STM32G041 Peripheral Coverage

ADC

0x40012400: Analog to Digital Converter instance 1

74/74 fields covered.

Toggle register map

Offset	Name	31	30	29	28	27	26	24	23	22	21	19	18	16	15	14	13	12	11	9	8	7	6	5	4	3	2	1	0
0x0	ISR																CCRDY		EOCAL	AWD3	AWD2	AWD1			OVR	EOS	EOC	EOSMP	ADRDY
0x4	IER																CCRDYIE		EOCALIE	AWD3IE	AWD2IE	AWD1IE			OVRIE	EOSIE	EOCIE	EOSMPIE	ADRDYIE
0x8	CR	ADCAL			ADVREGEN																				ADSTP		ADSTART	ADDIS	ADEN
0xc	CFGR1		AWD1CH						AWD1EN	AWD1SGL	CHSELRMOD			DISCEN	AUTOFF	WAIT	CONT	OVRMOD	EXTEN		EXTSEL			ALIGN	RES		SCANDIR	DMACFG	DMAEN
0x10	CFGR2	CKMODE		LFTRIG																TOVS	OVSS				OVSR				OVSE
0x14	SMPR						SMPSEL								SMPSEL								SMP2				SMP1
0x20	AWD1TR					HT1													LT1
0x24	AWD2TR					HT2													LT2
0x28	CHSELR0												CHSEL		CHSEL
0x28	CHSELR1	SQ8				SQ7			SQ6			SQ5			SQ4				SQ3			SQ2				SQ1
0x2c	AWD3TR					HT3													LT3
0x40	DR														DATA
0xa0	AWD2CR												AWD2CH		AWD2CH
0xa4	AWD3CR												AWD3CH		AWD3CH
0xb4	CALFACT																						CALFACT
0x308	CCR							VBATEN	TSEN	VREFEN	PRESC

Toggle registers

ISR

ADC interrupt and status register

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

10/10 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		CCRDY rw		EOCAL rw		AWD3 rw	AWD2 rw	AWD1 rw			OVR rw	EOS rw	EOC rw	EOSMP rw	ADRDY rw

Toggle fields

ADRDY

Bit 0: ADC ready flag.

Allowed values:
0: NotReady: ADC not yet ready to start conversion
1: Ready: ADC ready to start conversion

EOSMP

Bit 1: ADC group regular end of sampling flag.

Allowed values:
0: NotAtEnd: Not at the end of the samplings phase
1: AtEnd: End of sampling phase reached

EOC

Bit 2: ADC group regular end of unitary conversion flag.

Allowed values:
0: NotComplete: Channel conversion is not complete
1: Complete: Channel conversion complete

EOS

Bit 3: ADC group regular end of sequence conversions flag.

Allowed values:
0: NotComplete: Conversion sequence is not complete
1: Complete: Conversion sequence complete

OVR

Bit 4: ADC group regular overrun flag.

Allowed values:
0: NoOverrun: No overrun occurred
1: Overrun: Overrun occurred

AWD1

Bit 7: ADC analog watchdog 1 flag.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

AWD2

Bit 8: ADC analog watchdog 2 flag.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

AWD3

Bit 9: ADC analog watchdog 3 flag.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

EOCAL

Bit 11: End Of Calibration flag.

Allowed values:
0: NotComplete: Calibration is not complete
1: Complete: Calibration complete

CCRDY

Bit 13: Channel Configuration Ready flag.

Allowed values:
0: NotComplete: Channel configuration update not applied
1: Complete: Channel configuration update is applied

IER

ADC interrupt enable register

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

10/10 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		CCRDYIE rw		EOCALIE rw		AWD3IE rw	AWD2IE rw	AWD1IE rw			OVRIE rw	EOSIE rw	EOCIE rw	EOSMPIE rw	ADRDYIE rw

Toggle fields

ADRDYIE

Bit 0: ADC ready interrupt.

Allowed values:
0: Disabled: ADRDY interrupt disabled
1: Enabled: ADRDY interrupt enabled. An interrupt is generated when the ADRDY bit is set.

EOSMPIE

Bit 1: ADC group regular end of sampling interrupt.

Allowed values:
0: Disabled: EOSMP interrupt disabled
1: Enabled: EOSMP interrupt enabled. An interrupt is generated when the EOSMP bit is set.

EOCIE

Bit 2: ADC group regular end of unitary conversion interrupt.

Allowed values:
0: Disabled: EOC interrupt disabled
1: Enabled: EOC interrupt enabled. An interrupt is generated when the EOC bit is set.

EOSIE

Bit 3: ADC group regular end of sequence conversions interrupt.

Allowed values:
0: Disabled: EOS interrupt disabled
1: Enabled: EOS interrupt enabled. An interrupt is generated when the EOS bit is set.

OVRIE

Bit 4: ADC group regular overrun interrupt.

Allowed values:
0: Disabled: Overrun interrupt disabled
1: Enabled: Overrun interrupt enabled. An interrupt is generated when the OVR bit is set.

AWD1IE

Bit 7: ADC analog watchdog 1 interrupt.

Allowed values:
0: Disabled: Analog watchdog interrupt disabled
1: Enabled: Analog watchdog interrupt enabled

AWD2IE

Bit 8: ADC analog watchdog 2 interrupt.

Allowed values:
0: Disabled: Analog watchdog interrupt disabled
1: Enabled: Analog watchdog interrupt enabled

AWD3IE

Bit 9: ADC analog watchdog 3 interrupt.

Allowed values:
0: Disabled: Analog watchdog interrupt disabled
1: Enabled: Analog watchdog interrupt enabled

EOCALIE

Bit 11: End of calibration interrupt enable.

Allowed values:
0: Disabled: End of calibration interrupt disabled
1: Enabled: End of calibration interrupt enabled

CCRDYIE

Bit 13: Channel Configuration Ready Interrupt enable.

Allowed values:
0: Disabled: Channel configuration ready interrupt disabled
1: Enabled: Channel configuration ready interrupt enabled

CR

ADC control register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

6/6 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ADCAL rw			ADVREGEN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
											ADSTP rw		ADSTART rw	ADDIS rw	ADEN rw

Toggle fields

ADEN

Bit 0: ADC enable.

Allowed values:
0: Disabled: ADC disabled
1: Enabled: ADC enabled

ADDIS

Bit 1: ADC disable.

Allowed values:
0: NotDisabling: No disable command active
1: Disabling: ADC disabling

ADSTART

Bit 2: ADC group regular conversion start.

Allowed values:
0: NotActive: No conversion ongoing
1: Active: ADC operating and may be converting

ADSTP

Bit 4: ADC group regular conversion stop.

Allowed values:
0: NotStopping: No stop command active
1: Stopping: ADC stopping conversion

ADVREGEN

Bit 28: ADC voltage regulator enable.

Allowed values:
0: Disabled: ADC voltage regulator disabled
1: Enabled: ADC voltage regulator enabled

ADCAL

Bit 31: ADC calibration.

Allowed values:
0: NotCalibrating: ADC calibration either not yet performed or completed
1: Calibrating: ADC calibration in progress

CFGR1

ADC configuration register 1

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
	AWD1CH rw							AWD1EN rw	AWD1SGL rw	CHSELRMOD rw					DISCEN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AUTOFF rw	WAIT rw	CONT rw	OVRMOD rw	EXTEN rw			EXTSEL rw			ALIGN rw	RES rw		SCANDIR rw	DMACFG rw	DMAEN rw

Toggle fields

DMAEN

Bit 0: ADC DMA transfer enable.

Allowed values:
0: Disabled: DMA disabled
1: Enabled: DMA enabled

DMACFG

Bit 1: ADC DMA transfer configuration.

Allowed values:
0: OneShot: DMA one shot mode selected
1: Circular: DMA circular mode selected

SCANDIR

Bit 2: Scan sequence direction.

Allowed values:
0: Upward: Upward scan (from CHSEL0 to CHSEL17)
1: Backward: Backward scan (from CHSEL17 to CHSEL0)

RES

Bits 3-4: ADC data resolution.

Allowed values:
0: Bits12: 12 bits
1: Bits10: 10 bits
2: Bits8: 8 bits
3: Bits6: 6 bits

ALIGN

Bit 5: ADC data alignement.

Allowed values:
0: Right: Right alignment
1: Left: Left alignment

EXTSEL

Bits 6-8: ADC group regular external trigger source.

Allowed values:
0: TIM1_TRGO: Timer 1 TRGO event
1: TIM1_CC4: Timer 1 CC4 event
2: TIM2_TRGO: Timer 2 TRGO event
3: TIM2_CH4: Timer 2 CH4 event
5: TIM2_CH3: Timer 2 CH3 event
7: EXTI_LINE11: EXTI line 11 event

EXTEN

Bits 10-11: ADC group regular external trigger polarity.

Allowed values:
0: Disabled: Hardware trigger detection disabled
1: RisingEdge: Hardware trigger detection on the rising edge
2: FallingEdge: Hardware trigger detection on the falling edge
3: BothEdges: Hardware trigger detection on both the rising and falling edges

OVRMOD

Bit 12: ADC group regular overrun configuration.

Allowed values:
0: Preserve: ADC_DR register is preserved with the old data when an overrun is detected
1: Overwrite: ADC_DR register is overwritten with the last conversion result when an overrun is detected

CONT

Bit 13: ADC group regular continuous conversion mode.

Allowed values:
0: Single: Single conversion mode
1: Continuous: Continuous conversion mode

WAIT

Bit 14: Wait conversion mode.

Allowed values:
0: Disabled: Wait conversion mode off
1: Enabled: Wait conversion mode on

AUTOFF

Bit 15: Auto-off mode.

Allowed values:
0: Disabled: Auto-off mode disabled
1: Enabled: Auto-off mode enabled

DISCEN

Bit 16: ADC group regular sequencer discontinuous mode.

Allowed values:
0: Disabled: Discontinuous mode disabled
1: Enabled: Discontinuous mode enabled

CHSELRMOD

Bit 21: Mode selection of the ADC_CHSELR register.

Allowed values:
0: BitPerInput: Each bit of the ADC_CHSELR register enables an input
1: Sequence: ADC_CHSELR register is able to sequence up to 8 channels

AWD1SGL

Bit 22: ADC analog watchdog 1 monitoring a single channel or all channels.

Allowed values:
0: AllChannels: Analog watchdog 1 enabled on all channels
1: SingleChannel: Analog watchdog 1 enabled on a single channel

AWD1EN

Bit 23: ADC analog watchdog 1 enable on scope ADC group regular.

Allowed values:
0: Disabled: Analog watchdog 1 disabled
1: Enabled: Analog watchdog 1 enabled

AWD1CH

Bits 26-30: ADC analog watchdog 1 monitored channel selection.

Allowed values: 0x0-0x11

CFGR2

ADC configuration register 2

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

6/6 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
CKMODE rw		LFTRIG rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						TOVS rw	OVSS rw				OVSR rw				OVSE rw

Toggle fields

OVSE

Bit 0: ADC oversampler enable on scope ADC group regular.

Allowed values:
0: Disabled: Oversampler disabled
1: Enabled: Oversampler enabled

OVSR

Bits 2-4: ADC oversampling ratio.

Allowed values:
0: Mul2: 2x
1: Mul4: 4x
2: Mul8: 8x
3: Mul16: 16x
4: Mul32: 32x
5: Mul64: 64x
6: Mul128: 128x
7: Mul256: 256x

OVSS

Bits 5-8: ADC oversampling shift.

Allowed values:
0: NoShift: No shift
1: Shift1: Shift 1-bit
2: Shift2: Shift 2-bits
3: Shift3: Shift 3-bits
4: Shift4: Shift 4-bits
5: Shift5: Shift 5-bits
6: Shift6: Shift 6-bits
7: Shift7: Shift 7-bits
8: Shift8: Shift 8-bits

TOVS

Bit 9: ADC oversampling discontinuous mode (triggered mode) for ADC group regular.

Allowed values:
0: TriggerAll: All oversampled conversions for a channel are done consecutively after a trigger
1: TriggerEach: Each oversampled conversion for a channel needs a trigger

LFTRIG

Bit 29: Low frequency trigger mode enable.

Allowed values:
0: Disabled: Low Frequency Trigger Mode disabled
1: Enabled: Low Frequency Trigger Mode enabled

CKMODE

Bits 30-31: ADC clock mode.

Allowed values:
0: ADCLK: ADCCLK (Asynchronous clock mode)
1: PCLK_Div2: PCLK/2 (Synchronous clock mode)
2: PCLK_Div4: PCLK/4 (Synchronous clock mode)
3: PCLK: PCLK (Synchronous clock mode)

SMPR

ADC sampling time register

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

3/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
					SMPSEL rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SMPSEL rw									SMP2 rw				SMP1 rw

Toggle fields

SMP1

Bits 0-2: Sampling time selection.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles3_5: 3.5 ADC clock cycles
2: Cycles7_5: 7.5 ADC clock cycles
3: Cycles12_5: 12.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles39_5: 39.5 ADC clock cycles
6: Cycles79_5: 79.5 ADC clock cycles
7: Cycles160_5: 160.5 ADC clock cycles

SMP2

Bits 4-6: Sampling time selection.

Allowed values:
0: Cycles1_5: 1.5 ADC clock cycles
1: Cycles3_5: 3.5 ADC clock cycles
2: Cycles7_5: 7.5 ADC clock cycles
3: Cycles12_5: 12.5 ADC clock cycles
4: Cycles19_5: 19.5 ADC clock cycles
5: Cycles39_5: 39.5 ADC clock cycles
6: Cycles79_5: 79.5 ADC clock cycles
7: Cycles160_5: 160.5 ADC clock cycles

SMPSEL

Bits 8-26: Channel sampling time selection.

Allowed values:
0: Smp1: Sampling time of CHANNELx use the setting of SMP1 register
1: Smp2: Sampling time of CHANNELx use the setting of SMP2 register

AWD1TR

watchdog threshold register

Offset: 0x20, size: 32, reset: 0x0FFF0000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				HT1 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				LT1 rw

Toggle fields

LT1

Bits 0-11: ADC analog watchdog 1 threshold low.

Allowed values: 0x0-0xfff

HT1

Bits 16-27: ADC analog watchdog 1 threshold high.

Allowed values: 0x0-0xfff

AWD2TR

watchdog threshold register

Offset: 0x24, size: 32, reset: 0x0FFF0000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				HT2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				LT2 rw

Toggle fields

LT2

Bits 0-11: ADC analog watchdog 2 threshold low.

Allowed values: 0x0-0xfff

HT2

Bits 16-27: ADC analog watchdog 2 threshold high.

Allowed values: 0x0-0xfff

CHSELR0

channel selection register

Offset: 0x28, size: 32, reset: 0x0FFF0000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
													CHSEL rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CHSEL rw

Toggle fields

CHSEL

Bits 0-18: Channel-x selection.

Allowed values:
0: NotSelected: Input Channel is not selected for conversion
1: Selected: Input Channel is selected for conversion

CHSELR1

channel selection register CHSELRMOD = 1 in ADC_CFGR1

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
SQ8 rw				SQ7 rw				SQ6 rw				SQ5 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SQ4 rw				SQ3 rw				SQ2 rw				SQ1 rw

Toggle fields

SQ1

Bits 0-3: conversion of the sequence.

Allowed values:
0: Ch0: Channel 0 selected for the Nth conversion
1: Ch1: Channel 1 selected for the Nth conversion
2: Ch2: Channel 2 selected for the Nth conversion
3: Ch3: Channel 3 selected for the Nth conversion
4: Ch4: Channel 4 selected for the Nth conversion
5: Ch5: Channel 5 selected for the Nth conversion
6: Ch6: Channel 6 selected for the Nth conversion
7: Ch7: Channel 7 selected for the Nth conversion
8: Ch8: Channel 8 selected for the Nth conversion
9: Ch9: Channel 9 selected for the Nth conversion
10: Ch10: Channel 10 selected for the Nth conversion
11: Ch11: Channel 11 selected for the Nth conversion
12: Ch12: Channel 12 selected for the Nth conversion
13: Ch13: Channel 13 selected for the Nth conversion
14: Ch14: Channel 14 selected for the Nth conversion
15: EOS: End of sequence

SQ2

Bits 4-7: conversion of the sequence.

Allowed values:
0: Ch0: Channel 0 selected for the Nth conversion
1: Ch1: Channel 1 selected for the Nth conversion
2: Ch2: Channel 2 selected for the Nth conversion
3: Ch3: Channel 3 selected for the Nth conversion
4: Ch4: Channel 4 selected for the Nth conversion
5: Ch5: Channel 5 selected for the Nth conversion
6: Ch6: Channel 6 selected for the Nth conversion
7: Ch7: Channel 7 selected for the Nth conversion
8: Ch8: Channel 8 selected for the Nth conversion
9: Ch9: Channel 9 selected for the Nth conversion
10: Ch10: Channel 10 selected for the Nth conversion
11: Ch11: Channel 11 selected for the Nth conversion
12: Ch12: Channel 12 selected for the Nth conversion
13: Ch13: Channel 13 selected for the Nth conversion
14: Ch14: Channel 14 selected for the Nth conversion
15: EOS: End of sequence

SQ3

Bits 8-11: conversion of the sequence.

Allowed values:
0: Ch0: Channel 0 selected for the Nth conversion
1: Ch1: Channel 1 selected for the Nth conversion
2: Ch2: Channel 2 selected for the Nth conversion
3: Ch3: Channel 3 selected for the Nth conversion
4: Ch4: Channel 4 selected for the Nth conversion
5: Ch5: Channel 5 selected for the Nth conversion
6: Ch6: Channel 6 selected for the Nth conversion
7: Ch7: Channel 7 selected for the Nth conversion
8: Ch8: Channel 8 selected for the Nth conversion
9: Ch9: Channel 9 selected for the Nth conversion
10: Ch10: Channel 10 selected for the Nth conversion
11: Ch11: Channel 11 selected for the Nth conversion
12: Ch12: Channel 12 selected for the Nth conversion
13: Ch13: Channel 13 selected for the Nth conversion
14: Ch14: Channel 14 selected for the Nth conversion
15: EOS: End of sequence

SQ4

Bits 12-15: conversion of the sequence.

Allowed values:
0: Ch0: Channel 0 selected for the Nth conversion
1: Ch1: Channel 1 selected for the Nth conversion
2: Ch2: Channel 2 selected for the Nth conversion
3: Ch3: Channel 3 selected for the Nth conversion
4: Ch4: Channel 4 selected for the Nth conversion
5: Ch5: Channel 5 selected for the Nth conversion
6: Ch6: Channel 6 selected for the Nth conversion
7: Ch7: Channel 7 selected for the Nth conversion
8: Ch8: Channel 8 selected for the Nth conversion
9: Ch9: Channel 9 selected for the Nth conversion
10: Ch10: Channel 10 selected for the Nth conversion
11: Ch11: Channel 11 selected for the Nth conversion
12: Ch12: Channel 12 selected for the Nth conversion
13: Ch13: Channel 13 selected for the Nth conversion
14: Ch14: Channel 14 selected for the Nth conversion
15: EOS: End of sequence

SQ5

Bits 16-19: conversion of the sequence.

Allowed values:
0: Ch0: Channel 0 selected for the Nth conversion
1: Ch1: Channel 1 selected for the Nth conversion
2: Ch2: Channel 2 selected for the Nth conversion
3: Ch3: Channel 3 selected for the Nth conversion
4: Ch4: Channel 4 selected for the Nth conversion
5: Ch5: Channel 5 selected for the Nth conversion
6: Ch6: Channel 6 selected for the Nth conversion
7: Ch7: Channel 7 selected for the Nth conversion
8: Ch8: Channel 8 selected for the Nth conversion
9: Ch9: Channel 9 selected for the Nth conversion
10: Ch10: Channel 10 selected for the Nth conversion
11: Ch11: Channel 11 selected for the Nth conversion
12: Ch12: Channel 12 selected for the Nth conversion
13: Ch13: Channel 13 selected for the Nth conversion
14: Ch14: Channel 14 selected for the Nth conversion
15: EOS: End of sequence

SQ6

Bits 20-23: conversion of the sequence.

Allowed values:
0: Ch0: Channel 0 selected for the Nth conversion
1: Ch1: Channel 1 selected for the Nth conversion
2: Ch2: Channel 2 selected for the Nth conversion
3: Ch3: Channel 3 selected for the Nth conversion
4: Ch4: Channel 4 selected for the Nth conversion
5: Ch5: Channel 5 selected for the Nth conversion
6: Ch6: Channel 6 selected for the Nth conversion
7: Ch7: Channel 7 selected for the Nth conversion
8: Ch8: Channel 8 selected for the Nth conversion
9: Ch9: Channel 9 selected for the Nth conversion
10: Ch10: Channel 10 selected for the Nth conversion
11: Ch11: Channel 11 selected for the Nth conversion
12: Ch12: Channel 12 selected for the Nth conversion
13: Ch13: Channel 13 selected for the Nth conversion
14: Ch14: Channel 14 selected for the Nth conversion
15: EOS: End of sequence

SQ7

Bits 24-27: conversion of the sequence.

Allowed values:
0: Ch0: Channel 0 selected for the Nth conversion
1: Ch1: Channel 1 selected for the Nth conversion
2: Ch2: Channel 2 selected for the Nth conversion
3: Ch3: Channel 3 selected for the Nth conversion
4: Ch4: Channel 4 selected for the Nth conversion
5: Ch5: Channel 5 selected for the Nth conversion
6: Ch6: Channel 6 selected for the Nth conversion
7: Ch7: Channel 7 selected for the Nth conversion
8: Ch8: Channel 8 selected for the Nth conversion
9: Ch9: Channel 9 selected for the Nth conversion
10: Ch10: Channel 10 selected for the Nth conversion
11: Ch11: Channel 11 selected for the Nth conversion
12: Ch12: Channel 12 selected for the Nth conversion
13: Ch13: Channel 13 selected for the Nth conversion
14: Ch14: Channel 14 selected for the Nth conversion
15: EOS: End of sequence

SQ8

Bits 28-31: conversion of the sequence.

Allowed values:
0: Ch0: Channel 0 selected for the Nth conversion
1: Ch1: Channel 1 selected for the Nth conversion
2: Ch2: Channel 2 selected for the Nth conversion
3: Ch3: Channel 3 selected for the Nth conversion
4: Ch4: Channel 4 selected for the Nth conversion
5: Ch5: Channel 5 selected for the Nth conversion
6: Ch6: Channel 6 selected for the Nth conversion
7: Ch7: Channel 7 selected for the Nth conversion
8: Ch8: Channel 8 selected for the Nth conversion
9: Ch9: Channel 9 selected for the Nth conversion
10: Ch10: Channel 10 selected for the Nth conversion
11: Ch11: Channel 11 selected for the Nth conversion
12: Ch12: Channel 12 selected for the Nth conversion
13: Ch13: Channel 13 selected for the Nth conversion
14: Ch14: Channel 14 selected for the Nth conversion
15: EOS: End of sequence

AWD3TR

watchdog threshold register

Offset: 0x2c, size: 32, reset: 0x0FFF0000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				HT3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				LT3 rw

Toggle fields

LT3

Bits 0-11: ADC analog watchdog 3 threshold high.

Allowed values: 0x0-0xfff

HT3

Bits 16-27: ADC analog watchdog 3 threshold high.

Allowed values: 0x0-0xfff

DR

ADC group regular conversion data register

Offset: 0x40, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DATA r

Toggle fields

DATA

Bits 0-15: ADC group regular conversion data.

Allowed values: 0x0-0xffff

AWD2CR

ADC analog watchdog 2 configuration register

Offset: 0xa0, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
													AWD2CH rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AWD2CH rw

Toggle fields

AWD2CH

Bits 0-18: ADC analog watchdog 2 monitored channel selection.

Allowed values:
0: NotMonitored: ADC analog channel-x is not monitored by AWD2
1: Monitored: ADC analog channel-x is monitored by AWD2

AWD3CR

ADC analog watchdog 3 configuration register

Offset: 0xa4, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
													AWD3CH rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AWD3CH rw

Toggle fields

AWD3CH

Bits 0-18: ADC analog watchdog 3 monitored channel selection.

Allowed values:
0: NotMonitored: ADC analog channel-x is not monitored by AWD3
1: Monitored: ADC analog channel-x is monitored by AWD3

CALFACT

ADC calibration factors register

Offset: 0xb4, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
									CALFACT rw

Toggle fields

CALFACT

Bits 0-6: ADC calibration factor in single-ended mode.

Allowed values: 0x0-0x7f

CCR

ADC common control register

Offset: 0x308, size: 32, reset: 0x00000000, access: read-write

4/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
							VBATEN rw	TSEN rw	VREFEN rw	PRESC rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0

Toggle fields

PRESC

Bits 18-21: ADC prescaler.

Allowed values:
0: Div1: Input ADC clock not divided
1: Div2: Input ADC clock divided by 2
2: Div4: Input ADC clock divided by 4
3: Div6: Input ADC clock divided by 6
4: Div8: Input ADC clock divided by 8
5: Div10: Input ADC clock divided by 10
6: Div12: Input ADC clock divided by 12
7: Div16: Input ADC clock divided by 16
8: Div32: Input ADC clock divided by 32
9: Div64: Input ADC clock divided by 64
10: Div128: Input ADC clock divided by 128
11: Div256: Input ADC clock divided by 256

VREFEN

Bit 22: VREFINT enable.

Allowed values:
0: Disabled: VREFINT disabled
1: Enabled: VREFINT enabled

TSEN

Bit 23: Temperature sensor enable.

Allowed values:
0: Disabled: Temperature sensor disabled
1: Enabled: Temperature sensor enabled

VBATEN

Bit 24: VBAT enable.

Allowed values:
0: Disabled: VBAT channel disabled
1: Enabled: VBAT channel enabled

AES

0x40026000: Advanced encryption standard hardware accelerator 1

5/40 fields covered.

Toggle register map

Offset	Name	31	23	18	16	15	14	12	11	10	9	8	7	6	4	3	2	1	0
0x0	CR		NPBLB	KEYSIZE	CHMOD2		GCMPH	DMAOUTEN	DMAINEN	ERRIE	CCFIE	ERRC	CCFC	CHMOD10	MODE		DATATYPE		EN
0x4	SR															BUSY	WRERR	RDERR	CCF
0x8	DINR	AES_DINR				AES_DINR
0xc	DOUTR	AES_DOUTR				AES_DOUTR
0x10	KEYR0	AES_KEYR0				AES_KEYR0
0x14	KEYR1	AES_KEYR1				AES_KEYR1
0x18	KEYR2	AES_KEYR2				AES_KEYR2
0x1c	KEYR3	AES_KEYR3				AES_KEYR3
0x20	IVR0	AES_IVR0				AES_IVR0
0x24	IVR1	AES_IVR1				AES_IVR1
0x28	IVR2	AES_IVR2				AES_IVR2
0x2c	IVR3	AES_IVR3				AES_IVR3
0x30	KEYR4	AES_KEYR4				AES_KEYR4
0x34	KEYR5	AES_KEYR5				AES_KEYR5
0x38	KEYR6	AES_KEYR6				AES_KEYR6
0x3c	KEYR7	AES_KEYR7				AES_KEYR7
0x40	SUSP0R	AES_SUSP0R				AES_SUSP0R
0x44	SUSP1R	AES_SUSP1R				AES_SUSP1R
0x48	SUSP2R	AES_SUSP2R				AES_SUSP2R
0x4c	SUSP3R	AES_SUSP3R				AES_SUSP3R
0x50	SUSP4R	AES_SUSP4R				AES_SUSP4R
0x54	SUSP5R	AES_SUSP5R				AES_SUSP5R
0x58	SUSP6R	AES_SUSP6R				AES_SUSP6R
0x5c	SUSP7R	AES_SUSP7R				AES_SUSP7R

Toggle registers

CR

control register

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

0/14 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								NPBLB rw					KEYSIZE rw		CHMOD2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	GCMPH rw		DMAOUTEN rw	DMAINEN rw	ERRIE rw	CCFIE rw	ERRC rw	CCFC rw	CHMOD10 rw		MODE rw		DATATYPE rw		EN rw

Toggle fields

EN

Bit 0: AES enable.

DATATYPE

Bits 1-2: Data type selection (for data in and data out to/from the cryptographic block).

MODE

Bits 3-4: AES operating mode.

CHMOD10

Bits 5-6: AES chaining mode Bit1 Bit0.

CCFC

Bit 7: Computation Complete Flag Clear.

ERRC

Bit 8: Error clear.

CCFIE

Bit 9: CCF flag interrupt enable.

ERRIE

Bit 10: Error interrupt enable.

DMAINEN

Bit 11: Enable DMA management of data input phase.

DMAOUTEN

Bit 12: Enable DMA management of data output phase.

GCMPH

Bits 13-14: Used only for GCM, CCM and GMAC algorithms and has no effect when other algorithms are selected.

CHMOD2

Bit 16: AES chaining mode Bit2.

KEYSIZE

Bit 18: Key size selection.

NPBLB

Bits 20-23: Number of padding bytes in last block of payload.

SR

status register

Offset: 0x4, size: 32, reset: 0x00000000, access: read-only

4/4 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
												BUSY r	WRERR r	RDERR r	CCF r

Toggle fields

CCF

Bit 0: Computation complete flag.

RDERR

Bit 1: Read error flag.

WRERR

Bit 2: Write error flag.

BUSY

Bit 3: Busy flag.

DINR

data input register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AES_DINR rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AES_DINR rw

Toggle fields

AES_DINR

Bits 0-31: Data Input Register.

DOUTR

data output register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AES_DOUTR r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AES_DOUTR r

Toggle fields

AES_DOUTR

Bits 0-31: Data output register.

KEYR0

key register 0

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AES_KEYR0 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AES_KEYR0 rw

Toggle fields

AES_KEYR0

Bits 0-31: Data Output Register (LSB key [31:0]).

KEYR1

key register 1

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AES_KEYR1 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AES_KEYR1 rw

Toggle fields

AES_KEYR1

Bits 0-31: AES key register (key [63:32]).

KEYR2

key register 2

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AES_KEYR2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AES_KEYR2 rw

Toggle fields

AES_KEYR2

Bits 0-31: AES key register (key [95:64]).

KEYR3

key register 3

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AES_KEYR3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AES_KEYR3 rw

Toggle fields

AES_KEYR3

Bits 0-31: AES key register (MSB key [127:96]).

IVR0

initialization vector register 0

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AES_IVR0 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AES_IVR0 rw

Toggle fields

AES_IVR0

Bits 0-31: initialization vector register (LSB IVR [31:0]).

IVR1

initialization vector register 1

Offset: 0x24, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AES_IVR1 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AES_IVR1 rw

Toggle fields

AES_IVR1

Bits 0-31: Initialization Vector Register (IVR [63:32]).

IVR2

initialization vector register 2

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AES_IVR2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AES_IVR2 rw

Toggle fields

AES_IVR2

Bits 0-31: Initialization Vector Register (IVR [95:64]).

IVR3

initialization vector register 3

Offset: 0x2c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AES_IVR3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AES_IVR3 rw

Toggle fields

AES_IVR3

Bits 0-31: Initialization Vector Register (MSB IVR [127:96]).

KEYR4

key register 4

Offset: 0x30, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AES_KEYR4 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AES_KEYR4 rw

Toggle fields

AES_KEYR4

Bits 0-31: AES key register (MSB key [159:128]).

KEYR5

key register 5

Offset: 0x34, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AES_KEYR5 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AES_KEYR5 rw

Toggle fields

AES_KEYR5

Bits 0-31: AES key register (MSB key [191:160]).

KEYR6

key register 6

Offset: 0x38, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AES_KEYR6 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AES_KEYR6 rw

Toggle fields

AES_KEYR6

Bits 0-31: AES key register (MSB key [223:192]).

KEYR7

key register 7

Offset: 0x3c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AES_KEYR7 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AES_KEYR7 rw

Toggle fields

AES_KEYR7

Bits 0-31: AES key register (MSB key [255:224]).

SUSP0R

AES suspend register 0

Offset: 0x40, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AES_SUSP0R rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AES_SUSP0R rw

Toggle fields

AES_SUSP0R

Bits 0-31: AES suspend register 0.

SUSP1R

AES suspend register 1

Offset: 0x44, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AES_SUSP1R rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AES_SUSP1R rw

Toggle fields

AES_SUSP1R

Bits 0-31: AES suspend register 1.

SUSP2R

AES suspend register 2

Offset: 0x48, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AES_SUSP2R rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AES_SUSP2R rw

Toggle fields

AES_SUSP2R

Bits 0-31: AES suspend register 2.

SUSP3R

AES suspend register 3

Offset: 0x4c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AES_SUSP3R rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AES_SUSP3R rw

Toggle fields

AES_SUSP3R

Bits 0-31: AES suspend register 3.

SUSP4R

AES suspend register 4

Offset: 0x50, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AES_SUSP4R rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AES_SUSP4R rw

Toggle fields

AES_SUSP4R

Bits 0-31: AES suspend register 4.

SUSP5R

AES suspend register 5

Offset: 0x54, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AES_SUSP5R rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AES_SUSP5R rw

Toggle fields

AES_SUSP5R

Bits 0-31: AES suspend register 5.

SUSP6R

AES suspend register 6

Offset: 0x58, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AES_SUSP6R rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AES_SUSP6R rw

Toggle fields

AES_SUSP6R

Bits 0-31: AES suspend register 6.

SUSP7R

AES suspend register 7

Offset: 0x5c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AES_SUSP7R rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AES_SUSP7R rw

Toggle fields

AES_SUSP7R

Bits 0-31: AES suspend register 7.

CRC

0x40023000: Cyclic redundancy check calculation unit

0/8 fields covered.

Toggle register map

Offset	Name	31	15	7	6	4	0
0x0	DR	DR	DR
0x4	IDR	IDR	IDR
0x8	CR			REV_OUT	REV_IN	POLYSIZE	RESET
0x10	INIT	CRC_INIT	CRC_INIT
0x14	POL	POL	POL

Toggle registers

DR

Data register

Offset: 0x0, size: 32, reset: 0xFFFFFFFF, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
DR rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DR rw

Toggle fields

DR

Bits 0-31: Data register bits.

IDR

Independent data register

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
IDR rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IDR rw

Toggle fields

IDR

Bits 0-31: General-purpose 32-bit data register bits.

CR

Control register

Offset: 0x8, size: 32, reset: 0x00000000, access: Unspecified

0/4 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								REV_OUT rw	REV_IN rw		POLYSIZE rw				RESET w

Toggle fields

RESET

Bit 0: RESET bit.

POLYSIZE

Bits 3-4: Polynomial size.

REV_IN

Bits 5-6: Reverse input data.

REV_OUT

Bit 7: Reverse output data.

INIT

Initial CRC value

Offset: 0x10, size: 32, reset: 0xFFFFFFFF, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
CRC_INIT rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CRC_INIT rw

Toggle fields

CRC_INIT

Bits 0-31: Programmable initial CRC value.

POL

polynomial

Offset: 0x14, size: 32, reset: 0x04C11DB7, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
POL rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
POL rw

Toggle fields

POL

Bits 0-31: Programmable polynomial.

DBG

0x40015800: MCU debug component

2/16 fields covered.

Toggle register map

Offset	Name	31	30	21	18	17	15	12	11	10	2	1	0
0x0	IDCODE	REV_ID							DEV_ID
0x4	CR										DBG_STANDBY	DBG_STOP
0x8	APB_FZ1	DBG_LPTIM1_STOP	DBG_LPTIM2_STOP	DBG_I2C1_STOP				DBG_IWDG_STOP	DBG_WWDG_STOP	DBG_RTC_STOP		DBG_TIM3_STOP	DBG_TIM2_STOP
0xc	APB_FZ2				DBG_TIM17_STOP	DBG_TIM16_STOP	DBG_TIM14_STOP		DBG_TIM1_STOP

Toggle registers

IDCODE

DBGMCU_IDCODE

Offset: 0x0, size: 32, reset: 0x00000000, access: read-only

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
REV_ID r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				DEV_ID r

Toggle fields

DEV_ID

Bits 0-11: Device identifier.

REV_ID

Bits 16-31: Revision identifie.

CR

Debug MCU configuration register

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

0/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
													DBG_STANDBY rw	DBG_STOP rw

Toggle fields

DBG_STOP

Bit 1: Debug Stop mode.

DBG_STANDBY

Bit 2: Debug Standby mode.

APB_FZ1

Debug MCU APB1 freeze register1

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

0/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
DBG_LPTIM1_STOP rw	DBG_LPTIM2_STOP rw									DBG_I2C1_STOP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			DBG_IWDG_STOP rw	DBG_WWDG_STOP rw	DBG_RTC_STOP rw									DBG_TIM3_STOP rw	DBG_TIM2_STOP rw

Toggle fields

DBG_TIM2_STOP

Bit 0: TIM2 counter stopped when core is halted.

DBG_TIM3_STOP

Bit 1: TIM3 counter stopped when core is halted.

DBG_RTC_STOP

Bit 10: RTC counter stopped when core is halted.

DBG_WWDG_STOP

Bit 11: Window watchdog counter stopped when core is halted.

DBG_IWDG_STOP

Bit 12: Independent watchdog counter stopped when core is halted.

DBG_I2C1_STOP

Bit 21: I2C1 SMBUS timeout counter stopped when core is halted.

DBG_LPTIM2_STOP

Bit 30: LPTIM2 counter stopped when core is halted.

DBG_LPTIM1_STOP

Bit 31: LPTIM1 counter stopped when core is halted.

APB_FZ2

Debug MCU APB1 freeze register 2

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
													DBG_TIM17_STOP rw	DBG_TIM16_STOP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DBG_TIM14_STOP rw				DBG_TIM1_STOP rw

Toggle fields

DBG_TIM1_STOP

Bit 11: TIM1 counter stopped when core is halted.

DBG_TIM14_STOP

Bit 15: DBG_TIM14_STOP.

DBG_TIM16_STOP

Bit 17: DBG_TIM16_STOP.

DBG_TIM17_STOP

Bit 18: DBG_TIM17_STOP.

