0 rw

Toggle fields

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR15

Interrupt Priority Register

Offset: 0x33c, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
IPR_N3 rw								IPR_N2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IPR_N1 rw								IPR_N0 rw

Toggle fields

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR16

Interrupt Priority Register

Offset: 0x340, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
IPR_N3 rw								IPR_N2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IPR_N1 rw								IPR_N0 rw

Toggle fields

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR17

Interrupt Priority Register

Offset: 0x344, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
IPR_N3 rw								IPR_N2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IPR_N1 rw								IPR_N0 rw

Toggle fields

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR18

Interrupt Priority Register

Offset: 0x348, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
IPR_N3 rw								IPR_N2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IPR_N1 rw								IPR_N0 rw

Toggle fields

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR19

Interrupt Priority Register

Offset: 0x34c, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
IPR_N3 rw								IPR_N2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IPR_N1 rw								IPR_N0 rw

Toggle fields

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

IPR20

Interrupt Priority Register

Offset: 0x350, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
IPR_N3 rw								IPR_N2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IPR_N1 rw								IPR_N0 rw

Toggle fields

IPR_N0

Bits 0-7: IPR_N0.

IPR_N1

Bits 8-15: IPR_N1.

IPR_N2

Bits 16-23: IPR_N2.

IPR_N3

Bits 24-31: IPR_N3.

NVIC_STIR

0xe000ef00: Nested vectored interrupt controller

0/1 fields covered.

Toggle register map

Offset	Name	31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	STIR																								INTID

Toggle registers

STIR

Software trigger interrupt register

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							INTID rw

Toggle fields

INTID

Bits 0-8: Software generated interrupt ID.

OPAMP

0x40010000: Operational Amplifier

19/64 fields covered.

Toggle register map

Offset	Name	31	30	29	28	23	18	17	15	13	11	10	8	7	6	3	1	0
0x38	OPAMP1_CSR	LOCK	OUTCAL	TSTREF	TRIMOFFSETN	TRIMOFFSETP	USER_TRIM	PGA_GAIN	PGA_GAIN	CALSEL	CALON	VPS_SEL	VMS_SEL	TCM_EN	VM_SEL	VP_SEL	FORCE_VP	OPAMP1EN
0x3c	OPAMP2_CSR	LOCK	OUTCAL	TSTREF	TRIMOFFSETN	TRIMOFFSETP	USER_TRIM	PGA_GAIN	PGA_GAIN	CALSEL	CALON	VPS_SEL	VMS_SEL	TCM_EN	VM_SEL	VP_SEL	FORCE_VP	OPAMP2EN
0x40	OPAMP3_CSR	LOCK	OUTCAL	TSTREF	TRIMOFFSETN	TRIMOFFSETP	USER_TRIM	PGA_GAIN	PGA_GAIN	CALSEL	CALON	VPS_SEL	VMS_SEL	TCM_EN	VM_SEL	VP_SEL	FORCE_VP	OPAMP3EN
0x44	OPAMP4_CSR	LOCK	OUTCAL	TSTREF	TRIMOFFSETN	TRIMOFFSETP	USER_TRIM	PGA_GAIN	PGA_GAIN	CALSEL	CALON	VPS_SEL	VMS_SEL	TCM_EN	VM_SEL	VP_SEL	FORCE_VP	OPAMP4EN

Toggle registers

OPAMP1_CSR

OPAMP1 control register

Offset: 0x38, size: 32, reset: 0x00000000, access: Unspecified

1/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
LOCK rw	OUTCAL r	TSTREF rw	TRIMOFFSETN rw					TRIMOFFSETP rw					USER_TRIM rw	PGA_GAIN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PGA_GAIN rw		CALSEL rw		CALON rw	VPS_SEL rw		VMS_SEL rw	TCM_EN rw	VM_SEL rw			VP_SEL rw		FORCE_VP rw	OPAMP1EN rw

Toggle fields

OPAMP1EN

Bit 0: OPAMP1 enable.

FORCE_VP

Bit 1: FORCE_VP.

VP_SEL

Bits 2-3: OPAMP Non inverting input selection.

VM_SEL

Bits 5-6: OPAMP inverting input selection.

TCM_EN

Bit 7: Timer controlled Mux mode enable.

VMS_SEL

Bit 8: OPAMP inverting input secondary selection.

VPS_SEL

Bits 9-10: OPAMP Non inverting input secondary selection.

CALON

Bit 11: Calibration mode enable.

CALSEL

Bits 12-13: Calibration selection.

PGA_GAIN

Bits 14-17: Gain in PGA mode.

USER_TRIM

Bit 18: User trimming enable.

TRIMOFFSETP

Bits 19-23: Offset trimming value (PMOS).

TRIMOFFSETN

Bits 24-28: Offset trimming value (NMOS).

TSTREF

Bit 29: TSTREF.

OUTCAL

Bit 30: OPAMP ouput status flag.

LOCK

Bit 31: OPAMP lock.

OPAMP2_CSR

OPAMP2 control register

Offset: 0x3c, size: 32, reset: 0x00000000, access: Unspecified

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
LOCK rw	OUTCAL r	TSTREF rw	TRIMOFFSETN rw					TRIMOFFSETP rw					USER_TRIM rw	PGA_GAIN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PGA_GAIN rw		CALSEL rw		CALON rw	VPS_SEL rw		VMS_SEL rw	TCM_EN rw	VM_SEL rw			VP_SEL rw		FORCE_VP rw	OPAMP2EN rw

Toggle fields

OPAMP2EN

Bit 0: OPAMP2 enable.

Allowed values:
0: Disabled: OPAMP2 is disabled
1: Enabled: OPAMP2 is enabled

FORCE_VP

Bit 1: FORCE_VP.

Allowed values:
0: Normal: Normal operating mode
1: Calibration: Calibration mode. Non-inverting input connected to calibration reference

VP_SEL

Bits 2-3: OPAMP Non inverting input selection.

Allowed values:
1: PB14: PB14 used as OPAMP2 non-inverting input
2: PB0: PB0 used as OPAMP2 non-inverting input
3: PA7: PA7 used as OPAMP2 non-inverting input

VM_SEL

Bits 5-6: OPAMP inverting input selection.

Allowed values:
0: PC5: PC5 (VM0) used as OPAMP2 inverting input
1: PA5: PA5 (VM1) used as OPAMP2 inverting input
2: PGA: Resistor feedback output (PGA mode)
3: Follower: Follower mode

TCM_EN

Bit 7: Timer controlled Mux mode enable.

Allowed values:
0: Disabled: Timer controlled mux disabled
1: Enabled: Timer controlled mux enabled

VMS_SEL

Bit 8: OPAMP inverting input secondary selection.

Allowed values:
0: PC5: PC5 (VM0) used as OPAMP2 inverting input when TCM_EN=1
1: PA5: PA5 (VM1) used as OPAMP2 inverting input when TCM_EN=1

VPS_SEL

Bits 9-10: OPAMP Non inverting input secondary selection.

Allowed values:
1: PB14: PB14 used as OPAMP2 non-inverting input when TCM_EN=1
2: PB0: PB0 used as OPAMP2 non-inverting input when TCM_EN=1
3: PA7: PA7 used as OPAMP2 non-inverting input when TCM_EN=1

CALON

Bit 11: Calibration mode enable.

Allowed values:
0: Disabled: Calibration mode disabled
1: Enabled: Calibration mode enabled

CALSEL

Bits 12-13: Calibration selection.

Allowed values:
0: Percent3_3: VREFOPAMP=3.3% VDDA
1: Percent10: VREFOPAMP=10% VDDA
2: Percent50: VREFOPAMP=50% VDDA
3: Percent90: VREFOPAMP=90% VDDA

PGA_GAIN

Bits 14-17: Gain in PGA mode.

Allowed values:
0: Gain2: Gain 2
1: Gain4: Gain 4
2: Gain8: Gain 8
4: Gain16: Gain 16
8: Gain2_VM0: Gain 2, feedback connected to VM0
9: Gain4_VM0: Gain 4, feedback connected to VM0
10: Gain8_VM0: Gain 8, feedback connected to VM0
11: Gain16_VM0: Gain 16, feedback connected to VM0
12: Gain2_VM1: Gain 2, feedback connected to VM1
13: Gain4_VM1: Gain 4, feedback connected to VM1
14: Gain8_VM1: Gain 8, feedback connected to VM1
15: Gain16_VM1: Gain 16, feedback connected to VM1

USER_TRIM

Bit 18: User trimming enable.

Allowed values:
0: Disabled: User trimming disabled
1: Enabled: User trimming enabled

TRIMOFFSETP

Bits 19-23: Offset trimming value (PMOS).

Allowed values: 0x0-0x1f

TRIMOFFSETN

Bits 24-28: Offset trimming value (NMOS).

Allowed values: 0x0-0x1f

TSTREF

Bit 29: TSTREF.

Allowed values:
0: Output: VREFOPAMP2 is output
1: NotOutput: VREFOPAMP2 is not output

OUTCAL

Bit 30: OPAMP ouput status flag.

Allowed values:
0: Low: Non-inverting < inverting
1: High: Non-inverting > inverting

LOCK

Bit 31: OPAMP lock.

Allowed values:
0: Unlocked: Comparator CSR bits are read-write
1: Locked: Comparator CSR bits are read-only

OPAMP3_CSR

OPAMP3 control register

Offset: 0x40, size: 32, reset: 0x00000000, access: Unspecified

1/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
LOCK rw	OUTCAL r	TSTREF rw	TRIMOFFSETN rw					TRIMOFFSETP rw					USER_TRIM rw	PGA_GAIN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PGA_GAIN rw		CALSEL rw		CALON rw	VPS_SEL rw		VMS_SEL rw	TCM_EN rw	VM_SEL rw			VP_SEL rw		FORCE_VP rw	OPAMP3EN rw

Toggle fields

OPAMP3EN

Bit 0: OPAMP3 enable.

FORCE_VP

Bit 1: FORCE_VP.

VP_SEL

Bits 2-3: OPAMP Non inverting input selection.

VM_SEL

Bits 5-6: OPAMP inverting input selection.

TCM_EN

Bit 7: Timer controlled Mux mode enable.

VMS_SEL

Bit 8: OPAMP inverting input secondary selection.

VPS_SEL

Bits 9-10: OPAMP Non inverting input secondary selection.

CALON

Bit 11: Calibration mode enable.

CALSEL

Bits 12-13: Calibration selection.

PGA_GAIN

Bits 14-17: Gain in PGA mode.

USER_TRIM

Bit 18: User trimming enable.

TRIMOFFSETP

Bits 19-23: Offset trimming value (PMOS).

TRIMOFFSETN

Bits 24-28: Offset trimming value (NMOS).

TSTREF

Bit 29: TSTREF.

OUTCAL

Bit 30: OPAMP ouput status flag.

LOCK

Bit 31: OPAMP lock.

OPAMP4_CSR

OPAMP4 control register

Offset: 0x44, size: 32, reset: 0x00000000, access: Unspecified

1/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
LOCK rw	OUTCAL r	TSTREF rw	TRIMOFFSETN rw					TRIMOFFSETP rw					USER_TRIM rw	PGA_GAIN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PGA_GAIN rw		CALSEL rw		CALON rw	VPS_SEL rw		VMS_SEL rw	TCM_EN rw	VM_SEL rw			VP_SEL rw		FORCE_VP rw	OPAMP4EN rw

Toggle fields

OPAMP4EN

Bit 0: OPAMP4 enable.

FORCE_VP

Bit 1: FORCE_VP.

VP_SEL

Bits 2-3: OPAMP Non inverting input selection.

VM_SEL

Bits 5-6: OPAMP inverting input selection.

TCM_EN

Bit 7: Timer controlled Mux mode enable.

VMS_SEL

Bit 8: OPAMP inverting input secondary selection.

VPS_SEL

Bits 9-10: OPAMP Non inverting input secondary selection.

CALON

Bit 11: Calibration mode enable.

CALSEL

Bits 12-13: Calibration selection.

PGA_GAIN

Bits 14-17: Gain in PGA mode.

USER_TRIM

Bit 18: User trimming enable.

TRIMOFFSETP

Bits 19-23: Offset trimming value (PMOS).

TRIMOFFSETN

Bits 24-28: Offset trimming value (NMOS).

TSTREF

Bit 29: TSTREF.

OUTCAL

Bit 30: OPAMP ouput status flag.

LOCK

Bit 31: OPAMP lock.

PWR

0x40007000: Power control

5/14 fields covered.

Toggle register map

Offset	Name	31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	CR																								DBP	PLS			PVDE	CSBF	CWUF	PDDS	LPDS
0x4	CSR																						EWUP3	EWUP2	EWUP1					VREFINTRDYF	PVDO	SBF	WUF

Toggle registers

CR

power control register

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

1/7 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							DBP rw	PLS rw			PVDE rw	CSBF rw	CWUF rw	PDDS rw	LPDS rw

Toggle fields

LPDS

Bit 0: Low-power deep sleep.

PDDS

Bit 1: Power down deepsleep.

Allowed values:
0: STOP_MODE: Enter Stop mode when the CPU enters deepsleep
1: STANDBY_MODE: Enter Standby mode when the CPU enters deepsleep

CWUF

Bit 2: Clear wakeup flag.

CSBF

Bit 3: Clear standby flag.

PVDE

Bit 4: Power voltage detector enable.

PLS

Bits 5-7: PVD level selection.

DBP

Bit 8: Disable backup domain write protection.

CSR

power control/status register

Offset: 0x4, size: 32, reset: 0x00000000, access: Unspecified

4/7 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
					EWUP3 rw	EWUP2 rw	EWUP1 rw					VREFINTRDYF r	PVDO r	SBF r	WUF r

Toggle fields

WUF

Bit 0: Wakeup flag.

SBF

Bit 1: Standby flag.

PVDO

Bit 2: PVD output.

VREFINTRDYF

Bit 3: Internal voltage reference ready flag.

EWUP1

Bit 8: Enable WKUP1 pin.

EWUP2

Bit 9: Enable WKUP2 pin.

EWUP3

Bit 10: Enable WKUP3 pin.

RCC

0x40021000: Reset and clock control

166/166 fields covered.

Toggle register map

Offset	Name	31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	CR							PLLRDY	PLLON					CSSON	HSEBYP	HSERDY	HSEON	HSICAL								HSITRIM						HSIRDY	HSION
0x4	CFGR	PLLNODIV	MCOPRE				MCO			I2SSRC	USBPRE	PLLMUL				PLLXTPRE	PLLSRC	PLLSRC		PPRE2			PPRE1			HPRE				SWS		SW
0x8	CIR									CSSC			PLLRDYC	HSERDYC	HSIRDYC	LSERDYC	LSIRDYC				PLLRDYIE	HSERDYIE	HSIRDYIE	LSERDYIE	LSIRDYIE	CSSF			PLLRDYF	HSERDYF	HSIRDYF	LSERDYF	LSIRDYF
0xc	APB2RSTR												TIM20RST		TIM17RST	TIM16RST	TIM15RST	SPI4RST	USART1RST	TIM8RST	SPI1RST	TIM1RST											SYSCFGRST
0x10	APB1RSTR		I2C3RST	DAC1RST	PWRRST		DAC2RST	CANRST		USBRST	I2C2RST	I2C1RST	UART5RST	UART4RST	USART3RST	USART2RST		SPI3RST	SPI2RST			WWDGRST						TIM7RST	TIM6RST		TIM4RST	TIM3RST	TIM2RST
0x14	AHBENR			ADC34EN	ADC12EN				TSCEN	IOPGEN	IOPFEN	IOPEEN	IOPDEN	IOPCEN	IOPBEN	IOPAEN	IOPHEN										CRCEN	FMCEN	FLITFEN		SRAMEN	DMA2EN	DMA1EN
0x18	APB2ENR												TIM20EN		TIM17EN	TIM16EN	TIM15EN	SPI4EN	USART1EN	TIM8EN	SPI1EN	TIM1EN											SYSCFGEN
0x1c	APB1ENR		I2C3EN	DAC1EN	PWREN		DAC2EN	CANEN		USBEN	I2C2EN	I2C1EN	UART5EN	UART4EN	USART3EN	USART2EN		SPI3EN	SPI2EN			WWDGEN						TIM7EN	TIM6EN		TIM4EN	TIM3EN	TIM2EN
0x20	BDCR																BDRST	RTCEN						RTCSEL					LSEDRV		LSEBYP	LSERDY	LSEON
0x24	CSR	LPWRRSTF	WWDGRSTF	IWDGRSTF	SFTRSTF	PORRSTF	PINRSTF	OBLRSTF	RMVF	V18PWRRSTF																						LSIRDY	LSION
0x28	AHBRSTR			ADC34RST	ADC12RST				TSCRST	IOPGRST	IOPFRST	IOPERST	IOPDRST	IOPCRST	IOPBRST	IOPARST	IOPHRST											FMCRST
0x2c	CFGR2																			ADC34PRES					ADC12PRES					PREDIV
0x30	CFGR3							TIM34SW	TIM2SW	UART5SW		UART4SW		USART3SW		USART2SW		TIM20SW		TIM17SW		TIM16SW	TIM15SW	TIM8SW	TIM1SW		I2C3SW	I2C2SW	I2C1SW			USART1SW

Toggle registers

CR

Clock control register

Offset: 0x0, size: 32, reset: 0x00000083, access: Unspecified

10/10 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
						PLLRDY r	PLLON rw					CSSON rw	HSEBYP rw	HSERDY r	HSEON rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
HSICAL r								HSITRIM rw						HSIRDY r	HSION rw

Toggle fields

HSION

Bit 0: Internal High Speed clock enable.

Allowed values:
0: Off: Clock Off
1: On: Clock On

HSIRDY

Bit 1: Internal High Speed clock ready flag.

Allowed values:
0: NotReady: Clock not ready
1: Ready: Clock ready

HSITRIM

Bits 3-7: Internal High Speed clock trimming.

Allowed values: 0x0-0x1f

HSICAL

Bits 8-15: Internal High Speed clock Calibration.

Allowed values: 0x0-0xff

HSEON

Bit 16: External High Speed clock enable.

Allowed values:
0: Off: Clock Off
1: On: Clock On

HSERDY

Bit 17: External High Speed clock ready flag.

Allowed values:
0: NotReady: Clock not ready
1: Ready: Clock ready

HSEBYP

Bit 18: External High Speed clock Bypass.

Allowed values:
0: NotBypassed: HSE crystal oscillator not bypassed
1: Bypassed: HSE crystal oscillator bypassed with external clock

CSSON

Bit 19: Clock Security System enable.

Allowed values:
0: Off: Clock security system disabled (clock detector OFF)
1: On: Clock security system enable (clock detector ON if the HSE is ready, OFF if not)

PLLON

Bit 24: PLL enable.

Allowed values:
0: Off: Clock Off
1: On: Clock On

PLLRDY

Bit 25: PLL clock ready flag.

Allowed values:
0: NotReady: Clock not ready
1: Ready: Clock ready

CFGR

Clock configuration register (RCC_CFGR)

Offset: 0x4, size: 32, reset: 0x00000000, access: Unspecified

13/13 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PLLNODIV N/A	MCOPRE N/A				MCO rw			I2SSRC rw	USBPRE rw	PLLMUL rw				PLLXTPRE rw	PLLSRC rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PLLSRC rw		PPRE2 rw			PPRE1 rw			HPRE rw				SWS r		SW rw

Toggle fields

SW

Bits 0-1: System clock Switch.

Allowed values:
0: HSI: HSI selected as system clock
1: HSE: HSE selected as system clock
2: PLL: PLL selected as system clock

SWS

Bits 2-3: System Clock Switch Status.

Allowed values:
0: HSI: HSI oscillator used as system clock
1: HSE: HSE oscillator used as system clock
2: PLL: PLL used as system clock

HPRE

Bits 4-7: AHB prescaler.

Allowed values:
8: Div2: SYSCLK divided by 2
9: Div4: SYSCLK divided by 4
10: Div8: SYSCLK divided by 8
11: Div16: SYSCLK divided by 16
12: Div64: SYSCLK divided by 64
13: Div128: SYSCLK divided by 128
14: Div256: SYSCLK divided by 256
15: Div512: SYSCLK divided by 512
0 (+): Div1: SYSCLK not divided

PPRE1

Bits 8-10: APB Low speed prescaler (APB1).

Allowed values:
4: Div2: HCLK divided by 2
5: Div4: HCLK divided by 4
6: Div8: HCLK divided by 8
7: Div16: HCLK divided by 16
0 (+): Div1: HCLK not divided

PPRE2

Bits 11-13: APB high speed prescaler (APB2).

Allowed values:
4: Div2: HCLK divided by 2
5: Div4: HCLK divided by 4
6: Div8: HCLK divided by 8
7: Div16: HCLK divided by 16
0 (+): Div1: HCLK not divided

PLLSRC

Bits 15-16: PLL entry clock source.

Allowed values:
0: HSI_Div2: HSI divided by 2 selected as PLL input clock
1: HSI_Div_PREDIV: HSI divided by PREDIV selected as PLL input clock
2: HSE_Div_PREDIV: HSE divided by PREDIV selected as PLL input clock

PLLXTPRE

Bit 17: HSE divider for PLL entry.

Allowed values:
0: Div1: HSE clock not divided
1: Div2: HSE clock divided by 2

PLLMUL

Bits 18-21: PLL Multiplication Factor.

Allowed values:
0: Mul2: PLL input clock x2
1: Mul3: PLL input clock x3
2: Mul4: PLL input clock x4
3: Mul5: PLL input clock x5
4: Mul6: PLL input clock x6
5: Mul7: PLL input clock x7
6: Mul8: PLL input clock x8
7: Mul9: PLL input clock x9
8: Mul10: PLL input clock x10
9: Mul11: PLL input clock x11
10: Mul12: PLL input clock x12
11: Mul13: PLL input clock x13
12: Mul14: PLL input clock x14
13: Mul15: PLL input clock x15
14: Mul16: PLL input clock x16
15: Mul16x: PLL input clock x16

USBPRE

Bit 22: USB prescaler.

Allowed values:
0: DIV1_5: PLL clock is divided by 1.5
1: DIV1: PLL clock is not divided

I2SSRC

Bit 23: I2S external clock source selection.

Allowed values:
0: SYSCLK: System clock used as I2S clock source
1: CKIN: External clock mapped on the I2S_CKIN pin used as I2S clock source

MCO

Bits 24-26: Microcontroller clock output.

Allowed values:
0: NoMCO: MCO output disabled, no clock on MCO
2: LSI: Internal low speed (LSI) oscillator clock selected
3: LSE: External low speed (LSE) oscillator clock selected
4: SYSCLK: System clock selected
5: HSI: Internal RC 8 MHz (HSI) oscillator clock selected
6: HSE: External 4-32 MHz (HSE) oscillator clock selected
7: PLL: PLL clock selected (divided by 1 or 2, depending en PLLNODIV)

MCOPRE

Bits 28-30: Microcontroller Clock Output Prescaler.

Allowed values:
0: Div1: MCO is divided by 1
1: Div2: MCO is divided by 2
2: Div4: MCO is divided by 4
3: Div8: MCO is divided by 8
4: Div16: MCO is divided by 16
5: Div32: MCO is divided by 32
6: Div64: MCO is divided by 64
7: Div128: MCO is divided by 128

PLLNODIV

Bit 31: Do not divide PLL to MCO.

Allowed values:
0: Div2: PLL is divided by 2 for MCO
1: Div1: PLL is not divided for MCO

CIR

Clock interrupt register (RCC_CIR)

Offset: 0x8, size: 32, reset: 0x00000000, access: Unspecified

17/17 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								CSSC w			PLLRDYC w	HSERDYC w	HSIRDYC w	LSERDYC w	LSIRDYC w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			PLLRDYIE rw	HSERDYIE rw	HSIRDYIE rw	LSERDYIE rw	LSIRDYIE rw	CSSF r			PLLRDYF r	HSERDYF r	HSIRDYF r	LSERDYF r	LSIRDYF r

Toggle fields

LSIRDYF

Bit 0: LSI Ready Interrupt flag.

Allowed values:
0: NotInterrupted: No clock ready interrupt
1: Interrupted: Clock ready interrupt

LSERDYF

Bit 1: LSE Ready Interrupt flag.

Allowed values:
0: NotInterrupted: No clock ready interrupt
1: Interrupted: Clock ready interrupt

HSIRDYF

Bit 2: HSI Ready Interrupt flag.

Allowed values:
0: NotInterrupted: No clock ready interrupt
1: Interrupted: Clock ready interrupt

HSERDYF

Bit 3: HSE Ready Interrupt flag.

Allowed values:
0: NotInterrupted: No clock ready interrupt
1: Interrupted: Clock ready interrupt

PLLRDYF

Bit 4: PLL Ready Interrupt flag.

Allowed values:
0: NotInterrupted: No clock ready interrupt
1: Interrupted: Clock ready interrupt

CSSF

Bit 7: Clock Security System Interrupt flag.

Allowed values:
0: NotInterrupted: No clock security interrupt caused by HSE clock failure
1: Interrupted: Clock security interrupt caused by HSE clock failure

LSIRDYIE

Bit 8: LSI Ready Interrupt Enable.

Allowed values:
0: Disabled: Interrupt disabled
1: Enabled: Interrupt enabled

LSERDYIE

Bit 9: LSE Ready Interrupt Enable.

Allowed values:
0: Disabled: Interrupt disabled
1: Enabled: Interrupt enabled

HSIRDYIE

Bit 10: HSI Ready Interrupt Enable.

Allowed values:
0: Disabled: Interrupt disabled
1: Enabled: Interrupt enabled

HSERDYIE

Bit 11: HSE Ready Interrupt Enable.

Allowed values:
0: Disabled: Interrupt disabled
1: Enabled: Interrupt enabled

PLLRDYIE

Bit 12: PLL Ready Interrupt Enable.

Allowed values:
0: Disabled: Interrupt disabled
1: Enabled: Interrupt enabled

LSIRDYC

Bit 16: LSI Ready Interrupt Clear.

Allowed values:
1: Clear: Clear interrupt flag

LSERDYC

Bit 17: LSE Ready Interrupt Clear.

Allowed values:
1: Clear: Clear interrupt flag

HSIRDYC

Bit 18: HSI Ready Interrupt Clear.

Allowed values:
1: Clear: Clear interrupt flag

HSERDYC

Bit 19: HSE Ready Interrupt Clear.

Allowed values:
1: Clear: Clear interrupt flag

PLLRDYC

Bit 20: PLL Ready Interrupt Clear.

Allowed values:
1: Clear: Clear interrupt flag

CSSC

Bit 23: Clock security system interrupt clear.

Allowed values:
1: Clear: Clear CSSF flag

APB2RSTR

APB2 peripheral reset register (RCC_APB2RSTR)

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

10/10 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
											TIM20RST rw		TIM17RST rw	TIM16RST rw	TIM15RST rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SPI4RST rw	USART1RST rw	TIM8RST rw	SPI1RST rw	TIM1RST rw											SYSCFGRST rw

Toggle fields

SYSCFGRST

Bit 0: SYSCFG and COMP reset.

Allowed values:
1: Reset: Reset the selected module

TIM1RST

Bit 11: TIM1 timer reset.

Allowed values:
1: Reset: Reset the selected module

SPI1RST

Bit 12: SPI 1 reset.

Allowed values:
1: Reset: Reset the selected module

TIM8RST

Bit 13: TIM8 timer reset.

Allowed values:
1: Reset: Reset the selected module

USART1RST

Bit 14: USART1 reset.

Allowed values:
1: Reset: Reset the selected module

SPI4RST

Bit 15: SPI4 reset.

Allowed values:
1: Reset: Reset the selected module

TIM15RST

Bit 16: TIM15 timer reset.

Allowed values:
1: Reset: Reset the selected module

TIM16RST

Bit 17: TIM16 timer reset.

Allowed values:
1: Reset: Reset the selected module

TIM17RST

Bit 18: TIM17 timer reset.

Allowed values:
1: Reset: Reset the selected module

TIM20RST

Bit 20: TIM20 timer reset.

Allowed values:
1: Reset: Reset the selected module

APB1RSTR

APB1 peripheral reset register (RCC_APB1RSTR)

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

20/20 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
	I2C3RST rw	DAC1RST rw	PWRRST rw		DAC2RST rw	CANRST rw		USBRST rw	I2C2RST rw	I2C1RST rw	UART5RST rw	UART4RST rw	USART3RST rw	USART2RST rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SPI3RST rw	SPI2RST rw			WWDGRST rw						TIM7RST rw	TIM6RST rw		TIM4RST rw	TIM3RST rw	TIM2RST rw

Toggle fields

TIM2RST

Bit 0: Timer 2 reset.

Allowed values:
1: Reset: Reset the selected module

TIM3RST

Bit 1: Timer 3 reset.

Allowed values:
1: Reset: Reset the selected module

TIM4RST

Bit 2: Timer 14 reset.

Allowed values:
1: Reset: Reset the selected module

TIM6RST

Bit 4: Timer 6 reset.

Allowed values:
1: Reset: Reset the selected module

TIM7RST

Bit 5: Timer 7 reset.

Allowed values:
1: Reset: Reset the selected module

WWDGRST

Bit 11: Window watchdog reset.

Allowed values:
1: Reset: Reset the selected module

SPI2RST

Bit 14: SPI2 reset.

Allowed values:
1: Reset: Reset the selected module

SPI3RST

Bit 15: SPI3 reset.

Allowed values:
1: Reset: Reset the selected module

USART2RST

Bit 17: USART 2 reset.

Allowed values:
1: Reset: Reset the selected module

USART3RST

Bit 18: USART3 reset.

Allowed values:
1: Reset: Reset the selected module

UART4RST

Bit 19: UART 4 reset.

Allowed values:
1: Reset: Reset the selected module

UART5RST

Bit 20: UART 5 reset.

Allowed values:
1: Reset: Reset the selected module

I2C1RST

Bit 21: I2C1 reset.

Allowed values:
1: Reset: Reset the selected module

I2C2RST

Bit 22: I2C2 reset.

Allowed values:
1: Reset: Reset the selected module

USBRST

Bit 23: USB reset.

Allowed values:
1: Reset: Reset the selected module

CANRST

Bit 25: CAN reset.

Allowed values:
1: Reset: Reset the selected module

DAC2RST

Bit 26: DAC2 interface reset.

Allowed values:
1: Reset: Reset the selected module

PWRRST

Bit 28: Power interface reset.

Allowed values:
1: Reset: Reset the selected module

DAC1RST

Bit 29: DAC interface reset.

Allowed values:
1: Reset: Reset the selected module

I2C3RST

Bit 30: I2C3 reset.

Allowed values:
1: Reset: Reset the selected module

AHBENR

AHB Peripheral Clock enable register (RCC_AHBENR)

Offset: 0x14, size: 32, reset: 0x00000014, access: read-write

17/17 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
		ADC34EN rw	ADC12EN rw				TSCEN rw	IOPGEN rw	IOPFEN rw	IOPEEN rw	IOPDEN rw	IOPCEN rw	IOPBEN rw	IOPAEN rw	IOPHEN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
									CRCEN rw	FMCEN rw	FLITFEN rw		SRAMEN rw	DMA2EN rw	DMA1EN rw

Toggle fields

DMA1EN

Bit 0: DMA1 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

DMA2EN

Bit 1: DMA2 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

SRAMEN

Bit 2: SRAM interface clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

FLITFEN

Bit 4: FLITF clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

FMCEN

Bit 5: FMC clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

CRCEN

Bit 6: CRC clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

IOPHEN

Bit 16: IO port H clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

IOPAEN

Bit 17: I/O port A clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

IOPBEN

Bit 18: I/O port B clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

IOPCEN

Bit 19: I/O port C clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

IOPDEN

Bit 20: I/O port D clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

IOPEEN

Bit 21: I/O port E clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

IOPFEN

Bit 22: I/O port F clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

IOPGEN

Bit 23: I/O port G clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

TSCEN

Bit 24: Touch sensing controller clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

ADC12EN

Bit 28: ADC1 and ADC2 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

ADC34EN

Bit 29: ADC3 and ADC4 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

APB2ENR

APB2 peripheral clock enable register (RCC_APB2ENR)

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

10/10 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
											TIM20EN rw		TIM17EN rw	TIM16EN rw	TIM15EN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SPI4EN rw	USART1EN rw	TIM8EN rw	SPI1EN rw	TIM1EN rw											SYSCFGEN rw

Toggle fields

SYSCFGEN

Bit 0: SYSCFG clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

TIM1EN

Bit 11: TIM1 Timer clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

SPI1EN

Bit 12: SPI 1 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

TIM8EN

Bit 13: TIM8 Timer clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

USART1EN

Bit 14: USART1 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

SPI4EN

Bit 15: SPI4 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

TIM15EN

Bit 16: TIM15 timer clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

TIM16EN

Bit 17: TIM16 timer clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

TIM17EN

Bit 18: TIM17 timer clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

TIM20EN

Bit 20: TIM20 timer clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

APB1ENR

APB1 peripheral clock enable register (RCC_APB1ENR)

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

20/20 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
	I2C3EN rw	DAC1EN rw	PWREN rw		DAC2EN rw	CANEN rw		USBEN rw	I2C2EN rw	I2C1EN rw	UART5EN rw	UART4EN rw	USART3EN rw	USART2EN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SPI3EN rw	SPI2EN rw			WWDGEN rw						TIM7EN rw	TIM6EN rw		TIM4EN rw	TIM3EN rw	TIM2EN rw

Toggle fields

TIM2EN

Bit 0: Timer 2 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

TIM3EN

Bit 1: Timer 3 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

TIM4EN

Bit 2: Timer 4 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

TIM6EN

Bit 4: Timer 6 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

TIM7EN

Bit 5: Timer 7 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

WWDGEN

Bit 11: Window watchdog clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

SPI2EN

Bit 14: SPI 2 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

SPI3EN

Bit 15: SPI 3 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

USART2EN

Bit 17: USART 2 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

USART3EN

Bit 18: USART 3 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

UART4EN

Bit 19: USART 4 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

UART5EN

Bit 20: USART 5 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

I2C1EN

Bit 21: I2C 1 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

I2C2EN

Bit 22: I2C 2 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

USBEN

Bit 23: USB clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

CANEN

Bit 25: CAN clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

DAC2EN

Bit 26: DAC2 interface clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

PWREN

Bit 28: Power interface clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

DAC1EN

Bit 29: DAC interface clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

I2C3EN

Bit 30: I2C3 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

BDCR

Backup domain control register (RCC_BDCR)

Offset: 0x20, size: 32, reset: 0x00000000, access: Unspecified

7/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															BDRST rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RTCEN rw						RTCSEL rw					LSEDRV rw		LSEBYP rw	LSERDY r	LSEON rw

Toggle fields

LSEON

Bit 0: External Low Speed oscillator enable.

Allowed values:
0: Off: LSE oscillator Off
1: On: LSE oscillator On

LSERDY

Bit 1: External Low Speed oscillator ready.

Allowed values:
0: NotReady: LSE oscillator not ready
1: Ready: LSE oscillator ready

LSEBYP

Bit 2: External Low Speed oscillator bypass.

Allowed values:
0: NotBypassed: LSE crystal oscillator not bypassed
1: Bypassed: LSE crystal oscillator bypassed with external clock

LSEDRV

Bits 3-4: LSE oscillator drive capability.

Allowed values:
0: Low: Low drive capacity
1: MediumHigh: Medium-high drive capacity
2: MediumLow: Medium-low drive capacity
3: High: High drive capacity

RTCSEL

Bits 8-9: RTC clock source selection.

Allowed values:
0: NoClock: No clock
1: LSE: LSE oscillator clock used as RTC clock
2: LSI: LSI oscillator clock used as RTC clock
3: HSE: HSE oscillator clock divided by a prescaler used as RTC clock

RTCEN

Bit 15: RTC clock enable.

Allowed values:
0: Disabled: RTC clock disabled
1: Enabled: RTC clock enabled

BDRST

Bit 16: Backup domain software reset.

Allowed values:
0: Disabled: Reset not activated
1: Enabled: Reset the entire RTC domain

CSR

Control/status register (RCC_CSR)

Offset: 0x24, size: 32, reset: 0x0C000000, access: Unspecified

11/11 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
LPWRRSTF rw	WWDGRSTF rw	IWDGRSTF rw	SFTRSTF rw	PORRSTF rw	PINRSTF rw	OBLRSTF rw	RMVF rw	V18PWRRSTF N/A
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														LSIRDY r	LSION rw

Toggle fields

LSION

Bit 0: Internal low speed oscillator enable.

Allowed values:
0: Off: LSI oscillator Off
1: On: LSI oscillator On

LSIRDY

Bit 1: Internal low speed oscillator ready.

Allowed values:
0: NotReady: LSI oscillator not ready
1: Ready: LSI oscillator ready

V18PWRRSTF

Bit 23: Reset flag of the 1.8 V domain.

Allowed values:
0: NoReset: No reset has occured
1: Reset: A reset has occured

RMVF

Bit 24: Remove reset flag.

Allowed values:
1: Clear: Clears the reset flag

OBLRSTF

Bit 25: Option byte loader reset flag.

Allowed values:
0: NoReset: No reset has occured
1: Reset: A reset has occured

PINRSTF

Bit 26: PIN reset flag.

Allowed values:
0: NoReset: No reset has occured
1: Reset: A reset has occured

PORRSTF

Bit 27: POR/PDR reset flag.

Allowed values:
0: NoReset: No reset has occured
1: Reset: A reset has occured

SFTRSTF

Bit 28: Software reset flag.

Allowed values:
0: NoReset: No reset has occured
1: Reset: A reset has occured

IWDGRSTF

Bit 29: Independent watchdog reset flag.

Allowed values:
0: NoReset: No reset has occured
1: Reset: A reset has occured

WWDGRSTF

Bit 30: Window watchdog reset flag.

Allowed values:
0: NoReset: No reset has occured
1: Reset: A reset has occured

LPWRRSTF

Bit 31: Low-power reset flag.

Allowed values:
0: NoReset: No reset has occured
1: Reset: A reset has occured

AHBRSTR

AHB peripheral reset register

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

12/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
		ADC34RST rw	ADC12RST rw				TSCRST rw	IOPGRST rw	IOPFRST rw	IOPERST rw	IOPDRST rw	IOPCRST rw	IOPBRST rw	IOPARST rw	IOPHRST rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
										FMCRST rw

Toggle fields

FMCRST

Bit 5: FMC reset.

Allowed values:
1: Reset: Reset the selected module

IOPHRST

Bit 16: I/O port H reset.

Allowed values:
1: Reset: Reset the selected module

IOPARST

Bit 17: I/O port A reset.

Allowed values:
1: Reset: Reset the selected module

IOPBRST

Bit 18: I/O port B reset.

Allowed values:
1: Reset: Reset the selected module

IOPCRST

Bit 19: I/O port C reset.

Allowed values:
1: Reset: Reset the selected module

IOPDRST

Bit 20: I/O port D reset.

Allowed values:
1: Reset: Reset the selected module

IOPERST

Bit 21: I/O port E reset.

Allowed values:
1: Reset: Reset the selected module

IOPFRST

Bit 22: I/O port F reset.

Allowed values:
1: Reset: Reset the selected module

IOPGRST

Bit 23: Touch sensing controller reset.

Allowed values:
1: Reset: Reset the selected module

TSCRST

Bit 24: Touch sensing controller reset.

Allowed values:
1: Reset: Reset the selected module

ADC12RST

Bit 28: ADC1 and ADC2 reset.

Allowed values:
1: Reset: Reset the selected module

ADC34RST

Bit 29: ADC3 and ADC4 reset.

Allowed values:
1: Reset: Reset the selected module

CFGR2

Clock configuration register 2

Offset: 0x2c, size: 32, reset: 0x00000000, access: read-write

3/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		ADC34PRES rw					ADC12PRES rw					PREDIV rw

Toggle fields

PREDIV

Bits 0-3: PREDIV division factor.

Allowed values:
0: Div1: PREDIV input clock not divided
1: Div2: PREDIV input clock divided by 2
2: Div3: PREDIV input clock divided by 3
3: Div4: PREDIV input clock divided by 4
4: Div5: PREDIV input clock divided by 5
5: Div6: PREDIV input clock divided by 6
6: Div7: PREDIV input clock divided by 7
7: Div8: PREDIV input clock divided by 8
8: Div9: PREDIV input clock divided by 9
9: Div10: PREDIV input clock divided by 10
10: Div11: PREDIV input clock divided by 11
11: Div12: PREDIV input clock divided by 12
12: Div13: PREDIV input clock divided by 13
13: Div14: PREDIV input clock divided by 14
14: Div15: PREDIV input clock divided by 15
15: Div16: PREDIV input clock divided by 16

ADC12PRES

Bits 4-8: ADC1 and ADC2 prescaler.

Allowed values:
0: NoClock: No clock
16: Div1: PLL clock not divided
17: Div2: PLL clock divided by 2
18: Div4: PLL clock divided by 4
19: Div6: PLL clock divided by 6
20: Div8: PLL clock divided by 8
21: Div10: PLL clock divided by 10
22: Div12: PLL clock divided by 12
23: Div16: PLL clock divided by 16
24: Div32: PLL clock divided by 32
25: Div64: PLL clock divided by 64
26: Div128: PLL clock divided by 128
27: Div256: PLL clock divided by 256

ADC34PRES

Bits 9-13: ADC3 and ADC4 prescaler.

Allowed values:
0: NoClock: No clock
16: Div1: PLL clock not divided
17: Div2: PLL clock divided by 2
18: Div4: PLL clock divided by 4
19: Div6: PLL clock divided by 6
20: Div8: PLL clock divided by 8
21: Div10: PLL clock divided by 10
22: Div12: PLL clock divided by 12
23: Div16: PLL clock divided by 16
24: Div32: PLL clock divided by 32
25: Div64: PLL clock divided by 64
26: Div128: PLL clock divided by 128
27: Div256: PLL clock divided by 256

CFGR3

Clock configuration register 3

Offset: 0x30, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
						TIM34SW rw	TIM2SW rw	UART5SW rw		UART4SW rw		USART3SW rw		USART2SW rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TIM20SW rw		TIM17SW rw		TIM16SW rw	TIM15SW rw	TIM8SW rw	TIM1SW rw		I2C3SW rw	I2C2SW rw	I2C1SW rw			USART1SW rw

Toggle fields

USART1SW

Bits 0-1: USART1 clock source selection.

Allowed values:
0: PCLK: PCLK selected as USART clock source
1: SYSCLK: SYSCLK selected as USART clock source
2: LSE: LSE selected as USART clock source
3: HSI: HSI selected as USART clock source

I2C1SW

Bit 4: I2C1 clock source selection.

Allowed values:
0: HSI: HSI clock selected as I2C clock source
1: SYSCLK: SYSCLK clock selected as I2C clock source

I2C2SW

Bit 5: I2C2 clock source selection.

Allowed values:
0: HSI: HSI clock selected as I2C clock source
1: SYSCLK: SYSCLK clock selected as I2C clock source

I2C3SW

Bit 6: I2C3 clock source selection.

Allowed values:
0: HSI: HSI clock selected as I2C clock source
1: SYSCLK: SYSCLK clock selected as I2C clock source

TIM1SW

Bit 8: Timer1 clock source selection.

Allowed values:
0: PCLK2: PCLK2 clock (doubled frequency when prescaled)
1: PLL: PLL vco output (running up to 144 MHz)

TIM8SW

Bit 9: Timer8 clock source selection.

Allowed values:
0: PCLK2: PCLK2 clock (doubled frequency when prescaled)
1: PLL: PLL vco output (running up to 144 MHz)

TIM15SW

Bit 10: Timer15 clock source selection.

Allowed values:
0: PCLK2: PCLK2 clock (doubled frequency when prescaled)
1: PLL: PLL vco output (running up to 144 MHz)

TIM16SW

Bit 11: Timer16 clock source selection.

Allowed values:
0: PCLK2: PCLK2 clock (doubled frequency when prescaled)
1: PLL: PLL vco output (running up to 144 MHz)

TIM17SW

Bit 13: Timer17 clock source selection.

Allowed values:
0: PCLK2: PCLK2 clock (doubled frequency when prescaled)
1: PLL: PLL vco output (running up to 144 MHz)

TIM20SW

Bit 15: Timer20 clock source selection.

Allowed values:
0: PCLK2: PCLK2 clock (doubled frequency when prescaled)
1: PLL: PLL vco output (running up to 144 MHz)

USART2SW

Bits 16-17: USART2 clock source selection.

Allowed values:
0: PCLK: PCLK selected as USART clock source
1: SYSCLK: SYSCLK selected as USART clock source
2: LSE: LSE selected as USART clock source
3: HSI: HSI selected as USART clock source

USART3SW

Bits 18-19: USART3 clock source selection.

Allowed values:
0: PCLK: PCLK selected as USART clock source
1: SYSCLK: SYSCLK selected as USART clock source
2: LSE: LSE selected as USART clock source
3: HSI: HSI selected as USART clock source

UART4SW

Bits 20-21: UART4 clock source selection.

Allowed values:
0: PCLK: PCLK selected as USART clock source
1: SYSCLK: SYSCLK selected as USART clock source
2: LSE: LSE selected as USART clock source
3: HSI: HSI selected as USART clock source

UART5SW

Bits 22-23: UART5 clock source selection.

Allowed values:
0: PCLK: PCLK selected as USART clock source
1: SYSCLK: SYSCLK selected as USART clock source
2: LSE: LSE selected as USART clock source
3: HSI: HSI selected as USART clock source

TIM2SW

Bit 24: Timer2 clock source selection.

Allowed values:
0: PCLK2: PCLK2 clock (doubled frequency when prescaled)
1: PLL: PLL vco output (running up to 144 MHz)

TIM34SW

Bit 25: Timer34 clock source selection.

Allowed values:
0: PCLK2: PCLK2 clock (doubled frequency when prescaled)
1: PLL: PLL vco output (running up to 144 MHz)

RTC

0x40002800: Real-time clock

159/159 fields covered.

Toggle register map

Offset	Name	31	30	29	27	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	TR						PM	HT		HU					MNT			MNU					ST			SU
0x4	DR					YT				YU				WDU			MT	MU						DT		DU
0x8	CR					COE	OSEL		POL	COSEL	BKP	SUB1H	ADD1H	TSIE	WUTIE	ALRBIE	ALRAIE	TSE	WUTE	ALRBE	ALRAE		FMT	BYPSHAD	REFCKON	TSEDGE	WUCKSEL
0xc	ISR												RECALPF	TAMP3F	TAMP2F	TAMP1F	TSOVF	TSF	WUTF	ALRBF	ALRAF	INIT	INITF	RSF	INITS	SHPF	WUTWF	ALRBWF	ALRAWF
0x10	PRER						PREDIV_A								PREDIV_S
0x14	WUTR													WUT
0x1c	ALRM[A]R	MSK4	WDSEL	DT	DU	MSK3	PM	HT		HU				MSK2	MNT			MNU				MSK1	ST			SU
0x20	ALRM[B]R	MSK4	WDSEL	DT	DU	MSK3	PM	HT		HU				MSK2	MNT			MNU				MSK1	ST			SU
0x24	WPR																					KEY
0x28	SSR													SS
0x2c	SHIFTR	ADD1S													SUBFS
0x30	TSTR						PM	HT		HU					MNT			MNU					ST			SU
0x34	TSDR					YT				YU				WDU			MT	MU						DT		DU
0x38	TSSSR													SS
0x3c	CALR													CALP	CALW8	CALW16					CALM
0x40	TAFCR					PC15MODE	PC15VALUE	PC14MODE	PC14VALUE	PC13MODE	PC13VALUE			TAMPPUDIS	TAMPPRCH		TAMPFLT		TAMPFREQ			TAMPTS	TAMP3TRG	TAMP3E	TAMP2TRG	TAMP2E	TAMPIE	TAMP1TRG	TAMP1E
0x44	ALRM[A]SSR				MASKSS										SS
0x48	ALRM[B]SSR				MASKSS										SS
0x50	BKP[0]R	BKP												BKP
0x54	BKP[1]R	BKP												BKP
0x58	BKP[2]R	BKP												BKP
0x5c	BKP[3]R	BKP												BKP
0x60	BKP[4]R	BKP												BKP
0x64	BKP[5]R	BKP												BKP
0x68	BKP[6]R	BKP												BKP
0x6c	BKP[7]R	BKP												BKP
0x70	BKP[8]R	BKP												BKP
0x74	BKP[9]R	BKP												BKP
0x78	BKP[10]R	BKP												BKP
0x7c	BKP[11]R	BKP												BKP
0x80	BKP[12]R	BKP												BKP
0x84	BKP[13]R	BKP												BKP
0x88	BKP[14]R	BKP												BKP
0x8c	BKP[15]R	BKP												BKP
0x90	BKP[16]R	BKP												BKP
0x94	BKP[17]R	BKP												BKP
0x98	BKP[18]R	BKP												BKP
0x9c	BKP[19]R	BKP												BKP
0xa0	BKP[20]R	BKP												BKP
0xa4	BKP[21]R	BKP												BKP
0xa8	BKP[22]R	BKP												BKP
0xac	BKP[23]R	BKP												BKP
0xb0	BKP[24]R	BKP												BKP
0xb4	BKP[25]R	BKP												BKP
0xb8	BKP[26]R	BKP												BKP
0xbc	BKP[27]R	BKP												BKP
0xc0	BKP[28]R	BKP												BKP
0xc4	BKP[29]R	BKP												BKP
0xc8	BKP[30]R	BKP												BKP
0xcc	BKP[31]R	BKP												BKP

Toggle registers

TR

time register

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

7/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
									PM rw	HT rw		HU rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	MNT rw			MNU rw					ST rw			SU rw

Toggle fields

SU

Bits 0-3: Second units in BCD format.

Allowed values: 0x0-0xf

ST

Bits 4-6: Second tens in BCD format.

Allowed values: 0x0-0x7

MNU

Bits 8-11: Minute units in BCD format.

Allowed values: 0x0-0xf

MNT

Bits 12-14: Minute tens in BCD format.

Allowed values: 0x0-0x7

HU

Bits 16-19: Hour units in BCD format.

Allowed values: 0x0-0xf

HT

Bits 20-21: Hour tens in BCD format.

Allowed values: 0x0-0x3

PM

Bit 22: AM/PM notation.

Allowed values:
0: AM: AM or 24-hour format
1: PM: PM

DR

date register

Offset: 0x4, size: 32, reset: 0x00002101, access: read-write

7/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								YT rw				YU rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
WDU rw			MT rw	MU rw						DT rw		DU rw

Toggle fields

DU

Bits 0-3: Date units in BCD format.

Allowed values: 0x0-0xf

DT

Bits 4-5: Date tens in BCD format.

Allowed values: 0x0-0x3

MU

Bits 8-11: Month units in BCD format.

Allowed values: 0x0-0xf

MT

Bit 12: Month tens in BCD format.

Allowed values:
0: Zero: Month tens is 0
1: One: Month tens is 1

WDU

Bits 13-15: Week day units.

Allowed values: 0x1-0x7

YU

Bits 16-19: Year units in BCD format.

Allowed values: 0x0-0xf

YT

Bits 20-23: Year tens in BCD format.

Allowed values: 0x0-0xf

CR

control register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

20/20 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								COE rw	OSEL rw		POL rw	COSEL rw	BKP rw	SUB1H rw	ADD1H rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TSIE rw	WUTIE rw	ALRBIE rw	ALRAIE rw	TSE rw	WUTE rw	ALRBE rw	ALRAE rw		FMT rw	BYPSHAD rw	REFCKON rw	TSEDGE rw	WUCKSEL rw

Toggle fields

WUCKSEL

Bits 0-2: Wakeup clock selection.

Allowed values:
0: Div16: RTC/16 clock is selected
1: Div8: RTC/8 clock is selected
2: Div4: RTC/4 clock is selected
3: Div2: RTC/2 clock is selected
4: ClockSpare: ck_spre (usually 1 Hz) clock is selected
6: ClockSpareWithOffset: ck_spre (usually 1 Hz) clock is selected and 2^16 is added to the WUT counter value

TSEDGE

Bit 3: Time-stamp event active edge.

Allowed values:
0: RisingEdge: RTC_TS input rising edge generates a time-stamp event
1: FallingEdge: RTC_TS input falling edge generates a time-stamp event

REFCKON

Bit 4: Reference clock detection enable (50 or 60 Hz).

Allowed values:
0: Disabled: RTC_REFIN detection disabled
1: Enabled: RTC_REFIN detection enabled

BYPSHAD

Bit 5: Bypass the shadow registers.

Allowed values:
0: ShadowReg: Calendar values (when reading from RTC_SSR, RTC_TR, and RTC_DR) are taken from the shadow registers, which are updated once every two RTCCLK cycles
1: BypassShadowReg: Calendar values (when reading from RTC_SSR, RTC_TR, and RTC_DR) are taken directly from the calendar counters

FMT

Bit 6: Hour format.

Allowed values:
0: Twenty_Four_Hour: 24 hour/day format
1: AM_PM: AM/PM hour format

ALRAE

Bit 8: Alarm A enable.

Allowed values:
0: Disabled: Alarm A disabled
1: Enabled: Alarm A enabled

ALRBE

Bit 9: Alarm B enable.

Allowed values:
0: Disabled: Alarm B disabled
1: Enabled: Alarm B enabled

WUTE

Bit 10: Wakeup timer enable.

Allowed values:
0: Disabled: Wakeup timer disabled
1: Enabled: Wakeup timer enabled

TSE

Bit 11: Time stamp enable.

Allowed values:
0: Disabled: Timestamp disabled
1: Enabled: Timestamp enabled

ALRAIE

Bit 12: Alarm A interrupt enable.

Allowed values:
0: Disabled: Alarm A interrupt disabled
1: Enabled: Alarm A interrupt enabled

ALRBIE

Bit 13: Alarm B interrupt enable.

Allowed values:
0: Disabled: Alarm B Interrupt disabled
1: Enabled: Alarm B Interrupt enabled

WUTIE

Bit 14: Wakeup timer interrupt enable.

Allowed values:
0: Disabled: Wakeup timer interrupt disabled
1: Enabled: Wakeup timer interrupt enabled

TSIE

Bit 15: Time-stamp interrupt enable.

Allowed values:
0: Disabled: Time-stamp Interrupt disabled
1: Enabled: Time-stamp Interrupt enabled

ADD1H

Bit 16: Add 1 hour (summer time change).

Allowed values:
1: Add1: Adds 1 hour to the current time. This can be used for summer time change outside initialization mode

SUB1H

Bit 17: Subtract 1 hour (winter time change).

Allowed values:
1: Sub1: Subtracts 1 hour to the current time. This can be used for winter time change outside initialization mode

BKP

Bit 18: Backup.

Allowed values:
0: DST_Not_Changed: Daylight Saving Time change has not been performed
1: DST_Changed: Daylight Saving Time change has been performed

COSEL

Bit 19: Calibration output selection.

Allowed values:
0: CalFreq_512Hz: Calibration output is 512 Hz (with default prescaler setting)
1: CalFreq_1Hz: Calibration output is 1 Hz (with default prescaler setting)

POL

Bit 20: Output polarity.

Allowed values:
0: High: The pin is high when ALRAF/ALRBF/WUTF is asserted (depending on OSEL[1:0])
1: Low: The pin is low when ALRAF/ALRBF/WUTF is asserted (depending on OSEL[1:0])

OSEL

Bits 21-22: Output selection.

Allowed values:
0: Disabled: Output disabled
1: AlarmA: Alarm A output enabled
2: AlarmB: Alarm B output enabled
3: Wakeup: Wakeup output enabled

COE

Bit 23: Calibration output enable.

Allowed values:
0: Disabled: Calibration output disabled
1: Enabled: Calibration output enabled

ISR

initialization and status register

Offset: 0xc, size: 32, reset: 0x00000007, access: Unspecified

17/17 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															RECALPF r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TAMP3F rw	TAMP2F rw	TAMP1F rw	TSOVF rw	TSF rw	WUTF rw	ALRBF rw	ALRAF rw	INIT rw	INITF r	RSF rw	INITS r	SHPF rw	WUTWF r	ALRBWF r	ALRAWF r

Toggle fields

ALRAWF

Bit 0: Alarm A write flag.

Allowed values:
0: UpdateNotAllowed: Alarm update not allowed
1: UpdateAllowed: Alarm update allowed

ALRBWF

Bit 1: Alarm B write flag.

Allowed values:
0: UpdateNotAllowed: Alarm update not allowed
1: UpdateAllowed: Alarm update allowed

WUTWF

Bit 2: Wakeup timer write flag.

Allowed values:
0: UpdateNotAllowed: Wakeup timer configuration update not allowed
1: UpdateAllowed: Wakeup timer configuration update allowed

SHPF

Bit 3: Shift operation pending.

Allowed values:
0: NoShiftPending: No shift operation is pending
1: ShiftPending: A shift operation is pending

INITS

Bit 4: Initialization status flag.

Allowed values:
0: NotInitalized: Calendar has not been initialized
1: Initalized: Calendar has been initialized

RSF

Bit 5: Registers synchronization flag.

Allowed values:
0: NotSynced: Calendar shadow registers not yet synchronized
1: Synced: Calendar shadow registers synchronized

INITF

Bit 6: Initialization flag.

Allowed values:
0: NotAllowed: Calendar registers update is not allowed
1: Allowed: Calendar registers update is allowed

INIT

Bit 7: Initialization mode.

Allowed values:
0: FreeRunningMode: Free running mode
1: InitMode: Initialization mode used to program time and date register (RTC_TR and RTC_DR), and prescaler register (RTC_PRER). Counters are stopped and start counting from the new value when INIT is reset.

ALRAF

Bit 8: Alarm A flag.

Allowed values:
1: Match: This flag is set by hardware when the time/date registers (RTC_TR and RTC_DR) match the Alarm A register (RTC_ALRMAR)

ALRBF

Bit 9: Alarm B flag.

Allowed values:
1: Match: This flag is set by hardware when the time/date registers (RTC_TR and RTC_DR) match the Alarm B register (RTC_ALRMBR)

WUTF

Bit 10: Wakeup timer flag.

Allowed values:
1: Zero: This flag is set by hardware when the wakeup auto-reload counter reaches 0

TSF

Bit 11: Time-stamp flag.

Allowed values:
1: TimestampEvent: This flag is set by hardware when a time-stamp event occurs

TSOVF

Bit 12: Time-stamp overflow flag.

Allowed values:
1: Overflow: This flag is set by hardware when a time-stamp event occurs while TSF is already set

TAMP1F

Bit 13: Tamper detection flag.

Allowed values:
1: Tampered: This flag is set by hardware when a tamper detection event is detected on the RTC_TAMPx input

TAMP2F

Bit 14: RTC_TAMP2 detection flag.

Allowed values:
1: Tampered: This flag is set by hardware when a tamper detection event is detected on the RTC_TAMPx input

TAMP3F

Bit 15: RTC_TAMP3 detection flag.

Allowed values:
1: Tampered: This flag is set by hardware when a tamper detection event is detected on the RTC_TAMPx input

RECALPF

Bit 16: Recalibration pending Flag.

Allowed values:
1: Pending: The RECALPF status flag is automatically set to 1 when software writes to the RTC_CALR register, indicating that the RTC_CALR register is blocked. When the new calibration settings are taken into account, this bit returns to 0

PRER

prescaler register

Offset: 0x10, size: 32, reset: 0x007F00FF, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
									PREDIV_A rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	PREDIV_S rw

Toggle fields

PREDIV_S

Bits 0-14: Synchronous prescaler factor.

Allowed values: 0x0-0x7fff

PREDIV_A

Bits 16-22: Asynchronous prescaler factor.

Allowed values: 0x0-0x7f

WUTR

wakeup timer register

Offset: 0x14, size: 32, reset: 0x0000FFFF, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
WUT rw

Toggle fields

WUT

Bits 0-15: Wakeup auto-reload value bits.

Allowed values: 0x0-0xffff

ALRM[A]R

Alarm A register

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

14/14 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MSK4 rw	WDSEL rw	DT rw		DU rw				MSK3 rw	PM rw	HT rw		HU rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MSK2 rw	MNT rw			MNU rw				MSK1 rw	ST rw			SU rw

Toggle fields

SU

Bits 0-3: Second units in BCD format.

Allowed values: 0x0-0xf

ST

Bits 4-6: Second tens in BCD format.

Allowed values: 0x0-0x7

MSK1

Bit 7: Alarm seconds mask.

Allowed values:
0: Mask: Alarm set if the date/day match
1: NotMask: Date/day don’t care in Alarm comparison

MNU

Bits 8-11: Minute units in BCD format.

Allowed values: 0x0-0xf

MNT

Bits 12-14: Minute tens in BCD format.

Allowed values: 0x0-0x7

MSK2

Bit 15: Alarm minutes mask.

Allowed values:
0: Mask: Alarm set if the date/day match
1: NotMask: Date/day don’t care in Alarm comparison

HU

Bits 16-19: Hour units in BCD format.

Allowed values: 0x0-0xf

HT

Bits 20-21: Hour tens in BCD format.

Allowed values: 0x0-0x3

PM

Bit 22: AM/PM notation.

Allowed values:
0: AM: AM or 24-hour format
1: PM: PM

MSK3

Bit 23: Alarm hours mask.

Allowed values:
0: Mask: Alarm set if the date/day match
1: NotMask: Date/day don’t care in Alarm comparison

DU

Bits 24-27: Date units or day in BCD format.

Allowed values: 0x0-0xf

DT

Bits 28-29: Date tens in BCD format.

Allowed values: 0x0-0x3

WDSEL

Bit 30: Week day selection.

Allowed values:
0: DateUnits: DU[3:0] represents the date units
1: WeekDay: DU[3:0] represents the week day. DT[1:0] is don’t care.

MSK4

Bit 31: Alarm date mask.