DMA1

0x40020000: DMA controller

105/115 fields covered.

Toggle register map

Offset	Name	31	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	ISR		TEIF[5]	HTIF[5]	TCIF[5]	GIF[5]	TEIF[4]	HTIF[4]	TCIF[4]	GIF[4]	TEIF[3]	HTIF[3]	TCIF[3]	GIF[3]	TEIF[2]	HTIF[2]	TCIF[2]	GIF[2]	TEIF[1]	HTIF[1]	TCIF[1]	GIF[1]
0x4	IFCR		CTEIF[5]	CHTIF[5]	CTCIF[5]	CGIF[5]	CTEIF[4]	CHTIF[4]	CTCIF[4]	CGIF[4]	CTEIF[3]	CHTIF[3]	CTCIF[3]	CGIF[3]	CTEIF[2]	CHTIF[2]	CTCIF[2]	CGIF[2]	CTEIF[1]	CHTIF[1]	CTCIF[1]	CGIF[1]
0x8	CR [1]							MEM2MEM	PL		MSIZE		PSIZE		MINC	PINC	CIRC	DIR	TEIE	HTIE	TCIE	EN
0xc	NDTR [1]						NDT
0x10	PAR [1]	PA					PA
0x14	MAR [1]	MA					MA
0x1c	CR [2]							MEM2MEM	PL		MSIZE		PSIZE		MINC	PINC	CIRC	DIR	TEIE	HTIE	TCIE	EN
0x20	NDTR [2]						NDT
0x24	PAR [2]	PA					PA
0x28	MAR [2]	MA					MA
0x30	CR [3]							MEM2MEM	PL		MSIZE		PSIZE		MINC	PINC	CIRC	DIR	TEIE	HTIE	TCIE	EN
0x34	NDTR [3]						NDT
0x38	PAR [3]	PA					PA
0x3c	MAR [3]	MA					MA
0x44	CR [4]							MEM2MEM	PL		MSIZE		PSIZE		MINC	PINC	CIRC	DIR	TEIE	HTIE	TCIE	EN
0x48	NDTR [4]						NDT
0x4c	PAR [4]	PA					PA
0x50	MAR [4]	MA					MA
0x58	CR [5]							MEM2MEM	PL		MSIZE		PSIZE		MINC	PINC	CIRC	DIR	TEIE	HTIE	TCIE	EN
0x5c	NDTR [5]						NDT
0x60	PAR [5]	PA					PA
0x64	MAR [5]	MA					MA

Toggle registers

ISR

DMA interrupt status register

Offset: 0x0, size: 32, reset: 0x00000000, access: Unspecified

20/20 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
												TEIF[5] r	HTIF[5] r	TCIF[5] r	GIF[5] r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TEIF[4] r	HTIF[4] r	TCIF[4] r	GIF[4] r	TEIF[3] r	HTIF[3] r	TCIF[3] r	GIF[3] r	TEIF[2] r	HTIF[2] r	TCIF[2] r	GIF[2] r	TEIF[1] r	HTIF[1] r	TCIF[1] r	GIF[1] r

Toggle fields

GIF[1]

Bit 0: Channel 1 Global interrupt flag.

Allowed values:
0: NoEvent: No transfer error, half event, complete event
1: Event: A transfer error, half event or complete event has occured

TCIF[1]

Bit 1: Channel 1 Transfer Complete flag.

Allowed values:
0: NotComplete: No transfer complete event
1: Complete: A transfer complete event has occured

HTIF[1]

Bit 2: Channel 1 Half Transfer Complete flag.

Allowed values:
0: NotHalf: No half transfer event
1: Half: A half transfer event has occured

TEIF[1]

Bit 3: Channel 1 Transfer Error flag.

Allowed values:
0: NoError: No transfer error
1: Error: A transfer error has occured

GIF[2]

Bit 4: Channel 2 Global interrupt flag.

Allowed values:
0: NoEvent: No transfer error, half event, complete event
1: Event: A transfer error, half event or complete event has occured

TCIF[2]

Bit 5: Channel 2 Transfer Complete flag.

Allowed values:
0: NotComplete: No transfer complete event
1: Complete: A transfer complete event has occured

HTIF[2]

Bit 6: Channel 2 Half Transfer Complete flag.

Allowed values:
0: NotHalf: No half transfer event
1: Half: A half transfer event has occured

TEIF[2]

Bit 7: Channel 2 Transfer Error flag.

Allowed values:
0: NoError: No transfer error
1: Error: A transfer error has occured

GIF[3]

Bit 8: Channel 3 Global interrupt flag.

Allowed values:
0: NoEvent: No transfer error, half event, complete event
1: Event: A transfer error, half event or complete event has occured

TCIF[3]

Bit 9: Channel 3 Transfer Complete flag.

Allowed values:
0: NotComplete: No transfer complete event
1: Complete: A transfer complete event has occured

HTIF[3]

Bit 10: Channel 3 Half Transfer Complete flag.

Allowed values:
0: NotHalf: No half transfer event
1: Half: A half transfer event has occured

TEIF[3]

Bit 11: Channel 3 Transfer Error flag.

Allowed values:
0: NoError: No transfer error
1: Error: A transfer error has occured

GIF[4]

Bit 12: Channel 4 Global interrupt flag.

Allowed values:
0: NoEvent: No transfer error, half event, complete event
1: Event: A transfer error, half event or complete event has occured

TCIF[4]

Bit 13: Channel 4 Transfer Complete flag.

Allowed values:
0: NotComplete: No transfer complete event
1: Complete: A transfer complete event has occured

HTIF[4]

Bit 14: Channel 4 Half Transfer Complete flag.

Allowed values:
0: NotHalf: No half transfer event
1: Half: A half transfer event has occured

TEIF[4]

Bit 15: Channel 4 Transfer Error flag.

Allowed values:
0: NoError: No transfer error
1: Error: A transfer error has occured

GIF[5]

Bit 16: Channel 5 Global interrupt flag.

Allowed values:
0: NoEvent: No transfer error, half event, complete event
1: Event: A transfer error, half event or complete event has occured

TCIF[5]

Bit 17: Channel 5 Transfer Complete flag.

Allowed values:
0: NotComplete: No transfer complete event
1: Complete: A transfer complete event has occured

HTIF[5]

Bit 18: Channel 5 Half Transfer Complete flag.

Allowed values:
0: NotHalf: No half transfer event
1: Half: A half transfer event has occured

TEIF[5]

Bit 19: Channel 5 Transfer Error flag.

Allowed values:
0: NoError: No transfer error
1: Error: A transfer error has occured

IFCR

DMA interrupt flag clear register

Offset: 0x4, size: 32, reset: 0x00000000, access: Unspecified

20/20 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
												CTEIF[5] w	CHTIF[5] w	CTCIF[5] w	CGIF[5] w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CTEIF[4] w	CHTIF[4] w	CTCIF[4] w	CGIF[4] w	CTEIF[3] w	CHTIF[3] w	CTCIF[3] w	CGIF[3] w	CTEIF[2] w	CHTIF[2] w	CTCIF[2] w	CGIF[2] w	CTEIF[1] w	CHTIF[1] w	CTCIF[1] w	CGIF[1] w

Toggle fields

CGIF[1]

Bit 0: Channel 1 Global interrupt clear.

Allowed values:
1: Clear: Clears the GIF, TEIF, HTIF, TCIF flags in the ISR register

CTCIF[1]

Bit 1: Channel 1 Transfer Complete clear.

Allowed values:
1: Clear: Clears the TCIF flag in the ISR register

CHTIF[1]

Bit 2: Channel 1 Half Transfer clear.

Allowed values:
1: Clear: Clears the HTIF flag in the ISR register

CTEIF[1]

Bit 3: Channel 1 Transfer Error clear.

Allowed values:
1: Clear: Clears the TEIF flag in the ISR register

CGIF[2]

Bit 4: Channel 2 Global interrupt clear.

Allowed values:
1: Clear: Clears the GIF, TEIF, HTIF, TCIF flags in the ISR register

CTCIF[2]

Bit 5: Channel 2 Transfer Complete clear.

Allowed values:
1: Clear: Clears the TCIF flag in the ISR register

CHTIF[2]

Bit 6: Channel 2 Half Transfer clear.

Allowed values:
1: Clear: Clears the HTIF flag in the ISR register

CTEIF[2]

Bit 7: Channel 2 Transfer Error clear.

Allowed values:
1: Clear: Clears the TEIF flag in the ISR register

CGIF[3]

Bit 8: Channel 3 Global interrupt clear.

Allowed values:
1: Clear: Clears the GIF, TEIF, HTIF, TCIF flags in the ISR register

CTCIF[3]

Bit 9: Channel 3 Transfer Complete clear.

Allowed values:
1: Clear: Clears the TCIF flag in the ISR register

CHTIF[3]

Bit 10: Channel 3 Half Transfer clear.

Allowed values:
1: Clear: Clears the HTIF flag in the ISR register

CTEIF[3]

Bit 11: Channel 3 Transfer Error clear.

Allowed values:
1: Clear: Clears the TEIF flag in the ISR register

CGIF[4]

Bit 12: Channel 4 Global interrupt clear.

Allowed values:
1: Clear: Clears the GIF, TEIF, HTIF, TCIF flags in the ISR register

CTCIF[4]

Bit 13: Channel 4 Transfer Complete clear.

Allowed values:
1: Clear: Clears the TCIF flag in the ISR register

CHTIF[4]

Bit 14: Channel 4 Half Transfer clear.

Allowed values:
1: Clear: Clears the HTIF flag in the ISR register

CTEIF[4]

Bit 15: Channel 4 Transfer Error clear.

Allowed values:
1: Clear: Clears the TEIF flag in the ISR register

CGIF[5]

Bit 16: Channel 5 Global interrupt clear.

Allowed values:
1: Clear: Clears the GIF, TEIF, HTIF, TCIF flags in the ISR register

CTCIF[5]

Bit 17: Channel 5 Transfer Complete clear.

Allowed values:
1: Clear: Clears the TCIF flag in the ISR register

CHTIF[5]

Bit 18: Channel 5 Half Transfer clear.

Allowed values:
1: Clear: Clears the HTIF flag in the ISR register

CTEIF[5]

Bit 19: Channel 5 Transfer Error clear.

Allowed values:
1: Clear: Clears the TEIF flag in the ISR register

CR [1]

DMA channel 1 configuration register

Offset: 0x8, size: 32, reset: 0x00000000, access: Unspecified

12/12 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	MEM2MEM rw	PL rw		MSIZE rw		PSIZE rw		MINC rw	PINC rw	CIRC rw	DIR rw	TEIE rw	HTIE rw	TCIE rw	EN rw

Toggle fields

EN

Bit 0: channel enable When a channel transfer error occurs, this bit is cleared by hardware. It can not be set again by software (channel x re-activated) until the TEIFx bit of the DMA_ISR register is cleared (by setting the CTEIFx bit of the DMA_IFCR register). Note: this bit is set and cleared by software..

Allowed values:
0: Disabled: Channel disabled
1: Enabled: Channel enabled

TCIE

Bit 1: transfer complete interrupt enable Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is not read-only when the channel is enabled (EN=1)..

Allowed values:
0: Disabled: Transfer Complete interrupt disabled
1: Enabled: Transfer Complete interrupt enabled

HTIE

Bit 2: half transfer interrupt enable Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is not read-only when the channel is enabled (EN=1)..

Allowed values:
0: Disabled: Half Transfer interrupt disabled
1: Enabled: Half Transfer interrupt enabled

TEIE

Bit 3: transfer error interrupt enable Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is not read-only when the channel is enabled (EN=1)..

Allowed values:
0: Disabled: Transfer Error interrupt disabled
1: Enabled: Transfer Error interrupt enabled

DIR

Bit 4: data transfer direction This bit must be set only in memory-to-peripheral and peripheral-to-memory modes. Source attributes are defined by PSIZE and PINC, plus the DMA_CPARx register. This is still valid in a memory-to-memory mode. Destination attributes are defined by MSIZE and MINC, plus the DMA_CMARx register. This is still valid in a peripheral-to-peripheral mode. Destination attributes are defined by PSIZE and PINC, plus the DMA_CPARx register. This is still valid in a memory-to-memory mode. Source attributes are defined by MSIZE and MINC, plus the DMA_CMARx register. This is still valid in a peripheral-to-peripheral mode. Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN=1)..

Allowed values:
0: FromPeripheral: Read from peripheral
1: FromMemory: Read from memory

CIRC

Bit 5: circular mode Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is not read-only when the channel is enabled (EN=1)..

Allowed values:
0: Disabled: Circular buffer disabled
1: Enabled: Circular buffer enabled

PINC

Bit 6: peripheral increment mode Defines the increment mode for each DMA transfer to the identified peripheral. n memory-to-memory mode, this field identifies the memory destination if DIR=1 and the memory source if DIR=0. In peripheral-to-peripheral mode, this field identifies the peripheral destination if DIR=1 and the peripheral source if DIR=0. Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN=1)..

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

MINC

Bit 7: memory increment mode Defines the increment mode for each DMA transfer to the identified memory. In memory-to-memory mode, this field identifies the memory source if DIR=1 and the memory destination if DIR=0. In peripheral-to-peripheral mode, this field identifies the peripheral source if DIR=1 and the peripheral destination if DIR=0. Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN=1)..

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

PSIZE

Bits 8-9: peripheral size Defines the data size of each DMA transfer to the identified peripheral. In memory-to-memory mode, this field identifies the memory destination if DIR=1 and the memory source if DIR=0. In peripheral-to-peripheral mode, this field identifies the peripheral destination if DIR=1 and the peripheral source if DIR=0. Note: this field is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN=1)..

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

MSIZE

Bits 10-11: memory size Defines the data size of each DMA transfer to the identified memory. In memory-to-memory mode, this field identifies the memory source if DIR=1 and the memory destination if DIR=0. In peripheral-to-peripheral mode, this field identifies the peripheral source if DIR=1 and the peripheral destination if DIR=0. Note: this field is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN=1)..

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

PL

Bits 12-13: priority level Note: this field is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN=1)..

Allowed values:
0: Low: Low priority
1: Medium: Medium priority
2: High: High priority
3: VeryHigh: Very high priority

MEM2MEM

Bit 14: memory-to-memory mode Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN=1)..

Allowed values:
0: Disabled: Memory to memory mode disabled
1: Enabled: Memory to memory mode enabled

NDTR [1]

DMA channel x number of data register

Offset: 0xc, size: 32, reset: 0x00000000, access: Unspecified

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
NDT rw

Toggle fields

NDT

Bits 0-15: number of data to transfer.

Allowed values: 0x0-0xffff

PAR [1]

DMA channel x peripheral address register

Offset: 0x10, size: 32, reset: 0x00000000, access: Unspecified

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PA rw

Toggle fields

PA

Bits 0-31: peripheral address It contains the base address of the peripheral data register from/to which the data will be read/written. When PSIZE[1:0]=01 (16 bits), bit 0 of PA[31:0] is ignored. Access is automatically aligned to a half-word address. When PSIZE=10 (32 bits), bits 1 and 0 of PA[31:0] are ignored. Access is automatically aligned to a word address. In memory-to-memory mode, this register identifies the memory destination address if DIR=1 and the memory source address if DIR=0. In peripheral-to-peripheral mode, this register identifies the peripheral destination address DIR=1 and the peripheral source address if DIR=0. Note: this register is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is not read-only when the channel is enabled (EN=1)..

MAR [1]

DMA channel x memory address register

Offset: 0x14, size: 32, reset: 0x00000000, access: Unspecified

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MA rw

Toggle fields

MA

Bits 0-31: peripheral address It contains the base address of the memory from/to which the data will be read/written. When MSIZE[1:0]=01 (16 bits), bit 0 of MA[31:0] is ignored. Access is automatically aligned to a half-word address. When MSIZE=10 (32 bits), bits 1 and 0 of MA[31:0] are ignored. Access is automatically aligned to a word address. In memory-to-memory mode, this register identifies the memory source address if DIR=1 and the memory destination address if DIR=0. In peripheral-to-peripheral mode, this register identifies the peripheral source address DIR=1 and the peripheral destination address if DIR=0. Note: this register is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is not read-only when the channel is enabled (EN=1)..

CR [2]

DMA channel 1 configuration register

Offset: 0x1c, size: 32, reset: 0x00000000, access: Unspecified

12/12 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	MEM2MEM rw	PL rw		MSIZE rw		PSIZE rw		MINC rw	PINC rw	CIRC rw	DIR rw	TEIE rw	HTIE rw	TCIE rw	EN rw

Toggle fields

EN

Bit 0: channel enable When a channel transfer error occurs, this bit is cleared by hardware. It can not be set again by software (channel x re-activated) until the TEIFx bit of the DMA_ISR register is cleared (by setting the CTEIFx bit of the DMA_IFCR register). Note: this bit is set and cleared by software..

Allowed values:
0: Disabled: Channel disabled
1: Enabled: Channel enabled

TCIE

Bit 1: transfer complete interrupt enable Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is not read-only when the channel is enabled (EN=1)..

Allowed values:
0: Disabled: Transfer Complete interrupt disabled
1: Enabled: Transfer Complete interrupt enabled

HTIE

Bit 2: half transfer interrupt enable Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is not read-only when the channel is enabled (EN=1)..

Allowed values:
0: Disabled: Half Transfer interrupt disabled
1: Enabled: Half Transfer interrupt enabled

TEIE

Bit 3: transfer error interrupt enable Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is not read-only when the channel is enabled (EN=1)..

Allowed values:
0: Disabled: Transfer Error interrupt disabled
1: Enabled: Transfer Error interrupt enabled

DIR

Bit 4: data transfer direction This bit must be set only in memory-to-peripheral and peripheral-to-memory modes. Source attributes are defined by PSIZE and PINC, plus the DMA_CPARx register. This is still valid in a memory-to-memory mode. Destination attributes are defined by MSIZE and MINC, plus the DMA_CMARx register. This is still valid in a peripheral-to-peripheral mode. Destination attributes are defined by PSIZE and PINC, plus the DMA_CPARx register. This is still valid in a memory-to-memory mode. Source attributes are defined by MSIZE and MINC, plus the DMA_CMARx register. This is still valid in a peripheral-to-peripheral mode. Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN=1)..

Allowed values:
0: FromPeripheral: Read from peripheral
1: FromMemory: Read from memory

CIRC

Bit 5: circular mode Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is not read-only when the channel is enabled (EN=1)..

Allowed values:
0: Disabled: Circular buffer disabled
1: Enabled: Circular buffer enabled

PINC

Bit 6: peripheral increment mode Defines the increment mode for each DMA transfer to the identified peripheral. n memory-to-memory mode, this field identifies the memory destination if DIR=1 and the memory source if DIR=0. In peripheral-to-peripheral mode, this field identifies the peripheral destination if DIR=1 and the peripheral source if DIR=0. Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN=1)..

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

MINC

Bit 7: memory increment mode Defines the increment mode for each DMA transfer to the identified memory. In memory-to-memory mode, this field identifies the memory source if DIR=1 and the memory destination if DIR=0. In peripheral-to-peripheral mode, this field identifies the peripheral source if DIR=1 and the peripheral destination if DIR=0. Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN=1)..

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

PSIZE

Bits 8-9: peripheral size Defines the data size of each DMA transfer to the identified peripheral. In memory-to-memory mode, this field identifies the memory destination if DIR=1 and the memory source if DIR=0. In peripheral-to-peripheral mode, this field identifies the peripheral destination if DIR=1 and the peripheral source if DIR=0. Note: this field is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN=1)..

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

MSIZE

Bits 10-11: memory size Defines the data size of each DMA transfer to the identified memory. In memory-to-memory mode, this field identifies the memory source if DIR=1 and the memory destination if DIR=0. In peripheral-to-peripheral mode, this field identifies the peripheral source if DIR=1 and the peripheral destination if DIR=0. Note: this field is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN=1)..

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

PL

Bits 12-13: priority level Note: this field is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN=1)..

Allowed values:
0: Low: Low priority
1: Medium: Medium priority
2: High: High priority
3: VeryHigh: Very high priority

MEM2MEM

Bit 14: memory-to-memory mode Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN=1)..

Allowed values:
0: Disabled: Memory to memory mode disabled
1: Enabled: Memory to memory mode enabled

NDTR [2]

DMA channel x number of data register

Offset: 0x20, size: 32, reset: 0x00000000, access: Unspecified

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
NDT rw

Toggle fields

NDT

Bits 0-15: number of data to transfer.

Allowed values: 0x0-0xffff

PAR [2]

DMA channel x peripheral address register

Offset: 0x24, size: 32, reset: 0x00000000, access: Unspecified

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PA rw

Toggle fields

PA

Bits 0-31: peripheral address It contains the base address of the peripheral data register from/to which the data will be read/written. When PSIZE[1:0]=01 (16 bits), bit 0 of PA[31:0] is ignored. Access is automatically aligned to a half-word address. When PSIZE=10 (32 bits), bits 1 and 0 of PA[31:0] are ignored. Access is automatically aligned to a word address. In memory-to-memory mode, this register identifies the memory destination address if DIR=1 and the memory source address if DIR=0. In peripheral-to-peripheral mode, this register identifies the peripheral destination address DIR=1 and the peripheral source address if DIR=0. Note: this register is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is not read-only when the channel is enabled (EN=1)..

MAR [2]

DMA channel x memory address register

Offset: 0x28, size: 32, reset: 0x00000000, access: Unspecified

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MA rw

Toggle fields

MA

Bits 0-31: peripheral address It contains the base address of the memory from/to which the data will be read/written. When MSIZE[1:0]=01 (16 bits), bit 0 of MA[31:0] is ignored. Access is automatically aligned to a half-word address. When MSIZE=10 (32 bits), bits 1 and 0 of MA[31:0] are ignored. Access is automatically aligned to a word address. In memory-to-memory mode, this register identifies the memory source address if DIR=1 and the memory destination address if DIR=0. In peripheral-to-peripheral mode, this register identifies the peripheral source address DIR=1 and the peripheral destination address if DIR=0. Note: this register is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is not read-only when the channel is enabled (EN=1)..

CR [3]

DMA channel 1 configuration register

Offset: 0x30, size: 32, reset: 0x00000000, access: Unspecified

12/12 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	MEM2MEM rw	PL rw		MSIZE rw		PSIZE rw		MINC rw	PINC rw	CIRC rw	DIR rw	TEIE rw	HTIE rw	TCIE rw	EN rw

Toggle fields

EN

Bit 0: channel enable When a channel transfer error occurs, this bit is cleared by hardware. It can not be set again by software (channel x re-activated) until the TEIFx bit of the DMA_ISR register is cleared (by setting the CTEIFx bit of the DMA_IFCR register). Note: this bit is set and cleared by software..

Allowed values:
0: Disabled: Channel disabled
1: Enabled: Channel enabled

TCIE

Bit 1: transfer complete interrupt enable Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is not read-only when the channel is enabled (EN=1)..

Allowed values:
0: Disabled: Transfer Complete interrupt disabled
1: Enabled: Transfer Complete interrupt enabled

HTIE

Bit 2: half transfer interrupt enable Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is not read-only when the channel is enabled (EN=1)..

Allowed values:
0: Disabled: Half Transfer interrupt disabled
1: Enabled: Half Transfer interrupt enabled

TEIE

Bit 3: transfer error interrupt enable Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is not read-only when the channel is enabled (EN=1)..

Allowed values:
0: Disabled: Transfer Error interrupt disabled
1: Enabled: Transfer Error interrupt enabled

DIR

Bit 4: data transfer direction This bit must be set only in memory-to-peripheral and peripheral-to-memory modes. Source attributes are defined by PSIZE and PINC, plus the DMA_CPARx register. This is still valid in a memory-to-memory mode. Destination attributes are defined by MSIZE and MINC, plus the DMA_CMARx register. This is still valid in a peripheral-to-peripheral mode. Destination attributes are defined by PSIZE and PINC, plus the DMA_CPARx register. This is still valid in a memory-to-memory mode. Source attributes are defined by MSIZE and MINC, plus the DMA_CMARx register. This is still valid in a peripheral-to-peripheral mode. Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN=1)..

Allowed values:
0: FromPeripheral: Read from peripheral
1: FromMemory: Read from memory

CIRC

Bit 5: circular mode Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is not read-only when the channel is enabled (EN=1)..

Allowed values:
0: Disabled: Circular buffer disabled
1: Enabled: Circular buffer enabled

PINC

Bit 6: peripheral increment mode Defines the increment mode for each DMA transfer to the identified peripheral. n memory-to-memory mode, this field identifies the memory destination if DIR=1 and the memory source if DIR=0. In peripheral-to-peripheral mode, this field identifies the peripheral destination if DIR=1 and the peripheral source if DIR=0. Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN=1)..

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

MINC

Bit 7: memory increment mode Defines the increment mode for each DMA transfer to the identified memory. In memory-to-memory mode, this field identifies the memory source if DIR=1 and the memory destination if DIR=0. In peripheral-to-peripheral mode, this field identifies the peripheral source if DIR=1 and the peripheral destination if DIR=0. Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN=1)..

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

PSIZE

Bits 8-9: peripheral size Defines the data size of each DMA transfer to the identified peripheral. In memory-to-memory mode, this field identifies the memory destination if DIR=1 and the memory source if DIR=0. In peripheral-to-peripheral mode, this field identifies the peripheral destination if DIR=1 and the peripheral source if DIR=0. Note: this field is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN=1)..

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

MSIZE

Bits 10-11: memory size Defines the data size of each DMA transfer to the identified memory. In memory-to-memory mode, this field identifies the memory source if DIR=1 and the memory destination if DIR=0. In peripheral-to-peripheral mode, this field identifies the peripheral source if DIR=1 and the peripheral destination if DIR=0. Note: this field is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN=1)..

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

PL

Bits 12-13: priority level Note: this field is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN=1)..

Allowed values:
0: Low: Low priority
1: Medium: Medium priority
2: High: High priority
3: VeryHigh: Very high priority

MEM2MEM

Bit 14: memory-to-memory mode Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN=1)..

Allowed values:
0: Disabled: Memory to memory mode disabled
1: Enabled: Memory to memory mode enabled

NDTR [3]

DMA channel x number of data register

Offset: 0x34, size: 32, reset: 0x00000000, access: Unspecified

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
NDT rw

Toggle fields

NDT

Bits 0-15: number of data to transfer.

Allowed values: 0x0-0xffff

PAR [3]

DMA channel x peripheral address register

Offset: 0x38, size: 32, reset: 0x00000000, access: Unspecified

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PA rw

Toggle fields

PA

Bits 0-31: peripheral address It contains the base address of the peripheral data register from/to which the data will be read/written. When PSIZE[1:0]=01 (16 bits), bit 0 of PA[31:0] is ignored. Access is automatically aligned to a half-word address. When PSIZE=10 (32 bits), bits 1 and 0 of PA[31:0] are ignored. Access is automatically aligned to a word address. In memory-to-memory mode, this register identifies the memory destination address if DIR=1 and the memory source address if DIR=0. In peripheral-to-peripheral mode, this register identifies the peripheral destination address DIR=1 and the peripheral source address if DIR=0. Note: this register is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is not read-only when the channel is enabled (EN=1)..

MAR [3]

DMA channel x memory address register

Offset: 0x3c, size: 32, reset: 0x00000000, access: Unspecified

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MA rw

Toggle fields

MA

Bits 0-31: peripheral address It contains the base address of the memory from/to which the data will be read/written. When MSIZE[1:0]=01 (16 bits), bit 0 of MA[31:0] is ignored. Access is automatically aligned to a half-word address. When MSIZE=10 (32 bits), bits 1 and 0 of MA[31:0] are ignored. Access is automatically aligned to a word address. In memory-to-memory mode, this register identifies the memory source address if DIR=1 and the memory destination address if DIR=0. In peripheral-to-peripheral mode, this register identifies the peripheral source address DIR=1 and the peripheral destination address if DIR=0. Note: this register is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is not read-only when the channel is enabled (EN=1)..

CR [4]

DMA channel 1 configuration register

Offset: 0x44, size: 32, reset: 0x00000000, access: Unspecified

12/12 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	MEM2MEM rw	PL rw		MSIZE rw		PSIZE rw		MINC rw	PINC rw	CIRC rw	DIR rw	TEIE rw	HTIE rw	TCIE rw	EN rw

Toggle fields

EN

Bit 0: channel enable When a channel transfer error occurs, this bit is cleared by hardware. It can not be set again by software (channel x re-activated) until the TEIFx bit of the DMA_ISR register is cleared (by setting the CTEIFx bit of the DMA_IFCR register). Note: this bit is set and cleared by software..

Allowed values:
0: Disabled: Channel disabled
1: Enabled: Channel enabled

TCIE

Bit 1: transfer complete interrupt enable Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is not read-only when the channel is enabled (EN=1)..

Allowed values:
0: Disabled: Transfer Complete interrupt disabled
1: Enabled: Transfer Complete interrupt enabled

HTIE

Bit 2: half transfer interrupt enable Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is not read-only when the channel is enabled (EN=1)..

Allowed values:
0: Disabled: Half Transfer interrupt disabled
1: Enabled: Half Transfer interrupt enabled

TEIE

Bit 3: transfer error interrupt enable Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is not read-only when the channel is enabled (EN=1)..

Allowed values:
0: Disabled: Transfer Error interrupt disabled
1: Enabled: Transfer Error interrupt enabled

DIR

Bit 4: data transfer direction This bit must be set only in memory-to-peripheral and peripheral-to-memory modes. Source attributes are defined by PSIZE and PINC, plus the DMA_CPARx register. This is still valid in a memory-to-memory mode. Destination attributes are defined by MSIZE and MINC, plus the DMA_CMARx register. This is still valid in a peripheral-to-peripheral mode. Destination attributes are defined by PSIZE and PINC, plus the DMA_CPARx register. This is still valid in a memory-to-memory mode. Source attributes are defined by MSIZE and MINC, plus the DMA_CMARx register. This is still valid in a peripheral-to-peripheral mode. Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN=1)..

Allowed values:
0: FromPeripheral: Read from peripheral
1: FromMemory: Read from memory

CIRC

Bit 5: circular mode Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is not read-only when the channel is enabled (EN=1)..

Allowed values:
0: Disabled: Circular buffer disabled
1: Enabled: Circular buffer enabled

PINC

Bit 6: peripheral increment mode Defines the increment mode for each DMA transfer to the identified peripheral. n memory-to-memory mode, this field identifies the memory destination if DIR=1 and the memory source if DIR=0. In peripheral-to-peripheral mode, this field identifies the peripheral destination if DIR=1 and the peripheral source if DIR=0. Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN=1)..

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

MINC

Bit 7: memory increment mode Defines the increment mode for each DMA transfer to the identified memory. In memory-to-memory mode, this field identifies the memory source if DIR=1 and the memory destination if DIR=0. In peripheral-to-peripheral mode, this field identifies the peripheral source if DIR=1 and the peripheral destination if DIR=0. Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN=1)..

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

PSIZE

Bits 8-9: peripheral size Defines the data size of each DMA transfer to the identified peripheral. In memory-to-memory mode, this field identifies the memory destination if DIR=1 and the memory source if DIR=0. In peripheral-to-peripheral mode, this field identifies the peripheral destination if DIR=1 and the peripheral source if DIR=0. Note: this field is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN=1)..

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

MSIZE

Bits 10-11: memory size Defines the data size of each DMA transfer to the identified memory. In memory-to-memory mode, this field identifies the memory source if DIR=1 and the memory destination if DIR=0. In peripheral-to-peripheral mode, this field identifies the peripheral source if DIR=1 and the peripheral destination if DIR=0. Note: this field is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN=1)..

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

PL

Bits 12-13: priority level Note: this field is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN=1)..

Allowed values:
0: Low: Low priority
1: Medium: Medium priority
2: High: High priority
3: VeryHigh: Very high priority

MEM2MEM

Bit 14: memory-to-memory mode Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN=1)..

Allowed values:
0: Disabled: Memory to memory mode disabled
1: Enabled: Memory to memory mode enabled

NDTR [4]

DMA channel x number of data register

Offset: 0x48, size: 32, reset: 0x00000000, access: Unspecified

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
NDT rw

Toggle fields

NDT

Bits 0-15: number of data to transfer.

Allowed values: 0x0-0xffff

PAR [4]

DMA channel x peripheral address register

Offset: 0x4c, size: 32, reset: 0x00000000, access: Unspecified

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PA rw

Toggle fields

PA

Bits 0-31: peripheral address It contains the base address of the peripheral data register from/to which the data will be read/written. When PSIZE[1:0]=01 (16 bits), bit 0 of PA[31:0] is ignored. Access is automatically aligned to a half-word address. When PSIZE=10 (32 bits), bits 1 and 0 of PA[31:0] are ignored. Access is automatically aligned to a word address. In memory-to-memory mode, this register identifies the memory destination address if DIR=1 and the memory source address if DIR=0. In peripheral-to-peripheral mode, this register identifies the peripheral destination address DIR=1 and the peripheral source address if DIR=0. Note: this register is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is not read-only when the channel is enabled (EN=1)..

MAR [4]

DMA channel x memory address register

Offset: 0x50, size: 32, reset: 0x00000000, access: Unspecified

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MA rw

Toggle fields

MA

Bits 0-31: peripheral address It contains the base address of the memory from/to which the data will be read/written. When MSIZE[1:0]=01 (16 bits), bit 0 of MA[31:0] is ignored. Access is automatically aligned to a half-word address. When MSIZE=10 (32 bits), bits 1 and 0 of MA[31:0] are ignored. Access is automatically aligned to a word address. In memory-to-memory mode, this register identifies the memory source address if DIR=1 and the memory destination address if DIR=0. In peripheral-to-peripheral mode, this register identifies the peripheral source address DIR=1 and the peripheral destination address if DIR=0. Note: this register is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is not read-only when the channel is enabled (EN=1)..

CR [5]

DMA channel 1 configuration register

Offset: 0x58, size: 32, reset: 0x00000000, access: Unspecified

12/12 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	MEM2MEM rw	PL rw		MSIZE rw		PSIZE rw		MINC rw	PINC rw	CIRC rw	DIR rw	TEIE rw	HTIE rw	TCIE rw	EN rw

Toggle fields

EN

Bit 0: channel enable When a channel transfer error occurs, this bit is cleared by hardware. It can not be set again by software (channel x re-activated) until the TEIFx bit of the DMA_ISR register is cleared (by setting the CTEIFx bit of the DMA_IFCR register). Note: this bit is set and cleared by software..

Allowed values:
0: Disabled: Channel disabled
1: Enabled: Channel enabled

TCIE

Bit 1: transfer complete interrupt enable Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is not read-only when the channel is enabled (EN=1)..

Allowed values:
0: Disabled: Transfer Complete interrupt disabled
1: Enabled: Transfer Complete interrupt enabled

HTIE

Bit 2: half transfer interrupt enable Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is not read-only when the channel is enabled (EN=1)..

Allowed values:
0: Disabled: Half Transfer interrupt disabled
1: Enabled: Half Transfer interrupt enabled

TEIE

Bit 3: transfer error interrupt enable Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is not read-only when the channel is enabled (EN=1)..

Allowed values:
0: Disabled: Transfer Error interrupt disabled
1: Enabled: Transfer Error interrupt enabled

DIR

Bit 4: data transfer direction This bit must be set only in memory-to-peripheral and peripheral-to-memory modes. Source attributes are defined by PSIZE and PINC, plus the DMA_CPARx register. This is still valid in a memory-to-memory mode. Destination attributes are defined by MSIZE and MINC, plus the DMA_CMARx register. This is still valid in a peripheral-to-peripheral mode. Destination attributes are defined by PSIZE and PINC, plus the DMA_CPARx register. This is still valid in a memory-to-memory mode. Source attributes are defined by MSIZE and MINC, plus the DMA_CMARx register. This is still valid in a peripheral-to-peripheral mode. Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN=1)..

Allowed values:
0: FromPeripheral: Read from peripheral
1: FromMemory: Read from memory

CIRC

Bit 5: circular mode Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is not read-only when the channel is enabled (EN=1)..

Allowed values:
0: Disabled: Circular buffer disabled
1: Enabled: Circular buffer enabled

PINC

Bit 6: peripheral increment mode Defines the increment mode for each DMA transfer to the identified peripheral. n memory-to-memory mode, this field identifies the memory destination if DIR=1 and the memory source if DIR=0. In peripheral-to-peripheral mode, this field identifies the peripheral destination if DIR=1 and the peripheral source if DIR=0. Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN=1)..

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

MINC

Bit 7: memory increment mode Defines the increment mode for each DMA transfer to the identified memory. In memory-to-memory mode, this field identifies the memory source if DIR=1 and the memory destination if DIR=0. In peripheral-to-peripheral mode, this field identifies the peripheral source if DIR=1 and the peripheral destination if DIR=0. Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN=1)..

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

PSIZE

Bits 8-9: peripheral size Defines the data size of each DMA transfer to the identified peripheral. In memory-to-memory mode, this field identifies the memory destination if DIR=1 and the memory source if DIR=0. In peripheral-to-peripheral mode, this field identifies the peripheral destination if DIR=1 and the peripheral source if DIR=0. Note: this field is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN=1)..

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

MSIZE

Bits 10-11: memory size Defines the data size of each DMA transfer to the identified memory. In memory-to-memory mode, this field identifies the memory source if DIR=1 and the memory destination if DIR=0. In peripheral-to-peripheral mode, this field identifies the peripheral source if DIR=1 and the peripheral destination if DIR=0. Note: this field is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN=1)..

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

PL

Bits 12-13: priority level Note: this field is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN=1)..

Allowed values:
0: Low: Low priority
1: Medium: Medium priority
2: High: High priority
3: VeryHigh: Very high priority

MEM2MEM

Bit 14: memory-to-memory mode Note: this bit is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is read-only when the channel is enabled (EN=1)..

Allowed values:
0: Disabled: Memory to memory mode disabled
1: Enabled: Memory to memory mode enabled

NDTR [5]

DMA channel x number of data register

Offset: 0x5c, size: 32, reset: 0x00000000, access: Unspecified

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
NDT rw

Toggle fields

NDT

Bits 0-15: number of data to transfer.