Allowed values:
0: Mask: Alarm set if the date/day match
1: NotMask: Date/day don’t care in Alarm comparison

ALRM[B]R

Alarm B register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

14/14 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MSK4 rw	WDSEL rw	DT rw		DU rw				MSK3 rw	PM rw	HT rw		HU rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MSK2 rw	MNT rw			MNU rw				MSK1 rw	ST rw			SU rw

Toggle fields

SU

Bits 0-3: Second units in BCD format.

Allowed values: 0x0-0xf

ST

Bits 4-6: Second tens in BCD format.

Allowed values: 0x0-0x7

MSK1

Bit 7: Alarm seconds mask.

Allowed values:
0: Mask: Alarm set if the date/day match
1: NotMask: Date/day don’t care in Alarm comparison

MNU

Bits 8-11: Minute units in BCD format.

Allowed values: 0x0-0xf

MNT

Bits 12-14: Minute tens in BCD format.

Allowed values: 0x0-0x7

MSK2

Bit 15: Alarm minutes mask.

Allowed values:
0: Mask: Alarm set if the date/day match
1: NotMask: Date/day don’t care in Alarm comparison

HU

Bits 16-19: Hour units in BCD format.

Allowed values: 0x0-0xf

HT

Bits 20-21: Hour tens in BCD format.

Allowed values: 0x0-0x3

PM

Bit 22: AM/PM notation.

Allowed values:
0: AM: AM or 24-hour format
1: PM: PM

MSK3

Bit 23: Alarm hours mask.

Allowed values:
0: Mask: Alarm set if the date/day match
1: NotMask: Date/day don’t care in Alarm comparison

DU

Bits 24-27: Date units or day in BCD format.

Allowed values: 0x0-0xf

DT

Bits 28-29: Date tens in BCD format.

Allowed values: 0x0-0x3

WDSEL

Bit 30: Week day selection.

Allowed values:
0: DateUnits: DU[3:0] represents the date units
1: WeekDay: DU[3:0] represents the week day. DT[1:0] is don’t care.

MSK4

Bit 31: Alarm date mask.

Allowed values:
0: Mask: Alarm set if the date/day match
1: NotMask: Date/day don’t care in Alarm comparison

WPR

write protection register

Offset: 0x24, size: 32, reset: 0x00000000, access: write-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								KEY w

Toggle fields

KEY

Bits 0-7: Write protection key.

Allowed values: 0x0-0xff

SSR

sub second register

Offset: 0x28, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SS r

Toggle fields

SS

Bits 0-15: Sub second value.

Allowed values: 0x0-0xffff

SHIFTR

shift control register

Offset: 0x2c, size: 32, reset: 0x00000000, access: write-only

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ADD1S w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	SUBFS w

Toggle fields

SUBFS

Bits 0-14: Subtract a fraction of a second.

Allowed values: 0x0-0x7fff

ADD1S

Bit 31: Add one second.

Allowed values:
1: Add1: Add one second to the clock/calendar

TSTR

time stamp time register

Offset: 0x30, size: 32, reset: 0x00000000, access: read-write

7/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
									PM rw	HT rw		HU rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	MNT rw			MNU rw					ST rw			SU rw

Toggle fields

SU

Bits 0-3: Second units in BCD format.

Allowed values: 0x0-0xf

ST

Bits 4-6: Second tens in BCD format.

Allowed values: 0x0-0x7

MNU

Bits 8-11: Minute units in BCD format.

Allowed values: 0x0-0xf

MNT

Bits 12-14: Minute tens in BCD format.

Allowed values: 0x0-0x7

HU

Bits 16-19: Hour units in BCD format.

Allowed values: 0x0-0xf

HT

Bits 20-21: Hour tens in BCD format.

Allowed values: 0x0-0x3

PM

Bit 22: AM/PM notation.

Allowed values:
0: AM: AM or 24-hour format
1: PM: PM

TSDR

time stamp date register

Offset: 0x34, size: 32, reset: 0x00002101, access: read-write

7/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								YT rw				YU rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
WDU rw			MT rw	MU rw						DT rw		DU rw

Toggle fields

DU

Bits 0-3: Date units in BCD format.

Allowed values: 0x0-0xf

DT

Bits 4-5: Date tens in BCD format.

Allowed values: 0x0-0x3

MU

Bits 8-11: Month units in BCD format.

Allowed values: 0x0-0xf

MT

Bit 12: Month tens in BCD format.

Allowed values:
0: Zero: Month tens is 0
1: One: Month tens is 1

WDU

Bits 13-15: Week day units.

Allowed values: 0x1-0x7

YU

Bits 16-19: Year units in BCD format.

Allowed values: 0x0-0xf

YT

Bits 20-23: Year tens in BCD format.

Allowed values: 0x0-0xf

TSSSR

timestamp sub second register

Offset: 0x38, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SS r

Toggle fields

SS

Bits 0-15: Sub second value.

Allowed values: 0x0-0xffff

CALR

calibration register

Offset: 0x3c, size: 32, reset: 0x00000000, access: read-write

4/4 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CALP rw	CALW8 rw	CALW16 rw					CALM rw

Toggle fields

CALM

Bits 0-8: Calibration minus.

Allowed values: 0x0-0x1ff

CALW16

Bit 13: Use a 16-second calibration cycle period.

Allowed values:
1: Sixteen_Second: When CALW16 is set to ‘1’, the 16-second calibration cycle period is selected.This bit must not be set to ‘1’ if CALW8=1

CALW8

Bit 14: Use an 8-second calibration cycle period.

Allowed values:
1: Eight_Second: When CALW8 is set to ‘1’, the 8-second calibration cycle period is selected

CALP

Bit 15: Increase frequency of RTC by 488.5 ppm.

Allowed values:
0: NoChange: No RTCCLK pulses are added
1: IncreaseFreq: One RTCCLK pulse is effectively inserted every 2^11 pulses (frequency increased by 488.5 ppm)

TAFCR

tamper and alternate function configuration register

Offset: 0x40, size: 32, reset: 0x00000000, access: read-write

18/18 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								PC15MODE rw	PC15VALUE rw	PC14MODE rw	PC14VALUE rw	PC13MODE rw	PC13VALUE rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TAMPPUDIS rw	TAMPPRCH rw		TAMPFLT rw		TAMPFREQ rw			TAMPTS rw	TAMP3TRG rw	TAMP3E rw	TAMP2TRG rw	TAMP2E rw	TAMPIE rw	TAMP1TRG rw	TAMP1E rw

Toggle fields

TAMP1E

Bit 0: Tamper 1 detection enable.

Allowed values:
0: Disabled: RTC_TAMPx input detection disabled
1: Enabled: RTC_TAMPx input detection enabled

TAMP1TRG

Bit 1: Active level for tamper 1.

Allowed values:
0: RisingEdge: If TAMPFLT = 00: RTC_TAMPx input rising edge triggers a tamper detection event. If TAMPFLT ≠ 00: RTC_TAMPx input staying low triggers a tamper detection event.
1: FallingEdge: If TAMPFLT = 00: RTC_TAMPx input staying high triggers a tamper detection event. If TAMPFLT ≠ 00: RTC_TAMPx input falling edge triggers a tamper detection event

TAMPIE

Bit 2: Tamper interrupt enable.

Allowed values:
0: Disabled: Tamper interrupt disabled
1: Enabled: Tamper interrupt enabled

TAMP2E

Bit 3: Tamper 2 detection enable.

Allowed values:
0: Disabled: RTC_TAMPx input detection disabled
1: Enabled: RTC_TAMPx input detection enabled

TAMP2TRG

Bit 4: Active level for tamper 2.

Allowed values:
0: RisingEdge: If TAMPFLT = 00: RTC_TAMPx input rising edge triggers a tamper detection event. If TAMPFLT ≠ 00: RTC_TAMPx input staying low triggers a tamper detection event.
1: FallingEdge: If TAMPFLT = 00: RTC_TAMPx input staying high triggers a tamper detection event. If TAMPFLT ≠ 00: RTC_TAMPx input falling edge triggers a tamper detection event

TAMP3E

Bit 5: Tamper 3 detection enable.

Allowed values:
0: Disabled: RTC_TAMPx input detection disabled
1: Enabled: RTC_TAMPx input detection enabled

TAMP3TRG

Bit 6: Active level for tamper 3.

Allowed values:
0: RisingEdge: If TAMPFLT = 00: RTC_TAMPx input rising edge triggers a tamper detection event. If TAMPFLT ≠ 00: RTC_TAMPx input staying low triggers a tamper detection event.
1: FallingEdge: If TAMPFLT = 00: RTC_TAMPx input staying high triggers a tamper detection event. If TAMPFLT ≠ 00: RTC_TAMPx input falling edge triggers a tamper detection event

TAMPTS

Bit 7: Activate timestamp on tamper detection event.

Allowed values:
0: NoSave: Tamper detection event does not cause a timestamp to be saved
1: Save: Save timestamp on tamper detection event

TAMPFREQ

Bits 8-10: Tamper sampling frequency.

Allowed values:
0: Div32768: RTCCLK / 32768 (1 Hz when RTCCLK = 32768 Hz)
1: Div16384: RTCCLK / 16384 (2 Hz when RTCCLK = 32768 Hz)
2: Div8192: RTCCLK / 8192 (4 Hz when RTCCLK = 32768 Hz)
3: Div4096: RTCCLK / 4096 (8 Hz when RTCCLK = 32768 Hz)
4: Div2048: RTCCLK / 2048 (16 Hz when RTCCLK = 32768 Hz)
5: Div1024: RTCCLK / 1024 (32 Hz when RTCCLK = 32768 Hz)
6: Div512: RTCCLK / 512 (64 Hz when RTCCLK = 32768 Hz)
7: Div256: RTCCLK / 256 (128 Hz when RTCCLK = 32768 Hz)

TAMPFLT

Bits 11-12: Tamper filter count.

Allowed values:
0: Immediate: Tamper event is activated on edge of RTC_TAMPx input transitions to the active level (no internal pull-up on RTC_TAMPx input)
1: Samples2: Tamper event is activated after 2 consecutive samples at the active level
2: Samples4: Tamper event is activated after 4 consecutive samples at the active level
3: Samples8: Tamper event is activated after 8 consecutive samples at the active level

TAMPPRCH

Bits 13-14: Tamper precharge duration.

Allowed values:
0: Cycles1: 1 RTCCLK cycle
1: Cycles2: 2 RTCCLK cycles
2: Cycles4: 4 RTCCLK cycles
3: Cycles8: 8 RTCCLK cycles

TAMPPUDIS

Bit 15: TAMPER pull-up disable.

Allowed values:
0: Enabled: Precharge RTC_TAMPx pins before sampling (enable internal pull-up)
1: Disabled: Disable precharge of RTC_TAMPx pins

PC13VALUE

Bit 18: PC13 value.

Allowed values:
0: Low: If the LSE is disabled and PCxMODE = 1, set PCxVALUE to logic low
1: High: If the LSE is disabled and PCxMODE = 1, set PCxVALUE to logic high

PC13MODE

Bit 19: PC13 mode.

Allowed values:
0: Floating: PCx is controlled by the GPIO configuration Register. Consequently PC15 is floating in Standby mode
1: PushPull: PCx is forced to push-pull output if LSE is disabled

PC14VALUE

Bit 20: PC14 value.

Allowed values:
0: Low: If the LSE is disabled and PCxMODE = 1, set PCxVALUE to logic low
1: High: If the LSE is disabled and PCxMODE = 1, set PCxVALUE to logic high

PC14MODE

Bit 21: PC 14 mode.

Allowed values:
0: Floating: PCx is controlled by the GPIO configuration Register. Consequently PC15 is floating in Standby mode
1: PushPull: PCx is forced to push-pull output if LSE is disabled

PC15VALUE

Bit 22: PC15 value.

Allowed values:
0: Low: If the LSE is disabled and PCxMODE = 1, set PCxVALUE to logic low
1: High: If the LSE is disabled and PCxMODE = 1, set PCxVALUE to logic high

PC15MODE

Bit 23: PC15 mode.

Allowed values:
0: Floating: PCx is controlled by the GPIO configuration Register. Consequently PC15 is floating in Standby mode
1: PushPull: PCx is forced to push-pull output if LSE is disabled

ALRM[A]SSR

Alarm A sub-second register

Offset: 0x44, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				MASKSS rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	SS rw

Toggle fields

SS

Bits 0-14: Sub seconds value.

Allowed values: 0x0-0x7fff

MASKSS

Bits 24-27: Mask the most-significant bits starting at this bit.

Allowed values: 0x0-0xf

ALRM[B]SSR

Alarm B sub-second register

Offset: 0x48, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				MASKSS rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	SS rw

Toggle fields

SS

Bits 0-14: Sub seconds value.

Allowed values: 0x0-0x7fff

MASKSS

Bits 24-27: Mask the most-significant bits starting at this bit.

Allowed values: 0x0-0xf

BKP[0]R

backup register

Offset: 0x50, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BKP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BKP rw

Toggle fields

BKP

Bits 0-31: BKP.

Allowed values: 0x0-0xffffffff

BKP[1]R

backup register

Offset: 0x54, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BKP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BKP rw

Toggle fields

BKP

Bits 0-31: BKP.

Allowed values: 0x0-0xffffffff

BKP[2]R

backup register

Offset: 0x58, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BKP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BKP rw

Toggle fields

BKP

Bits 0-31: BKP.

Allowed values: 0x0-0xffffffff

BKP[3]R

backup register

Offset: 0x5c, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BKP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BKP rw

Toggle fields

BKP

Bits 0-31: BKP.

Allowed values: 0x0-0xffffffff

BKP[4]R

backup register

Offset: 0x60, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BKP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BKP rw

Toggle fields

BKP

Bits 0-31: BKP.

Allowed values: 0x0-0xffffffff

BKP[5]R

backup register

Offset: 0x64, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BKP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BKP rw

Toggle fields

BKP

Bits 0-31: BKP.

Allowed values: 0x0-0xffffffff

BKP[6]R

backup register

Offset: 0x68, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BKP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BKP rw

Toggle fields

BKP

Bits 0-31: BKP.

Allowed values: 0x0-0xffffffff

BKP[7]R

backup register

Offset: 0x6c, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BKP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BKP rw

Toggle fields

BKP

Bits 0-31: BKP.

Allowed values: 0x0-0xffffffff

BKP[8]R

backup register

Offset: 0x70, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BKP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BKP rw

Toggle fields

BKP

Bits 0-31: BKP.

Allowed values: 0x0-0xffffffff

BKP[9]R

backup register

Offset: 0x74, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BKP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BKP rw

Toggle fields

BKP

Bits 0-31: BKP.

Allowed values: 0x0-0xffffffff

BKP[10]R

backup register

Offset: 0x78, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BKP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BKP rw

Toggle fields

BKP

Bits 0-31: BKP.

Allowed values: 0x0-0xffffffff

BKP[11]R

backup register

Offset: 0x7c, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BKP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BKP rw

Toggle fields

BKP

Bits 0-31: BKP.

Allowed values: 0x0-0xffffffff

BKP[12]R

backup register

Offset: 0x80, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BKP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BKP rw

Toggle fields

BKP

Bits 0-31: BKP.

Allowed values: 0x0-0xffffffff

BKP[13]R

backup register

Offset: 0x84, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BKP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BKP rw

Toggle fields

BKP

Bits 0-31: BKP.

Allowed values: 0x0-0xffffffff

BKP[14]R

backup register

Offset: 0x88, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BKP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BKP rw

Toggle fields

BKP

Bits 0-31: BKP.

Allowed values: 0x0-0xffffffff

BKP[15]R

backup register

Offset: 0x8c, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BKP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BKP rw

Toggle fields

BKP

Bits 0-31: BKP.

Allowed values: 0x0-0xffffffff

BKP[16]R

backup register

Offset: 0x90, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BKP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BKP rw

Toggle fields

BKP

Bits 0-31: BKP.

Allowed values: 0x0-0xffffffff

BKP[17]R

backup register

Offset: 0x94, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BKP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BKP rw

Toggle fields

BKP

Bits 0-31: BKP.

Allowed values: 0x0-0xffffffff

BKP[18]R

backup register

Offset: 0x98, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BKP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BKP rw

Toggle fields

BKP

Bits 0-31: BKP.

Allowed values: 0x0-0xffffffff

BKP[19]R

backup register

Offset: 0x9c, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BKP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BKP rw

Toggle fields

BKP

Bits 0-31: BKP.

Allowed values: 0x0-0xffffffff

BKP[20]R

backup register

Offset: 0xa0, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BKP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BKP rw

Toggle fields

BKP

Bits 0-31: BKP.

Allowed values: 0x0-0xffffffff

BKP[21]R

backup register

Offset: 0xa4, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BKP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BKP rw

Toggle fields

BKP

Bits 0-31: BKP.

Allowed values: 0x0-0xffffffff

BKP[22]R

backup register

Offset: 0xa8, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BKP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BKP rw

Toggle fields

BKP

Bits 0-31: BKP.

Allowed values: 0x0-0xffffffff

BKP[23]R

backup register

Offset: 0xac, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BKP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BKP rw

Toggle fields

BKP

Bits 0-31: BKP.

Allowed values: 0x0-0xffffffff

BKP[24]R

backup register

Offset: 0xb0, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BKP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BKP rw

Toggle fields

BKP

Bits 0-31: BKP.

Allowed values: 0x0-0xffffffff

BKP[25]R

backup register

Offset: 0xb4, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BKP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BKP rw

Toggle fields

BKP

Bits 0-31: BKP.

Allowed values: 0x0-0xffffffff

BKP[26]R

backup register

Offset: 0xb8, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BKP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BKP rw

Toggle fields

BKP

Bits 0-31: BKP.

Allowed values: 0x0-0xffffffff

BKP[27]R

backup register

Offset: 0xbc, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BKP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BKP rw

Toggle fields

BKP

Bits 0-31: BKP.

Allowed values: 0x0-0xffffffff

BKP[28]R

backup register

Offset: 0xc0, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BKP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BKP rw

Toggle fields

BKP

Bits 0-31: BKP.

Allowed values: 0x0-0xffffffff

BKP[29]R

backup register

Offset: 0xc4, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BKP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BKP rw

Toggle fields

BKP

Bits 0-31: BKP.

Allowed values: 0x0-0xffffffff

BKP[30]R

backup register

Offset: 0xc8, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BKP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BKP rw

Toggle fields

BKP

Bits 0-31: BKP.

Allowed values: 0x0-0xffffffff

BKP[31]R

backup register

Offset: 0xcc, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BKP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BKP rw

Toggle fields

BKP

Bits 0-31: BKP.

Allowed values: 0x0-0xffffffff

SCB

0xe000ed00: System control block

5/74 fields covered.

Toggle register map

Offset	Name	31	30	29	28	27	26	25	24	23	22	19	18	17	16	15	14	13	12	11	10	9	8	7	5	4	3	2	1	0
0x0	CPUID	Implementer								Variant		Constant				PartNo											Revision
0x4	ICSR	NMIPENDSET			PENDSVSET	PENDSVCLR	PENDSTSET	PENDSTCLR			ISRPENDING		VECTPENDING			VECTPENDING				RETTOBASE			VECTACTIVE
0x8	VTOR			TBLOFF												TBLOFF
0xc	AIRCR	VECTKEYSTAT														ENDIANESS					PRIGROUP							SYSRESETREQ	VECTCLRACTIVE	VECTRESET
0x10	SCR																									SEVEONPEND		SLEEPDEEP	SLEEPONEXIT
0x14	CCR																					STKALIGN	BFHFNMIGN			DIV_0_TRP	UNALIGN__TRP		USERSETMPEND	NONBASETHRDENA
0x18	SHPR1									PRI_6						PRI_5								PRI_4
0x1c	SHPR2	PRI_11
0x20	SHPR3	PRI_15								PRI_14
0x24	SHCRS												USGFAULTENA	BUSFAULTENA	MEMFAULTENA	SVCALLPENDED	BUSFAULTPENDED	MEMFAULTPENDED	USGFAULTPENDED	SYSTICKACT	PENDSVACT		MONITORACT	SVCALLACT			USGFAULTACT		BUSFAULTACT	MEMFAULTACT
0x28	CFSR_UFSR_BFSR_MMFSR							DIVBYZERO	UNALIGNED			NOCP	INVPC	INVSTATE	UNDEFINSTR	BFARVALID		LSPERR	STKERR	UNSTKERR	IMPRECISERR	PRECISERR	IBUSERR	MMARVALID	MLSPERR	MSTKERR	MUNSTKERR		IACCVIOL
0x2c	HFSR	DEBUG_VT	FORCED																										VECTTBL
0x34	MMFAR	MMFAR														MMFAR
0x38	BFAR	BFAR														BFAR
0x3c	AFSR	IMPDEF														IMPDEF

Toggle registers

CPUID

CPUID base register

Offset: 0x0, size: 32, reset: 0x410FC241, access: read-only

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
Implementer r								Variant r				Constant r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PartNo r												Revision r

Toggle fields

Revision

Bits 0-3: Revision number.

PartNo

Bits 4-15: Part number of the processor.

Constant

Bits 16-19: Reads as 0xF.

Variant

Bits 20-23: Variant number.

Implementer

Bits 24-31: Implementer code.

ICSR

Interrupt control and state register

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

0/9 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
NMIPENDSET rw			PENDSVSET rw	PENDSVCLR rw	PENDSTSET rw	PENDSTCLR rw			ISRPENDING rw				VECTPENDING rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
VECTPENDING rw				RETTOBASE rw			VECTACTIVE rw

Toggle fields

VECTACTIVE

Bits 0-8: Active vector.

RETTOBASE

Bit 11: Return to base level.

VECTPENDING

Bits 12-18: Pending vector.

ISRPENDING

Bit 22: Interrupt pending flag.

PENDSTCLR

Bit 25: SysTick exception clear-pending bit.

PENDSTSET

Bit 26: SysTick exception set-pending bit.

PENDSVCLR

Bit 27: PendSV clear-pending bit.

PENDSVSET

Bit 28: PendSV set-pending bit.

NMIPENDSET

Bit 31: NMI set-pending bit..

VTOR

Vector table offset register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
		TBLOFF rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TBLOFF rw

Toggle fields

TBLOFF

Bits 9-29: Vector table base offset field.

AIRCR

Application interrupt and reset control register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

0/6 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
VECTKEYSTAT rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ENDIANESS rw					PRIGROUP rw								SYSRESETREQ rw	VECTCLRACTIVE rw	VECTRESET rw

Toggle fields

VECTRESET

Bit 0: VECTRESET.

VECTCLRACTIVE

Bit 1: VECTCLRACTIVE.

SYSRESETREQ

Bit 2: SYSRESETREQ.

PRIGROUP

Bits 8-10: PRIGROUP.

ENDIANESS

Bit 15: ENDIANESS.

VECTKEYSTAT

Bits 16-31: Register key.

SCR

System control register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

0/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
											SEVEONPEND rw		SLEEPDEEP rw	SLEEPONEXIT rw

Toggle fields

SLEEPONEXIT

Bit 1: SLEEPONEXIT.

SLEEPDEEP

Bit 2: SLEEPDEEP.

SEVEONPEND

Bit 4: Send Event on Pending bit.

CCR

Configuration and control register

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

0/6 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						STKALIGN rw	BFHFNMIGN rw				DIV_0_TRP rw	UNALIGN__TRP rw		USERSETMPEND rw	NONBASETHRDENA rw

Toggle fields

NONBASETHRDENA

Bit 0: Configures how the processor enters Thread mode.

USERSETMPEND

Bit 1: USERSETMPEND.

UNALIGN__TRP

Bit 3: UNALIGN_ TRP.

DIV_0_TRP

Bit 4: DIV_0_TRP.

BFHFNMIGN

Bit 8: BFHFNMIGN.

STKALIGN

Bit 9: STKALIGN.

SHPR1

System handler priority registers

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

0/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								PRI_6 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PRI_5 rw								PRI_4 rw

Toggle fields

PRI_4

Bits 0-7: Priority of system handler 4.

PRI_5

Bits 8-15: Priority of system handler 5.

PRI_6

Bits 16-23: Priority of system handler 6.

SHPR2

System handler priority registers

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PRI_11 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0

Toggle fields

PRI_11

Bits 24-31: Priority of system handler 11.

SHPR3

System handler priority registers

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

0/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PRI_15 rw								PRI_14 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0

Toggle fields

PRI_14

Bits 16-23: Priority of system handler 14.

PRI_15

Bits 24-31: Priority of system handler 15.

SHCRS

System handler control and state register

Offset: 0x24, size: 32, reset: 0x00000000, access: read-write

0/14 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
													USGFAULTENA rw	BUSFAULTENA rw	MEMFAULTENA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SVCALLPENDED rw	BUSFAULTPENDED rw	MEMFAULTPENDED rw	USGFAULTPENDED rw	SYSTICKACT rw	PENDSVACT rw		MONITORACT rw	SVCALLACT rw				USGFAULTACT rw		BUSFAULTACT rw	MEMFAULTACT rw

Toggle fields

MEMFAULTACT

Bit 0: Memory management fault exception active bit.

BUSFAULTACT

Bit 1: Bus fault exception active bit.

USGFAULTACT

Bit 3: Usage fault exception active bit.

SVCALLACT

Bit 7: SVC call active bit.

MONITORACT

Bit 8: Debug monitor active bit.

PENDSVACT

Bit 10: PendSV exception active bit.

SYSTICKACT

Bit 11: SysTick exception active bit.

USGFAULTPENDED

Bit 12: Usage fault exception pending bit.

MEMFAULTPENDED

Bit 13: Memory management fault exception pending bit.

BUSFAULTPENDED

Bit 14: Bus fault exception pending bit.

SVCALLPENDED

Bit 15: SVC call pending bit.

MEMFAULTENA

Bit 16: Memory management fault enable bit.

BUSFAULTENA

Bit 17: Bus fault enable bit.

USGFAULTENA

Bit 18: Usage fault enable bit.

CFSR_UFSR_BFSR_MMFSR

Configurable fault status register

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

0/18 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
						DIVBYZERO rw	UNALIGNED rw					NOCP rw	INVPC rw	INVSTATE rw	UNDEFINSTR rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BFARVALID rw		LSPERR rw	STKERR rw	UNSTKERR rw	IMPRECISERR rw	PRECISERR rw	IBUSERR rw	MMARVALID rw		MLSPERR rw	MSTKERR rw	MUNSTKERR rw		IACCVIOL rw

Toggle fields

IACCVIOL

Bit 1: Instruction access violation flag.

MUNSTKERR

Bit 3: Memory manager fault on unstacking for a return from exception.

MSTKERR

Bit 4: Memory manager fault on stacking for exception entry..

MLSPERR

Bit 5: MLSPERR.

MMARVALID

Bit 7: Memory Management Fault Address Register (MMAR) valid flag.

IBUSERR

Bit 8: Instruction bus error.

PRECISERR

Bit 9: Precise data bus error.

IMPRECISERR

Bit 10: Imprecise data bus error.

UNSTKERR

Bit 11: Bus fault on unstacking for a return from exception.

STKERR

Bit 12: Bus fault on stacking for exception entry.

LSPERR

Bit 13: Bus fault on floating-point lazy state preservation.

BFARVALID

Bit 15: Bus Fault Address Register (BFAR) valid flag.

UNDEFINSTR

Bit 16: Undefined instruction usage fault.

INVSTATE

Bit 17: Invalid state usage fault.

INVPC

Bit 18: Invalid PC load usage fault.

NOCP

Bit 19: No coprocessor usage fault..

UNALIGNED

Bit 24: Unaligned access usage fault.

DIVBYZERO

Bit 25: Divide by zero usage fault.

HFSR

Hard fault status register

Offset: 0x2c, size: 32, reset: 0x00000000, access: read-write

0/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
DEBUG_VT rw	FORCED rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														VECTTBL rw

Toggle fields

VECTTBL

Bit 1: Vector table hard fault.

FORCED

Bit 30: Forced hard fault.

DEBUG_VT

Bit 31: Reserved for Debug use.

MMFAR

Memory management fault address register

Offset: 0x34, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MMFAR rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MMFAR rw

Toggle fields

MMFAR

Bits 0-31: Memory management fault address.

BFAR

Bus fault address register

Offset: 0x38, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BFAR rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BFAR rw

Toggle fields

BFAR

Bits 0-31: Bus fault address.

AFSR

Auxiliary fault status register

Offset: 0x3c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
IMPDEF rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IMPDEF rw

Toggle fields

IMPDEF

Bits 0-31: Implementation defined.

SCB_ACTRL

0xe000e008: System control block ACTLR

0/5 fields covered.

Toggle register map

Offset	Name	31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	ACTRL																							DISOOFP	DISFPCA						DISFOLD	DISDEFWBUF	DISMCYCINT

Toggle registers

ACTRL

Auxiliary control register

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

0/5 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						DISOOFP rw	DISFPCA rw						DISFOLD rw	DISDEFWBUF rw	DISMCYCINT rw

Toggle fields

DISMCYCINT

Bit 0: DISMCYCINT.

DISDEFWBUF

Bit 1: DISDEFWBUF.

DISFOLD

Bit 2: DISFOLD.

DISFPCA

Bit 8: DISFPCA.

DISOOFP

Bit 9: DISOOFP.

SPI1

0x40013000: Serial peripheral interface/Inter-IC sound

53/53 fields covered.

Toggle register map

Offset	Name	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0 (16-bit)	CR1	BIDIMODE	BIDIOE	CRCEN	CRCNEXT	CRCL	RXONLY	SSM	SSI	LSBFIRST	SPE	BR			MSTR	CPOL	CPHA
0x4 (16-bit)	CR2		LDMA_TX	LDMA_RX	FRXTH	DS				TXEIE	RXNEIE	ERRIE	FRF	NSSP	SSOE	TXDMAEN	RXDMAEN
0x8 (16-bit)	SR				FTLVL		FRLVL		FRE	BSY	OVR	MODF	CRCERR	UDR	CHSIDE	TXE	RXNE
0xc (16-bit)	DR	DR
0xc (8-bit)	DR8									DR
0x10 (16-bit)	CRCPR	CRCPOLY
0x14 (16-bit)	RXCRCR	RxCRC
0x18 (16-bit)	TXCRCR	TxCRC
0x1c (16-bit)	I2SCFGR					I2SMOD	I2SE	I2SCFG		PCMSYNC		I2SSTD		CKPOL	DATLEN		CHLEN
0x20 (16-bit)	I2SPR							MCKOE	ODD	I2SDIV

Toggle registers

CR1

control register 1

Offset: 0x0, size: 16, reset: 0x00000000, access: read-write

14/14 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BIDIMODE rw	BIDIOE rw	CRCEN rw	CRCNEXT rw	CRCL rw	RXONLY rw	SSM rw	SSI rw	LSBFIRST rw	SPE rw	BR rw			MSTR rw	CPOL rw	CPHA rw

Toggle fields

CPHA

Bit 0: Clock phase.

Allowed values:
0: FirstEdge: The first clock transition is the first data capture edge
1: SecondEdge: The second clock transition is the first data capture edge

CPOL

Bit 1: Clock polarity.

Allowed values:
0: IdleLow: CK to 0 when idle
1: IdleHigh: CK to 1 when idle

MSTR

Bit 2: Master selection.

Allowed values:
0: Slave: Slave configuration
1: Master: Master configuration

BR

Bits 3-5: Baud rate control.

Allowed values:
0: Div2: f_PCLK / 2
1: Div4: f_PCLK / 4
2: Div8: f_PCLK / 8
3: Div16: f_PCLK / 16
4: Div32: f_PCLK / 32
5: Div64: f_PCLK / 64
6: Div128: f_PCLK / 128
7: Div256: f_PCLK / 256

SPE

Bit 6: SPI enable.

Allowed values:
0: Disabled: Peripheral disabled
1: Enabled: Peripheral enabled

LSBFIRST

Bit 7: Frame format.

Allowed values:
0: MSBFirst: Data is transmitted/received with the MSB first
1: LSBFirst: Data is transmitted/received with the LSB first

SSI

Bit 8: Internal slave select.

Allowed values:
0: SlaveSelected: 0 is forced onto the NSS pin and the I/O value of the NSS pin is ignored
1: SlaveNotSelected: 1 is forced onto the NSS pin and the I/O value of the NSS pin is ignored

SSM

Bit 9: Software slave management.

Allowed values:
0: Disabled: Software slave management disabled
1: Enabled: Software slave management enabled

RXONLY

Bit 10: Receive only.

Allowed values:
0: FullDuplex: Full duplex (Transmit and receive)
1: OutputDisabled: Output disabled (Receive-only mode)

CRCL

Bit 11: CRC length.

Allowed values:
0: EightBit: 8-bit CRC length
1: SixteenBit: 16-bit CRC length

CRCNEXT

Bit 12: CRC transfer next.

Allowed values:
0: TxBuffer: Next transmit value is from Tx buffer
1: CRC: Next transmit value is from Tx CRC register

CRCEN

Bit 13: Hardware CRC calculation enable.

Allowed values:
0: Disabled: CRC calculation disabled
1: Enabled: CRC calculation enabled

BIDIOE

Bit 14: Output enable in bidirectional mode.

Allowed values:
0: OutputDisabled: Output disabled (receive-only mode)
1: OutputEnabled: Output enabled (transmit-only mode)

BIDIMODE

Bit 15: Bidirectional data mode enable.

Allowed values:
0: Unidirectional: 2-line unidirectional data mode selected
1: Bidirectional: 1-line bidirectional data mode selected

CR2

control register 2

Offset: 0x4, size: 16, reset: 0x00000000, access: read-write

12/12 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	LDMA_TX rw	LDMA_RX rw	FRXTH rw	DS rw				TXEIE rw	RXNEIE rw	ERRIE rw	FRF rw	NSSP rw	SSOE rw	TXDMAEN rw	RXDMAEN rw

Toggle fields

RXDMAEN

Bit 0: Rx buffer DMA enable.

Allowed values:
0: Disabled: Rx buffer DMA disabled
1: Enabled: Rx buffer DMA enabled

TXDMAEN

Bit 1: Tx buffer DMA enable.

Allowed values:
0: Disabled: Tx buffer DMA disabled
1: Enabled: Tx buffer DMA enabled

SSOE

Bit 2: SS output enable.

Allowed values:
0: Disabled: SS output is disabled in master mode
1: Enabled: SS output is enabled in master mode

NSSP

Bit 3: NSS pulse management.

Allowed values:
0: NoPulse: No NSS pulse
1: PulseGenerated: NSS pulse generated

FRF

Bit 4: Frame format.

Allowed values:
0: Motorola: SPI Motorola mode
1: TI: SPI TI mode

ERRIE

Bit 5: Error interrupt enable.

Allowed values:
0: Masked: Error interrupt masked
1: NotMasked: Error interrupt not masked

RXNEIE

Bit 6: RX buffer not empty interrupt enable.

Allowed values:
0: Masked: RXE interrupt masked
1: NotMasked: RXE interrupt not masked

TXEIE

Bit 7: Tx buffer empty interrupt enable.

Allowed values:
0: Masked: TXE interrupt masked
1: NotMasked: TXE interrupt not masked

DS

Bits 8-11: Data size.

Allowed values:
3: FourBit: 4-bit
4: FiveBit: 5-bit
5: SixBit: 6-bit
6: SevenBit: 7-bit
7: EightBit: 8-bit
8: NineBit: 9-bit
9: TenBit: 10-bit
10: ElevenBit: 11-bit
11: TwelveBit: 12-bit
12: ThirteenBit: 13-bit
13: FourteenBit: 14-bit
14: FifteenBit: 15-bit
15: SixteenBit: 16-bit

FRXTH

Bit 12: FIFO reception threshold.

Allowed values:
0: Half: RXNE event is generated if the FIFO level is greater than or equal to 1/2 (16-bit)
1: Quarter: RXNE event is generated if the FIFO level is greater than or equal to 1/4 (8-bit)

LDMA_RX

Bit 13: Last DMA transfer for reception.

Allowed values:
0: Even: Number of data to transfer for receive is even
1: Odd: Number of data to transfer for receive is odd

LDMA_TX

Bit 14: Last DMA transfer for transmission.

Allowed values:
0: Even: Number of data to transfer for transmit is even
1: Odd: Number of data to transfer for transmit is odd

SR

status register

Offset: 0x8, size: 16, reset: 0x00000002, access: Unspecified

11/11 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			FTLVL r		FRLVL r		FRE r	BSY r	OVR r	MODF r	CRCERR rw	UDR r	CHSIDE r	TXE r	RXNE r

Toggle fields

RXNE

Bit 0: Receive buffer not empty.

Allowed values:
0: Empty: Rx buffer empty
1: NotEmpty: Rx buffer not empty

TXE

Bit 1: Transmit buffer empty.

Allowed values:
0: NotEmpty: Tx buffer not empty
1: Empty: Tx buffer empty

CHSIDE

Bit 2: Channel side.

Allowed values:
0: Left: Channel left has to be transmitted or has been received
1: Right: Channel right has to be transmitted or has been received

UDR

Bit 3: Underrun flag.

Allowed values:
0: NoUnderrun: No underrun occurred
1: Underrun: Underrun occurred

CRCERR

Bit 4: CRC error flag.

Allowed values:
0: Match: CRC value received matches the SPIx_RXCRCR value
1: NoMatch: CRC value received does not match the SPIx_RXCRCR value

MODF

Bit 5: Mode fault.

Allowed values:
0: NoFault: No mode fault occurred
1: Fault: Mode fault occurred

OVR

Bit 6: Overrun flag.

Allowed values:
0: NoOverrun: No overrun occurred
1: Overrun: Overrun occurred

BSY

Bit 7: Busy flag.

Allowed values:
0: NotBusy: SPI not busy
1: Busy: SPI busy

FRE

Bit 8: TI frame format error.

Allowed values:
0: NoError: No frame format error
1: Error: A frame format error occurred

FRLVL

Bits 9-10: FIFO reception level.

Allowed values:
0: Empty: Rx FIFO Empty
1: Quarter: Rx 1/4 FIFO
2: Half: Rx 1/2 FIFO
3: Full: Rx FIFO full

FTLVL

Bits 11-12: FIFO transmission level.

Allowed values:
0: Empty: Tx FIFO Empty
1: Quarter: Tx 1/4 FIFO
2: Half: Tx 1/2 FIFO
3: Full: Tx FIFO full

DR

data register

Offset: 0xc, size: 16, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DR rw

Toggle fields

DR

Bits 0-15: Data register.

Allowed values: 0x0-0xffff

DR8

Direct 8-bit access to data register

Offset: 0xc, size: 8, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								DR rw

Toggle fields

DR

Bits 0-7: Data register.

Allowed values: 0x0-0xff

CRCPR

CRC polynomial register

Offset: 0x10, size: 16, reset: 0x00000007, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CRCPOLY rw

Toggle fields

CRCPOLY

Bits 0-15: CRC polynomial register.

Allowed values: 0x0-0xffff

RXCRCR

RX CRC register

Offset: 0x14, size: 16, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RxCRC r

Toggle fields

RxCRC

Bits 0-15: Rx CRC register.

Allowed values: 0x0-0xffff

TXCRCR

TX CRC register

Offset: 0x18, size: 16, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TxCRC r

Toggle fields

TxCRC

Bits 0-15: Tx CRC register.

Allowed values: 0x0-0xffff

I2SCFGR

I2S configuration register

Offset: 0x1c, size: 16, reset: 0x00000000, access: read-write

8/8 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				I2SMOD rw	I2SE rw	I2SCFG rw		PCMSYNC rw		I2SSTD rw		CKPOL rw	DATLEN rw		CHLEN rw

Toggle fields

CHLEN

Bit 0: Channel length (number of bits per audio channel).

Allowed values:
0: SixteenBit: 16-bit wide
1: ThirtyTwoBit: 32-bit wide

DATLEN

Bits 1-2: Data length to be transferred.

Allowed values:
0: SixteenBit: 16-bit data length
1: TwentyFourBit: 24-bit data length
2: ThirtyTwoBit: 32-bit data length

CKPOL

Bit 3: Steady state clock polarity.

Allowed values:
0: IdleLow: I2S clock inactive state is low level
1: IdleHigh: I2S clock inactive state is high level

I2SSTD

Bits 4-5: I2S standard selection.

Allowed values:
0: Philips: I2S Philips standard
1: MSB: MSB justified standard
2: LSB: LSB justified standard
3: PCM: PCM standard

PCMSYNC

Bit 7: PCM frame synchronization.

Allowed values:
0: Short: Short frame synchronisation
1: Long: Long frame synchronisation

I2SCFG

Bits 8-9: I2S configuration mode.

Allowed values:
0: SlaveTx: Slave - transmit
1: SlaveRx: Slave - receive
2: MasterTx: Master - transmit
3: MasterRx: Master - receive

I2SE

Bit 10: I2S Enable.

Allowed values:
0: Disabled: I2S peripheral is disabled
1: Enabled: I2S peripheral is enabled

I2SMOD

Bit 11: I2S mode selection.

Allowed values:
0: SPIMode: SPI mode is selected
1: I2SMode: I2S mode is selected

I2SPR

I2S prescaler register

Offset: 0x20, size: 16, reset: 0x00000010, access: read-write

3/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						MCKOE rw	ODD rw	I2SDIV rw

Toggle fields

I2SDIV

Bits 0-7: I2S Linear prescaler.

Allowed values: 0x2-0xff

ODD

Bit 8: Odd factor for the prescaler.

Allowed values:
0: Even: Real divider value is I2SDIV * 2
1: Odd: Real divider value is (I2SDIV * 2) + 1

MCKOE

Bit 9: Master clock output enable.

Allowed values:
0: Disabled: Master clock output is disabled
1: Enabled: Master clock output is enabled

SPI2

0x40003800: Serial peripheral interface/Inter-IC sound

53/53 fields covered.

Toggle register map

Offset	Name	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0 (16-bit)	CR1	BIDIMODE	BIDIOE	CRCEN	CRCNEXT	CRCL	RXONLY	SSM	SSI	LSBFIRST	SPE	BR			MSTR	CPOL	CPHA
0x4 (16-bit)	CR2		LDMA_TX	LDMA_RX	FRXTH	DS				TXEIE	RXNEIE	ERRIE	FRF	NSSP	SSOE	TXDMAEN	RXDMAEN
0x8 (16-bit)	SR				FTLVL		FRLVL		FRE	BSY	OVR	MODF	CRCERR	UDR	CHSIDE	TXE	RXNE
0xc (16-bit)	DR	DR
0xc (8-bit)	DR8									DR
0x10 (16-bit)	CRCPR	CRCPOLY
0x14 (16-bit)	RXCRCR	RxCRC
0x18 (16-bit)	TXCRCR	TxCRC
0x1c (16-bit)	I2SCFGR					I2SMOD	I2SE	I2SCFG		PCMSYNC		I2SSTD		CKPOL	DATLEN		CHLEN
0x20 (16-bit)	I2SPR							MCKOE	ODD	I2SDIV

Toggle registers

CR1

control register 1

Offset: 0x0, size: 16, reset: 0x00000000, access: read-write

14/14 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BIDIMODE rw	BIDIOE rw	CRCEN rw	CRCNEXT rw	CRCL rw	RXONLY rw	SSM rw	SSI rw	LSBFIRST rw	SPE rw	BR rw			MSTR rw	CPOL rw	CPHA rw

Toggle fields

CPHA

Bit 0: Clock phase.

Allowed values:
0: FirstEdge: The first clock transition is the first data capture edge
1: SecondEdge: The second clock transition is the first data capture edge

CPOL

Bit 1: Clock polarity.

Allowed values:
0: IdleLow: CK to 0 when idle
1: IdleHigh: CK to 1 when idle

MSTR

Bit 2: Master selection.

Allowed values:
0: Slave: Slave configuration
1: Master: Master configuration

BR

Bits 3-5: Baud rate control.

Allowed values:
0: Div2: f_PCLK / 2
1: Div4: f_PCLK / 4
2: Div8: f_PCLK / 8
3: Div16: f_PCLK / 16
4: Div32: f_PCLK / 32
5: Div64: f_PCLK / 64
6: Div128: f_PCLK / 128
7: Div256: f_PCLK / 256

SPE

Bit 6: SPI enable.

Allowed values:
0: Disabled: Peripheral disabled
1: Enabled: Peripheral enabled

LSBFIRST

Bit 7: Frame format.

Allowed values:
0: MSBFirst: Data is transmitted/received with the MSB first
1: LSBFirst: Data is transmitted/received with the LSB first

SSI

Bit 8: Internal slave select.

Allowed values:
0: SlaveSelected: 0 is forced onto the NSS pin and the I/O value of the NSS pin is ignored
1: SlaveNotSelected: 1 is forced onto the NSS pin and the I/O value of the NSS pin is ignored

SSM

Bit 9: Software slave management.

Allowed values:
0: Disabled: Software slave management disabled
1: Enabled: Software slave management enabled

RXONLY

Bit 10: Receive only.

Allowed values:
0: FullDuplex: Full duplex (Transmit and receive)
1: OutputDisabled: Output disabled (Receive-only mode)

CRCL

Bit 11: CRC length.

Allowed values:
0: EightBit: 8-bit CRC length
1: SixteenBit: 16-bit CRC length

CRCNEXT

Bit 12: CRC transfer next.

Allowed values:
0: TxBuffer: Next transmit value is from Tx buffer
1: CRC: Next transmit value is from Tx CRC register

CRCEN

Bit 13: Hardware CRC calculation enable.

Allowed values:
0: Disabled: CRC calculation disabled
1: Enabled: CRC calculation enabled

BIDIOE

Bit 14: Output enable in bidirectional mode.

Allowed values:
0: OutputDisabled: Output disabled (receive-only mode)
1: OutputEnabled: Output enabled (transmit-only mode)

BIDIMODE

Bit 15: Bidirectional data mode enable.

Allowed values:
0: Unidirectional: 2-line unidirectional data mode selected
1: Bidirectional: 1-line bidirectional data mode selected

CR2

control register 2

Offset: 0x4, size: 16, reset: 0x00000000, access: read-write

12/12 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	LDMA_TX rw	LDMA_RX rw	FRXTH rw	DS rw				TXEIE rw	RXNEIE rw	ERRIE rw	FRF rw	NSSP rw	SSOE rw	TXDMAEN rw	RXDMAEN rw

Toggle fields

RXDMAEN

Bit 0: Rx buffer DMA enable.

Allowed values:
0: Disabled: Rx buffer DMA disabled
1: Enabled: Rx buffer DMA enabled

TXDMAEN

Bit 1: Tx buffer DMA enable.

Allowed values:
0: Disabled: Tx buffer DMA disabled
1: Enabled: Tx buffer DMA enabled

SSOE

Bit 2: SS output enable.

Allowed values:
0: Disabled: SS output is disabled in master mode
1: Enabled: SS output is enabled in master mode

NSSP

Bit 3: NSS pulse management.

Allowed values:
0: NoPulse: No NSS pulse
1: PulseGenerated: NSS pulse generated

FRF

Bit 4: Frame format.

Allowed values:
0: Motorola: SPI Motorola mode
1: TI: SPI TI mode

ERRIE

Bit 5: Error interrupt enable.

Allowed values:
0: Masked: Error interrupt masked
1: NotMasked: Error interrupt not masked

RXNEIE

Bit 6: RX buffer not empty interrupt enable.

Allowed values:
0: Masked: RXE interrupt masked
1: NotMasked: RXE interrupt not masked

TXEIE

Bit 7: Tx buffer empty interrupt enable.

Allowed values:
0: Masked: TXE interrupt masked
1: NotMasked: TXE interrupt not masked

DS

Bits 8-11: Data size.

Allowed values:
3: FourBit: 4-bit
4: FiveBit: 5-bit
5: SixBit: 6-bit
6: SevenBit: 7-bit
7: EightBit: 8-bit
8: NineBit: 9-bit
9: TenBit: 10-bit
10: ElevenBit: 11-bit
11: TwelveBit: 12-bit
12: ThirteenBit: 13-bit
13: FourteenBit: 14-bit
14: FifteenBit: 15-bit
15: SixteenBit: 16-bit

FRXTH

Bit 12: FIFO reception threshold.

Allowed values:
0: Half: RXNE event is generated if the FIFO level is greater than or equal to 1/2 (16-bit)
1: Quarter: RXNE event is generated if the FIFO level is greater than or equal to 1/4 (8-bit)

LDMA_RX

Bit 13: Last DMA transfer for reception.

Allowed values:
0: Even: Number of data to transfer for receive is even
1: Odd: Number of data to transfer for receive is odd

LDMA_TX

Bit 14: Last DMA transfer for transmission.

Allowed values:
0: Even: Number of data to transfer for transmit is even
1: Odd: Number of data to transfer for transmit is odd

SR

status register

Offset: 0x8, size: 16, reset: 0x00000002, access: Unspecified

11/11 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			FTLVL r		FRLVL r		FRE r	BSY r	OVR r	MODF r	CRCERR rw	UDR r	CHSIDE r	TXE r	RXNE r

Toggle fields

RXNE

Bit 0: Receive buffer not empty.

Allowed values:
0: Empty: Rx buffer empty
1: NotEmpty: Rx buffer not empty

TXE

Bit 1: Transmit buffer empty.

Allowed values:
0: NotEmpty: Tx buffer not empty
1: Empty: Tx buffer empty

CHSIDE

Bit 2: Channel side.

Allowed values:
0: Left: Channel left has to be transmitted or has been received
1: Right: Channel right has to be transmitted or has been received

UDR

Bit 3: Underrun flag.

Allowed values:
0: NoUnderrun: No underrun occurred
1: Underrun: Underrun occurred

CRCERR

Bit 4: CRC error flag.

Allowed values:
0: Match: CRC value received matches the SPIx_RXCRCR value
1: NoMatch: CRC value received does not match the SPIx_RXCRCR value

MODF

Bit 5: Mode fault.

Allowed values:
0: NoFault: No mode fault occurred
1: Fault: Mode fault occurred

OVR

Bit 6: Overrun flag.

Allowed values:
0: NoOverrun: No overrun occurred
1: Overrun: Overrun occurred

BSY

Bit 7: Busy flag.

Allowed values:
0: NotBusy: SPI not busy
1: Busy: SPI busy

FRE

Bit 8: TI frame format error.

Allowed values:
0: NoError: No frame format error
1: Error: A frame format error occurred

FRLVL

Bits 9-10: FIFO reception level.

Allowed values:
0: Empty: Rx FIFO Empty
1: Quarter: Rx 1/4 FIFO
2: Half: Rx 1/2 FIFO
3: Full: Rx FIFO full

FTLVL

Bits 11-12: FIFO transmission level.

Allowed values:
0: Empty: Tx FIFO Empty
1: Quarter: Tx 1/4 FIFO
2: Half: Tx 1/2 FIFO
3: Full: Tx FIFO full

DR

data register

Offset: 0xc, size: 16, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DR rw

Toggle fields

DR

Bits 0-15: Data register.

Allowed values: 0x0-0xffff

DR8

Direct 8-bit access to data register

Offset: 0xc, size: 8, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								DR rw

Toggle fields

DR

Bits 0-7: Data register.

Allowed values: 0x0-0xff

CRCPR

CRC polynomial register

Offset: 0x10, size: 16, reset: 0x00000007, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CRCPOLY rw

Toggle fields

CRCPOLY

Bits 0-15: CRC polynomial register.

Allowed values: 0x0-0xffff

RXCRCR

RX CRC register

Offset: 0x14, size: 16, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RxCRC r

Toggle fields

RxCRC

Bits 0-15: Rx CRC register.

Allowed values: 0x0-0xffff

TXCRCR

TX CRC register

Offset: 0x18, size: 16, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TxCRC r

Toggle fields

TxCRC

Bits 0-15: Tx CRC register.

Allowed values: 0x0-0xffff

I2SCFGR

I2S configuration register

Offset: 0x1c, size: 16, reset: 0x00000000, access: read-write

8/8 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				I2SMOD rw	I2SE rw	I2SCFG rw		PCMSYNC rw		I2SSTD rw		CKPOL rw	DATLEN rw		CHLEN rw

Toggle fields

CHLEN

Bit 0: Channel length (number of bits per audio channel).

Allowed values:
0: SixteenBit: 16-bit wide
1: ThirtyTwoBit: 32-bit wide

DATLEN

Bits 1-2: Data length to be transferred.

Allowed values:
0: SixteenBit: 16-bit data length
1: TwentyFourBit: 24-bit data length
2: ThirtyTwoBit: 32-bit data length

CKPOL

Bit 3: Steady state clock polarity.

Allowed values:
0: IdleLow: I2S clock inactive state is low level
1: IdleHigh: I2S clock inactive state is high level

I2SSTD

Bits 4-5: I2S standard selection.

Allowed values:
0: Philips: I2S Philips standard
1: MSB: MSB justified standard
2: LSB: LSB justified standard
3: PCM: PCM standard

PCMSYNC

Bit 7: PCM frame synchronization.

Allowed values:
0: Short: Short frame synchronisation
1: Long: Long frame synchronisation

I2SCFG

Bits 8-9: I2S configuration mode.

Allowed values:
0: SlaveTx: Slave - transmit
1: SlaveRx: Slave - receive
2: MasterTx: Master - transmit
3: MasterRx: Master - receive

I2SE

Bit 10: I2S Enable.

Allowed values:
0: Disabled: I2S peripheral is disabled
1: Enabled: I2S peripheral is enabled

I2SMOD

Bit 11: I2S mode selection.

Allowed values:
0: SPIMode: SPI mode is selected
1: I2SMode: I2S mode is selected

I2SPR

I2S prescaler register

Offset: 0x20, size: 16, reset: 0x00000010, access: read-write

3/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						MCKOE rw	ODD rw	I2SDIV rw

Toggle fields

I2SDIV

Bits 0-7: I2S Linear prescaler.

Allowed values: 0x2-0xff

ODD

Bit 8: Odd factor for the prescaler.

Allowed values:
0: Even: Real divider value is I2SDIV * 2
1: Odd: Real divider value is (I2SDIV * 2) + 1

MCKOE

Bit 9: Master clock output enable.

Allowed values:
0: Disabled: Master clock output is disabled
1: Enabled: Master clock output is enabled

SPI3

0x40003c00: Serial peripheral interface/Inter-IC sound

53/53 fields covered.

Toggle register map

Offset	Name	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0 (16-bit)	CR1	BIDIMODE	BIDIOE	CRCEN	CRCNEXT	CRCL	RXONLY	SSM	SSI	LSBFIRST	SPE	BR			MSTR	CPOL	CPHA
0x4 (16-bit)	CR2		LDMA_TX	LDMA_RX	FRXTH	DS				TXEIE	RXNEIE	ERRIE	FRF	NSSP	SSOE	TXDMAEN	RXDMAEN
0x8 (16-bit)	SR				FTLVL		FRLVL		FRE	BSY	OVR	MODF	CRCERR	UDR	CHSIDE	TXE	RXNE
0xc (16-bit)	DR	DR
0xc (8-bit)	DR8									DR
0x10 (16-bit)	CRCPR	CRCPOLY
0x14 (16-bit)	RXCRCR	RxCRC
0x18 (16-bit)	TXCRCR	TxCRC
0x1c (16-bit)	I2SCFGR					I2SMOD	I2SE	I2SCFG		PCMSYNC		I2SSTD		CKPOL	DATLEN		CHLEN
0x20 (16-bit)	I2SPR							MCKOE	ODD	I2SDIV

Toggle registers

CR1

control register 1

Offset: 0x0, size: 16, reset: 0x00000000, access: read-write

14/14 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BIDIMODE rw	BIDIOE rw	CRCEN rw	CRCNEXT rw	CRCL rw	RXONLY rw	SSM rw	SSI rw	LSBFIRST rw	SPE rw	BR rw			MSTR rw	CPOL rw	CPHA rw

Toggle fields

CPHA

Bit 0: Clock phase.

Allowed values:
0: FirstEdge: The first clock transition is the first data capture edge
1: SecondEdge: The second clock transition is the first data capture edge

CPOL

Bit 1: Clock polarity.

Allowed values:
0: IdleLow: CK to 0 when idle
1: IdleHigh: CK to 1 when idle

MSTR

Bit 2: Master selection.

Allowed values:
0: Slave: Slave configuration
1: Master: Master configuration

BR

Bits 3-5: Baud rate control.

Allowed values:
0: Div2: f_PCLK / 2
1: Div4: f_PCLK / 4
2: Div8: f_PCLK / 8
3: Div16: f_PCLK / 16
4: Div32: f_PCLK / 32
5: Div64: f_PCLK / 64
6: Div128: f_PCLK / 128
7: Div256: f_PCLK / 256

SPE

Bit 6: SPI enable.

Allowed values:
0: Disabled: Peripheral disabled
1: Enabled: Peripheral enabled

LSBFIRST

Bit 7: Frame format.

Allowed values:
0: MSBFirst: Data is transmitted/received with the MSB first
1: LSBFirst: Data is transmitted/received with the LSB first

SSI

Bit 8: Internal slave select.

Allowed values:
0: SlaveSelected: 0 is forced onto the NSS pin and the I/O value of the NSS pin is ignored
1: SlaveNotSelected: 1 is forced onto the NSS pin and the I/O value of the NSS pin is ignored

SSM

Bit 9: Software slave management.

Allowed values:
0: Disabled: Software slave management disabled
1: Enabled: Software slave management enabled

RXONLY

Bit 10: Receive only.

Allowed values:
0: FullDuplex: Full duplex (Transmit and receive)
1: OutputDisabled: Output disabled (Receive-only mode)

CRCL

Bit 11: CRC length.

Allowed values:
0: EightBit: 8-bit CRC length
1: SixteenBit: 16-bit CRC length

CRCNEXT

Bit 12: CRC transfer next.

Allowed values:
0: TxBuffer: Next transmit value is from Tx buffer
1: CRC: Next transmit value is from Tx CRC register

CRCEN

Bit 13: Hardware CRC calculation enable.

Allowed values:
0: Disabled: CRC calculation disabled
1: Enabled: CRC calculation enabled

BIDIOE

Bit 14: Output enable in bidirectional mode.

Allowed values:
0: OutputDisabled: Output disabled (receive-only mode)
1: OutputEnabled: Output enabled (transmit-only mode)

BIDIMODE

Bit 15: Bidirectional data mode enable.

Allowed values:
0: Unidirectional: 2-line unidirectional data mode selected
1: Bidirectional: 1-line bidirectional data mode selected

CR2

control register 2

Offset: 0x4, size: 16, reset: 0x00000000, access: read-write

12/12 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	LDMA_TX rw	LDMA_RX rw	FRXTH rw	DS rw				TXEIE rw	RXNEIE rw	ERRIE rw	FRF rw	NSSP rw	SSOE rw	TXDMAEN rw	RXDMAEN rw

Toggle fields

RXDMAEN

Bit 0: Rx buffer DMA enable.

Allowed values:
0: Disabled: Rx buffer DMA disabled
1: Enabled: Rx buffer DMA enabled

TXDMAEN

Bit 1: Tx buffer DMA enable.

Allowed values:
0: Disabled: Tx buffer DMA disabled
1: Enabled: Tx buffer DMA enabled

SSOE

Bit 2: SS output enable.

Allowed values:
0: Disabled: SS output is disabled in master mode
1: Enabled: SS output is enabled in master mode

NSSP

Bit 3: NSS pulse management.

Allowed values:
0: NoPulse: No NSS pulse
1: PulseGenerated: NSS pulse generated

FRF

Bit 4: Frame format.

Allowed values:
0: Motorola: SPI Motorola mode
1: TI: SPI TI mode

ERRIE

Bit 5: Error interrupt enable.

Allowed values:
0: Masked: Error interrupt masked
1: NotMasked: Error interrupt not masked

RXNEIE

Bit 6: RX buffer not empty interrupt enable.

Allowed values:
0: Masked: RXE interrupt masked
1: NotMasked: RXE interrupt not masked

TXEIE

Bit 7: Tx buffer empty interrupt enable.

Allowed values:
0: Masked: TXE interrupt masked
1: NotMasked: TXE interrupt not masked

DS

Bits 8-11: Data size.

Allowed values:
3: FourBit: 4-bit
4: FiveBit: 5-bit
5: SixBit: 6-bit
6: SevenBit: 7-bit
7: EightBit: 8-bit
8: NineBit: 9-bit
9: TenBit: 10-bit
10: ElevenBit: 11-bit
11: TwelveBit: 12-bit
12: ThirteenBit: 13-bit
13: FourteenBit: 14-bit
14: FifteenBit: 15-bit
15: SixteenBit: 16-bit

FRXTH

Bit 12: FIFO reception threshold.

Allowed values:
0: Half: RXNE event is generated if the FIFO level is greater than or equal to 1/2 (16-bit)
1: Quarter: RXNE event is generated if the FIFO level is greater than or equal to 1/4 (8-bit)

LDMA_RX

Bit 13: Last DMA transfer for reception.

Allowed values:
0: Even: Number of data to transfer for receive is even
1: Odd: Number of data to transfer for receive is odd

LDMA_TX

Bit 14: Last DMA transfer for transmission.

Allowed values:
0: Even: Number of data to transfer for transmit is even
1: Odd: Number of data to transfer for transmit is odd

SR

status register

Offset: 0x8, size: 16, reset: 0x00000002, access: Unspecified

11/11 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			FTLVL r		FRLVL r		FRE r	BSY r	OVR r	MODF r	CRCERR rw	UDR r	CHSIDE r	TXE r	RXNE r

Toggle fields

RXNE

Bit 0: Receive buffer not empty.

Allowed values:
0: Empty: Rx buffer empty
1: NotEmpty: Rx buffer not empty

TXE

Bit 1: Transmit buffer empty.

Allowed values:
0: NotEmpty: Tx buffer not empty
1: Empty: Tx buffer empty

CHSIDE

Bit 2: Channel side.

Allowed values:
0: Left: Channel left has to be transmitted or has been received
1: Right: Channel right has to be transmitted or has been received

UDR

Bit 3: Underrun flag.

Allowed values:
0: NoUnderrun: No underrun occurred
1: Underrun: Underrun occurred

CRCERR

Bit 4: CRC error flag.

Allowed values:
0: Match: CRC value received matches the SPIx_RXCRCR value
1: NoMatch: CRC value received does not match the SPIx_RXCRCR value

MODF

Bit 5: Mode fault.