Allowed values: 0x0-0xffff

PAR [5]

DMA channel x peripheral address register

Offset: 0x60, size: 32, reset: 0x00000000, access: Unspecified

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PA rw

Toggle fields

PA

Bits 0-31: peripheral address It contains the base address of the peripheral data register from/to which the data will be read/written. When PSIZE[1:0]=01 (16 bits), bit 0 of PA[31:0] is ignored. Access is automatically aligned to a half-word address. When PSIZE=10 (32 bits), bits 1 and 0 of PA[31:0] are ignored. Access is automatically aligned to a word address. In memory-to-memory mode, this register identifies the memory destination address if DIR=1 and the memory source address if DIR=0. In peripheral-to-peripheral mode, this register identifies the peripheral destination address DIR=1 and the peripheral source address if DIR=0. Note: this register is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is not read-only when the channel is enabled (EN=1)..

MAR [5]

DMA channel x memory address register

Offset: 0x64, size: 32, reset: 0x00000000, access: Unspecified

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MA rw

Toggle fields

MA

Bits 0-31: peripheral address It contains the base address of the memory from/to which the data will be read/written. When MSIZE[1:0]=01 (16 bits), bit 0 of MA[31:0] is ignored. Access is automatically aligned to a half-word address. When MSIZE=10 (32 bits), bits 1 and 0 of MA[31:0] are ignored. Access is automatically aligned to a word address. In memory-to-memory mode, this register identifies the memory source address if DIR=1 and the memory destination address if DIR=0. In peripheral-to-peripheral mode, this register identifies the peripheral source address DIR=1 and the peripheral destination address if DIR=0. Note: this register is set and cleared by software. It must not be written when the channel is enabled (EN = 1). It is not read-only when the channel is enabled (EN=1)..

DMAMUX

0x40020800: DMAMUX

1/71 fields covered.

Toggle register map

Offset	Name	28	23	18	16	9	8	7	4	3
0x0	CCR[0]	SYNC_ID	NBREQ	SPOL	SE	EGE	SOIE	DMAREQ_ID
0x4	CCR[1]	SYNC_ID	NBREQ	SPOL	SE	EGE	SOIE	DMAREQ_ID
0x8	CCR[2]	SYNC_ID	NBREQ	SPOL	SE	EGE	SOIE	DMAREQ_ID
0xc	CCR[3]	SYNC_ID	NBREQ	SPOL	SE	EGE	SOIE	DMAREQ_ID
0x10	CCR[4]	SYNC_ID	NBREQ	SPOL	SE	EGE	SOIE	DMAREQ_ID
0x14	CCR[5]	SYNC_ID	NBREQ	SPOL	SE	EGE	SOIE	DMAREQ_ID
0x18	CCR[6]	SYNC_ID	NBREQ	SPOL	SE	EGE	SOIE	DMAREQ_ID
0x100	RGCR[0]		GNBREQ	GPOL	GE		OIE		SIG_ID
0x104	RGCR[1]		GNBREQ	GPOL	GE		OIE		SIG_ID
0x108	RGCR[2]		GNBREQ	GPOL	GE		OIE		SIG_ID
0x10c	RGCR[3]		GNBREQ	GPOL	GE		OIE		SIG_ID
0x140	RGSR									OF
0x144	RGCFR									COF

Toggle registers

CCR[0]

DMA Multiplexer Channel 0 Control register

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

0/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
			SYNC_ID rw					NBREQ rw					SPOL rw		SE rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						EGE rw	SOIE rw	DMAREQ_ID rw

Toggle fields

DMAREQ_ID

Bits 0-7: Input DMA request line selected.

SOIE

Bit 8: Interrupt enable at synchronization event overrun.

EGE

Bit 9: Event generation enable/disable.

SE

Bit 16: Synchronous operating mode enable/disable.

SPOL

Bits 17-18: Synchronization event type selector Defines the synchronization event on the selected synchronization input:.

NBREQ

Bits 19-23: Number of DMA requests to forward Defines the number of DMA requests forwarded before output event is generated. In synchronous mode, it also defines the number of DMA requests to forward after a synchronization event, then stop forwarding. The actual number of DMA requests forwarded is NBREQ+1. Note: This field can only be written when both SE and EGE bits are reset..

SYNC_ID

Bits 24-28: Synchronization input selected.

CCR[1]

DMA Multiplexer Channel 1 Control register

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

0/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
			SYNC_ID rw					NBREQ rw					SPOL rw		SE rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						EGE rw	SOIE rw	DMAREQ_ID rw

Toggle fields

DMAREQ_ID

Bits 0-7: Input DMA request line selected.

SOIE

Bit 8: Interrupt enable at synchronization event overrun.

EGE

Bit 9: Event generation enable/disable.

SE

Bit 16: Synchronous operating mode enable/disable.

SPOL

Bits 17-18: Synchronization event type selector Defines the synchronization event on the selected synchronization input:.

NBREQ

Bits 19-23: Number of DMA requests to forward Defines the number of DMA requests forwarded before output event is generated. In synchronous mode, it also defines the number of DMA requests to forward after a synchronization event, then stop forwarding. The actual number of DMA requests forwarded is NBREQ+1. Note: This field can only be written when both SE and EGE bits are reset..

SYNC_ID

Bits 24-28: Synchronization input selected.

CCR[2]

DMA Multiplexer Channel 2 Control register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

0/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
			SYNC_ID rw					NBREQ rw					SPOL rw		SE rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						EGE rw	SOIE rw	DMAREQ_ID rw

Toggle fields

DMAREQ_ID

Bits 0-7: Input DMA request line selected.

SOIE

Bit 8: Interrupt enable at synchronization event overrun.

EGE

Bit 9: Event generation enable/disable.

SE

Bit 16: Synchronous operating mode enable/disable.

SPOL

Bits 17-18: Synchronization event type selector Defines the synchronization event on the selected synchronization input:.

NBREQ

Bits 19-23: Number of DMA requests to forward Defines the number of DMA requests forwarded before output event is generated. In synchronous mode, it also defines the number of DMA requests to forward after a synchronization event, then stop forwarding. The actual number of DMA requests forwarded is NBREQ+1. Note: This field can only be written when both SE and EGE bits are reset..

SYNC_ID

Bits 24-28: Synchronization input selected.

CCR[3]

DMA Multiplexer Channel 3 Control register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

0/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
			SYNC_ID rw					NBREQ rw					SPOL rw		SE rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						EGE rw	SOIE rw	DMAREQ_ID rw

Toggle fields

DMAREQ_ID

Bits 0-7: Input DMA request line selected.

SOIE

Bit 8: Interrupt enable at synchronization event overrun.

EGE

Bit 9: Event generation enable/disable.

SE

Bit 16: Synchronous operating mode enable/disable.

SPOL

Bits 17-18: Synchronization event type selector Defines the synchronization event on the selected synchronization input:.

NBREQ

Bits 19-23: Number of DMA requests to forward Defines the number of DMA requests forwarded before output event is generated. In synchronous mode, it also defines the number of DMA requests to forward after a synchronization event, then stop forwarding. The actual number of DMA requests forwarded is NBREQ+1. Note: This field can only be written when both SE and EGE bits are reset..

SYNC_ID

Bits 24-28: Synchronization input selected.

CCR[4]

DMA Multiplexer Channel 4 Control register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

0/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
			SYNC_ID rw					NBREQ rw					SPOL rw		SE rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						EGE rw	SOIE rw	DMAREQ_ID rw

Toggle fields

DMAREQ_ID

Bits 0-7: Input DMA request line selected.

SOIE

Bit 8: Interrupt enable at synchronization event overrun.

EGE

Bit 9: Event generation enable/disable.

SE

Bit 16: Synchronous operating mode enable/disable.

SPOL

Bits 17-18: Synchronization event type selector Defines the synchronization event on the selected synchronization input:.

NBREQ

Bits 19-23: Number of DMA requests to forward Defines the number of DMA requests forwarded before output event is generated. In synchronous mode, it also defines the number of DMA requests to forward after a synchronization event, then stop forwarding. The actual number of DMA requests forwarded is NBREQ+1. Note: This field can only be written when both SE and EGE bits are reset..

SYNC_ID

Bits 24-28: Synchronization input selected.

CCR[5]

DMA Multiplexer Channel 5 Control register

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

0/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
			SYNC_ID rw					NBREQ rw					SPOL rw		SE rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						EGE rw	SOIE rw	DMAREQ_ID rw

Toggle fields

DMAREQ_ID

Bits 0-7: Input DMA request line selected.

SOIE

Bit 8: Interrupt enable at synchronization event overrun.

EGE

Bit 9: Event generation enable/disable.

SE

Bit 16: Synchronous operating mode enable/disable.

SPOL

Bits 17-18: Synchronization event type selector Defines the synchronization event on the selected synchronization input:.

NBREQ

Bits 19-23: Number of DMA requests to forward Defines the number of DMA requests forwarded before output event is generated. In synchronous mode, it also defines the number of DMA requests to forward after a synchronization event, then stop forwarding. The actual number of DMA requests forwarded is NBREQ+1. Note: This field can only be written when both SE and EGE bits are reset..

SYNC_ID

Bits 24-28: Synchronization input selected.

CCR[6]

DMA Multiplexer Channel 6 Control register

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

0/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
			SYNC_ID rw					NBREQ rw					SPOL rw		SE rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						EGE rw	SOIE rw	DMAREQ_ID rw

Toggle fields

DMAREQ_ID

Bits 0-7: Input DMA request line selected.

SOIE

Bit 8: Interrupt enable at synchronization event overrun.

EGE

Bit 9: Event generation enable/disable.

SE

Bit 16: Synchronous operating mode enable/disable.

SPOL

Bits 17-18: Synchronization event type selector Defines the synchronization event on the selected synchronization input:.

NBREQ

Bits 19-23: Number of DMA requests to forward Defines the number of DMA requests forwarded before output event is generated. In synchronous mode, it also defines the number of DMA requests to forward after a synchronization event, then stop forwarding. The actual number of DMA requests forwarded is NBREQ+1. Note: This field can only be written when both SE and EGE bits are reset..

SYNC_ID

Bits 24-28: Synchronization input selected.

RGCR[0]

DMAMux - DMA request generator channel x control register

Offset: 0x100, size: 32, reset: 0x00000000, access: read-write

0/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								GNBREQ rw					GPOL rw		GE rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							OIE rw				SIG_ID rw

Toggle fields

SIG_ID

Bits 0-4: DMA request trigger input selected.

OIE

Bit 8: Interrupt enable at trigger event overrun.

GE

Bit 16: DMA request generator channel enable/disable.

GPOL

Bits 17-18: DMA request generator trigger event type selection Defines the trigger event on the selected DMA request trigger input.

GNBREQ

Bits 19-23: Number of DMA requests to generate Defines the number of DMA requests generated after a trigger event, then stop generating. The actual number of generated DMA requests is GNBREQ+1. Note: This field can only be written when GE bit is reset..

RGCR[1]

DMAMux - DMA request generator channel x control register

Offset: 0x104, size: 32, reset: 0x00000000, access: read-write

0/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								GNBREQ rw					GPOL rw		GE rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							OIE rw				SIG_ID rw

Toggle fields

SIG_ID

Bits 0-4: DMA request trigger input selected.

OIE

Bit 8: Interrupt enable at trigger event overrun.

GE

Bit 16: DMA request generator channel enable/disable.

GPOL

Bits 17-18: DMA request generator trigger event type selection Defines the trigger event on the selected DMA request trigger input.

GNBREQ

Bits 19-23: Number of DMA requests to generate Defines the number of DMA requests generated after a trigger event, then stop generating. The actual number of generated DMA requests is GNBREQ+1. Note: This field can only be written when GE bit is reset..

RGCR[2]

DMAMux - DMA request generator channel x control register

Offset: 0x108, size: 32, reset: 0x00000000, access: read-write

0/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								GNBREQ rw					GPOL rw		GE rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							OIE rw				SIG_ID rw

Toggle fields

SIG_ID

Bits 0-4: DMA request trigger input selected.

OIE

Bit 8: Interrupt enable at trigger event overrun.

GE

Bit 16: DMA request generator channel enable/disable.

GPOL

Bits 17-18: DMA request generator trigger event type selection Defines the trigger event on the selected DMA request trigger input.

GNBREQ

Bits 19-23: Number of DMA requests to generate Defines the number of DMA requests generated after a trigger event, then stop generating. The actual number of generated DMA requests is GNBREQ+1. Note: This field can only be written when GE bit is reset..

RGCR[3]

DMAMux - DMA request generator channel x control register

Offset: 0x10c, size: 32, reset: 0x00000000, access: read-write

0/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								GNBREQ rw					GPOL rw		GE rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							OIE rw				SIG_ID rw

Toggle fields

SIG_ID

Bits 0-4: DMA request trigger input selected.

OIE

Bit 8: Interrupt enable at trigger event overrun.

GE

Bit 16: DMA request generator channel enable/disable.

GPOL

Bits 17-18: DMA request generator trigger event type selection Defines the trigger event on the selected DMA request trigger input.

GNBREQ

Bits 19-23: Number of DMA requests to generate Defines the number of DMA requests generated after a trigger event, then stop generating. The actual number of generated DMA requests is GNBREQ+1. Note: This field can only be written when GE bit is reset..

RGSR

DMAMux - DMA request generator status register

Offset: 0x140, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
												OF r

Toggle fields

OF

Bits 0-3: Trigger event overrun flag The flag is set when a trigger event occurs on DMA request generator channel x, while the DMA request generator counter value is lower than GNBREQ. The flag is cleared by writing 1 to the corresponding COFx bit in DMAMUX_RGCFR register..

RGCFR

DMAMux - DMA request generator clear flag register

Offset: 0x144, size: 32, reset: 0x00000000, access: write-only

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
												COF w

Toggle fields

COF

Bits 0-3: Clear trigger event overrun flag Upon setting, this bit clears the corresponding overrun flag OFx in the DMAMUX_RGCSR register..

EXTI

0x40021800: External interrupt/event controller

156/156 fields covered.

Toggle register map

Offset	Name	31	30	29	28	26	25	24	23	22	21	20	19	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	RTSR1													TR16	TR15	TR14	TR13	TR12	TR11	TR10	TR9	TR8	TR7	TR6	TR5	TR4	TR3	TR2	TR1	TR0
0x4	FTSR1													TR16	TR15	TR14	TR13	TR12	TR11	TR10	TR9	TR8	TR7	TR6	TR5	TR4	TR3	TR2	TR1	TR0
0x8	SWIER1													SWIER16	SWIER15	SWIER14	SWIER13	SWIER12	SWIER11	SWIER10	SWIER9	SWIER8	SWIER7	SWIER6	SWIER5	SWIER4	SWIER3	SWIER2	SWIER1	SWIER0
0xc	RPR1													RPIF16	RPIF15	RPIF14	RPIF13	RPIF12	RPIF11	RPIF10	RPIF9	RPIF8	RPIF7	RPIF6	RPIF5	RPIF4	RPIF3	RPIF2	RPIF1	RPIF0
0x10	FPR1													FPIF16	FPIF15	FPIF14	FPIF13	FPIF12	FPIF11	FPIF10	FPIF9	FPIF8	FPIF7	FPIF6	FPIF5	FPIF4	FPIF3	FPIF2	FPIF1	FPIF0
0x60	EXTICR1	EXTI24_31							EXTI16_23						EXTI8_15								EXTI0_7
0x64	EXTICR2	EXTI24_31							EXTI16_23						EXTI8_15								EXTI0_7
0x68	EXTICR3	EXTI24_31							EXTI16_23						EXTI8_15								EXTI0_7
0x6c	EXTICR4	EXTI24_31							EXTI16_23						EXTI8_15								EXTI0_7
0x80	IMR1	IM31	IM30	IM29	IM28	IM26	IM25	IM24	IM23	IM22	IM21	IM20	IM19	IM16	IM15	IM14	IM13	IM12	IM11	IM10	IM9	IM8	IM7	IM6	IM5	IM4	IM3	IM2	IM1	IM0
0x84	EMR1	EM31	EM30	EM29	EM28	EM26	EM25		EM23		EM21		EM19	EM16	EM15	EM14	EM13	EM12	EM11	EM10	EM9	EM8	EM7	EM6	EM5	EM4	EM3	EM2	EM1	EM0

Toggle registers

RTSR1

EXTI rising trigger selection register

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

17/17 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															TR16 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TR15 rw	TR14 rw	TR13 rw	TR12 rw	TR11 rw	TR10 rw	TR9 rw	TR8 rw	TR7 rw	TR6 rw	TR5 rw	TR4 rw	TR3 rw	TR2 rw	TR1 rw	TR0 rw

Toggle fields

TR0

Bit 0: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR1

Bit 1: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR2

Bit 2: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR3

Bit 3: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR4

Bit 4: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR5

Bit 5: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR6

Bit 6: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR7

Bit 7: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR8

Bit 8: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR9

Bit 9: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR10

Bit 10: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR11

Bit 11: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR12

Bit 12: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR13

Bit 13: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR14

Bit 14: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR15

Bit 15: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR16

Bit 16: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

FTSR1

EXTI falling trigger selection register

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

17/17 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															TR16 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TR15 rw	TR14 rw	TR13 rw	TR12 rw	TR11 rw	TR10 rw	TR9 rw	TR8 rw	TR7 rw	TR6 rw	TR5 rw	TR4 rw	TR3 rw	TR2 rw	TR1 rw	TR0 rw

Toggle fields

TR0

Bit 0: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR1

Bit 1: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR2

Bit 2: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR3

Bit 3: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR4

Bit 4: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR5

Bit 5: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR6

Bit 6: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR7

Bit 7: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR8

Bit 8: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR9

Bit 9: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR10

Bit 10: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR11

Bit 11: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR12

Bit 12: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR13

Bit 13: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR14

Bit 14: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR15

Bit 15: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR16

Bit 16: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

SWIER1

EXTI software interrupt event register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

17/17 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															SWIER16 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SWIER15 rw	SWIER14 rw	SWIER13 rw	SWIER12 rw	SWIER11 rw	SWIER10 rw	SWIER9 rw	SWIER8 rw	SWIER7 rw	SWIER6 rw	SWIER5 rw	SWIER4 rw	SWIER3 rw	SWIER2 rw	SWIER1 rw	SWIER0 rw

Toggle fields

SWIER0

Bit 0: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
1: Pend: Generates an interrupt request

SWIER1

Bit 1: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
1: Pend: Generates an interrupt request

SWIER2

Bit 2: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
1: Pend: Generates an interrupt request

SWIER3

Bit 3: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
1: Pend: Generates an interrupt request

SWIER4

Bit 4: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
1: Pend: Generates an interrupt request

SWIER5

Bit 5: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
1: Pend: Generates an interrupt request

SWIER6

Bit 6: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
1: Pend: Generates an interrupt request

SWIER7

Bit 7: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
1: Pend: Generates an interrupt request

SWIER8

Bit 8: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
1: Pend: Generates an interrupt request

SWIER9

Bit 9: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
1: Pend: Generates an interrupt request

SWIER10

Bit 10: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
1: Pend: Generates an interrupt request

SWIER11

Bit 11: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
1: Pend: Generates an interrupt request

SWIER12

Bit 12: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
1: Pend: Generates an interrupt request

SWIER13

Bit 13: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
1: Pend: Generates an interrupt request

SWIER14

Bit 14: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
1: Pend: Generates an interrupt request

SWIER15

Bit 15: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
1: Pend: Generates an interrupt request

SWIER16

Bit 16: Rising trigger event configuration bit of Configurable Event input.

Allowed values:
1: Pend: Generates an interrupt request

RPR1

EXTI rising edge pending register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

17/17 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															RPIF16 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RPIF15 rw	RPIF14 rw	RPIF13 rw	RPIF12 rw	RPIF11 rw	RPIF10 rw	RPIF9 rw	RPIF8 rw	RPIF7 rw	RPIF6 rw	RPIF5 rw	RPIF4 rw	RPIF3 rw	RPIF2 rw	RPIF1 rw	RPIF0 rw

Toggle fields

RPIF0

Bit 0: configurable event inputs x rising edge Pending bit..

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

RPIF1

Bit 1: configurable event inputs x rising edge Pending bit..

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

RPIF2

Bit 2: configurable event inputs x rising edge Pending bit..

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

RPIF3

Bit 3: configurable event inputs x rising edge Pending bit..

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

RPIF4

Bit 4: configurable event inputs x rising edge Pending bit..

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

RPIF5

Bit 5: configurable event inputs x rising edge Pending bit.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

RPIF6

Bit 6: configurable event inputs x rising edge Pending bit..

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

RPIF7

Bit 7: configurable event inputs x rising edge Pending bit..

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

RPIF8

Bit 8: configurable event inputs x rising edge Pending bit..

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

RPIF9

Bit 9: configurable event inputs x rising edge Pending bit..

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

RPIF10

Bit 10: configurable event inputs x rising edge Pending bit..

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

RPIF11

Bit 11: configurable event inputs x rising edge Pending bit..

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

RPIF12

Bit 12: configurable event inputs x rising edge Pending bit..

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

RPIF13

Bit 13: configurable event inputs x rising edge Pending bit..

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

RPIF14

Bit 14: configurable event inputs x rising edge Pending bit..

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

RPIF15

Bit 15: configurable event inputs x rising edge Pending bit..

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

RPIF16

Bit 16: configurable event inputs x rising edge Pending bit..

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

FPR1

EXTI falling edge pending register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

17/17 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															FPIF16 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FPIF15 rw	FPIF14 rw	FPIF13 rw	FPIF12 rw	FPIF11 rw	FPIF10 rw	FPIF9 rw	FPIF8 rw	FPIF7 rw	FPIF6 rw	FPIF5 rw	FPIF4 rw	FPIF3 rw	FPIF2 rw	FPIF1 rw	FPIF0 rw

Toggle fields

FPIF0

Bit 0: configurable event inputs x falling edge pending bit..

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

FPIF1

Bit 1: configurable event inputs x falling edge pending bit..

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

FPIF2

Bit 2: configurable event inputs x falling edge pending bit..

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

FPIF3

Bit 3: configurable event inputs x falling edge pending bit..

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

FPIF4

Bit 4: configurable event inputs x falling edge pending bit..

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

FPIF5

Bit 5: configurable event inputs x falling edge pending bit..

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

FPIF6

Bit 6: configurable event inputs x falling edge pending bit..

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

FPIF7

Bit 7: configurable event inputs x falling edge pending bit..

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

FPIF8

Bit 8: configurable event inputs x falling edge pending bit..

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

FPIF9

Bit 9: configurable event inputs x falling edge pending bit..

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

FPIF10

Bit 10: configurable event inputs x falling edge pending bit..

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

FPIF11

Bit 11: configurable event inputs x falling edge pending bit..

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

FPIF12

Bit 12: configurable event inputs x falling edge pending bit..

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

FPIF13

Bit 13: configurable event inputs x falling edge pending bit..

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

FPIF14

Bit 14: configurable event inputs x falling edge pending bit..

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

FPIF15

Bit 15: configurable event inputs x falling edge pending bit..

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

FPIF16

Bit 16: configurable event inputs x falling edge pending bit..

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

EXTICR1

EXTI external interrupt selection register

Offset: 0x60, size: 32, reset: 0x00000000, access: read-write

4/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
EXTI24_31 rw								EXTI16_23 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
EXTI8_15 rw								EXTI0_7 rw

Toggle fields

EXTI0_7

Bits 0-7: GPIO port selection.

Allowed values:
0: PA: GPIO port A selected
1: PB: GPIO port B selected
2: PC: GPIO port C selected
3: PD: GPIO port D selected
5: PF: GPIO port F selected

EXTI8_15

Bits 8-15: GPIO port selection.

Allowed values:
0: PA: GPIO port A selected
1: PB: GPIO port B selected
2: PC: GPIO port C selected
3: PD: GPIO port D selected
5: PF: GPIO port F selected

EXTI16_23

Bits 16-23: GPIO port selection.

Allowed values:
0: PA: GPIO port A selected
1: PB: GPIO port B selected
2: PC: GPIO port C selected
3: PD: GPIO port D selected
5: PF: GPIO port F selected

EXTI24_31

Bits 24-31: GPIO port selection.

Allowed values:
0: PA: GPIO port A selected
1: PB: GPIO port B selected
2: PC: GPIO port C selected
3: PD: GPIO port D selected
5: PF: GPIO port F selected

EXTICR2

EXTI external interrupt selection register

Offset: 0x64, size: 32, reset: 0x00000000, access: read-write

4/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
EXTI24_31 rw								EXTI16_23 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
EXTI8_15 rw								EXTI0_7 rw

Toggle fields

EXTI0_7

Bits 0-7: GPIO port selection.

Allowed values:
0: PA: GPIO port A selected
1: PB: GPIO port B selected
2: PC: GPIO port C selected
3: PD: GPIO port D selected
5: PF: GPIO port F selected

EXTI8_15

Bits 8-15: GPIO port selection.

Allowed values:
0: PA: GPIO port A selected
1: PB: GPIO port B selected
2: PC: GPIO port C selected
3: PD: GPIO port D selected
5: PF: GPIO port F selected

EXTI16_23

Bits 16-23: GPIO port selection.

Allowed values:
0: PA: GPIO port A selected
1: PB: GPIO port B selected
2: PC: GPIO port C selected
3: PD: GPIO port D selected
5: PF: GPIO port F selected

EXTI24_31

Bits 24-31: GPIO port selection.

Allowed values:
0: PA: GPIO port A selected
1: PB: GPIO port B selected
2: PC: GPIO port C selected
3: PD: GPIO port D selected
5: PF: GPIO port F selected

EXTICR3

EXTI external interrupt selection register

Offset: 0x68, size: 32, reset: 0x00000000, access: read-write

4/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
EXTI24_31 rw								EXTI16_23 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
EXTI8_15 rw								EXTI0_7 rw

Toggle fields

EXTI0_7

Bits 0-7: GPIO port selection.

Allowed values:
0: PA: GPIO port A selected
1: PB: GPIO port B selected
2: PC: GPIO port C selected
3: PD: GPIO port D selected
5: PF: GPIO port F selected

EXTI8_15

Bits 8-15: GPIO port selection.

Allowed values:
0: PA: GPIO port A selected
1: PB: GPIO port B selected
2: PC: GPIO port C selected
3: PD: GPIO port D selected
5: PF: GPIO port F selected

EXTI16_23

Bits 16-23: GPIO port selection.

Allowed values:
0: PA: GPIO port A selected
1: PB: GPIO port B selected
2: PC: GPIO port C selected
3: PD: GPIO port D selected
5: PF: GPIO port F selected

EXTI24_31

Bits 24-31: GPIO port selection.

Allowed values:
0: PA: GPIO port A selected
1: PB: GPIO port B selected
2: PC: GPIO port C selected
3: PD: GPIO port D selected
5: PF: GPIO port F selected

EXTICR4

EXTI external interrupt selection register

Offset: 0x6c, size: 32, reset: 0x00000000, access: read-write

4/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
EXTI24_31 rw								EXTI16_23 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
EXTI8_15 rw								EXTI0_7 rw

Toggle fields

EXTI0_7

Bits 0-7: GPIO port selection.

Allowed values:
0: PA: GPIO port A selected
1: PB: GPIO port B selected
2: PC: GPIO port C selected
3: PD: GPIO port D selected
5: PF: GPIO port F selected

EXTI8_15

Bits 8-15: GPIO port selection.

Allowed values:
0: PA: GPIO port A selected
1: PB: GPIO port B selected
2: PC: GPIO port C selected
3: PD: GPIO port D selected
5: PF: GPIO port F selected

EXTI16_23

Bits 16-23: GPIO port selection.

Allowed values:
0: PA: GPIO port A selected
1: PB: GPIO port B selected
2: PC: GPIO port C selected
3: PD: GPIO port D selected
5: PF: GPIO port F selected

EXTI24_31

Bits 24-31: GPIO port selection.

Allowed values:
0: PA: GPIO port A selected
1: PB: GPIO port B selected
2: PC: GPIO port C selected
3: PD: GPIO port D selected
5: PF: GPIO port F selected

IMR1

EXTI CPU wakeup with interrupt mask register

Offset: 0x80, size: 32, reset: 0xFFF80000, access: read-write

29/29 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
IM31 rw	IM30 rw	IM29 rw	IM28 rw		IM26 rw	IM25 rw	IM24 rw	IM23 rw	IM22 rw	IM21 rw	IM20 rw	IM19 rw			IM16 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IM15 rw	IM14 rw	IM13 rw	IM12 rw	IM11 rw	IM10 rw	IM9 rw	IM8 rw	IM7 rw	IM6 rw	IM5 rw	IM4 rw	IM3 rw	IM2 rw	IM1 rw	IM0 rw

Toggle fields

IM0

Bit 0: CPU wakeup with interrupt mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

IM1

Bit 1: CPU wakeup with interrupt mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

IM2

Bit 2: CPU wakeup with interrupt mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

IM3

Bit 3: CPU wakeup with interrupt mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

IM4

Bit 4: CPU wakeup with interrupt mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

IM5

Bit 5: CPU wakeup with interrupt mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

IM6

Bit 6: CPU wakeup with interrupt mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

IM7

Bit 7: CPU wakeup with interrupt mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

IM8

Bit 8: CPU wakeup with interrupt mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

IM9

Bit 9: CPU wakeup with interrupt mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

IM10

Bit 10: CPU wakeup with interrupt mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

IM11

Bit 11: CPU wakeup with interrupt mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

IM12

Bit 12: CPU wakeup with interrupt mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

IM13

Bit 13: CPU wakeup with interrupt mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

IM14

Bit 14: CPU wakeup with interrupt mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

IM15

Bit 15: CPU wakeup with interrupt mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

IM16

Bit 16: CPU wakeup with interrupt mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

IM19

Bit 19: CPU wakeup with interrupt mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

IM20

Bit 20: CPU wakeup with interrupt mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

IM21

Bit 21: CPU wakeup with interrupt mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

IM22

Bit 22: CPU wakeup with interrupt mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

IM23

Bit 23: CPU wakeup with interrupt mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

IM24

Bit 24: CPU wakeup with interrupt mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

IM25

Bit 25: CPU wakeup with interrupt mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

IM26

Bit 26: CPU wakeup with interrupt mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

IM28

Bit 28: CPU wakeup with interrupt mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

IM29

Bit 29: CPU wakeup with interrupt mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

IM30

Bit 30: CPU wakeup with interrupt mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

IM31

Bit 31: CPU wakeup with interrupt mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

EMR1

EXTI CPU wakeup with event mask register

Offset: 0x84, size: 32, reset: 0x00000000, access: read-write

26/26 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
EM31 rw	EM30 rw	EM29 rw	EM28 rw		EM26 rw	EM25 rw		EM23 rw		EM21 rw		EM19 rw			EM16 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
EM15 rw	EM14 rw	EM13 rw	EM12 rw	EM11 rw	EM10 rw	EM9 rw	EM8 rw	EM7 rw	EM6 rw	EM5 rw	EM4 rw	EM3 rw	EM2 rw	EM1 rw	EM0 rw

Toggle fields

EM0

Bit 0: CPU wakeup with event mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

EM1

Bit 1: CPU wakeup with event mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

EM2

Bit 2: CPU wakeup with event mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

EM3

Bit 3: CPU wakeup with event mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

EM4

Bit 4: CPU wakeup with event mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

EM5

Bit 5: CPU wakeup with event mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

EM6

Bit 6: CPU wakeup with event mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

EM7

Bit 7: CPU wakeup with event mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

EM8

Bit 8: CPU wakeup with event mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

EM9

Bit 9: CPU wakeup with event mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

EM10

Bit 10: CPU wakeup with event mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

EM11

Bit 11: CPU wakeup with event mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

EM12

Bit 12: CPU wakeup with event mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

EM13

Bit 13: CPU wakeup with event mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

EM14

Bit 14: CPU wakeup with event mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

EM15

Bit 15: CPU wakeup with event mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

EM16

Bit 16: CPU wakeup with event mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

EM19

Bit 19: CPU wakeup with event mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

EM21

Bit 21: CPU wakeup with event mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

EM23

Bit 23: CPU wakeup with event mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

EM25

Bit 25: CPU wakeup with event mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

EM26

Bit 26: CPU wakeup with event mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

EM28

Bit 28: CPU wakeup with event mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

EM29

Bit 29: CPU wakeup with event mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

EM30

Bit 30: CPU wakeup with event mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

EM31

Bit 31: CPU wakeup with event mask on event input.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

FLASH

0x40022000: Flash

11/73 fields covered.

Toggle register map

Offset	Name	31	30	29	28	27	26	25	24	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	ACR													DBG_SWEN		EMPTY					ICRST		ICEN	PRFTEN						LATENCY
0x8	KEYR	KEY															KEY
0xc	OPTKEYR	OPTKEY															OPTKEY
0x10	SR													CFGBSY		BSY	OPTVERR	RDERR					FASTERR	MISSERR	PGSERR	SIZERR	PGAERR	WRPERR	PROGERR		OPERR	EOP
0x14	CR	LOCK	OPTLOCK		SEC_PROT	OBL_LAUNCH	RDERRIE	ERRIE	EOPIE					FSTPG	OPTSTRT	STRT								PNB						MER	PER	PG
0x18	ECCR	ECCD	ECCC						ECCIE			SYSF_ECC						ADDR_ECC
0x1c	ECCR2	ECCD	ECCC						ECCIE			SYSF_ECC						ADDR_ECC
0x20	OPTR			IRHEN	NRST_MODE		nBOOT0	nBOOT1	nBOOT_SEL	RAM_PARITY_CHECK			WWDG_SW	IWDG_STDBY	IWDG_STOP	IWDG_SW	nRSTS_HDW	nRST_STDBY	nRST_STOP	BORR_LEV		BORF_LEV		BOREN	RDP
0x24	PCROP1ASR																								PCROP1A_STRT
0x28	PCROP1AER	PCROP_RDP																							PCROP1A_END
0x2c	WRP1AR										WRP1A_END																WRP1A_STRT
0x30	WRP1BR										WRP1B_END																WRP1B_STRT
0x34	PCROP1BSR																								PCROP1B_STRT
0x38	PCROP1BER																								PCROP1B_END
0x80	SECR															BOOT_LOCK										SEC_SIZE

Toggle registers

ACR

Access control register

Offset: 0x0, size: 32, reset: 0x00000600, access: read-write

0/6 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
													DBG_SWEN rw		EMPTY rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				ICRST rw		ICEN rw	PRFTEN rw						LATENCY rw

Toggle fields

LATENCY

Bits 0-2: Latency.

PRFTEN

Bit 8: Prefetch enable.

ICEN

Bit 9: Instruction cache enable.

ICRST

Bit 11: Instruction cache reset.

EMPTY

Bit 16: Flash User area empty.

DBG_SWEN

Bit 18: Debug access software enable.

KEYR

Flash key register

Offset: 0x8, size: 32, reset: 0x00000000, access: write-only

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
KEY w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
KEY w

Toggle fields

KEY

Bits 0-31: KEYR.

OPTKEYR

Option byte key register

Offset: 0xc, size: 32, reset: 0x00000000, access: write-only

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OPTKEY w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OPTKEY w

Toggle fields

OPTKEY

Bits 0-31: Option byte key.

SR

Status register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

0/13 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
													CFGBSY rw		BSY rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OPTVERR rw	RDERR rw					FASTERR rw	MISSERR rw	PGSERR rw	SIZERR rw	PGAERR rw	WRPERR rw	PROGERR rw		OPERR rw	EOP rw

Toggle fields

EOP

Bit 0: End of operation.

OPERR

Bit 1: Operation error.

PROGERR

Bit 3: Programming error.

WRPERR

Bit 4: Write protected error.

PGAERR

Bit 5: Programming alignment error.

SIZERR

Bit 6: Size error.

PGSERR

Bit 7: Programming sequence error.

MISSERR

Bit 8: Fast programming data miss error.

FASTERR

Bit 9: Fast programming error.

RDERR

Bit 14: PCROP read error.

OPTVERR

Bit 15: Option and Engineering bits loading validity error.

BSY

Bit 16: Busy.

CFGBSY

Bit 18: Programming or erase configuration busy..

CR

Flash control register

Offset: 0x14, size: 32, reset: 0xC0000000, access: read-write

0/14 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
LOCK rw	OPTLOCK rw		SEC_PROT rw	OBL_LAUNCH rw	RDERRIE rw	ERRIE rw	EOPIE rw						FSTPG rw	OPTSTRT rw	STRT rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							PNB rw						MER rw	PER rw	PG rw

Toggle fields

PG

Bit 0: Programming.

PER

Bit 1: Page erase.

MER

Bit 2: Mass erase.

PNB

Bits 3-8: Page number.

STRT

Bit 16: Start.

OPTSTRT

Bit 17: Options modification start.

FSTPG

Bit 18: Fast programming.

EOPIE

Bit 24: End of operation interrupt enable.

ERRIE

Bit 25: Error interrupt enable.

RDERRIE

Bit 26: PCROP read error interrupt enable.

OBL_LAUNCH

Bit 27: Force the option byte loading.

SEC_PROT

Bit 28: Securable memory area protection enable.

OPTLOCK

Bit 30: Options Lock.

LOCK

Bit 31: FLASH_CR Lock.

ECCR

Flash ECC register

Offset: 0x18, size: 32, reset: 0x00000000, access: Unspecified

2/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ECCD rw	ECCC rw						ECCIE rw				SYSF_ECC r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	ADDR_ECC r

Toggle fields

ADDR_ECC

Bits 0-14: ECC fail address.

SYSF_ECC

Bit 20: ECC fail for Corrected ECC Error or Double ECC Error in info block.

ECCIE

Bit 24: ECC correction interrupt enable.

ECCC

Bit 30: ECC correction.

ECCD

Bit 31: ECC detection.

ECCR2

Flash ECC register 2

Offset: 0x1c, size: 32, reset: 0x00000000, access: Unspecified

2/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ECCD rw	ECCC rw						ECCIE rw				SYSF_ECC r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	ADDR_ECC r

Toggle fields

ADDR_ECC

Bits 0-14: ECC fail address.

SYSF_ECC

Bit 20: ECC fail for Corrected ECC Error or Double ECC Error in info block.

ECCIE

Bit 24: ECC correction interrupt enable.

ECCC

Bit 30: ECC correction.

ECCD

Bit 31: ECC detection.

OPTR

Flash option register

Offset: 0x20, size: 32, reset: 0xF0000000, access: read-write

0/17 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
		IRHEN rw	NRST_MODE rw		nBOOT0 rw	nBOOT1 rw	nBOOT_SEL rw		RAM_PARITY_CHECK rw			WWDG_SW rw	IWDG_STDBY rw	IWDG_STOP rw	IWDG_SW rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
nRSTS_HDW rw	nRST_STDBY rw	nRST_STOP rw	BORR_LEV rw		BORF_LEV rw		BOREN rw	RDP rw

Toggle fields

RDP

Bits 0-7: Read protection level.

BOREN

Bit 8: BOR reset Level.

BORF_LEV

Bits 9-10: These bits contain the VDD supply level threshold that activates the reset.

BORR_LEV

Bits 11-12: These bits contain the VDD supply level threshold that releases the reset..

nRST_STOP

Bit 13: nRST_STOP.

nRST_STDBY

Bit 14: nRST_STDBY.

nRSTS_HDW

Bit 15: nRSTS_HDW.

IWDG_SW

Bit 16: Independent watchdog selection.

IWDG_STOP

Bit 17: Independent watchdog counter freeze in Stop mode.

IWDG_STDBY

Bit 18: Independent watchdog counter freeze in Standby mode.

WWDG_SW

Bit 19: Window watchdog selection.

RAM_PARITY_CHECK

Bit 22: SRAM parity check control.

nBOOT_SEL

Bit 24: nBOOT_SEL.

nBOOT1

Bit 25: Boot configuration.

nBOOT0

Bit 26: nBOOT0 option bit.

NRST_MODE

Bits 27-28: NRST_MODE.

IRHEN

Bit 29: Internal reset holder enable bit.

PCROP1ASR

Flash PCROP zone A Start address register

Offset: 0x24, size: 32, reset: 0xF0000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								PCROP1A_STRT r

Toggle fields

PCROP1A_STRT

Bits 0-7: PCROP1A area start offset.

PCROP1AER

Flash PCROP zone A End address register

Offset: 0x28, size: 32, reset: 0xF0000000, access: read-only

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PCROP_RDP r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								PCROP1A_END r

Toggle fields

PCROP1A_END

Bits 0-7: PCROP1A area end offset.

PCROP_RDP

Bit 31: PCROP area preserved when RDP level decreased.

WRP1AR

Flash WRP area A address register

Offset: 0x2c, size: 32, reset: 0x000000FF, access: read-write

0/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
										WRP1A_END rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
										WRP1A_STRT rw

Toggle fields

WRP1A_STRT

Bits 0-5: WRP area A start offset.

WRP1A_END

Bits 16-21: WRP area A end offset.

WRP1BR

Flash WRP area B address register

Offset: 0x30, size: 32, reset: 0x000000FF, access: read-write

0/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
										WRP1B_END rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
										WRP1B_STRT rw

Toggle fields

WRP1B_STRT

Bits 0-5: WRP area B start offset.

WRP1B_END

Bits 16-21: WRP area B end offset.

PCROP1BSR

Flash PCROP zone B Start address register

Offset: 0x34, size: 32, reset: 0xF0000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								PCROP1B_STRT r

Toggle fields

PCROP1B_STRT

Bits 0-7: PCROP1B area start offset.

PCROP1BER

Flash PCROP zone B End address register

Offset: 0x38, size: 32, reset: 0xF0000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								PCROP1B_END r

Toggle fields

PCROP1B_END

Bits 0-7: PCROP1B area end offset.

SECR

Flash Security register

Offset: 0x80, size: 32, reset: 0xF0000000, access: read-only

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															BOOT_LOCK r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
									SEC_SIZE r

Toggle fields

SEC_SIZE

Bits 0-6: Securable memory area size.

BOOT_LOCK

Bit 16: used to force boot from user area.

GPIOA

0x50000000: General-purpose I/Os

177/177 fields covered.

Toggle register map

Offset	Name	31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	MODER	MODER[15]		MODER[14]		MODER[13]		MODER[12]		MODER[11]		MODER[10]		MODER[9]		MODER[8]		MODER[7]		MODER[6]		MODER[5]		MODER[4]		MODER[3]		MODER[2]		MODER[1]		MODER[0]
0x4	OTYPER																	OT[15]	OT[14]	OT[13]	OT[12]	OT[11]	OT[10]	OT[9]	OT[8]	OT[7]	OT[6]	OT[5]	OT[4]	OT[3]	OT[2]	OT[1]	OT[0]
0x8	OSPEEDR	OSPEEDR[15]		OSPEEDR[14]		OSPEEDR[13]		OSPEEDR[12]		OSPEEDR[11]		OSPEEDR[10]		OSPEEDR[9]		OSPEEDR[8]		OSPEEDR[7]		OSPEEDR[6]		OSPEEDR[5]		OSPEEDR[4]		OSPEEDR[3]		OSPEEDR[2]		OSPEEDR[1]		OSPEEDR[0]
0xc	PUPDR	PUPDR[15]		PUPDR[14]		PUPDR[13]		PUPDR[12]		PUPDR[11]		PUPDR[10]		PUPDR[9]		PUPDR[8]		PUPDR[7]		PUPDR[6]		PUPDR[5]		PUPDR[4]		PUPDR[3]		PUPDR[2]		PUPDR[1]		PUPDR[0]
0x10	IDR																	IDR[15]	IDR[14]	IDR[13]	IDR[12]	IDR[11]	IDR[10]	IDR[9]	IDR[8]	IDR[7]	IDR[6]	IDR[5]	IDR[4]	IDR[3]	IDR[2]	IDR[1]	IDR[0]
0x14	ODR																	ODR[15]	ODR[14]	ODR[13]	ODR[12]	ODR[11]	ODR[10]	ODR[9]	ODR[8]	ODR[7]	ODR[6]	ODR[5]	ODR[4]	ODR[3]	ODR[2]	ODR[1]	ODR[0]
0x18	BSRR	BR[15]	BR[14]	BR[13]	BR[12]	BR[11]	BR[10]	BR[9]	BR[8]	BR[7]	BR[6]	BR[5]	BR[4]	BR[3]	BR[2]	BR[1]	BR[0]	BS[15]	BS[14]	BS[13]	BS[12]	BS[11]	BS[10]	BS[9]	BS[8]	BS[7]	BS[6]	BS[5]	BS[4]	BS[3]	BS[2]	BS[1]	BS[0]
0x1c	LCKR																LCKK	LCK[15]	LCK[14]	LCK[13]	LCK[12]	LCK[11]	LCK[10]	LCK[9]	LCK[8]	LCK[7]	LCK[6]	LCK[5]	LCK[4]	LCK[3]	LCK[2]	LCK[1]	LCK[0]
0x20	AFRL	AFR[EL7]				AFR[EL6]				AFR[EL5]				AFR[EL4]				AFR[EL3]				AFR[EL2]				AFR[EL1]				AFR[EL0]
0x24	AFRH	AFR[EL15]				AFR[EL14]				AFR[EL13]				AFR[EL12]				AFR[EL11]				AFR[EL10]				AFR[EL9]				AFR[EL8]
0x28	BRR																	BR[15]	BR[14]	BR[13]	BR[12]	BR[11]	BR[10]	BR[9]	BR[8]	BR[7]	BR[6]	BR[5]	BR[4]	BR[3]	BR[2]	BR[1]	BR[0]

Toggle registers

MODER

GPIO port mode register

Offset: 0x0, size: 32, reset: 0xEBFFFFFF, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MODER[15] rw		MODER[14] rw		MODER[13] rw		MODER[12] rw		MODER[11] rw		MODER[10] rw		MODER[9] rw		MODER[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MODER[7] rw		MODER[6] rw		MODER[5] rw		MODER[4] rw		MODER[3] rw		MODER[2] rw		MODER[1] rw		MODER[0] rw

Toggle fields

MODER[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

OTYPER

GPIO port output type register

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OT[15] rw	OT[14] rw	OT[13] rw	OT[12] rw	OT[11] rw	OT[10] rw	OT[9] rw	OT[8] rw	OT[7] rw	OT[6] rw	OT[5] rw	OT[4] rw	OT[3] rw	OT[2] rw	OT[1] rw	OT[0] rw

Toggle fields

OT[0]

Bit 0: Port x configuration pin 0.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[1]

Bit 1: Port x configuration pin 1.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[2]

Bit 2: Port x configuration pin 2.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[3]

Bit 3: Port x configuration pin 3.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[4]

Bit 4: Port x configuration pin 4.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[5]

Bit 5: Port x configuration pin 5.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[6]

Bit 6: Port x configuration pin 6.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[7]

Bit 7: Port x configuration pin 7.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[8]

Bit 8: Port x configuration pin 8.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[9]

Bit 9: Port x configuration pin 9.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[10]

Bit 10: Port x configuration pin 10.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[11]

Bit 11: Port x configuration pin 11.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[12]

Bit 12: Port x configuration pin 12.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[13]

Bit 13: Port x configuration pin 13.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[14]

Bit 14: Port x configuration pin 14.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[15]

Bit 15: Port x configuration pin 15.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OSPEEDR

GPIO port output speed register

Offset: 0x8, size: 32, reset: 0x0C000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OSPEEDR[15] rw		OSPEEDR[14] rw		OSPEEDR[13] rw		OSPEEDR[12] rw		OSPEEDR[11] rw		OSPEEDR[10] rw		OSPEEDR[9] rw		OSPEEDR[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OSPEEDR[7] rw		OSPEEDR[6] rw		OSPEEDR[5] rw		OSPEEDR[4] rw		OSPEEDR[3] rw		OSPEEDR[2] rw		OSPEEDR[1] rw		OSPEEDR[0] rw

Toggle fields

OSPEEDR[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

PUPDR

GPIO port pull-up/pull-down register

Offset: 0xc, size: 32, reset: 0x24000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PUPDR[15] rw		PUPDR[14] rw		PUPDR[13] rw		PUPDR[12] rw		PUPDR[11] rw		PUPDR[10] rw		PUPDR[9] rw		PUPDR[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PUPDR[7] rw		PUPDR[6] rw		PUPDR[5] rw		PUPDR[4] rw		PUPDR[3] rw		PUPDR[2] rw		PUPDR[1] rw		PUPDR[0] rw

Toggle fields

PUPDR[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

IDR

GPIO port input data register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-only

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IDR[15] r	IDR[14] r	IDR[13] r	IDR[12] r	IDR[11] r	IDR[10] r	IDR[9] r	IDR[8] r	IDR[7] r	IDR[6] r	IDR[5] r	IDR[4] r	IDR[3] r	IDR[2] r	IDR[1] r	IDR[0] r

Toggle fields

IDR[0]

Bit 0: Port input data pin 0.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[1]

Bit 1: Port input data pin 1.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[2]

Bit 2: Port input data pin 2.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[3]

Bit 3: Port input data pin 3.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[4]

Bit 4: Port input data pin 4.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[5]

Bit 5: Port input data pin 5.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[6]

Bit 6: Port input data pin 6.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[7]

Bit 7: Port input data pin 7.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[8]

Bit 8: Port input data pin 8.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[9]

Bit 9: Port input data pin 9.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[10]

Bit 10: Port input data pin 10.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[11]

Bit 11: Port input data pin 11.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[12]

Bit 12: Port input data pin 12.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[13]

Bit 13: Port input data pin 13.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[14]

Bit 14: Port input data pin 14.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[15]

Bit 15: Port input data pin 15.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

ODR

GPIO port output data register

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ODR[15] rw	ODR[14] rw	ODR[13] rw	ODR[12] rw	ODR[11] rw	ODR[10] rw	ODR[9] rw	ODR[8] rw	ODR[7] rw	ODR[6] rw	ODR[5] rw	ODR[4] rw	ODR[3] rw	ODR[2] rw	ODR[1] rw	ODR[0] rw

Toggle fields

ODR[0]

Bit 0: Port output data pin 0.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[1]

Bit 1: Port output data pin 1.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[2]

Bit 2: Port output data pin 2.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[3]

Bit 3: Port output data pin 3.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[4]

Bit 4: Port output data pin 4.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[5]

Bit 5: Port output data pin 5.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[6]

Bit 6: Port output data pin 6.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[7]

Bit 7: Port output data pin 7.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[8]

Bit 8: Port output data pin 8.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[9]

Bit 9: Port output data pin 9.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[10]

Bit 10: Port output data pin 10.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[11]

Bit 11: Port output data pin 11.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[12]

Bit 12: Port output data pin 12.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[13]

Bit 13: Port output data pin 13.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[14]

Bit 14: Port output data pin 14.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[15]

Bit 15: Port output data pin 15.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

BSRR

GPIO port bit set/reset register

Offset: 0x18, size: 32, reset: 0x00000000, access: write-only

32/32 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BR[15] w	BR[14] w	BR[13] w	BR[12] w	BR[11] w	BR[10] w	BR[9] w	BR[8] w	BR[7] w	BR[6] w	BR[5] w	BR[4] w	BR[3] w	BR[2] w	BR[1] w	BR[0] w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BS[15] w	BS[14] w	BS[13] w	BS[12] w	BS[11] w	BS[10] w	BS[9] w	BS[8] w	BS[7] w	BS[6] w	BS[5] w	BS[4] w	BS[3] w	BS[2] w	BS[1] w	BS[0] w

Toggle fields

BS[0]

Bit 0: Port x set pin 0.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[1]

Bit 1: Port x set pin 1.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[2]

Bit 2: Port x set pin 2.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[3]

Bit 3: Port x set pin 3.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[4]

Bit 4: Port x set pin 4.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[5]

Bit 5: Port x set pin 5.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[6]

Bit 6: Port x set pin 6.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[7]

Bit 7: Port x set pin 7.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[8]

Bit 8: Port x set pin 8.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[9]

Bit 9: Port x set pin 9.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[10]

Bit 10: Port x set pin 10.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[11]

Bit 11: Port x set pin 11.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[12]

Bit 12: Port x set pin 12.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[13]

Bit 13: Port x set pin 13.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[14]

Bit 14: Port x set pin 14.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[15]

Bit 15: Port x set pin 15.

Allowed values:
1: Set: Sets the corresponding ODx bit

BR[0]

Bit 16: Port x reset pin 0.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[1]

Bit 17: Port x reset pin 1.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[2]

Bit 18: Port x reset pin 2.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[3]

Bit 19: Port x reset pin 3.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[4]

Bit 20: Port x reset pin 4.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[5]

Bit 21: Port x reset pin 5.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[6]

Bit 22: Port x reset pin 6.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[7]

Bit 23: Port x reset pin 7.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[8]

Bit 24: Port x reset pin 8.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[9]

Bit 25: Port x reset pin 9.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[10]

Bit 26: Port x reset pin 10.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[11]

Bit 27: Port x reset pin 11.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[12]

Bit 28: Port x reset pin 12.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[13]

Bit 29: Port x reset pin 13.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[14]

Bit 30: Port x reset pin 14.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[15]

Bit 31: Port x reset pin 15.

Allowed values:
1: Reset: Resets the corresponding ODx bit

LCKR

GPIO port configuration lock register

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

17/17 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															LCKK rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
LCK[15] rw	LCK[14] rw	LCK[13] rw	LCK[12] rw	LCK[11] rw	LCK[10] rw	LCK[9] rw	LCK[8] rw	LCK[7] rw	LCK[6] rw	LCK[5] rw	LCK[4] rw	LCK[3] rw	LCK[2] rw	LCK[1] rw	LCK[0] rw

Toggle fields

LCK[0]

Bit 0: Port x lock pin 0.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[1]

Bit 1: Port x lock pin 1.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[2]

Bit 2: Port x lock pin 2.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[3]

Bit 3: Port x lock pin 3.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[4]

Bit 4: Port x lock pin 4.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[5]

Bit 5: Port x lock pin 5.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[6]

Bit 6: Port x lock pin 6.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[7]

Bit 7: Port x lock pin 7.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[8]

Bit 8: Port x lock pin 8.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[9]

Bit 9: Port x lock pin 9.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[10]

Bit 10: Port x lock pin 10.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[11]

Bit 11: Port x lock pin 11.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[12]

Bit 12: Port x lock pin 12.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[13]

Bit 13: Port x lock pin 13.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[14]

Bit 14: Port x lock pin 14.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[15]

Bit 15: Port x lock pin 15.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCKK

Bit 16: Port x lock bit y (y= 0..15).

Allowed values:
0: NotActive: Port configuration lock key not active
1: Active: Port configuration lock key active

AFRL

GPIO alternate function low register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AFR[EL7] rw				AFR[EL6] rw				AFR[EL5] rw				AFR[EL4] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AFR[EL3] rw				AFR[EL2] rw				AFR[EL1] rw				AFR[EL0] rw

Toggle fields

AFR[EL0]

Bits 0-3: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL1]

Bits 4-7: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL2]

Bits 8-11: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL3]

Bits 12-15: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL4]

Bits 16-19: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL5]

Bits 20-23: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL6]

Bits 24-27: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL7]

Bits 28-31: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFRH

GPIO alternate function high register

Offset: 0x24, size: 32, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AFR[EL15] rw				AFR[EL14] rw				AFR[EL13] rw				AFR[EL12] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AFR[EL11] rw				AFR[EL10] rw				AFR[EL9] rw				AFR[EL8] rw

Toggle fields

AFR[EL8]

Bits 0-3: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL9]

Bits 4-7: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL10]

Bits 8-11: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL11]

Bits 12-15: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL12]

Bits 16-19: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL13]

Bits 20-23: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL14]

Bits 24-27: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL15]

Bits 28-31: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

BRR

port bit reset register

Offset: 0x28, size: 32, reset: 0x00000000, access: write-only

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BR[15] w	BR[14] w	BR[13] w	BR[12] w	BR[11] w	BR[10] w	BR[9] w	BR[8] w	BR[7] w	BR[6] w	BR[5] w	BR[4] w	BR[3] w	BR[2] w	BR[1] w	BR[0] w

Toggle fields

BR[0]

Bit 0: Port x reset pin 0.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[1]

Bit 1: Port x reset pin 1.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[2]

Bit 2: Port x reset pin 2.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[3]

Bit 3: Port x reset pin 3.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[4]

Bit 4: Port x reset pin 4.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[5]

Bit 5: Port x reset pin 5.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[6]

Bit 6: Port x reset pin 6.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[7]

Bit 7: Port x reset pin 7.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[8]

Bit 8: Port x reset pin 8.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[9]

Bit 9: Port x reset pin 9.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[10]

Bit 10: Port x reset pin 10.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[11]

Bit 11: Port x reset pin 11.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[12]

Bit 12: Port x reset pin 12.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[13]

Bit 13: Port x reset pin 13.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[14]

Bit 14: Port x reset pin 14.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[15]

Bit 15: Port x reset pin 15.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

GPIOB

0x50000400: General-purpose I/Os

177/177 fields covered.

Toggle register map

Offset	Name	31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	MODER	MODER[15]		MODER[14]		MODER[13]		MODER[12]		MODER[11]		MODER[10]		MODER[9]		MODER[8]		MODER[7]		MODER[6]		MODER[5]		MODER[4]		MODER[3]		MODER[2]		MODER[1]		MODER[0]
0x4	OTYPER																	OT[15]	OT[14]	OT[13]	OT[12]	OT[11]	OT[10]	OT[9]	OT[8]	OT[7]	OT[6]	OT[5]	OT[4]	OT[3]	OT[2]	OT[1]	OT[0]
0x8	OSPEEDR	OSPEEDR[15]		OSPEEDR[14]		OSPEEDR[13]		OSPEEDR[12]		OSPEEDR[11]		OSPEEDR[10]		OSPEEDR[9]		OSPEEDR[8]		OSPEEDR[7]		OSPEEDR[6]		OSPEEDR[5]		OSPEEDR[4]		OSPEEDR[3]		OSPEEDR[2]		OSPEEDR[1]		OSPEEDR[0]
0xc	PUPDR	PUPDR[15]		PUPDR[14]		PUPDR[13]		PUPDR[12]		PUPDR[11]		PUPDR[10]		PUPDR[9]		PUPDR[8]		PUPDR[7]		PUPDR[6]		PUPDR[5]		PUPDR[4]		PUPDR[3]		PUPDR[2]		PUPDR[1]		PUPDR[0]
0x10	IDR																	IDR[15]	IDR[14]	IDR[13]	IDR[12]	IDR[11]	IDR[10]	IDR[9]	IDR[8]	IDR[7]	IDR[6]	IDR[5]	IDR[4]	IDR[3]	IDR[2]	IDR[1]	IDR[0]
0x14	ODR																	ODR[15]	ODR[14]	ODR[13]	ODR[12]	ODR[11]	ODR[10]	ODR[9]	ODR[8]	ODR[7]	ODR[6]	ODR[5]	ODR[4]	ODR[3]	ODR[2]	ODR[1]	ODR[0]
0x18	BSRR	BR[15]	BR[14]	BR[13]	BR[12]	BR[11]	BR[10]	BR[9]	BR[8]	BR[7]	BR[6]	BR[5]	BR[4]	BR[3]	BR[2]	BR[1]	BR[0]	BS[15]	BS[14]	BS[13]	BS[12]	BS[11]	BS[10]	BS[9]	BS[8]	BS[7]	BS[6]	BS[5]	BS[4]	BS[3]	BS[2]	BS[1]	BS[0]
0x1c	LCKR																LCKK	LCK[15]	LCK[14]	LCK[13]	LCK[12]	LCK[11]	LCK[10]	LCK[9]	LCK[8]	LCK[7]	LCK[6]	LCK[5]	LCK[4]	LCK[3]	LCK[2]	LCK[1]	LCK[0]
0x20	AFRL	AFR[EL7]				AFR[EL6]				AFR[EL5]				AFR[EL4]				AFR[EL3]				AFR[EL2]				AFR[EL1]				AFR[EL0]
0x24	AFRH	AFR[EL15]				AFR[EL14]				AFR[EL13]				AFR[EL12]				AFR[EL11]				AFR[EL10]				AFR[EL9]				AFR[EL8]
0x28	BRR																	BR[15]	BR[14]	BR[13]	BR[12]	BR[11]	BR[10]	BR[9]	BR[8]	BR[7]	BR[6]	BR[5]	BR[4]	BR[3]	BR[2]	BR[1]	BR[0]

Toggle registers

MODER

GPIO port mode register

Offset: 0x0, size: 32, reset: 0xFFFFFFFF, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MODER[15] rw		MODER[14] rw		MODER[13] rw		MODER[12] rw		MODER[11] rw		MODER[10] rw		MODER[9] rw		MODER[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MODER[7] rw		MODER[6] rw		MODER[5] rw		MODER[4] rw		MODER[3] rw		MODER[2] rw		MODER[1] rw		MODER[0] rw

Toggle fields

MODER[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

OTYPER

GPIO port output type register

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OT[15] rw	OT[14] rw	OT[13] rw	OT[12] rw	OT[11] rw	OT[10] rw	OT[9] rw	OT[8] rw	OT[7] rw	OT[6] rw	OT[5] rw	OT[4] rw	OT[3] rw	OT[2] rw	OT[1] rw	OT[0] rw

Toggle fields

OT[0]

Bit 0: Port x configuration pin 0.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[1]

Bit 1: Port x configuration pin 1.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[2]

Bit 2: Port x configuration pin 2.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[3]

Bit 3: Port x configuration pin 3.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[4]

Bit 4: Port x configuration pin 4.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[5]

Bit 5: Port x configuration pin 5.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[6]

Bit 6: Port x configuration pin 6.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[7]

Bit 7: Port x configuration pin 7.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[8]

Bit 8: Port x configuration pin 8.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[9]

Bit 9: Port x configuration pin 9.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[10]

Bit 10: Port x configuration pin 10.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[11]

Bit 11: Port x configuration pin 11.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[12]

Bit 12: Port x configuration pin 12.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[13]

Bit 13: Port x configuration pin 13.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[14]

Bit 14: Port x configuration pin 14.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[15]

Bit 15: Port x configuration pin 15.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OSPEEDR

GPIO port output speed register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OSPEEDR[15] rw		OSPEEDR[14] rw		OSPEEDR[13] rw		OSPEEDR[12] rw		OSPEEDR[11] rw		OSPEEDR[10] rw		OSPEEDR[9] rw		OSPEEDR[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OSPEEDR[7] rw		OSPEEDR[6] rw		OSPEEDR[5] rw		OSPEEDR[4] rw		OSPEEDR[3] rw		OSPEEDR[2] rw		OSPEEDR[1] rw		OSPEEDR[0] rw

Toggle fields

OSPEEDR[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

PUPDR

GPIO port pull-up/pull-down register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PUPDR[15] rw		PUPDR[14] rw		PUPDR[13] rw		PUPDR[12] rw		PUPDR[11] rw		PUPDR[10] rw		PUPDR[9] rw		PUPDR[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PUPDR[7] rw		PUPDR[6] rw		PUPDR[5] rw		PUPDR[4] rw		PUPDR[3] rw		PUPDR[2] rw		PUPDR[1] rw		PUPDR[0] rw

Toggle fields

PUPDR[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

IDR

GPIO port input data register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-only

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IDR[15] r	IDR[14] r	IDR[13] r	IDR[12] r	IDR[11] r	IDR[10] r	IDR[9] r	IDR[8] r	IDR[7] r	IDR[6] r	IDR[5] r	IDR[4] r	IDR[3] r	IDR[2] r	IDR[1] r	IDR[0] r

Toggle fields

IDR[0]

Bit 0: Port input data pin 0.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[1]

Bit 1: Port input data pin 1.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[2]

Bit 2: Port input data pin 2.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[3]

Bit 3: Port input data pin 3.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[4]

Bit 4: Port input data pin 4.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[5]

Bit 5: Port input data pin 5.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[6]

Bit 6: Port input data pin 6.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[7]

Bit 7: Port input data pin 7.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[8]

Bit 8: Port input data pin 8.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[9]

Bit 9: Port input data pin 9.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[10]

Bit 10: Port input data pin 10.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[11]

Bit 11: Port input data pin 11.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[12]

Bit 12: Port input data pin 12.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[13]

Bit 13: Port input data pin 13.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[14]

Bit 14: Port input data pin 14.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[15]

Bit 15: Port input data pin 15.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

ODR

GPIO port output data register

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ODR[15] rw	ODR[14] rw	ODR[13] rw	ODR[12] rw	ODR[11] rw	ODR[10] rw	ODR[9] rw	ODR[8] rw	ODR[7] rw	ODR[6] rw	ODR[5] rw	ODR[4] rw	ODR[3] rw	ODR[2] rw	ODR[1] rw	ODR[0] rw

Toggle fields

ODR[0]

Bit 0: Port output data pin 0.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[1]

Bit 1: Port output data pin 1.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[2]

Bit 2: Port output data pin 2.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[3]

Bit 3: Port output data pin 3.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[4]

Bit 4: Port output data pin 4.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[5]

Bit 5: Port output data pin 5.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[6]

Bit 6: Port output data pin 6.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[7]

Bit 7: Port output data pin 7.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[8]

Bit 8: Port output data pin 8.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[9]

Bit 9: Port output data pin 9.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[10]

Bit 10: Port output data pin 10.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[11]

Bit 11: Port output data pin 11.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[12]

Bit 12: Port output data pin 12.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[13]

Bit 13: Port output data pin 13.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[14]

Bit 14: Port output data pin 14.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[15]

Bit 15: Port output data pin 15.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

BSRR

GPIO port bit set/reset register

Offset: 0x18, size: 32, reset: 0x00000000, access: write-only

32/32 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BR[15] w	BR[14] w	BR[13] w	BR[12] w	BR[11] w	BR[10] w	BR[9] w	BR[8] w	BR[7] w	BR[6] w	BR[5] w	BR[4] w	BR[3] w	BR[2] w	BR[1] w	BR[0] w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BS[15] w	BS[14] w	BS[13] w	BS[12] w	BS[11] w	BS[10] w	BS[9] w	BS[8] w	BS[7] w	BS[6] w	BS[5] w	BS[4] w	BS[3] w	BS[2] w	BS[1] w	BS[0] w

Toggle fields

BS[0]

Bit 0: Port x set pin 0.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[1]

Bit 1: Port x set pin 1.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[2]

Bit 2: Port x set pin 2.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[3]

Bit 3: Port x set pin 3.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[4]

Bit 4: Port x set pin 4.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[5]

Bit 5: Port x set pin 5.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[6]

Bit 6: Port x set pin 6.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[7]

Bit 7: Port x set pin 7.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[8]

Bit 8: Port x set pin 8.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[9]

Bit 9: Port x set pin 9.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[10]

Bit 10: Port x set pin 10.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[11]

Bit 11: Port x set pin 11.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[12]

Bit 12: Port x set pin 12.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[13]

Bit 13: Port x set pin 13.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[14]

Bit 14: Port x set pin 14.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[15]

Bit 15: Port x set pin 15.

Allowed values:
1: Set: Sets the corresponding ODx bit

BR[0]

Bit 16: Port x reset pin 0.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[1]

Bit 17: Port x reset pin 1.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[2]

Bit 18: Port x reset pin 2.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[3]

Bit 19: Port x reset pin 3.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[4]

Bit 20: Port x reset pin 4.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[5]

Bit 21: Port x reset pin 5.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[6]

Bit 22: Port x reset pin 6.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[7]

Bit 23: Port x reset pin 7.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[8]

Bit 24: Port x reset pin 8.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[9]

Bit 25: Port x reset pin 9.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[10]

Bit 26: Port x reset pin 10.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[11]

Bit 27: Port x reset pin 11.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[12]

Bit 28: Port x reset pin 12.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[13]

Bit 29: Port x reset pin 13.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[14]

Bit 30: Port x reset pin 14.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[15]

Bit 31: Port x reset pin 15.

Allowed values:
1: Reset: Resets the corresponding ODx bit

LCKR

GPIO port configuration lock register

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

17/17 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															LCKK rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
LCK[15] rw	LCK[14] rw	LCK[13] rw	LCK[12] rw	LCK[11] rw	LCK[10] rw	LCK[9] rw	LCK[8] rw	LCK[7] rw	LCK[6] rw	LCK[5] rw	LCK[4] rw	LCK[3] rw	LCK[2] rw	LCK[1] rw	LCK[0] rw

Toggle fields

LCK[0]

Bit 0: Port x lock pin 0.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[1]

Bit 1: Port x lock pin 1.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[2]

Bit 2: Port x lock pin 2.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[3]

Bit 3: Port x lock pin 3.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[4]

Bit 4: Port x lock pin 4.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[5]

Bit 5: Port x lock pin 5.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[6]

Bit 6: Port x lock pin 6.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[7]

Bit 7: Port x lock pin 7.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[8]

Bit 8: Port x lock pin 8.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[9]

Bit 9: Port x lock pin 9.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[10]

Bit 10: Port x lock pin 10.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[11]

Bit 11: Port x lock pin 11.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[12]

Bit 12: Port x lock pin 12.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[13]

Bit 13: Port x lock pin 13.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[14]

Bit 14: Port x lock pin 14.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[15]

Bit 15: Port x lock pin 15.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCKK

Bit 16: Port x lock bit y (y= 0..15).

Allowed values:
0: NotActive: Port configuration lock key not active
1: Active: Port configuration lock key active

AFRL

GPIO alternate function low register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AFR[EL7] rw				AFR[EL6] rw				AFR[EL5] rw				AFR[EL4] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AFR[EL3] rw				AFR[EL2] rw				AFR[EL1] rw				AFR[EL0] rw

Toggle fields

AFR[EL0]

Bits 0-3: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL1]

Bits 4-7: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL2]

Bits 8-11: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL3]

Bits 12-15: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL4]

Bits 16-19: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL5]

Bits 20-23: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL6]

Bits 24-27: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL7]

Bits 28-31: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFRH

GPIO alternate function high register

Offset: 0x24, size: 32, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AFR[EL15] rw				AFR[EL14] rw				AFR[EL13] rw				AFR[EL12] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AFR[EL11] rw				AFR[EL10] rw				AFR[EL9] rw				AFR[EL8] rw

Toggle fields

AFR[EL8]

Bits 0-3: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL9]

Bits 4-7: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL10]

Bits 8-11: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL11]

Bits 12-15: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL12]

Bits 16-19: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL13]

Bits 20-23: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL14]

Bits 24-27: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL15]

Bits 28-31: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

BRR

port bit reset register

Offset: 0x28, size: 32, reset: 0x00000000, access: write-only

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BR[15] w	BR[14] w	BR[13] w	BR[12] w	BR[11] w	BR[10] w	BR[9] w	BR[8] w	BR[7] w	BR[6] w	BR[5] w	BR[4] w	BR[3] w	BR[2] w	BR[1] w	BR[0] w

Toggle fields

BR[0]

Bit 0: Port x reset pin 0.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[1]

Bit 1: Port x reset pin 1.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[2]

Bit 2: Port x reset pin 2.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[3]

Bit 3: Port x reset pin 3.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[4]

Bit 4: Port x reset pin 4.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[5]

Bit 5: Port x reset pin 5.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[6]

Bit 6: Port x reset pin 6.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[7]

Bit 7: Port x reset pin 7.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[8]

Bit 8: Port x reset pin 8.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[9]

Bit 9: Port x reset pin 9.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[10]

Bit 10: Port x reset pin 10.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[11]

Bit 11: Port x reset pin 11.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[12]

Bit 12: Port x reset pin 12.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[13]

Bit 13: Port x reset pin 13.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[14]

Bit 14: Port x reset pin 14.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[15]

Bit 15: Port x reset pin 15.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

GPIOC

0x50000800: General-purpose I/Os

177/177 fields covered.