Allowed values:
0: NoFault: No mode fault occurred
1: Fault: Mode fault occurred

OVR

Bit 6: Overrun flag.

Allowed values:
0: NoOverrun: No overrun occurred
1: Overrun: Overrun occurred

BSY

Bit 7: Busy flag.

Allowed values:
0: NotBusy: SPI not busy
1: Busy: SPI busy

FRE

Bit 8: TI frame format error.

Allowed values:
0: NoError: No frame format error
1: Error: A frame format error occurred

FRLVL

Bits 9-10: FIFO reception level.

Allowed values:
0: Empty: Rx FIFO Empty
1: Quarter: Rx 1/4 FIFO
2: Half: Rx 1/2 FIFO
3: Full: Rx FIFO full

FTLVL

Bits 11-12: FIFO transmission level.

Allowed values:
0: Empty: Tx FIFO Empty
1: Quarter: Tx 1/4 FIFO
2: Half: Tx 1/2 FIFO
3: Full: Tx FIFO full

DR

data register

Offset: 0xc, size: 16, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DR rw

Toggle fields

DR

Bits 0-15: Data register.

Allowed values: 0x0-0xffff

DR8

Direct 8-bit access to data register

Offset: 0xc, size: 8, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								DR rw

Toggle fields

DR

Bits 0-7: Data register.

Allowed values: 0x0-0xff

CRCPR

CRC polynomial register

Offset: 0x10, size: 16, reset: 0x00000007, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CRCPOLY rw

Toggle fields

CRCPOLY

Bits 0-15: CRC polynomial register.

Allowed values: 0x0-0xffff

RXCRCR

RX CRC register

Offset: 0x14, size: 16, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RxCRC r

Toggle fields

RxCRC

Bits 0-15: Rx CRC register.

Allowed values: 0x0-0xffff

TXCRCR

TX CRC register

Offset: 0x18, size: 16, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TxCRC r

Toggle fields

TxCRC

Bits 0-15: Tx CRC register.

Allowed values: 0x0-0xffff

I2SCFGR

I2S configuration register

Offset: 0x1c, size: 16, reset: 0x00000000, access: read-write

8/8 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				I2SMOD rw	I2SE rw	I2SCFG rw		PCMSYNC rw		I2SSTD rw		CKPOL rw	DATLEN rw		CHLEN rw

Toggle fields

CHLEN

Bit 0: Channel length (number of bits per audio channel).

Allowed values:
0: SixteenBit: 16-bit wide
1: ThirtyTwoBit: 32-bit wide

DATLEN

Bits 1-2: Data length to be transferred.

Allowed values:
0: SixteenBit: 16-bit data length
1: TwentyFourBit: 24-bit data length
2: ThirtyTwoBit: 32-bit data length

CKPOL

Bit 3: Steady state clock polarity.

Allowed values:
0: IdleLow: I2S clock inactive state is low level
1: IdleHigh: I2S clock inactive state is high level

I2SSTD

Bits 4-5: I2S standard selection.

Allowed values:
0: Philips: I2S Philips standard
1: MSB: MSB justified standard
2: LSB: LSB justified standard
3: PCM: PCM standard

PCMSYNC

Bit 7: PCM frame synchronization.

Allowed values:
0: Short: Short frame synchronisation
1: Long: Long frame synchronisation

I2SCFG

Bits 8-9: I2S configuration mode.

Allowed values:
0: SlaveTx: Slave - transmit
1: SlaveRx: Slave - receive
2: MasterTx: Master - transmit
3: MasterRx: Master - receive

I2SE

Bit 10: I2S Enable.

Allowed values:
0: Disabled: I2S peripheral is disabled
1: Enabled: I2S peripheral is enabled

I2SMOD

Bit 11: I2S mode selection.

Allowed values:
0: SPIMode: SPI mode is selected
1: I2SMode: I2S mode is selected

I2SPR

I2S prescaler register

Offset: 0x20, size: 16, reset: 0x00000010, access: read-write

3/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						MCKOE rw	ODD rw	I2SDIV rw

Toggle fields

I2SDIV

Bits 0-7: I2S Linear prescaler.

Allowed values: 0x2-0xff

ODD

Bit 8: Odd factor for the prescaler.

Allowed values:
0: Even: Real divider value is I2SDIV * 2
1: Odd: Real divider value is (I2SDIV * 2) + 1

MCKOE

Bit 9: Master clock output enable.

Allowed values:
0: Disabled: Master clock output is disabled
1: Enabled: Master clock output is enabled

SPI4

0x40013c00: Serial peripheral interface/Inter-IC sound

53/53 fields covered.

Toggle register map

Offset	Name	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0 (16-bit)	CR1	BIDIMODE	BIDIOE	CRCEN	CRCNEXT	CRCL	RXONLY	SSM	SSI	LSBFIRST	SPE	BR			MSTR	CPOL	CPHA
0x4 (16-bit)	CR2		LDMA_TX	LDMA_RX	FRXTH	DS				TXEIE	RXNEIE	ERRIE	FRF	NSSP	SSOE	TXDMAEN	RXDMAEN
0x8 (16-bit)	SR				FTLVL		FRLVL		FRE	BSY	OVR	MODF	CRCERR	UDR	CHSIDE	TXE	RXNE
0xc (16-bit)	DR	DR
0xc (8-bit)	DR8									DR
0x10 (16-bit)	CRCPR	CRCPOLY
0x14 (16-bit)	RXCRCR	RxCRC
0x18 (16-bit)	TXCRCR	TxCRC
0x1c (16-bit)	I2SCFGR					I2SMOD	I2SE	I2SCFG		PCMSYNC		I2SSTD		CKPOL	DATLEN		CHLEN
0x20 (16-bit)	I2SPR							MCKOE	ODD	I2SDIV

Toggle registers

CR1

control register 1

Offset: 0x0, size: 16, reset: 0x00000000, access: read-write

14/14 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BIDIMODE rw	BIDIOE rw	CRCEN rw	CRCNEXT rw	CRCL rw	RXONLY rw	SSM rw	SSI rw	LSBFIRST rw	SPE rw	BR rw			MSTR rw	CPOL rw	CPHA rw

Toggle fields

CPHA

Bit 0: Clock phase.

Allowed values:
0: FirstEdge: The first clock transition is the first data capture edge
1: SecondEdge: The second clock transition is the first data capture edge

CPOL

Bit 1: Clock polarity.

Allowed values:
0: IdleLow: CK to 0 when idle
1: IdleHigh: CK to 1 when idle

MSTR

Bit 2: Master selection.

Allowed values:
0: Slave: Slave configuration
1: Master: Master configuration

BR

Bits 3-5: Baud rate control.

Allowed values:
0: Div2: f_PCLK / 2
1: Div4: f_PCLK / 4
2: Div8: f_PCLK / 8
3: Div16: f_PCLK / 16
4: Div32: f_PCLK / 32
5: Div64: f_PCLK / 64
6: Div128: f_PCLK / 128
7: Div256: f_PCLK / 256

SPE

Bit 6: SPI enable.

Allowed values:
0: Disabled: Peripheral disabled
1: Enabled: Peripheral enabled

LSBFIRST

Bit 7: Frame format.

Allowed values:
0: MSBFirst: Data is transmitted/received with the MSB first
1: LSBFirst: Data is transmitted/received with the LSB first

SSI

Bit 8: Internal slave select.

Allowed values:
0: SlaveSelected: 0 is forced onto the NSS pin and the I/O value of the NSS pin is ignored
1: SlaveNotSelected: 1 is forced onto the NSS pin and the I/O value of the NSS pin is ignored

SSM

Bit 9: Software slave management.

Allowed values:
0: Disabled: Software slave management disabled
1: Enabled: Software slave management enabled

RXONLY

Bit 10: Receive only.

Allowed values:
0: FullDuplex: Full duplex (Transmit and receive)
1: OutputDisabled: Output disabled (Receive-only mode)

CRCL

Bit 11: CRC length.

Allowed values:
0: EightBit: 8-bit CRC length
1: SixteenBit: 16-bit CRC length

CRCNEXT

Bit 12: CRC transfer next.

Allowed values:
0: TxBuffer: Next transmit value is from Tx buffer
1: CRC: Next transmit value is from Tx CRC register

CRCEN

Bit 13: Hardware CRC calculation enable.

Allowed values:
0: Disabled: CRC calculation disabled
1: Enabled: CRC calculation enabled

BIDIOE

Bit 14: Output enable in bidirectional mode.

Allowed values:
0: OutputDisabled: Output disabled (receive-only mode)
1: OutputEnabled: Output enabled (transmit-only mode)

BIDIMODE

Bit 15: Bidirectional data mode enable.

Allowed values:
0: Unidirectional: 2-line unidirectional data mode selected
1: Bidirectional: 1-line bidirectional data mode selected

CR2

control register 2

Offset: 0x4, size: 16, reset: 0x00000000, access: read-write

12/12 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	LDMA_TX rw	LDMA_RX rw	FRXTH rw	DS rw				TXEIE rw	RXNEIE rw	ERRIE rw	FRF rw	NSSP rw	SSOE rw	TXDMAEN rw	RXDMAEN rw

Toggle fields

RXDMAEN

Bit 0: Rx buffer DMA enable.

Allowed values:
0: Disabled: Rx buffer DMA disabled
1: Enabled: Rx buffer DMA enabled

TXDMAEN

Bit 1: Tx buffer DMA enable.

Allowed values:
0: Disabled: Tx buffer DMA disabled
1: Enabled: Tx buffer DMA enabled

SSOE

Bit 2: SS output enable.

Allowed values:
0: Disabled: SS output is disabled in master mode
1: Enabled: SS output is enabled in master mode

NSSP

Bit 3: NSS pulse management.

Allowed values:
0: NoPulse: No NSS pulse
1: PulseGenerated: NSS pulse generated

FRF

Bit 4: Frame format.

Allowed values:
0: Motorola: SPI Motorola mode
1: TI: SPI TI mode

ERRIE

Bit 5: Error interrupt enable.

Allowed values:
0: Masked: Error interrupt masked
1: NotMasked: Error interrupt not masked

RXNEIE

Bit 6: RX buffer not empty interrupt enable.

Allowed values:
0: Masked: RXE interrupt masked
1: NotMasked: RXE interrupt not masked

TXEIE

Bit 7: Tx buffer empty interrupt enable.

Allowed values:
0: Masked: TXE interrupt masked
1: NotMasked: TXE interrupt not masked

DS

Bits 8-11: Data size.

Allowed values:
3: FourBit: 4-bit
4: FiveBit: 5-bit
5: SixBit: 6-bit
6: SevenBit: 7-bit
7: EightBit: 8-bit
8: NineBit: 9-bit
9: TenBit: 10-bit
10: ElevenBit: 11-bit
11: TwelveBit: 12-bit
12: ThirteenBit: 13-bit
13: FourteenBit: 14-bit
14: FifteenBit: 15-bit
15: SixteenBit: 16-bit

FRXTH

Bit 12: FIFO reception threshold.

Allowed values:
0: Half: RXNE event is generated if the FIFO level is greater than or equal to 1/2 (16-bit)
1: Quarter: RXNE event is generated if the FIFO level is greater than or equal to 1/4 (8-bit)

LDMA_RX

Bit 13: Last DMA transfer for reception.

Allowed values:
0: Even: Number of data to transfer for receive is even
1: Odd: Number of data to transfer for receive is odd

LDMA_TX

Bit 14: Last DMA transfer for transmission.

Allowed values:
0: Even: Number of data to transfer for transmit is even
1: Odd: Number of data to transfer for transmit is odd

SR

status register

Offset: 0x8, size: 16, reset: 0x00000002, access: Unspecified

11/11 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			FTLVL r		FRLVL r		FRE r	BSY r	OVR r	MODF r	CRCERR rw	UDR r	CHSIDE r	TXE r	RXNE r

Toggle fields

RXNE

Bit 0: Receive buffer not empty.

Allowed values:
0: Empty: Rx buffer empty
1: NotEmpty: Rx buffer not empty

TXE

Bit 1: Transmit buffer empty.

Allowed values:
0: NotEmpty: Tx buffer not empty
1: Empty: Tx buffer empty

CHSIDE

Bit 2: Channel side.

Allowed values:
0: Left: Channel left has to be transmitted or has been received
1: Right: Channel right has to be transmitted or has been received

UDR

Bit 3: Underrun flag.

Allowed values:
0: NoUnderrun: No underrun occurred
1: Underrun: Underrun occurred

CRCERR

Bit 4: CRC error flag.

Allowed values:
0: Match: CRC value received matches the SPIx_RXCRCR value
1: NoMatch: CRC value received does not match the SPIx_RXCRCR value

MODF

Bit 5: Mode fault.

Allowed values:
0: NoFault: No mode fault occurred
1: Fault: Mode fault occurred

OVR

Bit 6: Overrun flag.

Allowed values:
0: NoOverrun: No overrun occurred
1: Overrun: Overrun occurred

BSY

Bit 7: Busy flag.

Allowed values:
0: NotBusy: SPI not busy
1: Busy: SPI busy

FRE

Bit 8: TI frame format error.

Allowed values:
0: NoError: No frame format error
1: Error: A frame format error occurred

FRLVL

Bits 9-10: FIFO reception level.

Allowed values:
0: Empty: Rx FIFO Empty
1: Quarter: Rx 1/4 FIFO
2: Half: Rx 1/2 FIFO
3: Full: Rx FIFO full

FTLVL

Bits 11-12: FIFO transmission level.

Allowed values:
0: Empty: Tx FIFO Empty
1: Quarter: Tx 1/4 FIFO
2: Half: Tx 1/2 FIFO
3: Full: Tx FIFO full

DR

data register

Offset: 0xc, size: 16, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DR rw

Toggle fields

DR

Bits 0-15: Data register.

Allowed values: 0x0-0xffff

DR8

Direct 8-bit access to data register

Offset: 0xc, size: 8, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								DR rw

Toggle fields

DR

Bits 0-7: Data register.

Allowed values: 0x0-0xff

CRCPR

CRC polynomial register

Offset: 0x10, size: 16, reset: 0x00000007, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CRCPOLY rw

Toggle fields

CRCPOLY

Bits 0-15: CRC polynomial register.

Allowed values: 0x0-0xffff

RXCRCR

RX CRC register

Offset: 0x14, size: 16, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RxCRC r

Toggle fields

RxCRC

Bits 0-15: Rx CRC register.

Allowed values: 0x0-0xffff

TXCRCR

TX CRC register

Offset: 0x18, size: 16, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TxCRC r

Toggle fields

TxCRC

Bits 0-15: Tx CRC register.

Allowed values: 0x0-0xffff

I2SCFGR

I2S configuration register

Offset: 0x1c, size: 16, reset: 0x00000000, access: read-write

8/8 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				I2SMOD rw	I2SE rw	I2SCFG rw		PCMSYNC rw		I2SSTD rw		CKPOL rw	DATLEN rw		CHLEN rw

Toggle fields

CHLEN

Bit 0: Channel length (number of bits per audio channel).

Allowed values:
0: SixteenBit: 16-bit wide
1: ThirtyTwoBit: 32-bit wide

DATLEN

Bits 1-2: Data length to be transferred.

Allowed values:
0: SixteenBit: 16-bit data length
1: TwentyFourBit: 24-bit data length
2: ThirtyTwoBit: 32-bit data length

CKPOL

Bit 3: Steady state clock polarity.

Allowed values:
0: IdleLow: I2S clock inactive state is low level
1: IdleHigh: I2S clock inactive state is high level

I2SSTD

Bits 4-5: I2S standard selection.

Allowed values:
0: Philips: I2S Philips standard
1: MSB: MSB justified standard
2: LSB: LSB justified standard
3: PCM: PCM standard

PCMSYNC

Bit 7: PCM frame synchronization.

Allowed values:
0: Short: Short frame synchronisation
1: Long: Long frame synchronisation

I2SCFG

Bits 8-9: I2S configuration mode.

Allowed values:
0: SlaveTx: Slave - transmit
1: SlaveRx: Slave - receive
2: MasterTx: Master - transmit
3: MasterRx: Master - receive

I2SE

Bit 10: I2S Enable.

Allowed values:
0: Disabled: I2S peripheral is disabled
1: Enabled: I2S peripheral is enabled

I2SMOD

Bit 11: I2S mode selection.

Allowed values:
0: SPIMode: SPI mode is selected
1: I2SMode: I2S mode is selected

I2SPR

I2S prescaler register

Offset: 0x20, size: 16, reset: 0x00000010, access: read-write

3/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						MCKOE rw	ODD rw	I2SDIV rw

Toggle fields

I2SDIV

Bits 0-7: I2S Linear prescaler.

Allowed values: 0x2-0xff

ODD

Bit 8: Odd factor for the prescaler.

Allowed values:
0: Even: Real divider value is I2SDIV * 2
1: Odd: Real divider value is (I2SDIV * 2) + 1

MCKOE

Bit 9: Master clock output enable.

Allowed values:
0: Disabled: Master clock output is disabled
1: Enabled: Master clock output is enabled

STK

0xe000e010: SysTick timer

0/9 fields covered.

Toggle register map

Offset	Name	31	30	23	16	15	2	1	0
0x0	CTRL				COUNTFLAG		CLKSOURCE	TICKINT	ENABLE
0x4	LOAD			RELOAD		RELOAD
0x8	VAL			CURRENT		CURRENT
0xc	CALIB	NOREF	SKEW	TENMS		TENMS

Toggle registers

CTRL

SysTick control and status register

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															COUNTFLAG rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
													CLKSOURCE rw	TICKINT rw	ENABLE rw

Toggle fields

ENABLE

Bit 0: Counter enable.

TICKINT

Bit 1: SysTick exception request enable.

CLKSOURCE

Bit 2: Clock source selection.

COUNTFLAG

Bit 16: COUNTFLAG.

LOAD

SysTick reload value register

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								RELOAD rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RELOAD rw

Toggle fields

RELOAD

Bits 0-23: RELOAD value.

VAL

SysTick current value register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								CURRENT rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CURRENT rw

Toggle fields

CURRENT

Bits 0-23: Current counter value.

CALIB

SysTick calibration value register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

0/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
NOREF rw	SKEW rw							TENMS rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TENMS rw

Toggle fields

TENMS

Bits 0-23: Calibration value.

SKEW

Bit 30: SKEW flag: Indicates whether the TENMS value is exact.

NOREF

Bit 31: NOREF flag. Reads as zero.

SYSCFG

0x40010000: System configuration controller

80/80 fields covered.

Toggle register map

Offset	Name	31	30	29	28	27	26	24	23	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	CFGR1	FPU_IE5	FPU_IE4	FPU_IE3	FPU_IE2	FPU_IE1	FPU_IE0	I2C3_FMP	ENCODER_MODE	I2C2_FMP	I2C1_FMP	I2C_PB9_FMP	I2C_PB8_FMP	I2C_PB7_FMP	I2C_PB6_FMP	DAC2_CH1_DMA_RMP	TIM7_DAC1_CH2_DMA_RMP	TIM6_DAC1_CH1_DMA_RMP	TIM17_DMA_RMP	TIM16_DMA_RMP			ADC2_DMA_RMP	DAC1_TRIG_RMP	TIM1_ITR3_RMP	USB_IT_RMP			MEM_MODE
0x4	RCR															PAGE15_WP	PAGE14_WP	PAGE13_WP	PAGE12_WP	PAGE11_WP	PAGE10_WP	PAGE9_WP	PAGE8_WP	PAGE7_WP	PAGE6_WP	PAGE5_WP	PAGE4_WP	PAGE3_WP	PAGE2_WP	PAGE1_WP	PAGE0_WP
0x8	EXTICR1															EXTI3				EXTI2				EXTI1				EXTI0
0xc	EXTICR2															EXTI7				EXTI6				EXTI5				EXTI4
0x10	EXTICR3															EXTI11				EXTI10				EXTI9				EXTI8
0x14	EXTICR4															EXTI15				EXTI14				EXTI13				EXTI12
0x18	CFGR2																						SRAM_PEF				BYP_ADDR_PAR		PVD_LOCK	SRAM_PARITY_LOCK	LOCKUP_LOCK
0x48	CFGR4																	ADC34_JEXT14_RMP	ADC34_JEXT11_RMP	ADC34_JEXT5_RMP	ADC34_EXT15_RMP	ADC34_EXT6_RMP	ADC34_EXT5_RMP	ADC12_JEXT13_RMP	ADC12_JEXT6_RMP	ADC12_JEXT3_RMP	ADC12_EXT15_RMP	ADC12_EXT13_RMP	ADC12_EXT5_RMP	ADC12_EXT3_RMP	ADC12_EXT2_RMP
0x50	CFGR3																					ADC2_DMA_RMP		I2C1_TX_DMA_RMP		I2C1_RX_DMA_RMP		SPI1_TX_DMA_RMP		SPI1_RX_DMA_RMP

Toggle registers

CFGR1

configuration register 1

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

24/24 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FPU_IE5 rw	FPU_IE4 rw	FPU_IE3 rw	FPU_IE2 rw	FPU_IE1 rw	FPU_IE0 rw		I2C3_FMP rw	ENCODER_MODE rw		I2C2_FMP rw	I2C1_FMP rw	I2C_PB9_FMP rw	I2C_PB8_FMP rw	I2C_PB7_FMP rw	I2C_PB6_FMP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DAC2_CH1_DMA_RMP rw	TIM7_DAC1_CH2_DMA_RMP rw	TIM6_DAC1_CH1_DMA_RMP rw	TIM17_DMA_RMP rw	TIM16_DMA_RMP rw			ADC2_DMA_RMP rw	DAC1_TRIG_RMP rw	TIM1_ITR3_RMP rw	USB_IT_RMP rw			MEM_MODE rw

Toggle fields

MEM_MODE

Bits 0-2: Memory mapping selection bits.

Allowed values:
0: MainFlash: Main Flash memory mapped at 0x0000_0000
1: SystemFlash: System Flash memory mapped at 0x0000_0000
3: SRAM: Embedded SRAM mapped at 0x0000_0000
4: FMC: FMC Bank (Only the first two banks) (Available on STM32F303xD/E only)

USB_IT_RMP

Bit 5: USB interrupt remap.

Allowed values:
0: NotRemapped: USB_HP, USB_LP and USB_WAKEUP interrupts are mapped on interrupt lines 19, 20 and 42 respectively
1: Remapped: USB_HP, USB_LP and USB_WAKEUP interrupts are mapped on interrupt lines 74, 75 and 76 respectively

TIM1_ITR3_RMP

Bit 6: Timer 1 ITR3 selection.

Allowed values:
0: NotRemapped: TIM1_ITR3 = TIM4_TRGO in STM32F303xB/C and STM32F358xC devices
1: Remapped: TIM1_ITR3 = TIM17_OC

DAC1_TRIG_RMP

Bit 7: DAC trigger remap (when TSEL = 001).

Allowed values:
0: NotRemapped: DAC trigger is TIM8_TRGO in STM32F303xB/C and STM32F358xC devices
1: Remapped: DAC trigger is TIM3_TRGO

ADC2_DMA_RMP

Bit 8: ADC24 DMA remapping bit.

Allowed values:
0: NotRemapped: ADC24 DMA requests mapped on DMA2 channels 1 and 2
1: Remapped: ADC24 DMA requests mapped on DMA2 channels 3 and 4

TIM16_DMA_RMP

Bit 11: TIM16 DMA request remapping bit.

Allowed values:
0: NotRemapped: TIM16_CH1 and TIM16_UP DMA requests mapped on DMA channel 3
1: Remapped: TIM16_CH1 and TIM16_UP DMA requests mapped on DMA channel 4

TIM17_DMA_RMP

Bit 12: TIM17 DMA request remapping bit.

Allowed values:
0: NotRemapped: TIM17_CH1 and TIM17_UP DMA requests mapped on DMA channel 1
1: Remapped: TIM17_CH1 and TIM17_UP DMA requests mapped on DMA channel 2

TIM6_DAC1_CH1_DMA_RMP

Bit 13: TIM6 and DAC1 DMA request remapping bit.

Allowed values:
0: NotRemapped: TIM6_UP and DAC_CH1 DMA requests mapped on DMA2 channel 3 in STM32F303xB/C and STM32F358xC
1: Remapped: TIM6_UP and DAC_CH1 DMA requests mapped on DMA1 channel 3

TIM7_DAC1_CH2_DMA_RMP

Bit 14: TIM7 and DAC2 DMA request remapping bit.

Allowed values:
0: NotRemapped: TIM7_UP and DAC_CH2 DMA requests mapped on DMA2 channel 4 in STM32F303xB/C and STM32F358xC devices
1: Remapped: TIM7_UP and DAC_CH2 DMA requests mapped on DMA1 channel 4

DAC2_CH1_DMA_RMP

Bit 15: DAC2 channel1 DMA remap.

Allowed values:
0: NotRemapped: Not remapped
1: Remapped: DAC2_CH1 DMA requests mapped on DMA1 channel 5

I2C_PB6_FMP

Bit 16: Fast Mode Plus (FM+) driving capability activation bits..

Allowed values:
0: Standard: PB6 pin operate in standard mode
1: FMP: I2C FM+ mode enabled on PB6 and the Speed control is bypassed

I2C_PB7_FMP

Bit 17: Fast Mode Plus (FM+) driving capability activation bits..

Allowed values:
0: Standard: PB7 pin operate in standard mode
1: FMP: I2C FM+ mode enabled on PB7 and the Speed control is bypassed

I2C_PB8_FMP

Bit 18: Fast Mode Plus (FM+) driving capability activation bits..

Allowed values:
0: Standard: PB8 pin operate in standard mode
1: FMP: I2C FM+ mode enabled on PB8 and the Speed control is bypassed

I2C_PB9_FMP

Bit 19: Fast Mode Plus (FM+) driving capability activation bits..

Allowed values:
0: Standard: PB9 pin operate in standard mode
1: FMP: I2C FM+ mode enabled on PB9 and the Speed control is bypassed

I2C1_FMP

Bit 20: I2C1 Fast Mode Plus.

Allowed values:
0: Standard: FM+ mode is controlled by I2C_Pxx_FMP bits only
1: FMP: FM+ mode is enabled on all I2C1 pins selected through selection through IOPORT control registers AF selection bits

I2C2_FMP

Bit 21: I2C2 Fast Mode Plus.

Allowed values:
0: Standard: FM+ mode is controlled by I2C_Pxx_FMP bits only
1: FMP: FM+ mode is enabled on all I2C2 pins selected through selection through IOPORT control registers AF selection bits

ENCODER_MODE

Bits 22-23: Encoder mode.

Allowed values:
0: NoRedirection: No redirection
1: MapTim2Tim15: TIM2 IC1 and TIM2 IC2 are connected to TIM15 IC1 and TIM15 IC2 respectively
2: MapTim3Tim15: TIM3 IC1 and TIM3 IC2 are connected to TIM15 IC1 and TIM15 IC2 respectively
3: MapTim4Tim15: TIM4 IC1 and TIM4 IC2 are connected to TIM15 IC1 and TIM15 IC2 respectively (STM32F303xB/C and STM32F358xC devices only)

I2C3_FMP

Bit 24: I2C3 Fast Mode Plus.

Allowed values:
0: Standard: FM+ mode is controlled by I2C_Pxx_FMP bits only
1: FMP: FM+ mode is enabled on all I2C3 pins selected through selection through IOPORT control registers AF selection bits

FPU_IE0

Bit 26: Invalid operation interrupt enable.

Allowed values:
0: Disabled: Invalid operation interrupt disable
1: Enabled: Invalid operation interrupt enable

FPU_IE1

Bit 27: Devide-by-zero interrupt enable.

Allowed values:
0: Disabled: Devide-by-zero interrupt disable
1: Enabled: Devide-by-zero interrupt enable

FPU_IE2

Bit 28: Underflow interrupt enable.

Allowed values:
0: Disabled: Underflow interrupt disable
1: Enabled: Underflow interrupt enable

FPU_IE3

Bit 29: Overflow interrupt enable.

Allowed values:
0: Disabled: Overflow interrupt disable
1: Enabled: Overflow interrupt enable

FPU_IE4

Bit 30: Input denormal interrupt enable.

Allowed values:
0: Disabled: Input denormal interrupt disable
1: Enabled: Input denormal interrupt enable

FPU_IE5

Bit 31: Inexact interrupt enable.

Allowed values:
0: Disabled: Inexact interrupt disable
1: Enabled: Inexact interrupt enable

RCR

CCM SRAM protection register

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PAGE15_WP rw	PAGE14_WP rw	PAGE13_WP rw	PAGE12_WP rw	PAGE11_WP rw	PAGE10_WP rw	PAGE9_WP rw	PAGE8_WP rw	PAGE7_WP rw	PAGE6_WP rw	PAGE5_WP rw	PAGE4_WP rw	PAGE3_WP rw	PAGE2_WP rw	PAGE1_WP rw	PAGE0_WP rw

Toggle fields

PAGE0_WP

Bit 0: CCM SRAM page write protection bit.

Allowed values:
0: Disabled: Write protection of pagex is disabled
1: Enabled: Write protection of pagex is enabled

PAGE1_WP

Bit 1: CCM SRAM page write protection bit.

Allowed values:
0: Disabled: Write protection of pagex is disabled
1: Enabled: Write protection of pagex is enabled

PAGE2_WP

Bit 2: CCM SRAM page write protection bit.

Allowed values:
0: Disabled: Write protection of pagex is disabled
1: Enabled: Write protection of pagex is enabled

PAGE3_WP

Bit 3: CCM SRAM page write protection bit.

Allowed values:
0: Disabled: Write protection of pagex is disabled
1: Enabled: Write protection of pagex is enabled

PAGE4_WP

Bit 4: CCM SRAM page write protection bit.

Allowed values:
0: Disabled: Write protection of pagex is disabled
1: Enabled: Write protection of pagex is enabled

PAGE5_WP

Bit 5: CCM SRAM page write protection bit.

Allowed values:
0: Disabled: Write protection of pagex is disabled
1: Enabled: Write protection of pagex is enabled

PAGE6_WP

Bit 6: CCM SRAM page write protection bit.

Allowed values:
0: Disabled: Write protection of pagex is disabled
1: Enabled: Write protection of pagex is enabled

PAGE7_WP

Bit 7: CCM SRAM page write protection bit.

Allowed values:
0: Disabled: Write protection of pagex is disabled
1: Enabled: Write protection of pagex is enabled

PAGE8_WP

Bit 8: CCM SRAM page write protection bit.

Allowed values:
0: Disabled: Write protection of pagex is disabled
1: Enabled: Write protection of pagex is enabled

PAGE9_WP

Bit 9: CCM SRAM page write protection bit.

Allowed values:
0: Disabled: Write protection of pagex is disabled
1: Enabled: Write protection of pagex is enabled

PAGE10_WP

Bit 10: CCM SRAM page write protection bit.

Allowed values:
0: Disabled: Write protection of pagex is disabled
1: Enabled: Write protection of pagex is enabled

PAGE11_WP

Bit 11: CCM SRAM page write protection bit.

Allowed values:
0: Disabled: Write protection of pagex is disabled
1: Enabled: Write protection of pagex is enabled

PAGE12_WP

Bit 12: CCM SRAM page write protection bit.

Allowed values:
0: Disabled: Write protection of pagex is disabled
1: Enabled: Write protection of pagex is enabled

PAGE13_WP

Bit 13: CCM SRAM page write protection bit.

Allowed values:
0: Disabled: Write protection of pagex is disabled
1: Enabled: Write protection of pagex is enabled

PAGE14_WP

Bit 14: CCM SRAM page write protection bit.

Allowed values:
0: Disabled: Write protection of pagex is disabled
1: Enabled: Write protection of pagex is enabled

PAGE15_WP

Bit 15: CCM SRAM page write protection bit.

Allowed values:
0: Disabled: Write protection of pagex is disabled
1: Enabled: Write protection of pagex is enabled

EXTICR1

external interrupt configuration register 1

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

4/4 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
EXTI3 rw				EXTI2 rw				EXTI1 rw				EXTI0 rw

Toggle fields

EXTI0

Bits 0-3: EXTI 0 configuration bits.

Allowed values:
0: PA0: Select PA0 as the source input for the EXTI0 external interrupt
1: PB0: Select PB0 as the source input for the EXTI0 external interrupt
2: PC0: Select PC0 as the source input for the EXTI0 external interrupt
3: PD0: Select PD0 as the source input for the EXTI0 external interrupt
4: PE0: Select PE0 as the source input for the EXTI0 external interrupt
5: PF0: Select PF0 as the source input for the EXTI0 external interrupt
6: PG0: Select PG0 as the source input for the EXTI0 external interrupt
7: PH0: Select PH0 as the source input for the EXTI0 external interrupt

EXTI1

Bits 4-7: EXTI 1 configuration bits.

Allowed values:
0: PA1: Select PA1 as the source input for the EXTI1 external interrupt
1: PB1: Select PB1 as the source input for the EXTI1 external interrupt
2: PC1: Select PC1 as the source input for the EXTI1 external interrupt
3: PD1: Select PD1 as the source input for the EXTI1 external interrupt
4: PE1: Select PE1 as the source input for the EXTI1 external interrupt
5: PF1: Select PF1 as the source input for the EXTI1 external interrupt
6: PG1: Select PG1 as the source input for the EXTI1 external interrupt
7: PH1: Select PH1 as the source input for the EXTI1 external interrupt

EXTI2

Bits 8-11: EXTI 2 configuration bits.

Allowed values:
0: PA2: Select PA2 as the source input for the EXTI2 external interrupt
1: PB2: Select PB2 as the source input for the EXTI2 external interrupt
2: PC2: Select PC2 as the source input for the EXTI2 external interrupt
3: PD2: Select PD2 as the source input for the EXTI2 external interrupt
4: PE2: Select PE2 as the source input for the EXTI2 external interrupt
5: PF2: Select PF2 as the source input for the EXTI2 external interrupt
6: PG2: Select PG2 as the source input for the EXTI2 external interrupt
7: PH2: Select PH2 as the source input for the EXTI2 external interrupt

EXTI3

Bits 12-15: EXTI 3 configuration bits.

Allowed values:
0: PA3: Select PA3 as the source input for the EXTI3 external interrupt
1: PB3: Select PB3 as the source input for the EXTI3 external interrupt
2: PC3: Select PC3 as the source input for the EXTI3 external interrupt
3: PD3: Select PD3 as the source input for the EXTI3 external interrupt
4: PE3: Select PE3 as the source input for the EXTI3 external interrupt
5: PF3: Select PF3 as the source input for the EXTI3 external interrupt
6: PG3: Select PG3 as the source input for the EXTI3 external interrupt

EXTICR2

external interrupt configuration register 2

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

4/4 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
EXTI7 rw				EXTI6 rw				EXTI5 rw				EXTI4 rw

Toggle fields

EXTI4

Bits 0-3: EXTI 4 configuration bits.

Allowed values:
0: PA4: Select PA4 as the source input for the EXTI4 external interrupt
1: PB4: Select PB4 as the source input for the EXTI4 external interrupt
2: PC4: Select PC4 as the source input for the EXTI4 external interrupt
3: PD4: Select PD4 as the source input for the EXTI4 external interrupt
4: PE4: Select PE4 as the source input for the EXTI4 external interrupt
5: PF4: Select PF4 as the source input for the EXTI4 external interrupt
6: PG4: Select PG4 as the source input for the EXTI4 external interrupt

EXTI5

Bits 4-7: EXTI 5 configuration bits.

Allowed values:
0: PA5: Select PA5 as the source input for the EXTI5 external interrupt
1: PB5: Select PB5 as the source input for the EXTI5 external interrupt
2: PC5: Select PC5 as the source input for the EXTI5 external interrupt
3: PD5: Select PD5 as the source input for the EXTI5 external interrupt
4: PE5: Select PE5 as the source input for the EXTI5 external interrupt
5: PF5: Select PF5 as the source input for the EXTI5 external interrupt
6: PG5: Select PG5 as the source input for the EXTI5 external interrupt

EXTI6

Bits 8-11: EXTI 6 configuration bits.

Allowed values:
0: PA6: Select PA6 as the source input for the EXTI6 external interrupt
1: PB6: Select PB6 as the source input for the EXTI6 external interrupt
2: PC6: Select PC6 as the source input for the EXTI6 external interrupt
3: PD6: Select PD6 as the source input for the EXTI6 external interrupt
4: PE6: Select PE6 as the source input for the EXTI6 external interrupt
5: PF6: Select PF6 as the source input for the EXTI6 external interrupt
6: PG6: Select PG6 as the source input for the EXTI6 external interrupt

EXTI7

Bits 12-15: EXTI 7 configuration bits.

Allowed values:
0: PA7: Select PA7 as the source input for the EXTI7 external interrupt
1: PB7: Select PB7 as the source input for the EXTI7 external interrupt
2: PC7: Select PC7 as the source input for the EXTI7 external interrupt
3: PD7: Select PD7 as the source input for the EXTI7 external interrupt
4: PE7: Select PE7 as the source input for the EXTI7 external interrupt
5: PF7: Select PF7 as the source input for the EXTI7 external interrupt
6: PG7: Select PG7 as the source input for the EXTI7 external interrupt

EXTICR3

external interrupt configuration register 3

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

4/4 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
EXTI11 rw				EXTI10 rw				EXTI9 rw				EXTI8 rw

Toggle fields

EXTI8

Bits 0-3: EXTI 8 configuration bits.

Allowed values:
0: PA8: Select PA8 as the source input for the EXTI8 external interrupt
1: PB8: Select PB8 as the source input for the EXTI8 external interrupt
2: PC8: Select PC8 as the source input for the EXTI8 external interrupt
3: PD8: Select PD8 as the source input for the EXTI8 external interrupt
4: PE8: Select PE8 as the source input for the EXTI8 external interrupt
5: PF8: Select PF8 as the source input for the EXTI8 external interrupt
6: PG8: Select PG8 as the source input for the EXTI8 external interrupt

EXTI9

Bits 4-7: EXTI 9 configuration bits.

Allowed values:
0: PA9: Select PA9 as the source input for the EXTI9 external interrupt
1: PB9: Select PB9 as the source input for the EXTI9 external interrupt
2: PC9: Select PC9 as the source input for the EXTI9 external interrupt
3: PD9: Select PD9 as the source input for the EXTI9 external interrupt
4: PE9: Select PE9 as the source input for the EXTI9 external interrupt
5: PF9: Select PF9 as the source input for the EXTI9 external interrupt
6: PG9: Select PG9 as the source input for the EXTI9 external interrupt

EXTI10

Bits 8-11: EXTI 10 configuration bits.

Allowed values:
0: PA10: Select PA10 as the source input for the EXTI10 external interrupt
1: PB10: Select PB10 as the source input for the EXTI10 external interrupt
2: PC10: Select PC10 as the source input for the EXTI10 external interrupt
3: PD10: Select PD10 as the source input for the EXTI10 external interrupt
4: PE10: Select PE10 as the source input for the EXTI10 external interrupt
5: PF10: Select PF10 as the source input for the EXTI10 external interrupt
6: PG10: Select PG10 as the source input for the EXTI10 external interrupt

EXTI11

Bits 12-15: EXTI 11 configuration bits.

Allowed values:
0: PA11: Select PA11 as the source input for the EXTI11 external interrupt
1: PB11: Select PB11 as the source input for the EXTI11 external interrupt
2: PC11: Select PC11 as the source input for the EXTI11 external interrupt
3: PD11: Select PD11 as the source input for the EXTI11 external interrupt
4: PE11: Select PE11 as the source input for the EXTI11 external interrupt
5: PF11: Select PF11 as the source input for the EXTI11 external interrupt
6: PG11: Select PG11 as the source input for the EXTI11 external interrupt

EXTICR4

external interrupt configuration register 4

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

4/4 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
EXTI15 rw				EXTI14 rw				EXTI13 rw				EXTI12 rw

Toggle fields

EXTI12

Bits 0-3: EXTI 12 configuration bits.

Allowed values:
0: PA12: Select PA12 as the source input for the EXTI12 external interrupt
1: PB12: Select PB12 as the source input for the EXTI12 external interrupt
2: PC12: Select PC12 as the source input for the EXTI12 external interrupt
3: PD12: Select PD12 as the source input for the EXTI12 external interrupt
4: PE12: Select PE12 as the source input for the EXTI12 external interrupt
5: PF12: Select PF12 as the source input for the EXTI12 external interrupt
6: PG12: Select PG12 as the source input for the EXTI12 external interrupt

EXTI13

Bits 4-7: EXTI 13 configuration bits.

Allowed values:
0: PA13: Select PA13 as the source input for the EXTI13 external interrupt
1: PB13: Select PB13 as the source input for the EXTI13 external interrupt
2: PC13: Select PC13 as the source input for the EXTI13 external interrupt
3: PD13: Select PD13 as the source input for the EXTI13 external interrupt
4: PE13: Select PE13 as the source input for the EXTI13 external interrupt
5: PF13: Select PF13 as the source input for the EXTI13 external interrupt
6: PG13: Select PG13 as the source input for the EXTI13 external interrupt

EXTI14

Bits 8-11: EXTI 14 configuration bits.

Allowed values:
0: PA14: Select PA14 as the source input for the EXTI14 external interrupt
1: PB14: Select PB14 as the source input for the EXTI14 external interrupt
2: PC14: Select PC14 as the source input for the EXTI14 external interrupt
3: PD14: Select PD14 as the source input for the EXTI14 external interrupt
4: PE14: Select PE14 as the source input for the EXTI14 external interrupt
5: PF14: Select PF14 as the source input for the EXTI14 external interrupt
6: PG14: Select PG14 as the source input for the EXTI14 external interrupt

EXTI15

Bits 12-15: EXTI 15 configuration bits.

Allowed values:
0: PA15: Select PA15 as the source input for the EXTI15 external interrupt
1: PB15: Select PB15 as the source input for the EXTI15 external interrupt
2: PC15: Select PC15 as the source input for the EXTI15 external interrupt
3: PD15: Select PD15 as the source input for the EXTI15 external interrupt
4: PE15: Select PE15 as the source input for the EXTI15 external interrupt
5: PF15: Select PF15 as the source input for the EXTI15 external interrupt
6: PG15: Select PG15 as the source input for the EXTI15 external interrupt

CFGR2

configuration register 2

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

5/5 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							SRAM_PEF rw				BYP_ADDR_PAR rw		PVD_LOCK rw	SRAM_PARITY_LOCK rw	LOCKUP_LOCK rw

Toggle fields

LOCKUP_LOCK

Bit 0: Cortex-M0 LOCKUP bit enable bit.

Allowed values:
0: Disconnected: Cortex-M4F LOCKUP output disconnected from TIM1/15/16/17 Break input
1: Connected: Cortex-M4F LOCKUP output connected to TIM1/15/16/17 Break input

SRAM_PARITY_LOCK

Bit 1: SRAM parity lock bit.

Allowed values:
0: Disconnected: SRAM parity error disconnected from TIM1/15/16/17 Break input
1: Connected: SRAM parity error connected to TIM1/15/16/17 Break input

PVD_LOCK

Bit 2: PVD lock enable bit.

Allowed values:
0: Disconnected: PVD interrupt disconnected from TIM15/16/17 Break input
1: Connected: PVD interrupt connected to TIM15/16/17 Break input

BYP_ADDR_PAR

Bit 4: Bypass address bit 29 in parity calculation.

Allowed values:
0: NoBypass: The ramload operation is performed taking into consideration bit 29 of the address when the parity is calculated
1: Bypass: The ramload operation is performed without taking into consideration bit 29 of the address when the parity is calculated

SRAM_PEF

Bit 8: SRAM parity flag.

Allowed values:
0: NoParityError: No SRAM parity error detected
1: ParityErrorDetected: SRAM parity error detected

CFGR4

configuration register 4

Offset: 0x48, size: 32, reset: 0x00000000, access: read-write

14/14 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		ADC34_JEXT14_RMP rw	ADC34_JEXT11_RMP rw	ADC34_JEXT5_RMP rw	ADC34_EXT15_RMP rw	ADC34_EXT6_RMP rw	ADC34_EXT5_RMP rw	ADC12_JEXT13_RMP rw	ADC12_JEXT6_RMP rw	ADC12_JEXT3_RMP rw	ADC12_EXT15_RMP rw	ADC12_EXT13_RMP rw	ADC12_EXT5_RMP rw	ADC12_EXT3_RMP rw	ADC12_EXT2_RMP rw

Toggle fields

ADC12_EXT2_RMP

Bit 0: Controls the Input trigger of ADC12 regular channel EXT2.

Allowed values:
0: Tim1: Trigger source is TIM3_CC3
1: Tim20: rigger source is TIM20_TRGO

ADC12_EXT3_RMP

Bit 1: Controls the Input trigger of ADC12 regular channel EXT3.

Allowed values:
0: Tim2: Trigger source is TIM2_CC2
1: Tim20: rigger source is TIM20_TRGO2

ADC12_EXT5_RMP

Bit 2: Controls the Input trigger of ADC12 regular channel EXT5.

Allowed values:
0: Tim4: Trigger source is TIM4_CC4
1: Tim20: Trigger source is TIM20_CC1

ADC12_EXT13_RMP

Bit 3: Controls the Input trigger of ADC12 regular channel EXT13.

Allowed values:
0: Tim6: Trigger source is TIM6_TRGO
1: Tim20: Trigger source is TIM20_CC2

ADC12_EXT15_RMP

Bit 4: Controls the Input trigger of ADC12 regular channel EXT15.

Allowed values:
0: Tim3: Trigger source is TIM3_CC4
1: Tim20: Trigger source is TIM20_CC3

ADC12_JEXT3_RMP

Bit 5: Controls the Input trigger of ADC12 injected channel JEXT3.

Allowed values:
0: Tim2: Trigger source is TIM2_CC1
1: Tim20: Trigger source is TIM20_TRGO

ADC12_JEXT6_RMP

Bit 6: Controls the Input trigger of ADC12 injected channel JEXT6.

Allowed values:
0: Exti15: Trigger source is EXTI line 15
1: Tim20: Trigger source is TIM20_TRGO2

ADC12_JEXT13_RMP

Bit 7: Controls the Input trigger of ADC12 injected channel JEXT13.

Allowed values:
0: Tim3: Trigger source is TIM3_CC1
1: Tim20: Trigger source is TIM20_CC4

ADC34_EXT5_RMP

Bit 8: Controls the Input trigger of ADC34 regular channel EXT5.

Allowed values:
0: Exti2: Trigger source is EXTI line 2 when reset at 0
1: Tim20: Trigger source is TIM20_TRGO

ADC34_EXT6_RMP

Bit 9: Controls the Input trigger of ADC34 regular channel EXT6.

Allowed values:
0: Tim4: Trigger source is TIM4_CC1
1: Tim20: Trigger source is TIM20_TRGO2

ADC34_EXT15_RMP

Bit 10: Controls the Input trigger of ADC34 regular channel EXT15.

Allowed values:
0: Tim2: Trigger source is TIM2_CC1
1: Tim20: Trigger source is TIM20_CC1

ADC34_JEXT5_RMP

Bit 11: Controls the Input trigger of ADC34 injected channel JEXT5.

Allowed values:
0: Tim4: Trigger source is TIM4_CC3
1: Tim20: Trigger source is TIM20_TRGO

ADC34_JEXT11_RMP

Bit 12: Controls the Input trigger of ADC34 injected channel JEXT11.

Allowed values:
0: Tim1: Trigger source is TIM1_CC3
1: Tim20: Trigger source is TIM20_TRGO2

ADC34_JEXT14_RMP

Bit 13: Controls the Input trigger of ADC34 injected channel JEXT14.

Allowed values:
0: Tim7: Trigger source is TIM7_TRGO
1: Tim20: Trigger source is TIM20_CC2

CFGR3

configuration register 3

Offset: 0x50, size: 32, reset: 0x00000200, access: read-write

5/5 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						ADC2_DMA_RMP rw		I2C1_TX_DMA_RMP rw		I2C1_RX_DMA_RMP rw		SPI1_TX_DMA_RMP rw		SPI1_RX_DMA_RMP rw

Toggle fields

SPI1_RX_DMA_RMP

Bits 0-1: SPI1_RX DMA remapping bit.

Allowed values:
0: MapDma1Ch3: SPI1_RX mapped on DMA1 CH2
1: MapDma1Ch5: SPI1_RX mapped on DMA1 CH4
2: MapDma1Ch7: SPI1_RX mapped on DMA1 CH6

SPI1_TX_DMA_RMP

Bits 2-3: SPI1_TX DMA remapping bit.

Allowed values:
0: MapDma1Ch3: SPI1_TX mapped on DMA1 CH3
1: MapDma1Ch5: SPI1_TX mapped on DMA1 CH5
2: MapDma1Ch7: SPI1_TX mapped on DMA1 CH7

I2C1_RX_DMA_RMP

Bits 4-5: I2C1_RX DMA remapping bit.

Allowed values:
0: MapDma1Ch7: I2C1_RX mapped on DMA1 CH7
1: MapDma1Ch3: I2C1_RX mapped on DMA1 CH3
2: MapDma1Ch5: I2C1_RX mapped on DMA1 CH5

I2C1_TX_DMA_RMP

Bits 6-7: I2C1_TX DMA remapping bit.

Allowed values:
0: MapDma1Ch6: I2C1_TX mapped on DMA1 CH6
1: MapDma1Ch2: I2C1_TX mapped on DMA1 CH2
2: MapDma1Ch4: I2C1_TX mapped on DMA1 CH4

ADC2_DMA_RMP

Bits 8-9: ADC2 DMA remapping bit.

Allowed values:
0: MapDma2: ADC2 mapped on DMA2
2: MapDma1Ch2: ADC2 mapped on DMA1 channel 2
3: MapDma1Ch4: ADC2 mapped on DMA1 channel 4

TIM1

0x40012c00: Advanced timer

107/168 fields covered.

Toggle register map

Offset	Name	31	30	29	25	24	23	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	CR1																	UIFREMAP		CKD		ARPE	CMS		DIR	OPM	URS	UDIS	CEN
0x4	CR2						MMS2				OIS[6]		OIS[5]		OIS[4]	OIS[3]N	OIS[3]	OIS[2]N	OIS[2]	OIS[1]N	OIS[1]	TI1S	MMS			CCDS	CCUS		CCPC
0x8	SMCR												SMS3	ETP	ECE	ETPS		ETF				MSM	TS			OCCS	SMS
0xc	DIER														TDE	COMDE	CC[4]DE	CC[3]DE	CC[2]DE	CC[1]DE	UDE	BIE	TIE	COMIE	CC[4]IE	CC[3]IE	CC[2]IE	CC[1]IE	UIE
0x10	SR											C6IF	C5IF				CC[4]OF	CC[3]OF	CC[2]OF	CC[1]OF	B2IF	BIF	TIF	COMIF	CC[4]IF	CC[3]IF	CC[2]IF	CC[1]IF	UIF
0x14	EGR																				B2G	BG	TG	COMG	CC[4]G	CC[3]G	CC[2]G	CC[1]G	UG
0x18	CCMR1_Input													IC[2]F				IC[2]PSC		CC[2]S		IC[1]F				IC[1]PSC		CC[1]S
0x18	CCMR1_Output					OC[2]M_3							OC[1]M_3	OC[2]CE	OC[2]M			OC[2]PE	OC[2]FE	CC[2]S		OC[1]CE	OC[1]M			OC[1]PE	OC[1]FE	CC[1]S
0x1c	CCMR2_Input													IC[4]F				IC[4]PSC		CC[4]S		IC[3]F				IC[3]PSC		CC[3]S
0x1c	CCMR2_Output					OC[4]M_3							OC[3]M_3	OC[4]CE	OC[4]M			OC[4]PE	OC[4]FE	CC[4]S		OC[3]CE	OC[3]M			OC[3]PE	OC[3]FE	CC[3]S
0x20	CCER							CC[6]P	CC[6]E			CC[5]P	CC[5]E	CC[4]NP		CC[4]P	CC[4]E	CC[3]NP	CC[3]NE	CC[3]P	CC[3]E	CC[2]NP	CC[2]NE	CC[2]P	CC[2]E	CC[1]NP	CC[1]NE	CC[1]P	CC[1]E
0x24	CNT	UIFCPY												CNT
0x28	PSC													PSC
0x2c	ARR													ARR
0x30	RCR													REP
0x34	CCR[1]													CCR
0x38	CCR[2]													CCR
0x3c	CCR[3]													CCR
0x40	CCR[4]													CCR
0x44	BDTR				BK2P	BK2E	BK2F			BKF				MOE	AOE	BKP	BKE	OSSR	OSSI	LOCK		DTG
0x48	DCR																DBL								DBA
0x4c	DMAR													DMAB
0x54	CCMR3_Output					OC[6]M_3							OC[5]M_3	OC[6]CE	OC[6]M			OC[6]PE	OC[6]FE			OC[5]CE	OC[5]M			OC[5]PE	OC[5]FE
0x58	CCR5	GC5C3	GC5C2	GC5C1										CCR
0x5c	CCR6													CCR
0x60	OR																									TIM1_ETR_ADC4_RMP		TIM1_ETR_ADC1_RMP

Toggle registers

CR1

control register 1

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

8/9 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				UIFREMAP rw		CKD rw		ARPE rw	CMS rw		DIR rw	OPM rw	URS rw	UDIS rw	CEN rw

Toggle fields

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

Allowed values:
0: AnyEvent: Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request
1: CounterOnly: Only counter overflow/underflow generates an update interrupt or DMA request

OPM

Bit 3: One-pulse mode.

Allowed values:
0: Disabled: Counter is not stopped at update event
1: Enabled: Counter stops counting at the next update event (clearing the CEN bit)

DIR

Bit 4: Direction.

Allowed values:
0: Up: Counter used as upcounter
1: Down: Counter used as downcounter

CMS

Bits 5-6: Center-aligned mode selection.

Allowed values:
0: EdgeAligned: The counter counts up or down depending on the direction bit
1: CenterAligned1: The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting down.
2: CenterAligned2: The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting up.
3: CenterAligned3: The counter counts up and down alternatively. Output compare interrupt flags are set both when the counter is counting up or down.

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CKD

Bits 8-9: Clock division.

Allowed values:
0: Div1: t_DTS = t_CK_INT
1: Div2: t_DTS = 2 × t_CK_INT
2: Div4: t_DTS = 4 × t_CK_INT

UIFREMAP

Bit 11: UIF status bit remapping.

CR2

control register 2

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

12/15 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								MMS2 rw					OIS[6] rw		OIS[5] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	OIS[4] rw	OIS[3]N rw	OIS[3] rw	OIS[2]N rw	OIS[2] rw	OIS[1]N rw	OIS[1] rw	TI1S rw	MMS rw			CCDS rw	CCUS rw		CCPC rw

Toggle fields

CCPC

Bit 0: Capture/compare preloaded control.

CCUS

Bit 2: Capture/compare control update selection.

CCDS

Bit 3: Capture/compare DMA selection.

Allowed values:
0: OnCompare: CCx DMA request sent when CCx event occurs
1: OnUpdate: CCx DMA request sent when update event occurs

MMS

Bits 4-6: Master mode selection.

Allowed values:
0: Reset: The UG bit from the TIMx_EGR register is used as trigger output
1: Enable: The counter enable signal, CNT_EN, is used as trigger output
2: Update: The update event is selected as trigger output
3: ComparePulse: The trigger output send a positive pulse when the CC1IF flag it to be set, as soon as a capture or a compare match occurred
4: CompareOC1: OC1REF signal is used as trigger output
5: CompareOC2: OC2REF signal is used as trigger output
6: CompareOC3: OC3REF signal is used as trigger output
7: CompareOC4: OC4REF signal is used as trigger output

TI1S

Bit 7: TI1 selection.

Allowed values:
0: Normal: The TIMx_CH1 pin is connected to TI1 input
1: XOR: The TIMx_CH1, CH2, CH3 pins are connected to TI1 input

OIS[1]

Bit 8: Output Idle state (OC1 output).

Allowed values:
0: Reset: OCx=0 (after a dead-time if OCx(N) is implemented) when MOE=0
1: Set: OCx=1 (after a dead-time if OCx(N) is implemented) when MOE=0

OIS[1]N

Bit 9: Output Idle state (OC1N output).

Allowed values:
0: Reset: OCxN=0 after a dead-time when MOE=0
1: Set: OCxN=1 after a dead-time when MOE=0

OIS[2]

Bit 10: Output Idle state (OC2 output).

Allowed values:
0: Reset: OCx=0 (after a dead-time if OCx(N) is implemented) when MOE=0
1: Set: OCx=1 (after a dead-time if OCx(N) is implemented) when MOE=0

OIS[2]N

Bit 11: Output Idle state (OC2N output).

Allowed values:
0: Reset: OCxN=0 after a dead-time when MOE=0
1: Set: OCxN=1 after a dead-time when MOE=0

OIS[3]

Bit 12: Output Idle state (OC3 output).

Allowed values:
0: Reset: OCx=0 (after a dead-time if OCx(N) is implemented) when MOE=0
1: Set: OCx=1 (after a dead-time if OCx(N) is implemented) when MOE=0

OIS[3]N

Bit 13: Output Idle state (OC3N output).

Allowed values:
0: Reset: OCxN=0 after a dead-time when MOE=0
1: Set: OCxN=1 after a dead-time when MOE=0

OIS[4]

Bit 14: Output Idle state (OC4 output).

Allowed values:
0: Reset: OCx=0 (after a dead-time if OCx(N) is implemented) when MOE=0
1: Set: OCx=1 (after a dead-time if OCx(N) is implemented) when MOE=0

OIS[5]

Bit 16: Output Idle state (OC5 output).

Allowed values:
0: Reset: OCx=0 (after a dead-time if OCx(N) is implemented) when MOE=0
1: Set: OCx=1 (after a dead-time if OCx(N) is implemented) when MOE=0

OIS[6]

Bit 18: Output Idle state (OC6 output).

Allowed values:
0: Reset: OCx=0 (after a dead-time if OCx(N) is implemented) when MOE=0
1: Set: OCx=1 (after a dead-time if OCx(N) is implemented) when MOE=0

MMS2

Bits 20-23: Master mode selection 2.

SMCR

slave mode control register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

7/9 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															SMS3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ETP rw	ECE rw	ETPS rw		ETF rw				MSM rw	TS rw			OCCS rw	SMS rw

Toggle fields

SMS

Bits 0-2: Slave mode selection.

Allowed values:
0: Disabled: Slave mode disabled - if CEN = ‘1 then the prescaler is clocked directly by the internal clock.
1: Encoder_Mode_1: Encoder mode 1 - Counter counts up/down on TI2FP1 edge depending on TI1FP2 level.
2: Encoder_Mode_2: Encoder mode 2 - Counter counts up/down on TI1FP2 edge depending on TI2FP1 level.
3: Encoder_Mode_3: Encoder mode 3 - Counter counts up/down on both TI1FP1 and TI2FP2 edges depending on the level of the other input.
4: Reset_Mode: Reset Mode - Rising edge of the selected trigger input (TRGI) reinitializes the counter and generates an update of the registers.
5: Gated_Mode: Gated Mode - The counter clock is enabled when the trigger input (TRGI) is high. The counter stops (but is not reset) as soon as the trigger becomes low. Both start and stop of the counter are controlled.
6: Trigger_Mode: Trigger Mode - The counter starts at a rising edge of the trigger TRGI (but it is not reset). Only the start of the counter is controlled.
7: Ext_Clock_Mode: External Clock Mode 1 - Rising edges of the selected trigger (TRGI) clock the counter.

OCCS

Bit 3: OCREF clear selection.

TS

Bits 4-6: Trigger selection.

Allowed values:
0: ITR0: Internal Trigger 0 (ITR0)
1: ITR1: Internal Trigger 1 (ITR1)
2: ITR2: Internal Trigger 2 (ITR2)
4: TI1F_ED: TI1 Edge Detector (TI1F_ED)
5: TI1FP1: Filtered Timer Input 1 (TI1FP1)
6: TI2FP2: Filtered Timer Input 2 (TI2FP2)
7: ETRF: External Trigger input (ETRF)

MSM

Bit 7: Master/Slave mode.

Allowed values:
0: NoSync: No action
1: Sync: The effect of an event on the trigger input (TRGI) is delayed to allow a perfect synchronization between the current timer and its slaves (through TRGO). It is useful if we want to synchronize several timers on a single external event.

ETF

Bits 8-11: External trigger filter.

Allowed values:
0: NoFilter: No filter, sampling is done at fDTS
1: FCK_INT_N2: fSAMPLING=fCK_INT, N=2
2: FCK_INT_N4: fSAMPLING=fCK_INT, N=4
3: FCK_INT_N8: fSAMPLING=fCK_INT, N=8
4: FDTS_Div2_N6: fSAMPLING=fDTS/2, N=6
5: FDTS_Div2_N8: fSAMPLING=fDTS/2, N=8
6: FDTS_Div4_N6: fSAMPLING=fDTS/4, N=6
7: FDTS_Div4_N8: fSAMPLING=fDTS/4, N=8
8: FDTS_Div8_N6: fSAMPLING=fDTS/8, N=6
9: FDTS_Div8_N8: fSAMPLING=fDTS/8, N=8
10: FDTS_Div16_N5: fSAMPLING=fDTS/16, N=5
11: FDTS_Div16_N6: fSAMPLING=fDTS/16, N=6
12: FDTS_Div16_N8: fSAMPLING=fDTS/16, N=8
13: FDTS_Div32_N5: fSAMPLING=fDTS/32, N=5
14: FDTS_Div32_N6: fSAMPLING=fDTS/32, N=6
15: FDTS_Div32_N8: fSAMPLING=fDTS/32, N=8

ETPS

Bits 12-13: External trigger prescaler.

Allowed values:
0: Div1: Prescaler OFF
1: Div2: ETRP frequency divided by 2
2: Div4: ETRP frequency divided by 4
3: Div8: ETRP frequency divided by 8

ECE

Bit 14: External clock enable.