Toggle register map

Offset	Name	31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	MODER	MODER[15]		MODER[14]		MODER[13]		MODER[12]		MODER[11]		MODER[10]		MODER[9]		MODER[8]		MODER[7]		MODER[6]		MODER[5]		MODER[4]		MODER[3]		MODER[2]		MODER[1]		MODER[0]
0x4	OTYPER																	OT[15]	OT[14]	OT[13]	OT[12]	OT[11]	OT[10]	OT[9]	OT[8]	OT[7]	OT[6]	OT[5]	OT[4]	OT[3]	OT[2]	OT[1]	OT[0]
0x8	OSPEEDR	OSPEEDR[15]		OSPEEDR[14]		OSPEEDR[13]		OSPEEDR[12]		OSPEEDR[11]		OSPEEDR[10]		OSPEEDR[9]		OSPEEDR[8]		OSPEEDR[7]		OSPEEDR[6]		OSPEEDR[5]		OSPEEDR[4]		OSPEEDR[3]		OSPEEDR[2]		OSPEEDR[1]		OSPEEDR[0]
0xc	PUPDR	PUPDR[15]		PUPDR[14]		PUPDR[13]		PUPDR[12]		PUPDR[11]		PUPDR[10]		PUPDR[9]		PUPDR[8]		PUPDR[7]		PUPDR[6]		PUPDR[5]		PUPDR[4]		PUPDR[3]		PUPDR[2]		PUPDR[1]		PUPDR[0]
0x10	IDR																	IDR[15]	IDR[14]	IDR[13]	IDR[12]	IDR[11]	IDR[10]	IDR[9]	IDR[8]	IDR[7]	IDR[6]	IDR[5]	IDR[4]	IDR[3]	IDR[2]	IDR[1]	IDR[0]
0x14	ODR																	ODR[15]	ODR[14]	ODR[13]	ODR[12]	ODR[11]	ODR[10]	ODR[9]	ODR[8]	ODR[7]	ODR[6]	ODR[5]	ODR[4]	ODR[3]	ODR[2]	ODR[1]	ODR[0]
0x18	BSRR	BR[15]	BR[14]	BR[13]	BR[12]	BR[11]	BR[10]	BR[9]	BR[8]	BR[7]	BR[6]	BR[5]	BR[4]	BR[3]	BR[2]	BR[1]	BR[0]	BS[15]	BS[14]	BS[13]	BS[12]	BS[11]	BS[10]	BS[9]	BS[8]	BS[7]	BS[6]	BS[5]	BS[4]	BS[3]	BS[2]	BS[1]	BS[0]
0x1c	LCKR																LCKK	LCK[15]	LCK[14]	LCK[13]	LCK[12]	LCK[11]	LCK[10]	LCK[9]	LCK[8]	LCK[7]	LCK[6]	LCK[5]	LCK[4]	LCK[3]	LCK[2]	LCK[1]	LCK[0]
0x20	AFRL	AFR[EL7]				AFR[EL6]				AFR[EL5]				AFR[EL4]				AFR[EL3]				AFR[EL2]				AFR[EL1]				AFR[EL0]
0x24	AFRH	AFR[EL15]				AFR[EL14]				AFR[EL13]				AFR[EL12]				AFR[EL11]				AFR[EL10]				AFR[EL9]				AFR[EL8]
0x28	BRR																	BR[15]	BR[14]	BR[13]	BR[12]	BR[11]	BR[10]	BR[9]	BR[8]	BR[7]	BR[6]	BR[5]	BR[4]	BR[3]	BR[2]	BR[1]	BR[0]

Toggle registers

MODER

GPIO port mode register

Offset: 0x0, size: 32, reset: 0xFFFFFFFF, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MODER[15] rw		MODER[14] rw		MODER[13] rw		MODER[12] rw		MODER[11] rw		MODER[10] rw		MODER[9] rw		MODER[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MODER[7] rw		MODER[6] rw		MODER[5] rw		MODER[4] rw		MODER[3] rw		MODER[2] rw		MODER[1] rw		MODER[0] rw

Toggle fields

MODER[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

OTYPER

GPIO port output type register

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OT[15] rw	OT[14] rw	OT[13] rw	OT[12] rw	OT[11] rw	OT[10] rw	OT[9] rw	OT[8] rw	OT[7] rw	OT[6] rw	OT[5] rw	OT[4] rw	OT[3] rw	OT[2] rw	OT[1] rw	OT[0] rw

Toggle fields

OT[0]

Bit 0: Port x configuration pin 0.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[1]

Bit 1: Port x configuration pin 1.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[2]

Bit 2: Port x configuration pin 2.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[3]

Bit 3: Port x configuration pin 3.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[4]

Bit 4: Port x configuration pin 4.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[5]

Bit 5: Port x configuration pin 5.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[6]

Bit 6: Port x configuration pin 6.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[7]

Bit 7: Port x configuration pin 7.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[8]

Bit 8: Port x configuration pin 8.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[9]

Bit 9: Port x configuration pin 9.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[10]

Bit 10: Port x configuration pin 10.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[11]

Bit 11: Port x configuration pin 11.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[12]

Bit 12: Port x configuration pin 12.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[13]

Bit 13: Port x configuration pin 13.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[14]

Bit 14: Port x configuration pin 14.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[15]

Bit 15: Port x configuration pin 15.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OSPEEDR

GPIO port output speed register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OSPEEDR[15] rw		OSPEEDR[14] rw		OSPEEDR[13] rw		OSPEEDR[12] rw		OSPEEDR[11] rw		OSPEEDR[10] rw		OSPEEDR[9] rw		OSPEEDR[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OSPEEDR[7] rw		OSPEEDR[6] rw		OSPEEDR[5] rw		OSPEEDR[4] rw		OSPEEDR[3] rw		OSPEEDR[2] rw		OSPEEDR[1] rw		OSPEEDR[0] rw

Toggle fields

OSPEEDR[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

PUPDR

GPIO port pull-up/pull-down register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PUPDR[15] rw		PUPDR[14] rw		PUPDR[13] rw		PUPDR[12] rw		PUPDR[11] rw		PUPDR[10] rw		PUPDR[9] rw		PUPDR[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PUPDR[7] rw		PUPDR[6] rw		PUPDR[5] rw		PUPDR[4] rw		PUPDR[3] rw		PUPDR[2] rw		PUPDR[1] rw		PUPDR[0] rw

Toggle fields

PUPDR[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

IDR

GPIO port input data register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-only

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IDR[15] r	IDR[14] r	IDR[13] r	IDR[12] r	IDR[11] r	IDR[10] r	IDR[9] r	IDR[8] r	IDR[7] r	IDR[6] r	IDR[5] r	IDR[4] r	IDR[3] r	IDR[2] r	IDR[1] r	IDR[0] r

Toggle fields

IDR[0]

Bit 0: Port input data pin 0.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[1]

Bit 1: Port input data pin 1.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[2]

Bit 2: Port input data pin 2.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[3]

Bit 3: Port input data pin 3.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[4]

Bit 4: Port input data pin 4.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[5]

Bit 5: Port input data pin 5.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[6]

Bit 6: Port input data pin 6.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[7]

Bit 7: Port input data pin 7.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[8]

Bit 8: Port input data pin 8.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[9]

Bit 9: Port input data pin 9.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[10]

Bit 10: Port input data pin 10.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[11]

Bit 11: Port input data pin 11.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[12]

Bit 12: Port input data pin 12.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[13]

Bit 13: Port input data pin 13.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[14]

Bit 14: Port input data pin 14.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[15]

Bit 15: Port input data pin 15.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

ODR

GPIO port output data register

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ODR[15] rw	ODR[14] rw	ODR[13] rw	ODR[12] rw	ODR[11] rw	ODR[10] rw	ODR[9] rw	ODR[8] rw	ODR[7] rw	ODR[6] rw	ODR[5] rw	ODR[4] rw	ODR[3] rw	ODR[2] rw	ODR[1] rw	ODR[0] rw

Toggle fields

ODR[0]

Bit 0: Port output data pin 0.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[1]

Bit 1: Port output data pin 1.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[2]

Bit 2: Port output data pin 2.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[3]

Bit 3: Port output data pin 3.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[4]

Bit 4: Port output data pin 4.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[5]

Bit 5: Port output data pin 5.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[6]

Bit 6: Port output data pin 6.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[7]

Bit 7: Port output data pin 7.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[8]

Bit 8: Port output data pin 8.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[9]

Bit 9: Port output data pin 9.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[10]

Bit 10: Port output data pin 10.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[11]

Bit 11: Port output data pin 11.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[12]

Bit 12: Port output data pin 12.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[13]

Bit 13: Port output data pin 13.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[14]

Bit 14: Port output data pin 14.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[15]

Bit 15: Port output data pin 15.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

BSRR

GPIO port bit set/reset register

Offset: 0x18, size: 32, reset: 0x00000000, access: write-only

32/32 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BR[15] w	BR[14] w	BR[13] w	BR[12] w	BR[11] w	BR[10] w	BR[9] w	BR[8] w	BR[7] w	BR[6] w	BR[5] w	BR[4] w	BR[3] w	BR[2] w	BR[1] w	BR[0] w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BS[15] w	BS[14] w	BS[13] w	BS[12] w	BS[11] w	BS[10] w	BS[9] w	BS[8] w	BS[7] w	BS[6] w	BS[5] w	BS[4] w	BS[3] w	BS[2] w	BS[1] w	BS[0] w

Toggle fields

BS[0]

Bit 0: Port x set pin 0.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[1]

Bit 1: Port x set pin 1.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[2]

Bit 2: Port x set pin 2.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[3]

Bit 3: Port x set pin 3.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[4]

Bit 4: Port x set pin 4.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[5]

Bit 5: Port x set pin 5.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[6]

Bit 6: Port x set pin 6.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[7]

Bit 7: Port x set pin 7.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[8]

Bit 8: Port x set pin 8.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[9]

Bit 9: Port x set pin 9.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[10]

Bit 10: Port x set pin 10.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[11]

Bit 11: Port x set pin 11.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[12]

Bit 12: Port x set pin 12.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[13]

Bit 13: Port x set pin 13.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[14]

Bit 14: Port x set pin 14.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[15]

Bit 15: Port x set pin 15.

Allowed values:
1: Set: Sets the corresponding ODx bit

BR[0]

Bit 16: Port x reset pin 0.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[1]

Bit 17: Port x reset pin 1.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[2]

Bit 18: Port x reset pin 2.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[3]

Bit 19: Port x reset pin 3.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[4]

Bit 20: Port x reset pin 4.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[5]

Bit 21: Port x reset pin 5.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[6]

Bit 22: Port x reset pin 6.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[7]

Bit 23: Port x reset pin 7.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[8]

Bit 24: Port x reset pin 8.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[9]

Bit 25: Port x reset pin 9.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[10]

Bit 26: Port x reset pin 10.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[11]

Bit 27: Port x reset pin 11.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[12]

Bit 28: Port x reset pin 12.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[13]

Bit 29: Port x reset pin 13.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[14]

Bit 30: Port x reset pin 14.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[15]

Bit 31: Port x reset pin 15.

Allowed values:
1: Reset: Resets the corresponding ODx bit

LCKR

GPIO port configuration lock register

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

17/17 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															LCKK rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
LCK[15] rw	LCK[14] rw	LCK[13] rw	LCK[12] rw	LCK[11] rw	LCK[10] rw	LCK[9] rw	LCK[8] rw	LCK[7] rw	LCK[6] rw	LCK[5] rw	LCK[4] rw	LCK[3] rw	LCK[2] rw	LCK[1] rw	LCK[0] rw

Toggle fields

LCK[0]

Bit 0: Port x lock pin 0.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[1]

Bit 1: Port x lock pin 1.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[2]

Bit 2: Port x lock pin 2.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[3]

Bit 3: Port x lock pin 3.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[4]

Bit 4: Port x lock pin 4.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[5]

Bit 5: Port x lock pin 5.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[6]

Bit 6: Port x lock pin 6.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[7]

Bit 7: Port x lock pin 7.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[8]

Bit 8: Port x lock pin 8.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[9]

Bit 9: Port x lock pin 9.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[10]

Bit 10: Port x lock pin 10.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[11]

Bit 11: Port x lock pin 11.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[12]

Bit 12: Port x lock pin 12.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[13]

Bit 13: Port x lock pin 13.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[14]

Bit 14: Port x lock pin 14.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[15]

Bit 15: Port x lock pin 15.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCKK

Bit 16: Port x lock bit y (y= 0..15).

Allowed values:
0: NotActive: Port configuration lock key not active
1: Active: Port configuration lock key active

AFRL

GPIO alternate function low register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AFR[EL7] rw				AFR[EL6] rw				AFR[EL5] rw				AFR[EL4] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AFR[EL3] rw				AFR[EL2] rw				AFR[EL1] rw				AFR[EL0] rw

Toggle fields

AFR[EL0]

Bits 0-3: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL1]

Bits 4-7: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL2]

Bits 8-11: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL3]

Bits 12-15: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL4]

Bits 16-19: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL5]

Bits 20-23: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL6]

Bits 24-27: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL7]

Bits 28-31: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFRH

GPIO alternate function high register

Offset: 0x24, size: 32, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AFR[EL15] rw				AFR[EL14] rw				AFR[EL13] rw				AFR[EL12] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AFR[EL11] rw				AFR[EL10] rw				AFR[EL9] rw				AFR[EL8] rw

Toggle fields

AFR[EL8]

Bits 0-3: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL9]

Bits 4-7: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL10]

Bits 8-11: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL11]

Bits 12-15: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL12]

Bits 16-19: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL13]

Bits 20-23: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL14]

Bits 24-27: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL15]

Bits 28-31: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

BRR

port bit reset register

Offset: 0x28, size: 32, reset: 0x00000000, access: write-only

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BR[15] w	BR[14] w	BR[13] w	BR[12] w	BR[11] w	BR[10] w	BR[9] w	BR[8] w	BR[7] w	BR[6] w	BR[5] w	BR[4] w	BR[3] w	BR[2] w	BR[1] w	BR[0] w

Toggle fields

BR[0]

Bit 0: Port x reset pin 0.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[1]

Bit 1: Port x reset pin 1.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[2]

Bit 2: Port x reset pin 2.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[3]

Bit 3: Port x reset pin 3.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[4]

Bit 4: Port x reset pin 4.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[5]

Bit 5: Port x reset pin 5.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[6]

Bit 6: Port x reset pin 6.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[7]

Bit 7: Port x reset pin 7.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[8]

Bit 8: Port x reset pin 8.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[9]

Bit 9: Port x reset pin 9.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[10]

Bit 10: Port x reset pin 10.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[11]

Bit 11: Port x reset pin 11.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[12]

Bit 12: Port x reset pin 12.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[13]

Bit 13: Port x reset pin 13.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[14]

Bit 14: Port x reset pin 14.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[15]

Bit 15: Port x reset pin 15.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

GPIOD

0x50000c00: General-purpose I/Os

177/177 fields covered.

Toggle register map

Offset	Name	31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	MODER	MODER[15]		MODER[14]		MODER[13]		MODER[12]		MODER[11]		MODER[10]		MODER[9]		MODER[8]		MODER[7]		MODER[6]		MODER[5]		MODER[4]		MODER[3]		MODER[2]		MODER[1]		MODER[0]
0x4	OTYPER																	OT[15]	OT[14]	OT[13]	OT[12]	OT[11]	OT[10]	OT[9]	OT[8]	OT[7]	OT[6]	OT[5]	OT[4]	OT[3]	OT[2]	OT[1]	OT[0]
0x8	OSPEEDR	OSPEEDR[15]		OSPEEDR[14]		OSPEEDR[13]		OSPEEDR[12]		OSPEEDR[11]		OSPEEDR[10]		OSPEEDR[9]		OSPEEDR[8]		OSPEEDR[7]		OSPEEDR[6]		OSPEEDR[5]		OSPEEDR[4]		OSPEEDR[3]		OSPEEDR[2]		OSPEEDR[1]		OSPEEDR[0]
0xc	PUPDR	PUPDR[15]		PUPDR[14]		PUPDR[13]		PUPDR[12]		PUPDR[11]		PUPDR[10]		PUPDR[9]		PUPDR[8]		PUPDR[7]		PUPDR[6]		PUPDR[5]		PUPDR[4]		PUPDR[3]		PUPDR[2]		PUPDR[1]		PUPDR[0]
0x10	IDR																	IDR[15]	IDR[14]	IDR[13]	IDR[12]	IDR[11]	IDR[10]	IDR[9]	IDR[8]	IDR[7]	IDR[6]	IDR[5]	IDR[4]	IDR[3]	IDR[2]	IDR[1]	IDR[0]
0x14	ODR																	ODR[15]	ODR[14]	ODR[13]	ODR[12]	ODR[11]	ODR[10]	ODR[9]	ODR[8]	ODR[7]	ODR[6]	ODR[5]	ODR[4]	ODR[3]	ODR[2]	ODR[1]	ODR[0]
0x18	BSRR	BR[15]	BR[14]	BR[13]	BR[12]	BR[11]	BR[10]	BR[9]	BR[8]	BR[7]	BR[6]	BR[5]	BR[4]	BR[3]	BR[2]	BR[1]	BR[0]	BS[15]	BS[14]	BS[13]	BS[12]	BS[11]	BS[10]	BS[9]	BS[8]	BS[7]	BS[6]	BS[5]	BS[4]	BS[3]	BS[2]	BS[1]	BS[0]
0x1c	LCKR																LCKK	LCK[15]	LCK[14]	LCK[13]	LCK[12]	LCK[11]	LCK[10]	LCK[9]	LCK[8]	LCK[7]	LCK[6]	LCK[5]	LCK[4]	LCK[3]	LCK[2]	LCK[1]	LCK[0]
0x20	AFRL	AFR[EL7]				AFR[EL6]				AFR[EL5]				AFR[EL4]				AFR[EL3]				AFR[EL2]				AFR[EL1]				AFR[EL0]
0x24	AFRH	AFR[EL15]				AFR[EL14]				AFR[EL13]				AFR[EL12]				AFR[EL11]				AFR[EL10]				AFR[EL9]				AFR[EL8]
0x28	BRR																	BR[15]	BR[14]	BR[13]	BR[12]	BR[11]	BR[10]	BR[9]	BR[8]	BR[7]	BR[6]	BR[5]	BR[4]	BR[3]	BR[2]	BR[1]	BR[0]

Toggle registers

MODER

GPIO port mode register

Offset: 0x0, size: 32, reset: 0xFFFFFFFF, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MODER[15] rw		MODER[14] rw		MODER[13] rw		MODER[12] rw		MODER[11] rw		MODER[10] rw		MODER[9] rw		MODER[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MODER[7] rw		MODER[6] rw		MODER[5] rw		MODER[4] rw		MODER[3] rw		MODER[2] rw		MODER[1] rw		MODER[0] rw

Toggle fields

MODER[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

OTYPER

GPIO port output type register

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OT[15] rw	OT[14] rw	OT[13] rw	OT[12] rw	OT[11] rw	OT[10] rw	OT[9] rw	OT[8] rw	OT[7] rw	OT[6] rw	OT[5] rw	OT[4] rw	OT[3] rw	OT[2] rw	OT[1] rw	OT[0] rw

Toggle fields

OT[0]

Bit 0: Port x configuration pin 0.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[1]

Bit 1: Port x configuration pin 1.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[2]

Bit 2: Port x configuration pin 2.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[3]

Bit 3: Port x configuration pin 3.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[4]

Bit 4: Port x configuration pin 4.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[5]

Bit 5: Port x configuration pin 5.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[6]

Bit 6: Port x configuration pin 6.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[7]

Bit 7: Port x configuration pin 7.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[8]

Bit 8: Port x configuration pin 8.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[9]

Bit 9: Port x configuration pin 9.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[10]

Bit 10: Port x configuration pin 10.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[11]

Bit 11: Port x configuration pin 11.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[12]

Bit 12: Port x configuration pin 12.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[13]

Bit 13: Port x configuration pin 13.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[14]

Bit 14: Port x configuration pin 14.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[15]

Bit 15: Port x configuration pin 15.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OSPEEDR

GPIO port output speed register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OSPEEDR[15] rw		OSPEEDR[14] rw		OSPEEDR[13] rw		OSPEEDR[12] rw		OSPEEDR[11] rw		OSPEEDR[10] rw		OSPEEDR[9] rw		OSPEEDR[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OSPEEDR[7] rw		OSPEEDR[6] rw		OSPEEDR[5] rw		OSPEEDR[4] rw		OSPEEDR[3] rw		OSPEEDR[2] rw		OSPEEDR[1] rw		OSPEEDR[0] rw

Toggle fields

OSPEEDR[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

PUPDR

GPIO port pull-up/pull-down register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PUPDR[15] rw		PUPDR[14] rw		PUPDR[13] rw		PUPDR[12] rw		PUPDR[11] rw		PUPDR[10] rw		PUPDR[9] rw		PUPDR[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PUPDR[7] rw		PUPDR[6] rw		PUPDR[5] rw		PUPDR[4] rw		PUPDR[3] rw		PUPDR[2] rw		PUPDR[1] rw		PUPDR[0] rw

Toggle fields

PUPDR[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

IDR

GPIO port input data register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-only

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IDR[15] r	IDR[14] r	IDR[13] r	IDR[12] r	IDR[11] r	IDR[10] r	IDR[9] r	IDR[8] r	IDR[7] r	IDR[6] r	IDR[5] r	IDR[4] r	IDR[3] r	IDR[2] r	IDR[1] r	IDR[0] r

Toggle fields

IDR[0]

Bit 0: Port input data pin 0.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[1]

Bit 1: Port input data pin 1.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[2]

Bit 2: Port input data pin 2.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[3]

Bit 3: Port input data pin 3.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[4]

Bit 4: Port input data pin 4.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[5]

Bit 5: Port input data pin 5.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[6]

Bit 6: Port input data pin 6.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[7]

Bit 7: Port input data pin 7.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[8]

Bit 8: Port input data pin 8.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[9]

Bit 9: Port input data pin 9.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[10]

Bit 10: Port input data pin 10.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[11]

Bit 11: Port input data pin 11.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[12]

Bit 12: Port input data pin 12.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[13]

Bit 13: Port input data pin 13.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[14]

Bit 14: Port input data pin 14.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[15]

Bit 15: Port input data pin 15.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

ODR

GPIO port output data register

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ODR[15] rw	ODR[14] rw	ODR[13] rw	ODR[12] rw	ODR[11] rw	ODR[10] rw	ODR[9] rw	ODR[8] rw	ODR[7] rw	ODR[6] rw	ODR[5] rw	ODR[4] rw	ODR[3] rw	ODR[2] rw	ODR[1] rw	ODR[0] rw

Toggle fields

ODR[0]

Bit 0: Port output data pin 0.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[1]

Bit 1: Port output data pin 1.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[2]

Bit 2: Port output data pin 2.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[3]

Bit 3: Port output data pin 3.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[4]

Bit 4: Port output data pin 4.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[5]

Bit 5: Port output data pin 5.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[6]

Bit 6: Port output data pin 6.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[7]

Bit 7: Port output data pin 7.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[8]

Bit 8: Port output data pin 8.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[9]

Bit 9: Port output data pin 9.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[10]

Bit 10: Port output data pin 10.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[11]

Bit 11: Port output data pin 11.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[12]

Bit 12: Port output data pin 12.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[13]

Bit 13: Port output data pin 13.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[14]

Bit 14: Port output data pin 14.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[15]

Bit 15: Port output data pin 15.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

BSRR

GPIO port bit set/reset register

Offset: 0x18, size: 32, reset: 0x00000000, access: write-only

32/32 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BR[15] w	BR[14] w	BR[13] w	BR[12] w	BR[11] w	BR[10] w	BR[9] w	BR[8] w	BR[7] w	BR[6] w	BR[5] w	BR[4] w	BR[3] w	BR[2] w	BR[1] w	BR[0] w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BS[15] w	BS[14] w	BS[13] w	BS[12] w	BS[11] w	BS[10] w	BS[9] w	BS[8] w	BS[7] w	BS[6] w	BS[5] w	BS[4] w	BS[3] w	BS[2] w	BS[1] w	BS[0] w

Toggle fields

BS[0]

Bit 0: Port x set pin 0.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[1]

Bit 1: Port x set pin 1.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[2]

Bit 2: Port x set pin 2.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[3]

Bit 3: Port x set pin 3.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[4]

Bit 4: Port x set pin 4.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[5]

Bit 5: Port x set pin 5.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[6]

Bit 6: Port x set pin 6.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[7]

Bit 7: Port x set pin 7.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[8]

Bit 8: Port x set pin 8.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[9]

Bit 9: Port x set pin 9.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[10]

Bit 10: Port x set pin 10.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[11]

Bit 11: Port x set pin 11.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[12]

Bit 12: Port x set pin 12.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[13]

Bit 13: Port x set pin 13.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[14]

Bit 14: Port x set pin 14.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[15]

Bit 15: Port x set pin 15.

Allowed values:
1: Set: Sets the corresponding ODx bit

BR[0]

Bit 16: Port x reset pin 0.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[1]

Bit 17: Port x reset pin 1.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[2]

Bit 18: Port x reset pin 2.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[3]

Bit 19: Port x reset pin 3.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[4]

Bit 20: Port x reset pin 4.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[5]

Bit 21: Port x reset pin 5.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[6]

Bit 22: Port x reset pin 6.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[7]

Bit 23: Port x reset pin 7.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[8]

Bit 24: Port x reset pin 8.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[9]

Bit 25: Port x reset pin 9.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[10]

Bit 26: Port x reset pin 10.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[11]

Bit 27: Port x reset pin 11.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[12]

Bit 28: Port x reset pin 12.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[13]

Bit 29: Port x reset pin 13.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[14]

Bit 30: Port x reset pin 14.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[15]

Bit 31: Port x reset pin 15.

Allowed values:
1: Reset: Resets the corresponding ODx bit

LCKR

GPIO port configuration lock register

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

17/17 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															LCKK rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
LCK[15] rw	LCK[14] rw	LCK[13] rw	LCK[12] rw	LCK[11] rw	LCK[10] rw	LCK[9] rw	LCK[8] rw	LCK[7] rw	LCK[6] rw	LCK[5] rw	LCK[4] rw	LCK[3] rw	LCK[2] rw	LCK[1] rw	LCK[0] rw

Toggle fields

LCK[0]

Bit 0: Port x lock pin 0.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[1]

Bit 1: Port x lock pin 1.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[2]

Bit 2: Port x lock pin 2.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[3]

Bit 3: Port x lock pin 3.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[4]

Bit 4: Port x lock pin 4.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[5]

Bit 5: Port x lock pin 5.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[6]

Bit 6: Port x lock pin 6.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[7]

Bit 7: Port x lock pin 7.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[8]

Bit 8: Port x lock pin 8.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[9]

Bit 9: Port x lock pin 9.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[10]

Bit 10: Port x lock pin 10.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[11]

Bit 11: Port x lock pin 11.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[12]

Bit 12: Port x lock pin 12.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[13]

Bit 13: Port x lock pin 13.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[14]

Bit 14: Port x lock pin 14.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[15]

Bit 15: Port x lock pin 15.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCKK

Bit 16: Port x lock bit y (y= 0..15).

Allowed values:
0: NotActive: Port configuration lock key not active
1: Active: Port configuration lock key active

AFRL

GPIO alternate function low register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AFR[EL7] rw				AFR[EL6] rw				AFR[EL5] rw				AFR[EL4] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AFR[EL3] rw				AFR[EL2] rw				AFR[EL1] rw				AFR[EL0] rw

Toggle fields

AFR[EL0]

Bits 0-3: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL1]

Bits 4-7: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL2]

Bits 8-11: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL3]

Bits 12-15: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL4]

Bits 16-19: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL5]

Bits 20-23: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL6]

Bits 24-27: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL7]

Bits 28-31: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFRH

GPIO alternate function high register

Offset: 0x24, size: 32, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AFR[EL15] rw				AFR[EL14] rw				AFR[EL13] rw				AFR[EL12] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AFR[EL11] rw				AFR[EL10] rw				AFR[EL9] rw				AFR[EL8] rw

Toggle fields

AFR[EL8]

Bits 0-3: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL9]

Bits 4-7: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL10]

Bits 8-11: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL11]

Bits 12-15: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL12]

Bits 16-19: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL13]

Bits 20-23: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL14]

Bits 24-27: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL15]

Bits 28-31: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

BRR

port bit reset register

Offset: 0x28, size: 32, reset: 0x00000000, access: write-only

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BR[15] w	BR[14] w	BR[13] w	BR[12] w	BR[11] w	BR[10] w	BR[9] w	BR[8] w	BR[7] w	BR[6] w	BR[5] w	BR[4] w	BR[3] w	BR[2] w	BR[1] w	BR[0] w

Toggle fields

BR[0]

Bit 0: Port x reset pin 0.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[1]

Bit 1: Port x reset pin 1.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[2]

Bit 2: Port x reset pin 2.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[3]

Bit 3: Port x reset pin 3.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[4]

Bit 4: Port x reset pin 4.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[5]

Bit 5: Port x reset pin 5.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[6]

Bit 6: Port x reset pin 6.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[7]

Bit 7: Port x reset pin 7.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[8]

Bit 8: Port x reset pin 8.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[9]

Bit 9: Port x reset pin 9.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[10]

Bit 10: Port x reset pin 10.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[11]

Bit 11: Port x reset pin 11.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[12]

Bit 12: Port x reset pin 12.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[13]

Bit 13: Port x reset pin 13.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[14]

Bit 14: Port x reset pin 14.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[15]

Bit 15: Port x reset pin 15.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

GPIOF

0x50001400: General-purpose I/Os

177/177 fields covered.

Toggle register map

Offset	Name	31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	MODER	MODER[15]		MODER[14]		MODER[13]		MODER[12]		MODER[11]		MODER[10]		MODER[9]		MODER[8]		MODER[7]		MODER[6]		MODER[5]		MODER[4]		MODER[3]		MODER[2]		MODER[1]		MODER[0]
0x4	OTYPER																	OT[15]	OT[14]	OT[13]	OT[12]	OT[11]	OT[10]	OT[9]	OT[8]	OT[7]	OT[6]	OT[5]	OT[4]	OT[3]	OT[2]	OT[1]	OT[0]
0x8	OSPEEDR	OSPEEDR[15]		OSPEEDR[14]		OSPEEDR[13]		OSPEEDR[12]		OSPEEDR[11]		OSPEEDR[10]		OSPEEDR[9]		OSPEEDR[8]		OSPEEDR[7]		OSPEEDR[6]		OSPEEDR[5]		OSPEEDR[4]		OSPEEDR[3]		OSPEEDR[2]		OSPEEDR[1]		OSPEEDR[0]
0xc	PUPDR	PUPDR[15]		PUPDR[14]		PUPDR[13]		PUPDR[12]		PUPDR[11]		PUPDR[10]		PUPDR[9]		PUPDR[8]		PUPDR[7]		PUPDR[6]		PUPDR[5]		PUPDR[4]		PUPDR[3]		PUPDR[2]		PUPDR[1]		PUPDR[0]
0x10	IDR																	IDR[15]	IDR[14]	IDR[13]	IDR[12]	IDR[11]	IDR[10]	IDR[9]	IDR[8]	IDR[7]	IDR[6]	IDR[5]	IDR[4]	IDR[3]	IDR[2]	IDR[1]	IDR[0]
0x14	ODR																	ODR[15]	ODR[14]	ODR[13]	ODR[12]	ODR[11]	ODR[10]	ODR[9]	ODR[8]	ODR[7]	ODR[6]	ODR[5]	ODR[4]	ODR[3]	ODR[2]	ODR[1]	ODR[0]
0x18	BSRR	BR[15]	BR[14]	BR[13]	BR[12]	BR[11]	BR[10]	BR[9]	BR[8]	BR[7]	BR[6]	BR[5]	BR[4]	BR[3]	BR[2]	BR[1]	BR[0]	BS[15]	BS[14]	BS[13]	BS[12]	BS[11]	BS[10]	BS[9]	BS[8]	BS[7]	BS[6]	BS[5]	BS[4]	BS[3]	BS[2]	BS[1]	BS[0]
0x1c	LCKR																LCKK	LCK[15]	LCK[14]	LCK[13]	LCK[12]	LCK[11]	LCK[10]	LCK[9]	LCK[8]	LCK[7]	LCK[6]	LCK[5]	LCK[4]	LCK[3]	LCK[2]	LCK[1]	LCK[0]
0x20	AFRL	AFR[EL7]				AFR[EL6]				AFR[EL5]				AFR[EL4]				AFR[EL3]				AFR[EL2]				AFR[EL1]				AFR[EL0]
0x24	AFRH	AFR[EL15]				AFR[EL14]				AFR[EL13]				AFR[EL12]				AFR[EL11]				AFR[EL10]				AFR[EL9]				AFR[EL8]
0x28	BRR																	BR[15]	BR[14]	BR[13]	BR[12]	BR[11]	BR[10]	BR[9]	BR[8]	BR[7]	BR[6]	BR[5]	BR[4]	BR[3]	BR[2]	BR[1]	BR[0]

Toggle registers

MODER

GPIO port mode register

Offset: 0x0, size: 32, reset: 0xFFFFFFFF, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MODER[15] rw		MODER[14] rw		MODER[13] rw		MODER[12] rw		MODER[11] rw		MODER[10] rw		MODER[9] rw		MODER[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MODER[7] rw		MODER[6] rw		MODER[5] rw		MODER[4] rw		MODER[3] rw		MODER[2] rw		MODER[1] rw		MODER[0] rw

Toggle fields

MODER[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: Input: Input mode
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

OTYPER

GPIO port output type register

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OT[15] rw	OT[14] rw	OT[13] rw	OT[12] rw	OT[11] rw	OT[10] rw	OT[9] rw	OT[8] rw	OT[7] rw	OT[6] rw	OT[5] rw	OT[4] rw	OT[3] rw	OT[2] rw	OT[1] rw	OT[0] rw

Toggle fields

OT[0]

Bit 0: Port x configuration pin 0.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[1]

Bit 1: Port x configuration pin 1.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[2]

Bit 2: Port x configuration pin 2.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[3]

Bit 3: Port x configuration pin 3.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[4]

Bit 4: Port x configuration pin 4.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[5]

Bit 5: Port x configuration pin 5.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[6]

Bit 6: Port x configuration pin 6.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[7]

Bit 7: Port x configuration pin 7.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[8]

Bit 8: Port x configuration pin 8.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[9]

Bit 9: Port x configuration pin 9.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[10]

Bit 10: Port x configuration pin 10.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[11]

Bit 11: Port x configuration pin 11.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[12]

Bit 12: Port x configuration pin 12.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[13]

Bit 13: Port x configuration pin 13.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[14]

Bit 14: Port x configuration pin 14.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT[15]

Bit 15: Port x configuration pin 15.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OSPEEDR

GPIO port output speed register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OSPEEDR[15] rw		OSPEEDR[14] rw		OSPEEDR[13] rw		OSPEEDR[12] rw		OSPEEDR[11] rw		OSPEEDR[10] rw		OSPEEDR[9] rw		OSPEEDR[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OSPEEDR[7] rw		OSPEEDR[6] rw		OSPEEDR[5] rw		OSPEEDR[4] rw		OSPEEDR[3] rw		OSPEEDR[2] rw		OSPEEDR[1] rw		OSPEEDR[0] rw

Toggle fields

OSPEEDR[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

PUPDR

GPIO port pull-up/pull-down register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PUPDR[15] rw		PUPDR[14] rw		PUPDR[13] rw		PUPDR[12] rw		PUPDR[11] rw		PUPDR[10] rw		PUPDR[9] rw		PUPDR[8] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PUPDR[7] rw		PUPDR[6] rw		PUPDR[5] rw		PUPDR[4] rw		PUPDR[3] rw		PUPDR[2] rw		PUPDR[1] rw		PUPDR[0] rw

Toggle fields

PUPDR[0]

Bits 0-1: Port x configuration pin 0.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[1]

Bits 2-3: Port x configuration pin 1.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[2]

Bits 4-5: Port x configuration pin 2.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[3]

Bits 6-7: Port x configuration pin 3.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[4]

Bits 8-9: Port x configuration pin 4.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[5]

Bits 10-11: Port x configuration pin 5.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[6]

Bits 12-13: Port x configuration pin 6.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[7]

Bits 14-15: Port x configuration pin 7.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[8]

Bits 16-17: Port x configuration pin 8.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[9]

Bits 18-19: Port x configuration pin 9.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[10]

Bits 20-21: Port x configuration pin 10.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[11]

Bits 22-23: Port x configuration pin 11.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[12]

Bits 24-25: Port x configuration pin 12.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[13]

Bits 26-27: Port x configuration pin 13.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[14]

Bits 28-29: Port x configuration pin 14.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR[15]

Bits 30-31: Port x configuration pin 15.

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

IDR

GPIO port input data register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-only

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IDR[15] r	IDR[14] r	IDR[13] r	IDR[12] r	IDR[11] r	IDR[10] r	IDR[9] r	IDR[8] r	IDR[7] r	IDR[6] r	IDR[5] r	IDR[4] r	IDR[3] r	IDR[2] r	IDR[1] r	IDR[0] r

Toggle fields

IDR[0]

Bit 0: Port input data pin 0.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[1]

Bit 1: Port input data pin 1.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[2]

Bit 2: Port input data pin 2.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[3]

Bit 3: Port input data pin 3.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[4]

Bit 4: Port input data pin 4.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[5]

Bit 5: Port input data pin 5.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[6]

Bit 6: Port input data pin 6.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[7]

Bit 7: Port input data pin 7.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[8]

Bit 8: Port input data pin 8.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[9]

Bit 9: Port input data pin 9.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[10]

Bit 10: Port input data pin 10.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[11]

Bit 11: Port input data pin 11.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[12]

Bit 12: Port input data pin 12.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[13]

Bit 13: Port input data pin 13.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[14]

Bit 14: Port input data pin 14.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

IDR[15]

Bit 15: Port input data pin 15.

Allowed values:
0: Low: Input is logic low
1: High: Input is logic high

ODR

GPIO port output data register

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ODR[15] rw	ODR[14] rw	ODR[13] rw	ODR[12] rw	ODR[11] rw	ODR[10] rw	ODR[9] rw	ODR[8] rw	ODR[7] rw	ODR[6] rw	ODR[5] rw	ODR[4] rw	ODR[3] rw	ODR[2] rw	ODR[1] rw	ODR[0] rw

Toggle fields

ODR[0]

Bit 0: Port output data pin 0.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[1]

Bit 1: Port output data pin 1.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[2]

Bit 2: Port output data pin 2.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[3]

Bit 3: Port output data pin 3.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[4]

Bit 4: Port output data pin 4.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[5]

Bit 5: Port output data pin 5.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[6]

Bit 6: Port output data pin 6.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[7]

Bit 7: Port output data pin 7.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[8]

Bit 8: Port output data pin 8.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[9]

Bit 9: Port output data pin 9.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[10]

Bit 10: Port output data pin 10.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[11]

Bit 11: Port output data pin 11.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[12]

Bit 12: Port output data pin 12.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[13]

Bit 13: Port output data pin 13.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[14]

Bit 14: Port output data pin 14.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

ODR[15]

Bit 15: Port output data pin 15.

Allowed values:
0: Low: Set output to logic low
1: High: Set output to logic high

BSRR

GPIO port bit set/reset register

Offset: 0x18, size: 32, reset: 0x00000000, access: write-only

32/32 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BR[15] w	BR[14] w	BR[13] w	BR[12] w	BR[11] w	BR[10] w	BR[9] w	BR[8] w	BR[7] w	BR[6] w	BR[5] w	BR[4] w	BR[3] w	BR[2] w	BR[1] w	BR[0] w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BS[15] w	BS[14] w	BS[13] w	BS[12] w	BS[11] w	BS[10] w	BS[9] w	BS[8] w	BS[7] w	BS[6] w	BS[5] w	BS[4] w	BS[3] w	BS[2] w	BS[1] w	BS[0] w

Toggle fields

BS[0]

Bit 0: Port x set pin 0.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[1]

Bit 1: Port x set pin 1.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[2]

Bit 2: Port x set pin 2.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[3]

Bit 3: Port x set pin 3.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[4]

Bit 4: Port x set pin 4.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[5]

Bit 5: Port x set pin 5.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[6]

Bit 6: Port x set pin 6.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[7]

Bit 7: Port x set pin 7.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[8]

Bit 8: Port x set pin 8.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[9]

Bit 9: Port x set pin 9.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[10]

Bit 10: Port x set pin 10.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[11]

Bit 11: Port x set pin 11.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[12]

Bit 12: Port x set pin 12.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[13]

Bit 13: Port x set pin 13.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[14]

Bit 14: Port x set pin 14.

Allowed values:
1: Set: Sets the corresponding ODx bit

BS[15]

Bit 15: Port x set pin 15.

Allowed values:
1: Set: Sets the corresponding ODx bit

BR[0]

Bit 16: Port x reset pin 0.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[1]

Bit 17: Port x reset pin 1.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[2]

Bit 18: Port x reset pin 2.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[3]

Bit 19: Port x reset pin 3.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[4]

Bit 20: Port x reset pin 4.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[5]

Bit 21: Port x reset pin 5.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[6]

Bit 22: Port x reset pin 6.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[7]

Bit 23: Port x reset pin 7.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[8]

Bit 24: Port x reset pin 8.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[9]

Bit 25: Port x reset pin 9.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[10]

Bit 26: Port x reset pin 10.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[11]

Bit 27: Port x reset pin 11.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[12]

Bit 28: Port x reset pin 12.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[13]

Bit 29: Port x reset pin 13.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[14]

Bit 30: Port x reset pin 14.

Allowed values:
1: Reset: Resets the corresponding ODx bit

BR[15]

Bit 31: Port x reset pin 15.