Allowed values:
0: Disabled: External clock mode 2 disabled
1: Enabled: External clock mode 2 enabled. The counter is clocked by any active edge on the ETRF signal.

ETP

Bit 15: External trigger polarity.

Allowed values:
0: NotInverted: ETR is noninverted, active at high level or rising edge
1: Inverted: ETR is inverted, active at low level or falling edge

SMS3

Bit 16: Slave mode selection bit 3.

DIER

DMA/Interrupt enable register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

12/15 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	TDE rw	COMDE rw	CC[4]DE rw	CC[3]DE rw	CC[2]DE rw	CC[1]DE rw	UDE rw	BIE rw	TIE rw	COMIE rw	CC[4]IE rw	CC[3]IE rw	CC[2]IE rw	CC[1]IE rw	UIE rw

Toggle fields

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

CC[1]IE

Bit 1: Capture/Compare 1 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC[2]IE

Bit 2: Capture/Compare 2 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC[3]IE

Bit 3: Capture/Compare 3 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC[4]IE

Bit 4: Capture/Compare 4 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

COMIE

Bit 5: COM interrupt enable.

TIE

Bit 6: Trigger interrupt enable.

Allowed values:
0: Disabled: Trigger interrupt disabled
1: Enabled: Trigger interrupt enabled

BIE

Bit 7: Break interrupt enable.

UDE

Bit 8: Update DMA request enable.

Allowed values:
0: Disabled: Update DMA request disabled
1: Enabled: Update DMA request enabled

CC[1]DE

Bit 9: Capture/Compare 1 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC[2]DE

Bit 10: Capture/Compare 2 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC[3]DE

Bit 11: Capture/Compare 3 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC[4]DE

Bit 12: Capture/Compare 4 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

COMDE

Bit 13: COM DMA request enable.

TDE

Bit 14: Trigger DMA request enable.

Allowed values:
0: Disabled: Trigger DMA request disabled
1: Enabled: Trigger DMA request enabled

SR

status register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

10/15 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
														C6IF rw	C5IF rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			CC[4]OF rw	CC[3]OF rw	CC[2]OF rw	CC[1]OF rw	B2IF rw	BIF rw	TIF rw	COMIF rw	CC[4]IF rw	CC[3]IF rw	CC[2]IF rw	CC[1]IF rw	UIF rw

Toggle fields

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: NoUpdateOccurred: No update occurred
1: UpdatePending: Update interrupt pending

CC[1]IF

Bit 1: Capture/compare 1 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC[2]IF

Bit 2: Capture/compare 2 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC[3]IF

Bit 3: Capture/compare 3 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC[4]IF

Bit 4: Capture/compare 4 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

COMIF

Bit 5: COM interrupt flag.

TIF

Bit 6: Trigger interrupt flag.

Allowed values:
0: NoTrigger: No trigger event occurred
1: Trigger: Trigger interrupt pending

BIF

Bit 7: Break interrupt flag.

B2IF

Bit 8: Break 2 interrupt flag.

CC[1]OF

Bit 9: Capture/Compare 1 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC[2]OF

Bit 10: Capture/Compare 2 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC[3]OF

Bit 11: Capture/Compare 3 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC[4]OF

Bit 12: Capture/Compare 4 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

C5IF

Bit 16: Capture/Compare 5 interrupt flag.

C6IF

Bit 17: Capture/Compare 6 interrupt flag.

EGR

event generation register

Offset: 0x14, size: 32, reset: 0x00000000, access: write-only

6/9 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							B2G w	BG w	TG w	COMG w	CC[4]G w	CC[3]G w	CC[2]G w	CC[1]G w	UG w

Toggle fields

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the registers.

CC[1]G

Bit 1: Capture/compare 1 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC[2]G

Bit 2: Capture/compare 2 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC[3]G

Bit 3: Capture/compare 3 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC[4]G

Bit 4: Capture/compare 4 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

COMG

Bit 5: Capture/Compare control update generation.

TG

Bit 6: Trigger generation.

Allowed values:
1: Trigger: The TIF flag is set in TIMx_SR register. Related interrupt or DMA transfer can occur if enabled.

BG

Bit 7: Break generation.

B2G

Bit 8: Break 2 generation.

CCMR1_Input

capture/compare mode register 1 (input mode)

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

4/6 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IC[2]F rw				IC[2]PSC rw		CC[2]S rw		IC[1]F rw				IC[1]PSC rw		CC[1]S rw

Toggle fields

CC[1]S

Bits 0-1: Capture/Compare 1 selection.

Allowed values:
1: TI1: CC1 channel is configured as input, IC1 is mapped on TI1
2: TI2: CC1 channel is configured as input, IC1 is mapped on TI2
3: TRC: CC1 channel is configured as input, IC1 is mapped on TRC

IC[1]PSC

Bits 2-3: Input capture 1 prescaler.

IC[1]F

Bits 4-7: Input capture 1 filter.

Allowed values:
0: NoFilter: No filter, sampling is done at fDTS
1: FCK_INT_N2: fSAMPLING=fCK_INT, N=2
2: FCK_INT_N4: fSAMPLING=fCK_INT, N=4
3: FCK_INT_N8: fSAMPLING=fCK_INT, N=8
4: FDTS_Div2_N6: fSAMPLING=fDTS/2, N=6
5: FDTS_Div2_N8: fSAMPLING=fDTS/2, N=8
6: FDTS_Div4_N6: fSAMPLING=fDTS/4, N=6
7: FDTS_Div4_N8: fSAMPLING=fDTS/4, N=8
8: FDTS_Div8_N6: fSAMPLING=fDTS/8, N=6
9: FDTS_Div8_N8: fSAMPLING=fDTS/8, N=8
10: FDTS_Div16_N5: fSAMPLING=fDTS/16, N=5
11: FDTS_Div16_N6: fSAMPLING=fDTS/16, N=6
12: FDTS_Div16_N8: fSAMPLING=fDTS/16, N=8
13: FDTS_Div32_N5: fSAMPLING=fDTS/32, N=5
14: FDTS_Div32_N6: fSAMPLING=fDTS/32, N=6
15: FDTS_Div32_N8: fSAMPLING=fDTS/32, N=8

CC[2]S

Bits 8-9: Capture/Compare 2 selection.

Allowed values:
1: TI1: CC1 channel is configured as input, IC1 is mapped on TI1
2: TI2: CC1 channel is configured as input, IC1 is mapped on TI2
3: TRC: CC1 channel is configured as input, IC1 is mapped on TRC

IC[2]PSC

Bits 10-11: Input capture 2 prescaler.

IC[2]F

Bits 12-15: Input capture 2 filter.

Allowed values:
0: NoFilter: No filter, sampling is done at fDTS
1: FCK_INT_N2: fSAMPLING=fCK_INT, N=2
2: FCK_INT_N4: fSAMPLING=fCK_INT, N=4
3: FCK_INT_N8: fSAMPLING=fCK_INT, N=8
4: FDTS_Div2_N6: fSAMPLING=fDTS/2, N=6
5: FDTS_Div2_N8: fSAMPLING=fDTS/2, N=8
6: FDTS_Div4_N6: fSAMPLING=fDTS/4, N=6
7: FDTS_Div4_N8: fSAMPLING=fDTS/4, N=8
8: FDTS_Div8_N6: fSAMPLING=fDTS/8, N=6
9: FDTS_Div8_N8: fSAMPLING=fDTS/8, N=8
10: FDTS_Div16_N5: fSAMPLING=fDTS/16, N=5
11: FDTS_Div16_N6: fSAMPLING=fDTS/16, N=6
12: FDTS_Div16_N8: fSAMPLING=fDTS/16, N=8
13: FDTS_Div32_N5: fSAMPLING=fDTS/32, N=5
14: FDTS_Div32_N6: fSAMPLING=fDTS/32, N=6
15: FDTS_Div32_N8: fSAMPLING=fDTS/32, N=8

CCMR1_Output

capture/compare mode register (output mode)

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

8/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
							OC[2]M_3 rw								OC[1]M_3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OC[2]CE rw	OC[2]M rw			OC[2]PE rw	OC[2]FE rw	CC[2]S rw		OC[1]CE rw	OC[1]M rw			OC[1]PE rw	OC[1]FE rw	CC[1]S rw

Toggle fields

CC[1]S

Bits 0-1: Capture/Compare 1 selection.

Allowed values:
0: Output: CC1 channel is configured as output

OC[1]FE

Bit 2: Output compare 1 fast enable.

OC[1]PE

Bit 3: Output compare 1 preload enable.

Allowed values:
0: Disabled: Preload register on CCR1 disabled. New values written to CCR1 are taken into account immediately
1: Enabled: Preload register on CCR1 enabled. Preload value is loaded into active register on each update event

OC[1]M

Bits 4-6: Output compare 1 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[1]CE

Bit 7: Output compare 1 clear enable.

CC[2]S

Bits 8-9: Capture/Compare 2 selection.

Allowed values:
0: Output: CC1 channel is configured as output

OC[2]FE

Bit 10: Output compare 2 fast enable.

OC[2]PE

Bit 11: Output compare 2 preload enable.

Allowed values:
0: Disabled: Preload register on CCR1 disabled. New values written to CCR1 are taken into account immediately
1: Enabled: Preload register on CCR1 enabled. Preload value is loaded into active register on each update event

OC[2]M

Bits 12-14: Output compare 2 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[2]CE

Bit 15: Output compare 2 clear enable.

OC[1]M_3

Bit 16: Output compare 1 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

OC[2]M_3

Bit 24: Output compare 2 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

CCMR2_Input

capture/compare mode register 2 (input mode)

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

6/6 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IC[4]F rw				IC[4]PSC rw		CC[4]S rw		IC[3]F rw				IC[3]PSC rw		CC[3]S rw

Toggle fields

CC[3]S

Bits 0-1: Capture/Compare 3 selection.

Allowed values:
1: TI3: CC3 channel is configured as input, IC3 is mapped on TI3
2: TI4: CC3 channel is configured as input, IC3 is mapped on TI4
3: TRC: CC3 channel is configured as input, IC3 is mapped on TRC

IC[3]PSC

Bits 2-3: Input capture 3 prescaler.

Allowed values: 0x0-0x3

IC[3]F

Bits 4-7: Input capture 3 filter.

Allowed values: 0x0-0xf

CC[4]S

Bits 8-9: Capture/Compare 4 selection.

Allowed values:
1: TI3: CC3 channel is configured as input, IC3 is mapped on TI3
2: TI4: CC3 channel is configured as input, IC3 is mapped on TI4
3: TRC: CC3 channel is configured as input, IC3 is mapped on TRC

IC[4]PSC

Bits 10-11: Input capture 4 prescaler.

Allowed values: 0x0-0x3

IC[4]F

Bits 12-15: Input capture 4 filter.

Allowed values: 0x0-0xf

CCMR2_Output

capture/compare mode register (output mode)

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

8/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
							OC[4]M_3 rw								OC[3]M_3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OC[4]CE rw	OC[4]M rw			OC[4]PE rw	OC[4]FE rw	CC[4]S rw		OC[3]CE rw	OC[3]M rw			OC[3]PE rw	OC[3]FE rw	CC[3]S rw

Toggle fields

CC[3]S

Bits 0-1: Capture/Compare 3 selection.

Allowed values:
0: Output: CC3 channel is configured as output

OC[3]FE

Bit 2: Output compare 3 fast enable.

OC[3]PE

Bit 3: Output compare 3 preload enable.

Allowed values:
0: Disabled: Preload register on CCR3 disabled. New values written to CCR3 are taken into account immediately
1: Enabled: Preload register on CCR3 enabled. Preload value is loaded into active register on each update event

OC[3]M

Bits 4-6: Output compare 3 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[3]CE

Bit 7: Output compare 3 clear enable.

CC[4]S

Bits 8-9: Capture/Compare 4 selection.

Allowed values:
0: Output: CC3 channel is configured as output

OC[4]FE

Bit 10: Output compare 4 fast enable.

OC[4]PE

Bit 11: Output compare 4 preload enable.

Allowed values:
0: Disabled: Preload register on CCR3 disabled. New values written to CCR3 are taken into account immediately
1: Enabled: Preload register on CCR3 enabled. Preload value is loaded into active register on each update event

OC[4]M

Bits 12-14: Output compare 4 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[4]CE

Bit 15: Output compare 4 clear enable.

OC[3]M_3

Bit 16: Output compare 3 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

OC[4]M_3

Bit 24: Output compare 4 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

CCER

capture/compare enable register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

0/19 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
										CC[6]P rw	CC[6]E rw			CC[5]P rw	CC[5]E rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CC[4]NP rw		CC[4]P rw	CC[4]E rw	CC[3]NP rw	CC[3]NE rw	CC[3]P rw	CC[3]E rw	CC[2]NP rw	CC[2]NE rw	CC[2]P rw	CC[2]E rw	CC[1]NP rw	CC[1]NE rw	CC[1]P rw	CC[1]E rw

Toggle fields

CC[1]E

Bit 0: Capture/Compare 1 output enable.

CC[1]P

Bit 1: Capture/Compare 1 output Polarity.

CC[1]NE

Bit 2: Capture/Compare 1 complementary output enable.

CC[1]NP

Bit 3: Capture/Compare 1 output Polarity.

CC[2]E

Bit 4: Capture/Compare 2 output enable.

CC[2]P

Bit 5: Capture/Compare 2 output Polarity.

CC[2]NE

Bit 6: Capture/Compare 2 complementary output enable.

CC[2]NP

Bit 7: Capture/Compare 2 output Polarity.

CC[3]E

Bit 8: Capture/Compare 3 output enable.

CC[3]P

Bit 9: Capture/Compare 3 output Polarity.

CC[3]NE

Bit 10: Capture/Compare 3 complementary output enable.

CC[3]NP

Bit 11: Capture/Compare 3 output Polarity.

CC[4]E

Bit 12: Capture/Compare 4 output enable.

CC[4]P

Bit 13: Capture/Compare 4 output Polarity.

CC[4]NP

Bit 15: Capture/Compare 4 output Polarity.

CC[5]E

Bit 16: Capture/Compare 5 output enable.

CC[5]P

Bit 17: Capture/Compare 5 output Polarity.

CC[6]E

Bit 20: Capture/Compare 6 output enable.

CC[6]P

Bit 21: Capture/Compare 6 output Polarity.

CNT

counter

Offset: 0x24, size: 32, reset: 0x00000000, access: Unspecified

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
UIFCPY r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CNT rw

Toggle fields

CNT

Bits 0-15: counter value.

Allowed values: 0x0-0xffff

UIFCPY

Bit 31: UIF copy.

PSC

prescaler

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PSC rw

Toggle fields

PSC

Bits 0-15: Prescaler value.

Allowed values: 0x0-0xffff

ARR

auto-reload register

Offset: 0x2c, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ARR rw

Toggle fields

ARR

Bits 0-15: Auto-reload value.

Allowed values: 0x0-0xffff

RCR

repetition counter register

Offset: 0x30, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
REP rw

Toggle fields

REP

Bits 0-15: Repetition counter value.

CCR[1]

capture/compare register

Offset: 0x34, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

Allowed values: 0x0-0xffff

CCR[2]

capture/compare register

Offset: 0x38, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

Allowed values: 0x0-0xffff

CCR[3]

capture/compare register

Offset: 0x3c, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

Allowed values: 0x0-0xffff

CCR[4]

capture/compare register

Offset: 0x40, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

Allowed values: 0x0-0xffff

BDTR

break and dead-time register

Offset: 0x44, size: 32, reset: 0x00000000, access: read-write

10/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
						BK2P rw	BK2E rw	BK2F rw				BKF rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MOE rw	AOE rw	BKP rw	BKE rw	OSSR rw	OSSI rw	LOCK rw		DTG rw

Toggle fields

DTG

Bits 0-7: Dead-time generator setup.

Allowed values: 0x0-0xff

LOCK

Bits 8-9: Lock configuration.

Allowed values:
0: Off: No bit is write protected
1: Level1: Any bits except MOE, OSSR, OSSI and LOCK in TIMx_BDTR register, OISx and OISxN bits in TIMx_CR2 register can no longer be written
2: Level2: LOCK Level 1 + CC Polarity bits (CCxP/CCxNP bits in TIMx_CCER register, as long as the related channel is configured in output through the CCxS bits) as well as OSSR and OSSI bits can no longer be written
3: Level3: LOCK Level 2 + CC Control bits (OCxM and OCxPE bits in TIMx_CCMRx registers, as long as the related channel is configured in output through the CCxS bits) can no longer be written

OSSI

Bit 10: Off-state selection for Idle mode.

Allowed values:
0: Disabled: When inactive, OC/OCN outputs are disabled
1: IdleLevel: When inactive, OC/OCN outputs are forced to idle level

OSSR

Bit 11: Off-state selection for Run mode.

Allowed values:
0: Disabled: When inactive, OC/OCN outputs are disabled
1: IdleLevel: When inactive, OC/OCN outputs are enabled with their inactive level

BKE

Bit 12: Break enable.

Allowed values:
0: Disabled: Break function x disabled
1: Enabled: Break function x disabled

BKP

Bit 13: Break polarity.

Allowed values:
0: ActiveLow: Break input BRKx is active low
1: ActiveHigh: Break input BRKx is active high

AOE

Bit 14: Automatic output enable.

Allowed values:
0: Manual: MOE can be set only by software
1: Automatic: MOE can be set by software or automatically at the next update event (if none of the break inputs BRK and BRK2 is active)

MOE

Bit 15: Main output enable.

Allowed values:
0: DisabledIdle: OC/OCN are disabled or forced idle depending on OSSI
1: Enabled: OC/OCN are enabled if CCxE/CCxNE are set

BKF

Bits 16-19: Break filter.

BK2F

Bits 20-23: Break 2 filter.

BK2E

Bit 24: Break 2 enable.

Allowed values:
0: Disabled: Break function x disabled
1: Enabled: Break function x disabled

BK2P

Bit 25: Break 2 polarity.

Allowed values:
0: ActiveLow: Break input BRKx is active low
1: ActiveHigh: Break input BRKx is active high

DCR

DMA control register

Offset: 0x48, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			DBL rw								DBA rw

Toggle fields

DBA

Bits 0-4: DMA base address.

Allowed values: 0x0-0x1f

DBL

Bits 8-12: DMA burst length.

Allowed values: 0x0-0x12

DMAR

DMA address for full transfer

Offset: 0x4c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DMAB rw

Toggle fields

DMAB

Bits 0-15: DMA register for burst accesses.

CCMR3_Output

capture/compare mode register 3 (output mode)

Offset: 0x54, size: 32, reset: 0x00000000, access: read-write

4/10 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
							OC[6]M_3 rw								OC[5]M_3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OC[6]CE rw	OC[6]M rw			OC[6]PE rw	OC[6]FE rw			OC[5]CE rw	OC[5]M rw			OC[5]PE rw	OC[5]FE rw

Toggle fields

OC[5]FE

Bit 2: Output compare 5 fast enable.

OC[5]PE

Bit 3: Output compare 5 preload enable.

OC[5]M

Bits 4-6: Output compare 5 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[5]CE

Bit 7: Output compare 5 clear enable.

OC[6]FE

Bit 10: Output compare 6 fast enable.

OC[6]PE

Bit 11: Output compare 6 preload enable.

OC[6]M

Bits 12-14: Output compare 6 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[6]CE

Bit 15: Output compare 6 clear enable.

OC[5]M_3

Bit 16: Output compare 5 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

OC[6]M_3

Bit 24: Output compare 6 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

CCR5

capture/compare register

Offset: 0x58, size: 32, reset: 0x00000000, access: read-write

1/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
GC5C3 rw	GC5C2 rw	GC5C1 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

Allowed values: 0x0-0xffff

GC5C1

Bit 29: Group Channel 5 and Channel 1.

GC5C2

Bit 30: Group Channel 5 and Channel 2.

GC5C3

Bit 31: Group Channel 5 and Channel 3.

CCR6

capture/compare register

Offset: 0x5c, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

Allowed values: 0x0-0xffff

OR

option registers

Offset: 0x60, size: 32, reset: 0x00000000, access: read-write

0/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
												TIM1_ETR_ADC4_RMP rw		TIM1_ETR_ADC1_RMP rw

Toggle fields

TIM1_ETR_ADC1_RMP

Bits 0-1: TIM1_ETR_ADC1 remapping capability.

TIM1_ETR_ADC4_RMP

Bits 2-3: TIM1_ETR_ADC4 remapping capability.

TIM15

0x40014000: General purpose timers

15/86 fields covered.

Toggle register map

Offset	Name	31	24	19	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	CR1									UIFREMAP		CKD		ARPE				OPM	URS	UDIS	CEN
0x4	CR2										OIS2	OIS1N	OIS1	TI1S	MMS			CCDS	CCUS		CCPC
0x8	SMCR				SMS_3									MSM	TS				SMS
0xc	DIER						TDE	COMDE			CC[2]DE	CC[1]DE	UDE	BIE	TIE	COMIE			CC[2]IE	CC[1]IE	UIE
0x10	SR										CC[2]OF	CC[1]OF		BIF	TIF	COMIF			CC[2]IF	CC[1]IF	UIF
0x14	EGR													BG	TG	COMG			CC[2]G	CC[1]G	UG
0x18	CCMR1_Input					IC[2]F				IC[2]PSC		CC[2]S		IC[1]F				IC[1]PSC		CC[1]S
0x18	CCMR1_Output		OC[2]M_3		OC[1]M_3		OC[2]M			OC[2]PE	OC[2]FE	CC[2]S			OC[1]M			OC[1]PE	OC[1]FE	CC[1]S
0x20	CCER													CC[2]NP		CC[2]P	CC[2]E	CC[1]NP	CC[1]NE	CC[1]P	CC[1]E
0x24	CNT	UIFCPY				CNT
0x28	PSC					PSC
0x2c	ARR					ARR
0x30	RCR													REP
0x34	CCR[1]					CCR
0x38	CCR[2]					CCR
0x44	BDTR			BKF		MOE	AOE	BKP	BKE	OSSR	OSSI	LOCK		DTG
0x48	DCR								DBL								DBA
0x4c	DMAR					DMAB

Toggle registers

CR1

control register 1

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

6/7 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				UIFREMAP rw		CKD rw		ARPE rw				OPM rw	URS rw	UDIS rw	CEN rw

Toggle fields

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

Allowed values:
0: AnyEvent: Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request
1: CounterOnly: Only counter overflow/underflow generates an update interrupt or DMA request

OPM

Bit 3: One-pulse mode.

Allowed values:
0: Disabled: Counter is not stopped at update event
1: Enabled: Counter stops counting at the next update event (clearing the CEN bit)

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CKD

Bits 8-9: Clock division.

Allowed values:
0: Div1: t_DTS = t_CK_INT
1: Div2: t_DTS = 2 × t_CK_INT
2: Div4: t_DTS = 4 × t_CK_INT

UIFREMAP

Bit 11: UIF status bit remapping.

CR2

control register 2

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

0/8 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
					OIS2 rw	OIS1N rw	OIS1 rw	TI1S rw	MMS rw			CCDS rw	CCUS rw		CCPC rw

Toggle fields

CCPC

Bit 0: Capture/compare preloaded control.

CCUS

Bit 2: Capture/compare control update selection.

CCDS

Bit 3: Capture/compare DMA selection.

MMS

Bits 4-6: Master mode selection.

TI1S

Bit 7: TI1 selection.

OIS1

Bit 8: Output Idle state 1.

OIS1N

Bit 9: Output Idle state 1.

OIS2

Bit 10: Output Idle state 2.

SMCR

slave mode control register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															SMS_3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								MSM rw	TS rw				SMS rw

Toggle fields

SMS

Bits 0-2: Slave mode selection.

TS

Bits 4-6: Trigger selection.

MSM

Bit 7: Master/Slave mode.

SMS_3

Bit 16: Slave mode selection bit 3.

DIER

DMA/Interrupt enable register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

1/11 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	TDE rw	COMDE rw			CC[2]DE rw	CC[1]DE rw	UDE rw	BIE rw	TIE rw	COMIE rw			CC[2]IE rw	CC[1]IE rw	UIE rw

Toggle fields

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

CC[1]IE

Bit 1: Capture/Compare 1 interrupt enable.

CC[2]IE

Bit 2: Capture/Compare 2 interrupt enable.

COMIE

Bit 5: COM interrupt enable.

TIE

Bit 6: Trigger interrupt enable.

BIE

Bit 7: Break interrupt enable.

UDE

Bit 8: Update DMA request enable.

CC[1]DE

Bit 9: Capture/Compare 1 DMA request enable.

CC[2]DE

Bit 10: Capture/Compare 2 DMA request enable.

COMDE

Bit 13: COM DMA request enable.

TDE

Bit 14: Trigger DMA request enable.

SR

status register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

1/8 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
					CC[2]OF rw	CC[1]OF rw		BIF rw	TIF rw	COMIF rw			CC[2]IF rw	CC[1]IF rw	UIF rw

Toggle fields

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: NoUpdateOccurred: No update occurred
1: UpdatePending: Update interrupt pending

CC[1]IF

Bit 1: Capture/compare 1 interrupt flag.

CC[2]IF

Bit 2: Capture/compare 2 interrupt flag.

COMIF

Bit 5: COM interrupt flag.

TIF

Bit 6: Trigger interrupt flag.

BIF

Bit 7: Break interrupt flag.

CC[1]OF

Bit 9: Capture/Compare 1 overcapture flag.

CC[2]OF

Bit 10: Capture/Compare 2 overcapture flag.

EGR

event generation register

Offset: 0x14, size: 32, reset: 0x00000000, access: write-only

1/6 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								BG w	TG w	COMG w			CC[2]G w	CC[1]G w	UG w

Toggle fields

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the registers.

CC[1]G

Bit 1: Capture/compare 1 generation.

CC[2]G

Bit 2: Capture/compare 2 generation.

COMG

Bit 5: Capture/Compare control update generation.

TG

Bit 6: Trigger generation.

BG

Bit 7: Break generation.

CCMR1_Input

capture/compare mode register 1 (input mode)

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

0/6 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IC[2]F rw				IC[2]PSC rw		CC[2]S rw		IC[1]F rw				IC[1]PSC rw		CC[1]S rw

Toggle fields

CC[1]S

Bits 0-1: Capture/Compare 1 selection.

IC[1]PSC

Bits 2-3: Input capture 1 prescaler.

IC[1]F

Bits 4-7: Input capture 1 filter.

CC[2]S

Bits 8-9: Capture/Compare 2 selection.

IC[2]PSC

Bits 10-11: Input capture 2 prescaler.

IC[2]F

Bits 12-15: Input capture 2 filter.

CCMR1_Output

capture/compare mode register (output mode)

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

4/10 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
							OC[2]M_3 rw								OC[1]M_3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	OC[2]M rw			OC[2]PE rw	OC[2]FE rw	CC[2]S rw			OC[1]M rw			OC[1]PE rw	OC[1]FE rw	CC[1]S rw

Toggle fields

CC[1]S

Bits 0-1: Capture/Compare 1 selection.

OC[1]FE

Bit 2: Output compare 1 fast enable.

OC[1]PE

Bit 3: Output compare 1 preload enable.

OC[1]M

Bits 4-6: Output compare 1 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / Reserved
7: PwmMode2: Inversely to PwmMode1 / Reserved

CC[2]S

Bits 8-9: Capture/Compare 2 selection.

OC[2]FE

Bit 10: Output compare 2 fast enable.

OC[2]PE

Bit 11: Output compare 2 preload enable.

OC[2]M

Bits 12-14: Output compare 2 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / Reserved
7: PwmMode2: Inversely to PwmMode1 / Reserved

OC[1]M_3

Bit 16: Output compare 1 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

OC[2]M_3

Bit 24: Output compare 2 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

CCER

capture/compare enable register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

0/7 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								CC[2]NP rw		CC[2]P rw	CC[2]E rw	CC[1]NP rw	CC[1]NE rw	CC[1]P rw	CC[1]E rw

Toggle fields

CC[1]E

Bit 0: Capture/Compare 1 output enable.

CC[1]P

Bit 1: Capture/Compare 1 output Polarity.

CC[1]NE

Bit 2: Capture/Compare 1 complementary output enable.

CC[1]NP

Bit 3: Capture/Compare 1 output Polarity.

CC[2]E

Bit 4: Capture/Compare 2 output enable.

CC[2]P

Bit 5: Capture/Compare 2 output Polarity.

CC[2]NP

Bit 7: Capture/Compare 2 output Polarity.

CNT

counter

Offset: 0x24, size: 32, reset: 0x00000000, access: Unspecified

1/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
UIFCPY r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CNT rw

Toggle fields

CNT

Bits 0-15: counter value.

UIFCPY

Bit 31: UIF copy.

PSC

prescaler

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PSC rw

Toggle fields

PSC

Bits 0-15: Prescaler value.

Allowed values: 0x0-0xffff

ARR

auto-reload register

Offset: 0x2c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ARR rw

Toggle fields

ARR

Bits 0-15: Auto-reload value.

RCR

repetition counter register

Offset: 0x30, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								REP rw

Toggle fields

REP

Bits 0-7: Repetition counter value.

CCR[1]

capture/compare register

Offset: 0x34, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

CCR[2]

capture/compare register

Offset: 0x38, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

BDTR

break and dead-time register

Offset: 0x44, size: 32, reset: 0x00000000, access: read-write

0/9 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
												BKF rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MOE rw	AOE rw	BKP rw	BKE rw	OSSR rw	OSSI rw	LOCK rw		DTG rw

Toggle fields

DTG

Bits 0-7: Dead-time generator setup.

LOCK

Bits 8-9: Lock configuration.

OSSI

Bit 10: Off-state selection for Idle mode.

OSSR

Bit 11: Off-state selection for Run mode.

BKE

Bit 12: Break enable.

BKP

Bit 13: Break polarity.

AOE

Bit 14: Automatic output enable.

MOE

Bit 15: Main output enable.

BKF

Bits 16-19: Break filter.

DCR

DMA control register

Offset: 0x48, size: 32, reset: 0x00000000, access: read-write

0/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			DBL rw								DBA rw

Toggle fields

DBA

Bits 0-4: DMA base address.

DBL

Bits 8-12: DMA burst length.

DMAR

DMA address for full transfer

Offset: 0x4c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DMAB rw

Toggle fields

DMAB

Bits 0-15: DMA register for burst accesses.

TIM16

0x40014400: General-purpose-timers

21/62 fields covered.

Toggle register map

Offset	Name	31	19	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	CR1								UIFREMAP		CKD		ARPE				OPM	URS	UDIS	CEN
0x4	CR2										OIS1N	OIS1					CCDS	CCUS		CCPC
0xc	DIER					TDE	COMDE				CC[1]DE	UDE	BIE	TIE	COMIE				CC[1]IE	UIE
0x10	SR										CC[1]OF		BIF	TIF	COMIF				CC[1]IF	UIF
0x14	EGR												BG	TG	COMG				CC[1]G	UG
0x18	CCMR1_Input												IC[1]F				IC[1]PSC		CC[1]S
0x18	CCMR1_Output			OC[1]M_3										OC[1]M			OC[1]PE	OC[1]FE	CC[1]S
0x20	CCER																CC[1]NP	CC[1]NE	CC[1]P	CC[1]E
0x24	CNT	UIFCPY			CNT
0x28	PSC				PSC
0x2c	ARR				ARR
0x30	RCR												REP
0x34	CCR[1]				CCR
0x44	BDTR		BKF		MOE	AOE	BKP	BKE	OSSR	OSSI	LOCK		DTG
0x48	DCR							DBL								DBA
0x4c	DMAR				DMAB
0x50	OR

Toggle registers

CR1

control register 1

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

6/7 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				UIFREMAP rw		CKD rw		ARPE rw				OPM rw	URS rw	UDIS rw	CEN rw

Toggle fields

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

Allowed values:
0: AnyEvent: Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request
1: CounterOnly: Only counter overflow/underflow generates an update interrupt or DMA request

OPM

Bit 3: One-pulse mode.

Allowed values:
0: Disabled: Counter is not stopped at update event
1: Enabled: Counter stops counting at the next update event (clearing the CEN bit)

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CKD

Bits 8-9: Clock division.

Allowed values:
0: Div1: t_DTS = t_CK_INT
1: Div2: t_DTS = 2 × t_CK_INT
2: Div4: t_DTS = 4 × t_CK_INT

UIFREMAP

Bit 11: UIF status bit remapping.

CR2

control register 2

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

5/5 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						OIS1N rw	OIS1 rw					CCDS rw	CCUS rw		CCPC rw

Toggle fields

CCPC

Bit 0: Capture/compare preloaded control.

Allowed values:
0: NotPreloaded: CCxE, CCxNE and OCxM bits are not preloaded
1: Preloaded: CCxE, CCxNE and OCxM bits are preloaded

CCUS

Bit 2: Capture/compare control update selection.

Allowed values:
0: Default: Capture/compare are updated only by setting the COMG bit
1: WithRisingEdge: Capture/compare are updated by setting the COMG bit or when an rising edge occurs on TRGI

CCDS

Bit 3: Capture/compare DMA selection.

Allowed values:
0: OnCompare: CCx DMA request sent when CCx event occurs
1: OnUpdate: CCx DMA request sent when update event occurs

OIS1

Bit 8: Output Idle state 1.

Allowed values:
0: Reset: OC1=0 (after a dead-time if OC1N is implemented) when MOE=0
1: Set: OC1=1 (after a dead-time if OC1N is implemented) when MOE=0

OIS1N

Bit 9: Output Idle state 1.

Allowed values:
0: Reset: OC1N=0 after a dead-time when MOE=0
1: Set: OC1N=1 after a dead-time when MOE=0

DIER

DMA/Interrupt enable register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

5/9 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	TDE rw	COMDE rw				CC[1]DE rw	UDE rw	BIE rw	TIE rw	COMIE rw				CC[1]IE rw	UIE rw

Toggle fields

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

CC[1]IE

Bit 1: Capture/Compare 1 interrupt enable.

Allowed values:
0: Disabled: CC1 interrupt disabled
1: Enabled: CC1 interrupt enabled

COMIE

Bit 5: COM interrupt enable.

Allowed values:
0: Disabled: COM interrupt disabled
1: Enabled: COM interrupt enabled

TIE

Bit 6: Trigger interrupt enable.

BIE

Bit 7: Break interrupt enable.

Allowed values:
0: Disabled: Break interrupt disabled
1: Enabled: Break interrupt enabled

UDE

Bit 8: Update DMA request enable.

CC[1]DE

Bit 9: Capture/Compare 1 DMA request enable.

Allowed values:
0: Disabled: CC1 DMA request disabled
1: Enabled: CC1 DMA request enabled

COMDE

Bit 13: COM DMA request enable.

TDE

Bit 14: Trigger DMA request enable.

SR

status register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

1/6 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						CC[1]OF rw		BIF rw	TIF rw	COMIF rw				CC[1]IF rw	UIF rw

Toggle fields

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: NoUpdateOccurred: No update occurred
1: UpdatePending: Update interrupt pending

CC[1]IF

Bit 1: Capture/compare 1 interrupt flag.

COMIF

Bit 5: COM interrupt flag.

TIF

Bit 6: Trigger interrupt flag.

BIF

Bit 7: Break interrupt flag.

CC[1]OF

Bit 9: Capture/Compare 1 overcapture flag.

EGR

event generation register

Offset: 0x14, size: 32, reset: 0x00000000, access: write-only

1/5 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								BG w	TG w	COMG w				CC[1]G w	UG w

Toggle fields

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the registers.

CC[1]G

Bit 1: Capture/compare 1 generation.

COMG

Bit 5: Capture/Compare control update generation.

TG

Bit 6: Trigger generation.

BG

Bit 7: Break generation.

CCMR1_Input

capture/compare mode register 1 (input mode)

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

0/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								IC[1]F rw				IC[1]PSC rw		CC[1]S rw

Toggle fields

CC[1]S

Bits 0-1: Capture/Compare 1 selection.

IC[1]PSC

Bits 2-3: Input capture 1 prescaler.

IC[1]F

Bits 4-7: Input capture 1 filter.

CCMR1_Output

capture/compare mode register (output mode)

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

1/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															OC[1]M_3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
									OC[1]M rw			OC[1]PE rw	OC[1]FE rw	CC[1]S rw

Toggle fields

CC[1]S

Bits 0-1: Capture/Compare 1 selection.

OC[1]FE

Bit 2: Output compare 1 fast enable.

OC[1]PE

Bit 3: Output compare 1 preload enable.

OC[1]M

Bits 4-6: Output compare 1 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy
4: ForceInactive: OCyREF is forced low
5: ForceActive: OCyREF is forced high
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active
7: PwmMode2: Inversely to PwmMode1

OC[1]M_3

Bit 16: Output compare 1 mode, bit 3.

CCER

capture/compare enable register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
												CC[1]NP rw	CC[1]NE rw	CC[1]P rw	CC[1]E rw

Toggle fields

CC[1]E

Bit 0: Capture/Compare 1 output enable.

CC[1]P

Bit 1: Capture/Compare 1 output Polarity.

CC[1]NE

Bit 2: Capture/Compare 1 complementary output enable.

CC[1]NP

Bit 3: Capture/Compare 1 output Polarity.

CNT

counter

Offset: 0x24, size: 32, reset: 0x00000000, access: Unspecified

1/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
UIFCPY r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CNT rw

Toggle fields

CNT

Bits 0-15: counter value.

UIFCPY

Bit 31: UIF Copy.

PSC

prescaler

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PSC rw

Toggle fields

PSC

Bits 0-15: Prescaler value.

Allowed values: 0x0-0xffff

ARR

auto-reload register

Offset: 0x2c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ARR rw

Toggle fields

ARR

Bits 0-15: Auto-reload value.

RCR

repetition counter register

Offset: 0x30, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								REP rw

Toggle fields

REP

Bits 0-7: Repetition counter value.

CCR[1]

capture/compare register

Offset: 0x34, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

BDTR

break and dead-time register

Offset: 0x44, size: 32, reset: 0x00000000, access: read-write

0/9 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
												BKF rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MOE rw	AOE rw	BKP rw	BKE rw	OSSR rw	OSSI rw	LOCK rw		DTG rw

Toggle fields

DTG

Bits 0-7: Dead-time generator setup.

LOCK

Bits 8-9: Lock configuration.

OSSI

Bit 10: Off-state selection for Idle mode.

OSSR

Bit 11: Off-state selection for Run mode.

BKE

Bit 12: Break enable.

BKP

Bit 13: Break polarity.

AOE

Bit 14: Automatic output enable.

MOE

Bit 15: Main output enable.

BKF

Bits 16-19: Break filter.

DCR

DMA control register

Offset: 0x48, size: 32, reset: 0x00000000, access: read-write

0/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			DBL rw								DBA rw

Toggle fields

DBA

Bits 0-4: DMA base address.

DBL

Bits 8-12: DMA burst length.

DMAR

DMA address for full transfer

Offset: 0x4c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DMAB rw

Toggle fields

DMAB

Bits 0-15: DMA register for burst accesses.

OR

option register

Offset: 0x50, size: 32, reset: 0x00000000, access: read-write

Toggle fields

TIM17

0x40014800: General purpose timer

12/62 fields covered.

Toggle register map

Offset	Name	31	19	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	CR1								UIFREMAP		CKD		ARPE				OPM	URS	UDIS	CEN
0x4	CR2										OIS1N	OIS1					CCDS	CCUS		CCPC
0xc	DIER					TDE	COMDE				CC[1]DE	UDE	BIE	TIE	COMIE				CC[1]IE	UIE
0x10	SR										CC[1]OF		BIF	TIF	COMIF				CC[1]IF	UIF
0x14	EGR												BG	TG	COMG				CC[1]G	UG
0x18	CCMR1_Input												IC[1]F				IC[1]PSC		CC[1]S
0x18	CCMR1_Output			OC[1]M_3										OC[1]M			OC[1]PE	OC[1]FE	CC[1]S
0x20	CCER																CC[1]NP	CC[1]NE	CC[1]P	CC[1]E
0x24	CNT	UIFCPY			CNT
0x28	PSC				PSC
0x2c	ARR				ARR
0x30	RCR												REP
0x34	CCR[1]				CCR
0x44	BDTR		BKF		MOE	AOE	BKP	BKE	OSSR	OSSI	LOCK		DTG
0x48	DCR							DBL								DBA
0x4c	DMAR				DMAB

Toggle registers

CR1

control register 1

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

6/7 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				UIFREMAP rw		CKD rw		ARPE rw				OPM rw	URS rw	UDIS rw	CEN rw

Toggle fields

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

Allowed values:
0: AnyEvent: Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request
1: CounterOnly: Only counter overflow/underflow generates an update interrupt or DMA request

OPM

Bit 3: One-pulse mode.

Allowed values:
0: Disabled: Counter is not stopped at update event
1: Enabled: Counter stops counting at the next update event (clearing the CEN bit)

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CKD

Bits 8-9: Clock division.

Allowed values:
0: Div1: t_DTS = t_CK_INT
1: Div2: t_DTS = 2 × t_CK_INT
2: Div4: t_DTS = 4 × t_CK_INT

UIFREMAP

Bit 11: UIF status bit remapping.

CR2

control register 2

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

0/5 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						OIS1N rw	OIS1 rw					CCDS rw	CCUS rw		CCPC rw

Toggle fields

CCPC

Bit 0: Capture/compare preloaded control.

CCUS

Bit 2: Capture/compare control update selection.

CCDS

Bit 3: Capture/compare DMA selection.

OIS1

Bit 8: Output Idle state 1.

OIS1N

Bit 9: Output Idle state 1.

DIER

DMA/Interrupt enable register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

1/9 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	TDE rw	COMDE rw				CC[1]DE rw	UDE rw	BIE rw	TIE rw	COMIE rw				CC[1]IE rw	UIE rw

Toggle fields

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

CC[1]IE

Bit 1: Capture/Compare 1 interrupt enable.

COMIE

Bit 5: COM interrupt enable.

TIE

Bit 6: Trigger interrupt enable.

BIE

Bit 7: Break interrupt enable.

UDE

Bit 8: Update DMA request enable.

CC[1]DE

Bit 9: Capture/Compare 1 DMA request enable.

COMDE

Bit 13: COM DMA request enable.

TDE

Bit 14: Trigger DMA request enable.

SR

status register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

1/6 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						CC[1]OF rw		BIF rw	TIF rw	COMIF rw				CC[1]IF rw	UIF rw

Toggle fields

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: NoUpdateOccurred: No update occurred
1: UpdatePending: Update interrupt pending

CC[1]IF

Bit 1: Capture/compare 1 interrupt flag.

COMIF

Bit 5: COM interrupt flag.

TIF

Bit 6: Trigger interrupt flag.

BIF

Bit 7: Break interrupt flag.

CC[1]OF

Bit 9: Capture/Compare 1 overcapture flag.

EGR

event generation register

Offset: 0x14, size: 32, reset: 0x00000000, access: write-only

1/5 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								BG w	TG w	COMG w				CC[1]G w	UG w

Toggle fields

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the registers.

CC[1]G

Bit 1: Capture/compare 1 generation.

COMG

Bit 5: Capture/Compare control update generation.

TG

Bit 6: Trigger generation.

BG

Bit 7: Break generation.

CCMR1_Input

capture/compare mode register 1 (input mode)

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

0/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								IC[1]F rw				IC[1]PSC rw		CC[1]S rw

Toggle fields

CC[1]S

Bits 0-1: Capture/Compare 1 selection.

IC[1]PSC

Bits 2-3: Input capture 1 prescaler.

IC[1]F

Bits 4-7: Input capture 1 filter.

CCMR1_Output

capture/compare mode register (output mode)

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

1/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															OC[1]M_3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
									OC[1]M rw			OC[1]PE rw	OC[1]FE rw	CC[1]S rw

Toggle fields

CC[1]S

Bits 0-1: Capture/Compare 1 selection.

OC[1]FE

Bit 2: Output compare 1 fast enable.

OC[1]PE

Bit 3: Output compare 1 preload enable.

OC[1]M

Bits 4-6: Output compare 1 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy
4: ForceInactive: OCyREF is forced low
5: ForceActive: OCyREF is forced high
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active
7: PwmMode2: Inversely to PwmMode1

OC[1]M_3

Bit 16: Output compare 1 mode, bit 3.

CCER

capture/compare enable register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
												CC[1]NP rw	CC[1]NE rw	CC[1]P rw	CC[1]E rw

Toggle fields

CC[1]E

Bit 0: Capture/Compare 1 output enable.

CC[1]P

Bit 1: Capture/Compare 1 output Polarity.

CC[1]NE

Bit 2: Capture/Compare 1 complementary output enable.

CC[1]NP

Bit 3: Capture/Compare 1 output Polarity.

CNT

counter

Offset: 0x24, size: 32, reset: 0x00000000, access: Unspecified

1/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
UIFCPY r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CNT rw

Toggle fields

CNT

Bits 0-15: counter value.

UIFCPY

Bit 31: UIF Copy.

PSC

prescaler

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PSC rw

Toggle fields

PSC

Bits 0-15: Prescaler value.

Allowed values: 0x0-0xffff

ARR

auto-reload register

Offset: 0x2c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ARR rw

Toggle fields

ARR

Bits 0-15: Auto-reload value.

RCR

repetition counter register

Offset: 0x30, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								REP rw

Toggle fields

REP

Bits 0-7: Repetition counter value.

CCR[1]

capture/compare register

Offset: 0x34, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

BDTR

break and dead-time register

Offset: 0x44, size: 32, reset: 0x00000000, access: read-write

0/9 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
												BKF rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MOE rw	AOE rw	BKP rw	BKE rw	OSSR rw	OSSI rw	LOCK rw		DTG rw

Toggle fields

DTG

Bits 0-7: Dead-time generator setup.

LOCK

Bits 8-9: Lock configuration.

OSSI

Bit 10: Off-state selection for Idle mode.

OSSR

Bit 11: Off-state selection for Run mode.

BKE

Bit 12: Break enable.

BKP

Bit 13: Break polarity.

AOE

Bit 14: Automatic output enable.

MOE

Bit 15: Main output enable.

BKF

Bits 16-19: Break filter.

DCR

DMA control register

Offset: 0x48, size: 32, reset: 0x00000000, access: read-write

0/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			DBL rw								DBA rw

Toggle fields

DBA

Bits 0-4: DMA base address.

DBL

Bits 8-12: DMA burst length.

DMAR

DMA address for full transfer

Offset: 0x4c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DMAB rw

Toggle fields

DMAB

Bits 0-15: DMA register for burst accesses.

TIM2

0x40000000: General purpose timer

81/107 fields covered.

Toggle register map

Offset	Name	31	24	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	CR1								UIFREMAP		CKD		ARPE	CMS		DIR	OPM	URS	UDIS	CEN
0x4	CR2												TI1S	MMS			CCDS
0x8	SMCR			SMS_3	ETP	ECE	ETPS		ETF				MSM	TS			OCCS	SMS
0xc	DIER					TDE		CC[4]DE	CC[3]DE	CC[2]DE	CC[1]DE	UDE		TIE		CC[4]IE	CC[3]IE	CC[2]IE	CC[1]IE	UIE
0x10	SR							CC[4]OF	CC[3]OF	CC[2]OF	CC[1]OF			TIF		CC[4]IF	CC[3]IF	CC[2]IF	CC[1]IF	UIF
0x14	EGR													TG		CC[4]G	CC[3]G	CC[2]G	CC[1]G	UG
0x18	CCMR1_Input				IC[2]F				IC[2]PSC		CC[2]S		IC[1]F				IC[1]PSC		CC[1]S
0x18	CCMR1_Output		OC[2]M_3	OC[1]M_3	OC[2]CE	OC[2]M			OC[2]PE	OC[2]FE	CC[2]S		OC[1]CE	OC[1]M			OC[1]PE	OC[1]FE	CC[1]S
0x1c	CCMR2_Input				IC[4]F				IC[4]PSC		CC[4]S		IC[3]F				IC[3]PSC		CC[3]S
0x1c	CCMR2_Output		OC[4]M_3	OC[3]M_3	OC[4]CE	OC[4]M			OC[4]PE	OC[4]FE	CC[4]S		OC[3]CE	OC[3]M			OC[3]PE	OC[3]FE	CC[3]S
0x20	CCER				CC[4]NP		CC[4]P	CC[4]E	CC[3]NP		CC[3]P	CC[3]E	CC[2]NP		CC[2]P	CC[2]E	CC[1]NP		CC[1]P	CC[1]E
0x24	CNT	CNT			CNT
0x28	PSC				PSC
0x2c	ARR	ARR			ARR
0x34	CCR[1]	CCR			CCR
0x38	CCR[2]	CCR			CCR
0x3c	CCR[3]	CCR			CCR
0x40	CCR[4]	CCR			CCR
0x48	DCR							DBL								DBA
0x4c	DMAR				DMAB

Toggle registers

CR1

control register 1

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

8/9 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				UIFREMAP rw		CKD rw		ARPE rw	CMS rw		DIR rw	OPM rw	URS rw	UDIS rw	CEN rw

Toggle fields

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

Allowed values:
0: AnyEvent: Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request
1: CounterOnly: Only counter overflow/underflow generates an update interrupt or DMA request

OPM

Bit 3: One-pulse mode.

Allowed values:
0: Disabled: Counter is not stopped at update event
1: Enabled: Counter stops counting at the next update event (clearing the CEN bit)

DIR

Bit 4: Direction.

Allowed values:
0: Up: Counter used as upcounter
1: Down: Counter used as downcounter

CMS

Bits 5-6: Center-aligned mode selection.

Allowed values:
0: EdgeAligned: The counter counts up or down depending on the direction bit
1: CenterAligned1: The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting down.
2: CenterAligned2: The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting up.
3: CenterAligned3: The counter counts up and down alternatively. Output compare interrupt flags are set both when the counter is counting up or down.

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CKD

Bits 8-9: Clock division.

Allowed values:
0: Div1: t_DTS = t_CK_INT
1: Div2: t_DTS = 2 × t_CK_INT
2: Div4: t_DTS = 4 × t_CK_INT

UIFREMAP

Bit 11: UIF status bit remapping.

CR2

control register 2

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

3/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								TI1S rw	MMS rw			CCDS rw

Toggle fields

CCDS

Bit 3: Capture/compare DMA selection.

Allowed values:
0: OnCompare: CCx DMA request sent when CCx event occurs
1: OnUpdate: CCx DMA request sent when update event occurs

MMS

Bits 4-6: Master mode selection.

Allowed values:
0: Reset: The UG bit from the TIMx_EGR register is used as trigger output
1: Enable: The counter enable signal, CNT_EN, is used as trigger output
2: Update: The update event is selected as trigger output
3: ComparePulse: The trigger output send a positive pulse when the CC1IF flag it to be set, as soon as a capture or a compare match occurred
4: CompareOC1: OC1REF signal is used as trigger output
5: CompareOC2: OC2REF signal is used as trigger output
6: CompareOC3: OC3REF signal is used as trigger output
7: CompareOC4: OC4REF signal is used as trigger output

TI1S

Bit 7: TI1 selection.

Allowed values:
0: Normal: The TIMx_CH1 pin is connected to TI1 input
1: XOR: The TIMx_CH1, CH2, CH3 pins are connected to TI1 input

SMCR

slave mode control register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

7/9 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															SMS_3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ETP rw	ECE rw	ETPS rw		ETF rw				MSM rw	TS rw			OCCS rw	SMS rw

Toggle fields

SMS

Bits 0-2: Slave mode selection.

Allowed values:
0: Disabled: Slave mode disabled - if CEN = ‘1 then the prescaler is clocked directly by the internal clock.
1: Encoder_Mode_1: Encoder mode 1 - Counter counts up/down on TI2FP1 edge depending on TI1FP2 level.
2: Encoder_Mode_2: Encoder mode 2 - Counter counts up/down on TI1FP2 edge depending on TI2FP1 level.
3: Encoder_Mode_3: Encoder mode 3 - Counter counts up/down on both TI1FP1 and TI2FP2 edges depending on the level of the other input.
4: Reset_Mode: Reset Mode - Rising edge of the selected trigger input (TRGI) reinitializes the counter and generates an update of the registers.
5: Gated_Mode: Gated Mode - The counter clock is enabled when the trigger input (TRGI) is high. The counter stops (but is not reset) as soon as the trigger becomes low. Both start and stop of the counter are controlled.
6: Trigger_Mode: Trigger Mode - The counter starts at a rising edge of the trigger TRGI (but it is not reset). Only the start of the counter is controlled.
7: Ext_Clock_Mode: External Clock Mode 1 - Rising edges of the selected trigger (TRGI) clock the counter.

OCCS

Bit 3: OCREF clear selection.

TS

Bits 4-6: Trigger selection.

Allowed values:
0: ITR0: Internal Trigger 0 (ITR0)
1: ITR1: Internal Trigger 1 (ITR1)
2: ITR2: Internal Trigger 2 (ITR2)
4: TI1F_ED: TI1 Edge Detector (TI1F_ED)
5: TI1FP1: Filtered Timer Input 1 (TI1FP1)
6: TI2FP2: Filtered Timer Input 2 (TI2FP2)
7: ETRF: External Trigger input (ETRF)

MSM

Bit 7: Master/Slave mode.

Allowed values:
0: NoSync: No action
1: Sync: The effect of an event on the trigger input (TRGI) is delayed to allow a perfect synchronization between the current timer and its slaves (through TRGO). It is useful if we want to synchronize several timers on a single external event.

ETF

Bits 8-11: External trigger filter.

Allowed values:
0: NoFilter: No filter, sampling is done at fDTS
1: FCK_INT_N2: fSAMPLING=fCK_INT, N=2
2: FCK_INT_N4: fSAMPLING=fCK_INT, N=4
3: FCK_INT_N8: fSAMPLING=fCK_INT, N=8
4: FDTS_Div2_N6: fSAMPLING=fDTS/2, N=6
5: FDTS_Div2_N8: fSAMPLING=fDTS/2, N=8
6: FDTS_Div4_N6: fSAMPLING=fDTS/4, N=6
7: FDTS_Div4_N8: fSAMPLING=fDTS/4, N=8
8: FDTS_Div8_N6: fSAMPLING=fDTS/8, N=6
9: FDTS_Div8_N8: fSAMPLING=fDTS/8, N=8
10: FDTS_Div16_N5: fSAMPLING=fDTS/16, N=5
11: FDTS_Div16_N6: fSAMPLING=fDTS/16, N=6
12: FDTS_Div16_N8: fSAMPLING=fDTS/16, N=8
13: FDTS_Div32_N5: fSAMPLING=fDTS/32, N=5
14: FDTS_Div32_N6: fSAMPLING=fDTS/32, N=6
15: FDTS_Div32_N8: fSAMPLING=fDTS/32, N=8

ETPS

Bits 12-13: External trigger prescaler.

Allowed values:
0: Div1: Prescaler OFF
1: Div2: ETRP frequency divided by 2
2: Div4: ETRP frequency divided by 4
3: Div8: ETRP frequency divided by 8

ECE

Bit 14: External clock enable.

Allowed values:
0: Disabled: External clock mode 2 disabled
1: Enabled: External clock mode 2 enabled. The counter is clocked by any active edge on the ETRF signal.

ETP

Bit 15: External trigger polarity.

Allowed values:
0: NotInverted: ETR is noninverted, active at high level or rising edge
1: Inverted: ETR is inverted, active at low level or falling edge

SMS_3

Bit 16: Slave mode selection bit3.

DIER

DMA/Interrupt enable register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

12/12 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	TDE rw		CC[4]DE rw	CC[3]DE rw	CC[2]DE rw	CC[1]DE rw	UDE rw		TIE rw		CC[4]IE rw	CC[3]IE rw	CC[2]IE rw	CC[1]IE rw	UIE rw

Toggle fields

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

CC[1]IE

Bit 1: Capture/Compare 1 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC[2]IE

Bit 2: Capture/Compare 2 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC[3]IE

Bit 3: Capture/Compare 3 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC[4]IE

Bit 4: Capture/Compare 4 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

TIE

Bit 6: Trigger interrupt enable.

Allowed values:
0: Disabled: Trigger interrupt disabled
1: Enabled: Trigger interrupt enabled

UDE

Bit 8: Update DMA request enable.

Allowed values:
0: Disabled: Update DMA request disabled
1: Enabled: Update DMA request enabled

CC[1]DE

Bit 9: Capture/Compare 1 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC[2]DE

Bit 10: Capture/Compare 2 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC[3]DE

Bit 11: Capture/Compare 3 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC[4]DE

Bit 12: Capture/Compare 4 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

TDE

Bit 14: Trigger DMA request enable.

Allowed values:
0: Disabled: Trigger DMA request disabled
1: Enabled: Trigger DMA request enabled

SR

status register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

10/10 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			CC[4]OF rw	CC[3]OF rw	CC[2]OF rw	CC[1]OF rw			TIF rw		CC[4]IF rw	CC[3]IF rw	CC[2]IF rw	CC[1]IF rw	UIF rw

Toggle fields

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: NoUpdateOccurred: No update occurred
1: UpdatePending: Update interrupt pending

CC[1]IF

Bit 1: Capture/compare 1 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC[2]IF

Bit 2: Capture/compare 2 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC[3]IF

Bit 3: Capture/compare 3 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC[4]IF

Bit 4: Capture/compare 4 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

TIF

Bit 6: Trigger interrupt flag.

Allowed values:
0: NoTrigger: No trigger event occurred
1: Trigger: Trigger interrupt pending

CC[1]OF

Bit 9: Capture/Compare 1 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC[2]OF

Bit 10: Capture/Compare 2 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC[3]OF

Bit 11: Capture/Compare 3 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC[4]OF

Bit 12: Capture/Compare 4 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

EGR

event generation register

Offset: 0x14, size: 32, reset: 0x00000000, access: write-only

6/6 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
									TG w		CC[4]G w	CC[3]G w	CC[2]G w	CC[1]G w	UG w

Toggle fields

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the registers.

CC[1]G

Bit 1: Capture/compare 1 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC[2]G

Bit 2: Capture/compare 2 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC[3]G

Bit 3: Capture/compare 3 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC[4]G

Bit 4: Capture/compare 4 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

TG

Bit 6: Trigger generation.

Allowed values:
1: Trigger: The TIF flag is set in TIMx_SR register. Related interrupt or DMA transfer can occur if enabled.

CCMR1_Input

capture/compare mode register 1 (input mode)

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

4/6 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IC[2]F rw				IC[2]PSC rw		CC[2]S rw		IC[1]F rw				IC[1]PSC rw		CC[1]S rw

Toggle fields

CC[1]S

Bits 0-1: Capture/Compare 1 selection.

Allowed values:
1: TI1: CC1 channel is configured as input, IC1 is mapped on TI1
2: TI2: CC1 channel is configured as input, IC1 is mapped on TI2
3: TRC: CC1 channel is configured as input, IC1 is mapped on TRC

IC[1]PSC

Bits 2-3: Input capture 1 prescaler.

IC[1]F

Bits 4-7: Input capture 1 filter.

Allowed values:
0: NoFilter: No filter, sampling is done at fDTS
1: FCK_INT_N2: fSAMPLING=fCK_INT, N=2
2: FCK_INT_N4: fSAMPLING=fCK_INT, N=4
3: FCK_INT_N8: fSAMPLING=fCK_INT, N=8
4: FDTS_Div2_N6: fSAMPLING=fDTS/2, N=6
5: FDTS_Div2_N8: fSAMPLING=fDTS/2, N=8
6: FDTS_Div4_N6: fSAMPLING=fDTS/4, N=6
7: FDTS_Div4_N8: fSAMPLING=fDTS/4, N=8
8: FDTS_Div8_N6: fSAMPLING=fDTS/8, N=6
9: FDTS_Div8_N8: fSAMPLING=fDTS/8, N=8
10: FDTS_Div16_N5: fSAMPLING=fDTS/16, N=5
11: FDTS_Div16_N6: fSAMPLING=fDTS/16, N=6
12: FDTS_Div16_N8: fSAMPLING=fDTS/16, N=8
13: FDTS_Div32_N5: fSAMPLING=fDTS/32, N=5
14: FDTS_Div32_N6: fSAMPLING=fDTS/32, N=6
15: FDTS_Div32_N8: fSAMPLING=fDTS/32, N=8

CC[2]S

Bits 8-9: Capture/Compare 2 selection.

Allowed values:
1: TI1: CC1 channel is configured as input, IC1 is mapped on TI1
2: TI2: CC1 channel is configured as input, IC1 is mapped on TI2
3: TRC: CC1 channel is configured as input, IC1 is mapped on TRC

IC[2]PSC

Bits 10-11: Input capture 2 prescaler.

IC[2]F

Bits 12-15: Input capture 2 filter.

Allowed values:
0: NoFilter: No filter, sampling is done at fDTS
1: FCK_INT_N2: fSAMPLING=fCK_INT, N=2
2: FCK_INT_N4: fSAMPLING=fCK_INT, N=4
3: FCK_INT_N8: fSAMPLING=fCK_INT, N=8
4: FDTS_Div2_N6: fSAMPLING=fDTS/2, N=6
5: FDTS_Div2_N8: fSAMPLING=fDTS/2, N=8
6: FDTS_Div4_N6: fSAMPLING=fDTS/4, N=6
7: FDTS_Div4_N8: fSAMPLING=fDTS/4, N=8
8: FDTS_Div8_N6: fSAMPLING=fDTS/8, N=6
9: FDTS_Div8_N8: fSAMPLING=fDTS/8, N=8
10: FDTS_Div16_N5: fSAMPLING=fDTS/16, N=5
11: FDTS_Div16_N6: fSAMPLING=fDTS/16, N=6
12: FDTS_Div16_N8: fSAMPLING=fDTS/16, N=8
13: FDTS_Div32_N5: fSAMPLING=fDTS/32, N=5
14: FDTS_Div32_N6: fSAMPLING=fDTS/32, N=6
15: FDTS_Div32_N8: fSAMPLING=fDTS/32, N=8

CCMR1_Output

capture/compare mode register 1 (output mode)

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

8/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
							OC[2]M_3 rw								OC[1]M_3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OC[2]CE rw	OC[2]M rw			OC[2]PE rw	OC[2]FE rw	CC[2]S rw		OC[1]CE rw	OC[1]M rw			OC[1]PE rw	OC[1]FE rw	CC[1]S rw

Toggle fields

CC[1]S

Bits 0-1: Capture/Compare 1 selection.