Allowed values:
1: Reset: Resets the corresponding ODx bit

LCKR

GPIO port configuration lock register

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

17/17 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															LCKK rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
LCK[15] rw	LCK[14] rw	LCK[13] rw	LCK[12] rw	LCK[11] rw	LCK[10] rw	LCK[9] rw	LCK[8] rw	LCK[7] rw	LCK[6] rw	LCK[5] rw	LCK[4] rw	LCK[3] rw	LCK[2] rw	LCK[1] rw	LCK[0] rw

Toggle fields

LCK[0]

Bit 0: Port x lock pin 0.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[1]

Bit 1: Port x lock pin 1.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[2]

Bit 2: Port x lock pin 2.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[3]

Bit 3: Port x lock pin 3.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[4]

Bit 4: Port x lock pin 4.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[5]

Bit 5: Port x lock pin 5.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[6]

Bit 6: Port x lock pin 6.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[7]

Bit 7: Port x lock pin 7.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[8]

Bit 8: Port x lock pin 8.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[9]

Bit 9: Port x lock pin 9.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[10]

Bit 10: Port x lock pin 10.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[11]

Bit 11: Port x lock pin 11.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[12]

Bit 12: Port x lock pin 12.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[13]

Bit 13: Port x lock pin 13.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[14]

Bit 14: Port x lock pin 14.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK[15]

Bit 15: Port x lock pin 15.

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCKK

Bit 16: Port x lock bit y (y= 0..15).

Allowed values:
0: NotActive: Port configuration lock key not active
1: Active: Port configuration lock key active

AFRL

GPIO alternate function low register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AFR[EL7] rw				AFR[EL6] rw				AFR[EL5] rw				AFR[EL4] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AFR[EL3] rw				AFR[EL2] rw				AFR[EL1] rw				AFR[EL0] rw

Toggle fields

AFR[EL0]

Bits 0-3: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL1]

Bits 4-7: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL2]

Bits 8-11: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL3]

Bits 12-15: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL4]

Bits 16-19: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL5]

Bits 20-23: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL6]

Bits 24-27: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL7]

Bits 28-31: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFRH

GPIO alternate function high register

Offset: 0x24, size: 32, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AFR[EL15] rw				AFR[EL14] rw				AFR[EL13] rw				AFR[EL12] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AFR[EL11] rw				AFR[EL10] rw				AFR[EL9] rw				AFR[EL8] rw

Toggle fields

AFR[EL8]

Bits 0-3: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL9]

Bits 4-7: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL10]

Bits 8-11: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL11]

Bits 12-15: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL12]

Bits 16-19: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL13]

Bits 20-23: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL14]

Bits 24-27: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

AFR[EL15]

Bits 28-31: Alternate function selection for port x bit y (y = 8..15).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7

BRR

port bit reset register

Offset: 0x28, size: 32, reset: 0x00000000, access: write-only

16/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BR[15] w	BR[14] w	BR[13] w	BR[12] w	BR[11] w	BR[10] w	BR[9] w	BR[8] w	BR[7] w	BR[6] w	BR[5] w	BR[4] w	BR[3] w	BR[2] w	BR[1] w	BR[0] w

Toggle fields

BR[0]

Bit 0: Port x reset pin 0.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[1]

Bit 1: Port x reset pin 1.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[2]

Bit 2: Port x reset pin 2.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[3]

Bit 3: Port x reset pin 3.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[4]

Bit 4: Port x reset pin 4.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[5]

Bit 5: Port x reset pin 5.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[6]

Bit 6: Port x reset pin 6.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[7]

Bit 7: Port x reset pin 7.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[8]

Bit 8: Port x reset pin 8.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[9]

Bit 9: Port x reset pin 9.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[10]

Bit 10: Port x reset pin 10.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[11]

Bit 11: Port x reset pin 11.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[12]

Bit 12: Port x reset pin 12.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[13]

Bit 13: Port x reset pin 13.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[14]

Bit 14: Port x reset pin 14.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR[15]

Bit 15: Port x reset pin 15.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

I2C1

0x40005400: Inter-integrated circuit

76/76 fields covered.

Toggle register map

Offset	Name	31	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	CR1						PECEN	ALERTEN	SMBDEN	SMBHEN	GCEN	WUPEN	NOSTRETCH	SBC	RXDMAEN	TXDMAEN		ANFOFF	DNF				ERRIE	TCIE	STOPIE	NACKIE	ADDRIE	RXIE	TXIE	PE
0x4	CR2			PECBYTE	AUTOEND	RELOAD	NBYTES								NACK	STOP	START	HEAD10R	ADD10	RD_WRN	SADD
0x8	OAR1														OA1EN					OA1MODE	OA1
0xc	OAR2														OA2EN					OA2MSK			OA2
0x10	TIMINGR	PRESC					SCLDEL				SDADEL				SCLH								SCLL
0x14	TIMEOUTR	TEXTEN	TIMEOUTB												TIMOUTEN			TIDLE	TIMEOUTA
0x18	ISR						ADDCODE							DIR	BUSY		ALERT	TIMEOUT	PECERR	OVR	ARLO	BERR	TCR	TC	STOPF	NACKF	ADDR	RXNE	TXIS	TXE
0x1c	ICR																ALERTCF	TIMOUTCF	PECCF	OVRCF	ARLOCF	BERRCF			STOPCF	NACKCF	ADDRCF
0x20	PECR																						PEC
0x24	RXDR																						RXDATA
0x28	TXDR																						TXDATA

Toggle registers

CR1

Control register 1

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

20/20 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								PECEN rw	ALERTEN rw	SMBDEN rw	SMBHEN rw	GCEN rw	WUPEN rw	NOSTRETCH rw	SBC rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RXDMAEN rw	TXDMAEN rw		ANFOFF rw	DNF rw				ERRIE rw	TCIE rw	STOPIE rw	NACKIE rw	ADDRIE rw	RXIE rw	TXIE rw	PE rw

Toggle fields

PE

Bit 0: Peripheral enable.

Allowed values:
0: Disabled: Peripheral disabled
1: Enabled: Peripheral enabled

TXIE

Bit 1: TX Interrupt enable.

Allowed values:
0: Disabled: Transmit (TXIS) interrupt disabled
1: Enabled: Transmit (TXIS) interrupt enabled

RXIE

Bit 2: RX Interrupt enable.

Allowed values:
0: Disabled: Receive (RXNE) interrupt disabled
1: Enabled: Receive (RXNE) interrupt enabled

ADDRIE

Bit 3: Address match interrupt enable (slave only).

Allowed values:
0: Disabled: Address match (ADDR) interrupts disabled
1: Enabled: Address match (ADDR) interrupts enabled

NACKIE

Bit 4: Not acknowledge received interrupt enable.

Allowed values:
0: Disabled: Not acknowledge (NACKF) received interrupts disabled
1: Enabled: Not acknowledge (NACKF) received interrupts enabled

STOPIE

Bit 5: STOP detection Interrupt enable.

Allowed values:
0: Disabled: Stop detection (STOPF) interrupt disabled
1: Enabled: Stop detection (STOPF) interrupt enabled

TCIE

Bit 6: Transfer Complete interrupt enable.

Allowed values:
0: Disabled: Transfer Complete interrupt disabled
1: Enabled: Transfer Complete interrupt enabled

ERRIE

Bit 7: Error interrupts enable.

Allowed values:
0: Disabled: Error detection interrupts disabled
1: Enabled: Error detection interrupts enabled

DNF

Bits 8-11: Digital noise filter.

Allowed values:
0: NoFilter: Digital filter disabled
1: Filter1: Digital filter enabled and filtering capability up to 1 tI2CCLK
2: Filter2: Digital filter enabled and filtering capability up to 2 tI2CCLK
3: Filter3: Digital filter enabled and filtering capability up to 3 tI2CCLK
4: Filter4: Digital filter enabled and filtering capability up to 4 tI2CCLK
5: Filter5: Digital filter enabled and filtering capability up to 5 tI2CCLK
6: Filter6: Digital filter enabled and filtering capability up to 6 tI2CCLK
7: Filter7: Digital filter enabled and filtering capability up to 7 tI2CCLK
8: Filter8: Digital filter enabled and filtering capability up to 8 tI2CCLK
9: Filter9: Digital filter enabled and filtering capability up to 9 tI2CCLK
10: Filter10: Digital filter enabled and filtering capability up to 10 tI2CCLK
11: Filter11: Digital filter enabled and filtering capability up to 11 tI2CCLK
12: Filter12: Digital filter enabled and filtering capability up to 12 tI2CCLK
13: Filter13: Digital filter enabled and filtering capability up to 13 tI2CCLK
14: Filter14: Digital filter enabled and filtering capability up to 14 tI2CCLK
15: Filter15: Digital filter enabled and filtering capability up to 15 tI2CCLK

ANFOFF

Bit 12: Analog noise filter OFF.

Allowed values:
0: Enabled: Analog noise filter enabled
1: Disabled: Analog noise filter disabled

TXDMAEN

Bit 14: DMA transmission requests enable.

Allowed values:
0: Disabled: DMA mode disabled for transmission
1: Enabled: DMA mode enabled for transmission

RXDMAEN

Bit 15: DMA reception requests enable.

Allowed values:
0: Disabled: DMA mode disabled for reception
1: Enabled: DMA mode enabled for reception

SBC

Bit 16: Slave byte control.

Allowed values:
0: Disabled: Slave byte control disabled
1: Enabled: Slave byte control enabled

NOSTRETCH

Bit 17: Clock stretching disable.

Allowed values:
0: Enabled: Clock stretching enabled
1: Disabled: Clock stretching disabled

WUPEN

Bit 18: Wakeup from STOP enable.

Allowed values:
0: Disabled: Wakeup from Stop mode disabled
1: Enabled: Wakeup from Stop mode enabled

GCEN

Bit 19: General call enable.

Allowed values:
0: Disabled: General call disabled. Address 0b00000000 is NACKed
1: Enabled: General call enabled. Address 0b00000000 is ACKed

SMBHEN

Bit 20: SMBus Host address enable.

Allowed values:
0: Disabled: Host address disabled. Address 0b0001000x is NACKed
1: Enabled: Host address enabled. Address 0b0001000x is ACKed

SMBDEN

Bit 21: SMBus Device Default address enable.

Allowed values:
0: Disabled: Device default address disabled. Address 0b1100001x is NACKed
1: Enabled: Device default address enabled. Address 0b1100001x is ACKed

ALERTEN

Bit 22: SMBUS alert enable.

Allowed values:
0: Disabled: In device mode (SMBHEN=Disabled) Releases SMBA pin high and Alert Response Address Header disabled (0001100x) followed by NACK. In host mode (SMBHEN=Enabled) SMBus Alert pin (SMBA) not supported
1: Enabled: In device mode (SMBHEN=Disabled) Drives SMBA pin low and Alert Response Address Header enabled (0001100x) followed by ACK.In host mode (SMBHEN=Enabled) SMBus Alert pin (SMBA) supported

PECEN

Bit 23: PEC enable.

Allowed values:
0: Disabled: PEC calculation disabled
1: Enabled: PEC calculation enabled

CR2

Control register 2

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

11/11 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
					PECBYTE rw	AUTOEND rw	RELOAD rw	NBYTES rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
NACK rw	STOP rw	START rw	HEAD10R rw	ADD10 rw	RD_WRN rw	SADD rw

Toggle fields

SADD

Bits 0-9: Slave address bit (master mode).

Allowed values: 0x0-0x3ff

RD_WRN

Bit 10: Transfer direction (master mode).

Allowed values:
0: Write: Master requests a write transfer
1: Read: Master requests a read transfer

ADD10

Bit 11: 10-bit addressing mode (master mode).

Allowed values:
0: Bit7: The master operates in 7-bit addressing mode
1: Bit10: The master operates in 10-bit addressing mode

HEAD10R

Bit 12: 10-bit address header only read direction (master receiver mode).

Allowed values:
0: Complete: The master sends the complete 10 bit slave address read sequence
1: Partial: The master only sends the 1st 7 bits of the 10 bit address, followed by Read direction

START

Bit 13: Start generation.

Allowed values:
0: NoStart: No Start generation
1: Start: Restart/Start generation

STOP

Bit 14: Stop generation (master mode).

Allowed values:
0: NoStop: No Stop generation
1: Stop: Stop generation after current byte transfer

NACK

Bit 15: NACK generation (slave mode).

Allowed values:
0: Ack: an ACK is sent after current received byte
1: Nack: a NACK is sent after current received byte

NBYTES

Bits 16-23: Number of bytes.

Allowed values: 0x0-0xff

RELOAD

Bit 24: NBYTES reload mode.

Allowed values:
0: Completed: The transfer is completed after the NBYTES data transfer (STOP or RESTART will follow)
1: NotCompleted: The transfer is not completed after the NBYTES data transfer (NBYTES will be reloaded)

AUTOEND

Bit 25: Automatic end mode (master mode).

Allowed values:
0: Software: Software end mode: TC flag is set when NBYTES data are transferred, stretching SCL low
1: Automatic: Automatic end mode: a STOP condition is automatically sent when NBYTES data are transferred

PECBYTE

Bit 26: Packet error checking byte.

Allowed values:
0: NoPec: No PEC transfer
1: Pec: PEC transmission/reception is requested

OAR1

Own address register 1

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

3/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OA1EN rw					OA1MODE rw	OA1 rw

Toggle fields

OA1

Bits 0-9: Interface address.

Allowed values: 0x0-0x3ff

OA1MODE

Bit 10: Own Address 1 10-bit mode.

Allowed values:
0: Bit7: Own address 1 is a 7-bit address
1: Bit10: Own address 1 is a 10-bit address

OA1EN

Bit 15: Own Address 1 enable.

Allowed values:
0: Disabled: Own address 1 disabled. The received slave address OA1 is NACKed
1: Enabled: Own address 1 enabled. The received slave address OA1 is ACKed

OAR2

Own address register 2

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

3/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OA2EN rw					OA2MSK rw			OA2 rw

Toggle fields

OA2

Bits 1-7: Interface address.

Allowed values: 0x0-0x7f

OA2MSK

Bits 8-10: Own Address 2 masks.

Allowed values:
0: NoMask: No mask
1: Mask1: OA2[1] is masked and don’t care. Only OA2[7:2] are compared
2: Mask2: OA2[2:1] are masked and don’t care. Only OA2[7:3] are compared
3: Mask3: OA2[3:1] are masked and don’t care. Only OA2[7:4] are compared
4: Mask4: OA2[4:1] are masked and don’t care. Only OA2[7:5] are compared
5: Mask5: OA2[5:1] are masked and don’t care. Only OA2[7:6] are compared
6: Mask6: OA2[6:1] are masked and don’t care. Only OA2[7] is compared.
7: Mask7: OA2[7:1] are masked and don’t care. No comparison is done, and all (except reserved) 7-bit received addresses are acknowledged

OA2EN

Bit 15: Own Address 2 enable.

Allowed values:
0: Disabled: Own address 2 disabled. The received slave address OA2 is NACKed
1: Enabled: Own address 2 enabled. The received slave address OA2 is ACKed

TIMINGR

Timing register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PRESC rw								SCLDEL rw				SDADEL rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SCLH rw								SCLL rw

Toggle fields

SCLL

Bits 0-7: SCL low period (master mode).

Allowed values: 0x0-0xff

SCLH

Bits 8-15: SCL high period (master mode).

Allowed values: 0x0-0xff

SDADEL

Bits 16-19: Data hold time.

Allowed values: 0x0-0xf

SCLDEL

Bits 20-23: Data setup time.

Allowed values: 0x0-0xf

PRESC

Bits 28-31: Timing prescaler.

Allowed values: 0x0-0xf

TIMEOUTR

Status register 1

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
TEXTEN rw				TIMEOUTB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TIMOUTEN rw			TIDLE rw	TIMEOUTA rw

Toggle fields

TIMEOUTA

Bits 0-11: Bus timeout A.

Allowed values: 0x0-0xfff

TIDLE

Bit 12: Idle clock timeout detection.

Allowed values:
0: Disabled: TIMEOUTA is used to detect SCL low timeout
1: Enabled: TIMEOUTA is used to detect both SCL and SDA high timeout (bus idle condition)

TIMOUTEN

Bit 15: Clock timeout enable.

Allowed values:
0: Disabled: SCL timeout detection is disabled
1: Enabled: SCL timeout detection is enabled

TIMEOUTB

Bits 16-27: Bus timeout B.

Allowed values: 0x0-0xfff

TEXTEN

Bit 31: Extended clock timeout enable.

Allowed values:
0: Disabled: Extended clock timeout detection is disabled
1: Enabled: Extended clock timeout detection is enabled

ISR

Interrupt and Status register

Offset: 0x18, size: 32, reset: 0x00000001, access: Unspecified

17/17 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								ADDCODE r							DIR r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BUSY r		ALERT r	TIMEOUT r	PECERR r	OVR r	ARLO r	BERR r	TCR r	TC r	STOPF r	NACKF r	ADDR r	RXNE r	TXIS rw	TXE rw

Toggle fields

TXE

Bit 0: Transmit data register empty (transmitters).

Allowed values:
0: NotEmpty: TXDR register not empty
1: Empty: TXDR register empty

TXIS

Bit 1: Transmit interrupt status (transmitters).

Allowed values:
0: NotEmpty: The TXDR register is not empty
1: Empty: The TXDR register is empty and the data to be transmitted must be written in the TXDR register

RXNE

Bit 2: Receive data register not empty (receivers).

Allowed values:
0: Empty: The RXDR register is empty
1: NotEmpty: Received data is copied into the RXDR register, and is ready to be read

ADDR

Bit 3: Address matched (slave mode).

Allowed values:
0: NotMatch: Adress mismatched or not received
1: Match: Received slave address matched with one of the enabled slave addresses

NACKF

Bit 4: Not acknowledge received flag.

Allowed values:
0: NoNack: No NACK has been received
1: Nack: NACK has been received

STOPF

Bit 5: Stop detection flag.

Allowed values:
0: NoStop: No Stop condition detected
1: Stop: Stop condition detected

TC

Bit 6: Transfer Complete (master mode).

Allowed values:
0: NotComplete: Transfer is not complete
1: Complete: NBYTES has been transfered

TCR

Bit 7: Transfer Complete Reload.

Allowed values:
0: NotComplete: Transfer is not complete
1: Complete: NBYTES has been transfered

BERR

Bit 8: Bus error.

Allowed values:
0: NoError: No bus error
1: Error: Misplaced Start and Stop condition is detected

ARLO

Bit 9: Arbitration lost.

Allowed values:
0: NotLost: No arbitration lost
1: Lost: Arbitration lost

OVR

Bit 10: Overrun/Underrun (slave mode).

Allowed values:
0: NoOverrun: No overrun/underrun error occurs
1: Overrun: slave mode with NOSTRETCH=1, when an overrun/underrun error occurs

PECERR

Bit 11: PEC Error in reception.

Allowed values:
0: Match: Received PEC does match with PEC register
1: NoMatch: Received PEC does not match with PEC register

TIMEOUT

Bit 12: Timeout or t_low detection flag.

Allowed values:
0: NoTimeout: No timeout occured
1: Timeout: Timeout occured

ALERT

Bit 13: SMBus alert.

Allowed values:
0: NoAlert: SMBA alert is not detected
1: Alert: SMBA alert event is detected on SMBA pin

BUSY

Bit 15: Bus busy.

Allowed values:
0: NotBusy: No communication is in progress on the bus
1: Busy: A communication is in progress on the bus

DIR

Bit 16: Transfer direction (Slave mode).

Allowed values:
0: Write: Write transfer, slave enters receiver mode
1: Read: Read transfer, slave enters transmitter mode

ADDCODE

Bits 17-23: Address match code (Slave mode).

Allowed values: 0x0-0x7f

ICR

Interrupt clear register

Offset: 0x1c, size: 32, reset: 0x00000000, access: write-only

9/9 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		ALERTCF w	TIMOUTCF w	PECCF w	OVRCF w	ARLOCF w	BERRCF w			STOPCF w	NACKCF w	ADDRCF w

Toggle fields

ADDRCF

Bit 3: Address Matched flag clear.

Allowed values:
1: Clear: Clears the ADDR flag in ISR register

NACKCF

Bit 4: Not Acknowledge flag clear.

Allowed values:
1: Clear: Clears the NACK flag in ISR register

STOPCF

Bit 5: Stop detection flag clear.

Allowed values:
1: Clear: Clears the STOP flag in ISR register

BERRCF

Bit 8: Bus error flag clear.

Allowed values:
1: Clear: Clears the BERR flag in ISR register

ARLOCF

Bit 9: Arbitration lost flag clear.

Allowed values:
1: Clear: Clears the ARLO flag in ISR register

OVRCF

Bit 10: Overrun/Underrun flag clear.

Allowed values:
1: Clear: Clears the OVR flag in ISR register

PECCF

Bit 11: PEC Error flag clear.

Allowed values:
1: Clear: Clears the PEC flag in ISR register

TIMOUTCF

Bit 12: Timeout detection flag clear.

Allowed values:
1: Clear: Clears the TIMOUT flag in ISR register

ALERTCF

Bit 13: Alert flag clear.

Allowed values:
1: Clear: Clears the ALERT flag in ISR register

PECR

PEC register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								PEC r

Toggle fields

PEC

Bits 0-7: Packet error checking register.

Allowed values: 0x0-0xff

RXDR

Receive data register

Offset: 0x24, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								RXDATA r

Toggle fields

RXDATA

Bits 0-7: 8-bit receive data.

Allowed values: 0x0-0xff

TXDR

Transmit data register

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								TXDATA rw

Toggle fields

TXDATA

Bits 0-7: 8-bit transmit data.

Allowed values: 0x0-0xff

I2C2

0x40005800: Inter-integrated circuit

76/76 fields covered.

Toggle register map

Offset	Name	31	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	CR1						PECEN	ALERTEN	SMBDEN	SMBHEN	GCEN	WUPEN	NOSTRETCH	SBC	RXDMAEN	TXDMAEN		ANFOFF	DNF				ERRIE	TCIE	STOPIE	NACKIE	ADDRIE	RXIE	TXIE	PE
0x4	CR2			PECBYTE	AUTOEND	RELOAD	NBYTES								NACK	STOP	START	HEAD10R	ADD10	RD_WRN	SADD
0x8	OAR1														OA1EN					OA1MODE	OA1
0xc	OAR2														OA2EN					OA2MSK			OA2
0x10	TIMINGR	PRESC					SCLDEL				SDADEL				SCLH								SCLL
0x14	TIMEOUTR	TEXTEN	TIMEOUTB												TIMOUTEN			TIDLE	TIMEOUTA
0x18	ISR						ADDCODE							DIR	BUSY		ALERT	TIMEOUT	PECERR	OVR	ARLO	BERR	TCR	TC	STOPF	NACKF	ADDR	RXNE	TXIS	TXE
0x1c	ICR																ALERTCF	TIMOUTCF	PECCF	OVRCF	ARLOCF	BERRCF			STOPCF	NACKCF	ADDRCF
0x20	PECR																						PEC
0x24	RXDR																						RXDATA
0x28	TXDR																						TXDATA

Toggle registers

CR1

Control register 1

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

20/20 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								PECEN rw	ALERTEN rw	SMBDEN rw	SMBHEN rw	GCEN rw	WUPEN rw	NOSTRETCH rw	SBC rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RXDMAEN rw	TXDMAEN rw		ANFOFF rw	DNF rw				ERRIE rw	TCIE rw	STOPIE rw	NACKIE rw	ADDRIE rw	RXIE rw	TXIE rw	PE rw

Toggle fields

PE

Bit 0: Peripheral enable.

Allowed values:
0: Disabled: Peripheral disabled
1: Enabled: Peripheral enabled

TXIE

Bit 1: TX Interrupt enable.

Allowed values:
0: Disabled: Transmit (TXIS) interrupt disabled
1: Enabled: Transmit (TXIS) interrupt enabled

RXIE

Bit 2: RX Interrupt enable.

Allowed values:
0: Disabled: Receive (RXNE) interrupt disabled
1: Enabled: Receive (RXNE) interrupt enabled

ADDRIE

Bit 3: Address match interrupt enable (slave only).

Allowed values:
0: Disabled: Address match (ADDR) interrupts disabled
1: Enabled: Address match (ADDR) interrupts enabled

NACKIE

Bit 4: Not acknowledge received interrupt enable.

Allowed values:
0: Disabled: Not acknowledge (NACKF) received interrupts disabled
1: Enabled: Not acknowledge (NACKF) received interrupts enabled

STOPIE

Bit 5: STOP detection Interrupt enable.

Allowed values:
0: Disabled: Stop detection (STOPF) interrupt disabled
1: Enabled: Stop detection (STOPF) interrupt enabled

TCIE

Bit 6: Transfer Complete interrupt enable.

Allowed values:
0: Disabled: Transfer Complete interrupt disabled
1: Enabled: Transfer Complete interrupt enabled

ERRIE

Bit 7: Error interrupts enable.

Allowed values:
0: Disabled: Error detection interrupts disabled
1: Enabled: Error detection interrupts enabled

DNF

Bits 8-11: Digital noise filter.

Allowed values:
0: NoFilter: Digital filter disabled
1: Filter1: Digital filter enabled and filtering capability up to 1 tI2CCLK
2: Filter2: Digital filter enabled and filtering capability up to 2 tI2CCLK
3: Filter3: Digital filter enabled and filtering capability up to 3 tI2CCLK
4: Filter4: Digital filter enabled and filtering capability up to 4 tI2CCLK
5: Filter5: Digital filter enabled and filtering capability up to 5 tI2CCLK
6: Filter6: Digital filter enabled and filtering capability up to 6 tI2CCLK
7: Filter7: Digital filter enabled and filtering capability up to 7 tI2CCLK
8: Filter8: Digital filter enabled and filtering capability up to 8 tI2CCLK
9: Filter9: Digital filter enabled and filtering capability up to 9 tI2CCLK
10: Filter10: Digital filter enabled and filtering capability up to 10 tI2CCLK
11: Filter11: Digital filter enabled and filtering capability up to 11 tI2CCLK
12: Filter12: Digital filter enabled and filtering capability up to 12 tI2CCLK
13: Filter13: Digital filter enabled and filtering capability up to 13 tI2CCLK
14: Filter14: Digital filter enabled and filtering capability up to 14 tI2CCLK
15: Filter15: Digital filter enabled and filtering capability up to 15 tI2CCLK

ANFOFF

Bit 12: Analog noise filter OFF.

Allowed values:
0: Enabled: Analog noise filter enabled
1: Disabled: Analog noise filter disabled

TXDMAEN

Bit 14: DMA transmission requests enable.

Allowed values:
0: Disabled: DMA mode disabled for transmission
1: Enabled: DMA mode enabled for transmission

RXDMAEN

Bit 15: DMA reception requests enable.

Allowed values:
0: Disabled: DMA mode disabled for reception
1: Enabled: DMA mode enabled for reception

SBC

Bit 16: Slave byte control.

Allowed values:
0: Disabled: Slave byte control disabled
1: Enabled: Slave byte control enabled

NOSTRETCH

Bit 17: Clock stretching disable.

Allowed values:
0: Enabled: Clock stretching enabled
1: Disabled: Clock stretching disabled

WUPEN

Bit 18: Wakeup from STOP enable.

Allowed values:
0: Disabled: Wakeup from Stop mode disabled
1: Enabled: Wakeup from Stop mode enabled

GCEN

Bit 19: General call enable.

Allowed values:
0: Disabled: General call disabled. Address 0b00000000 is NACKed
1: Enabled: General call enabled. Address 0b00000000 is ACKed

SMBHEN

Bit 20: SMBus Host address enable.

Allowed values:
0: Disabled: Host address disabled. Address 0b0001000x is NACKed
1: Enabled: Host address enabled. Address 0b0001000x is ACKed

SMBDEN

Bit 21: SMBus Device Default address enable.

Allowed values:
0: Disabled: Device default address disabled. Address 0b1100001x is NACKed
1: Enabled: Device default address enabled. Address 0b1100001x is ACKed

ALERTEN

Bit 22: SMBUS alert enable.

Allowed values:
0: Disabled: In device mode (SMBHEN=Disabled) Releases SMBA pin high and Alert Response Address Header disabled (0001100x) followed by NACK. In host mode (SMBHEN=Enabled) SMBus Alert pin (SMBA) not supported
1: Enabled: In device mode (SMBHEN=Disabled) Drives SMBA pin low and Alert Response Address Header enabled (0001100x) followed by ACK.In host mode (SMBHEN=Enabled) SMBus Alert pin (SMBA) supported

PECEN

Bit 23: PEC enable.

Allowed values:
0: Disabled: PEC calculation disabled
1: Enabled: PEC calculation enabled

CR2

Control register 2

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

11/11 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
					PECBYTE rw	AUTOEND rw	RELOAD rw	NBYTES rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
NACK rw	STOP rw	START rw	HEAD10R rw	ADD10 rw	RD_WRN rw	SADD rw

Toggle fields

SADD

Bits 0-9: Slave address bit (master mode).

Allowed values: 0x0-0x3ff

RD_WRN

Bit 10: Transfer direction (master mode).

Allowed values:
0: Write: Master requests a write transfer
1: Read: Master requests a read transfer

ADD10

Bit 11: 10-bit addressing mode (master mode).

Allowed values:
0: Bit7: The master operates in 7-bit addressing mode
1: Bit10: The master operates in 10-bit addressing mode

HEAD10R

Bit 12: 10-bit address header only read direction (master receiver mode).

Allowed values:
0: Complete: The master sends the complete 10 bit slave address read sequence
1: Partial: The master only sends the 1st 7 bits of the 10 bit address, followed by Read direction

START

Bit 13: Start generation.

Allowed values:
0: NoStart: No Start generation
1: Start: Restart/Start generation

STOP

Bit 14: Stop generation (master mode).

Allowed values:
0: NoStop: No Stop generation
1: Stop: Stop generation after current byte transfer

NACK

Bit 15: NACK generation (slave mode).

Allowed values:
0: Ack: an ACK is sent after current received byte
1: Nack: a NACK is sent after current received byte

NBYTES

Bits 16-23: Number of bytes.

Allowed values: 0x0-0xff

RELOAD

Bit 24: NBYTES reload mode.

Allowed values:
0: Completed: The transfer is completed after the NBYTES data transfer (STOP or RESTART will follow)
1: NotCompleted: The transfer is not completed after the NBYTES data transfer (NBYTES will be reloaded)

AUTOEND

Bit 25: Automatic end mode (master mode).

Allowed values:
0: Software: Software end mode: TC flag is set when NBYTES data are transferred, stretching SCL low
1: Automatic: Automatic end mode: a STOP condition is automatically sent when NBYTES data are transferred

PECBYTE

Bit 26: Packet error checking byte.

Allowed values:
0: NoPec: No PEC transfer
1: Pec: PEC transmission/reception is requested

OAR1

Own address register 1

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

3/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OA1EN rw					OA1MODE rw	OA1 rw

Toggle fields

OA1

Bits 0-9: Interface address.

Allowed values: 0x0-0x3ff

OA1MODE

Bit 10: Own Address 1 10-bit mode.

Allowed values:
0: Bit7: Own address 1 is a 7-bit address
1: Bit10: Own address 1 is a 10-bit address

OA1EN

Bit 15: Own Address 1 enable.

Allowed values:
0: Disabled: Own address 1 disabled. The received slave address OA1 is NACKed
1: Enabled: Own address 1 enabled. The received slave address OA1 is ACKed

OAR2

Own address register 2

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

3/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OA2EN rw					OA2MSK rw			OA2 rw

Toggle fields

OA2

Bits 1-7: Interface address.

Allowed values: 0x0-0x7f

OA2MSK

Bits 8-10: Own Address 2 masks.

Allowed values:
0: NoMask: No mask
1: Mask1: OA2[1] is masked and don’t care. Only OA2[7:2] are compared
2: Mask2: OA2[2:1] are masked and don’t care. Only OA2[7:3] are compared
3: Mask3: OA2[3:1] are masked and don’t care. Only OA2[7:4] are compared
4: Mask4: OA2[4:1] are masked and don’t care. Only OA2[7:5] are compared
5: Mask5: OA2[5:1] are masked and don’t care. Only OA2[7:6] are compared
6: Mask6: OA2[6:1] are masked and don’t care. Only OA2[7] is compared.
7: Mask7: OA2[7:1] are masked and don’t care. No comparison is done, and all (except reserved) 7-bit received addresses are acknowledged

OA2EN

Bit 15: Own Address 2 enable.

Allowed values:
0: Disabled: Own address 2 disabled. The received slave address OA2 is NACKed
1: Enabled: Own address 2 enabled. The received slave address OA2 is ACKed

TIMINGR

Timing register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PRESC rw								SCLDEL rw				SDADEL rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SCLH rw								SCLL rw

Toggle fields

SCLL

Bits 0-7: SCL low period (master mode).

Allowed values: 0x0-0xff

SCLH

Bits 8-15: SCL high period (master mode).

Allowed values: 0x0-0xff

SDADEL

Bits 16-19: Data hold time.

Allowed values: 0x0-0xf

SCLDEL

Bits 20-23: Data setup time.

Allowed values: 0x0-0xf

PRESC

Bits 28-31: Timing prescaler.

Allowed values: 0x0-0xf

TIMEOUTR

Status register 1

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
TEXTEN rw				TIMEOUTB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TIMOUTEN rw			TIDLE rw	TIMEOUTA rw

Toggle fields

TIMEOUTA

Bits 0-11: Bus timeout A.

Allowed values: 0x0-0xfff

TIDLE

Bit 12: Idle clock timeout detection.

Allowed values:
0: Disabled: TIMEOUTA is used to detect SCL low timeout
1: Enabled: TIMEOUTA is used to detect both SCL and SDA high timeout (bus idle condition)

TIMOUTEN

Bit 15: Clock timeout enable.

Allowed values:
0: Disabled: SCL timeout detection is disabled
1: Enabled: SCL timeout detection is enabled

TIMEOUTB

Bits 16-27: Bus timeout B.

Allowed values: 0x0-0xfff

TEXTEN

Bit 31: Extended clock timeout enable.

Allowed values:
0: Disabled: Extended clock timeout detection is disabled
1: Enabled: Extended clock timeout detection is enabled

ISR

Interrupt and Status register

Offset: 0x18, size: 32, reset: 0x00000001, access: Unspecified

17/17 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								ADDCODE r							DIR r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BUSY r		ALERT r	TIMEOUT r	PECERR r	OVR r	ARLO r	BERR r	TCR r	TC r	STOPF r	NACKF r	ADDR r	RXNE r	TXIS rw	TXE rw

Toggle fields

TXE

Bit 0: Transmit data register empty (transmitters).

Allowed values:
0: NotEmpty: TXDR register not empty
1: Empty: TXDR register empty

TXIS

Bit 1: Transmit interrupt status (transmitters).

Allowed values:
0: NotEmpty: The TXDR register is not empty
1: Empty: The TXDR register is empty and the data to be transmitted must be written in the TXDR register

RXNE

Bit 2: Receive data register not empty (receivers).

Allowed values:
0: Empty: The RXDR register is empty
1: NotEmpty: Received data is copied into the RXDR register, and is ready to be read

ADDR

Bit 3: Address matched (slave mode).

Allowed values:
0: NotMatch: Adress mismatched or not received
1: Match: Received slave address matched with one of the enabled slave addresses

NACKF

Bit 4: Not acknowledge received flag.

Allowed values:
0: NoNack: No NACK has been received
1: Nack: NACK has been received

STOPF

Bit 5: Stop detection flag.

Allowed values:
0: NoStop: No Stop condition detected
1: Stop: Stop condition detected

TC

Bit 6: Transfer Complete (master mode).

Allowed values:
0: NotComplete: Transfer is not complete
1: Complete: NBYTES has been transfered

TCR

Bit 7: Transfer Complete Reload.

Allowed values:
0: NotComplete: Transfer is not complete
1: Complete: NBYTES has been transfered

BERR

Bit 8: Bus error.

Allowed values:
0: NoError: No bus error
1: Error: Misplaced Start and Stop condition is detected

ARLO

Bit 9: Arbitration lost.

Allowed values:
0: NotLost: No arbitration lost
1: Lost: Arbitration lost

OVR

Bit 10: Overrun/Underrun (slave mode).

Allowed values:
0: NoOverrun: No overrun/underrun error occurs
1: Overrun: slave mode with NOSTRETCH=1, when an overrun/underrun error occurs

PECERR

Bit 11: PEC Error in reception.

Allowed values:
0: Match: Received PEC does match with PEC register
1: NoMatch: Received PEC does not match with PEC register

TIMEOUT

Bit 12: Timeout or t_low detection flag.

Allowed values:
0: NoTimeout: No timeout occured
1: Timeout: Timeout occured

ALERT

Bit 13: SMBus alert.

Allowed values:
0: NoAlert: SMBA alert is not detected
1: Alert: SMBA alert event is detected on SMBA pin

BUSY

Bit 15: Bus busy.

Allowed values:
0: NotBusy: No communication is in progress on the bus
1: Busy: A communication is in progress on the bus

DIR

Bit 16: Transfer direction (Slave mode).

Allowed values:
0: Write: Write transfer, slave enters receiver mode
1: Read: Read transfer, slave enters transmitter mode

ADDCODE

Bits 17-23: Address match code (Slave mode).

Allowed values: 0x0-0x7f

ICR

Interrupt clear register

Offset: 0x1c, size: 32, reset: 0x00000000, access: write-only

9/9 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		ALERTCF w	TIMOUTCF w	PECCF w	OVRCF w	ARLOCF w	BERRCF w			STOPCF w	NACKCF w	ADDRCF w

Toggle fields

ADDRCF

Bit 3: Address Matched flag clear.

Allowed values:
1: Clear: Clears the ADDR flag in ISR register

NACKCF

Bit 4: Not Acknowledge flag clear.

Allowed values:
1: Clear: Clears the NACK flag in ISR register

STOPCF

Bit 5: Stop detection flag clear.

Allowed values:
1: Clear: Clears the STOP flag in ISR register

BERRCF

Bit 8: Bus error flag clear.

Allowed values:
1: Clear: Clears the BERR flag in ISR register

ARLOCF

Bit 9: Arbitration lost flag clear.

Allowed values:
1: Clear: Clears the ARLO flag in ISR register

OVRCF

Bit 10: Overrun/Underrun flag clear.

Allowed values:
1: Clear: Clears the OVR flag in ISR register

PECCF

Bit 11: PEC Error flag clear.

Allowed values:
1: Clear: Clears the PEC flag in ISR register

TIMOUTCF

Bit 12: Timeout detection flag clear.

Allowed values:
1: Clear: Clears the TIMOUT flag in ISR register

ALERTCF

Bit 13: Alert flag clear.

Allowed values:
1: Clear: Clears the ALERT flag in ISR register

PECR

PEC register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								PEC r

Toggle fields

PEC

Bits 0-7: Packet error checking register.

Allowed values: 0x0-0xff

RXDR

Receive data register

Offset: 0x24, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								RXDATA r

Toggle fields

RXDATA

Bits 0-7: 8-bit receive data.

Allowed values: 0x0-0xff

TXDR

Transmit data register

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								TXDATA rw

Toggle fields

TXDATA

Bits 0-7: 8-bit transmit data.

Allowed values: 0x0-0xff

IWDG

0x40003000: Independent watchdog

7/7 fields covered.

Toggle register map

Offset	Name	15	11	2	1	0
0x0	KR	KEY
0x4	PR			PR
0x8	RLR		RL
0xc	SR			WVU	RVU	PVU
0x10	WINR		WIN

Toggle registers

KR

Key register

Offset: 0x0, size: 32, reset: 0x00000000, access: write-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
KEY w

Toggle fields

KEY

Bits 0-15: Key value (write only, read 0x0000).

Allowed values:
21845: Unlock: Enable access to PR, RLR and WINR registers
43690: Feed: Feed watchdog with RLR register value
52428: Start: Start the watchdog

PR

Prescaler register

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
													PR rw

Toggle fields

PR

Bits 0-2: Prescaler divider.

Allowed values:
0: DivideBy4: Divider /4
1: DivideBy8: Divider /8
2: DivideBy16: Divider /16
3: DivideBy32: Divider /32
4: DivideBy64: Divider /64
5: DivideBy128: Divider /128
6: DivideBy256: Divider /256

RLR

Reload register

Offset: 0x8, size: 32, reset: 0x00000FFF, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				RL rw

Toggle fields

RL

Bits 0-11: Watchdog counter reload value.

Allowed values: 0x0-0xfff

SR

Status register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-only

3/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
													WVU r	RVU r	PVU r

Toggle fields

PVU

Bit 0: Watchdog prescaler value update.

RVU

Bit 1: Watchdog counter reload value update.

WVU

Bit 2: Watchdog counter window value update.

WINR

Window register

Offset: 0x10, size: 32, reset: 0x00000FFF, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				WIN rw

Toggle fields

WIN

Bits 0-11: Watchdog counter window value.

Allowed values: 0x0-0xfff

LPTIM1

0x40007c00: Low power timer

8/44 fields covered.

Toggle register map

Offset	Name	24	23	22	21	20	19	18	15	11	7	6	5	4	3	2	1	0
0x0	ISR											DOWN	UP	ARROK	CMPOK	EXTTRIG	ARRM	CMPM
0x4	ICR											DOWNCF	UPCF	ARROKCF	CMPOKCF	EXTTRIGCF	ARRMCF	CMPMCF
0x8	IER											DOWNIE	UPIE	ARROKIE	CMPOKIE	EXTTRIGIE	ARRMIE	CMPMIE
0xc	CFGR	ENC	COUNTMODE	PRELOAD	WAVPOL	WAVE	TIMOUT	TRIGEN	TRIGSEL	PRESC	TRGFLT			CKFLT		CKPOL		CKSEL
0x10	CR													RSTARE	COUNTRST	CNTSTRT	SNGSTRT	ENABLE
0x14	CMP								CMP
0x18	ARR								ARR
0x1c	CNT								CNT
0x24	CFGR2												IN2SEL				IN1SEL

Toggle registers

ISR

Interrupt and Status Register

Offset: 0x0, size: 32, reset: 0x00000000, access: read-only

7/7 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
									DOWN r	UP r	ARROK r	CMPOK r	EXTTRIG r	ARRM r	CMPM r

Toggle fields

CMPM

Bit 0: Compare match.

ARRM

Bit 1: Autoreload match.

EXTTRIG

Bit 2: External trigger edge event.

CMPOK

Bit 3: Compare register update OK.

ARROK

Bit 4: Autoreload register update OK.

UP

Bit 5: Counter direction change down to up.

DOWN

Bit 6: Counter direction change up to down.

ICR

Interrupt Clear Register

Offset: 0x4, size: 32, reset: 0x00000000, access: write-only

0/7 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
									DOWNCF w	UPCF w	ARROKCF w	CMPOKCF w	EXTTRIGCF w	ARRMCF w	CMPMCF w

Toggle fields

CMPMCF

Bit 0: compare match Clear Flag.

ARRMCF

Bit 1: Autoreload match Clear Flag.

EXTTRIGCF

Bit 2: External trigger valid edge Clear Flag.

CMPOKCF

Bit 3: Compare register update OK Clear Flag.

ARROKCF

Bit 4: Autoreload register update OK Clear Flag.

UPCF

Bit 5: Direction change to UP Clear Flag.

DOWNCF

Bit 6: Direction change to down Clear Flag.

IER

Interrupt Enable Register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

0/7 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
									DOWNIE rw	UPIE rw	ARROKIE rw	CMPOKIE rw	EXTTRIGIE rw	ARRMIE rw	CMPMIE rw

Toggle fields

CMPMIE

Bit 0: Compare match Interrupt Enable.

ARRMIE

Bit 1: Autoreload match Interrupt Enable.

EXTTRIGIE

Bit 2: External trigger valid edge Interrupt Enable.

CMPOKIE

Bit 3: Compare register update OK Interrupt Enable.

ARROKIE

Bit 4: Autoreload register update OK Interrupt Enable.

UPIE

Bit 5: Direction change to UP Interrupt Enable.

DOWNIE

Bit 6: Direction change to down Interrupt Enable.

CFGR

Configuration Register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

0/13 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
							ENC rw	COUNTMODE rw	PRELOAD rw	WAVPOL rw	WAVE rw	TIMOUT rw	TRIGEN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TRIGSEL rw				PRESC rw				TRGFLT rw			CKFLT rw		CKPOL rw		CKSEL rw

Toggle fields

CKSEL

Bit 0: Clock selector.

CKPOL

Bits 1-2: Clock Polarity.

CKFLT

Bits 3-4: Configurable digital filter for external clock.

TRGFLT

Bits 6-7: Configurable digital filter for trigger.

PRESC

Bits 9-11: Clock prescaler.

TRIGSEL

Bits 13-15: Trigger selector.

TRIGEN

Bits 17-18: Trigger enable and polarity.

TIMOUT

Bit 19: Timeout enable.

WAVE

Bit 20: Waveform shape.

WAVPOL

Bit 21: Waveform shape polarity.

PRELOAD

Bit 22: Registers update mode.

COUNTMODE

Bit 23: counter mode enabled.

ENC

Bit 24: Encoder mode enable.

CR

Control Register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

0/5 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
											RSTARE rw	COUNTRST rw	CNTSTRT rw	SNGSTRT rw	ENABLE rw

Toggle fields

ENABLE

Bit 0: LPTIM Enable.

SNGSTRT

Bit 1: LPTIM start in single mode.

CNTSTRT

Bit 2: Timer start in continuous mode.

COUNTRST

Bit 3: Counter reset.

RSTARE

Bit 4: Reset after read enable.

CMP

Compare Register

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CMP rw

Toggle fields

CMP

Bits 0-15: Compare value.

ARR

Autoreload Register

Offset: 0x18, size: 32, reset: 0x00000001, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ARR rw

Toggle fields

ARR

Bits 0-15: Auto reload value.

CNT

Counter Register

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CNT r

Toggle fields

CNT

Bits 0-15: Counter value.

CFGR2

LPTIM configuration register 2

Offset: 0x24, size: 32, reset: 0x00000000, access: read-write

0/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
										IN2SEL rw				IN1SEL rw

Toggle fields

IN1SEL

Bits 0-1: LPTIMx Input 1 selection.

IN2SEL

Bits 4-5: LPTIM1 Input 2 selection.

LPTIM2

0x40009400: Low power timer

8/44 fields covered.

Toggle register map

Offset	Name	24	23	22	21	20	19	18	15	11	7	6	5	4	3	2	1	0
0x0	ISR											DOWN	UP	ARROK	CMPOK	EXTTRIG	ARRM	CMPM
0x4	ICR											DOWNCF	UPCF	ARROKCF	CMPOKCF	EXTTRIGCF	ARRMCF	CMPMCF
0x8	IER											DOWNIE	UPIE	ARROKIE	CMPOKIE	EXTTRIGIE	ARRMIE	CMPMIE
0xc	CFGR	ENC	COUNTMODE	PRELOAD	WAVPOL	WAVE	TIMOUT	TRIGEN	TRIGSEL	PRESC	TRGFLT			CKFLT		CKPOL		CKSEL
0x10	CR													RSTARE	COUNTRST	CNTSTRT	SNGSTRT	ENABLE
0x14	CMP								CMP
0x18	ARR								ARR
0x1c	CNT								CNT
0x24	CFGR2												IN2SEL				IN1SEL

Toggle registers

ISR

Interrupt and Status Register

Offset: 0x0, size: 32, reset: 0x00000000, access: read-only

7/7 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
									DOWN r	UP r	ARROK r	CMPOK r	EXTTRIG r	ARRM r	CMPM r

Toggle fields

CMPM

Bit 0: Compare match.

ARRM

Bit 1: Autoreload match.

EXTTRIG

Bit 2: External trigger edge event.

CMPOK

Bit 3: Compare register update OK.

ARROK

Bit 4: Autoreload register update OK.

UP

Bit 5: Counter direction change down to up.

DOWN

Bit 6: Counter direction change up to down.

ICR

Interrupt Clear Register

Offset: 0x4, size: 32, reset: 0x00000000, access: write-only

0/7 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
									DOWNCF w	UPCF w	ARROKCF w	CMPOKCF w	EXTTRIGCF w	ARRMCF w	CMPMCF w

Toggle fields

CMPMCF

Bit 0: compare match Clear Flag.

ARRMCF

Bit 1: Autoreload match Clear Flag.

EXTTRIGCF

Bit 2: External trigger valid edge Clear Flag.

CMPOKCF

Bit 3: Compare register update OK Clear Flag.

ARROKCF

Bit 4: Autoreload register update OK Clear Flag.

UPCF

Bit 5: Direction change to UP Clear Flag.

DOWNCF

Bit 6: Direction change to down Clear Flag.

IER

Interrupt Enable Register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

0/7 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
									DOWNIE rw	UPIE rw	ARROKIE rw	CMPOKIE rw	EXTTRIGIE rw	ARRMIE rw	CMPMIE rw

Toggle fields

CMPMIE

Bit 0: Compare match Interrupt Enable.

ARRMIE

Bit 1: Autoreload match Interrupt Enable.

EXTTRIGIE

Bit 2: External trigger valid edge Interrupt Enable.

CMPOKIE

Bit 3: Compare register update OK Interrupt Enable.

ARROKIE

Bit 4: Autoreload register update OK Interrupt Enable.

UPIE

Bit 5: Direction change to UP Interrupt Enable.

DOWNIE

Bit 6: Direction change to down Interrupt Enable.

CFGR

Configuration Register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

0/13 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
							ENC rw	COUNTMODE rw	PRELOAD rw	WAVPOL rw	WAVE rw	TIMOUT rw	TRIGEN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TRIGSEL rw				PRESC rw				TRGFLT rw			CKFLT rw		CKPOL rw		CKSEL rw

Toggle fields

CKSEL

Bit 0: Clock selector.

CKPOL

Bits 1-2: Clock Polarity.

CKFLT

Bits 3-4: Configurable digital filter for external clock.

TRGFLT

Bits 6-7: Configurable digital filter for trigger.

PRESC

Bits 9-11: Clock prescaler.

TRIGSEL

Bits 13-15: Trigger selector.

TRIGEN

Bits 17-18: Trigger enable and polarity.

TIMOUT

Bit 19: Timeout enable.

WAVE

Bit 20: Waveform shape.

WAVPOL

Bit 21: Waveform shape polarity.

PRELOAD

Bit 22: Registers update mode.

COUNTMODE

Bit 23: counter mode enabled.

ENC

Bit 24: Encoder mode enable.

CR

Control Register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

0/5 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
											RSTARE rw	COUNTRST rw	CNTSTRT rw	SNGSTRT rw	ENABLE rw

Toggle fields

ENABLE

Bit 0: LPTIM Enable.

SNGSTRT

Bit 1: LPTIM start in single mode.

CNTSTRT

Bit 2: Timer start in continuous mode.

COUNTRST

Bit 3: Counter reset.

RSTARE

Bit 4: Reset after read enable.

CMP

Compare Register

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CMP rw

Toggle fields

CMP

Bits 0-15: Compare value.

ARR

Autoreload Register

Offset: 0x18, size: 32, reset: 0x00000001, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ARR rw

Toggle fields

ARR

Bits 0-15: Auto reload value.

CNT

Counter Register

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CNT r

Toggle fields

CNT

Bits 0-15: Counter value.

CFGR2

LPTIM configuration register 2

Offset: 0x24, size: 32, reset: 0x00000000, access: read-write

0/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
										IN2SEL rw				IN1SEL rw

Toggle fields

IN1SEL

Bits 0-1: LPTIMx Input 1 selection.

IN2SEL

Bits 4-5: LPTIM1 Input 2 selection.

LPUART

0x40008000: Universal synchronous asynchronous receiver transmitter

22/86 fields covered.

Toggle register map

Offset	Name	31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	CR1	RXFFIE	TXFEIE	FIFOEN	M1			DEAT					DEDT0						CMIE	MME	M0	WAKE	PCE	PS	PEIE	TXEIE	TCIE	RXNEIE	IDLEIE	TE	RE	UESM	UE
0x4	CR2	ADD4_7				ADD0_3								MSBFIRST	TAINV	TXINV	RXINV	SWAP		STOP									ADDM7
0x8	CR3	TXFTCFG			RXFTIE	RXFTCFG				TXFTIE	WUFIE	WUS						DEP	DEM	DDRE	OVRDIS		CTSIE	CTSE	RTSE	DMAT	DMAR			HDSEL			EIE
0xc	BRR													BRR				BRR
0x18	RQR																												TXFRQ	RXFRQ	MMRQ	SBKRQ	ABRRQ
0x1c	ISR					TXFT	RXFT		RXFF	TXFE	REACK	TEACK	WUF	RWU	SBKF	CMF	BUSY						CTS	CTSIF		TXE	TC	RXNE	IDLE	ORE	NF	FE	PE
0x20	ICR												WUCF			CMCF								CTSCF			TCCF		IDLECF	ORECF	NCF	FECF	PECF
0x24	RDR																								RDR
0x28	TDR																								TDR
0x2c	PRESC																													PRESCALER

Toggle registers

CR1

Control register 1

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

0/21 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
RXFFIE rw	TXFEIE rw	FIFOEN rw	M1 rw			DEAT rw					DEDT0 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	CMIE rw	MME rw	M0 rw	WAKE rw	PCE rw	PS rw	PEIE rw	TXEIE rw	TCIE rw	RXNEIE rw	IDLEIE rw	TE rw	RE rw	UESM rw	UE rw

Toggle fields

UE

Bit 0: USART enable.

UESM

Bit 1: USART enable in Stop mode.

RE

Bit 2: Receiver enable.

TE

Bit 3: Transmitter enable.

IDLEIE

Bit 4: IDLE interrupt enable.

RXNEIE

Bit 5: RXNE interrupt enable.

TCIE

Bit 6: Transmission complete interrupt enable.

TXEIE

Bit 7: interrupt enable.

PEIE

Bit 8: PE interrupt enable.

PS

Bit 9: Parity selection.

PCE

Bit 10: Parity control enable.

WAKE

Bit 11: Receiver wakeup method.

M0

Bit 12: Word length.

MME

Bit 13: Mute mode enable.

CMIE

Bit 14: Character match interrupt enable.

DEDT0

Bits 16-20: DEDT0.

DEAT

Bits 21-25: DEAT0.

M1

Bit 28: Word length.

FIFOEN

Bit 29: FIFO mode enable.

TXFEIE

Bit 30: TXFIFO empty interrupt enable.

RXFFIE

Bit 31: RXFIFO Full interrupt enable.

CR2

Control register 2

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

0/9 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ADD4_7 rw				ADD0_3 rw								MSBFIRST rw	TAINV rw	TXINV rw	RXINV rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SWAP rw		STOP rw									ADDM7 rw

Toggle fields

ADDM7

Bit 4: 7-bit Address Detection/4-bit Address Detection.

STOP

Bits 12-13: STOP bits.

SWAP

Bit 15: Swap TX/RX pins.

RXINV

Bit 16: RX pin active level inversion.

TXINV

Bit 17: TX pin active level inversion.

TAINV

Bit 18: Binary data inversion.

MSBFIRST

Bit 19: Most significant bit first.

ADD0_3

Bits 24-27: Address of the USART node.

ADD4_7

Bits 28-31: Address of the USART node.

CR3

Control register 3

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

0/17 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
TXFTCFG rw			RXFTIE rw	RXFTCFG rw				TXFTIE rw	WUFIE rw	WUS rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DEP rw	DEM rw	DDRE rw	OVRDIS rw		CTSIE rw	CTSE rw	RTSE rw	DMAT rw	DMAR rw			HDSEL rw			EIE rw

Toggle fields

EIE

Bit 0: Error interrupt enable.

HDSEL

Bit 3: Half-duplex selection.

DMAR

Bit 6: DMA enable receiver.

DMAT

Bit 7: DMA enable transmitter.

RTSE

Bit 8: RTS enable.

CTSE

Bit 9: CTS enable.

CTSIE

Bit 10: CTS interrupt enable.

OVRDIS

Bit 12: Overrun Disable.

DDRE

Bit 13: DMA Disable on Reception Error.

DEM

Bit 14: Driver enable mode.

DEP

Bit 15: Driver enable polarity selection.

WUS

Bits 20-21: Wakeup from Stop mode interrupt flag selection.

WUFIE

Bit 22: Wakeup from Stop mode interrupt enable.

TXFTIE

Bit 23: threshold interrupt enable.

RXFTCFG

Bits 25-27: Receive FIFO threshold configuration.

RXFTIE

Bit 28: RXFIFO threshold interrupt enable.

TXFTCFG

Bits 29-31: TXFIFO threshold configuration.

BRR

Baud rate register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
												BRR rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BRR rw

Toggle fields

BRR

Bits 0-19: BRR.

RQR

Request register

Offset: 0x18, size: 32, reset: 0x00000000, access: write-only

0/5 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
											TXFRQ w	RXFRQ w	MMRQ w	SBKRQ w	ABRRQ w

Toggle fields

ABRRQ

Bit 0: Auto baud rate request.

SBKRQ

Bit 1: Send break request.

MMRQ

Bit 2: Mute mode request.

RXFRQ

Bit 3: Receive data flush request.

TXFRQ

Bit 4: Transmit data flush request.

ISR

Interrupt & status register

Offset: 0x1c, size: 32, reset: 0x000000C0, access: read-only

21/21 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				TXFT r	RXFT r		RXFF r	TXFE r	REACK r	TEACK r	WUF r	RWU r	SBKF r	CMF r	BUSY r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
					CTS r	CTSIF r		TXE r	TC r	RXNE r	IDLE r	ORE r	NF r	FE r	PE r

Toggle fields

PE

Bit 0: PE.

FE

Bit 1: FE.

NF

Bit 2: NF.

ORE

Bit 3: ORE.

IDLE

Bit 4: IDLE.

RXNE

Bit 5: RXNE.

TC

Bit 6: TC.

TXE

Bit 7: TXE.

CTSIF

Bit 9: CTSIF.

CTS

Bit 10: CTS.

BUSY

Bit 16: BUSY.

CMF

Bit 17: CMF.

SBKF

Bit 18: SBKF.

RWU

Bit 19: RWU.

WUF

Bit 20: WUF.

TEACK

Bit 21: TEACK.

REACK

Bit 22: REACK.

TXFE

Bit 23: TXFIFO Empty.

RXFF

Bit 24: RXFIFO Full.

RXFT

Bit 26: RXFIFO threshold flag.

TXFT

Bit 27: TXFIFO threshold flag.

ICR

Interrupt flag clear register

Offset: 0x20, size: 32, reset: 0x00000000, access: write-only

0/9 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
											WUCF w			CMCF w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						CTSCF w			TCCF w		IDLECF w	ORECF w	NCF w	FECF w	PECF w

Toggle fields

PECF

Bit 0: Parity error clear flag.

FECF

Bit 1: Framing error clear flag.

NCF

Bit 2: Noise detected clear flag.

ORECF

Bit 3: Overrun error clear flag.

IDLECF

Bit 4: Idle line detected clear flag.

TCCF

Bit 6: Transmission complete clear flag.

CTSCF

Bit 9: CTS clear flag.

CMCF

Bit 17: Character match clear flag.

WUCF

Bit 20: Wakeup from Stop mode clear flag.

RDR

Receive data register

Offset: 0x24, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							RDR r

Toggle fields

RDR

Bits 0-8: Receive data value.

TDR

Transmit data register

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							TDR rw

Toggle fields

TDR

Bits 0-8: Transmit data value.

PRESC

Prescaler register

Offset: 0x2c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
												PRESCALER rw

Toggle fields

PRESCALER

Bits 0-3: Clock prescaler.

PWR

0x40007000: Power control

15/242 fields covered.

Toggle register map

Offset	Name	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	CR1		LPR				VOS		DBP			FPD_LPSLP	FPD_LPRUN	FPD_STOP	LPMS
0x4	CR2						USV	IOSV	PVMENUSB	PVMENDAC	PVDRT			PVDFT			PVDE
0x8	CR3	EIWUL					APC	ENB_ULP	RRS			EWUP6	EWUP5	EWUP4	EWUP3	EWUP2	EWUP1
0xc	CR4							VBRS	VBE			WP6	WP5	WP4	WP3	WP2	WP1
0x10	SR1	WUFI							SBF			WUF6	WUF5	WUF4	WUF3	WUF2	WUF1
0x14	SR2	PVMODAC			PVMOUSB	PVDO	VOSF	REGLPF	REGLPS	FLASH_RDY
0x18	SCR								CSBF			CWUF6	CWUF5	CWUF4	CWUF3	CWUF2	CWUF1
0x20	PUCRA	PU15	PU14	PU13	PU12	PU11	PU10	PU9	PU8	PU7	PU6	PU5	PU4	PU3	PU2	PU1	PU0
0x24	PDCRA	PD15	PD14	PD13	PD12	PD11	PD10	PD9	PD8	PD7	PD6	PD5	PD4	PD3	PD2	PD1	PD0
0x28	PUCRB	PU15	PU14	PU13	PU12	PU11	PU10	PU9	PU8	PU7	PU6	PU5	PU4	PU3	PU2	PU1	PU0
0x2c	PDCRB	PD15	PD14	PD13	PD12	PD11	PD10	PD9	PD8	PD7	PD6	PD5	PD4	PD3	PD2	PD1	PD0
0x30	PUCRC	PU15	PU14	PU13	PU12	PU11	PU10	PU9	PU8	PU7	PU6	PU5	PU4	PU3	PU2	PU1	PU0
0x34	PDCRC	PD15	PD14	PD13	PD12	PD11	PD10	PD9	PD8	PD7	PD6	PD5	PD4	PD3	PD2	PD1	PD0
0x38	PUCRD	PU15	PU14	PU13	PU12	PU11	PU10	PU9	PU8	PU7	PU6	PU5	PU4	PU3	PU2	PU1	PU0
0x3c	PDCRD	PD15	PD14	PD13	PD12	PD11	PD10	PD9	PD8	PD7	PD6	PD5	PD4	PD3	PD2	PD1	PD0
0x40	PUCRE	PU15	PU14	PU13	PU12	PU11	PU10	PU9	PU8	PU7	PU6	PU5	PU4	PU3	PU2	PU1	PU0
0x44	PDCRE	PD15	PD14	PD13	PD12	PD11	PD10	PD9	PD8	PD7	PD6	PD5	PD4	PD3	PD2	PD1	PD0
0x48	PUCRF			PU13	PU12	PU11	PU10	PU9	PU8	PU7	PU6	PU5	PU4	PU3	PU2	PU1	PU0
0x4c	PDCRF			PD13	PD12	PD11	PD10	PD9	PD8	PD7	PD6	PD5	PD4	PD3	PD2	PD1	PD0

Toggle registers

CR1

Power control register 1

Offset: 0x0, size: 32, reset: 0x00000208, access: read-write

0/7 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	LPR rw				VOS rw		DBP rw			FPD_LPSLP rw	FPD_LPRUN rw	FPD_STOP rw	LPMS rw

Toggle fields

LPMS

Bits 0-2: Low-power mode selection.

FPD_STOP

Bit 3: Flash memory powered down during Stop mode.

FPD_LPRUN

Bit 4: Flash memory powered down during Low-power run mode.

FPD_LPSLP

Bit 5: Flash memory powered down during Low-power sleep mode.

DBP

Bit 8: Disable backup domain write protection.

VOS

Bits 9-10: Voltage scaling range selection.

LPR

Bit 14: Low-power run.

CR2

Power control register 2

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

0/7 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
					USV rw	IOSV rw	PVMENUSB rw	PVMENDAC rw	PVDRT rw			PVDFT rw			PVDE rw

Toggle fields

PVDE

Bit 0: Power voltage detector enable.

PVDFT

Bits 1-3: Power voltage detector falling threshold selection.

PVDRT

Bits 4-6: Power voltage detector rising threshold selection.

PVMENDAC

Bit 7: PVMENDAC.

PVMENUSB

Bit 8: PVMENUSB.

IOSV

Bit 9: IOSV.

USV

Bit 10: USV.

CR3

Power control register 3

Offset: 0x8, size: 32, reset: 0x00008000, access: read-write

0/10 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
EIWUL rw					APC rw	ENB_ULP rw	RRS rw			EWUP6 rw	EWUP5 rw	EWUP4 rw	EWUP3 rw	EWUP2 rw	EWUP1 rw

Toggle fields

EWUP1

Bit 0: Enable Wakeup pin WKUP1.

EWUP2

Bit 1: Enable Wakeup pin WKUP2.

EWUP3

Bit 2: Enable Wakeup pin WKUP3.

EWUP4

Bit 3: Enable Wakeup pin WKUP4.

EWUP5

Bit 4: Enable WKUP5 wakeup pin.

EWUP6

Bit 5: Enable WKUP6 wakeup pin.

RRS

Bit 8: SRAM retention in Standby mode.

ENB_ULP

Bit 9: Ultra-low-power enable.

APC

Bit 10: Apply pull-up and pull-down configuration.

EIWUL

Bit 15: Enable internal wakeup line.

CR4

Power control register 4

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

0/8 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						VBRS rw	VBE rw			WP6 rw	WP5 rw	WP4 rw	WP3 rw	WP2 rw	WP1 rw

Toggle fields

WP1

Bit 0: Wakeup pin WKUP1 polarity.

WP2

Bit 1: Wakeup pin WKUP2 polarity.

WP3

Bit 2: Wakeup pin WKUP3 polarity.

WP4

Bit 3: Wakeup pin WKUP4 polarity.

WP5

Bit 4: Wakeup pin WKUP5 polarity.

WP6

Bit 5: WKUP6 wakeup pin polarity.

VBE

Bit 8: VBAT battery charging enable.

VBRS

Bit 9: VBAT battery charging resistor selection.

SR1

Power status register 1

Offset: 0x10, size: 32, reset: 0x00000000, access: read-only

8/8 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
WUFI r							SBF r			WUF6 r	WUF5 r	WUF4 r	WUF3 r	WUF2 r	WUF1 r

Toggle fields

WUF1

Bit 0: Wakeup flag 1.

WUF2

Bit 1: Wakeup flag 2.

WUF3

Bit 2: Wakeup flag 3.

WUF4

Bit 3: Wakeup flag 4.

WUF5

Bit 4: Wakeup flag 5.

WUF6

Bit 5: Wakeup flag 6.

SBF

Bit 8: Standby flag.

WUFI

Bit 15: Wakeup flag internal.

SR2

Power status register 2

Offset: 0x14, size: 32, reset: 0x00000000, access: read-only

7/7 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PVMODAC r			PVMOUSB r	PVDO r	VOSF r	REGLPF r	REGLPS r	FLASH_RDY r

Toggle fields

FLASH_RDY

Bit 7: Flash ready flag.

REGLPS

Bit 8: Low-power regulator started.

REGLPF

Bit 9: Low-power regulator flag.

VOSF

Bit 10: Voltage scaling flag.

PVDO

Bit 11: Power voltage detector output.

PVMOUSB

Bit 12: USB supply voltage monitoring output flag.

PVMODAC

Bit 15: VDDA monitoring output flag.

SCR

Power status clear register

Offset: 0x18, size: 32, reset: 0x00000000, access: write-only

0/7 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							CSBF w			CWUF6 w	CWUF5 w	CWUF4 w	CWUF3 w	CWUF2 w	CWUF1 w

Toggle fields

CWUF1

Bit 0: Clear wakeup flag 1.

CWUF2

Bit 1: Clear wakeup flag 2.

CWUF3

Bit 2: Clear wakeup flag 3.

CWUF4

Bit 3: Clear wakeup flag 4.

CWUF5

Bit 4: Clear wakeup flag 5.

CWUF6

Bit 5: Clear wakeup flag 6.

CSBF

Bit 8: Clear standby flag.

PUCRA

Power Port A pull-up control register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

0/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PU15 rw	PU14 rw	PU13 rw	PU12 rw	PU11 rw	PU10 rw	PU9 rw	PU8 rw	PU7 rw	PU6 rw	PU5 rw	PU4 rw	PU3 rw	PU2 rw	PU1 rw	PU0 rw

Toggle fields

PU0

Bit 0: Port A pull-up bit y (y=0..15).

PU1

Bit 1: Port A pull-up bit y (y=0..15).

PU2

Bit 2: Port A pull-up bit y (y=0..15).

PU3

Bit 3: Port A pull-up bit y (y=0..15).

PU4

Bit 4: Port A pull-up bit y (y=0..15).

PU5

Bit 5: Port A pull-up bit y (y=0..15).

PU6

Bit 6: Port A pull-up bit y (y=0..15).

PU7

Bit 7: Port A pull-up bit y (y=0..15).

PU8

Bit 8: Port A pull-up bit y (y=0..15).

PU9

Bit 9: Port A pull-up bit y (y=0..15).

PU10

Bit 10: Port A pull-up bit y (y=0..15).

PU11

Bit 11: Port A pull-up bit y (y=0..15).

PU12

Bit 12: Port A pull-up bit y (y=0..15).

PU13

Bit 13: Port A pull-up bit y (y=0..15).

PU14

Bit 14: Port A pull-up bit y (y=0..15).

PU15

Bit 15: Port A pull-up bit y (y=0..15).

PDCRA

Power Port A pull-down control register

Offset: 0x24, size: 32, reset: 0x00000000, access: read-write

0/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PD15 rw	PD14 rw	PD13 rw	PD12 rw	PD11 rw	PD10 rw	PD9 rw	PD8 rw	PD7 rw	PD6 rw	PD5 rw	PD4 rw	PD3 rw	PD2 rw	PD1 rw	PD0 rw

Toggle fields

PD0

Bit 0: Port A pull-down bit y (y=0..15).

PD1

Bit 1: Port A pull-down bit y (y=0..15).

PD2

Bit 2: Port A pull-down bit y (y=0..15).

PD3

Bit 3: Port A pull-down bit y (y=0..15).

PD4

Bit 4: Port A pull-down bit y (y=0..15).

PD5

Bit 5: Port A pull-down bit y (y=0..15).

PD6

Bit 6: Port A pull-down bit y (y=0..15).

PD7

Bit 7: Port A pull-down bit y (y=0..15).

PD8

Bit 8: Port A pull-down bit y (y=0..15).

PD9

Bit 9: Port A pull-down bit y (y=0..15).

PD10

Bit 10: Port A pull-down bit y (y=0..15).

PD11

Bit 11: Port A pull-down bit y (y=0..15).

PD12

Bit 12: Port A pull-down bit y (y=0..15).

PD13

Bit 13: Port A pull-down bit y (y=0..15).

PD14

Bit 14: Port A pull-down bit y (y=0..15).

PD15

Bit 15: Port A pull-down bit y (y=0..15).

PUCRB

Power Port B pull-up control register

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

0/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PU15 rw	PU14 rw	PU13 rw	PU12 rw	PU11 rw	PU10 rw	PU9 rw	PU8 rw	PU7 rw	PU6 rw	PU5 rw	PU4 rw	PU3 rw	PU2 rw	PU1 rw	PU0 rw

Toggle fields

PU0

Bit 0: Port B pull-up bit y (y=0..15).

PU1

Bit 1: Port B pull-up bit y (y=0..15).

PU2

Bit 2: Port B pull-up bit y (y=0..15).

PU3

Bit 3: Port B pull-up bit y (y=0..15).

PU4

Bit 4: Port B pull-up bit y (y=0..15).

PU5

Bit 5: Port B pull-up bit y (y=0..15).

PU6

Bit 6: Port B pull-up bit y (y=0..15).

PU7

Bit 7: Port B pull-up bit y (y=0..15).

PU8

Bit 8: Port B pull-up bit y (y=0..15).

PU9

Bit 9: Port B pull-up bit y (y=0..15).

PU10

Bit 10: Port B pull-up bit y (y=0..15).

PU11

Bit 11: Port B pull-up bit y (y=0..15).

PU12

Bit 12: Port B pull-up bit y (y=0..15).

PU13

Bit 13: Port B pull-up bit y (y=0..15).

PU14

Bit 14: Port B pull-up bit y (y=0..15).

PU15

Bit 15: Port B pull-up bit y (y=0..15).

PDCRB

Power Port B pull-down control register

Offset: 0x2c, size: 32, reset: 0x00000000, access: read-write

0/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PD15 rw	PD14 rw	PD13 rw	PD12 rw	PD11 rw	PD10 rw	PD9 rw	PD8 rw	PD7 rw	PD6 rw	PD5 rw	PD4 rw	PD3 rw	PD2 rw	PD1 rw	PD0 rw

Toggle fields

PD0

Bit 0: Port B pull-down bit y (y=0..15).

PD1

Bit 1: Port B pull-down bit y (y=0..15).

PD2

Bit 2: Port B pull-down bit y (y=0..15).

PD3

Bit 3: Port B pull-down bit y (y=0..15).

PD4

Bit 4: Port B pull-down bit y (y=0..15).

PD5

Bit 5: Port B pull-down bit y (y=0..15).

PD6

Bit 6: Port B pull-down bit y (y=0..15).

PD7

Bit 7: Port B pull-down bit y (y=0..15).

PD8

Bit 8: Port B pull-down bit y (y=0..15).

PD9

Bit 9: Port B pull-down bit y (y=0..15).

PD10

Bit 10: Port B pull-down bit y (y=0..15).

PD11

Bit 11: Port B pull-down bit y (y=0..15).

PD12

Bit 12: Port B pull-down bit y (y=0..15).

PD13

Bit 13: Port B pull-down bit y (y=0..15).

PD14

Bit 14: Port B pull-down bit y (y=0..15).

PD15

Bit 15: Port B pull-down bit y (y=0..15).

PUCRC

Power Port C pull-up control register

Offset: 0x30, size: 32, reset: 0x00000000, access: read-write

0/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PU15 rw	PU14 rw	PU13 rw	PU12 rw	PU11 rw	PU10 rw	PU9 rw	PU8 rw	PU7 rw	PU6 rw	PU5 rw	PU4 rw	PU3 rw	PU2 rw	PU1 rw	PU0 rw

Toggle fields

PU0

Bit 0: Port C pull-up bit y (y=0..15).

PU1

Bit 1: Port C pull-up bit y (y=0..15).

PU2

Bit 2: Port C pull-up bit y (y=0..15).

PU3

Bit 3: Port C pull-up bit y (y=0..15).

PU4

Bit 4: Port C pull-up bit y (y=0..15).

PU5

Bit 5: Port C pull-up bit y (y=0..15).

PU6

Bit 6: Port C pull-up bit y (y=0..15).

PU7

Bit 7: Port C pull-up bit y (y=0..15).

PU8

Bit 8: Port C pull-up bit y (y=0..15).

PU9

Bit 9: Port C pull-up bit y (y=0..15).

PU10

Bit 10: Port C pull-up bit y (y=0..15).

PU11

Bit 11: Port C pull-up bit y (y=0..15).

PU12

Bit 12: Port C pull-up bit y (y=0..15).

PU13

Bit 13: Port C pull-up bit y (y=0..15).

PU14

Bit 14: Port C pull-up bit y (y=0..15).

PU15

Bit 15: Port C pull-up bit y (y=0..15).

PDCRC

Power Port C pull-down control register

Offset: 0x34, size: 32, reset: 0x00000000, access: read-write

0/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PD15 rw	PD14 rw	PD13 rw	PD12 rw	PD11 rw	PD10 rw	PD9 rw	PD8 rw	PD7 rw	PD6 rw	PD5 rw	PD4 rw	PD3 rw	PD2 rw	PD1 rw	PD0 rw

Toggle fields

PD0

Bit 0: Port C pull-down bit y (y=0..15).

PD1

Bit 1: Port C pull-down bit y (y=0..15).

PD2

Bit 2: Port C pull-down bit y (y=0..15).

PD3

Bit 3: Port C pull-down bit y (y=0..15).

PD4

Bit 4: Port C pull-down bit y (y=0..15).

PD5

Bit 5: Port C pull-down bit y (y=0..15).

PD6

Bit 6: Port C pull-down bit y (y=0..15).

PD7

Bit 7: Port C pull-down bit y (y=0..15).

PD8

Bit 8: Port C pull-down bit y (y=0..15).

PD9

Bit 9: Port C pull-down bit y (y=0..15).