Allowed values:
0: Output: CC1 channel is configured as output

OC[1]FE

Bit 2: Output compare 1 fast enable.

OC[1]PE

Bit 3: Output compare 1 preload enable.

Allowed values:
0: Disabled: Preload register on CCR1 disabled. New values written to CCR1 are taken into account immediately
1: Enabled: Preload register on CCR1 enabled. Preload value is loaded into active register on each update event

OC[1]M

Bits 4-6: Output compare 1 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[1]CE

Bit 7: Output compare 1 clear enable.

CC[2]S

Bits 8-9: Capture/Compare 2 selection.

Allowed values:
0: Output: CC1 channel is configured as output

OC[2]FE

Bit 10: Output compare 2 fast enable.

OC[2]PE

Bit 11: Output compare 2 preload enable.

Allowed values:
0: Disabled: Preload register on CCR1 disabled. New values written to CCR1 are taken into account immediately
1: Enabled: Preload register on CCR1 enabled. Preload value is loaded into active register on each update event

OC[2]M

Bits 12-14: Output compare 2 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[2]CE

Bit 15: Output compare 2 clear enable.

OC[1]M_3

Bit 16: Output compare 1 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

OC[2]M_3

Bit 24: Output compare 2 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

CCMR2_Input

capture/compare mode register 2 (input mode)

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

6/6 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IC[4]F rw				IC[4]PSC rw		CC[4]S rw		IC[3]F rw				IC[3]PSC rw		CC[3]S rw

Toggle fields

CC[3]S

Bits 0-1: Capture/Compare 3 selection.

Allowed values:
1: TI3: CC3 channel is configured as input, IC3 is mapped on TI3
2: TI4: CC3 channel is configured as input, IC3 is mapped on TI4
3: TRC: CC3 channel is configured as input, IC3 is mapped on TRC

IC[3]PSC

Bits 2-3: Input capture 3 prescaler.

Allowed values: 0x0-0x3

IC[3]F

Bits 4-7: Input capture 3 filter.

Allowed values: 0x0-0xf

CC[4]S

Bits 8-9: Capture/Compare 4 selection.

Allowed values:
1: TI3: CC3 channel is configured as input, IC3 is mapped on TI3
2: TI4: CC3 channel is configured as input, IC3 is mapped on TI4
3: TRC: CC3 channel is configured as input, IC3 is mapped on TRC

IC[4]PSC

Bits 10-11: Input capture 4 prescaler.

Allowed values: 0x0-0x3

IC[4]F

Bits 12-15: Input capture 4 filter.

Allowed values: 0x0-0xf

CCMR2_Output

capture/compare mode register 2 (output mode)

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

8/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
							OC[4]M_3 rw								OC[3]M_3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OC[4]CE rw	OC[4]M rw			OC[4]PE rw	OC[4]FE rw	CC[4]S rw		OC[3]CE rw	OC[3]M rw			OC[3]PE rw	OC[3]FE rw	CC[3]S rw

Toggle fields

CC[3]S

Bits 0-1: Capture/Compare 3 selection.

Allowed values:
0: Output: CC3 channel is configured as output

OC[3]FE

Bit 2: Output compare 3 fast enable.

OC[3]PE

Bit 3: Output compare 3 preload enable.

Allowed values:
0: Disabled: Preload register on CCR3 disabled. New values written to CCR3 are taken into account immediately
1: Enabled: Preload register on CCR3 enabled. Preload value is loaded into active register on each update event

OC[3]M

Bits 4-6: Output compare 3 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[3]CE

Bit 7: Output compare 3 clear enable.

CC[4]S

Bits 8-9: Capture/Compare 4 selection.

Allowed values:
0: Output: CC3 channel is configured as output

OC[4]FE

Bit 10: Output compare 4 fast enable.

OC[4]PE

Bit 11: Output compare 4 preload enable.

Allowed values:
0: Disabled: Preload register on CCR3 disabled. New values written to CCR3 are taken into account immediately
1: Enabled: Preload register on CCR3 enabled. Preload value is loaded into active register on each update event

OC[4]M

Bits 12-14: Output compare 4 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[4]CE

Bit 15: Output compare 4 clear enable.

OC[3]M_3

Bit 16: Output compare 3 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

OC[4]M_3

Bit 24: Output compare 4 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

CCER

capture/compare enable register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

0/12 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CC[4]NP rw		CC[4]P rw	CC[4]E rw	CC[3]NP rw		CC[3]P rw	CC[3]E rw	CC[2]NP rw		CC[2]P rw	CC[2]E rw	CC[1]NP rw		CC[1]P rw	CC[1]E rw

Toggle fields

CC[1]E

Bit 0: Capture/Compare 1 output enable.

CC[1]P

Bit 1: Capture/Compare 1 output Polarity.

CC[1]NP

Bit 3: Capture/Compare 1 output Polarity.

CC[2]E

Bit 4: Capture/Compare 2 output enable.

CC[2]P

Bit 5: Capture/Compare 2 output Polarity.

CC[2]NP

Bit 7: Capture/Compare 2 output Polarity.

CC[3]E

Bit 8: Capture/Compare 3 output enable.

CC[3]P

Bit 9: Capture/Compare 3 output Polarity.

CC[3]NP

Bit 11: Capture/Compare 3 output Polarity.

CC[4]E

Bit 12: Capture/Compare 4 output enable.

CC[4]P

Bit 13: Capture/Compare 4 output Polarity.

CC[4]NP

Bit 15: Capture/Compare 4 output Polarity.

CNT

counter

Offset: 0x24, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
CNT rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CNT rw

Toggle fields

CNT

Bits 0-31: Low counter value.

Allowed values: 0x0-0xffffffff

PSC

prescaler

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PSC rw

Toggle fields

PSC

Bits 0-15: Prescaler value.

Allowed values: 0x0-0xffff

ARR

auto-reload register

Offset: 0x2c, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ARR rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ARR rw

Toggle fields

ARR

Bits 0-31: Low Auto-reload value.

Allowed values: 0x0-0xffffffff

CCR[1]

capture/compare register

Offset: 0x34, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
CCR rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-31: Capture/Compare value.

Allowed values: 0x0-0xffffffff

CCR[2]

capture/compare register

Offset: 0x38, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
CCR rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-31: Capture/Compare value.

Allowed values: 0x0-0xffffffff

CCR[3]

capture/compare register

Offset: 0x3c, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
CCR rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-31: Capture/Compare value.

Allowed values: 0x0-0xffffffff

CCR[4]

capture/compare register

Offset: 0x40, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
CCR rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-31: Capture/Compare value.

Allowed values: 0x0-0xffffffff

DCR

DMA control register

Offset: 0x48, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			DBL rw								DBA rw

Toggle fields

DBA

Bits 0-4: DMA base address.

Allowed values: 0x0-0x1f

DBL

Bits 8-12: DMA burst length.

Allowed values: 0x0-0x12

DMAR

DMA address for full transfer

Offset: 0x4c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DMAB rw

Toggle fields

DMAB

Bits 0-15: DMA register for burst accesses.

TIM20

0x40015000: Advanced timer

107/168 fields covered.

Toggle register map

Offset	Name	31	30	29	25	24	23	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	CR1																	UIFREMAP		CKD		ARPE	CMS		DIR	OPM	URS	UDIS	CEN
0x4	CR2						MMS2				OIS[6]		OIS[5]		OIS[4]	OIS[3]N	OIS[3]	OIS[2]N	OIS[2]	OIS[1]N	OIS[1]	TI1S	MMS			CCDS	CCUS		CCPC
0x8	SMCR												SMS3	ETP	ECE	ETPS		ETF				MSM	TS			OCCS	SMS
0xc	DIER														TDE	COMDE	CC[4]DE	CC[3]DE	CC[2]DE	CC[1]DE	UDE	BIE	TIE	COMIE	CC[4]IE	CC[3]IE	CC[2]IE	CC[1]IE	UIE
0x10	SR											C6IF	C5IF				CC[4]OF	CC[3]OF	CC[2]OF	CC[1]OF	B2IF	BIF	TIF	COMIF	CC[4]IF	CC[3]IF	CC[2]IF	CC[1]IF	UIF
0x14	EGR																				B2G	BG	TG	COMG	CC[4]G	CC[3]G	CC[2]G	CC[1]G	UG
0x18	CCMR1_Input													IC[2]F				IC[2]PSC		CC[2]S		IC[1]F				IC[1]PSC		CC[1]S
0x18	CCMR1_Output					OC[2]M_3							OC[1]M_3	OC[2]CE	OC[2]M			OC[2]PE	OC[2]FE	CC[2]S		OC[1]CE	OC[1]M			OC[1]PE	OC[1]FE	CC[1]S
0x1c	CCMR2_Input													IC[4]F				IC[4]PSC		CC[4]S		IC[3]F				IC[3]PSC		CC[3]S
0x1c	CCMR2_Output					OC[4]M_3							OC[3]M_3	OC[4]CE	OC[4]M			OC[4]PE	OC[4]FE	CC[4]S		OC[3]CE	OC[3]M			OC[3]PE	OC[3]FE	CC[3]S
0x20	CCER							CC[6]P	CC[6]E			CC[5]P	CC[5]E	CC[4]NP		CC[4]P	CC[4]E	CC[3]NP	CC[3]NE	CC[3]P	CC[3]E	CC[2]NP	CC[2]NE	CC[2]P	CC[2]E	CC[1]NP	CC[1]NE	CC[1]P	CC[1]E
0x24	CNT	UIFCPY												CNT
0x28	PSC													PSC
0x2c	ARR													ARR
0x30	RCR													REP
0x34	CCR[1]													CCR
0x38	CCR[2]													CCR
0x3c	CCR[3]													CCR
0x40	CCR[4]													CCR
0x44	BDTR				BK2P	BK2E	BK2F			BKF				MOE	AOE	BKP	BKE	OSSR	OSSI	LOCK		DTG
0x48	DCR																DBL								DBA
0x4c	DMAR													DMAB
0x54	CCMR3_Output					OC[6]M_3							OC[5]M_3	OC[6]CE	OC[6]M			OC[6]PE	OC[6]FE			OC[5]CE	OC[5]M			OC[5]PE	OC[5]FE
0x58	CCR5	GC5C3	GC5C2	GC5C1										CCR
0x5c	CCR6													CCR
0x60	OR																									TIM1_ETR_ADC4_RMP		TIM1_ETR_ADC1_RMP

Toggle registers

CR1

control register 1

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

8/9 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				UIFREMAP rw		CKD rw		ARPE rw	CMS rw		DIR rw	OPM rw	URS rw	UDIS rw	CEN rw

Toggle fields

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

Allowed values:
0: AnyEvent: Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request
1: CounterOnly: Only counter overflow/underflow generates an update interrupt or DMA request

OPM

Bit 3: One-pulse mode.

Allowed values:
0: Disabled: Counter is not stopped at update event
1: Enabled: Counter stops counting at the next update event (clearing the CEN bit)

DIR

Bit 4: Direction.

Allowed values:
0: Up: Counter used as upcounter
1: Down: Counter used as downcounter

CMS

Bits 5-6: Center-aligned mode selection.

Allowed values:
0: EdgeAligned: The counter counts up or down depending on the direction bit
1: CenterAligned1: The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting down.
2: CenterAligned2: The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting up.
3: CenterAligned3: The counter counts up and down alternatively. Output compare interrupt flags are set both when the counter is counting up or down.

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CKD

Bits 8-9: Clock division.

Allowed values:
0: Div1: t_DTS = t_CK_INT
1: Div2: t_DTS = 2 × t_CK_INT
2: Div4: t_DTS = 4 × t_CK_INT

UIFREMAP

Bit 11: UIF status bit remapping.

CR2

control register 2

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

12/15 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								MMS2 rw					OIS[6] rw		OIS[5] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	OIS[4] rw	OIS[3]N rw	OIS[3] rw	OIS[2]N rw	OIS[2] rw	OIS[1]N rw	OIS[1] rw	TI1S rw	MMS rw			CCDS rw	CCUS rw		CCPC rw

Toggle fields

CCPC

Bit 0: Capture/compare preloaded control.

CCUS

Bit 2: Capture/compare control update selection.

CCDS

Bit 3: Capture/compare DMA selection.

Allowed values:
0: OnCompare: CCx DMA request sent when CCx event occurs
1: OnUpdate: CCx DMA request sent when update event occurs

MMS

Bits 4-6: Master mode selection.

Allowed values:
0: Reset: The UG bit from the TIMx_EGR register is used as trigger output
1: Enable: The counter enable signal, CNT_EN, is used as trigger output
2: Update: The update event is selected as trigger output
3: ComparePulse: The trigger output send a positive pulse when the CC1IF flag it to be set, as soon as a capture or a compare match occurred
4: CompareOC1: OC1REF signal is used as trigger output
5: CompareOC2: OC2REF signal is used as trigger output
6: CompareOC3: OC3REF signal is used as trigger output
7: CompareOC4: OC4REF signal is used as trigger output

TI1S

Bit 7: TI1 selection.

Allowed values:
0: Normal: The TIMx_CH1 pin is connected to TI1 input
1: XOR: The TIMx_CH1, CH2, CH3 pins are connected to TI1 input

OIS[1]

Bit 8: Output Idle state (OC1 output).

Allowed values:
0: Reset: OCx=0 (after a dead-time if OCx(N) is implemented) when MOE=0
1: Set: OCx=1 (after a dead-time if OCx(N) is implemented) when MOE=0

OIS[1]N

Bit 9: Output Idle state (OC1N output).

Allowed values:
0: Reset: OCxN=0 after a dead-time when MOE=0
1: Set: OCxN=1 after a dead-time when MOE=0

OIS[2]

Bit 10: Output Idle state (OC2 output).

Allowed values:
0: Reset: OCx=0 (after a dead-time if OCx(N) is implemented) when MOE=0
1: Set: OCx=1 (after a dead-time if OCx(N) is implemented) when MOE=0

OIS[2]N

Bit 11: Output Idle state (OC2N output).

Allowed values:
0: Reset: OCxN=0 after a dead-time when MOE=0
1: Set: OCxN=1 after a dead-time when MOE=0

OIS[3]

Bit 12: Output Idle state (OC3 output).

Allowed values:
0: Reset: OCx=0 (after a dead-time if OCx(N) is implemented) when MOE=0
1: Set: OCx=1 (after a dead-time if OCx(N) is implemented) when MOE=0

OIS[3]N

Bit 13: Output Idle state (OC3N output).

Allowed values:
0: Reset: OCxN=0 after a dead-time when MOE=0
1: Set: OCxN=1 after a dead-time when MOE=0

OIS[4]

Bit 14: Output Idle state (OC4 output).

Allowed values:
0: Reset: OCx=0 (after a dead-time if OCx(N) is implemented) when MOE=0
1: Set: OCx=1 (after a dead-time if OCx(N) is implemented) when MOE=0

OIS[5]

Bit 16: Output Idle state (OC5 output).

Allowed values:
0: Reset: OCx=0 (after a dead-time if OCx(N) is implemented) when MOE=0
1: Set: OCx=1 (after a dead-time if OCx(N) is implemented) when MOE=0

OIS[6]

Bit 18: Output Idle state (OC6 output).

Allowed values:
0: Reset: OCx=0 (after a dead-time if OCx(N) is implemented) when MOE=0
1: Set: OCx=1 (after a dead-time if OCx(N) is implemented) when MOE=0

MMS2

Bits 20-23: Master mode selection 2.

SMCR

slave mode control register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

7/9 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															SMS3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ETP rw	ECE rw	ETPS rw		ETF rw				MSM rw	TS rw			OCCS rw	SMS rw

Toggle fields

SMS

Bits 0-2: Slave mode selection.

Allowed values:
0: Disabled: Slave mode disabled - if CEN = ‘1 then the prescaler is clocked directly by the internal clock.
1: Encoder_Mode_1: Encoder mode 1 - Counter counts up/down on TI2FP1 edge depending on TI1FP2 level.
2: Encoder_Mode_2: Encoder mode 2 - Counter counts up/down on TI1FP2 edge depending on TI2FP1 level.
3: Encoder_Mode_3: Encoder mode 3 - Counter counts up/down on both TI1FP1 and TI2FP2 edges depending on the level of the other input.
4: Reset_Mode: Reset Mode - Rising edge of the selected trigger input (TRGI) reinitializes the counter and generates an update of the registers.
5: Gated_Mode: Gated Mode - The counter clock is enabled when the trigger input (TRGI) is high. The counter stops (but is not reset) as soon as the trigger becomes low. Both start and stop of the counter are controlled.
6: Trigger_Mode: Trigger Mode - The counter starts at a rising edge of the trigger TRGI (but it is not reset). Only the start of the counter is controlled.
7: Ext_Clock_Mode: External Clock Mode 1 - Rising edges of the selected trigger (TRGI) clock the counter.

OCCS

Bit 3: OCREF clear selection.

TS

Bits 4-6: Trigger selection.

Allowed values:
0: ITR0: Internal Trigger 0 (ITR0)
1: ITR1: Internal Trigger 1 (ITR1)
2: ITR2: Internal Trigger 2 (ITR2)
4: TI1F_ED: TI1 Edge Detector (TI1F_ED)
5: TI1FP1: Filtered Timer Input 1 (TI1FP1)
6: TI2FP2: Filtered Timer Input 2 (TI2FP2)
7: ETRF: External Trigger input (ETRF)

MSM

Bit 7: Master/Slave mode.

Allowed values:
0: NoSync: No action
1: Sync: The effect of an event on the trigger input (TRGI) is delayed to allow a perfect synchronization between the current timer and its slaves (through TRGO). It is useful if we want to synchronize several timers on a single external event.

ETF

Bits 8-11: External trigger filter.

Allowed values:
0: NoFilter: No filter, sampling is done at fDTS
1: FCK_INT_N2: fSAMPLING=fCK_INT, N=2
2: FCK_INT_N4: fSAMPLING=fCK_INT, N=4
3: FCK_INT_N8: fSAMPLING=fCK_INT, N=8
4: FDTS_Div2_N6: fSAMPLING=fDTS/2, N=6
5: FDTS_Div2_N8: fSAMPLING=fDTS/2, N=8
6: FDTS_Div4_N6: fSAMPLING=fDTS/4, N=6
7: FDTS_Div4_N8: fSAMPLING=fDTS/4, N=8
8: FDTS_Div8_N6: fSAMPLING=fDTS/8, N=6
9: FDTS_Div8_N8: fSAMPLING=fDTS/8, N=8
10: FDTS_Div16_N5: fSAMPLING=fDTS/16, N=5
11: FDTS_Div16_N6: fSAMPLING=fDTS/16, N=6
12: FDTS_Div16_N8: fSAMPLING=fDTS/16, N=8
13: FDTS_Div32_N5: fSAMPLING=fDTS/32, N=5
14: FDTS_Div32_N6: fSAMPLING=fDTS/32, N=6
15: FDTS_Div32_N8: fSAMPLING=fDTS/32, N=8

ETPS

Bits 12-13: External trigger prescaler.

Allowed values:
0: Div1: Prescaler OFF
1: Div2: ETRP frequency divided by 2
2: Div4: ETRP frequency divided by 4
3: Div8: ETRP frequency divided by 8

ECE

Bit 14: External clock enable.

Allowed values:
0: Disabled: External clock mode 2 disabled
1: Enabled: External clock mode 2 enabled. The counter is clocked by any active edge on the ETRF signal.

ETP

Bit 15: External trigger polarity.

Allowed values:
0: NotInverted: ETR is noninverted, active at high level or rising edge
1: Inverted: ETR is inverted, active at low level or falling edge

SMS3

Bit 16: Slave mode selection bit 3.

DIER

DMA/Interrupt enable register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

12/15 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	TDE rw	COMDE rw	CC[4]DE rw	CC[3]DE rw	CC[2]DE rw	CC[1]DE rw	UDE rw	BIE rw	TIE rw	COMIE rw	CC[4]IE rw	CC[3]IE rw	CC[2]IE rw	CC[1]IE rw	UIE rw

Toggle fields

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

CC[1]IE

Bit 1: Capture/Compare 1 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC[2]IE

Bit 2: Capture/Compare 2 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC[3]IE

Bit 3: Capture/Compare 3 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC[4]IE

Bit 4: Capture/Compare 4 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

COMIE

Bit 5: COM interrupt enable.

TIE

Bit 6: Trigger interrupt enable.

Allowed values:
0: Disabled: Trigger interrupt disabled
1: Enabled: Trigger interrupt enabled

BIE

Bit 7: Break interrupt enable.

UDE

Bit 8: Update DMA request enable.

Allowed values:
0: Disabled: Update DMA request disabled
1: Enabled: Update DMA request enabled

CC[1]DE

Bit 9: Capture/Compare 1 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC[2]DE

Bit 10: Capture/Compare 2 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC[3]DE

Bit 11: Capture/Compare 3 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC[4]DE

Bit 12: Capture/Compare 4 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

COMDE

Bit 13: COM DMA request enable.

TDE

Bit 14: Trigger DMA request enable.

Allowed values:
0: Disabled: Trigger DMA request disabled
1: Enabled: Trigger DMA request enabled

SR

status register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

10/15 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
														C6IF rw	C5IF rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			CC[4]OF rw	CC[3]OF rw	CC[2]OF rw	CC[1]OF rw	B2IF rw	BIF rw	TIF rw	COMIF rw	CC[4]IF rw	CC[3]IF rw	CC[2]IF rw	CC[1]IF rw	UIF rw

Toggle fields

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: NoUpdateOccurred: No update occurred
1: UpdatePending: Update interrupt pending

CC[1]IF

Bit 1: Capture/compare 1 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC[2]IF

Bit 2: Capture/compare 2 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC[3]IF

Bit 3: Capture/compare 3 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC[4]IF

Bit 4: Capture/compare 4 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

COMIF

Bit 5: COM interrupt flag.

TIF

Bit 6: Trigger interrupt flag.

Allowed values:
0: NoTrigger: No trigger event occurred
1: Trigger: Trigger interrupt pending

BIF

Bit 7: Break interrupt flag.

B2IF

Bit 8: Break 2 interrupt flag.

CC[1]OF

Bit 9: Capture/Compare 1 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC[2]OF

Bit 10: Capture/Compare 2 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC[3]OF

Bit 11: Capture/Compare 3 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC[4]OF

Bit 12: Capture/Compare 4 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

C5IF

Bit 16: Capture/Compare 5 interrupt flag.

C6IF

Bit 17: Capture/Compare 6 interrupt flag.

EGR

event generation register

Offset: 0x14, size: 32, reset: 0x00000000, access: write-only

6/9 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							B2G w	BG w	TG w	COMG w	CC[4]G w	CC[3]G w	CC[2]G w	CC[1]G w	UG w

Toggle fields

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the registers.

CC[1]G

Bit 1: Capture/compare 1 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC[2]G

Bit 2: Capture/compare 2 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC[3]G

Bit 3: Capture/compare 3 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC[4]G

Bit 4: Capture/compare 4 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

COMG

Bit 5: Capture/Compare control update generation.

TG

Bit 6: Trigger generation.

Allowed values:
1: Trigger: The TIF flag is set in TIMx_SR register. Related interrupt or DMA transfer can occur if enabled.

BG

Bit 7: Break generation.

B2G

Bit 8: Break 2 generation.

CCMR1_Input

capture/compare mode register 1 (input mode)

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

4/6 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IC[2]F rw				IC[2]PSC rw		CC[2]S rw		IC[1]F rw				IC[1]PSC rw		CC[1]S rw

Toggle fields

CC[1]S

Bits 0-1: Capture/Compare 1 selection.

Allowed values:
1: TI1: CC1 channel is configured as input, IC1 is mapped on TI1
2: TI2: CC1 channel is configured as input, IC1 is mapped on TI2
3: TRC: CC1 channel is configured as input, IC1 is mapped on TRC

IC[1]PSC

Bits 2-3: Input capture 1 prescaler.

IC[1]F

Bits 4-7: Input capture 1 filter.

Allowed values:
0: NoFilter: No filter, sampling is done at fDTS
1: FCK_INT_N2: fSAMPLING=fCK_INT, N=2
2: FCK_INT_N4: fSAMPLING=fCK_INT, N=4
3: FCK_INT_N8: fSAMPLING=fCK_INT, N=8
4: FDTS_Div2_N6: fSAMPLING=fDTS/2, N=6
5: FDTS_Div2_N8: fSAMPLING=fDTS/2, N=8
6: FDTS_Div4_N6: fSAMPLING=fDTS/4, N=6
7: FDTS_Div4_N8: fSAMPLING=fDTS/4, N=8
8: FDTS_Div8_N6: fSAMPLING=fDTS/8, N=6
9: FDTS_Div8_N8: fSAMPLING=fDTS/8, N=8
10: FDTS_Div16_N5: fSAMPLING=fDTS/16, N=5
11: FDTS_Div16_N6: fSAMPLING=fDTS/16, N=6
12: FDTS_Div16_N8: fSAMPLING=fDTS/16, N=8
13: FDTS_Div32_N5: fSAMPLING=fDTS/32, N=5
14: FDTS_Div32_N6: fSAMPLING=fDTS/32, N=6
15: FDTS_Div32_N8: fSAMPLING=fDTS/32, N=8

CC[2]S

Bits 8-9: Capture/Compare 2 selection.

Allowed values:
1: TI1: CC1 channel is configured as input, IC1 is mapped on TI1
2: TI2: CC1 channel is configured as input, IC1 is mapped on TI2
3: TRC: CC1 channel is configured as input, IC1 is mapped on TRC

IC[2]PSC

Bits 10-11: Input capture 2 prescaler.

IC[2]F

Bits 12-15: Input capture 2 filter.

Allowed values:
0: NoFilter: No filter, sampling is done at fDTS
1: FCK_INT_N2: fSAMPLING=fCK_INT, N=2
2: FCK_INT_N4: fSAMPLING=fCK_INT, N=4
3: FCK_INT_N8: fSAMPLING=fCK_INT, N=8
4: FDTS_Div2_N6: fSAMPLING=fDTS/2, N=6
5: FDTS_Div2_N8: fSAMPLING=fDTS/2, N=8
6: FDTS_Div4_N6: fSAMPLING=fDTS/4, N=6
7: FDTS_Div4_N8: fSAMPLING=fDTS/4, N=8
8: FDTS_Div8_N6: fSAMPLING=fDTS/8, N=6
9: FDTS_Div8_N8: fSAMPLING=fDTS/8, N=8
10: FDTS_Div16_N5: fSAMPLING=fDTS/16, N=5
11: FDTS_Div16_N6: fSAMPLING=fDTS/16, N=6
12: FDTS_Div16_N8: fSAMPLING=fDTS/16, N=8
13: FDTS_Div32_N5: fSAMPLING=fDTS/32, N=5
14: FDTS_Div32_N6: fSAMPLING=fDTS/32, N=6
15: FDTS_Div32_N8: fSAMPLING=fDTS/32, N=8

CCMR1_Output

capture/compare mode register (output mode)

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

8/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
							OC[2]M_3 rw								OC[1]M_3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OC[2]CE rw	OC[2]M rw			OC[2]PE rw	OC[2]FE rw	CC[2]S rw		OC[1]CE rw	OC[1]M rw			OC[1]PE rw	OC[1]FE rw	CC[1]S rw

Toggle fields

CC[1]S

Bits 0-1: Capture/Compare 1 selection.

Allowed values:
0: Output: CC1 channel is configured as output

OC[1]FE

Bit 2: Output compare 1 fast enable.

OC[1]PE

Bit 3: Output compare 1 preload enable.

Allowed values:
0: Disabled: Preload register on CCR1 disabled. New values written to CCR1 are taken into account immediately
1: Enabled: Preload register on CCR1 enabled. Preload value is loaded into active register on each update event

OC[1]M

Bits 4-6: Output compare 1 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[1]CE

Bit 7: Output compare 1 clear enable.

CC[2]S

Bits 8-9: Capture/Compare 2 selection.

Allowed values:
0: Output: CC1 channel is configured as output

OC[2]FE

Bit 10: Output compare 2 fast enable.

OC[2]PE

Bit 11: Output compare 2 preload enable.

Allowed values:
0: Disabled: Preload register on CCR1 disabled. New values written to CCR1 are taken into account immediately
1: Enabled: Preload register on CCR1 enabled. Preload value is loaded into active register on each update event

OC[2]M

Bits 12-14: Output compare 2 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[2]CE

Bit 15: Output compare 2 clear enable.

OC[1]M_3

Bit 16: Output compare 1 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

OC[2]M_3

Bit 24: Output compare 2 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

CCMR2_Input

capture/compare mode register 2 (input mode)

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

6/6 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IC[4]F rw				IC[4]PSC rw		CC[4]S rw		IC[3]F rw				IC[3]PSC rw		CC[3]S rw

Toggle fields

CC[3]S

Bits 0-1: Capture/Compare 3 selection.

Allowed values:
1: TI3: CC3 channel is configured as input, IC3 is mapped on TI3
2: TI4: CC3 channel is configured as input, IC3 is mapped on TI4
3: TRC: CC3 channel is configured as input, IC3 is mapped on TRC

IC[3]PSC

Bits 2-3: Input capture 3 prescaler.

Allowed values: 0x0-0x3

IC[3]F

Bits 4-7: Input capture 3 filter.

Allowed values: 0x0-0xf

CC[4]S

Bits 8-9: Capture/Compare 4 selection.

Allowed values:
1: TI3: CC3 channel is configured as input, IC3 is mapped on TI3
2: TI4: CC3 channel is configured as input, IC3 is mapped on TI4
3: TRC: CC3 channel is configured as input, IC3 is mapped on TRC

IC[4]PSC

Bits 10-11: Input capture 4 prescaler.

Allowed values: 0x0-0x3

IC[4]F

Bits 12-15: Input capture 4 filter.

Allowed values: 0x0-0xf

CCMR2_Output

capture/compare mode register (output mode)

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

8/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
							OC[4]M_3 rw								OC[3]M_3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OC[4]CE rw	OC[4]M rw			OC[4]PE rw	OC[4]FE rw	CC[4]S rw		OC[3]CE rw	OC[3]M rw			OC[3]PE rw	OC[3]FE rw	CC[3]S rw

Toggle fields

CC[3]S

Bits 0-1: Capture/Compare 3 selection.

Allowed values:
0: Output: CC3 channel is configured as output

OC[3]FE

Bit 2: Output compare 3 fast enable.

OC[3]PE

Bit 3: Output compare 3 preload enable.

Allowed values:
0: Disabled: Preload register on CCR3 disabled. New values written to CCR3 are taken into account immediately
1: Enabled: Preload register on CCR3 enabled. Preload value is loaded into active register on each update event

OC[3]M

Bits 4-6: Output compare 3 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[3]CE

Bit 7: Output compare 3 clear enable.

CC[4]S

Bits 8-9: Capture/Compare 4 selection.

Allowed values:
0: Output: CC3 channel is configured as output

OC[4]FE

Bit 10: Output compare 4 fast enable.

OC[4]PE

Bit 11: Output compare 4 preload enable.

Allowed values:
0: Disabled: Preload register on CCR3 disabled. New values written to CCR3 are taken into account immediately
1: Enabled: Preload register on CCR3 enabled. Preload value is loaded into active register on each update event

OC[4]M

Bits 12-14: Output compare 4 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[4]CE

Bit 15: Output compare 4 clear enable.

OC[3]M_3

Bit 16: Output compare 3 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

OC[4]M_3

Bit 24: Output compare 4 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

CCER

capture/compare enable register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

0/19 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
										CC[6]P rw	CC[6]E rw			CC[5]P rw	CC[5]E rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CC[4]NP rw		CC[4]P rw	CC[4]E rw	CC[3]NP rw	CC[3]NE rw	CC[3]P rw	CC[3]E rw	CC[2]NP rw	CC[2]NE rw	CC[2]P rw	CC[2]E rw	CC[1]NP rw	CC[1]NE rw	CC[1]P rw	CC[1]E rw

Toggle fields

CC[1]E

Bit 0: Capture/Compare 1 output enable.

CC[1]P

Bit 1: Capture/Compare 1 output Polarity.

CC[1]NE

Bit 2: Capture/Compare 1 complementary output enable.

CC[1]NP

Bit 3: Capture/Compare 1 output Polarity.

CC[2]E

Bit 4: Capture/Compare 2 output enable.

CC[2]P

Bit 5: Capture/Compare 2 output Polarity.

CC[2]NE

Bit 6: Capture/Compare 2 complementary output enable.

CC[2]NP

Bit 7: Capture/Compare 2 output Polarity.

CC[3]E

Bit 8: Capture/Compare 3 output enable.

CC[3]P

Bit 9: Capture/Compare 3 output Polarity.

CC[3]NE

Bit 10: Capture/Compare 3 complementary output enable.

CC[3]NP

Bit 11: Capture/Compare 3 output Polarity.

CC[4]E

Bit 12: Capture/Compare 4 output enable.

CC[4]P

Bit 13: Capture/Compare 4 output Polarity.

CC[4]NP

Bit 15: Capture/Compare 4 output Polarity.

CC[5]E

Bit 16: Capture/Compare 5 output enable.

CC[5]P

Bit 17: Capture/Compare 5 output Polarity.

CC[6]E

Bit 20: Capture/Compare 6 output enable.

CC[6]P

Bit 21: Capture/Compare 6 output Polarity.

CNT

counter

Offset: 0x24, size: 32, reset: 0x00000000, access: Unspecified

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
UIFCPY r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CNT rw

Toggle fields

CNT

Bits 0-15: counter value.

Allowed values: 0x0-0xffff

UIFCPY

Bit 31: UIF copy.

PSC

prescaler

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PSC rw

Toggle fields

PSC

Bits 0-15: Prescaler value.

Allowed values: 0x0-0xffff

ARR

auto-reload register

Offset: 0x2c, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ARR rw

Toggle fields

ARR

Bits 0-15: Auto-reload value.

Allowed values: 0x0-0xffff

RCR

repetition counter register

Offset: 0x30, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
REP rw

Toggle fields

REP

Bits 0-15: Repetition counter value.

CCR[1]

capture/compare register

Offset: 0x34, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

Allowed values: 0x0-0xffff

CCR[2]

capture/compare register

Offset: 0x38, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

Allowed values: 0x0-0xffff

CCR[3]

capture/compare register

Offset: 0x3c, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

Allowed values: 0x0-0xffff

CCR[4]

capture/compare register

Offset: 0x40, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

Allowed values: 0x0-0xffff

BDTR

break and dead-time register

Offset: 0x44, size: 32, reset: 0x00000000, access: read-write

10/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
						BK2P rw	BK2E rw	BK2F rw				BKF rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MOE rw	AOE rw	BKP rw	BKE rw	OSSR rw	OSSI rw	LOCK rw		DTG rw

Toggle fields

DTG

Bits 0-7: Dead-time generator setup.

Allowed values: 0x0-0xff

LOCK

Bits 8-9: Lock configuration.

Allowed values:
0: Off: No bit is write protected
1: Level1: Any bits except MOE, OSSR, OSSI and LOCK in TIMx_BDTR register, OISx and OISxN bits in TIMx_CR2 register can no longer be written
2: Level2: LOCK Level 1 + CC Polarity bits (CCxP/CCxNP bits in TIMx_CCER register, as long as the related channel is configured in output through the CCxS bits) as well as OSSR and OSSI bits can no longer be written
3: Level3: LOCK Level 2 + CC Control bits (OCxM and OCxPE bits in TIMx_CCMRx registers, as long as the related channel is configured in output through the CCxS bits) can no longer be written

OSSI

Bit 10: Off-state selection for Idle mode.

Allowed values:
0: Disabled: When inactive, OC/OCN outputs are disabled
1: IdleLevel: When inactive, OC/OCN outputs are forced to idle level

OSSR

Bit 11: Off-state selection for Run mode.

Allowed values:
0: Disabled: When inactive, OC/OCN outputs are disabled
1: IdleLevel: When inactive, OC/OCN outputs are enabled with their inactive level

BKE

Bit 12: Break enable.

Allowed values:
0: Disabled: Break function x disabled
1: Enabled: Break function x disabled

BKP

Bit 13: Break polarity.

Allowed values:
0: ActiveLow: Break input BRKx is active low
1: ActiveHigh: Break input BRKx is active high

AOE

Bit 14: Automatic output enable.

Allowed values:
0: Manual: MOE can be set only by software
1: Automatic: MOE can be set by software or automatically at the next update event (if none of the break inputs BRK and BRK2 is active)

MOE

Bit 15: Main output enable.

Allowed values:
0: DisabledIdle: OC/OCN are disabled or forced idle depending on OSSI
1: Enabled: OC/OCN are enabled if CCxE/CCxNE are set

BKF

Bits 16-19: Break filter.

BK2F

Bits 20-23: Break 2 filter.

BK2E

Bit 24: Break 2 enable.

Allowed values:
0: Disabled: Break function x disabled
1: Enabled: Break function x disabled

BK2P

Bit 25: Break 2 polarity.

Allowed values:
0: ActiveLow: Break input BRKx is active low
1: ActiveHigh: Break input BRKx is active high

DCR

DMA control register

Offset: 0x48, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			DBL rw								DBA rw

Toggle fields

DBA

Bits 0-4: DMA base address.

Allowed values: 0x0-0x1f

DBL

Bits 8-12: DMA burst length.

Allowed values: 0x0-0x12

DMAR

DMA address for full transfer

Offset: 0x4c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DMAB rw

Toggle fields

DMAB

Bits 0-15: DMA register for burst accesses.

CCMR3_Output

capture/compare mode register 3 (output mode)

Offset: 0x54, size: 32, reset: 0x00000000, access: read-write

4/10 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
							OC[6]M_3 rw								OC[5]M_3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OC[6]CE rw	OC[6]M rw			OC[6]PE rw	OC[6]FE rw			OC[5]CE rw	OC[5]M rw			OC[5]PE rw	OC[5]FE rw

Toggle fields

OC[5]FE

Bit 2: Output compare 5 fast enable.

OC[5]PE

Bit 3: Output compare 5 preload enable.

OC[5]M

Bits 4-6: Output compare 5 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[5]CE

Bit 7: Output compare 5 clear enable.

OC[6]FE

Bit 10: Output compare 6 fast enable.

OC[6]PE

Bit 11: Output compare 6 preload enable.

OC[6]M

Bits 12-14: Output compare 6 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[6]CE

Bit 15: Output compare 6 clear enable.

OC[5]M_3

Bit 16: Output compare 5 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

OC[6]M_3

Bit 24: Output compare 6 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

CCR5

capture/compare register

Offset: 0x58, size: 32, reset: 0x00000000, access: read-write

1/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
GC5C3 rw	GC5C2 rw	GC5C1 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

Allowed values: 0x0-0xffff

GC5C1

Bit 29: Group Channel 5 and Channel 1.

GC5C2

Bit 30: Group Channel 5 and Channel 2.

GC5C3

Bit 31: Group Channel 5 and Channel 3.

CCR6

capture/compare register

Offset: 0x5c, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

Allowed values: 0x0-0xffff

OR

option registers

Offset: 0x60, size: 32, reset: 0x00000000, access: read-write

0/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
												TIM1_ETR_ADC4_RMP rw		TIM1_ETR_ADC1_RMP rw

Toggle fields

TIM1_ETR_ADC1_RMP

Bits 0-1: TIM1_ETR_ADC1 remapping capability.

TIM1_ETR_ADC4_RMP

Bits 2-3: TIM1_ETR_ADC4 remapping capability.

TIM3

0x40000400: General purpose timer

81/108 fields covered.

Toggle register map

Offset	Name	31	24	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	CR1								UIFREMAP		CKD		ARPE	CMS		DIR	OPM	URS	UDIS	CEN
0x4	CR2												TI1S	MMS			CCDS
0x8	SMCR			SMS_3	ETP	ECE	ETPS		ETF				MSM	TS			OCCS	SMS
0xc	DIER					TDE		CC[4]DE	CC[3]DE	CC[2]DE	CC[1]DE	UDE		TIE		CC[4]IE	CC[3]IE	CC[2]IE	CC[1]IE	UIE
0x10	SR							CC[4]OF	CC[3]OF	CC[2]OF	CC[1]OF			TIF		CC[4]IF	CC[3]IF	CC[2]IF	CC[1]IF	UIF
0x14	EGR													TG		CC[4]G	CC[3]G	CC[2]G	CC[1]G	UG
0x18	CCMR1_Input				IC[2]F				IC[2]PSC		CC[2]S		IC[1]F				IC[1]PSC		CC[1]S
0x18	CCMR1_Output		OC[2]M_3	OC[1]M_3	OC[2]CE	OC[2]M			OC[2]PE	OC[2]FE	CC[2]S		OC[1]CE	OC[1]M			OC[1]PE	OC[1]FE	CC[1]S
0x1c	CCMR2_Input				IC[4]F				IC[4]PSC		CC[4]S		IC[3]F				IC[3]PSC		CC[3]S
0x1c	CCMR2_Output		OC[4]M_3	OC[3]M_3	OC[4]CE	OC[4]M			OC[4]PE	OC[4]FE	CC[4]S		OC[3]CE	OC[3]M			OC[3]PE	OC[3]FE	CC[3]S
0x20	CCER				CC[4]NP		CC[4]P	CC[4]E	CC[3]NP		CC[3]P	CC[3]E	CC[2]NP		CC[2]P	CC[2]E	CC[1]NP		CC[1]P	CC[1]E
0x24	CNT	UIFCPY			CNT
0x28	PSC				PSC
0x2c	ARR				ARR
0x34	CCR[1]				CCR
0x38	CCR[2]				CCR
0x3c	CCR[3]				CCR
0x40	CCR[4]				CCR
0x48	DCR							DBL								DBA
0x4c	DMAR				DMAB

Toggle registers

CR1

control register 1

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

8/9 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				UIFREMAP rw		CKD rw		ARPE rw	CMS rw		DIR rw	OPM rw	URS rw	UDIS rw	CEN rw

Toggle fields

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

Allowed values:
0: AnyEvent: Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request
1: CounterOnly: Only counter overflow/underflow generates an update interrupt or DMA request

OPM

Bit 3: One-pulse mode.

Allowed values:
0: Disabled: Counter is not stopped at update event
1: Enabled: Counter stops counting at the next update event (clearing the CEN bit)

DIR

Bit 4: Direction.

Allowed values:
0: Up: Counter used as upcounter
1: Down: Counter used as downcounter

CMS

Bits 5-6: Center-aligned mode selection.

Allowed values:
0: EdgeAligned: The counter counts up or down depending on the direction bit
1: CenterAligned1: The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting down.
2: CenterAligned2: The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting up.
3: CenterAligned3: The counter counts up and down alternatively. Output compare interrupt flags are set both when the counter is counting up or down.

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CKD

Bits 8-9: Clock division.

Allowed values:
0: Div1: t_DTS = t_CK_INT
1: Div2: t_DTS = 2 × t_CK_INT
2: Div4: t_DTS = 4 × t_CK_INT

UIFREMAP

Bit 11: UIF status bit remapping.

CR2

control register 2

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

3/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								TI1S rw	MMS rw			CCDS rw

Toggle fields

CCDS

Bit 3: Capture/compare DMA selection.

Allowed values:
0: OnCompare: CCx DMA request sent when CCx event occurs
1: OnUpdate: CCx DMA request sent when update event occurs

MMS

Bits 4-6: Master mode selection.

Allowed values:
0: Reset: The UG bit from the TIMx_EGR register is used as trigger output
1: Enable: The counter enable signal, CNT_EN, is used as trigger output
2: Update: The update event is selected as trigger output
3: ComparePulse: The trigger output send a positive pulse when the CC1IF flag it to be set, as soon as a capture or a compare match occurred
4: CompareOC1: OC1REF signal is used as trigger output
5: CompareOC2: OC2REF signal is used as trigger output
6: CompareOC3: OC3REF signal is used as trigger output
7: CompareOC4: OC4REF signal is used as trigger output

TI1S

Bit 7: TI1 selection.

Allowed values:
0: Normal: The TIMx_CH1 pin is connected to TI1 input
1: XOR: The TIMx_CH1, CH2, CH3 pins are connected to TI1 input

SMCR

slave mode control register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

7/9 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															SMS_3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ETP rw	ECE rw	ETPS rw		ETF rw				MSM rw	TS rw			OCCS rw	SMS rw

Toggle fields

SMS

Bits 0-2: Slave mode selection.

Allowed values:
0: Disabled: Slave mode disabled - if CEN = ‘1 then the prescaler is clocked directly by the internal clock.
1: Encoder_Mode_1: Encoder mode 1 - Counter counts up/down on TI2FP1 edge depending on TI1FP2 level.
2: Encoder_Mode_2: Encoder mode 2 - Counter counts up/down on TI1FP2 edge depending on TI2FP1 level.
3: Encoder_Mode_3: Encoder mode 3 - Counter counts up/down on both TI1FP1 and TI2FP2 edges depending on the level of the other input.
4: Reset_Mode: Reset Mode - Rising edge of the selected trigger input (TRGI) reinitializes the counter and generates an update of the registers.
5: Gated_Mode: Gated Mode - The counter clock is enabled when the trigger input (TRGI) is high. The counter stops (but is not reset) as soon as the trigger becomes low. Both start and stop of the counter are controlled.
6: Trigger_Mode: Trigger Mode - The counter starts at a rising edge of the trigger TRGI (but it is not reset). Only the start of the counter is controlled.
7: Ext_Clock_Mode: External Clock Mode 1 - Rising edges of the selected trigger (TRGI) clock the counter.

OCCS

Bit 3: OCREF clear selection.

TS

Bits 4-6: Trigger selection.

Allowed values:
0: ITR0: Internal Trigger 0 (ITR0)
1: ITR1: Internal Trigger 1 (ITR1)
2: ITR2: Internal Trigger 2 (ITR2)
4: TI1F_ED: TI1 Edge Detector (TI1F_ED)
5: TI1FP1: Filtered Timer Input 1 (TI1FP1)
6: TI2FP2: Filtered Timer Input 2 (TI2FP2)
7: ETRF: External Trigger input (ETRF)

MSM

Bit 7: Master/Slave mode.

Allowed values:
0: NoSync: No action
1: Sync: The effect of an event on the trigger input (TRGI) is delayed to allow a perfect synchronization between the current timer and its slaves (through TRGO). It is useful if we want to synchronize several timers on a single external event.

ETF

Bits 8-11: External trigger filter.

Allowed values:
0: NoFilter: No filter, sampling is done at fDTS
1: FCK_INT_N2: fSAMPLING=fCK_INT, N=2
2: FCK_INT_N4: fSAMPLING=fCK_INT, N=4
3: FCK_INT_N8: fSAMPLING=fCK_INT, N=8
4: FDTS_Div2_N6: fSAMPLING=fDTS/2, N=6
5: FDTS_Div2_N8: fSAMPLING=fDTS/2, N=8
6: FDTS_Div4_N6: fSAMPLING=fDTS/4, N=6
7: FDTS_Div4_N8: fSAMPLING=fDTS/4, N=8
8: FDTS_Div8_N6: fSAMPLING=fDTS/8, N=6
9: FDTS_Div8_N8: fSAMPLING=fDTS/8, N=8
10: FDTS_Div16_N5: fSAMPLING=fDTS/16, N=5
11: FDTS_Div16_N6: fSAMPLING=fDTS/16, N=6
12: FDTS_Div16_N8: fSAMPLING=fDTS/16, N=8
13: FDTS_Div32_N5: fSAMPLING=fDTS/32, N=5
14: FDTS_Div32_N6: fSAMPLING=fDTS/32, N=6
15: FDTS_Div32_N8: fSAMPLING=fDTS/32, N=8

ETPS

Bits 12-13: External trigger prescaler.

Allowed values:
0: Div1: Prescaler OFF
1: Div2: ETRP frequency divided by 2
2: Div4: ETRP frequency divided by 4
3: Div8: ETRP frequency divided by 8

ECE

Bit 14: External clock enable.

Allowed values:
0: Disabled: External clock mode 2 disabled
1: Enabled: External clock mode 2 enabled. The counter is clocked by any active edge on the ETRF signal.

ETP

Bit 15: External trigger polarity.

Allowed values:
0: NotInverted: ETR is noninverted, active at high level or rising edge
1: Inverted: ETR is inverted, active at low level or falling edge

SMS_3

Bit 16: Slave mode selection bit3.

DIER

DMA/Interrupt enable register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

12/12 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	TDE rw		CC[4]DE rw	CC[3]DE rw	CC[2]DE rw	CC[1]DE rw	UDE rw		TIE rw		CC[4]IE rw	CC[3]IE rw	CC[2]IE rw	CC[1]IE rw	UIE rw

Toggle fields

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

CC[1]IE

Bit 1: Capture/Compare 1 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC[2]IE

Bit 2: Capture/Compare 2 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC[3]IE

Bit 3: Capture/Compare 3 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC[4]IE

Bit 4: Capture/Compare 4 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

TIE

Bit 6: Trigger interrupt enable.

Allowed values:
0: Disabled: Trigger interrupt disabled
1: Enabled: Trigger interrupt enabled

UDE

Bit 8: Update DMA request enable.

Allowed values:
0: Disabled: Update DMA request disabled
1: Enabled: Update DMA request enabled

CC[1]DE

Bit 9: Capture/Compare 1 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC[2]DE

Bit 10: Capture/Compare 2 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC[3]DE

Bit 11: Capture/Compare 3 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC[4]DE

Bit 12: Capture/Compare 4 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

TDE

Bit 14: Trigger DMA request enable.

Allowed values:
0: Disabled: Trigger DMA request disabled
1: Enabled: Trigger DMA request enabled

SR

status register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

10/10 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			CC[4]OF rw	CC[3]OF rw	CC[2]OF rw	CC[1]OF rw			TIF rw		CC[4]IF rw	CC[3]IF rw	CC[2]IF rw	CC[1]IF rw	UIF rw

Toggle fields

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: NoUpdateOccurred: No update occurred
1: UpdatePending: Update interrupt pending

CC[1]IF

Bit 1: Capture/compare 1 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC[2]IF

Bit 2: Capture/compare 2 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC[3]IF

Bit 3: Capture/compare 3 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC[4]IF

Bit 4: Capture/compare 4 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

TIF

Bit 6: Trigger interrupt flag.

Allowed values:
0: NoTrigger: No trigger event occurred
1: Trigger: Trigger interrupt pending

CC[1]OF

Bit 9: Capture/Compare 1 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC[2]OF

Bit 10: Capture/Compare 2 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC[3]OF

Bit 11: Capture/Compare 3 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC[4]OF

Bit 12: Capture/Compare 4 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

EGR

event generation register

Offset: 0x14, size: 32, reset: 0x00000000, access: write-only

6/6 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
									TG w		CC[4]G w	CC[3]G w	CC[2]G w	CC[1]G w	UG w

Toggle fields

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the registers.

CC[1]G

Bit 1: Capture/compare 1 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC[2]G

Bit 2: Capture/compare 2 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC[3]G

Bit 3: Capture/compare 3 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC[4]G

Bit 4: Capture/compare 4 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

TG

Bit 6: Trigger generation.

Allowed values:
1: Trigger: The TIF flag is set in TIMx_SR register. Related interrupt or DMA transfer can occur if enabled.

CCMR1_Input

capture/compare mode register 1 (input mode)

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

4/6 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IC[2]F rw				IC[2]PSC rw		CC[2]S rw		IC[1]F rw				IC[1]PSC rw		CC[1]S rw

Toggle fields

CC[1]S

Bits 0-1: Capture/Compare 1 selection.

Allowed values:
1: TI1: CC1 channel is configured as input, IC1 is mapped on TI1
2: TI2: CC1 channel is configured as input, IC1 is mapped on TI2
3: TRC: CC1 channel is configured as input, IC1 is mapped on TRC

IC[1]PSC

Bits 2-3: Input capture 1 prescaler.

IC[1]F

Bits 4-7: Input capture 1 filter.

Allowed values:
0: NoFilter: No filter, sampling is done at fDTS
1: FCK_INT_N2: fSAMPLING=fCK_INT, N=2
2: FCK_INT_N4: fSAMPLING=fCK_INT, N=4
3: FCK_INT_N8: fSAMPLING=fCK_INT, N=8
4: FDTS_Div2_N6: fSAMPLING=fDTS/2, N=6
5: FDTS_Div2_N8: fSAMPLING=fDTS/2, N=8
6: FDTS_Div4_N6: fSAMPLING=fDTS/4, N=6
7: FDTS_Div4_N8: fSAMPLING=fDTS/4, N=8
8: FDTS_Div8_N6: fSAMPLING=fDTS/8, N=6
9: FDTS_Div8_N8: fSAMPLING=fDTS/8, N=8
10: FDTS_Div16_N5: fSAMPLING=fDTS/16, N=5
11: FDTS_Div16_N6: fSAMPLING=fDTS/16, N=6
12: FDTS_Div16_N8: fSAMPLING=fDTS/16, N=8
13: FDTS_Div32_N5: fSAMPLING=fDTS/32, N=5
14: FDTS_Div32_N6: fSAMPLING=fDTS/32, N=6
15: FDTS_Div32_N8: fSAMPLING=fDTS/32, N=8

CC[2]S

Bits 8-9: Capture/Compare 2 selection.

Allowed values:
1: TI1: CC1 channel is configured as input, IC1 is mapped on TI1
2: TI2: CC1 channel is configured as input, IC1 is mapped on TI2
3: TRC: CC1 channel is configured as input, IC1 is mapped on TRC

IC[2]PSC

Bits 10-11: Input capture 2 prescaler.

IC[2]F

Bits 12-15: Input capture 2 filter.

Allowed values:
0: NoFilter: No filter, sampling is done at fDTS
1: FCK_INT_N2: fSAMPLING=fCK_INT, N=2
2: FCK_INT_N4: fSAMPLING=fCK_INT, N=4
3: FCK_INT_N8: fSAMPLING=fCK_INT, N=8
4: FDTS_Div2_N6: fSAMPLING=fDTS/2, N=6
5: FDTS_Div2_N8: fSAMPLING=fDTS/2, N=8
6: FDTS_Div4_N6: fSAMPLING=fDTS/4, N=6
7: FDTS_Div4_N8: fSAMPLING=fDTS/4, N=8
8: FDTS_Div8_N6: fSAMPLING=fDTS/8, N=6
9: FDTS_Div8_N8: fSAMPLING=fDTS/8, N=8
10: FDTS_Div16_N5: fSAMPLING=fDTS/16, N=5
11: FDTS_Div16_N6: fSAMPLING=fDTS/16, N=6
12: FDTS_Div16_N8: fSAMPLING=fDTS/16, N=8
13: FDTS_Div32_N5: fSAMPLING=fDTS/32, N=5
14: FDTS_Div32_N6: fSAMPLING=fDTS/32, N=6
15: FDTS_Div32_N8: fSAMPLING=fDTS/32, N=8

CCMR1_Output

capture/compare mode register 1 (output mode)

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

8/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
							OC[2]M_3 rw								OC[1]M_3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OC[2]CE rw	OC[2]M rw			OC[2]PE rw	OC[2]FE rw	CC[2]S rw		OC[1]CE rw	OC[1]M rw			OC[1]PE rw	OC[1]FE rw	CC[1]S rw

Toggle fields

CC[1]S

Bits 0-1: Capture/Compare 1 selection.

Allowed values:
0: Output: CC1 channel is configured as output

OC[1]FE

Bit 2: Output compare 1 fast enable.

OC[1]PE

Bit 3: Output compare 1 preload enable.

Allowed values:
0: Disabled: Preload register on CCR1 disabled. New values written to CCR1 are taken into account immediately
1: Enabled: Preload register on CCR1 enabled. Preload value is loaded into active register on each update event

OC[1]M

Bits 4-6: Output compare 1 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[1]CE

Bit 7: Output compare 1 clear enable.

CC[2]S

Bits 8-9: Capture/Compare 2 selection.

Allowed values:
0: Output: CC1 channel is configured as output

OC[2]FE

Bit 10: Output compare 2 fast enable.

OC[2]PE

Bit 11: Output compare 2 preload enable.

Allowed values:
0: Disabled: Preload register on CCR1 disabled. New values written to CCR1 are taken into account immediately
1: Enabled: Preload register on CCR1 enabled. Preload value is loaded into active register on each update event

OC[2]M

Bits 12-14: Output compare 2 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[2]CE

Bit 15: Output compare 2 clear enable.

OC[1]M_3

Bit 16: Output compare 1 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

OC[2]M_3

Bit 24: Output compare 2 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

CCMR2_Input

capture/compare mode register 2 (input mode)

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

6/6 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IC[4]F rw				IC[4]PSC rw		CC[4]S rw		IC[3]F rw				IC[3]PSC rw		CC[3]S rw

Toggle fields

CC[3]S

Bits 0-1: Capture/Compare 3 selection.

Allowed values:
1: TI3: CC3 channel is configured as input, IC3 is mapped on TI3
2: TI4: CC3 channel is configured as input, IC3 is mapped on TI4
3: TRC: CC3 channel is configured as input, IC3 is mapped on TRC

IC[3]PSC

Bits 2-3: Input capture 3 prescaler.

Allowed values: 0x0-0x3

IC[3]F

Bits 4-7: Input capture 3 filter.

Allowed values: 0x0-0xf

CC[4]S

Bits 8-9: Capture/Compare 4 selection.

Allowed values:
1: TI3: CC3 channel is configured as input, IC3 is mapped on TI3
2: TI4: CC3 channel is configured as input, IC3 is mapped on TI4
3: TRC: CC3 channel is configured as input, IC3 is mapped on TRC

IC[4]PSC

Bits 10-11: Input capture 4 prescaler.

Allowed values: 0x0-0x3

IC[4]F

Bits 12-15: Input capture 4 filter.

Allowed values: 0x0-0xf

CCMR2_Output

capture/compare mode register 2 (output mode)

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

8/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
							OC[4]M_3 rw								OC[3]M_3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OC[4]CE rw	OC[4]M rw			OC[4]PE rw	OC[4]FE rw	CC[4]S rw		OC[3]CE rw	OC[3]M rw			OC[3]PE rw	OC[3]FE rw	CC[3]S rw

Toggle fields

CC[3]S

Bits 0-1: Capture/Compare 3 selection.

Allowed values:
0: Output: CC3 channel is configured as output

OC[3]FE

Bit 2: Output compare 3 fast enable.

OC[3]PE

Bit 3: Output compare 3 preload enable.

Allowed values:
0: Disabled: Preload register on CCR3 disabled. New values written to CCR3 are taken into account immediately
1: Enabled: Preload register on CCR3 enabled. Preload value is loaded into active register on each update event

OC[3]M

Bits 4-6: Output compare 3 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[3]CE

Bit 7: Output compare 3 clear enable.

CC[4]S

Bits 8-9: Capture/Compare 4 selection.

Allowed values:
0: Output: CC3 channel is configured as output

OC[4]FE

Bit 10: Output compare 4 fast enable.

OC[4]PE

Bit 11: Output compare 4 preload enable.

Allowed values:
0: Disabled: Preload register on CCR3 disabled. New values written to CCR3 are taken into account immediately
1: Enabled: Preload register on CCR3 enabled. Preload value is loaded into active register on each update event

OC[4]M

Bits 12-14: Output compare 4 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[4]CE

Bit 15: Output compare 4 clear enable.

OC[3]M_3

Bit 16: Output compare 3 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

OC[4]M_3

Bit 24: Output compare 4 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

CCER

capture/compare enable register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

0/12 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CC[4]NP rw		CC[4]P rw	CC[4]E rw	CC[3]NP rw		CC[3]P rw	CC[3]E rw	CC[2]NP rw		CC[2]P rw	CC[2]E rw	CC[1]NP rw		CC[1]P rw	CC[1]E rw

Toggle fields

CC[1]E

Bit 0: Capture/Compare 1 output enable.

CC[1]P

Bit 1: Capture/Compare 1 output Polarity.

CC[1]NP

Bit 3: Capture/Compare 1 output Polarity.

CC[2]E

Bit 4: Capture/Compare 2 output enable.

CC[2]P

Bit 5: Capture/Compare 2 output Polarity.

CC[2]NP

Bit 7: Capture/Compare 2 output Polarity.

CC[3]E

Bit 8: Capture/Compare 3 output enable.

CC[3]P

Bit 9: Capture/Compare 3 output Polarity.

CC[3]NP

Bit 11: Capture/Compare 3 output Polarity.

CC[4]E

Bit 12: Capture/Compare 4 output enable.

CC[4]P

Bit 13: Capture/Compare 4 output Polarity.

CC[4]NP

Bit 15: Capture/Compare 4 output Polarity.

CNT

counter

Offset: 0x24, size: 32, reset: 0x00000000, access: read-write

1/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
UIFCPY rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CNT rw

Toggle fields

CNT

Bits 0-15: Counter value.

Allowed values: 0x0-0xffff

UIFCPY

Bit 31: if IUFREMAP=0 than CNT with read write access else UIFCPY with read only access.

PSC

prescaler

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PSC rw

Toggle fields

PSC

Bits 0-15: Prescaler value.

Allowed values: 0x0-0xffff

ARR

auto-reload register

Offset: 0x2c, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ARR rw

Toggle fields

ARR

Bits 0-15: Auto-reload value.

Allowed values: 0x0-0xffff

CCR[1]

capture/compare register

Offset: 0x34, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

Allowed values: 0x0-0xffff

CCR[2]

capture/compare register

Offset: 0x38, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

Allowed values: 0x0-0xffff

CCR[3]

capture/compare register

Offset: 0x3c, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

Allowed values: 0x0-0xffff

CCR[4]

capture/compare register

Offset: 0x40, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

Allowed values: 0x0-0xffff

DCR

DMA control register

Offset: 0x48, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			DBL rw								DBA rw

Toggle fields

DBA

Bits 0-4: DMA base address.

Allowed values: 0x0-0x1f

DBL

Bits 8-12: DMA burst length.

Allowed values: 0x0-0x12

DMAR

DMA address for full transfer

Offset: 0x4c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DMAB rw

Toggle fields

DMAB

Bits 0-15: DMA register for burst accesses.

TIM4

0x40000800: General purpose timer

81/108 fields covered.

Toggle register map

Offset	Name	31	24	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	CR1								UIFREMAP		CKD		ARPE	CMS		DIR	OPM	URS	UDIS	CEN
0x4	CR2												TI1S	MMS			CCDS
0x8	SMCR			SMS_3	ETP	ECE	ETPS		ETF				MSM	TS			OCCS	SMS
0xc	DIER					TDE		CC[4]DE	CC[3]DE	CC[2]DE	CC[1]DE	UDE		TIE		CC[4]IE	CC[3]IE	CC[2]IE	CC[1]IE	UIE
0x10	SR							CC[4]OF	CC[3]OF	CC[2]OF	CC[1]OF			TIF		CC[4]IF	CC[3]IF	CC[2]IF	CC[1]IF	UIF
0x14	EGR													TG		CC[4]G	CC[3]G	CC[2]G	CC[1]G	UG
0x18	CCMR1_Input				IC[2]F				IC[2]PSC		CC[2]S		IC[1]F				IC[1]PSC		CC[1]S
0x18	CCMR1_Output		OC[2]M_3	OC[1]M_3	OC[2]CE	OC[2]M			OC[2]PE	OC[2]FE	CC[2]S		OC[1]CE	OC[1]M			OC[1]PE	OC[1]FE	CC[1]S
0x1c	CCMR2_Input				IC[4]F				IC[4]PSC		CC[4]S		IC[3]F				IC[3]PSC		CC[3]S
0x1c	CCMR2_Output		OC[4]M_3	OC[3]M_3	OC[4]CE	OC[4]M			OC[4]PE	OC[4]FE	CC[4]S		OC[3]CE	OC[3]M			OC[3]PE	OC[3]FE	CC[3]S
0x20	CCER				CC[4]NP		CC[4]P	CC[4]E	CC[3]NP		CC[3]P	CC[3]E	CC[2]NP		CC[2]P	CC[2]E	CC[1]NP		CC[1]P	CC[1]E
0x24	CNT	UIFCPY			CNT
0x28	PSC				PSC
0x2c	ARR				ARR
0x34	CCR[1]				CCR
0x38	CCR[2]				CCR
0x3c	CCR[3]				CCR
0x40	CCR[4]				CCR
0x48	DCR							DBL								DBA
0x4c	DMAR				DMAB

Toggle registers

CR1

control register 1

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

8/9 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				UIFREMAP rw		CKD rw		ARPE rw	CMS rw		DIR rw	OPM rw	URS rw	UDIS rw	CEN rw

Toggle fields

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

Allowed values:
0: AnyEvent: Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request
1: CounterOnly: Only counter overflow/underflow generates an update interrupt or DMA request

OPM

Bit 3: One-pulse mode.

Allowed values:
0: Disabled: Counter is not stopped at update event
1: Enabled: Counter stops counting at the next update event (clearing the CEN bit)

DIR

Bit 4: Direction.

Allowed values:
0: Up: Counter used as upcounter
1: Down: Counter used as downcounter

CMS

Bits 5-6: Center-aligned mode selection.

Allowed values:
0: EdgeAligned: The counter counts up or down depending on the direction bit
1: CenterAligned1: The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting down.
2: CenterAligned2: The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting up.
3: CenterAligned3: The counter counts up and down alternatively. Output compare interrupt flags are set both when the counter is counting up or down.

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CKD

Bits 8-9: Clock division.

Allowed values:
0: Div1: t_DTS = t_CK_INT
1: Div2: t_DTS = 2 × t_CK_INT
2: Div4: t_DTS = 4 × t_CK_INT

UIFREMAP

Bit 11: UIF status bit remapping.

CR2

control register 2

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

3/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								TI1S rw	MMS rw			CCDS rw

Toggle fields

CCDS

Bit 3: Capture/compare DMA selection.

Allowed values:
0: OnCompare: CCx DMA request sent when CCx event occurs
1: OnUpdate: CCx DMA request sent when update event occurs

MMS

Bits 4-6: Master mode selection.

Allowed values:
0: Reset: The UG bit from the TIMx_EGR register is used as trigger output
1: Enable: The counter enable signal, CNT_EN, is used as trigger output
2: Update: The update event is selected as trigger output
3: ComparePulse: The trigger output send a positive pulse when the CC1IF flag it to be set, as soon as a capture or a compare match occurred
4: CompareOC1: OC1REF signal is used as trigger output
5: CompareOC2: OC2REF signal is used as trigger output
6: CompareOC3: OC3REF signal is used as trigger output
7: CompareOC4: OC4REF signal is used as trigger output

TI1S

Bit 7: TI1 selection.

Allowed values:
0: Normal: The TIMx_CH1 pin is connected to TI1 input
1: XOR: The TIMx_CH1, CH2, CH3 pins are connected to TI1 input

SMCR

slave mode control register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

7/9 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															SMS_3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ETP rw	ECE rw	ETPS rw		ETF rw				MSM rw	TS rw			OCCS rw	SMS rw

Toggle fields

SMS

Bits 0-2: Slave mode selection.

Allowed values:
0: Disabled: Slave mode disabled - if CEN = ‘1 then the prescaler is clocked directly by the internal clock.
1: Encoder_Mode_1: Encoder mode 1 - Counter counts up/down on TI2FP1 edge depending on TI1FP2 level.
2: Encoder_Mode_2: Encoder mode 2 - Counter counts up/down on TI1FP2 edge depending on TI2FP1 level.
3: Encoder_Mode_3: Encoder mode 3 - Counter counts up/down on both TI1FP1 and TI2FP2 edges depending on the level of the other input.
4: Reset_Mode: Reset Mode - Rising edge of the selected trigger input (TRGI) reinitializes the counter and generates an update of the registers.
5: Gated_Mode: Gated Mode - The counter clock is enabled when the trigger input (TRGI) is high. The counter stops (but is not reset) as soon as the trigger becomes low. Both start and stop of the counter are controlled.
6: Trigger_Mode: Trigger Mode - The counter starts at a rising edge of the trigger TRGI (but it is not reset). Only the start of the counter is controlled.
7: Ext_Clock_Mode: External Clock Mode 1 - Rising edges of the selected trigger (TRGI) clock the counter.

OCCS

Bit 3: OCREF clear selection.

TS

Bits 4-6: Trigger selection.

Allowed values:
0: ITR0: Internal Trigger 0 (ITR0)
1: ITR1: Internal Trigger 1 (ITR1)
2: ITR2: Internal Trigger 2 (ITR2)
4: TI1F_ED: TI1 Edge Detector (TI1F_ED)
5: TI1FP1: Filtered Timer Input 1 (TI1FP1)
6: TI2FP2: Filtered Timer Input 2 (TI2FP2)
7: ETRF: External Trigger input (ETRF)

MSM

Bit 7: Master/Slave mode.

Allowed values:
0: NoSync: No action
1: Sync: The effect of an event on the trigger input (TRGI) is delayed to allow a perfect synchronization between the current timer and its slaves (through TRGO). It is useful if we want to synchronize several timers on a single external event.

ETF

Bits 8-11: External trigger filter.

Allowed values:
0: NoFilter: No filter, sampling is done at fDTS
1: FCK_INT_N2: fSAMPLING=fCK_INT, N=2
2: FCK_INT_N4: fSAMPLING=fCK_INT, N=4
3: FCK_INT_N8: fSAMPLING=fCK_INT, N=8
4: FDTS_Div2_N6: fSAMPLING=fDTS/2, N=6
5: FDTS_Div2_N8: fSAMPLING=fDTS/2, N=8
6: FDTS_Div4_N6: fSAMPLING=fDTS/4, N=6
7: FDTS_Div4_N8: fSAMPLING=fDTS/4, N=8
8: FDTS_Div8_N6: fSAMPLING=fDTS/8, N=6
9: FDTS_Div8_N8: fSAMPLING=fDTS/8, N=8
10: FDTS_Div16_N5: fSAMPLING=fDTS/16, N=5
11: FDTS_Div16_N6: fSAMPLING=fDTS/16, N=6
12: FDTS_Div16_N8: fSAMPLING=fDTS/16, N=8
13: FDTS_Div32_N5: fSAMPLING=fDTS/32, N=5
14: FDTS_Div32_N6: fSAMPLING=fDTS/32, N=6
15: FDTS_Div32_N8: fSAMPLING=fDTS/32, N=8

ETPS

Bits 12-13: External trigger prescaler.

Allowed values:
0: Div1: Prescaler OFF
1: Div2: ETRP frequency divided by 2
2: Div4: ETRP frequency divided by 4
3: Div8: ETRP frequency divided by 8

ECE

Bit 14: External clock enable.

Allowed values:
0: Disabled: External clock mode 2 disabled
1: Enabled: External clock mode 2 enabled. The counter is clocked by any active edge on the ETRF signal.

ETP

Bit 15: External trigger polarity.

Allowed values:
0: NotInverted: ETR is noninverted, active at high level or rising edge
1: Inverted: ETR is inverted, active at low level or falling edge

SMS_3

Bit 16: Slave mode selection bit3.

DIER

DMA/Interrupt enable register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

12/12 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	TDE rw		CC[4]DE rw	CC[3]DE rw	CC[2]DE rw	CC[1]DE rw	UDE rw		TIE rw		CC[4]IE rw	CC[3]IE rw	CC[2]IE rw	CC[1]IE rw	UIE rw

Toggle fields

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

CC[1]IE

Bit 1: Capture/Compare 1 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC[2]IE

Bit 2: Capture/Compare 2 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC[3]IE

Bit 3: Capture/Compare 3 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC[4]IE

Bit 4: Capture/Compare 4 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

TIE

Bit 6: Trigger interrupt enable.

Allowed values:
0: Disabled: Trigger interrupt disabled
1: Enabled: Trigger interrupt enabled

UDE

Bit 8: Update DMA request enable.

Allowed values:
0: Disabled: Update DMA request disabled
1: Enabled: Update DMA request enabled

CC[1]DE

Bit 9: Capture/Compare 1 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC[2]DE

Bit 10: Capture/Compare 2 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC[3]DE

Bit 11: Capture/Compare 3 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC[4]DE

Bit 12: Capture/Compare 4 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

TDE

Bit 14: Trigger DMA request enable.

Allowed values:
0: Disabled: Trigger DMA request disabled
1: Enabled: Trigger DMA request enabled

SR

status register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

10/10 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			CC[4]OF rw	CC[3]OF rw	CC[2]OF rw	CC[1]OF rw			TIF rw		CC[4]IF rw	CC[3]IF rw	CC[2]IF rw	CC[1]IF rw	UIF rw

Toggle fields

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: NoUpdateOccurred: No update occurred
1: UpdatePending: Update interrupt pending

CC[1]IF

Bit 1: Capture/compare 1 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC[2]IF

Bit 2: Capture/compare 2 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC[3]IF

Bit 3: Capture/compare 3 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC[4]IF

Bit 4: Capture/compare 4 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

TIF

Bit 6: Trigger interrupt flag.

Allowed values:
0: NoTrigger: No trigger event occurred
1: Trigger: Trigger interrupt pending

CC[1]OF

Bit 9: Capture/Compare 1 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC[2]OF

Bit 10: Capture/Compare 2 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC[3]OF

Bit 11: Capture/Compare 3 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC[4]OF

Bit 12: Capture/Compare 4 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

EGR

event generation register

Offset: 0x14, size: 32, reset: 0x00000000, access: write-only

6/6 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
									TG w		CC[4]G w	CC[3]G w	CC[2]G w	CC[1]G w	UG w

Toggle fields

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the registers.

CC[1]G

Bit 1: Capture/compare 1 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC[2]G

Bit 2: Capture/compare 2 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC[3]G

Bit 3: Capture/compare 3 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC[4]G

Bit 4: Capture/compare 4 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

TG

Bit 6: Trigger generation.

Allowed values:
1: Trigger: The TIF flag is set in TIMx_SR register. Related interrupt or DMA transfer can occur if enabled.

CCMR1_Input

capture/compare mode register 1 (input mode)

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

4/6 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IC[2]F rw				IC[2]PSC rw		CC[2]S rw		IC[1]F rw				IC[1]PSC rw		CC[1]S rw

Toggle fields

CC[1]S

Bits 0-1: Capture/Compare 1 selection.

Allowed values:
1: TI1: CC1 channel is configured as input, IC1 is mapped on TI1
2: TI2: CC1 channel is configured as input, IC1 is mapped on TI2
3: TRC: CC1 channel is configured as input, IC1 is mapped on TRC

IC[1]PSC

Bits 2-3: Input capture 1 prescaler.

IC[1]F

Bits 4-7: Input capture 1 filter.

Allowed values:
0: NoFilter: No filter, sampling is done at fDTS
1: FCK_INT_N2: fSAMPLING=fCK_INT, N=2
2: FCK_INT_N4: fSAMPLING=fCK_INT, N=4
3: FCK_INT_N8: fSAMPLING=fCK_INT, N=8
4: FDTS_Div2_N6: fSAMPLING=fDTS/2, N=6
5: FDTS_Div2_N8: fSAMPLING=fDTS/2, N=8
6: FDTS_Div4_N6: fSAMPLING=fDTS/4, N=6
7: FDTS_Div4_N8: fSAMPLING=fDTS/4, N=8
8: FDTS_Div8_N6: fSAMPLING=fDTS/8, N=6
9: FDTS_Div8_N8: fSAMPLING=fDTS/8, N=8
10: FDTS_Div16_N5: fSAMPLING=fDTS/16, N=5
11: FDTS_Div16_N6: fSAMPLING=fDTS/16, N=6
12: FDTS_Div16_N8: fSAMPLING=fDTS/16, N=8
13: FDTS_Div32_N5: fSAMPLING=fDTS/32, N=5
14: FDTS_Div32_N6: fSAMPLING=fDTS/32, N=6
15: FDTS_Div32_N8: fSAMPLING=fDTS/32, N=8

CC[2]S

Bits 8-9: Capture/Compare 2 selection.

Allowed values:
1: TI1: CC1 channel is configured as input, IC1 is mapped on TI1
2: TI2: CC1 channel is configured as input, IC1 is mapped on TI2
3: TRC: CC1 channel is configured as input, IC1 is mapped on TRC

IC[2]PSC

Bits 10-11: Input capture 2 prescaler.

IC[2]F

Bits 12-15: Input capture 2 filter.

Allowed values:
0: NoFilter: No filter, sampling is done at fDTS
1: FCK_INT_N2: fSAMPLING=fCK_INT, N=2
2: FCK_INT_N4: fSAMPLING=fCK_INT, N=4
3: FCK_INT_N8: fSAMPLING=fCK_INT, N=8
4: FDTS_Div2_N6: fSAMPLING=fDTS/2, N=6
5: FDTS_Div2_N8: fSAMPLING=fDTS/2, N=8
6: FDTS_Div4_N6: fSAMPLING=fDTS/4, N=6
7: FDTS_Div4_N8: fSAMPLING=fDTS/4, N=8
8: FDTS_Div8_N6: fSAMPLING=fDTS/8, N=6
9: FDTS_Div8_N8: fSAMPLING=fDTS/8, N=8
10: FDTS_Div16_N5: fSAMPLING=fDTS/16, N=5
11: FDTS_Div16_N6: fSAMPLING=fDTS/16, N=6
12: FDTS_Div16_N8: fSAMPLING=fDTS/16, N=8
13: FDTS_Div32_N5: fSAMPLING=fDTS/32, N=5
14: FDTS_Div32_N6: fSAMPLING=fDTS/32, N=6
15: FDTS_Div32_N8: fSAMPLING=fDTS/32, N=8

CCMR1_Output

capture/compare mode register 1 (output mode)

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

8/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
							OC[2]M_3 rw								OC[1]M_3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OC[2]CE rw	OC[2]M rw			OC[2]PE rw	OC[2]FE rw	CC[2]S rw		OC[1]CE rw	OC[1]M rw			OC[1]PE rw	OC[1]FE rw	CC[1]S rw

Toggle fields

CC[1]S

Bits 0-1: Capture/Compare 1 selection.

Allowed values:
0: Output: CC1 channel is configured as output

OC[1]FE

Bit 2: Output compare 1 fast enable.

OC[1]PE

Bit 3: Output compare 1 preload enable.

Allowed values:
0: Disabled: Preload register on CCR1 disabled. New values written to CCR1 are taken into account immediately
1: Enabled: Preload register on CCR1 enabled. Preload value is loaded into active register on each update event

OC[1]M

Bits 4-6: Output compare 1 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[1]CE

Bit 7: Output compare 1 clear enable.

CC[2]S

Bits 8-9: Capture/Compare 2 selection.

Allowed values:
0: Output: CC1 channel is configured as output

OC[2]FE

Bit 10: Output compare 2 fast enable.

OC[2]PE

Bit 11: Output compare 2 preload enable.

Allowed values:
0: Disabled: Preload register on CCR1 disabled. New values written to CCR1 are taken into account immediately
1: Enabled: Preload register on CCR1 enabled. Preload value is loaded into active register on each update event

OC[2]M

Bits 12-14: Output compare 2 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[2]CE

Bit 15: Output compare 2 clear enable.

OC[1]M_3

Bit 16: Output compare 1 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

OC[2]M_3

Bit 24: Output compare 2 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

CCMR2_Input

capture/compare mode register 2 (input mode)

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

6/6 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IC[4]F rw				IC[4]PSC rw		CC[4]S rw		IC[3]F rw				IC[3]PSC rw		CC[3]S rw

Toggle fields

CC[3]S

Bits 0-1: Capture/Compare 3 selection.

Allowed values:
1: TI3: CC3 channel is configured as input, IC3 is mapped on TI3
2: TI4: CC3 channel is configured as input, IC3 is mapped on TI4
3: TRC: CC3 channel is configured as input, IC3 is mapped on TRC

IC[3]PSC

Bits 2-3: Input capture 3 prescaler.

Allowed values: 0x0-0x3

IC[3]F

Bits 4-7: Input capture 3 filter.

Allowed values: 0x0-0xf

CC[4]S

Bits 8-9: Capture/Compare 4 selection.

Allowed values:
1: TI3: CC3 channel is configured as input, IC3 is mapped on TI3
2: TI4: CC3 channel is configured as input, IC3 is mapped on TI4
3: TRC: CC3 channel is configured as input, IC3 is mapped on TRC

IC[4]PSC

Bits 10-11: Input capture 4 prescaler.

Allowed values: 0x0-0x3

IC[4]F

Bits 12-15: Input capture 4 filter.

Allowed values: 0x0-0xf

CCMR2_Output

capture/compare mode register 2 (output mode)

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

8/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
							OC[4]M_3 rw								OC[3]M_3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OC[4]CE rw	OC[4]M rw			OC[4]PE rw	OC[4]FE rw	CC[4]S rw		OC[3]CE rw	OC[3]M rw			OC[3]PE rw	OC[3]FE rw	CC[3]S rw

Toggle fields

CC[3]S

Bits 0-1: Capture/Compare 3 selection.

Allowed values:
0: Output: CC3 channel is configured as output

OC[3]FE

Bit 2: Output compare 3 fast enable.

OC[3]PE

Bit 3: Output compare 3 preload enable.

Allowed values:
0: Disabled: Preload register on CCR3 disabled. New values written to CCR3 are taken into account immediately
1: Enabled: Preload register on CCR3 enabled. Preload value is loaded into active register on each update event

OC[3]M

Bits 4-6: Output compare 3 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[3]CE

Bit 7: Output compare 3 clear enable.

CC[4]S

Bits 8-9: Capture/Compare 4 selection.

Allowed values:
0: Output: CC3 channel is configured as output

OC[4]FE

Bit 10: Output compare 4 fast enable.

OC[4]PE

Bit 11: Output compare 4 preload enable.

Allowed values:
0: Disabled: Preload register on CCR3 disabled. New values written to CCR3 are taken into account immediately
1: Enabled: Preload register on CCR3 enabled. Preload value is loaded into active register on each update event

OC[4]M

Bits 12-14: Output compare 4 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[4]CE

Bit 15: Output compare 4 clear enable.

OC[3]M_3

Bit 16: Output compare 3 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

OC[4]M_3

Bit 24: Output compare 4 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

CCER

capture/compare enable register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

0/12 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CC[4]NP rw		CC[4]P rw	CC[4]E rw	CC[3]NP rw		CC[3]P rw	CC[3]E rw	CC[2]NP rw		CC[2]P rw	CC[2]E rw	CC[1]NP rw		CC[1]P rw	CC[1]E rw

Toggle fields

CC[1]E

Bit 0: Capture/Compare 1 output enable.

CC[1]P

Bit 1: Capture/Compare 1 output Polarity.

CC[1]NP

Bit 3: Capture/Compare 1 output Polarity.

CC[2]E

Bit 4: Capture/Compare 2 output enable.

CC[2]P

Bit 5: Capture/Compare 2 output Polarity.

CC[2]NP

Bit 7: Capture/Compare 2 output Polarity.

CC[3]E

Bit 8: Capture/Compare 3 output enable.

CC[3]P

Bit 9: Capture/Compare 3 output Polarity.

CC[3]NP

Bit 11: Capture/Compare 3 output Polarity.

CC[4]E

Bit 12: Capture/Compare 4 output enable.

CC[4]P

Bit 13: Capture/Compare 4 output Polarity.

CC[4]NP

Bit 15: Capture/Compare 4 output Polarity.

CNT

counter

Offset: 0x24, size: 32, reset: 0x00000000, access: read-write

1/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
UIFCPY rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CNT rw

Toggle fields

CNT

Bits 0-15: Counter value.

Allowed values: 0x0-0xffff

UIFCPY

Bit 31: if IUFREMAP=0 than CNT with read write access else UIFCPY with read only access.

PSC

prescaler

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PSC rw

Toggle fields

PSC

Bits 0-15: Prescaler value.

Allowed values: 0x0-0xffff

ARR

auto-reload register

Offset: 0x2c, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ARR rw

Toggle fields

ARR

Bits 0-15: Auto-reload value.

Allowed values: 0x0-0xffff

CCR[1]

capture/compare register

Offset: 0x34, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

Allowed values: 0x0-0xffff

CCR[2]

capture/compare register

Offset: 0x38, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

Allowed values: 0x0-0xffff

CCR[3]

capture/compare register

Offset: 0x3c, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

Allowed values: 0x0-0xffff

CCR[4]

capture/compare register

Offset: 0x40, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

Allowed values: 0x0-0xffff

DCR

DMA control register

Offset: 0x48, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			DBL rw								DBA rw

Toggle fields

DBA

Bits 0-4: DMA base address.

Allowed values: 0x0-0x1f

DBL

Bits 8-12: DMA burst length.

Allowed values: 0x0-0x12

DMAR

DMA address for full transfer

Offset: 0x4c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DMAB rw

Toggle fields

DMAB

Bits 0-15: DMA register for burst accesses.

TIM6

0x40001000: Basic timers

14/15 fields covered.

Toggle register map

Offset	Name	31	15	11	8	7	6	3	2	1	0
0x0	CR1			UIFREMAP		ARPE		OPM	URS	UDIS	CEN
0x4	CR2						MMS
0xc	DIER				UDE						UIE
0x10	SR										UIF
0x14	EGR										UG
0x24	CNT	UIFCPY	CNT
0x28	PSC		PSC
0x2c	ARR		ARR

Toggle registers

CR1

control register 1

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

5/6 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				UIFREMAP rw				ARPE rw				OPM rw	URS rw	UDIS rw	CEN rw

Toggle fields

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

Allowed values:
0: AnyEvent: Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request
1: CounterOnly: Only counter overflow/underflow generates an update interrupt or DMA request

OPM

Bit 3: One-pulse mode.

Allowed values:
0: Disabled: Counter is not stopped at update event
1: Enabled: Counter stops counting at the next update event (clearing the CEN bit)

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

UIFREMAP

Bit 11: UIF status bit remapping.

CR2

control register 2

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
									MMS rw

Toggle fields

MMS

Bits 4-6: Master mode selection.

Allowed values:
0: Reset: Use UG bit from TIMx_EGR register
1: Enable: Use CNT bit from TIMx_CEN register
2: Update: Use the update event

DIER

DMA/Interrupt enable register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							UDE rw								UIE rw

Toggle fields

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

UDE

Bit 8: Update DMA request enable.

Allowed values:
0: Disabled: Update DMA request disabled
1: Enabled: Update DMA request enabled

SR

status register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
															UIF rw

Toggle fields

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: NoUpdateOccurred: No update occurred
1: UpdatePending: Update interrupt pending

EGR

event generation register

Offset: 0x14, size: 32, reset: 0x00000000, access: write-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
															UG w

Toggle fields

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the registers.

CNT

counter

Offset: 0x24, size: 32, reset: 0x00000000, access: Unspecified

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
UIFCPY r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CNT rw

Toggle fields

CNT

Bits 0-15: Low counter value.

Allowed values: 0x0-0xffff

UIFCPY

Bit 31: UIF Copy.

PSC

prescaler

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PSC rw

Toggle fields

PSC

Bits 0-15: Prescaler value.

Allowed values: 0x0-0xffff

ARR

auto-reload register

Offset: 0x2c, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ARR rw

Toggle fields

ARR

Bits 0-15: Low Auto-reload value.

Allowed values: 0x0-0xffff

TIM7

0x40001400: Basic timers

14/15 fields covered.

Toggle register map

Offset	Name	31	15	11	8	7	6	3	2	1	0
0x0	CR1			UIFREMAP		ARPE		OPM	URS	UDIS	CEN
0x4	CR2						MMS
0xc	DIER				UDE						UIE
0x10	SR										UIF
0x14	EGR										UG
0x24	CNT	UIFCPY	CNT
0x28	PSC		PSC
0x2c	ARR		ARR

Toggle registers

CR1

control register 1

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

5/6 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				UIFREMAP rw				ARPE rw				OPM rw	URS rw	UDIS rw	CEN rw

Toggle fields

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

Allowed values:
0: AnyEvent: Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request
1: CounterOnly: Only counter overflow/underflow generates an update interrupt or DMA request

OPM

Bit 3: One-pulse mode.

Allowed values:
0: Disabled: Counter is not stopped at update event
1: Enabled: Counter stops counting at the next update event (clearing the CEN bit)

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

UIFREMAP

Bit 11: UIF status bit remapping.

CR2

control register 2

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
									MMS rw

Toggle fields

MMS

Bits 4-6: Master mode selection.

Allowed values:
0: Reset: Use UG bit from TIMx_EGR register
1: Enable: Use CNT bit from TIMx_CEN register
2: Update: Use the update event

DIER

DMA/Interrupt enable register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							UDE rw								UIE rw

Toggle fields

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

UDE

Bit 8: Update DMA request enable.

Allowed values:
0: Disabled: Update DMA request disabled
1: Enabled: Update DMA request enabled

SR

status register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
															UIF rw

Toggle fields

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: NoUpdateOccurred: No update occurred
1: UpdatePending: Update interrupt pending

EGR

event generation register

Offset: 0x14, size: 32, reset: 0x00000000, access: write-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
															UG w

Toggle fields

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the registers.

CNT

counter

Offset: 0x24, size: 32, reset: 0x00000000, access: Unspecified

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
UIFCPY r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CNT rw

Toggle fields

CNT

Bits 0-15: Low counter value.

Allowed values: 0x0-0xffff

UIFCPY

Bit 31: UIF Copy.

PSC

prescaler

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PSC rw

Toggle fields

PSC

Bits 0-15: Prescaler value.

Allowed values: 0x0-0xffff

ARR

auto-reload register

Offset: 0x2c, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ARR rw

Toggle fields

ARR

Bits 0-15: Low Auto-reload value.

Allowed values: 0x0-0xffff

TIM8

0x40013400: Advanced-timers

107/168 fields covered.

Toggle register map

Offset	Name	31	30	29	25	24	23	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	CR1																	UIFREMAP		CKD		ARPE	CMS		DIR	OPM	URS	UDIS	CEN
0x4	CR2						MMS2				OIS[6]		OIS[5]		OIS[4]	OIS[3]N	OIS[3]	OIS[2]N	OIS[2]	OIS[1]N	OIS[1]	TI1S	MMS			CCDS	CCUS		CCPC
0x8	SMCR												SMS3	ETP	ECE	ETPS		ETF				MSM	TS			OCCS	SMS
0xc	DIER														TDE	COMDE	CC[4]DE	CC[3]DE	CC[2]DE	CC[1]DE	UDE	BIE	TIE	COMIE	CC[4]IE	CC[3]IE	CC[2]IE	CC[1]IE	UIE
0x10	SR											C6IF	C5IF				CC[4]OF	CC[3]OF	CC[2]OF	CC[1]OF	B2IF	BIF	TIF	COMIF	CC[4]IF	CC[3]IF	CC[2]IF	CC[1]IF	UIF
0x14	EGR																				B2G	BG	TG	COMG	CC[4]G	CC[3]G	CC[2]G	CC[1]G	UG
0x18	CCMR1_Input													IC[2]F				IC[2]PSC		CC[2]S		IC[1]F				IC[1]PSC		CC[1]S
0x18	CCMR1_Output					OC[2]M_3							OC[1]M_3	OC[2]CE	OC[2]M			OC[2]PE	OC[2]FE	CC[2]S		OC[1]CE	OC[1]M			OC[1]PE	OC[1]FE	CC[1]S
0x1c	CCMR2_Input													IC[4]F				IC[4]PSC		CC[4]S		IC[3]F				IC[3]PSC		CC[3]S
0x1c	CCMR2_Output					OC[4]M_3							OC[3]M_3	OC[4]CE	OC[4]M			OC[4]PE	OC[4]FE	CC[4]S		OC[3]CE	OC[3]M			OC[3]PE	OC[3]FE	CC[3]S
0x20	CCER							CC[6]P	CC[6]E			CC[5]P	CC[5]E	CC[4]NP		CC[4]P	CC[4]E	CC[3]NP	CC[3]NE	CC[3]P	CC[3]E	CC[2]NP	CC[2]NE	CC[2]P	CC[2]E	CC[1]NP	CC[1]NE	CC[1]P	CC[1]E
0x24	CNT	UIFCPY												CNT
0x28	PSC													PSC
0x2c	ARR													ARR
0x30	RCR													REP
0x34	CCR[1]													CCR
0x38	CCR[2]													CCR
0x3c	CCR[3]													CCR
0x40	CCR[4]													CCR
0x44	BDTR				BK2P	BK2E	BK2F			BKF				MOE	AOE	BKP	BKE	OSSR	OSSI	LOCK		DTG
0x48	DCR																DBL								DBA
0x4c	DMAR													DMAB
0x54	CCMR3_Output					OC[6]M_3							OC[5]M_3	OC[6]CE	OC[6]M			OC[6]PE	OC[6]FE			OC[5]CE	OC[5]M			OC[5]PE	OC[5]FE
0x58	CCR5	GC5C3	GC5C2	GC5C1										CCR
0x5c	CCR6													CCR
0x60	OR																									TIM8_ETR_ADC3_RMP		TIM8_ETR_ADC2_RMP

Toggle registers

CR1

control register 1

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

8/9 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				UIFREMAP rw		CKD rw		ARPE rw	CMS rw		DIR rw	OPM rw	URS rw	UDIS rw	CEN rw

Toggle fields

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

Allowed values:
0: AnyEvent: Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request
1: CounterOnly: Only counter overflow/underflow generates an update interrupt or DMA request

OPM

Bit 3: One-pulse mode.

Allowed values:
0: Disabled: Counter is not stopped at update event
1: Enabled: Counter stops counting at the next update event (clearing the CEN bit)

DIR

Bit 4: Direction.

Allowed values:
0: Up: Counter used as upcounter
1: Down: Counter used as downcounter

CMS

Bits 5-6: Center-aligned mode selection.

Allowed values:
0: EdgeAligned: The counter counts up or down depending on the direction bit
1: CenterAligned1: The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting down.
2: CenterAligned2: The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting up.
3: CenterAligned3: The counter counts up and down alternatively. Output compare interrupt flags are set both when the counter is counting up or down.

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CKD

Bits 8-9: Clock division.

Allowed values:
0: Div1: t_DTS = t_CK_INT
1: Div2: t_DTS = 2 × t_CK_INT
2: Div4: t_DTS = 4 × t_CK_INT

UIFREMAP

Bit 11: UIF status bit remapping.

CR2

control register 2

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

12/15 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								MMS2 rw					OIS[6] rw		OIS[5] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	OIS[4] rw	OIS[3]N rw	OIS[3] rw	OIS[2]N rw	OIS[2] rw	OIS[1]N rw	OIS[1] rw	TI1S rw	MMS rw			CCDS rw	CCUS rw		CCPC rw

Toggle fields

CCPC

Bit 0: Capture/compare preloaded control.

CCUS

Bit 2: Capture/compare control update selection.

CCDS

Bit 3: Capture/compare DMA selection.

Allowed values:
0: OnCompare: CCx DMA request sent when CCx event occurs
1: OnUpdate: CCx DMA request sent when update event occurs

MMS

Bits 4-6: Master mode selection.

Allowed values:
0: Reset: The UG bit from the TIMx_EGR register is used as trigger output
1: Enable: The counter enable signal, CNT_EN, is used as trigger output
2: Update: The update event is selected as trigger output
3: ComparePulse: The trigger output send a positive pulse when the CC1IF flag it to be set, as soon as a capture or a compare match occurred
4: CompareOC1: OC1REF signal is used as trigger output
5: CompareOC2: OC2REF signal is used as trigger output
6: CompareOC3: OC3REF signal is used as trigger output
7: CompareOC4: OC4REF signal is used as trigger output

TI1S

Bit 7: TI1 selection.

Allowed values:
0: Normal: The TIMx_CH1 pin is connected to TI1 input
1: XOR: The TIMx_CH1, CH2, CH3 pins are connected to TI1 input

OIS[1]

Bit 8: Output Idle state (OC1 output).

Allowed values:
0: Reset: OCx=0 (after a dead-time if OCx(N) is implemented) when MOE=0
1: Set: OCx=1 (after a dead-time if OCx(N) is implemented) when MOE=0

OIS[1]N

Bit 9: Output Idle state (OC1N output).

Allowed values:
0: Reset: OCxN=0 after a dead-time when MOE=0
1: Set: OCxN=1 after a dead-time when MOE=0

OIS[2]

Bit 10: Output Idle state (OC2 output).

Allowed values:
0: Reset: OCx=0 (after a dead-time if OCx(N) is implemented) when MOE=0
1: Set: OCx=1 (after a dead-time if OCx(N) is implemented) when MOE=0

OIS[2]N

Bit 11: Output Idle state (OC2N output).

Allowed values:
0: Reset: OCxN=0 after a dead-time when MOE=0
1: Set: OCxN=1 after a dead-time when MOE=0

OIS[3]

Bit 12: Output Idle state (OC3 output).

Allowed values:
0: Reset: OCx=0 (after a dead-time if OCx(N) is implemented) when MOE=0
1: Set: OCx=1 (after a dead-time if OCx(N) is implemented) when MOE=0

OIS[3]N

Bit 13: Output Idle state (OC3N output).

Allowed values:
0: Reset: OCxN=0 after a dead-time when MOE=0
1: Set: OCxN=1 after a dead-time when MOE=0

OIS[4]

Bit 14: Output Idle state (OC4 output).

Allowed values:
0: Reset: OCx=0 (after a dead-time if OCx(N) is implemented) when MOE=0
1: Set: OCx=1 (after a dead-time if OCx(N) is implemented) when MOE=0

OIS[5]

Bit 16: Output Idle state (OC5 output).

Allowed values:
0: Reset: OCx=0 (after a dead-time if OCx(N) is implemented) when MOE=0
1: Set: OCx=1 (after a dead-time if OCx(N) is implemented) when MOE=0

OIS[6]

Bit 18: Output Idle state (OC6 output).

Allowed values:
0: Reset: OCx=0 (after a dead-time if OCx(N) is implemented) when MOE=0
1: Set: OCx=1 (after a dead-time if OCx(N) is implemented) when MOE=0

MMS2

Bits 20-23: Master mode selection 2.

SMCR

slave mode control register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

7/9 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															SMS3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ETP rw	ECE rw	ETPS rw		ETF rw				MSM rw	TS rw			OCCS rw	SMS rw

Toggle fields

SMS

Bits 0-2: Slave mode selection.

Allowed values:
0: Disabled: Slave mode disabled - if CEN = ‘1 then the prescaler is clocked directly by the internal clock.
1: Encoder_Mode_1: Encoder mode 1 - Counter counts up/down on TI2FP1 edge depending on TI1FP2 level.
2: Encoder_Mode_2: Encoder mode 2 - Counter counts up/down on TI1FP2 edge depending on TI2FP1 level.
3: Encoder_Mode_3: Encoder mode 3 - Counter counts up/down on both TI1FP1 and TI2FP2 edges depending on the level of the other input.
4: Reset_Mode: Reset Mode - Rising edge of the selected trigger input (TRGI) reinitializes the counter and generates an update of the registers.
5: Gated_Mode: Gated Mode - The counter clock is enabled when the trigger input (TRGI) is high. The counter stops (but is not reset) as soon as the trigger becomes low. Both start and stop of the counter are controlled.
6: Trigger_Mode: Trigger Mode - The counter starts at a rising edge of the trigger TRGI (but it is not reset). Only the start of the counter is controlled.
7: Ext_Clock_Mode: External Clock Mode 1 - Rising edges of the selected trigger (TRGI) clock the counter.

OCCS

Bit 3: OCREF clear selection.

TS

Bits 4-6: Trigger selection.

Allowed values:
0: ITR0: Internal Trigger 0 (ITR0)
1: ITR1: Internal Trigger 1 (ITR1)
2: ITR2: Internal Trigger 2 (ITR2)
4: TI1F_ED: TI1 Edge Detector (TI1F_ED)
5: TI1FP1: Filtered Timer Input 1 (TI1FP1)
6: TI2FP2: Filtered Timer Input 2 (TI2FP2)
7: ETRF: External Trigger input (ETRF)

MSM

Bit 7: Master/Slave mode.

Allowed values:
0: NoSync: No action
1: Sync: The effect of an event on the trigger input (TRGI) is delayed to allow a perfect synchronization between the current timer and its slaves (through TRGO). It is useful if we want to synchronize several timers on a single external event.

ETF

Bits 8-11: External trigger filter.

Allowed values:
0: NoFilter: No filter, sampling is done at fDTS
1: FCK_INT_N2: fSAMPLING=fCK_INT, N=2
2: FCK_INT_N4: fSAMPLING=fCK_INT, N=4
3: FCK_INT_N8: fSAMPLING=fCK_INT, N=8
4: FDTS_Div2_N6: fSAMPLING=fDTS/2, N=6
5: FDTS_Div2_N8: fSAMPLING=fDTS/2, N=8
6: FDTS_Div4_N6: fSAMPLING=fDTS/4, N=6
7: FDTS_Div4_N8: fSAMPLING=fDTS/4, N=8
8: FDTS_Div8_N6: fSAMPLING=fDTS/8, N=6
9: FDTS_Div8_N8: fSAMPLING=fDTS/8, N=8
10: FDTS_Div16_N5: fSAMPLING=fDTS/16, N=5
11: FDTS_Div16_N6: fSAMPLING=fDTS/16, N=6
12: FDTS_Div16_N8: fSAMPLING=fDTS/16, N=8
13: FDTS_Div32_N5: fSAMPLING=fDTS/32, N=5
14: FDTS_Div32_N6: fSAMPLING=fDTS/32, N=6
15: FDTS_Div32_N8: fSAMPLING=fDTS/32, N=8

ETPS

Bits 12-13: External trigger prescaler.

Allowed values:
0: Div1: Prescaler OFF
1: Div2: ETRP frequency divided by 2
2: Div4: ETRP frequency divided by 4
3: Div8: ETRP frequency divided by 8

ECE

Bit 14: External clock enable.

Allowed values:
0: Disabled: External clock mode 2 disabled
1: Enabled: External clock mode 2 enabled. The counter is clocked by any active edge on the ETRF signal.

ETP

Bit 15: External trigger polarity.

Allowed values:
0: NotInverted: ETR is noninverted, active at high level or rising edge
1: Inverted: ETR is inverted, active at low level or falling edge

SMS3

Bit 16: Slave mode selection bit 3.

DIER

DMA/Interrupt enable register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

12/15 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	TDE rw	COMDE rw	CC[4]DE rw	CC[3]DE rw	CC[2]DE rw	CC[1]DE rw	UDE rw	BIE rw	TIE rw	COMIE rw	CC[4]IE rw	CC[3]IE rw	CC[2]IE rw	CC[1]IE rw	UIE rw

Toggle fields

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

CC[1]IE

Bit 1: Capture/Compare 1 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC[2]IE

Bit 2: Capture/Compare 2 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC[3]IE

Bit 3: Capture/Compare 3 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC[4]IE

Bit 4: Capture/Compare 4 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

COMIE

Bit 5: COM interrupt enable.

TIE

Bit 6: Trigger interrupt enable.

Allowed values:
0: Disabled: Trigger interrupt disabled
1: Enabled: Trigger interrupt enabled

BIE

Bit 7: Break interrupt enable.

UDE

Bit 8: Update DMA request enable.

Allowed values:
0: Disabled: Update DMA request disabled
1: Enabled: Update DMA request enabled

CC[1]DE

Bit 9: Capture/Compare 1 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC[2]DE

Bit 10: Capture/Compare 2 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC[3]DE

Bit 11: Capture/Compare 3 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC[4]DE

Bit 12: Capture/Compare 4 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

COMDE

Bit 13: COM DMA request enable.

TDE

Bit 14: Trigger DMA request enable.

Allowed values:
0: Disabled: Trigger DMA request disabled
1: Enabled: Trigger DMA request enabled

SR

status register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

10/15 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
														C6IF rw	C5IF rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			CC[4]OF rw	CC[3]OF rw	CC[2]OF rw	CC[1]OF rw	B2IF rw	BIF rw	TIF rw	COMIF rw	CC[4]IF rw	CC[3]IF rw	CC[2]IF rw	CC[1]IF rw	UIF rw

Toggle fields

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: NoUpdateOccurred: No update occurred
1: UpdatePending: Update interrupt pending

CC[1]IF

Bit 1: Capture/compare 1 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC[2]IF

Bit 2: Capture/compare 2 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC[3]IF

Bit 3: Capture/compare 3 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC[4]IF

Bit 4: Capture/compare 4 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

COMIF

Bit 5: COM interrupt flag.

TIF

Bit 6: Trigger interrupt flag.

Allowed values:
0: NoTrigger: No trigger event occurred
1: Trigger: Trigger interrupt pending

BIF

Bit 7: Break interrupt flag.

B2IF

Bit 8: Break 2 interrupt flag.

CC[1]OF

Bit 9: Capture/Compare 1 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC[2]OF

Bit 10: Capture/Compare 2 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC[3]OF

Bit 11: Capture/Compare 3 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC[4]OF

Bit 12: Capture/Compare 4 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

C5IF

Bit 16: Capture/Compare 5 interrupt flag.

C6IF

Bit 17: Capture/Compare 6 interrupt flag.

EGR

event generation register

Offset: 0x14, size: 32, reset: 0x00000000, access: write-only

6/9 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							B2G w	BG w	TG w	COMG w	CC[4]G w	CC[3]G w	CC[2]G w	CC[1]G w	UG w

Toggle fields

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the registers.

CC[1]G

Bit 1: Capture/compare 1 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC[2]G

Bit 2: Capture/compare 2 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC[3]G

Bit 3: Capture/compare 3 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC[4]G

Bit 4: Capture/compare 4 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

COMG

Bit 5: Capture/Compare control update generation.

TG

Bit 6: Trigger generation.

Allowed values:
1: Trigger: The TIF flag is set in TIMx_SR register. Related interrupt or DMA transfer can occur if enabled.

BG

Bit 7: Break generation.

B2G

Bit 8: Break 2 generation.

CCMR1_Input

capture/compare mode register 1 (input mode)

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

4/6 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IC[2]F rw				IC[2]PSC rw		CC[2]S rw		IC[1]F rw				IC[1]PSC rw		CC[1]S rw

Toggle fields

CC[1]S

Bits 0-1: Capture/Compare 1 selection.

Allowed values:
1: TI1: CC1 channel is configured as input, IC1 is mapped on TI1
2: TI2: CC1 channel is configured as input, IC1 is mapped on TI2
3: TRC: CC1 channel is configured as input, IC1 is mapped on TRC

IC[1]PSC

Bits 2-3: Input capture 1 prescaler.

IC[1]F

Bits 4-7: Input capture 1 filter.

Allowed values:
0: NoFilter: No filter, sampling is done at fDTS
1: FCK_INT_N2: fSAMPLING=fCK_INT, N=2
2: FCK_INT_N4: fSAMPLING=fCK_INT, N=4
3: FCK_INT_N8: fSAMPLING=fCK_INT, N=8
4: FDTS_Div2_N6: fSAMPLING=fDTS/2, N=6
5: FDTS_Div2_N8: fSAMPLING=fDTS/2, N=8
6: FDTS_Div4_N6: fSAMPLING=fDTS/4, N=6
7: FDTS_Div4_N8: fSAMPLING=fDTS/4, N=8
8: FDTS_Div8_N6: fSAMPLING=fDTS/8, N=6
9: FDTS_Div8_N8: fSAMPLING=fDTS/8, N=8
10: FDTS_Div16_N5: fSAMPLING=fDTS/16, N=5
11: FDTS_Div16_N6: fSAMPLING=fDTS/16, N=6
12: FDTS_Div16_N8: fSAMPLING=fDTS/16, N=8
13: FDTS_Div32_N5: fSAMPLING=fDTS/32, N=5
14: FDTS_Div32_N6: fSAMPLING=fDTS/32, N=6
15: FDTS_Div32_N8: fSAMPLING=fDTS/32, N=8

CC[2]S

Bits 8-9: Capture/Compare 2 selection.

Allowed values:
1: TI1: CC1 channel is configured as input, IC1 is mapped on TI1
2: TI2: CC1 channel is configured as input, IC1 is mapped on TI2
3: TRC: CC1 channel is configured as input, IC1 is mapped on TRC

IC[2]PSC

Bits 10-11: Input capture 2 prescaler.

IC[2]F

Bits 12-15: Input capture 2 filter.

Allowed values:
0: NoFilter: No filter, sampling is done at fDTS
1: FCK_INT_N2: fSAMPLING=fCK_INT, N=2
2: FCK_INT_N4: fSAMPLING=fCK_INT, N=4
3: FCK_INT_N8: fSAMPLING=fCK_INT, N=8
4: FDTS_Div2_N6: fSAMPLING=fDTS/2, N=6
5: FDTS_Div2_N8: fSAMPLING=fDTS/2, N=8
6: FDTS_Div4_N6: fSAMPLING=fDTS/4, N=6
7: FDTS_Div4_N8: fSAMPLING=fDTS/4, N=8
8: FDTS_Div8_N6: fSAMPLING=fDTS/8, N=6
9: FDTS_Div8_N8: fSAMPLING=fDTS/8, N=8
10: FDTS_Div16_N5: fSAMPLING=fDTS/16, N=5
11: FDTS_Div16_N6: fSAMPLING=fDTS/16, N=6
12: FDTS_Div16_N8: fSAMPLING=fDTS/16, N=8
13: FDTS_Div32_N5: fSAMPLING=fDTS/32, N=5
14: FDTS_Div32_N6: fSAMPLING=fDTS/32, N=6
15: FDTS_Div32_N8: fSAMPLING=fDTS/32, N=8

CCMR1_Output

capture/compare mode register (output mode)

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

8/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
							OC[2]M_3 rw								OC[1]M_3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OC[2]CE rw	OC[2]M rw			OC[2]PE rw	OC[2]FE rw	CC[2]S rw		OC[1]CE rw	OC[1]M rw			OC[1]PE rw	OC[1]FE rw	CC[1]S rw

Toggle fields

CC[1]S

Bits 0-1: Capture/Compare 1 selection.

Allowed values:
0: Output: CC1 channel is configured as output

OC[1]FE

Bit 2: Output compare 1 fast enable.

OC[1]PE

Bit 3: Output compare 1 preload enable.

Allowed values:
0: Disabled: Preload register on CCR1 disabled. New values written to CCR1 are taken into account immediately
1: Enabled: Preload register on CCR1 enabled. Preload value is loaded into active register on each update event

OC[1]M

Bits 4-6: Output compare 1 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[1]CE

Bit 7: Output compare 1 clear enable.

CC[2]S

Bits 8-9: Capture/Compare 2 selection.

Allowed values:
0: Output: CC1 channel is configured as output

OC[2]FE

Bit 10: Output compare 2 fast enable.

OC[2]PE

Bit 11: Output compare 2 preload enable.

Allowed values:
0: Disabled: Preload register on CCR1 disabled. New values written to CCR1 are taken into account immediately
1: Enabled: Preload register on CCR1 enabled. Preload value is loaded into active register on each update event

OC[2]M

Bits 12-14: Output compare 2 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[2]CE

Bit 15: Output compare 2 clear enable.

OC[1]M_3

Bit 16: Output compare 1 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

OC[2]M_3

Bit 24: Output compare 2 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

CCMR2_Input

capture/compare mode register 2 (input mode)

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

6/6 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IC[4]F rw				IC[4]PSC rw		CC[4]S rw		IC[3]F rw				IC[3]PSC rw		CC[3]S rw

Toggle fields

CC[3]S

Bits 0-1: Capture/Compare 3 selection.

Allowed values:
1: TI3: CC3 channel is configured as input, IC3 is mapped on TI3
2: TI4: CC3 channel is configured as input, IC3 is mapped on TI4
3: TRC: CC3 channel is configured as input, IC3 is mapped on TRC

IC[3]PSC

Bits 2-3: Input capture 3 prescaler.

Allowed values: 0x0-0x3

IC[3]F

Bits 4-7: Input capture 3 filter.

Allowed values: 0x0-0xf

CC[4]S

Bits 8-9: Capture/Compare 4 selection.

Allowed values:
1: TI3: CC3 channel is configured as input, IC3 is mapped on TI3
2: TI4: CC3 channel is configured as input, IC3 is mapped on TI4
3: TRC: CC3 channel is configured as input, IC3 is mapped on TRC

IC[4]PSC

Bits 10-11: Input capture 4 prescaler.

Allowed values: 0x0-0x3

IC[4]F

Bits 12-15: Input capture 4 filter.

Allowed values: 0x0-0xf

CCMR2_Output

capture/compare mode register (output mode)

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

8/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
							OC[4]M_3 rw								OC[3]M_3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OC[4]CE rw	OC[4]M rw			OC[4]PE rw	OC[4]FE rw	CC[4]S rw		OC[3]CE rw	OC[3]M rw			OC[3]PE rw	OC[3]FE rw	CC[3]S rw

Toggle fields

CC[3]S

Bits 0-1: Capture/Compare 3 selection.

Allowed values:
0: Output: CC3 channel is configured as output

OC[3]FE

Bit 2: Output compare 3 fast enable.

OC[3]PE

Bit 3: Output compare 3 preload enable.

Allowed values:
0: Disabled: Preload register on CCR3 disabled. New values written to CCR3 are taken into account immediately
1: Enabled: Preload register on CCR3 enabled. Preload value is loaded into active register on each update event

OC[3]M

Bits 4-6: Output compare 3 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[3]CE

Bit 7: Output compare 3 clear enable.

CC[4]S

Bits 8-9: Capture/Compare 4 selection.

Allowed values:
0: Output: CC3 channel is configured as output

OC[4]FE

Bit 10: Output compare 4 fast enable.

OC[4]PE

Bit 11: Output compare 4 preload enable.

Allowed values:
0: Disabled: Preload register on CCR3 disabled. New values written to CCR3 are taken into account immediately
1: Enabled: Preload register on CCR3 enabled. Preload value is loaded into active register on each update event

OC[4]M

Bits 12-14: Output compare 4 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[4]CE

Bit 15: Output compare 4 clear enable.

OC[3]M_3

Bit 16: Output compare 3 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

OC[4]M_3

Bit 24: Output compare 4 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

CCER

capture/compare enable register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

0/19 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
										CC[6]P rw	CC[6]E rw			CC[5]P rw	CC[5]E rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CC[4]NP rw		CC[4]P rw	CC[4]E rw	CC[3]NP rw	CC[3]NE rw	CC[3]P rw	CC[3]E rw	CC[2]NP rw	CC[2]NE rw	CC[2]P rw	CC[2]E rw	CC[1]NP rw	CC[1]NE rw	CC[1]P rw	CC[1]E rw

Toggle fields

CC[1]E

Bit 0: Capture/Compare 1 output enable.

CC[1]P

Bit 1: Capture/Compare 1 output Polarity.

CC[1]NE

Bit 2: Capture/Compare 1 complementary output enable.

CC[1]NP

Bit 3: Capture/Compare 1 output Polarity.

CC[2]E

Bit 4: Capture/Compare 2 output enable.

CC[2]P

Bit 5: Capture/Compare 2 output Polarity.

CC[2]NE

Bit 6: Capture/Compare 2 complementary output enable.

CC[2]NP

Bit 7: Capture/Compare 2 output Polarity.

CC[3]E

Bit 8: Capture/Compare 3 output enable.

CC[3]P

Bit 9: Capture/Compare 3 output Polarity.

CC[3]NE

Bit 10: Capture/Compare 3 complementary output enable.

CC[3]NP

Bit 11: Capture/Compare 3 output Polarity.

CC[4]E

Bit 12: Capture/Compare 4 output enable.

CC[4]P

Bit 13: Capture/Compare 4 output Polarity.

CC[4]NP

Bit 15: Capture/Compare 4 output Polarity.

CC[5]E

Bit 16: Capture/Compare 5 output enable.

CC[5]P

Bit 17: Capture/Compare 5 output Polarity.

CC[6]E

Bit 20: Capture/Compare 6 output enable.

CC[6]P

Bit 21: Capture/Compare 6 output Polarity.

CNT

counter

Offset: 0x24, size: 32, reset: 0x00000000, access: Unspecified

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
UIFCPY r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CNT rw

Toggle fields

CNT

Bits 0-15: counter value.

Allowed values: 0x0-0xffff

UIFCPY

Bit 31: UIF copy.

PSC

prescaler

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PSC rw

Toggle fields

PSC

Bits 0-15: Prescaler value.

Allowed values: 0x0-0xffff

ARR

auto-reload register

Offset: 0x2c, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ARR rw

Toggle fields

ARR

Bits 0-15: Auto-reload value.

Allowed values: 0x0-0xffff

RCR

repetition counter register

Offset: 0x30, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
REP rw

Toggle fields

REP

Bits 0-15: Repetition counter value.

CCR[1]

capture/compare register

Offset: 0x34, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

Allowed values: 0x0-0xffff

CCR[2]

capture/compare register

Offset: 0x38, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

Allowed values: 0x0-0xffff

CCR[3]

capture/compare register

Offset: 0x3c, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

Allowed values: 0x0-0xffff

CCR[4]

capture/compare register

Offset: 0x40, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

Allowed values: 0x0-0xffff

BDTR

break and dead-time register

Offset: 0x44, size: 32, reset: 0x00000000, access: read-write

10/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
						BK2P rw	BK2E rw	BK2F rw				BKF rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MOE rw	AOE rw	BKP rw	BKE rw	OSSR rw	OSSI rw	LOCK rw		DTG rw

Toggle fields

DTG

Bits 0-7: Dead-time generator setup.

Allowed values: 0x0-0xff

LOCK

Bits 8-9: Lock configuration.

Allowed values:
0: Off: No bit is write protected
1: Level1: Any bits except MOE, OSSR, OSSI and LOCK in TIMx_BDTR register, OISx and OISxN bits in TIMx_CR2 register can no longer be written
2: Level2: LOCK Level 1 + CC Polarity bits (CCxP/CCxNP bits in TIMx_CCER register, as long as the related channel is configured in output through the CCxS bits) as well as OSSR and OSSI bits can no longer be written
3: Level3: LOCK Level 2 + CC Control bits (OCxM and OCxPE bits in TIMx_CCMRx registers, as long as the related channel is configured in output through the CCxS bits) can no longer be written

OSSI

Bit 10: Off-state selection for Idle mode.

Allowed values:
0: Disabled: When inactive, OC/OCN outputs are disabled
1: IdleLevel: When inactive, OC/OCN outputs are forced to idle level

OSSR

Bit 11: Off-state selection for Run mode.

Allowed values:
0: Disabled: When inactive, OC/OCN outputs are disabled
1: IdleLevel: When inactive, OC/OCN outputs are enabled with their inactive level

BKE

Bit 12: Break enable.

Allowed values:
0: Disabled: Break function x disabled
1: Enabled: Break function x disabled

BKP

Bit 13: Break polarity.

Allowed values:
0: ActiveLow: Break input BRKx is active low
1: ActiveHigh: Break input BRKx is active high

AOE

Bit 14: Automatic output enable.

Allowed values:
0: Manual: MOE can be set only by software
1: Automatic: MOE can be set by software or automatically at the next update event (if none of the break inputs BRK and BRK2 is active)

MOE

Bit 15: Main output enable.

Allowed values:
0: DisabledIdle: OC/OCN are disabled or forced idle depending on OSSI
1: Enabled: OC/OCN are enabled if CCxE/CCxNE are set

BKF

Bits 16-19: Break filter.

BK2F

Bits 20-23: Break 2 filter.

BK2E

Bit 24: Break 2 enable.

Allowed values:
0: Disabled: Break function x disabled
1: Enabled: Break function x disabled

BK2P

Bit 25: Break 2 polarity.

Allowed values:
0: ActiveLow: Break input BRKx is active low
1: ActiveHigh: Break input BRKx is active high

DCR

DMA control register

Offset: 0x48, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			DBL rw								DBA rw

Toggle fields

DBA

Bits 0-4: DMA base address.

Allowed values: 0x0-0x1f

DBL

Bits 8-12: DMA burst length.

Allowed values: 0x0-0x12

DMAR

DMA address for full transfer

Offset: 0x4c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DMAB rw

Toggle fields

DMAB

Bits 0-15: DMA register for burst accesses.

CCMR3_Output

capture/compare mode register 3 (output mode)

Offset: 0x54, size: 32, reset: 0x00000000, access: read-write

4/10 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
							OC[6]M_3 rw								OC[5]M_3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OC[6]CE rw	OC[6]M rw			OC[6]PE rw	OC[6]FE rw			OC[5]CE rw	OC[5]M rw			OC[5]PE rw	OC[5]FE rw

Toggle fields

OC[5]FE

Bit 2: Output compare 5 fast enable.

OC[5]PE

Bit 3: Output compare 5 preload enable.

OC[5]M

Bits 4-6: Output compare 5 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[5]CE

Bit 7: Output compare 5 clear enable.

OC[6]FE

Bit 10: Output compare 6 fast enable.

OC[6]PE

Bit 11: Output compare 6 preload enable.

OC[6]M

Bits 12-14: Output compare 6 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[6]CE

Bit 15: Output compare 6 clear enable.

OC[5]M_3

Bit 16: Output compare 5 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

OC[6]M_3

Bit 24: Output compare 6 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

CCR5

capture/compare register

Offset: 0x58, size: 32, reset: 0x00000000, access: read-write

1/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
GC5C3 rw	GC5C2 rw	GC5C1 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

Allowed values: 0x0-0xffff

GC5C1

Bit 29: Group Channel 5 and Channel 1.

GC5C2

Bit 30: Group Channel 5 and Channel 2.

GC5C3

Bit 31: Group Channel 5 and Channel 3.

CCR6

capture/compare register

Offset: 0x5c, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

Allowed values: 0x0-0xffff

OR

option registers

Offset: 0x60, size: 32, reset: 0x00000000, access: read-write

0/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
												TIM8_ETR_ADC3_RMP rw		TIM8_ETR_ADC2_RMP rw

Toggle fields

TIM8_ETR_ADC2_RMP

Bits 0-1: TIM8_ETR_ADC2 remapping capability.

TIM8_ETR_ADC3_RMP

Bits 2-3: TIM8_ETR_ADC3 remapping capability.

TSC

0x40024000: Touch sensing controller

14/170 fields covered.

Toggle register map

Offset	Name	31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	CR	CTPH				CTPL				SSD							SSE	SSPSC	PGPSC							MCV			IODEF	SYNCPOL	AM	START	TSCE
0x4	IER																															MCEIE	EOAIE
0x8	ICR																															MCEIC	EOAIC
0xc	ISR																															MCEF	EOAF
0x10	IOHCR	G8_IO4	G8_IO3	G8_IO2	G8_IO1	G7_IO4	G7_IO3	G7_IO2	G7_IO1	G6_IO4	G6_IO3	G6_IO2	G6_IO1	G5_IO4	G5_IO3	G5_IO2	G5_IO1	G4_IO4	G4_IO3	G4_IO2	G4_IO1	G3_IO4	G3_IO3	G3_IO2	G3_IO1	G2_IO4	G2_IO3	G2_IO2	G2_IO1	G1_IO4	G1_IO3	G1_IO2	G1_IO1
0x18	IOASCR	G8_IO4	G8_IO3	G8_IO2	G8_IO1	G7_IO4	G7_IO3	G7_IO2	G7_IO1	G6_IO4	G6_IO3	G6_IO2	G6_IO1	G5_IO4	G5_IO3	G5_IO2	G5_IO1	G4_IO4	G4_IO3	G4_IO2	G4_IO1	G3_IO4	G3_IO3	G3_IO2	G3_IO1	G2_IO4	G2_IO3	G2_IO2	G2_IO1	G1_IO4	G1_IO3	G1_IO2	G1_IO1
0x20	IOSCR	G8_IO4	G8_IO3	G8_IO2	G8_IO1	G7_IO4	G7_IO3	G7_IO2	G7_IO1	G6_IO4	G6_IO3	G6_IO2	G6_IO1	G5_IO4	G5_IO3	G5_IO2	G5_IO1	G4_IO4	G4_IO3	G4_IO2	G4_IO1	G3_IO4	G3_IO3	G3_IO2	G3_IO1	G2_IO4	G2_IO3	G2_IO2	G2_IO1	G1_IO4	G1_IO3	G1_IO2	G1_IO1
0x28	IOCCR	G8_IO4	G8_IO3	G8_IO2	G8_IO1	G7_IO4	G7_IO3	G7_IO2	G7_IO1	G6_IO4	G6_IO3	G6_IO2	G6_IO1	G5_IO4	G5_IO3	G5_IO2	G5_IO1	G4_IO4	G4_IO3	G4_IO2	G4_IO1	G3_IO4	G3_IO3	G3_IO2	G3_IO1	G2_IO4	G2_IO3	G2_IO2	G2_IO1	G1_IO4	G1_IO3	G1_IO2	G1_IO1
0x30	IOGCSR									G8S	G7S	G6S	G5S	G4S	G3S	G2S	G1S									G8E	G7E	G6E	G5E	G4E	G3E	G2E	G1E
0x34	IOG[1]CR																			CNT
0x38	IOG[2]CR																			CNT
0x3c	IOG[3]CR																			CNT
0x40	IOG[4]CR																			CNT
0x44	IOG[5]CR																			CNT
0x48	IOG[6]CR																			CNT
0x4c	IOG[7]CR																			CNT
0x50	IOG[8]CR																			CNT

Toggle registers

CR

control register

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

0/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
CTPH rw				CTPL rw				SSD rw							SSE rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SSPSC rw	PGPSC rw							MCV rw			IODEF rw	SYNCPOL rw	AM rw	START rw	TSCE rw

Toggle fields

TSCE

Bit 0: Touch sensing controller enable.

START

Bit 1: Start a new acquisition.

AM

Bit 2: Acquisition mode.

SYNCPOL

Bit 3: Synchronization pin polarity.

IODEF

Bit 4: I/O Default mode.

MCV

Bits 5-7: Max count value.

PGPSC

Bits 12-14: pulse generator prescaler.

SSPSC

Bit 15: Spread spectrum prescaler.

SSE

Bit 16: Spread spectrum enable.

SSD

Bits 17-23: Spread spectrum deviation.

CTPL

Bits 24-27: Charge transfer pulse low.

CTPH

Bits 28-31: Charge transfer pulse high.

IER

interrupt enable register

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

0/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														MCEIE rw	EOAIE rw

Toggle fields

EOAIE

Bit 0: End of acquisition interrupt enable.

MCEIE

Bit 1: Max count error interrupt enable.

ICR

interrupt clear register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

0/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														MCEIC rw	EOAIC rw

Toggle fields

EOAIC

Bit 0: End of acquisition interrupt clear.

MCEIC

Bit 1: Max count error interrupt clear.

ISR

interrupt status register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

0/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														MCEF rw	EOAF rw

Toggle fields

EOAF

Bit 0: End of acquisition flag.

MCEF

Bit 1: Max count error flag.

IOHCR

I/O hysteresis control register

Offset: 0x10, size: 32, reset: 0xFFFFFFFF, access: read-write

0/32 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
G8_IO4 rw	G8_IO3 rw	G8_IO2 rw	G8_IO1 rw	G7_IO4 rw	G7_IO3 rw	G7_IO2 rw	G7_IO1 rw	G6_IO4 rw	G6_IO3 rw	G6_IO2 rw	G6_IO1 rw	G5_IO4 rw	G5_IO3 rw	G5_IO2 rw	G5_IO1 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
G4_IO4 rw	G4_IO3 rw	G4_IO2 rw	G4_IO1 rw	G3_IO4 rw	G3_IO3 rw	G3_IO2 rw	G3_IO1 rw	G2_IO4 rw	G2_IO3 rw	G2_IO2 rw	G2_IO1 rw	G1_IO4 rw	G1_IO3 rw	G1_IO2 rw	G1_IO1 rw

Toggle fields

G1_IO1

Bit 0: G1_IO1 Schmitt trigger hysteresis mode.

G1_IO2

Bit 1: G1_IO2 Schmitt trigger hysteresis mode.

G1_IO3

Bit 2: G1_IO3 Schmitt trigger hysteresis mode.

G1_IO4

Bit 3: G1_IO4 Schmitt trigger hysteresis mode.

G2_IO1

Bit 4: G2_IO1 Schmitt trigger hysteresis mode.

G2_IO2

Bit 5: G2_IO2 Schmitt trigger hysteresis mode.

G2_IO3

Bit 6: G2_IO3 Schmitt trigger hysteresis mode.

G2_IO4

Bit 7: G2_IO4 Schmitt trigger hysteresis mode.

G3_IO1

Bit 8: G3_IO1 Schmitt trigger hysteresis mode.

G3_IO2

Bit 9: G3_IO2 Schmitt trigger hysteresis mode.

G3_IO3

Bit 10: G3_IO3 Schmitt trigger hysteresis mode.

G3_IO4

Bit 11: G3_IO4 Schmitt trigger hysteresis mode.

G4_IO1

Bit 12: G4_IO1 Schmitt trigger hysteresis mode.

G4_IO2

Bit 13: G4_IO2 Schmitt trigger hysteresis mode.

G4_IO3

Bit 14: G4_IO3 Schmitt trigger hysteresis mode.

G4_IO4

Bit 15: G4_IO4 Schmitt trigger hysteresis mode.

G5_IO1

Bit 16: G5_IO1 Schmitt trigger hysteresis mode.

G5_IO2

Bit 17: G5_IO2 Schmitt trigger hysteresis mode.

G5_IO3

Bit 18: G5_IO3 Schmitt trigger hysteresis mode.

G5_IO4

Bit 19: G5_IO4 Schmitt trigger hysteresis mode.

G6_IO1

Bit 20: G6_IO1 Schmitt trigger hysteresis mode.

G6_IO2

Bit 21: G6_IO2 Schmitt trigger hysteresis mode.

G6_IO3

Bit 22: G6_IO3 Schmitt trigger hysteresis mode.

G6_IO4

Bit 23: G6_IO4 Schmitt trigger hysteresis mode.

G7_IO1

Bit 24: G7_IO1 Schmitt trigger hysteresis mode.

G7_IO2

Bit 25: G7_IO2 Schmitt trigger hysteresis mode.

G7_IO3

Bit 26: G7_IO3 Schmitt trigger hysteresis mode.

G7_IO4

Bit 27: G7_IO4 Schmitt trigger hysteresis mode.

G8_IO1

Bit 28: G8_IO1 Schmitt trigger hysteresis mode.

G8_IO2

Bit 29: G8_IO2 Schmitt trigger hysteresis mode.

G8_IO3

Bit 30: G8_IO3 Schmitt trigger hysteresis mode.

G8_IO4

Bit 31: G8_IO4 Schmitt trigger hysteresis mode.

IOASCR

I/O analog switch control register

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

0/32 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
G8_IO4 rw	G8_IO3 rw	G8_IO2 rw	G8_IO1 rw	G7_IO4 rw	G7_IO3 rw	G7_IO2 rw	G7_IO1 rw	G6_IO4 rw	G6_IO3 rw	G6_IO2 rw	G6_IO1 rw	G5_IO4 rw	G5_IO3 rw	G5_IO2 rw	G5_IO1 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
G4_IO4 rw	G4_IO3 rw	G4_IO2 rw	G4_IO1 rw	G3_IO4 rw	G3_IO3 rw	G3_IO2 rw	G3_IO1 rw	G2_IO4 rw	G2_IO3 rw	G2_IO2 rw	G2_IO1 rw	G1_IO4 rw	G1_IO3 rw	G1_IO2 rw	G1_IO1 rw

Toggle fields

G1_IO1

Bit 0: G1_IO1 analog switch enable.

G1_IO2

Bit 1: G1_IO2 analog switch enable.

G1_IO3

Bit 2: G1_IO3 analog switch enable.

G1_IO4

Bit 3: G1_IO4 analog switch enable.

G2_IO1

Bit 4: G2_IO1 analog switch enable.

G2_IO2

Bit 5: G2_IO2 analog switch enable.

G2_IO3

Bit 6: G2_IO3 analog switch enable.

G2_IO4

Bit 7: G2_IO4 analog switch enable.

G3_IO1

Bit 8: G3_IO1 analog switch enable.

G3_IO2

Bit 9: G3_IO2 analog switch enable.

G3_IO3

Bit 10: G3_IO3 analog switch enable.

G3_IO4

Bit 11: G3_IO4 analog switch enable.

G4_IO1

Bit 12: G4_IO1 analog switch enable.

G4_IO2

Bit 13: G4_IO2 analog switch enable.

G4_IO3

Bit 14: G4_IO3 analog switch enable.

G4_IO4

Bit 15: G4_IO4 analog switch enable.

G5_IO1

Bit 16: G5_IO1 analog switch enable.

G5_IO2

Bit 17: G5_IO2 analog switch enable.

G5_IO3

Bit 18: G5_IO3 analog switch enable.

G5_IO4

Bit 19: G5_IO4 analog switch enable.

G6_IO1

Bit 20: G6_IO1 analog switch enable.

G6_IO2

Bit 21: G6_IO2 analog switch enable.

G6_IO3

Bit 22: G6_IO3 analog switch enable.

G6_IO4

Bit 23: G6_IO4 analog switch enable.

G7_IO1

Bit 24: G7_IO1 analog switch enable.

G7_IO2

Bit 25: G7_IO2 analog switch enable.

G7_IO3

Bit 26: G7_IO3 analog switch enable.

G7_IO4

Bit 27: G7_IO4 analog switch enable.

G8_IO1

Bit 28: G8_IO1 analog switch enable.

G8_IO2

Bit 29: G8_IO2 analog switch enable.

G8_IO3

Bit 30: G8_IO3 analog switch enable.

G8_IO4

Bit 31: G8_IO4 analog switch enable.

IOSCR

I/O sampling control register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

0/32 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
G8_IO4 rw	G8_IO3 rw	G8_IO2 rw	G8_IO1 rw	G7_IO4 rw	G7_IO3 rw	G7_IO2 rw	G7_IO1 rw	G6_IO4 rw	G6_IO3 rw	G6_IO2 rw	G6_IO1 rw	G5_IO4 rw	G5_IO3 rw	G5_IO2 rw	G5_IO1 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
G4_IO4 rw	G4_IO3 rw	G4_IO2 rw	G4_IO1 rw	G3_IO4 rw	G3_IO3 rw	G3_IO2 rw	G3_IO1 rw	G2_IO4 rw	G2_IO3 rw	G2_IO2 rw	G2_IO1 rw	G1_IO4 rw	G1_IO3 rw	G1_IO2 rw	G1_IO1 rw

Toggle fields

G1_IO1

Bit 0: G1_IO1 sampling mode.

G1_IO2

Bit 1: G1_IO2 sampling mode.

G1_IO3

Bit 2: G1_IO3 sampling mode.

G1_IO4

Bit 3: G1_IO4 sampling mode.

G2_IO1

Bit 4: G2_IO1 sampling mode.

G2_IO2

Bit 5: G2_IO2 sampling mode.

G2_IO3

Bit 6: G2_IO3 sampling mode.

G2_IO4

Bit 7: G2_IO4 sampling mode.

G3_IO1

Bit 8: G3_IO1 sampling mode.

G3_IO2

Bit 9: G3_IO2 sampling mode.

G3_IO3

Bit 10: G3_IO3 sampling mode.

G3_IO4

Bit 11: G3_IO4 sampling mode.

G4_IO1

Bit 12: G4_IO1 sampling mode.

G4_IO2

Bit 13: G4_IO2 sampling mode.

G4_IO3

Bit 14: G4_IO3 sampling mode.

G4_IO4

Bit 15: G4_IO4 sampling mode.

G5_IO1

Bit 16: G5_IO1 sampling mode.

G5_IO2

Bit 17: G5_IO2 sampling mode.

G5_IO3

Bit 18: G5_IO3 sampling mode.

G5_IO4

Bit 19: G5_IO4 sampling mode.

G6_IO1

Bit 20: G6_IO1 sampling mode.

G6_IO2

Bit 21: G6_IO2 sampling mode.

G6_IO3

Bit 22: G6_IO3 sampling mode.

G6_IO4

Bit 23: G6_IO4 sampling mode.

G7_IO1

Bit 24: G7_IO1 sampling mode.

G7_IO2

Bit 25: G7_IO2 sampling mode.

G7_IO3

Bit 26: G7_IO3 sampling mode.

G7_IO4

Bit 27: G7_IO4 sampling mode.

G8_IO1

Bit 28: G8_IO1 sampling mode.

G8_IO2

Bit 29: G8_IO2 sampling mode.

G8_IO3

Bit 30: G8_IO3 sampling mode.

G8_IO4

Bit 31: G8_IO4 sampling mode.

IOCCR

I/O channel control register

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

0/32 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
G8_IO4 rw	G8_IO3 rw	G8_IO2 rw	G8_IO1 rw	G7_IO4 rw	G7_IO3 rw	G7_IO2 rw	G7_IO1 rw	G6_IO4 rw	G6_IO3 rw	G6_IO2 rw	G6_IO1 rw	G5_IO4 rw	G5_IO3 rw	G5_IO2 rw	G5_IO1 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
G4_IO4 rw	G4_IO3 rw	G4_IO2 rw	G4_IO1 rw	G3_IO4 rw	G3_IO3 rw	G3_IO2 rw	G3_IO1 rw	G2_IO4 rw	G2_IO3 rw	G2_IO2 rw	G2_IO1 rw	G1_IO4 rw	G1_IO3 rw	G1_IO2 rw	G1_IO1 rw

Toggle fields

G1_IO1

Bit 0: G1_IO1 channel mode.

G1_IO2

Bit 1: G1_IO2 channel mode.

G1_IO3

Bit 2: G1_IO3 channel mode.

G1_IO4

Bit 3: G1_IO4 channel mode.

G2_IO1

Bit 4: G2_IO1 channel mode.

G2_IO2

Bit 5: G2_IO2 channel mode.

G2_IO3

Bit 6: G2_IO3 channel mode.

G2_IO4

Bit 7: G2_IO4 channel mode.

G3_IO1

Bit 8: G3_IO1 channel mode.

G3_IO2

Bit 9: G3_IO2 channel mode.

G3_IO3

Bit 10: G3_IO3 channel mode.

G3_IO4

Bit 11: G3_IO4 channel mode.

G4_IO1

Bit 12: G4_IO1 channel mode.

G4_IO2

Bit 13: G4_IO2 channel mode.

G4_IO3

Bit 14: G4_IO3 channel mode.

G4_IO4

Bit 15: G4_IO4 channel mode.

G5_IO1

Bit 16: G5_IO1 channel mode.

G5_IO2

Bit 17: G5_IO2 channel mode.

G5_IO3

Bit 18: G5_IO3 channel mode.

G5_IO4

Bit 19: G5_IO4 channel mode.

G6_IO1

Bit 20: G6_IO1 channel mode.

G6_IO2

Bit 21: G6_IO2 channel mode.

G6_IO3

Bit 22: G6_IO3 channel mode.

G6_IO4

Bit 23: G6_IO4 channel mode.

G7_IO1

Bit 24: G7_IO1 channel mode.

G7_IO2

Bit 25: G7_IO2 channel mode.

G7_IO3

Bit 26: G7_IO3 channel mode.

G7_IO4

Bit 27: G7_IO4 channel mode.

G8_IO1

Bit 28: G8_IO1 channel mode.

G8_IO2

Bit 29: G8_IO2 channel mode.

G8_IO3

Bit 30: G8_IO3 channel mode.

G8_IO4

Bit 31: G8_IO4 channel mode.

IOGCSR

I/O group control status register

Offset: 0x30, size: 32, reset: 0x00000000, access: Unspecified

6/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								G8S rw	G7S rw	G6S r	G5S r	G4S r	G3S r	G2S r	G1S r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								G8E rw	G7E rw	G6E rw	G5E rw	G4E rw	G3E rw	G2E rw	G1E rw

Toggle fields

G1E

Bit 0: Analog I/O group x enable.

G2E

Bit 1: Analog I/O group x enable.

G3E

Bit 2: Analog I/O group x enable.

G4E

Bit 3: Analog I/O group x enable.

G5E

Bit 4: Analog I/O group x enable.

G6E

Bit 5: Analog I/O group x enable.

G7E

Bit 6: Analog I/O group x enable.

G8E

Bit 7: Analog I/O group x enable.

G1S

Bit 16: Analog I/O group x status.

G2S

Bit 17: Analog I/O group x status.

G3S

Bit 18: Analog I/O group x status.

G4S

Bit 19: Analog I/O group x status.

G5S

Bit 20: Analog I/O group x status.

G6S

Bit 21: Analog I/O group x status.

G7S

Bit 22: Analog I/O group x status.

G8S

Bit 23: Analog I/O group x status.

IOG[1]CR

I/O group x counter register

Offset: 0x34, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		CNT r

Toggle fields

CNT

Bits 0-13: Counter value.

IOG[2]CR

I/O group x counter register

Offset: 0x38, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		CNT r

Toggle fields

CNT

Bits 0-13: Counter value.

IOG[3]CR

I/O group x counter register

Offset: 0x3c, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		CNT r

Toggle fields

CNT

Bits 0-13: Counter value.

IOG[4]CR

I/O group x counter register

Offset: 0x40, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		CNT r

Toggle fields

CNT

Bits 0-13: Counter value.

IOG[5]CR

I/O group x counter register

Offset: 0x44, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		CNT r

Toggle fields

CNT

Bits 0-13: Counter value.

IOG[6]CR

I/O group x counter register

Offset: 0x48, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		CNT r

Toggle fields

CNT

Bits 0-13: Counter value.

IOG[7]CR

I/O group x counter register

Offset: 0x4c, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		CNT r

Toggle fields

CNT

Bits 0-13: Counter value.

IOG[8]CR

I/O group x counter register

Offset: 0x50, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		CNT r

Toggle fields

CNT

Bits 0-13: Counter value.

UART4

0x40004c00: Universal synchronous asynchronous receiver transmitter

103/103 fields covered.

Toggle register map

Offset	Name	31	27	26	25	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	CR1		EOBIE	RTOIE	DEAT				DEDT					OVER8	CMIE	MME	M	WAKE	PCE	PS	PEIE	TXEIE	TCIE	RXNEIE	IDLEIE	TE	RE	UESM	UE
0x4	CR2	ADD				RTOEN	ABRMOD		ABREN	MSBFIRST	DATAINV	TXINV	RXINV	SWAP	LINEN	STOP		CLKEN	CPOL	CPHA	LBCL		LBDIE	LBDL	ADDM7
0x8	CR3						WUFIE	WUS		SCARCNT				DEP	DEM	DDRE	OVRDIS	ONEBIT	CTSIE	CTSE	RTSE	DMAT	DMAR	SCEN	NACK	HDSEL	IRLP	IREN	EIE
0xc	BRR													BRR
0x10	GTPR													GT								PSC
0x14	RTOR	BLEN				RTO								RTO
0x18	RQR																								TXFRQ	RXFRQ	MMRQ	SBKRQ	ABRRQ
0x1c	ISR						REACK	TEACK	WUF	RWU	SBKF	CMF	BUSY	ABRF	ABRE		EOBF	RTOF	CTS	CTSIF	LBDF	TXE	TC	RXNE	IDLE	ORE	NF	FE	PE
0x20	ICR								WUCF			CMCF					EOBCF	RTOCF		CTSCF	LBDCF		TCCF		IDLECF	ORECF	NCF	FECF	PECF
0x24	RDR																				RDR
0x28	TDR																				TDR

Toggle registers

CR1

Control register 1

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

20/20 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				EOBIE rw	RTOIE rw	DEAT rw					DEDT rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OVER8 rw	CMIE rw	MME rw	M rw	WAKE rw	PCE rw	PS rw	PEIE rw	TXEIE rw	TCIE rw	RXNEIE rw	IDLEIE rw	TE rw	RE rw	UESM rw	UE rw

Toggle fields

UE

Bit 0: USART enable.

Allowed values:
0: Disabled: UART is disabled
1: Enabled: UART is enabled

UESM

Bit 1: USART enable in Stop mode.

Allowed values:
0: Disabled: USART not able to wake up the MCU from Stop mode
1: Enabled: USART able to wake up the MCU from Stop mode

RE

Bit 2: Receiver enable.

Allowed values:
0: Disabled: Receiver is disabled
1: Enabled: Receiver is enabled

TE

Bit 3: Transmitter enable.

Allowed values:
0: Disabled: Transmitter is disabled
1: Enabled: Transmitter is enabled

IDLEIE

Bit 4: IDLE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever IDLE=1 in the ISR register

RXNEIE

Bit 5: RXNE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever ORE=1 or RXNE=1 in the ISR register

TCIE

Bit 6: Transmission complete interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever TC=1 in the ISR register

TXEIE

Bit 7: interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever TXE=1 in the ISR register

PEIE

Bit 8: PE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever PE=1 in the ISR register

PS

Bit 9: Parity selection.

Allowed values:
0: Even: Even parity
1: Odd: Odd parity

PCE

Bit 10: Parity control enable.

Allowed values:
0: Disabled: Parity control disabled
1: Enabled: Parity control enabled

WAKE

Bit 11: Receiver wakeup method.

Allowed values:
0: Idle: Idle line
1: Address: Address mask

M

Bit 12: Word length.

Allowed values:
0: Bit8: 1 start bit, 8 data bits, n stop bits
1: Bit9: 1 start bit, 9 data bits, n stop bits

MME

Bit 13: Mute mode enable.

Allowed values:
0: Disabled: Receiver in active mode permanently
1: Enabled: Receiver can switch between mute mode and active mode

CMIE

Bit 14: Character match interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated when the CMF bit is set in the ISR register

OVER8

Bit 15: Oversampling mode.

Allowed values:
0: Oversampling16: Oversampling by 16
1: Oversampling8: Oversampling by 8

DEDT

Bits 16-20: Driver Enable deassertion time.

Allowed values: 0x0-0x1f

DEAT

Bits 21-25: Driver Enable assertion time.

Allowed values: 0x0-0x1f

RTOIE

Bit 26: Receiver timeout interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An USART interrupt is generated when the RTOF bit is set in the ISR register

EOBIE

Bit 27: End of Block interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: A USART interrupt is generated when the EOBF flag is set in the ISR register

CR2

Control register 2

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

18/18 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ADD rw								RTOEN rw	ABRMOD rw		ABREN rw	MSBFIRST rw	DATAINV rw	TXINV rw	RXINV rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SWAP rw	LINEN rw	STOP rw		CLKEN rw	CPOL rw	CPHA rw	LBCL rw		LBDIE rw	LBDL rw	ADDM7 rw

Toggle fields

ADDM7

Bit 4: 7-bit Address Detection/4-bit Address Detection.

Allowed values:
0: Bit4: 4-bit address detection
1: Bit7: 7-bit address detection

LBDL

Bit 5: LIN break detection length.

Allowed values:
0: Bit10: 10-bit break detection
1: Bit11: 11-bit break detection

LBDIE

Bit 6: LIN break detection interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated whenever LBDF=1 in the ISR register

LBCL

Bit 8: Last bit clock pulse.

Allowed values:
0: NotOutput: The clock pulse of the last data bit is not output to the CK pin
1: Output: The clock pulse of the last data bit is output to the CK pin

CPHA

Bit 9: Clock phase.

Allowed values:
0: First: The first clock transition is the first data capture edge
1: Second: The second clock transition is the first data capture edge

CPOL

Bit 10: Clock polarity.

Allowed values:
0: Low: Steady low value on CK pin outside transmission window
1: High: Steady high value on CK pin outside transmission window

CLKEN

Bit 11: Clock enable.

Allowed values:
0: Disabled: CK pin disabled
1: Enabled: CK pin enabled

STOP

Bits 12-13: STOP bits.

Allowed values:
0: Stop1: 1 stop bit
1: Stop0p5: 0.5 stop bit
2: Stop2: 2 stop bit
3: Stop1p5: 1.5 stop bit

LINEN

Bit 14: LIN mode enable.

Allowed values:
0: Disabled: LIN mode disabled
1: Enabled: LIN mode enabled

SWAP

Bit 15: Swap TX/RX pins.

Allowed values:
0: Standard: TX/RX pins are used as defined in standard pinout
1: Swapped: The TX and RX pins functions are swapped

RXINV

Bit 16: RX pin active level inversion.

Allowed values:
0: Standard: RX pin signal works using the standard logic levels
1: Inverted: RX pin signal values are inverted

TXINV

Bit 17: TX pin active level inversion.

Allowed values:
0: Standard: TX pin signal works using the standard logic levels
1: Inverted: TX pin signal values are inverted

DATAINV

Bit 18: Binary data inversion.

Allowed values:
0: Positive: Logical data from the data register are send/received in positive/direct logic
1: Negative: Logical data from the data register are send/received in negative/inverse logic

MSBFIRST

Bit 19: Most significant bit first.

Allowed values:
0: LSB: data is transmitted/received with data bit 0 first, following the start bit
1: MSB: data is transmitted/received with MSB (bit 7/8/9) first, following the start bit

ABREN

Bit 20: Auto baud rate enable.

Allowed values:
0: Disabled: Auto baud rate detection is disabled
1: Enabled: Auto baud rate detection is enabled

ABRMOD

Bits 21-22: Auto baud rate mode.

Allowed values:
0: Start: Measurement of the start bit is used to detect the baud rate
1: Edge: Falling edge to falling edge measurement
2: Frame7F: 0x7F frame detection
3: Frame55: 0x55 frame detection

RTOEN

Bit 23: Receiver timeout enable.

Allowed values:
0: Disabled: Receiver timeout feature disabled
1: Enabled: Receiver timeout feature enabled

ADD

Bits 24-31: Address of the USART node.

Allowed values: 0x0-0xff

CR3

Control register 3

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

19/19 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
									WUFIE rw	WUS rw		SCARCNT rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DEP rw	DEM rw	DDRE rw	OVRDIS rw	ONEBIT rw	CTSIE rw	CTSE rw	RTSE rw	DMAT rw	DMAR rw	SCEN rw	NACK rw	HDSEL rw	IRLP rw	IREN rw	EIE rw

Toggle fields

EIE

Bit 0: Error interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated when FE=1 or ORE=1 or NF=1 in the ISR register

IREN

Bit 1: IrDA mode enable.

Allowed values:
0: Disabled: IrDA disabled
1: Enabled: IrDA enabled

IRLP

Bit 2: IrDA low-power.

Allowed values:
0: Normal: Normal mode
1: LowPower: Low-power mode

HDSEL

Bit 3: Half-duplex selection.

Allowed values:
0: NotSelected: Half duplex mode is not selected
1: Selected: Half duplex mode is selected

NACK

Bit 4: Smartcard NACK enable.

Allowed values:
0: Disabled: NACK transmission in case of parity error is disabled
1: Enabled: NACK transmission during parity error is enabled

SCEN

Bit 5: Smartcard mode enable.

Allowed values:
0: Disabled: Smartcard Mode disabled
1: Enabled: Smartcard Mode enabled

DMAR

Bit 6: DMA enable receiver.

Allowed values:
0: Disabled: DMA mode is disabled for reception
1: Enabled: DMA mode is enabled for reception

DMAT

Bit 7: DMA enable transmitter.

Allowed values:
0: Disabled: DMA mode is disabled for transmission
1: Enabled: DMA mode is enabled for transmission

RTSE

Bit 8: RTS enable.

Allowed values:
0: Disabled: RTS hardware flow control disabled
1: Enabled: RTS output enabled, data is only requested when there is space in the receive buffer

CTSE

Bit 9: CTS enable.

Allowed values:
0: Disabled: CTS hardware flow control disabled
1: Enabled: CTS mode enabled, data is only transmitted when the CTS input is asserted

CTSIE

Bit 10: CTS interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated whenever CTSIF=1 in the ISR register

ONEBIT

Bit 11: One sample bit method enable.

Allowed values:
0: Sample3: Three sample bit method
1: Sample1: One sample bit method

OVRDIS

Bit 12: Overrun Disable.

Allowed values:
0: Enabled: Overrun Error Flag, ORE, is set when received data is not read before receiving new data
1: Disabled: Overrun functionality is disabled. If new data is received while the RXNE flag is still set the ORE flag is not set and the new received data overwrites the previous content of the RDR register

DDRE

Bit 13: DMA Disable on Reception Error.

Allowed values:
0: NotDisabled: DMA is not disabled in case of reception error
1: Disabled: DMA is disabled following a reception error

DEM

Bit 14: Driver enable mode.

Allowed values:
0: Disabled: DE function is disabled
1: Enabled: The DE signal is output on the RTS pin

DEP

Bit 15: Driver enable polarity selection.

Allowed values:
0: High: DE signal is active high
1: Low: DE signal is active low

SCARCNT

Bits 17-19: Smartcard auto-retry count.

Allowed values: 0x0-0x7

WUS

Bits 20-21: Wakeup from Stop mode interrupt flag selection.

Allowed values:
0: Address: WUF active on address match
2: Start: WuF active on Start bit detection
3: RXNE: WUF active on RXNE

WUFIE

Bit 22: Wakeup from Stop mode interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An USART interrupt is generated whenever WUF=1 in the ISR register

BRR

Baud rate register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BRR rw

Toggle fields

BRR

Bits 0-15: mantissa of USARTDIV.

Allowed values: 0x0-0xffff

GTPR

Guard time and prescaler register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
GT rw								PSC rw

Toggle fields

PSC

Bits 0-7: Prescaler value.

Allowed values: 0x0-0xff

GT

Bits 8-15: Guard time value.

Allowed values: 0x0-0xff

RTOR

Receiver timeout register

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BLEN rw								RTO rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RTO rw

Toggle fields

RTO

Bits 0-23: Receiver timeout value.

Allowed values: 0x0-0xffffff

BLEN

Bits 24-31: Block Length.

Allowed values: 0x0-0xff

RQR

Request register

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

5/5 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
											TXFRQ rw	RXFRQ rw	MMRQ rw	SBKRQ rw	ABRRQ rw

Toggle fields

ABRRQ

Bit 0: Auto baud rate request.

Allowed values:
1: Request: resets the ABRF flag in the USART_ISR and request an automatic baud rate measurement on the next received data frame

SBKRQ

Bit 1: Send break request.

Allowed values:
1: Break: sets the SBKF flag and request to send a BREAK on the line, as soon as the transmit machine is available

MMRQ

Bit 2: Mute mode request.

Allowed values:
1: Mute: Puts the USART in mute mode and sets the RWU flag

RXFRQ

Bit 3: Receive data flush request.

Allowed values:
1: Discard: clears the RXNE flag. This allows to discard the received data without reading it, and avoid an overrun condition

TXFRQ

Bit 4: Transmit data flush request.

Allowed values:
1: Discard: Set the TXE flags. This allows to discard the transmit data

ISR

Interrupt & status register

Offset: 0x1c, size: 32, reset: 0x000000C0, access: read-only

22/22 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
									REACK r	TEACK r	WUF r	RWU r	SBKF r	CMF r	BUSY r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ABRF r	ABRE r		EOBF r	RTOF r	CTS r	CTSIF r	LBDF r	TXE r	TC r	RXNE r	IDLE r	ORE r	NF r	FE r	PE r

Toggle fields

PE

Bit 0: Parity error.

FE

Bit 1: Framing error.

NF

Bit 2: Noise detected flag.

ORE

Bit 3: Overrun error.

IDLE

Bit 4: Idle line detected.

RXNE

Bit 5: Read data register not empty.

TC

Bit 6: Transmission complete.

TXE

Bit 7: Transmit data register empty.

LBDF

Bit 8: LIN break detection flag.

CTSIF

Bit 9: CTS interrupt flag.

CTS

Bit 10: CTS flag.

RTOF

Bit 11: Receiver timeout.

EOBF

Bit 12: End of block flag.

ABRE

Bit 14: Auto baud rate error.

ABRF

Bit 15: Auto baud rate flag.

BUSY

Bit 16: Busy flag.

CMF

Bit 17: character match flag.

SBKF

Bit 18: Send break flag.

RWU

Bit 19: Receiver wakeup from Mute mode.

WUF

Bit 20: Wakeup from Stop mode flag.

TEACK

Bit 21: Transmit enable acknowledge flag.

REACK

Bit 22: Receive enable acknowledge flag.

ICR

Interrupt flag clear register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

12/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
											WUCF rw			CMCF rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			EOBCF rw	RTOCF rw		CTSCF rw	LBDCF rw		TCCF rw		IDLECF rw	ORECF rw	NCF rw	FECF rw	PECF rw

Toggle fields

PECF

Bit 0: Parity error clear flag.

Allowed values:
1: Clear: Clears the PE flag in the ISR register

FECF

Bit 1: Framing error clear flag.

Allowed values:
1: Clear: Clears the FE flag in the ISR register

NCF

Bit 2: Noise detected clear flag.

Allowed values:
1: Clear: Clears the NF flag in the ISR register

ORECF

Bit 3: Overrun error clear flag.

Allowed values:
1: Clear: Clears the ORE flag in the ISR register

IDLECF

Bit 4: Idle line detected clear flag.

Allowed values:
1: Clear: Clears the IDLE flag in the ISR register

TCCF

Bit 6: Transmission complete clear flag.

Allowed values:
1: Clear: Clears the TC flag in the ISR register

LBDCF

Bit 8: LIN break detection clear flag.

Allowed values:
1: Clear: Clears the LBDF flag in the ISR register

CTSCF

Bit 9: CTS clear flag.

Allowed values:
1: Clear: Clears the CTSIF flag in the ISR register

RTOCF

Bit 11: Receiver timeout clear flag.

Allowed values:
1: Clear: Clears the RTOF flag in the ISR register

EOBCF

Bit 12: End of timeout clear flag.

Allowed values:
1: Clear: Clears the EOBF flag in the ISR register

CMCF

Bit 17: Character match clear flag.

Allowed values:
1: Clear: Clears the CMF flag in the ISR register

WUCF

Bit 20: Wakeup from Stop mode clear flag.

Allowed values:
1: Clear: Clears the WUF flag in the ISR register

RDR

Receive data register

Offset: 0x24, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							RDR r

Toggle fields

RDR

Bits 0-8: Receive data value.

Allowed values: 0x0-0x1ff

TDR

Transmit data register

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							TDR rw

Toggle fields

TDR

Bits 0-8: Transmit data value.

Allowed values: 0x0-0x1ff

UART5

0x40005000: Universal synchronous asynchronous receiver transmitter

103/103 fields covered.

Toggle register map

Offset	Name	31	27	26	25	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	CR1		EOBIE	RTOIE	DEAT				DEDT					OVER8	CMIE	MME	M	WAKE	PCE	PS	PEIE	TXEIE	TCIE	RXNEIE	IDLEIE	TE	RE	UESM	UE
0x4	CR2	ADD				RTOEN	ABRMOD		ABREN	MSBFIRST	DATAINV	TXINV	RXINV	SWAP	LINEN	STOP		CLKEN	CPOL	CPHA	LBCL		LBDIE	LBDL	ADDM7
0x8	CR3						WUFIE	WUS		SCARCNT				DEP	DEM	DDRE	OVRDIS	ONEBIT	CTSIE	CTSE	RTSE	DMAT	DMAR	SCEN	NACK	HDSEL	IRLP	IREN	EIE
0xc	BRR													BRR
0x10	GTPR													GT								PSC
0x14	RTOR	BLEN				RTO								RTO
0x18	RQR																								TXFRQ	RXFRQ	MMRQ	SBKRQ	ABRRQ
0x1c	ISR						REACK	TEACK	WUF	RWU	SBKF	CMF	BUSY	ABRF	ABRE		EOBF	RTOF	CTS	CTSIF	LBDF	TXE	TC	RXNE	IDLE	ORE	NF	FE	PE
0x20	ICR								WUCF			CMCF					EOBCF	RTOCF		CTSCF	LBDCF		TCCF		IDLECF	ORECF	NCF	FECF	PECF
0x24	RDR																				RDR
0x28	TDR																				TDR

Toggle registers

CR1

Control register 1

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

20/20 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				EOBIE rw	RTOIE rw	DEAT rw					DEDT rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OVER8 rw	CMIE rw	MME rw	M rw	WAKE rw	PCE rw	PS rw	PEIE rw	TXEIE rw	TCIE rw	RXNEIE rw	IDLEIE rw	TE rw	RE rw	UESM rw	UE rw

Toggle fields

UE

Bit 0: USART enable.

Allowed values:
0: Disabled: UART is disabled
1: Enabled: UART is enabled

UESM

Bit 1: USART enable in Stop mode.

Allowed values:
0: Disabled: USART not able to wake up the MCU from Stop mode
1: Enabled: USART able to wake up the MCU from Stop mode

RE

Bit 2: Receiver enable.

Allowed values:
0: Disabled: Receiver is disabled
1: Enabled: Receiver is enabled

TE

Bit 3: Transmitter enable.

Allowed values:
0: Disabled: Transmitter is disabled
1: Enabled: Transmitter is enabled

IDLEIE

Bit 4: IDLE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever IDLE=1 in the ISR register

RXNEIE

Bit 5: RXNE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever ORE=1 or RXNE=1 in the ISR register

TCIE

Bit 6: Transmission complete interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever TC=1 in the ISR register

TXEIE

Bit 7: interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever TXE=1 in the ISR register

PEIE

Bit 8: PE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever PE=1 in the ISR register

PS

Bit 9: Parity selection.

Allowed values:
0: Even: Even parity
1: Odd: Odd parity

PCE

Bit 10: Parity control enable.

Allowed values:
0: Disabled: Parity control disabled
1: Enabled: Parity control enabled

WAKE

Bit 11: Receiver wakeup method.

Allowed values:
0: Idle: Idle line
1: Address: Address mask

M

Bit 12: Word length.

Allowed values:
0: Bit8: 1 start bit, 8 data bits, n stop bits
1: Bit9: 1 start bit, 9 data bits, n stop bits

MME

Bit 13: Mute mode enable.

Allowed values:
0: Disabled: Receiver in active mode permanently
1: Enabled: Receiver can switch between mute mode and active mode

CMIE

Bit 14: Character match interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated when the CMF bit is set in the ISR register

OVER8

Bit 15: Oversampling mode.

Allowed values:
0: Oversampling16: Oversampling by 16
1: Oversampling8: Oversampling by 8

DEDT

Bits 16-20: Driver Enable deassertion time.

Allowed values: 0x0-0x1f

DEAT

Bits 21-25: Driver Enable assertion time.

Allowed values: 0x0-0x1f

RTOIE

Bit 26: Receiver timeout interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An USART interrupt is generated when the RTOF bit is set in the ISR register

EOBIE

Bit 27: End of Block interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: A USART interrupt is generated when the EOBF flag is set in the ISR register

CR2

Control register 2

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

18/18 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ADD rw								RTOEN rw	ABRMOD rw		ABREN rw	MSBFIRST rw	DATAINV rw	TXINV rw	RXINV rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SWAP rw	LINEN rw	STOP rw		CLKEN rw	CPOL rw	CPHA rw	LBCL rw		LBDIE rw	LBDL rw	ADDM7 rw

Toggle fields

ADDM7

Bit 4: 7-bit Address Detection/4-bit Address Detection.

Allowed values:
0: Bit4: 4-bit address detection
1: Bit7: 7-bit address detection

LBDL

Bit 5: LIN break detection length.

Allowed values:
0: Bit10: 10-bit break detection
1: Bit11: 11-bit break detection

LBDIE

Bit 6: LIN break detection interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated whenever LBDF=1 in the ISR register

LBCL

Bit 8: Last bit clock pulse.

Allowed values:
0: NotOutput: The clock pulse of the last data bit is not output to the CK pin
1: Output: The clock pulse of the last data bit is output to the CK pin

CPHA

Bit 9: Clock phase.

Allowed values:
0: First: The first clock transition is the first data capture edge
1: Second: The second clock transition is the first data capture edge

CPOL

Bit 10: Clock polarity.

Allowed values:
0: Low: Steady low value on CK pin outside transmission window
1: High: Steady high value on CK pin outside transmission window

CLKEN

Bit 11: Clock enable.

Allowed values:
0: Disabled: CK pin disabled
1: Enabled: CK pin enabled

STOP

Bits 12-13: STOP bits.

Allowed values:
0: Stop1: 1 stop bit
1: Stop0p5: 0.5 stop bit
2: Stop2: 2 stop bit
3: Stop1p5: 1.5 stop bit

LINEN

Bit 14: LIN mode enable.

Allowed values:
0: Disabled: LIN mode disabled
1: Enabled: LIN mode enabled

SWAP

Bit 15: Swap TX/RX pins.

Allowed values:
0: Standard: TX/RX pins are used as defined in standard pinout
1: Swapped: The TX and RX pins functions are swapped

RXINV

Bit 16: RX pin active level inversion.

Allowed values:
0: Standard: RX pin signal works using the standard logic levels
1: Inverted: RX pin signal values are inverted

TXINV

Bit 17: TX pin active level inversion.

Allowed values:
0: Standard: TX pin signal works using the standard logic levels
1: Inverted: TX pin signal values are inverted

DATAINV

Bit 18: Binary data inversion.

Allowed values:
0: Positive: Logical data from the data register are send/received in positive/direct logic
1: Negative: Logical data from the data register are send/received in negative/inverse logic

MSBFIRST

Bit 19: Most significant bit first.

Allowed values:
0: LSB: data is transmitted/received with data bit 0 first, following the start bit
1: MSB: data is transmitted/received with MSB (bit 7/8/9) first, following the start bit

ABREN

Bit 20: Auto baud rate enable.

Allowed values:
0: Disabled: Auto baud rate detection is disabled
1: Enabled: Auto baud rate detection is enabled

ABRMOD

Bits 21-22: Auto baud rate mode.

Allowed values:
0: Start: Measurement of the start bit is used to detect the baud rate
1: Edge: Falling edge to falling edge measurement
2: Frame7F: 0x7F frame detection
3: Frame55: 0x55 frame detection

RTOEN

Bit 23: Receiver timeout enable.

Allowed values:
0: Disabled: Receiver timeout feature disabled
1: Enabled: Receiver timeout feature enabled

ADD

Bits 24-31: Address of the USART node.

Allowed values: 0x0-0xff

CR3

Control register 3

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

19/19 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
									WUFIE rw	WUS rw		SCARCNT rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DEP rw	DEM rw	DDRE rw	OVRDIS rw	ONEBIT rw	CTSIE rw	CTSE rw	RTSE rw	DMAT rw	DMAR rw	SCEN rw	NACK rw	HDSEL rw	IRLP rw	IREN rw	EIE rw

Toggle fields

EIE

Bit 0: Error interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated when FE=1 or ORE=1 or NF=1 in the ISR register

IREN

Bit 1: IrDA mode enable.

Allowed values:
0: Disabled: IrDA disabled
1: Enabled: IrDA enabled

IRLP

Bit 2: IrDA low-power.

Allowed values:
0: Normal: Normal mode
1: LowPower: Low-power mode

HDSEL

Bit 3: Half-duplex selection.

Allowed values:
0: NotSelected: Half duplex mode is not selected
1: Selected: Half duplex mode is selected

NACK

Bit 4: Smartcard NACK enable.

Allowed values:
0: Disabled: NACK transmission in case of parity error is disabled
1: Enabled: NACK transmission during parity error is enabled

SCEN

Bit 5: Smartcard mode enable.

Allowed values:
0: Disabled: Smartcard Mode disabled
1: Enabled: Smartcard Mode enabled

DMAR

Bit 6: DMA enable receiver.

Allowed values:
0: Disabled: DMA mode is disabled for reception
1: Enabled: DMA mode is enabled for reception

DMAT

Bit 7: DMA enable transmitter.

Allowed values:
0: Disabled: DMA mode is disabled for transmission
1: Enabled: DMA mode is enabled for transmission

RTSE

Bit 8: RTS enable.

Allowed values:
0: Disabled: RTS hardware flow control disabled
1: Enabled: RTS output enabled, data is only requested when there is space in the receive buffer

CTSE

Bit 9: CTS enable.

Allowed values:
0: Disabled: CTS hardware flow control disabled
1: Enabled: CTS mode enabled, data is only transmitted when the CTS input is asserted

CTSIE

Bit 10: CTS interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated whenever CTSIF=1 in the ISR register

ONEBIT

Bit 11: One sample bit method enable.

Allowed values:
0: Sample3: Three sample bit method
1: Sample1: One sample bit method

OVRDIS

Bit 12: Overrun Disable.

Allowed values:
0: Enabled: Overrun Error Flag, ORE, is set when received data is not read before receiving new data
1: Disabled: Overrun functionality is disabled. If new data is received while the RXNE flag is still set the ORE flag is not set and the new received data overwrites the previous content of the RDR register

DDRE

Bit 13: DMA Disable on Reception Error.

Allowed values:
0: NotDisabled: DMA is not disabled in case of reception error
1: Disabled: DMA is disabled following a reception error

DEM

Bit 14: Driver enable mode.

Allowed values:
0: Disabled: DE function is disabled
1: Enabled: The DE signal is output on the RTS pin

DEP

Bit 15: Driver enable polarity selection.

Allowed values:
0: High: DE signal is active high
1: Low: DE signal is active low

SCARCNT

Bits 17-19: Smartcard auto-retry count.

Allowed values: 0x0-0x7

WUS

Bits 20-21: Wakeup from Stop mode interrupt flag selection.

Allowed values:
0: Address: WUF active on address match
2: Start: WuF active on Start bit detection
3: RXNE: WUF active on RXNE

WUFIE

Bit 22: Wakeup from Stop mode interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An USART interrupt is generated whenever WUF=1 in the ISR register

BRR

Baud rate register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BRR rw

Toggle fields

BRR

Bits 0-15: mantissa of USARTDIV.

Allowed values: 0x0-0xffff

GTPR

Guard time and prescaler register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
GT rw								PSC rw

Toggle fields

PSC

Bits 0-7: Prescaler value.

Allowed values: 0x0-0xff

GT

Bits 8-15: Guard time value.

Allowed values: 0x0-0xff

RTOR

Receiver timeout register

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BLEN rw								RTO rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RTO rw

Toggle fields

RTO

Bits 0-23: Receiver timeout value.

Allowed values: 0x0-0xffffff

BLEN

Bits 24-31: Block Length.

Allowed values: 0x0-0xff

RQR

Request register

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

5/5 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
											TXFRQ rw	RXFRQ rw	MMRQ rw	SBKRQ rw	ABRRQ rw

Toggle fields

ABRRQ

Bit 0: Auto baud rate request.

Allowed values:
1: Request: resets the ABRF flag in the USART_ISR and request an automatic baud rate measurement on the next received data frame

SBKRQ

Bit 1: Send break request.

Allowed values:
1: Break: sets the SBKF flag and request to send a BREAK on the line, as soon as the transmit machine is available

MMRQ

Bit 2: Mute mode request.

Allowed values:
1: Mute: Puts the USART in mute mode and sets the RWU flag

RXFRQ

Bit 3: Receive data flush request.

Allowed values:
1: Discard: clears the RXNE flag. This allows to discard the received data without reading it, and avoid an overrun condition

TXFRQ

Bit 4: Transmit data flush request.

Allowed values:
1: Discard: Set the TXE flags. This allows to discard the transmit data

ISR

Interrupt & status register

Offset: 0x1c, size: 32, reset: 0x000000C0, access: read-only

22/22 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
									REACK r	TEACK r	WUF r	RWU r	SBKF r	CMF r	BUSY r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ABRF r	ABRE r		EOBF r	RTOF r	CTS r	CTSIF r	LBDF r	TXE r	TC r	RXNE r	IDLE r	ORE r	NF r	FE r	PE r

Toggle fields

PE

Bit 0: Parity error.

FE

Bit 1: Framing error.

NF

Bit 2: Noise detected flag.

ORE

Bit 3: Overrun error.

IDLE

Bit 4: Idle line detected.

RXNE

Bit 5: Read data register not empty.

TC

Bit 6: Transmission complete.

TXE

Bit 7: Transmit data register empty.

LBDF

Bit 8: LIN break detection flag.

CTSIF

Bit 9: CTS interrupt flag.

CTS

Bit 10: CTS flag.

RTOF

Bit 11: Receiver timeout.

EOBF

Bit 12: End of block flag.

ABRE

Bit 14: Auto baud rate error.

ABRF

Bit 15: Auto baud rate flag.

BUSY

Bit 16: Busy flag.

CMF

Bit 17: character match flag.

SBKF

Bit 18: Send break flag.

RWU

Bit 19: Receiver wakeup from Mute mode.

WUF

Bit 20: Wakeup from Stop mode flag.

TEACK

Bit 21: Transmit enable acknowledge flag.

REACK

Bit 22: Receive enable acknowledge flag.

ICR

Interrupt flag clear register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

12/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
											WUCF rw			CMCF rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			EOBCF rw	RTOCF rw		CTSCF rw	LBDCF rw		TCCF rw		IDLECF rw	ORECF rw	NCF rw	FECF rw	PECF rw

Toggle fields

PECF

Bit 0: Parity error clear flag.

Allowed values:
1: Clear: Clears the PE flag in the ISR register

FECF

Bit 1: Framing error clear flag.

Allowed values:
1: Clear: Clears the FE flag in the ISR register

NCF

Bit 2: Noise detected clear flag.

Allowed values:
1: Clear: Clears the NF flag in the ISR register

ORECF

Bit 3: Overrun error clear flag.

Allowed values:
1: Clear: Clears the ORE flag in the ISR register

IDLECF

Bit 4: Idle line detected clear flag.

Allowed values:
1: Clear: Clears the IDLE flag in the ISR register

TCCF

Bit 6: Transmission complete clear flag.

Allowed values:
1: Clear: Clears the TC flag in the ISR register

LBDCF

Bit 8: LIN break detection clear flag.

Allowed values:
1: Clear: Clears the LBDF flag in the ISR register

CTSCF

Bit 9: CTS clear flag.

Allowed values:
1: Clear: Clears the CTSIF flag in the ISR register

RTOCF

Bit 11: Receiver timeout clear flag.

Allowed values:
1: Clear: Clears the RTOF flag in the ISR register

EOBCF

Bit 12: End of timeout clear flag.

Allowed values:
1: Clear: Clears the EOBF flag in the ISR register

CMCF

Bit 17: Character match clear flag.

Allowed values:
1: Clear: Clears the CMF flag in the ISR register

WUCF

Bit 20: Wakeup from Stop mode clear flag.

Allowed values:
1: Clear: Clears the WUF flag in the ISR register

RDR

Receive data register

Offset: 0x24, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							RDR r

Toggle fields

RDR

Bits 0-8: Receive data value.

Allowed values: 0x0-0x1ff

TDR

Transmit data register

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							TDR rw

Toggle fields

TDR

Bits 0-8: Transmit data value.

Allowed values: 0x0-0x1ff

USART1

0x40013800: Universal synchronous asynchronous receiver transmitter

103/103 fields covered.

Toggle register map

Offset	Name	31	27	26	25	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	CR1		EOBIE	RTOIE	DEAT				DEDT					OVER8	CMIE	MME	M	WAKE	PCE	PS	PEIE	TXEIE	TCIE	RXNEIE	IDLEIE	TE	RE	UESM	UE
0x4	CR2	ADD				RTOEN	ABRMOD		ABREN	MSBFIRST	DATAINV	TXINV	RXINV	SWAP	LINEN	STOP		CLKEN	CPOL	CPHA	LBCL		LBDIE	LBDL	ADDM7
0x8	CR3						WUFIE	WUS		SCARCNT				DEP	DEM	DDRE	OVRDIS	ONEBIT	CTSIE	CTSE	RTSE	DMAT	DMAR	SCEN	NACK	HDSEL	IRLP	IREN	EIE
0xc	BRR													BRR
0x10	GTPR													GT								PSC
0x14	RTOR	BLEN				RTO								RTO
0x18	RQR																								TXFRQ	RXFRQ	MMRQ	SBKRQ	ABRRQ
0x1c	ISR						REACK	TEACK	WUF	RWU	SBKF	CMF	BUSY	ABRF	ABRE		EOBF	RTOF	CTS	CTSIF	LBDF	TXE	TC	RXNE	IDLE	ORE	NF	FE	PE
0x20	ICR								WUCF			CMCF					EOBCF	RTOCF		CTSCF	LBDCF		TCCF		IDLECF	ORECF	NCF	FECF	PECF
0x24	RDR																				RDR
0x28	TDR																				TDR

Toggle registers

CR1

Control register 1

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

20/20 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				EOBIE rw	RTOIE rw	DEAT rw					DEDT rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OVER8 rw	CMIE rw	MME rw	M rw	WAKE rw	PCE rw	PS rw	PEIE rw	TXEIE rw	TCIE rw	RXNEIE rw	IDLEIE rw	TE rw	RE rw	UESM rw	UE rw

Toggle fields

UE

Bit 0: USART enable.

Allowed values:
0: Disabled: UART is disabled
1: Enabled: UART is enabled

UESM

Bit 1: USART enable in Stop mode.

Allowed values:
0: Disabled: USART not able to wake up the MCU from Stop mode
1: Enabled: USART able to wake up the MCU from Stop mode

RE

Bit 2: Receiver enable.

Allowed values:
0: Disabled: Receiver is disabled
1: Enabled: Receiver is enabled

TE

Bit 3: Transmitter enable.

Allowed values:
0: Disabled: Transmitter is disabled
1: Enabled: Transmitter is enabled

IDLEIE

Bit 4: IDLE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever IDLE=1 in the ISR register

RXNEIE

Bit 5: RXNE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever ORE=1 or RXNE=1 in the ISR register

TCIE

Bit 6: Transmission complete interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever TC=1 in the ISR register

TXEIE

Bit 7: interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever TXE=1 in the ISR register

PEIE

Bit 8: PE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever PE=1 in the ISR register

PS

Bit 9: Parity selection.

Allowed values:
0: Even: Even parity
1: Odd: Odd parity

PCE

Bit 10: Parity control enable.

Allowed values:
0: Disabled: Parity control disabled
1: Enabled: Parity control enabled

WAKE

Bit 11: Receiver wakeup method.

Allowed values:
0: Idle: Idle line
1: Address: Address mask

M

Bit 12: Word length.

Allowed values:
0: Bit8: 1 start bit, 8 data bits, n stop bits
1: Bit9: 1 start bit, 9 data bits, n stop bits

MME

Bit 13: Mute mode enable.

Allowed values:
0: Disabled: Receiver in active mode permanently
1: Enabled: Receiver can switch between mute mode and active mode

CMIE

Bit 14: Character match interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated when the CMF bit is set in the ISR register

OVER8

Bit 15: Oversampling mode.

Allowed values:
0: Oversampling16: Oversampling by 16
1: Oversampling8: Oversampling by 8

DEDT

Bits 16-20: Driver Enable deassertion time.

Allowed values: 0x0-0x1f

DEAT

Bits 21-25: Driver Enable assertion time.

Allowed values: 0x0-0x1f

RTOIE

Bit 26: Receiver timeout interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An USART interrupt is generated when the RTOF bit is set in the ISR register

EOBIE

Bit 27: End of Block interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: A USART interrupt is generated when the EOBF flag is set in the ISR register

CR2

Control register 2

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

18/18 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ADD rw								RTOEN rw	ABRMOD rw		ABREN rw	MSBFIRST rw	DATAINV rw	TXINV rw	RXINV rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SWAP rw	LINEN rw	STOP rw		CLKEN rw	CPOL rw	CPHA rw	LBCL rw		LBDIE rw	LBDL rw	ADDM7 rw

Toggle fields

ADDM7

Bit 4: 7-bit Address Detection/4-bit Address Detection.

Allowed values:
0: Bit4: 4-bit address detection
1: Bit7: 7-bit address detection

LBDL

Bit 5: LIN break detection length.

Allowed values:
0: Bit10: 10-bit break detection
1: Bit11: 11-bit break detection

LBDIE

Bit 6: LIN break detection interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated whenever LBDF=1 in the ISR register

LBCL

Bit 8: Last bit clock pulse.

Allowed values:
0: NotOutput: The clock pulse of the last data bit is not output to the CK pin
1: Output: The clock pulse of the last data bit is output to the CK pin

CPHA

Bit 9: Clock phase.

Allowed values:
0: First: The first clock transition is the first data capture edge
1: Second: The second clock transition is the first data capture edge

CPOL

Bit 10: Clock polarity.

Allowed values:
0: Low: Steady low value on CK pin outside transmission window
1: High: Steady high value on CK pin outside transmission window

CLKEN

Bit 11: Clock enable.

Allowed values:
0: Disabled: CK pin disabled
1: Enabled: CK pin enabled

STOP

Bits 12-13: STOP bits.

Allowed values:
0: Stop1: 1 stop bit
1: Stop0p5: 0.5 stop bit
2: Stop2: 2 stop bit
3: Stop1p5: 1.5 stop bit

LINEN

Bit 14: LIN mode enable.

Allowed values:
0: Disabled: LIN mode disabled
1: Enabled: LIN mode enabled

SWAP

Bit 15: Swap TX/RX pins.

Allowed values:
0: Standard: TX/RX pins are used as defined in standard pinout
1: Swapped: The TX and RX pins functions are swapped

RXINV

Bit 16: RX pin active level inversion.

Allowed values:
0: Standard: RX pin signal works using the standard logic levels
1: Inverted: RX pin signal values are inverted

TXINV

Bit 17: TX pin active level inversion.

Allowed values:
0: Standard: TX pin signal works using the standard logic levels
1: Inverted: TX pin signal values are inverted

DATAINV

Bit 18: Binary data inversion.

Allowed values:
0: Positive: Logical data from the data register are send/received in positive/direct logic
1: Negative: Logical data from the data register are send/received in negative/inverse logic

MSBFIRST

Bit 19: Most significant bit first.

Allowed values:
0: LSB: data is transmitted/received with data bit 0 first, following the start bit
1: MSB: data is transmitted/received with MSB (bit 7/8/9) first, following the start bit

ABREN

Bit 20: Auto baud rate enable.

Allowed values:
0: Disabled: Auto baud rate detection is disabled
1: Enabled: Auto baud rate detection is enabled

ABRMOD

Bits 21-22: Auto baud rate mode.

Allowed values:
0: Start: Measurement of the start bit is used to detect the baud rate
1: Edge: Falling edge to falling edge measurement
2: Frame7F: 0x7F frame detection
3: Frame55: 0x55 frame detection

RTOEN

Bit 23: Receiver timeout enable.

Allowed values:
0: Disabled: Receiver timeout feature disabled
1: Enabled: Receiver timeout feature enabled

ADD

Bits 24-31: Address of the USART node.

Allowed values: 0x0-0xff

CR3

Control register 3

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

19/19 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
									WUFIE rw	WUS rw		SCARCNT rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DEP rw	DEM rw	DDRE rw	OVRDIS rw	ONEBIT rw	CTSIE rw	CTSE rw	RTSE rw	DMAT rw	DMAR rw	SCEN rw	NACK rw	HDSEL rw	IRLP rw	IREN rw	EIE rw

Toggle fields

EIE

Bit 0: Error interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated when FE=1 or ORE=1 or NF=1 in the ISR register

IREN

Bit 1: IrDA mode enable.

Allowed values:
0: Disabled: IrDA disabled
1: Enabled: IrDA enabled

IRLP

Bit 2: IrDA low-power.

Allowed values:
0: Normal: Normal mode
1: LowPower: Low-power mode

HDSEL

Bit 3: Half-duplex selection.

Allowed values:
0: NotSelected: Half duplex mode is not selected
1: Selected: Half duplex mode is selected

NACK

Bit 4: Smartcard NACK enable.

Allowed values:
0: Disabled: NACK transmission in case of parity error is disabled
1: Enabled: NACK transmission during parity error is enabled

SCEN

Bit 5: Smartcard mode enable.

Allowed values:
0: Disabled: Smartcard Mode disabled
1: Enabled: Smartcard Mode enabled

DMAR

Bit 6: DMA enable receiver.

Allowed values:
0: Disabled: DMA mode is disabled for reception
1: Enabled: DMA mode is enabled for reception

DMAT

Bit 7: DMA enable transmitter.

Allowed values:
0: Disabled: DMA mode is disabled for transmission
1: Enabled: DMA mode is enabled for transmission

RTSE

Bit 8: RTS enable.

Allowed values:
0: Disabled: RTS hardware flow control disabled
1: Enabled: RTS output enabled, data is only requested when there is space in the receive buffer

CTSE

Bit 9: CTS enable.

Allowed values:
0: Disabled: CTS hardware flow control disabled
1: Enabled: CTS mode enabled, data is only transmitted when the CTS input is asserted

CTSIE

Bit 10: CTS interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated whenever CTSIF=1 in the ISR register

ONEBIT

Bit 11: One sample bit method enable.

Allowed values:
0: Sample3: Three sample bit method
1: Sample1: One sample bit method

OVRDIS

Bit 12: Overrun Disable.

Allowed values:
0: Enabled: Overrun Error Flag, ORE, is set when received data is not read before receiving new data
1: Disabled: Overrun functionality is disabled. If new data is received while the RXNE flag is still set the ORE flag is not set and the new received data overwrites the previous content of the RDR register

DDRE

Bit 13: DMA Disable on Reception Error.

Allowed values:
0: NotDisabled: DMA is not disabled in case of reception error
1: Disabled: DMA is disabled following a reception error

DEM

Bit 14: Driver enable mode.

Allowed values:
0: Disabled: DE function is disabled
1: Enabled: The DE signal is output on the RTS pin

DEP

Bit 15: Driver enable polarity selection.

Allowed values:
0: High: DE signal is active high
1: Low: DE signal is active low

SCARCNT

Bits 17-19: Smartcard auto-retry count.

Allowed values: 0x0-0x7

WUS

Bits 20-21: Wakeup from Stop mode interrupt flag selection.

Allowed values:
0: Address: WUF active on address match
2: Start: WuF active on Start bit detection
3: RXNE: WUF active on RXNE

WUFIE

Bit 22: Wakeup from Stop mode interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An USART interrupt is generated whenever WUF=1 in the ISR register

BRR

Baud rate register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BRR rw

Toggle fields

BRR

Bits 0-15: mantissa of USARTDIV.

Allowed values: 0x0-0xffff

GTPR

Guard time and prescaler register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
GT rw								PSC rw

Toggle fields

PSC

Bits 0-7: Prescaler value.

Allowed values: 0x0-0xff

GT

Bits 8-15: Guard time value.

Allowed values: 0x0-0xff

RTOR

Receiver timeout register

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BLEN rw								RTO rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RTO rw

Toggle fields

RTO

Bits 0-23: Receiver timeout value.

Allowed values: 0x0-0xffffff

BLEN

Bits 24-31: Block Length.

Allowed values: 0x0-0xff

RQR

Request register

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

5/5 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
											TXFRQ rw	RXFRQ rw	MMRQ rw	SBKRQ rw	ABRRQ rw

Toggle fields

ABRRQ

Bit 0: Auto baud rate request.

Allowed values:
1: Request: resets the ABRF flag in the USART_ISR and request an automatic baud rate measurement on the next received data frame

SBKRQ

Bit 1: Send break request.

Allowed values:
1: Break: sets the SBKF flag and request to send a BREAK on the line, as soon as the transmit machine is available

MMRQ

Bit 2: Mute mode request.

Allowed values:
1: Mute: Puts the USART in mute mode and sets the RWU flag

RXFRQ

Bit 3: Receive data flush request.

Allowed values:
1: Discard: clears the RXNE flag. This allows to discard the received data without reading it, and avoid an overrun condition

TXFRQ

Bit 4: Transmit data flush request.

Allowed values:
1: Discard: Set the TXE flags. This allows to discard the transmit data

ISR

Interrupt & status register

Offset: 0x1c, size: 32, reset: 0x000000C0, access: read-only

22/22 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
									REACK r	TEACK r	WUF r	RWU r	SBKF r	CMF r	BUSY r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ABRF r	ABRE r		EOBF r	RTOF r	CTS r	CTSIF r	LBDF r	TXE r	TC r	RXNE r	IDLE r	ORE r	NF r	FE r	PE r

Toggle fields

PE

Bit 0: Parity error.

FE

Bit 1: Framing error.

NF

Bit 2: Noise detected flag.

ORE

Bit 3: Overrun error.

IDLE

Bit 4: Idle line detected.

RXNE

Bit 5: Read data register not empty.

TC

Bit 6: Transmission complete.

TXE

Bit 7: Transmit data register empty.

LBDF

Bit 8: LIN break detection flag.

CTSIF

Bit 9: CTS interrupt flag.

CTS

Bit 10: CTS flag.

RTOF

Bit 11: Receiver timeout.

EOBF

Bit 12: End of block flag.

ABRE

Bit 14: Auto baud rate error.

ABRF

Bit 15: Auto baud rate flag.

BUSY

Bit 16: Busy flag.

CMF

Bit 17: character match flag.

SBKF

Bit 18: Send break flag.

RWU

Bit 19: Receiver wakeup from Mute mode.

WUF

Bit 20: Wakeup from Stop mode flag.

TEACK

Bit 21: Transmit enable acknowledge flag.

REACK

Bit 22: Receive enable acknowledge flag.

ICR

Interrupt flag clear register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

12/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
											WUCF rw			CMCF rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			EOBCF rw	RTOCF rw		CTSCF rw	LBDCF rw		TCCF rw		IDLECF rw	ORECF rw	NCF rw	FECF rw	PECF rw

Toggle fields

PECF

Bit 0: Parity error clear flag.

Allowed values:
1: Clear: Clears the PE flag in the ISR register

FECF

Bit 1: Framing error clear flag.

Allowed values:
1: Clear: Clears the FE flag in the ISR register

NCF

Bit 2: Noise detected clear flag.

Allowed values:
1: Clear: Clears the NF flag in the ISR register

ORECF

Bit 3: Overrun error clear flag.

Allowed values:
1: Clear: Clears the ORE flag in the ISR register

IDLECF

Bit 4: Idle line detected clear flag.

Allowed values:
1: Clear: Clears the IDLE flag in the ISR register

TCCF

Bit 6: Transmission complete clear flag.

Allowed values:
1: Clear: Clears the TC flag in the ISR register

LBDCF

Bit 8: LIN break detection clear flag.

Allowed values:
1: Clear: Clears the LBDF flag in the ISR register

CTSCF

Bit 9: CTS clear flag.

Allowed values:
1: Clear: Clears the CTSIF flag in the ISR register

RTOCF

Bit 11: Receiver timeout clear flag.

Allowed values:
1: Clear: Clears the RTOF flag in the ISR register

EOBCF

Bit 12: End of timeout clear flag.

Allowed values:
1: Clear: Clears the EOBF flag in the ISR register

CMCF

Bit 17: Character match clear flag.

Allowed values:
1: Clear: Clears the CMF flag in the ISR register

WUCF

Bit 20: Wakeup from Stop mode clear flag.

Allowed values:
1: Clear: Clears the WUF flag in the ISR register

RDR

Receive data register

Offset: 0x24, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							RDR r

Toggle fields

RDR

Bits 0-8: Receive data value.

Allowed values: 0x0-0x1ff

TDR

Transmit data register

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							TDR rw

Toggle fields

TDR

Bits 0-8: Transmit data value.

Allowed values: 0x0-0x1ff

USART2

0x40004400: Universal synchronous asynchronous receiver transmitter

103/103 fields covered.

Toggle register map

Offset	Name	31	27	26	25	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	CR1		EOBIE	RTOIE	DEAT				DEDT					OVER8	CMIE	MME	M	WAKE	PCE	PS	PEIE	TXEIE	TCIE	RXNEIE	IDLEIE	TE	RE	UESM	UE
0x4	CR2	ADD				RTOEN	ABRMOD		ABREN	MSBFIRST	DATAINV	TXINV	RXINV	SWAP	LINEN	STOP		CLKEN	CPOL	CPHA	LBCL		LBDIE	LBDL	ADDM7
0x8	CR3						WUFIE	WUS		SCARCNT				DEP	DEM	DDRE	OVRDIS	ONEBIT	CTSIE	CTSE	RTSE	DMAT	DMAR	SCEN	NACK	HDSEL	IRLP	IREN	EIE
0xc	BRR													BRR
0x10	GTPR													GT								PSC
0x14	RTOR	BLEN				RTO								RTO
0x18	RQR																								TXFRQ	RXFRQ	MMRQ	SBKRQ	ABRRQ
0x1c	ISR						REACK	TEACK	WUF	RWU	SBKF	CMF	BUSY	ABRF	ABRE		EOBF	RTOF	CTS	CTSIF	LBDF	TXE	TC	RXNE	IDLE	ORE	NF	FE	PE
0x20	ICR								WUCF			CMCF					EOBCF	RTOCF		CTSCF	LBDCF		TCCF		IDLECF	ORECF	NCF	FECF	PECF
0x24	RDR																				RDR
0x28	TDR																				TDR

Toggle registers

CR1

Control register 1

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

20/20 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				EOBIE rw	RTOIE rw	DEAT rw					DEDT rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OVER8 rw	CMIE rw	MME rw	M rw	WAKE rw	PCE rw	PS rw	PEIE rw	TXEIE rw	TCIE rw	RXNEIE rw	IDLEIE rw	TE rw	RE rw	UESM rw	UE rw

Toggle fields

UE

Bit 0: USART enable.

Allowed values:
0: Disabled: UART is disabled
1: Enabled: UART is enabled

UESM

Bit 1: USART enable in Stop mode.

Allowed values:
0: Disabled: USART not able to wake up the MCU from Stop mode
1: Enabled: USART able to wake up the MCU from Stop mode

RE

Bit 2: Receiver enable.

Allowed values:
0: Disabled: Receiver is disabled
1: Enabled: Receiver is enabled

TE

Bit 3: Transmitter enable.

Allowed values:
0: Disabled: Transmitter is disabled
1: Enabled: Transmitter is enabled

IDLEIE

Bit 4: IDLE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever IDLE=1 in the ISR register

RXNEIE

Bit 5: RXNE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever ORE=1 or RXNE=1 in the ISR register

TCIE

Bit 6: Transmission complete interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever TC=1 in the ISR register

TXEIE

Bit 7: interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever TXE=1 in the ISR register

PEIE

Bit 8: PE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever PE=1 in the ISR register

PS

Bit 9: Parity selection.

Allowed values:
0: Even: Even parity
1: Odd: Odd parity

PCE

Bit 10: Parity control enable.

Allowed values:
0: Disabled: Parity control disabled
1: Enabled: Parity control enabled

WAKE

Bit 11: Receiver wakeup method.

Allowed values:
0: Idle: Idle line
1: Address: Address mask

M

Bit 12: Word length.

Allowed values:
0: Bit8: 1 start bit, 8 data bits, n stop bits
1: Bit9: 1 start bit, 9 data bits, n stop bits

MME

Bit 13: Mute mode enable.

Allowed values:
0: Disabled: Receiver in active mode permanently
1: Enabled: Receiver can switch between mute mode and active mode

CMIE

Bit 14: Character match interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated when the CMF bit is set in the ISR register

OVER8

Bit 15: Oversampling mode.

Allowed values:
0: Oversampling16: Oversampling by 16
1: Oversampling8: Oversampling by 8

DEDT

Bits 16-20: Driver Enable deassertion time.

Allowed values: 0x0-0x1f

DEAT

Bits 21-25: Driver Enable assertion time.

Allowed values: 0x0-0x1f

RTOIE

Bit 26: Receiver timeout interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An USART interrupt is generated when the RTOF bit is set in the ISR register

EOBIE

Bit 27: End of Block interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: A USART interrupt is generated when the EOBF flag is set in the ISR register

CR2

Control register 2

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

18/18 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ADD rw								RTOEN rw	ABRMOD rw		ABREN rw	MSBFIRST rw	DATAINV rw	TXINV rw	RXINV rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SWAP rw	LINEN rw	STOP rw		CLKEN rw	CPOL rw	CPHA rw	LBCL rw		LBDIE rw	LBDL rw	ADDM7 rw

Toggle fields

ADDM7

Bit 4: 7-bit Address Detection/4-bit Address Detection.

Allowed values:
0: Bit4: 4-bit address detection
1: Bit7: 7-bit address detection

LBDL

Bit 5: LIN break detection length.

Allowed values:
0: Bit10: 10-bit break detection
1: Bit11: 11-bit break detection

LBDIE

Bit 6: LIN break detection interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated whenever LBDF=1 in the ISR register

LBCL

Bit 8: Last bit clock pulse.

Allowed values:
0: NotOutput: The clock pulse of the last data bit is not output to the CK pin
1: Output: The clock pulse of the last data bit is output to the CK pin

CPHA

Bit 9: Clock phase.

Allowed values:
0: First: The first clock transition is the first data capture edge
1: Second: The second clock transition is the first data capture edge

CPOL

Bit 10: Clock polarity.

Allowed values:
0: Low: Steady low value on CK pin outside transmission window
1: High: Steady high value on CK pin outside transmission window

CLKEN

Bit 11: Clock enable.

Allowed values:
0: Disabled: CK pin disabled
1: Enabled: CK pin enabled

STOP

Bits 12-13: STOP bits.

Allowed values:
0: Stop1: 1 stop bit
1: Stop0p5: 0.5 stop bit
2: Stop2: 2 stop bit
3: Stop1p5: 1.5 stop bit

LINEN

Bit 14: LIN mode enable.

Allowed values:
0: Disabled: LIN mode disabled
1: Enabled: LIN mode enabled

SWAP

Bit 15: Swap TX/RX pins.

Allowed values:
0: Standard: TX/RX pins are used as defined in standard pinout
1: Swapped: The TX and RX pins functions are swapped

RXINV

Bit 16: RX pin active level inversion.

Allowed values:
0: Standard: RX pin signal works using the standard logic levels
1: Inverted: RX pin signal values are inverted

TXINV

Bit 17: TX pin active level inversion.

Allowed values:
0: Standard: TX pin signal works using the standard logic levels
1: Inverted: TX pin signal values are inverted

DATAINV

Bit 18: Binary data inversion.

Allowed values:
0: Positive: Logical data from the data register are send/received in positive/direct logic
1: Negative: Logical data from the data register are send/received in negative/inverse logic

MSBFIRST

Bit 19: Most significant bit first.

Allowed values:
0: LSB: data is transmitted/received with data bit 0 first, following the start bit
1: MSB: data is transmitted/received with MSB (bit 7/8/9) first, following the start bit

ABREN

Bit 20: Auto baud rate enable.

Allowed values:
0: Disabled: Auto baud rate detection is disabled
1: Enabled: Auto baud rate detection is enabled

ABRMOD

Bits 21-22: Auto baud rate mode.

Allowed values:
0: Start: Measurement of the start bit is used to detect the baud rate
1: Edge: Falling edge to falling edge measurement
2: Frame7F: 0x7F frame detection
3: Frame55: 0x55 frame detection

RTOEN

Bit 23: Receiver timeout enable.

Allowed values:
0: Disabled: Receiver timeout feature disabled
1: Enabled: Receiver timeout feature enabled

ADD

Bits 24-31: Address of the USART node.

Allowed values: 0x0-0xff

CR3

Control register 3

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

19/19 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
									WUFIE rw	WUS rw		SCARCNT rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DEP rw	DEM rw	DDRE rw	OVRDIS rw	ONEBIT rw	CTSIE rw	CTSE rw	RTSE rw	DMAT rw	DMAR rw	SCEN rw	NACK rw	HDSEL rw	IRLP rw	IREN rw	EIE rw

Toggle fields

EIE

Bit 0: Error interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated when FE=1 or ORE=1 or NF=1 in the ISR register

IREN

Bit 1: IrDA mode enable.

Allowed values:
0: Disabled: IrDA disabled
1: Enabled: IrDA enabled

IRLP

Bit 2: IrDA low-power.

Allowed values:
0: Normal: Normal mode
1: LowPower: Low-power mode

HDSEL

Bit 3: Half-duplex selection.

Allowed values:
0: NotSelected: Half duplex mode is not selected
1: Selected: Half duplex mode is selected

NACK

Bit 4: Smartcard NACK enable.

Allowed values:
0: Disabled: NACK transmission in case of parity error is disabled
1: Enabled: NACK transmission during parity error is enabled

SCEN

Bit 5: Smartcard mode enable.

Allowed values:
0: Disabled: Smartcard Mode disabled
1: Enabled: Smartcard Mode enabled

DMAR

Bit 6: DMA enable receiver.

Allowed values:
0: Disabled: DMA mode is disabled for reception
1: Enabled: DMA mode is enabled for reception

DMAT

Bit 7: DMA enable transmitter.

Allowed values:
0: Disabled: DMA mode is disabled for transmission
1: Enabled: DMA mode is enabled for transmission

RTSE

Bit 8: RTS enable.

Allowed values:
0: Disabled: RTS hardware flow control disabled
1: Enabled: RTS output enabled, data is only requested when there is space in the receive buffer

CTSE

Bit 9: CTS enable.

Allowed values:
0: Disabled: CTS hardware flow control disabled
1: Enabled: CTS mode enabled, data is only transmitted when the CTS input is asserted

CTSIE

Bit 10: CTS interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated whenever CTSIF=1 in the ISR register

ONEBIT

Bit 11: One sample bit method enable.

Allowed values:
0: Sample3: Three sample bit method
1: Sample1: One sample bit method

OVRDIS

Bit 12: Overrun Disable.

Allowed values:
0: Enabled: Overrun Error Flag, ORE, is set when received data is not read before receiving new data
1: Disabled: Overrun functionality is disabled. If new data is received while the RXNE flag is still set the ORE flag is not set and the new received data overwrites the previous content of the RDR register

DDRE

Bit 13: DMA Disable on Reception Error.

Allowed values:
0: NotDisabled: DMA is not disabled in case of reception error
1: Disabled: DMA is disabled following a reception error

DEM

Bit 14: Driver enable mode.

Allowed values:
0: Disabled: DE function is disabled
1: Enabled: The DE signal is output on the RTS pin

DEP

Bit 15: Driver enable polarity selection.

Allowed values:
0: High: DE signal is active high
1: Low: DE signal is active low

SCARCNT

Bits 17-19: Smartcard auto-retry count.

Allowed values: 0x0-0x7

WUS

Bits 20-21: Wakeup from Stop mode interrupt flag selection.

Allowed values:
0: Address: WUF active on address match
2: Start: WuF active on Start bit detection
3: RXNE: WUF active on RXNE

WUFIE

Bit 22: Wakeup from Stop mode interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An USART interrupt is generated whenever WUF=1 in the ISR register

BRR

Baud rate register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BRR rw

Toggle fields

BRR

Bits 0-15: mantissa of USARTDIV.

Allowed values: 0x0-0xffff

GTPR

Guard time and prescaler register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
GT rw								PSC rw

Toggle fields

PSC

Bits 0-7: Prescaler value.

Allowed values: 0x0-0xff

GT

Bits 8-15: Guard time value.

Allowed values: 0x0-0xff

RTOR

Receiver timeout register

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BLEN rw								RTO rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RTO rw

Toggle fields

RTO

Bits 0-23: Receiver timeout value.

Allowed values: 0x0-0xffffff

BLEN

Bits 24-31: Block Length.

Allowed values: 0x0-0xff

RQR

Request register

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

5/5 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
											TXFRQ rw	RXFRQ rw	MMRQ rw	SBKRQ rw	ABRRQ rw

Toggle fields

ABRRQ

Bit 0: Auto baud rate request.

Allowed values:
1: Request: resets the ABRF flag in the USART_ISR and request an automatic baud rate measurement on the next received data frame

SBKRQ

Bit 1: Send break request.

Allowed values:
1: Break: sets the SBKF flag and request to send a BREAK on the line, as soon as the transmit machine is available

MMRQ

Bit 2: Mute mode request.

Allowed values:
1: Mute: Puts the USART in mute mode and sets the RWU flag

RXFRQ

Bit 3: Receive data flush request.

Allowed values:
1: Discard: clears the RXNE flag. This allows to discard the received data without reading it, and avoid an overrun condition

TXFRQ

Bit 4: Transmit data flush request.

Allowed values:
1: Discard: Set the TXE flags. This allows to discard the transmit data

ISR

Interrupt & status register

Offset: 0x1c, size: 32, reset: 0x000000C0, access: read-only

22/22 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
									REACK r	TEACK r	WUF r	RWU r	SBKF r	CMF r	BUSY r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ABRF r	ABRE r		EOBF r	RTOF r	CTS r	CTSIF r	LBDF r	TXE r	TC r	RXNE r	IDLE r	ORE r	NF r	FE r	PE r

Toggle fields

PE

Bit 0: Parity error.

FE

Bit 1: Framing error.

NF

Bit 2: Noise detected flag.

ORE

Bit 3: Overrun error.

IDLE

Bit 4: Idle line detected.

RXNE

Bit 5: Read data register not empty.

TC

Bit 6: Transmission complete.

TXE

Bit 7: Transmit data register empty.

LBDF

Bit 8: LIN break detection flag.

CTSIF

Bit 9: CTS interrupt flag.

CTS

Bit 10: CTS flag.

RTOF

Bit 11: Receiver timeout.

EOBF

Bit 12: End of block flag.

ABRE

Bit 14: Auto baud rate error.

ABRF

Bit 15: Auto baud rate flag.

BUSY

Bit 16: Busy flag.

CMF

Bit 17: character match flag.

SBKF

Bit 18: Send break flag.

RWU

Bit 19: Receiver wakeup from Mute mode.

WUF

Bit 20: Wakeup from Stop mode flag.

TEACK

Bit 21: Transmit enable acknowledge flag.

REACK

Bit 22: Receive enable acknowledge flag.

ICR

Interrupt flag clear register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

12/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
											WUCF rw			CMCF rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			EOBCF rw	RTOCF rw		CTSCF rw	LBDCF rw		TCCF rw		IDLECF rw	ORECF rw	NCF rw	FECF rw	PECF rw

Toggle fields

PECF

Bit 0: Parity error clear flag.

Allowed values:
1: Clear: Clears the PE flag in the ISR register

FECF

Bit 1: Framing error clear flag.

Allowed values:
1: Clear: Clears the FE flag in the ISR register

NCF

Bit 2: Noise detected clear flag.

Allowed values:
1: Clear: Clears the NF flag in the ISR register

ORECF

Bit 3: Overrun error clear flag.

Allowed values:
1: Clear: Clears the ORE flag in the ISR register

IDLECF

Bit 4: Idle line detected clear flag.

Allowed values:
1: Clear: Clears the IDLE flag in the ISR register

TCCF

Bit 6: Transmission complete clear flag.

Allowed values:
1: Clear: Clears the TC flag in the ISR register

LBDCF

Bit 8: LIN break detection clear flag.

Allowed values:
1: Clear: Clears the LBDF flag in the ISR register

CTSCF

Bit 9: CTS clear flag.

Allowed values:
1: Clear: Clears the CTSIF flag in the ISR register

RTOCF

Bit 11: Receiver timeout clear flag.

Allowed values:
1: Clear: Clears the RTOF flag in the ISR register

EOBCF

Bit 12: End of timeout clear flag.

Allowed values:
1: Clear: Clears the EOBF flag in the ISR register

CMCF

Bit 17: Character match clear flag.

Allowed values:
1: Clear: Clears the CMF flag in the ISR register

WUCF

Bit 20: Wakeup from Stop mode clear flag.

Allowed values:
1: Clear: Clears the WUF flag in the ISR register

RDR

Receive data register

Offset: 0x24, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							RDR r

Toggle fields

RDR

Bits 0-8: Receive data value.

Allowed values: 0x0-0x1ff

TDR

Transmit data register

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							TDR rw

Toggle fields

TDR

Bits 0-8: Transmit data value.

Allowed values: 0x0-0x1ff

USART3

0x40004800: Universal synchronous asynchronous receiver transmitter

103/103 fields covered.

Toggle register map

Offset	Name	31	27	26	25	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	CR1		EOBIE	RTOIE	DEAT				DEDT					OVER8	CMIE	MME	M	WAKE	PCE	PS	PEIE	TXEIE	TCIE	RXNEIE	IDLEIE	TE	RE	UESM	UE
0x4	CR2	ADD				RTOEN	ABRMOD		ABREN	MSBFIRST	DATAINV	TXINV	RXINV	SWAP	LINEN	STOP		CLKEN	CPOL	CPHA	LBCL		LBDIE	LBDL	ADDM7
0x8	CR3						WUFIE	WUS		SCARCNT				DEP	DEM	DDRE	OVRDIS	ONEBIT	CTSIE	CTSE	RTSE	DMAT	DMAR	SCEN	NACK	HDSEL	IRLP	IREN	EIE
0xc	BRR													BRR
0x10	GTPR													GT								PSC
0x14	RTOR	BLEN				RTO								RTO
0x18	RQR																								TXFRQ	RXFRQ	MMRQ	SBKRQ	ABRRQ
0x1c	ISR						REACK	TEACK	WUF	RWU	SBKF	CMF	BUSY	ABRF	ABRE		EOBF	RTOF	CTS	CTSIF	LBDF	TXE	TC	RXNE	IDLE	ORE	NF	FE	PE
0x20	ICR								WUCF			CMCF					EOBCF	RTOCF		CTSCF	LBDCF		TCCF		IDLECF	ORECF	NCF	FECF	PECF
0x24	RDR																				RDR
0x28	TDR																				TDR

Toggle registers

CR1

Control register 1

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

20/20 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				EOBIE rw	RTOIE rw	DEAT rw					DEDT rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OVER8 rw	CMIE rw	MME rw	M rw	WAKE rw	PCE rw	PS rw	PEIE rw	TXEIE rw	TCIE rw	RXNEIE rw	IDLEIE rw	TE rw	RE rw	UESM rw	UE rw

Toggle fields

UE

Bit 0: USART enable.

Allowed values:
0: Disabled: UART is disabled
1: Enabled: UART is enabled

UESM

Bit 1: USART enable in Stop mode.

Allowed values:
0: Disabled: USART not able to wake up the MCU from Stop mode
1: Enabled: USART able to wake up the MCU from Stop mode

RE

Bit 2: Receiver enable.

Allowed values:
0: Disabled: Receiver is disabled
1: Enabled: Receiver is enabled

TE

Bit 3: Transmitter enable.

Allowed values:
0: Disabled: Transmitter is disabled
1: Enabled: Transmitter is enabled

IDLEIE

Bit 4: IDLE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever IDLE=1 in the ISR register

RXNEIE

Bit 5: RXNE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever ORE=1 or RXNE=1 in the ISR register

TCIE

Bit 6: Transmission complete interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever TC=1 in the ISR register

TXEIE

Bit 7: interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever TXE=1 in the ISR register

PEIE

Bit 8: PE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever PE=1 in the ISR register

PS

Bit 9: Parity selection.

Allowed values:
0: Even: Even parity
1: Odd: Odd parity

PCE

Bit 10: Parity control enable.

Allowed values:
0: Disabled: Parity control disabled
1: Enabled: Parity control enabled

WAKE

Bit 11: Receiver wakeup method.

Allowed values:
0: Idle: Idle line
1: Address: Address mask

M

Bit 12: Word length.

Allowed values:
0: Bit8: 1 start bit, 8 data bits, n stop bits
1: Bit9: 1 start bit, 9 data bits, n stop bits

MME

Bit 13: Mute mode enable.

Allowed values:
0: Disabled: Receiver in active mode permanently
1: Enabled: Receiver can switch between mute mode and active mode

CMIE

Bit 14: Character match interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated when the CMF bit is set in the ISR register

OVER8

Bit 15: Oversampling mode.

Allowed values:
0: Oversampling16: Oversampling by 16
1: Oversampling8: Oversampling by 8

DEDT

Bits 16-20: Driver Enable deassertion time.

Allowed values: 0x0-0x1f

DEAT

Bits 21-25: Driver Enable assertion time.

Allowed values: 0x0-0x1f

RTOIE

Bit 26: Receiver timeout interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An USART interrupt is generated when the RTOF bit is set in the ISR register

EOBIE

Bit 27: End of Block interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: A USART interrupt is generated when the EOBF flag is set in the ISR register

CR2

Control register 2

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

18/18 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ADD rw								RTOEN rw	ABRMOD rw		ABREN rw	MSBFIRST rw	DATAINV rw	TXINV rw	RXINV rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SWAP rw	LINEN rw	STOP rw		CLKEN rw	CPOL rw	CPHA rw	LBCL rw		LBDIE rw	LBDL rw	ADDM7 rw

Toggle fields

ADDM7

Bit 4: 7-bit Address Detection/4-bit Address Detection.

Allowed values:
0: Bit4: 4-bit address detection
1: Bit7: 7-bit address detection

LBDL

Bit 5: LIN break detection length.

Allowed values:
0: Bit10: 10-bit break detection
1: Bit11: 11-bit break detection

LBDIE

Bit 6: LIN break detection interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated whenever LBDF=1 in the ISR register

LBCL

Bit 8: Last bit clock pulse.

Allowed values:
0: NotOutput: The clock pulse of the last data bit is not output to the CK pin
1: Output: The clock pulse of the last data bit is output to the CK pin

CPHA

Bit 9: Clock phase.

Allowed values:
0: First: The first clock transition is the first data capture edge
1: Second: The second clock transition is the first data capture edge

CPOL

Bit 10: Clock polarity.

Allowed values:
0: Low: Steady low value on CK pin outside transmission window
1: High: Steady high value on CK pin outside transmission window

CLKEN

Bit 11: Clock enable.

Allowed values:
0: Disabled: CK pin disabled
1: Enabled: CK pin enabled

STOP

Bits 12-13: STOP bits.

Allowed values:
0: Stop1: 1 stop bit
1: Stop0p5: 0.5 stop bit
2: Stop2: 2 stop bit
3: Stop1p5: 1.5 stop bit

LINEN

Bit 14: LIN mode enable.

Allowed values:
0: Disabled: LIN mode disabled
1: Enabled: LIN mode enabled

SWAP

Bit 15: Swap TX/RX pins.

Allowed values:
0: Standard: TX/RX pins are used as defined in standard pinout
1: Swapped: The TX and RX pins functions are swapped

RXINV

Bit 16: RX pin active level inversion.

Allowed values:
0: Standard: RX pin signal works using the standard logic levels
1: Inverted: RX pin signal values are inverted

TXINV

Bit 17: TX pin active level inversion.

Allowed values:
0: Standard: TX pin signal works using the standard logic levels
1: Inverted: TX pin signal values are inverted

DATAINV

Bit 18: Binary data inversion.

Allowed values:
0: Positive: Logical data from the data register are send/received in positive/direct logic
1: Negative: Logical data from the data register are send/received in negative/inverse logic

MSBFIRST

Bit 19: Most significant bit first.

Allowed values:
0: LSB: data is transmitted/received with data bit 0 first, following the start bit
1: MSB: data is transmitted/received with MSB (bit 7/8/9) first, following the start bit

ABREN

Bit 20: Auto baud rate enable.

Allowed values:
0: Disabled: Auto baud rate detection is disabled
1: Enabled: Auto baud rate detection is enabled

ABRMOD

Bits 21-22: Auto baud rate mode.

Allowed values:
0: Start: Measurement of the start bit is used to detect the baud rate
1: Edge: Falling edge to falling edge measurement
2: Frame7F: 0x7F frame detection
3: Frame55: 0x55 frame detection

RTOEN

Bit 23: Receiver timeout enable.

Allowed values:
0: Disabled: Receiver timeout feature disabled
1: Enabled: Receiver timeout feature enabled

ADD

Bits 24-31: Address of the USART node.

Allowed values: 0x0-0xff

CR3

Control register 3

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

19/19 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
									WUFIE rw	WUS rw		SCARCNT rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DEP rw	DEM rw	DDRE rw	OVRDIS rw	ONEBIT rw	CTSIE rw	CTSE rw	RTSE rw	DMAT rw	DMAR rw	SCEN rw	NACK rw	HDSEL rw	IRLP rw	IREN rw	EIE rw

Toggle fields

EIE

Bit 0: Error interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated when FE=1 or ORE=1 or NF=1 in the ISR register

IREN

Bit 1: IrDA mode enable.

Allowed values:
0: Disabled: IrDA disabled
1: Enabled: IrDA enabled

IRLP

Bit 2: IrDA low-power.

Allowed values:
0: Normal: Normal mode
1: LowPower: Low-power mode

HDSEL

Bit 3: Half-duplex selection.

Allowed values:
0: NotSelected: Half duplex mode is not selected
1: Selected: Half duplex mode is selected

NACK

Bit 4: Smartcard NACK enable.

Allowed values:
0: Disabled: NACK transmission in case of parity error is disabled
1: Enabled: NACK transmission during parity error is enabled

SCEN

Bit 5: Smartcard mode enable.

Allowed values:
0: Disabled: Smartcard Mode disabled
1: Enabled: Smartcard Mode enabled

DMAR

Bit 6: DMA enable receiver.

Allowed values:
0: Disabled: DMA mode is disabled for reception
1: Enabled: DMA mode is enabled for reception

DMAT

Bit 7: DMA enable transmitter.

Allowed values:
0: Disabled: DMA mode is disabled for transmission
1: Enabled: DMA mode is enabled for transmission

RTSE

Bit 8: RTS enable.

Allowed values:
0: Disabled: RTS hardware flow control disabled
1: Enabled: RTS output enabled, data is only requested when there is space in the receive buffer

CTSE

Bit 9: CTS enable.

Allowed values:
0: Disabled: CTS hardware flow control disabled
1: Enabled: CTS mode enabled, data is only transmitted when the CTS input is asserted

CTSIE

Bit 10: CTS interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated whenever CTSIF=1 in the ISR register

ONEBIT

Bit 11: One sample bit method enable.

Allowed values:
0: Sample3: Three sample bit method
1: Sample1: One sample bit method

OVRDIS

Bit 12: Overrun Disable.

Allowed values:
0: Enabled: Overrun Error Flag, ORE, is set when received data is not read before receiving new data
1: Disabled: Overrun functionality is disabled. If new data is received while the RXNE flag is still set the ORE flag is not set and the new received data overwrites the previous content of the RDR register

DDRE

Bit 13: DMA Disable on Reception Error.

Allowed values:
0: NotDisabled: DMA is not disabled in case of reception error
1: Disabled: DMA is disabled following a reception error

DEM

Bit 14: Driver enable mode.

Allowed values:
0: Disabled: DE function is disabled
1: Enabled: The DE signal is output on the RTS pin

DEP

Bit 15: Driver enable polarity selection.

Allowed values:
0: High: DE signal is active high
1: Low: DE signal is active low

SCARCNT

Bits 17-19: Smartcard auto-retry count.

Allowed values: 0x0-0x7

WUS

Bits 20-21: Wakeup from Stop mode interrupt flag selection.

Allowed values:
0: Address: WUF active on address match
2: Start: WuF active on Start bit detection
3: RXNE: WUF active on RXNE

WUFIE

Bit 22: Wakeup from Stop mode interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An USART interrupt is generated whenever WUF=1 in the ISR register

BRR

Baud rate register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BRR rw

Toggle fields

BRR

Bits 0-15: mantissa of USARTDIV.

Allowed values: 0x0-0xffff

GTPR

Guard time and prescaler register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
GT rw								PSC rw

Toggle fields

PSC

Bits 0-7: Prescaler value.

Allowed values: 0x0-0xff

GT

Bits 8-15: Guard time value.

Allowed values: 0x0-0xff

RTOR

Receiver timeout register

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BLEN rw								RTO rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RTO rw

Toggle fields

RTO

Bits 0-23: Receiver timeout value.

Allowed values: 0x0-0xffffff

BLEN

Bits 24-31: Block Length.

Allowed values: 0x0-0xff

RQR

Request register

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

5/5 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
											TXFRQ rw	RXFRQ rw	MMRQ rw	SBKRQ rw	ABRRQ rw

Toggle fields

ABRRQ

Bit 0: Auto baud rate request.

Allowed values:
1: Request: resets the ABRF flag in the USART_ISR and request an automatic baud rate measurement on the next received data frame

SBKRQ

Bit 1: Send break request.

Allowed values:
1: Break: sets the SBKF flag and request to send a BREAK on the line, as soon as the transmit machine is available

MMRQ

Bit 2: Mute mode request.

Allowed values:
1: Mute: Puts the USART in mute mode and sets the RWU flag

RXFRQ

Bit 3: Receive data flush request.

Allowed values:
1: Discard: clears the RXNE flag. This allows to discard the received data without reading it, and avoid an overrun condition

TXFRQ

Bit 4: Transmit data flush request.

Allowed values:
1: Discard: Set the TXE flags. This allows to discard the transmit data

ISR

Interrupt & status register

Offset: 0x1c, size: 32, reset: 0x000000C0, access: read-only

22/22 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
									REACK r	TEACK r	WUF r	RWU r	SBKF r	CMF r	BUSY r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ABRF r	ABRE r		EOBF r	RTOF r	CTS r	CTSIF r	LBDF r	TXE r	TC r	RXNE r	IDLE r	ORE r	NF r	FE r	PE r

Toggle fields

PE

Bit 0: Parity error.

FE

Bit 1: Framing error.

NF

Bit 2: Noise detected flag.

ORE

Bit 3: Overrun error.

IDLE

Bit 4: Idle line detected.

RXNE

Bit 5: Read data register not empty.

TC

Bit 6: Transmission complete.

TXE

Bit 7: Transmit data register empty.

LBDF

Bit 8: LIN break detection flag.

CTSIF

Bit 9: CTS interrupt flag.

CTS

Bit 10: CTS flag.

RTOF

Bit 11: Receiver timeout.

EOBF

Bit 12: End of block flag.

ABRE

Bit 14: Auto baud rate error.

ABRF

Bit 15: Auto baud rate flag.

BUSY

Bit 16: Busy flag.

CMF

Bit 17: character match flag.

SBKF

Bit 18: Send break flag.

RWU

Bit 19: Receiver wakeup from Mute mode.

WUF

Bit 20: Wakeup from Stop mode flag.

TEACK

Bit 21: Transmit enable acknowledge flag.

REACK

Bit 22: Receive enable acknowledge flag.

ICR

Interrupt flag clear register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

12/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
											WUCF rw			CMCF rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			EOBCF rw	RTOCF rw		CTSCF rw	LBDCF rw		TCCF rw		IDLECF rw	ORECF rw	NCF rw	FECF rw	PECF rw

Toggle fields

PECF

Bit 0: Parity error clear flag.

Allowed values:
1: Clear: Clears the PE flag in the ISR register

FECF

Bit 1: Framing error clear flag.

Allowed values:
1: Clear: Clears the FE flag in the ISR register

NCF

Bit 2: Noise detected clear flag.

Allowed values:
1: Clear: Clears the NF flag in the ISR register

ORECF

Bit 3: Overrun error clear flag.

Allowed values:
1: Clear: Clears the ORE flag in the ISR register

IDLECF

Bit 4: Idle line detected clear flag.

Allowed values:
1: Clear: Clears the IDLE flag in the ISR register

TCCF

Bit 6: Transmission complete clear flag.

Allowed values:
1: Clear: Clears the TC flag in the ISR register

LBDCF

Bit 8: LIN break detection clear flag.

Allowed values:
1: Clear: Clears the LBDF flag in the ISR register

CTSCF

Bit 9: CTS clear flag.

Allowed values:
1: Clear: Clears the CTSIF flag in the ISR register

RTOCF

Bit 11: Receiver timeout clear flag.

Allowed values:
1: Clear: Clears the RTOF flag in the ISR register

EOBCF

Bit 12: End of timeout clear flag.

Allowed values:
1: Clear: Clears the EOBF flag in the ISR register

CMCF

Bit 17: Character match clear flag.

Allowed values:
1: Clear: Clears the CMF flag in the ISR register

WUCF

Bit 20: Wakeup from Stop mode clear flag.

Allowed values:
1: Clear: Clears the WUF flag in the ISR register

RDR

Receive data register

Offset: 0x24, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							RDR r

Toggle fields

RDR

Bits 0-8: Receive data value.

Allowed values: 0x0-0x1ff

TDR

Transmit data register

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							TDR rw

Toggle fields

TDR

Bits 0-8: Transmit data value.

Allowed values: 0x0-0x1ff

USB

0x40005c00: Universal serial bus full-speed device interface

71/111 fields covered.

Toggle register map

Offset	Name	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	EP0R	CTR_RX	DTOG_RX	STAT_RX		SETUP	EP_TYPE		EP_KIND	CTR_TX	DTOG_TX	STAT_TX		EA
0x4	EP1R	CTR_RX	DTOG_RX	STAT_RX		SETUP	EP_TYPE		EP_KIND	CTR_TX	DTOG_TX	STAT_TX		EA
0x8	EP2R	CTR_RX	DTOG_RX	STAT_RX		SETUP	EP_TYPE		EP_KIND	CTR_TX	DTOG_TX	STAT_TX		EA
0xc	EP3R	CTR_RX	DTOG_RX	STAT_RX		SETUP	EP_TYPE		EP_KIND	CTR_TX	DTOG_TX	STAT_TX		EA
0x10	EP4R	CTR_RX	DTOG_RX	STAT_RX		SETUP	EP_TYPE		EP_KIND	CTR_TX	DTOG_TX	STAT_TX		EA
0x14	EP5R	CTR_RX	DTOG_RX	STAT_RX		SETUP	EP_TYPE		EP_KIND	CTR_TX	DTOG_TX	STAT_TX		EA
0x18	EP6R	CTR_RX	DTOG_RX	STAT_RX		SETUP	EP_TYPE		EP_KIND	CTR_TX	DTOG_TX	STAT_TX		EA
0x1c	EP7R	CTR_RX	DTOG_RX	STAT_RX		SETUP	EP_TYPE		EP_KIND	CTR_TX	DTOG_TX	STAT_TX		EA
0x40	CNTR	CTRM	PMAOVRM	ERRM	WKUPM	SUSPM	RESETM	SOFM	ESOFM				RESUME	FSUSP	LPMODE	PDWN	FRES
0x44	ISTR	CTR	PMAOVR	ERR	WKUP	SUSP	RESET	SOF	ESOF				DIR	EP_ID
0x48	FNR	RXDP	RXDM	LCK	LSOF		FN
0x4c	DADDR									EF	ADD
0x50	BTABLE	BTABLE

Toggle registers

EP0R

endpoint 0 register

Offset: 0x0, size: 32, reset: 0x00000000, access: Unspecified

5/10 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CTR_RX rw	DTOG_RX rw	STAT_RX rw		SETUP r	EP_TYPE rw		EP_KIND rw	CTR_TX rw	DTOG_TX rw	STAT_TX rw		EA rw

Toggle fields

EA

Bits 0-3: Endpoint address.

Allowed values: 0x0-0xf

STAT_TX

Bits 4-5: Status bits, for transmission transfers.

Allowed values:
0: Disabled: all transmission requests addressed to this endpoint are ignored
1: Stall: the endpoint is stalled and all transmission requests result in a STALL handshake
2: Nak: the endpoint is naked and all transmission requests result in a NAK handshake
3: Valid: this endpoint is enabled for transmission

DTOG_TX

Bit 6: Data Toggle, for transmission transfers.

CTR_TX

Bit 7: Correct Transfer for transmission.

EP_KIND

Bit 8: Endpoint kind.

EP_TYPE

Bits 9-10: Endpoint type.

Allowed values:
0: Bulk: Bulk endpoint
1: Control: Control endpoint
2: Iso: Iso endpoint
3: Interrupt: Interrupt endpoint

SETUP

Bit 11: Setup transaction completed.

STAT_RX

Bits 12-13: Status bits, for reception transfers.

Allowed values:
0: Disabled: all reception requests addressed to this endpoint are ignored
1: Stall: the endpoint is stalled and all reception requests result in a STALL handshake
2: Nak: the endpoint is naked and all reception requests result in a NAK handshake
3: Valid: this endpoint is enabled for reception

DTOG_RX

Bit 14: Data Toggle, for reception transfers.

CTR_RX

Bit 15: Correct transfer for reception.

EP1R

endpoint 1 register

Offset: 0x4, size: 32, reset: 0x00000000, access: Unspecified

5/10 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CTR_RX rw	DTOG_RX rw	STAT_RX rw		SETUP r	EP_TYPE rw		EP_KIND rw	CTR_TX rw	DTOG_TX rw	STAT_TX rw		EA rw

Toggle fields

EA

Bits 0-3: Endpoint address.

Allowed values: 0x0-0xf

STAT_TX

Bits 4-5: Status bits, for transmission transfers.

Allowed values:
0: Disabled: all transmission requests addressed to this endpoint are ignored
1: Stall: the endpoint is stalled and all transmission requests result in a STALL handshake
2: Nak: the endpoint is naked and all transmission requests result in a NAK handshake
3: Valid: this endpoint is enabled for transmission

DTOG_TX

Bit 6: Data Toggle, for transmission transfers.

CTR_TX

Bit 7: Correct Transfer for transmission.

EP_KIND

Bit 8: Endpoint kind.

EP_TYPE

Bits 9-10: Endpoint type.

Allowed values:
0: Bulk: Bulk endpoint
1: Control: Control endpoint
2: Iso: Iso endpoint
3: Interrupt: Interrupt endpoint

SETUP

Bit 11: Setup transaction completed.

STAT_RX

Bits 12-13: Status bits, for reception transfers.

Allowed values:
0: Disabled: all reception requests addressed to this endpoint are ignored
1: Stall: the endpoint is stalled and all reception requests result in a STALL handshake
2: Nak: the endpoint is naked and all reception requests result in a NAK handshake
3: Valid: this endpoint is enabled for reception

DTOG_RX

Bit 14: Data Toggle, for reception transfers.

CTR_RX

Bit 15: Correct transfer for reception.

EP2R

endpoint 2 register

Offset: 0x8, size: 32, reset: 0x00000000, access: Unspecified

5/10 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CTR_RX rw	DTOG_RX rw	STAT_RX rw		SETUP r	EP_TYPE rw		EP_KIND rw	CTR_TX rw	DTOG_TX rw	STAT_TX rw		EA rw

Toggle fields

EA

Bits 0-3: Endpoint address.

Allowed values: 0x0-0xf

STAT_TX

Bits 4-5: Status bits, for transmission transfers.

Allowed values:
0: Disabled: all transmission requests addressed to this endpoint are ignored
1: Stall: the endpoint is stalled and all transmission requests result in a STALL handshake
2: Nak: the endpoint is naked and all transmission requests result in a NAK handshake
3: Valid: this endpoint is enabled for transmission

DTOG_TX

Bit 6: Data Toggle, for transmission transfers.

CTR_TX

Bit 7: Correct Transfer for transmission.

EP_KIND

Bit 8: Endpoint kind.

EP_TYPE

Bits 9-10: Endpoint type.

Allowed values:
0: Bulk: Bulk endpoint
1: Control: Control endpoint
2: Iso: Iso endpoint
3: Interrupt: Interrupt endpoint

SETUP

Bit 11: Setup transaction completed.

STAT_RX

Bits 12-13: Status bits, for reception transfers.

Allowed values:
0: Disabled: all reception requests addressed to this endpoint are ignored
1: Stall: the endpoint is stalled and all reception requests result in a STALL handshake
2: Nak: the endpoint is naked and all reception requests result in a NAK handshake
3: Valid: this endpoint is enabled for reception

DTOG_RX

Bit 14: Data Toggle, for reception transfers.

CTR_RX

Bit 15: Correct transfer for reception.

EP3R

endpoint 3 register

Offset: 0xc, size: 32, reset: 0x00000000, access: Unspecified

5/10 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CTR_RX rw	DTOG_RX rw	STAT_RX rw		SETUP r	EP_TYPE rw		EP_KIND rw	CTR_TX rw	DTOG_TX rw	STAT_TX rw		EA rw

Toggle fields

EA

Bits 0-3: Endpoint address.

Allowed values: 0x0-0xf

STAT_TX

Bits 4-5: Status bits, for transmission transfers.

Allowed values:
0: Disabled: all transmission requests addressed to this endpoint are ignored
1: Stall: the endpoint is stalled and all transmission requests result in a STALL handshake
2: Nak: the endpoint is naked and all transmission requests result in a NAK handshake
3: Valid: this endpoint is enabled for transmission

DTOG_TX

Bit 6: Data Toggle, for transmission transfers.

CTR_TX

Bit 7: Correct Transfer for transmission.

EP_KIND

Bit 8: Endpoint kind.

EP_TYPE

Bits 9-10: Endpoint type.

Allowed values:
0: Bulk: Bulk endpoint
1: Control: Control endpoint
2: Iso: Iso endpoint
3: Interrupt: Interrupt endpoint

SETUP

Bit 11: Setup transaction completed.

STAT_RX

Bits 12-13: Status bits, for reception transfers.

Allowed values:
0: Disabled: all reception requests addressed to this endpoint are ignored
1: Stall: the endpoint is stalled and all reception requests result in a STALL handshake
2: Nak: the endpoint is naked and all reception requests result in a NAK handshake
3: Valid: this endpoint is enabled for reception

DTOG_RX

Bit 14: Data Toggle, for reception transfers.

CTR_RX

Bit 15: Correct transfer for reception.

EP4R

endpoint 4 register

Offset: 0x10, size: 32, reset: 0x00000000, access: Unspecified

5/10 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CTR_RX rw	DTOG_RX rw	STAT_RX rw		SETUP r	EP_TYPE rw		EP_KIND rw	CTR_TX rw	DTOG_TX rw	STAT_TX rw		EA rw

Toggle fields

EA

Bits 0-3: Endpoint address.

Allowed values: 0x0-0xf

STAT_TX

Bits 4-5: Status bits, for transmission transfers.

Allowed values:
0: Disabled: all transmission requests addressed to this endpoint are ignored
1: Stall: the endpoint is stalled and all transmission requests result in a STALL handshake
2: Nak: the endpoint is naked and all transmission requests result in a NAK handshake
3: Valid: this endpoint is enabled for transmission

DTOG_TX

Bit 6: Data Toggle, for transmission transfers.

CTR_TX

Bit 7: Correct Transfer for transmission.

EP_KIND

Bit 8: Endpoint kind.

EP_TYPE

Bits 9-10: Endpoint type.

Allowed values:
0: Bulk: Bulk endpoint
1: Control: Control endpoint
2: Iso: Iso endpoint
3: Interrupt: Interrupt endpoint

SETUP

Bit 11: Setup transaction completed.

STAT_RX

Bits 12-13: Status bits, for reception transfers.

Allowed values:
0: Disabled: all reception requests addressed to this endpoint are ignored
1: Stall: the endpoint is stalled and all reception requests result in a STALL handshake
2: Nak: the endpoint is naked and all reception requests result in a NAK handshake
3: Valid: this endpoint is enabled for reception

DTOG_RX

Bit 14: Data Toggle, for reception transfers.

CTR_RX

Bit 15: Correct transfer for reception.

EP5R

endpoint 5 register

Offset: 0x14, size: 32, reset: 0x00000000, access: Unspecified

5/10 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CTR_RX rw	DTOG_RX rw	STAT_RX rw		SETUP r	EP_TYPE rw		EP_KIND rw	CTR_TX rw	DTOG_TX rw	STAT_TX rw		EA rw

Toggle fields

EA

Bits 0-3: Endpoint address.

Allowed values: 0x0-0xf

STAT_TX

Bits 4-5: Status bits, for transmission transfers.

Allowed values:
0: Disabled: all transmission requests addressed to this endpoint are ignored
1: Stall: the endpoint is stalled and all transmission requests result in a STALL handshake
2: Nak: the endpoint is naked and all transmission requests result in a NAK handshake
3: Valid: this endpoint is enabled for transmission

DTOG_TX

Bit 6: Data Toggle, for transmission transfers.

CTR_TX

Bit 7: Correct Transfer for transmission.

EP_KIND

Bit 8: Endpoint kind.

EP_TYPE

Bits 9-10: Endpoint type.

Allowed values:
0: Bulk: Bulk endpoint
1: Control: Control endpoint
2: Iso: Iso endpoint
3: Interrupt: Interrupt endpoint

SETUP

Bit 11: Setup transaction completed.

STAT_RX

Bits 12-13: Status bits, for reception transfers.

Allowed values:
0: Disabled: all reception requests addressed to this endpoint are ignored
1: Stall: the endpoint is stalled and all reception requests result in a STALL handshake
2: Nak: the endpoint is naked and all reception requests result in a NAK handshake
3: Valid: this endpoint is enabled for reception

DTOG_RX

Bit 14: Data Toggle, for reception transfers.

CTR_RX

Bit 15: Correct transfer for reception.

EP6R

endpoint 6 register

Offset: 0x18, size: 32, reset: 0x00000000, access: Unspecified

5/10 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CTR_RX rw	DTOG_RX rw	STAT_RX rw		SETUP r	EP_TYPE rw		EP_KIND rw	CTR_TX rw	DTOG_TX rw	STAT_TX rw		EA rw

Toggle fields

EA

Bits 0-3: Endpoint address.

Allowed values: 0x0-0xf

STAT_TX

Bits 4-5: Status bits, for transmission transfers.

Allowed values:
0: Disabled: all transmission requests addressed to this endpoint are ignored
1: Stall: the endpoint is stalled and all transmission requests result in a STALL handshake
2: Nak: the endpoint is naked and all transmission requests result in a NAK handshake
3: Valid: this endpoint is enabled for transmission

DTOG_TX

Bit 6: Data Toggle, for transmission transfers.

CTR_TX

Bit 7: Correct Transfer for transmission.

EP_KIND

Bit 8: Endpoint kind.

EP_TYPE

Bits 9-10: Endpoint type.

Allowed values:
0: Bulk: Bulk endpoint
1: Control: Control endpoint
2: Iso: Iso endpoint
3: Interrupt: Interrupt endpoint

SETUP

Bit 11: Setup transaction completed.

STAT_RX

Bits 12-13: Status bits, for reception transfers.

Allowed values:
0: Disabled: all reception requests addressed to this endpoint are ignored
1: Stall: the endpoint is stalled and all reception requests result in a STALL handshake
2: Nak: the endpoint is naked and all reception requests result in a NAK handshake
3: Valid: this endpoint is enabled for reception

DTOG_RX

Bit 14: Data Toggle, for reception transfers.

CTR_RX

Bit 15: Correct transfer for reception.

EP7R

endpoint 7 register

Offset: 0x1c, size: 32, reset: 0x00000000, access: Unspecified

5/10 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CTR_RX rw	DTOG_RX rw	STAT_RX rw		SETUP r	EP_TYPE rw		EP_KIND rw	CTR_TX rw	DTOG_TX rw	STAT_TX rw		EA rw

Toggle fields

EA

Bits 0-3: Endpoint address.

Allowed values: 0x0-0xf

STAT_TX

Bits 4-5: Status bits, for transmission transfers.

Allowed values:
0: Disabled: all transmission requests addressed to this endpoint are ignored
1: Stall: the endpoint is stalled and all transmission requests result in a STALL handshake
2: Nak: the endpoint is naked and all transmission requests result in a NAK handshake
3: Valid: this endpoint is enabled for transmission

DTOG_TX

Bit 6: Data Toggle, for transmission transfers.

CTR_TX

Bit 7: Correct Transfer for transmission.

EP_KIND

Bit 8: Endpoint kind.

EP_TYPE

Bits 9-10: Endpoint type.

Allowed values:
0: Bulk: Bulk endpoint
1: Control: Control endpoint
2: Iso: Iso endpoint
3: Interrupt: Interrupt endpoint

SETUP

Bit 11: Setup transaction completed.

STAT_RX

Bits 12-13: Status bits, for reception transfers.

Allowed values:
0: Disabled: all reception requests addressed to this endpoint are ignored
1: Stall: the endpoint is stalled and all reception requests result in a STALL handshake
2: Nak: the endpoint is naked and all reception requests result in a NAK handshake
3: Valid: this endpoint is enabled for reception

DTOG_RX

Bit 14: Data Toggle, for reception transfers.

CTR_RX

Bit 15: Correct transfer for reception.

CNTR

control register

Offset: 0x40, size: 32, reset: 0x00000003, access: read-write

13/13 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CTRM rw	PMAOVRM rw	ERRM rw	WKUPM rw	SUSPM rw	RESETM rw	SOFM rw	ESOFM rw				RESUME rw	FSUSP rw	LPMODE rw	PDWN rw	FRES rw

Toggle fields

FRES

Bit 0: Force USB Reset.

Allowed values:
0: NoReset: Clear USB reset
1: Reset: Force a reset of the USB peripheral, exactly like a RESET signaling on the USB

PDWN

Bit 1: Power down.

Allowed values:
0: Disabled: No power down
1: Enabled: Enter power down mode

LPMODE

Bit 2: Low-power mode.

Allowed values:
0: Disabled: No low-power mode
1: Enabled: Enter low-power mode

FSUSP

Bit 3: Force suspend.

Allowed values:
0: NoEffect: No effect
1: Suspend: Enter suspend mode. Clocks and static power dissipation in the analog transceiver are left unaffected

RESUME

Bit 4: Resume request.

Allowed values:
1: Requested: Resume requested

ESOFM

Bit 8: Expected start of frame interrupt mask.

Allowed values:
0: Disabled: ESOF Interrupt disabled
1: Enabled: ESOF Interrupt enabled, an interrupt request is generated when the corresponding bit in the USB_ISTR register is set

SOFM

Bit 9: Start of frame interrupt mask.

Allowed values:
0: Disabled: SOF Interrupt disabled
1: Enabled: SOF Interrupt enabled, an interrupt request is generated when the corresponding bit in the USB_ISTR register is set

RESETM

Bit 10: USB reset interrupt mask.

Allowed values:
0: Disabled: RESET Interrupt disabled
1: Enabled: RESET Interrupt enabled, an interrupt request is generated when the corresponding bit in the USB_ISTR register is set

SUSPM

Bit 11: Suspend mode interrupt mask.

Allowed values:
0: Disabled: Suspend Mode Request SUSP Interrupt disabled
1: Enabled: SUSP Interrupt enabled, an interrupt request is generated when the corresponding bit in the USB_ISTR register is set

WKUPM

Bit 12: Wakeup interrupt mask.

Allowed values:
0: Disabled: WKUP Interrupt disabled
1: Enabled: WKUP Interrupt enabled, an interrupt request is generated when the corresponding bit in the USB_ISTR register is set

ERRM

Bit 13: Error interrupt mask.

Allowed values:
0: Disabled: ERR Interrupt disabled
1: Enabled: ERR Interrupt enabled, an interrupt request is generated when the corresponding bit in the USB_ISTR register is set

PMAOVRM

Bit 14: Packet memory area over / underrun interrupt mask.

Allowed values:
0: Disabled: PMAOVR Interrupt disabled
1: Enabled: PMAOVR Interrupt enabled, an interrupt request is generated when the corresponding bit in the USB_ISTR register is set

CTRM

Bit 15: Correct transfer interrupt mask.

Allowed values:
0: Disabled: Correct Transfer (CTR) Interrupt disabled
1: Enabled: CTR Interrupt enabled, an interrupt request is generated when the corresponding bit in the USB_ISTR register is set

ISTR

interrupt status register

Offset: 0x44, size: 32, reset: 0x00000000, access: Unspecified

10/10 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CTR r	PMAOVR rw	ERR rw	WKUP rw	SUSP rw	RESET rw	SOF rw	ESOF rw				DIR r	EP_ID r

Toggle fields

EP_ID

Bits 0-3: Endpoint Identifier.

Allowed values: 0x0-0xf

DIR

Bit 4: Direction of transaction.

Allowed values:
0: To: data transmitted by the USB peripheral to the host PC
1: From: data received by the USB peripheral from the host PC

ESOF

Bit 8: Expected start frame.

Allowed values:
0: NotExpectedStartOfFrame: NotExpectedStartOfFrame
1: ExpectedStartOfFrame: an SOF packet is expected but not received

SOF

Bit 9: start of frame.

Allowed values:
0: NotStartOfFrame: NotStartOfFrame
1: StartOfFrame: beginning of a new USB frame and it is set when a SOF packet arrives through the USB bus

RESET

Bit 10: reset request.

Allowed values:
0: NotReset: NotReset
1: Reset: peripheral detects an active USB RESET signal at its inputs

SUSP

Bit 11: Suspend mode request.

Allowed values:
0: NotSuspend: NotSuspend
1: Suspend: no traffic has been received for 3 ms, indicating a suspend mode request from the USB bus

WKUP

Bit 12: Wakeup.

Allowed values:
0: NotWakeup: NotWakeup
1: Wakeup: activity is detected that wakes up the USB peripheral

ERR

Bit 13: Error.

Allowed values:
0: NotOverrun: Errors are not occurred
1: Error: One of No ANSwer, Cyclic Redundancy Check, Bit Stuffing or Framing format Violation error occurred

PMAOVR

Bit 14: Packet memory area over / underrun.

Allowed values:
0: NotOverrun: Overrun is not occurred
1: Overrun: microcontroller has not been able to respond in time to an USB memory request

CTR

Bit 15: Correct transfer.

Allowed values:
1: Completed: endpoint has successfully completed a transaction

FNR

frame number register

Offset: 0x48, size: 32, reset: 0x00000000, access: read-only

5/5 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RXDP r	RXDM r	LCK r	LSOF r		FN r

Toggle fields

FN

Bits 0-10: Frame number.

Allowed values: 0x0-0x7ff

LSOF

Bits 11-12: Lost SOF.

Allowed values: 0x0-0x3

LCK

Bit 13: Locked.

Allowed values:
1: Locked: the frame timer remains in this state until an USB reset or USB suspend event occurs

RXDM

Bit 14: Receive data - line status.

Allowed values:
1: Received: received data minus upstream port data line

RXDP

Bit 15: Receive data + line status.

Allowed values:
1: Received: received data plus upstream port data line

DADDR

device address

Offset: 0x4c, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								EF rw	ADD rw

Toggle fields

ADD

Bits 0-6: Device address.

Allowed values: 0x0-0x7f

EF

Bit 7: Enable function.

Allowed values:
0: Disabled: USB device disabled
1: Enabled: USB device enabled

BTABLE

Buffer table address

Offset: 0x50, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BTABLE rw

Toggle fields

BTABLE

Bits 3-15: Buffer table.

Allowed values: 0x0-0x1fff

WWDG

0x40002c00: Window watchdog

6/6 fields covered.

Toggle register map

Offset	Name	9	8	7	6	0
0x0	CR			WDGA	T
0x4	CFR	EWI	WDGTB		W
0x8	SR					EWIF

Toggle registers

CR

Control register

Offset: 0x0, size: 32, reset: 0x0000007F, access: read-write

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								WDGA rw	T rw

Toggle fields

T

Bits 0-6: 7-bit counter.

Allowed values: 0x0-0x7f

WDGA

Bit 7: Activation bit.

Allowed values:
0: Disabled: Watchdog disabled
1: Enabled: Watchdog enabled

CFR

Configuration register

Offset: 0x4, size: 32, reset: 0x0000007F, access: read-write

3/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						EWI rw	WDGTB rw		W rw

Toggle fields

W

Bits 0-6: 7-bit window value.

Allowed values: 0x0-0x7f

WDGTB

Bits 7-8: Timer base.

Allowed values:
0: Div1: Counter clock (PCLK1 div 4096) div 1
1: Div2: Counter clock (PCLK1 div 4096) div 2
2: Div4: Counter clock (PCLK1 div 4096) div 4
3: Div8: Counter clock (PCLK1 div 4096) div 8

EWI

Bit 9: Early wakeup interrupt.

Allowed values:
1: Enable: interrupt occurs whenever the counter reaches the value 0x40

SR

Status register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
															EWIF rw

Toggle fields

EWIF

Bit 0: Early wakeup interrupt flag.

Allowed values:
0: Finished: The EWI Interrupt Service Routine has been serviced
1: Pending: The EWI Interrupt Service Routine has been triggered