PD10

Bit 10: Port C pull-down bit y (y=0..15).

PD11

Bit 11: Port C pull-down bit y (y=0..15).

PD12

Bit 12: Port C pull-down bit y (y=0..15).

PD13

Bit 13: Port C pull-down bit y (y=0..15).

PD14

Bit 14: Port C pull-down bit y (y=0..15).

PD15

Bit 15: Port C pull-down bit y (y=0..15).

PUCRD

Power Port D pull-up control register

Offset: 0x38, size: 32, reset: 0x00000000, access: read-write

0/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PU15 rw	PU14 rw	PU13 rw	PU12 rw	PU11 rw	PU10 rw	PU9 rw	PU8 rw	PU7 rw	PU6 rw	PU5 rw	PU4 rw	PU3 rw	PU2 rw	PU1 rw	PU0 rw

Toggle fields

PU0

Bit 0: Port D pull-up bit y (y=0..15).

PU1

Bit 1: Port D pull-up bit y (y=0..15).

PU2

Bit 2: Port D pull-up bit y (y=0..15).

PU3

Bit 3: Port D pull-up bit y (y=0..15).

PU4

Bit 4: Port D pull-up bit y (y=0..15).

PU5

Bit 5: Port D pull-up bit y (y=0..15).

PU6

Bit 6: Port D pull-up bit y (y=0..15).

PU7

Bit 7: Port D pull-up bit y (y=0..15).

PU8

Bit 8: Port D pull-up bit y (y=0..15).

PU9

Bit 9: Port D pull-up bit y (y=0..15).

PU10

Bit 10: Port D pull-up bit y (y=0..15).

PU11

Bit 11: Port D pull-up bit y (y=0..15).

PU12

Bit 12: Port D pull-up bit y (y=0..15).

PU13

Bit 13: Port D pull-up bit y (y=0..15).

PU14

Bit 14: Port D pull-up bit y (y=0..15).

PU15

Bit 15: Port D pull-up bit y (y=0..15).

PDCRD

Power Port D pull-down control register

Offset: 0x3c, size: 32, reset: 0x00000000, access: read-write

0/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PD15 rw	PD14 rw	PD13 rw	PD12 rw	PD11 rw	PD10 rw	PD9 rw	PD8 rw	PD7 rw	PD6 rw	PD5 rw	PD4 rw	PD3 rw	PD2 rw	PD1 rw	PD0 rw

Toggle fields

PD0

Bit 0: Port D pull-down bit y (y=0..15).

PD1

Bit 1: Port D pull-down bit y (y=0..15).

PD2

Bit 2: Port D pull-down bit y (y=0..15).

PD3

Bit 3: Port D pull-down bit y (y=0..15).

PD4

Bit 4: Port D pull-down bit y (y=0..15).

PD5

Bit 5: Port D pull-down bit y (y=0..15).

PD6

Bit 6: Port D pull-down bit y (y=0..15).

PD7

Bit 7: Port D pull-down bit y (y=0..15).

PD8

Bit 8: Port D pull-down bit y (y=0..15).

PD9

Bit 9: Port D pull-down bit y (y=0..15).

PD10

Bit 10: Port D pull-down bit y (y=0..15).

PD11

Bit 11: Port D pull-down bit y (y=0..15).

PD12

Bit 12: Port D pull-down bit y (y=0..15).

PD13

Bit 13: Port D pull-down bit y (y=0..15).

PD14

Bit 14: Port D pull-down bit y (y=0..15).

PD15

Bit 15: Port D pull-down bit y (y=0..15).

PUCRE

Power Port E pull-UP control register

Offset: 0x40, size: 32, reset: 0x00000000, access: read-write

0/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PU15 rw	PU14 rw	PU13 rw	PU12 rw	PU11 rw	PU10 rw	PU9 rw	PU8 rw	PU7 rw	PU6 rw	PU5 rw	PU4 rw	PU3 rw	PU2 rw	PU1 rw	PU0 rw

Toggle fields

PU0

Bit 0: Port E pull-up bit y (y=0..15).

PU1

Bit 1: Port E pull-up bit y (y=0..15).

PU2

Bit 2: Port E pull-up bit y (y=0..15).

PU3

Bit 3: Port E pull-up bit y (y=0..15).

PU4

Bit 4: Port E pull-up bit y (y=0..15).

PU5

Bit 5: Port E pull-up bit y (y=0..15).

PU6

Bit 6: Port E pull-up bit y (y=0..15).

PU7

Bit 7: Port E pull-up bit y (y=0..15).

PU8

Bit 8: Port E pull-up bit y (y=0..15).

PU9

Bit 9: Port E pull-up bit y (y=0..15).

PU10

Bit 10: Port E pull-up bit y (y=0..15).

PU11

Bit 11: Port E pull-up bit y (y=0..15).

PU12

Bit 12: Port E pull-up bit y (y=0..15).

PU13

Bit 13: Port E pull-up bit y (y=0..15).

PU14

Bit 14: Port E pull-up bit y (y=0..15).

PU15

Bit 15: Port E pull-up bit y (y=0..15).

PDCRE

Power Port E pull-down control register

Offset: 0x44, size: 32, reset: 0x00000000, access: read-write

0/16 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PD15 rw	PD14 rw	PD13 rw	PD12 rw	PD11 rw	PD10 rw	PD9 rw	PD8 rw	PD7 rw	PD6 rw	PD5 rw	PD4 rw	PD3 rw	PD2 rw	PD1 rw	PD0 rw

Toggle fields

PD0

Bit 0: Port E pull-down bit y (y=0..15).

PD1

Bit 1: Port E pull-down bit y (y=0..15).

PD2

Bit 2: Port E pull-down bit y (y=0..15).

PD3

Bit 3: Port E pull-down bit y (y=0..15).

PD4

Bit 4: Port E pull-down bit y (y=0..15).

PD5

Bit 5: Port E pull-down bit y (y=0..15).

PD6

Bit 6: Port E pull-down bit y (y=0..15).

PD7

Bit 7: Port E pull-down bit y (y=0..15).

PD8

Bit 8: Port E pull-down bit y (y=0..15).

PD9

Bit 9: Port E pull-down bit y (y=0..15).

PD10

Bit 10: Port E pull-down bit y (y=0..15).

PD11

Bit 11: Port E pull-down bit y (y=0..15).

PD12

Bit 12: Port E pull-down bit y (y=0..15).

PD13

Bit 13: Port E pull-down bit y (y=0..15).

PD14

Bit 14: Port E pull-down bit y (y=0..15).

PD15

Bit 15: Port E pull-down bit y (y=0..15).

PUCRF

Power Port F pull-up control register

Offset: 0x48, size: 32, reset: 0x00000000, access: read-write

0/14 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		PU13 rw	PU12 rw	PU11 rw	PU10 rw	PU9 rw	PU8 rw	PU7 rw	PU6 rw	PU5 rw	PU4 rw	PU3 rw	PU2 rw	PU1 rw	PU0 rw

Toggle fields

PU0

Bit 0: Port F pull-up bit y (y=0..15).

PU1

Bit 1: Port F pull-up bit y (y=0..15).

PU2

Bit 2: Port F pull-up bit y (y=0..15).

PU3

Bit 3: Port F pull-up bit y (y=0..15).

PU4

Bit 4: Port F pull-up bit y (y=0..15).

PU5

Bit 5: Port F pull-up bit y (y=0..15).

PU6

Bit 6: Port F pull-up bit y (y=0..15).

PU7

Bit 7: Port F pull-up bit y (y=0..15).

PU8

Bit 8: Port F pull-up bit y (y=0..15).

PU9

Bit 9: Port F pull-up bit y (y=0..15).

PU10

Bit 10: Port F pull-up bit y (y=0..15).

PU11

Bit 11: Port F pull-up bit y (y=0..15).

PU12

Bit 12: Port F pull-up bit y (y=0..15).

PU13

Bit 13: Port F pull-up bit y (y=0..15).

PDCRF

Power Port F pull-down control register

Offset: 0x4c, size: 32, reset: 0x00000000, access: read-write

0/14 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		PD13 rw	PD12 rw	PD11 rw	PD10 rw	PD9 rw	PD8 rw	PD7 rw	PD6 rw	PD5 rw	PD4 rw	PD3 rw	PD2 rw	PD1 rw	PD0 rw

Toggle fields

PD0

Bit 0: Port F pull-down bit y (y=0..15).

PD1

Bit 1: Port F pull-down bit y (y=0..15).

PD2

Bit 2: Port F pull-down bit y (y=0..15).

PD3

Bit 3: Port F pull-down bit y (y=0..15).

PD4

Bit 4: Port F pull-down bit y (y=0..15).

PD5

Bit 5: Port F pull-down bit y (y=0..15).

PD6

Bit 6: Port F pull-down bit y (y=0..15).

PD7

Bit 7: Port F pull-down bit y (y=0..15).

PD8

Bit 8: Port F pull-down bit y (y=0..15).

PD9

Bit 9: Port F pull-down bit y (y=0..15).

PD10

Bit 10: Port F pull-down bit y (y=0..15).

PD11

Bit 11: Port F pull-down bit y (y=0..15).

PD12

Bit 12: Port F pull-down bit y (y=0..15).

PD13

Bit 13: Port F pull-down bit y (y=0..15).

RCC

0x40021000: Reset and clock control

169/169 fields covered.

Toggle register map

Offset	Name	31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	CR							PLLRDY	PLLON					CSSON	HSEBYP	HSERDY	HSEON			HSIDIV			HSIRDY	HSIKERON	HSION
0x4	ICSCR																		HSITRIM							HSICAL
0x8	CFGR		MCOPRE				MCOSEL												PPRE			HPRE						SWS			SW
0xc	PLLCFGR	PLLR			PLLREN	PLLQ			PLLQEN			PLLP					PLLPEN		PLLN								PLLM					PLLSRC
0x18	CIER																											PLLSYSRDYIE	HSERDYIE	HSIRDYIE		LSERDYIE	LSIRDYIE
0x1c	CIFR																							LSECSSF	CSSF			PLLSYSRDYF	HSERDYF	HSIRDYF		LSERDYF	LSIRDYF
0x20	CICR																							LSECSSC	CSSC			PLLSYSRDYC	HSERDYC	HSIRDYC		LSERDYC	LSIRDYC
0x24	IOPRSTR																											IOPFRST		IOPDRST	IOPCRST	IOPBRST	IOPARST
0x28	AHBRSTR														RNGRST		AESRST				CRCRST				FLASHRST								DMARST
0x2c	APBRSTR1	LPTIM1RST	LPTIM2RST		PWRRST	DBGRST					I2C2RST	I2C1RST	LPUART1RST			USART2RST			SPI2RST													TIM3RST	TIM2RST
0x30	APBRSTR2												ADCRST		TIM17RST	TIM16RST		TIM14RST	USART1RST		SPI1RST	TIM1RST											SYSCFGRST
0x34	IOPENR																											IOPFEN		IOPDEN	IOPCEN	IOPBEN	IOPAEN
0x38	AHBENR														RNGEN		AESEN				CRCEN				FLASHEN								DMAEN
0x3c	APBENR1	LPTIM1EN	LPTIM2EN		PWREN	DBGEN					I2C2EN	I2C1EN	LPUART1EN			USART2EN			SPI2EN			WWDGEN	RTCAPBEN									TIM3EN	TIM2EN
0x40	APBENR2												ADCEN		TIM17EN	TIM16EN		TIM14EN	USART1EN		SPI1EN	TIM1EN											SYSCFGEN
0x44	IOPSMENR																											IOPFSMEN		IOPDSMEN	IOPCSMEN	IOPBSMEN	IOPASMEN
0x48	AHBSMENR														RNGSMEN		AESSMEN				CRCSMEN			SRAMSMEN	FLASHSMEN								DMASMEN
0x4c	APBSMENR1	LPTIM1SMEN	LPTIM2SMEN		PWRSMEN	DBGSMEN					I2C2SMEN	I2C1SMEN	LPUART1SMEN			USART2SMEN			SPI2SMEN			WWDGSMEN	RTCAPBSMEN									TIM3SMEN	TIM2SMEN
0x50	APBSMENR2												ADCSMEN		TIM17SMEN	TIM16SMEN		TIM14SMEN	USART1SMEN		SPI1SMEN	TIM1SMEN											SYSCFGSMEN
0x54	CCIPR	ADCSEL		RNGDIV		RNGSEL					TIM1SEL	LPTIM2SEL		LPTIM1SEL				I2S1SEL		I2C1SEL		LPUART1SEL										USART1SEL
0x5c	BDCR							LSCOSEL	LSCOEN								BDRST	RTCEN						RTCSEL			LSECSSD	LSECSSON	LSEDRV		LSEBYP	LSERDY	LSEON
0x60	CSR	LPWRRSTF	WWDGRSTF	IWDGRSTF	SFTRSTF	PWRRSTF	PINRSTF	OBLRSTF		RMVF																						LSIRDY	LSION

Toggle registers

CR

Clock control register

Offset: 0x0, size: 32, reset: 0x00000063, access: read-write

10/10 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
						PLLRDY rw	PLLON rw					CSSON rw	HSEBYP rw	HSERDY rw	HSEON rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		HSIDIV rw			HSIRDY rw	HSIKERON rw	HSION rw

Toggle fields

HSION

Bit 8: HSI16 clock enable.

Allowed values:
0: Disabled: HSI oscillator powered off
1: Enabled: HSI oscillator enabled

HSIKERON

Bit 9: HSI16 always enable for peripheral kernels.

Allowed values:
0: NotForce: No effect on HSI16 oscillator
1: Forced: HSI16 oscillator forced on even in Stop modes

HSIRDY

Bit 10: HSI16 clock ready flag.

Allowed values:
0: NotReady: HSI oscillator not ready
1: Ready: HSI oscillator ready

HSIDIV

Bits 11-13: HSI16 clock division factor.

Allowed values:
0: Div1: Divide HSI16 by 1
1: Div2: Divide HSI16 by 2
2: Div4: Divide HSI16 by 4
3: Div8: Divide HSI16 by 8
4: Div16: Divide HSI16 by 16
5: Div32: Divide HSI16 by 32
6: Div64: Divide HSI16 by 64
7: Div128: Divide HSI16 by 128

HSEON

Bit 16: HSE clock enable.

Allowed values:
0: Disabled: HSE oscillator powered off
1: Enabled: HSE oscillator enabled

HSERDY

Bit 17: HSE clock ready flag.

Allowed values:
0: NotReady: HSE oscillator not ready
1: Ready: HSE oscillator ready

HSEBYP

Bit 18: HSE crystal oscillator bypass.

Allowed values:
0: Crystal: HSE is a crystal oscillator or ceramic resonator
1: ExtClock: HSE is driven by an external clock

CSSON

Bit 19: Clock security system enable.

Allowed values:
0: Disabled: HSE clock is not monitored
1: Enabled: HSE clock monitor enabled when HSE is ready, otherwise disabled

PLLON

Bit 24: PLL enable.

Allowed values:
0: Disabled: PLL powered off
1: Enabled: PLL enabled

PLLRDY

Bit 25: PLL clock ready flag.

Allowed values:
0: Unlocked: PLL unlocked
1: Locked: PLL locked

ICSCR

Internal clock sources calibration register

Offset: 0x4, size: 32, reset: 0x10000000, access: Unspecified

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	HSITRIM rw							HSICAL r

Toggle fields

HSICAL

Bits 0-7: HSI16 clock calibration.

Allowed values: 0x0-0xff

HSITRIM

Bits 8-14: HSI16 clock trimming.

Allowed values: 0x0-0x7f

CFGR

Clock configuration register

Offset: 0x8, size: 32, reset: 0x00000000, access: Unspecified

6/6 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
	MCOPRE r				MCOSEL rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	PPRE rw			HPRE rw						SWS r			SW rw

Toggle fields

SW

Bits 0-2: System clock switch.

Allowed values:
0: HSISYS: HSISYS clock selected
1: HSE: HSE clock selected
2: PLLR: PLLRCLK clock selected
3: LSI: LSI clock selected
4: LSE: LSE clock selected

SWS

Bits 3-5: System clock switch status.

Allowed values:
0: HSISYS: HSISYS clock selected
1: HSE: HSE clock selected
2: PLLR: PLLRCLK clock selected
3: LSI: LSI clock selected
4: LSE: LSE clock selected

HPRE

Bits 8-11: AHB prescaler.

Allowed values:
8: Div2: Divide by 2
9: Div4: Divide by 4
10: Div8: Divide by 8
11: Div16: Divide by 16
12: Div64: Divide by 64
13: Div128: Divide by 128
14: Div256: Divide by 256
15: Div512: Divide by 512
0 (+): Div1: Divide by 1

PPRE

Bits 12-14: APB prescaler.

Allowed values:
4: Div2: Divide by 2
5: Div4: Divide by 4
6: Div8: Divide by 8
7: Div16: Divide by 16
0 (+): Div1: Divide by 1

MCOSEL

Bits 24-26: Microcontroller clock output.

Allowed values:
0: NoClock: No clock
1: SYSCLK: SYSCLK clock selected
3: HSI16: HSI16 oscillator clock selected
4: HSE: HSE oscillator clock selected
5: PLLR: PLLRCLK clock selected
6: LSI: LSI oscillator clock selected
7: LSE: LSE oscillator clock selected

MCOPRE

Bits 28-30: Microcontroller clock output prescaler.

Allowed values:
0: Div1: Divide by 1
1: Div2: Divide by 2
2: Div3: Divide by 4
3: Div8: Divide by 8
4: Div16: Divide by 16
5: Div32: Divide by 32
6: Div64: Divide by 64
7: Div128: Divide by 128

PLLCFGR

PLL configuration register

Offset: 0xc, size: 32, reset: 0x00001000, access: read-write

9/9 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PLLR rw			PLLREN rw	PLLQ rw			PLLQEN rw			PLLP rw					PLLPEN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	PLLN rw								PLLM rw					PLLSRC rw

Toggle fields

PLLSRC

Bits 0-1: PLL input clock source.

Allowed values:
0: NoClock: No clock selected (saves power)
2: HSI16: HSI16 clock selected
3: HSE: HSE clock selected

PLLM

Bits 4-6: Division factor M of the PLL input clock divider.

Allowed values: 0x0-0x7

PLLN

Bits 8-14: PLL frequency multiplication factor N.

Allowed values: 0x8-0x56

PLLPEN

Bit 16: PLLPCLK clock output enable.

Allowed values:
0: Disabled: PLL output disabled (saves power)
1: Enabled: PLL output enabled

PLLP

Bits 17-21: PLL VCO division factor P for PLLPCLK clock output.

Allowed values: 0x1-0x1f

PLLQEN

Bit 24: PLLQCLK clock output enable.

Allowed values:
0: Disabled: PLL output disabled (saves power)
1: Enabled: PLL output enabled

PLLQ

Bits 25-27: PLL VCO division factor Q for PLLQCLK clock output.

Allowed values: 0x1-0x7

PLLREN

Bit 28: PLLRCLK clock output enable.

Allowed values:
0: Disabled: PLL output disabled (saves power)
1: Enabled: PLL output enabled

PLLR

Bits 29-31: PLL VCO division factor R for PLLRCLK clock output.

Allowed values: 0x1-0x7

CIER

Clock interrupt enable register

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

5/5 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
										PLLSYSRDYIE rw	HSERDYIE rw	HSIRDYIE rw		LSERDYIE rw	LSIRDYIE rw

Toggle fields

LSIRDYIE

Bit 0: LSI ready interrupt enable.

Allowed values:
0: Disabled: Interrupt disabled
1: Enabled: Interrupt enabled

LSERDYIE

Bit 1: LSE ready interrupt enable.

Allowed values:
0: Disabled: Interrupt disabled
1: Enabled: Interrupt enabled

HSIRDYIE

Bit 3: HSI ready interrupt enable.

Allowed values:
0: Disabled: Interrupt disabled
1: Enabled: Interrupt enabled

HSERDYIE

Bit 4: HSE ready interrupt enable.

Allowed values:
0: Disabled: Interrupt disabled
1: Enabled: Interrupt enabled

PLLSYSRDYIE

Bit 5: PLL ready interrupt enable.

Allowed values:
0: Disabled: Interrupt disabled
1: Enabled: Interrupt enabled

CIFR

Clock interrupt flag register

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-only

7/7 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						LSECSSF r	CSSF r			PLLSYSRDYF r	HSERDYF r	HSIRDYF r		LSERDYF r	LSIRDYF r

Toggle fields

LSIRDYF

Bit 0: LSI ready interrupt flag.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

LSERDYF

Bit 1: LSE ready interrupt flag.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

HSIRDYF

Bit 3: HSI ready interrupt flag.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

HSERDYF

Bit 4: HSE ready interrupt flag.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

PLLSYSRDYF

Bit 5: PLL ready interrupt flag.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

CSSF

Bit 8: Clock security system interrupt flag.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

LSECSSF

Bit 9: LSE Clock security system interrupt flag.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

CICR

Clock interrupt clear register

Offset: 0x20, size: 32, reset: 0x00000000, access: write-only

7/7 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						LSECSSC w	CSSC w			PLLSYSRDYC w	HSERDYC w	HSIRDYC w		LSERDYC w	LSIRDYC w

Toggle fields

LSIRDYC

Bit 0: LSI ready interrupt clear.

Allowed values:
1: Clear: Clear interrupt flag

LSERDYC

Bit 1: LSE ready interrupt clear.

Allowed values:
1: Clear: Clear interrupt flag

HSIRDYC

Bit 3: HSI ready interrupt clear.

Allowed values:
1: Clear: Clear interrupt flag

HSERDYC

Bit 4: HSE ready interrupt clear.

Allowed values:
1: Clear: Clear interrupt flag

PLLSYSRDYC

Bit 5: PLL ready interrupt clear.

Allowed values:
1: Clear: Clear interrupt flag

CSSC

Bit 8: Clock security system interrupt clear.

Allowed values:
1: Clear: Clear interrupt flag

LSECSSC

Bit 9: LSE Clock security system interrupt clear.

Allowed values:
1: Clear: Clear interrupt flag

IOPRSTR

GPIO reset register

Offset: 0x24, size: 32, reset: 0x00000000, access: read-write

5/5 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
										IOPFRST rw		IOPDRST rw	IOPCRST rw	IOPBRST rw	IOPARST rw

Toggle fields

IOPARST

Bit 0: I/O port A reset.

Allowed values:
1: Reset: Reset peripheral

IOPBRST

Bit 1: I/O port B reset.

Allowed values:
1: Reset: Reset peripheral

IOPCRST

Bit 2: I/O port C reset.

Allowed values:
1: Reset: Reset peripheral

IOPDRST

Bit 3: I/O port D reset.

Allowed values:
1: Reset: Reset peripheral

IOPFRST

Bit 5: I/O port F reset.

Allowed values:
1: Reset: Reset peripheral

AHBRSTR

AHB peripheral reset register

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
													RNGRST rw		AESRST rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			CRCRST rw				FLASHRST rw								DMARST rw

Toggle fields

DMARST

Bit 0: DMA1 reset.

Allowed values:
1: Reset: Reset peripheral

FLASHRST

Bit 8: FLITF reset.

Allowed values:
1: Reset: Reset peripheral

CRCRST

Bit 12: CRC reset.

Allowed values:
1: Reset: Reset peripheral

AESRST

Bit 16: AES hardware accelerator reset.

Allowed values:
1: Reset: Reset peripheral

RNGRST

Bit 18: Random number generator reset.

Allowed values:
1: Reset: Reset peripheral

APBRSTR1

APB peripheral reset register 1

Offset: 0x2c, size: 32, reset: 0x00000000, access: read-write

11/11 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
LPTIM1RST rw	LPTIM2RST rw		PWRRST rw	DBGRST rw					I2C2RST rw	I2C1RST rw	LPUART1RST rw			USART2RST rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	SPI2RST rw													TIM3RST rw	TIM2RST rw

Toggle fields

TIM2RST

Bit 0: TIM2 timer reset.

Allowed values:
1: Reset: Reset peripheral

TIM3RST

Bit 1: TIM3 timer reset.

Allowed values:
1: Reset: Reset peripheral

SPI2RST

Bit 14: SPI2 reset.

Allowed values:
1: Reset: Reset peripheral

USART2RST

Bit 17: USART2 reset.

Allowed values:
1: Reset: Reset peripheral

LPUART1RST

Bit 20: LPUART1 reset.

Allowed values:
1: Reset: Reset peripheral

I2C1RST

Bit 21: I2C1 reset.

Allowed values:
1: Reset: Reset peripheral

I2C2RST

Bit 22: I2C2 reset.

Allowed values:
1: Reset: Reset peripheral

DBGRST

Bit 27: Debug support reset.

Allowed values:
1: Reset: Reset peripheral

PWRRST

Bit 28: Power interface reset.

Allowed values:
1: Reset: Reset peripheral

LPTIM2RST

Bit 30: Low Power Timer 2 reset.

Allowed values:
1: Reset: Reset peripheral

LPTIM1RST

Bit 31: Low Power Timer 1 reset.

Allowed values:
1: Reset: Reset peripheral

APBRSTR2

APB peripheral reset register 2

Offset: 0x30, size: 32, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
											ADCRST rw		TIM17RST rw	TIM16RST rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TIM14RST rw	USART1RST rw		SPI1RST rw	TIM1RST rw											SYSCFGRST rw

Toggle fields

SYSCFGRST

Bit 0: SYSCFG, COMP and VREFBUF reset.

Allowed values:
1: Reset: Reset peripheral

TIM1RST

Bit 11: TIM1 timer reset.

Allowed values:
1: Reset: Reset peripheral

SPI1RST

Bit 12: SPI1 reset.

Allowed values:
1: Reset: Reset peripheral

USART1RST

Bit 14: USART1 reset.

Allowed values:
1: Reset: Reset peripheral

TIM14RST

Bit 15: TIM14 timer reset.

Allowed values:
1: Reset: Reset peripheral

TIM16RST

Bit 17: TIM16 timer reset.

Allowed values:
1: Reset: Reset peripheral

TIM17RST

Bit 18: TIM17 timer reset.

Allowed values:
1: Reset: Reset peripheral

ADCRST

Bit 20: ADC reset.

Allowed values:
1: Reset: Reset peripheral

IOPENR

GPIO clock enable register

Offset: 0x34, size: 32, reset: 0x00000000, access: read-write

5/5 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
										IOPFEN rw		IOPDEN rw	IOPCEN rw	IOPBEN rw	IOPAEN rw

Toggle fields

IOPAEN

Bit 0: I/O port A clock enable.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

IOPBEN

Bit 1: I/O port B clock enable.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

IOPCEN

Bit 2: I/O port C clock enable.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

IOPDEN

Bit 3: I/O port D clock enable.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

IOPFEN

Bit 5: I/O port F clock enable.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

AHBENR

AHB peripheral clock enable register

Offset: 0x38, size: 32, reset: 0x00000000, access: read-write

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
													RNGEN rw		AESEN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			CRCEN rw				FLASHEN rw								DMAEN rw

Toggle fields

DMAEN

Bit 0: DMA clock enable.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

FLASHEN

Bit 8: Flash memory interface clock enable.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

CRCEN

Bit 12: CRC clock enable.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

AESEN

Bit 16: AES hardware accelerator.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

RNGEN

Bit 18: Random number generator clock enable.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

APBENR1

APB peripheral clock enable register 1

Offset: 0x3c, size: 32, reset: 0x00000000, access: read-write

13/13 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
LPTIM1EN rw	LPTIM2EN rw		PWREN rw	DBGEN rw					I2C2EN rw	I2C1EN rw	LPUART1EN rw			USART2EN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	SPI2EN rw			WWDGEN rw	RTCAPBEN rw									TIM3EN rw	TIM2EN rw

Toggle fields

TIM2EN

Bit 0: TIM2 timer clock enable.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

TIM3EN

Bit 1: TIM3 timer clock enable.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

RTCAPBEN

Bit 10: RTC APB clock enable.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

WWDGEN

Bit 11: WWDG clock enable.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

SPI2EN

Bit 14: SPI2 clock enable.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

USART2EN

Bit 17: USART2 clock enable.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

LPUART1EN

Bit 20: LPUART1 clock enable.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

I2C1EN

Bit 21: I2C1 clock enable.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

I2C2EN

Bit 22: I2C2 clock enable.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

DBGEN

Bit 27: Debug support clock enable.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

PWREN

Bit 28: Power interface clock enable.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

LPTIM2EN

Bit 30: LPTIM2 clock enable.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

LPTIM1EN

Bit 31: LPTIM1 clock enable.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

APBENR2

APB peripheral clock enable register 2

Offset: 0x40, size: 32, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
											ADCEN rw		TIM17EN rw	TIM16EN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TIM14EN rw	USART1EN rw		SPI1EN rw	TIM1EN rw											SYSCFGEN rw

Toggle fields

SYSCFGEN

Bit 0: SYSCFG, COMP and VREFBUF clock enable.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

TIM1EN

Bit 11: TIM1 timer clock enable.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

SPI1EN

Bit 12: SPI1 clock enable.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

USART1EN

Bit 14: USART1 clock enable.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

TIM14EN

Bit 15: TIM14 timer clock enable.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

TIM16EN

Bit 17: TIM16 timer clock enable.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

TIM17EN

Bit 18: TIM16 timer clock enable.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

ADCEN

Bit 20: ADC clock enable.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

IOPSMENR

GPIO in Sleep mode clock enable register

Offset: 0x44, size: 32, reset: 0x00000000, access: read-write

5/5 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
										IOPFSMEN rw		IOPDSMEN rw	IOPCSMEN rw	IOPBSMEN rw	IOPASMEN rw

Toggle fields

IOPASMEN

Bit 0: I/O port A clock enable during Sleep mode.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

IOPBSMEN

Bit 1: I/O port B clock enable during Sleep mode.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

IOPCSMEN

Bit 2: I/O port C clock enable during Sleep mode.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

IOPDSMEN

Bit 3: I/O port D clock enable during Sleep mode.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

IOPFSMEN

Bit 5: I/O port F clock enable during Sleep mode.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

AHBSMENR

AHB peripheral clock enable in Sleep mode register

Offset: 0x48, size: 32, reset: 0x00000000, access: read-write

6/6 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
													RNGSMEN rw		AESSMEN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			CRCSMEN rw			SRAMSMEN rw	FLASHSMEN rw								DMASMEN rw

Toggle fields

DMASMEN

Bit 0: DMA clock enable during Sleep mode.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

FLASHSMEN

Bit 8: Flash memory interface clock enable during Sleep mode.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

SRAMSMEN

Bit 9: SRAM clock enable during Sleep mode.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

CRCSMEN

Bit 12: CRC clock enable during Sleep mode.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

AESSMEN

Bit 16: AES hardware accelerator clock enable during Sleep mode.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

RNGSMEN

Bit 18: Random number generator clock enable during Sleep mode.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

APBSMENR1

APB peripheral clock enable in Sleep mode register 1

Offset: 0x4c, size: 32, reset: 0x00000000, access: read-write

13/13 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
LPTIM1SMEN rw	LPTIM2SMEN rw		PWRSMEN rw	DBGSMEN rw					I2C2SMEN rw	I2C1SMEN rw	LPUART1SMEN rw			USART2SMEN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	SPI2SMEN rw			WWDGSMEN rw	RTCAPBSMEN rw									TIM3SMEN rw	TIM2SMEN rw

Toggle fields

TIM2SMEN

Bit 0: TIM2 timer clock enable during Sleep mode.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

TIM3SMEN

Bit 1: TIM3 timer clock enable during Sleep mode.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

RTCAPBSMEN

Bit 10: RTC APB clock enable during Sleep mode.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

WWDGSMEN

Bit 11: WWDG clock enable during Sleep mode.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

SPI2SMEN

Bit 14: SPI2 clock enable during Sleep mode.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

USART2SMEN

Bit 17: USART2 clock enable during Sleep mode.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

LPUART1SMEN

Bit 20: LPUART1 clock enable during Sleep mode.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

I2C1SMEN

Bit 21: I2C1 clock enable during Sleep mode.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

I2C2SMEN

Bit 22: I2C2 clock enable during Sleep mode.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

DBGSMEN

Bit 27: Debug support clock enable during Sleep mode.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

PWRSMEN

Bit 28: Power interface clock enable during Sleep mode.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

LPTIM2SMEN

Bit 30: Low Power Timer 2 clock enable during Sleep mode.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

LPTIM1SMEN

Bit 31: Low Power Timer 1 clock enable during Sleep mode.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

APBSMENR2

APB peripheral clock enable in Sleep mode register 2

Offset: 0x50, size: 32, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
											ADCSMEN rw		TIM17SMEN rw	TIM16SMEN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TIM14SMEN rw	USART1SMEN rw		SPI1SMEN rw	TIM1SMEN rw											SYSCFGSMEN rw

Toggle fields

SYSCFGSMEN

Bit 0: SYSCFG, COMP and VREFBUF clock enable during Sleep mode.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

TIM1SMEN

Bit 11: TIM1 timer clock enable during Sleep mode.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

SPI1SMEN

Bit 12: SPI1 clock enable during Sleep mode.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

USART1SMEN

Bit 14: USART1 clock enable during Sleep mode.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

TIM14SMEN

Bit 15: TIM14 timer clock enable during Sleep mode.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

TIM16SMEN

Bit 17: TIM16 timer clock enable during Sleep mode.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

TIM17SMEN

Bit 18: TIM16 timer clock enable during Sleep mode.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

ADCSMEN

Bit 20: ADC clock enable during Sleep mode.

Allowed values:
0: Disabled: Peripheral disabled (typically saves power)
1: Enabled: Peripheral enabled

CCIPR

Peripherals independent clock configuration register

Offset: 0x54, size: 32, reset: 0x00000000, access: read-write

10/10 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ADCSEL rw		RNGDIV rw		RNGSEL rw					TIM1SEL rw	LPTIM2SEL rw		LPTIM1SEL rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
I2S1SEL rw		I2C1SEL rw		LPUART1SEL rw										USART1SEL rw

Toggle fields

USART1SEL

Bits 0-1: USART1 clock source selection.

Allowed values:
0: PCLK: PCLK clock selected
1: SYSCLK: SYSCLK clock selected
2: HSI16: HSI16 clock selected
3: LSE: LSE clock selected

LPUART1SEL

Bits 10-11: LPUART1 clock source selection.

Allowed values:
0: PCLK: PCLK clock selected
1: SYSCLK: SYSCLK clock selected
2: HSI16: HSI16 clock selected
3: LSE: LSE clock selected

I2C1SEL

Bits 12-13: I2C1 clock source selection.

Allowed values:
0: PCLK: PCLK clock selected
1: SYSCLK: SYSCLK clock selected
2: HSI16: HSI16 clock selected

I2S1SEL

Bits 14-15: I2S1 clock source selection.

Allowed values:
0: SYSCLK: SYSCLK clock selected
1: PLLP: PLLPCLK clock selected
2: HSI16: HSI16 clock selected
3: CKIN: I2S_CKIN clock selected

LPTIM1SEL

Bits 18-19: LPTIM1 clock source selection.

Allowed values:
0: PCLK: PCLK clock selected
1: LSI: LSI clock selected
2: HSI16: HSI16 clock selected
3: LSE: LSE clock selected

LPTIM2SEL

Bits 20-21: LPTIM2 clock source selection.

Allowed values:
0: PCLK: PCLK clock selected
1: LSI: LSI clock selected
2: HSI16: HSI16 clock selected
3: LSE: LSE clock selected

TIM1SEL

Bit 22: TIM1 clock source selection.

Allowed values:
0: TIMP: TIMPCLK clock selected
1: PLLQ: PLLQCLK clock selected

RNGSEL

Bits 26-27: RNG clock source selection.

Allowed values:
0: NoClock: No clock selected
1: HSI16: HSI16 clock selected
2: SYSCLK: SYSCLK clock selected
3: PLLQ: PLLQCLK clock selected

RNGDIV

Bits 28-29: Division factor of RNG clock divider.

Allowed values:
0: Div1: Divide by 1
1: Div2: Divide by 2
2: Div4: Divide by 4
3: Div8: Divide by 8

ADCSEL

Bits 30-31: ADCs clock source selection.

Allowed values:
0: SYSCLK: System clock selected
1: PLLP: PLLPCLK clock selected
2: HSI16: HSI16 clock selected

BDCR

RTC domain control register

Offset: 0x5c, size: 32, reset: 0x00000000, access: read-write

11/11 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
						LSCOSEL rw	LSCOEN rw								BDRST rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RTCEN rw						RTCSEL rw			LSECSSD rw	LSECSSON rw	LSEDRV rw		LSEBYP rw	LSERDY rw	LSEON rw

Toggle fields

LSEON

Bit 0: LSE oscillator enable.

Allowed values:
0: Disabled: LSE oscillator powered off
1: Enabled: LSE oscillator enabled

LSERDY

Bit 1: LSE oscillator ready.

Allowed values:
0: NotReady: LSE oscillator not ready
1: Ready: LSE oscillator ready

LSEBYP

Bit 2: LSE oscillator bypass.

Allowed values:
0: Crystal: LSE is a crystal oscillator or ceramic resonator
1: ExtClock: LSE is driven by an external clock

LSEDRV

Bits 3-4: LSE oscillator drive capability.

Allowed values:
0: Low: Xtal mode lower driving capability
1: MedLow: Xtal mode medium-low driving capability
2: MedHigh: Xtal mode medium-high driving capability
3: High: Xtal mode higher driving capability

LSECSSON

Bit 5: CSS on LSE enable.

Allowed values:
0: Disabled: LSE clock is not monitored
1: Enabled: LSE clock monitor enabled

LSECSSD

Bit 6: CSS on LSE failure Detection.

Allowed values:
0: NoFailure: No failure detected
1: Failure: Failure detected

RTCSEL

Bits 8-9: RTC clock source selection.

Allowed values:
0: NoClock: No clock selected
1: LSE: LSE clock selected
2: LSI: LSI clock selected
3: HSE32: HSI clock divided by 32 selected

RTCEN

Bit 15: RTC clock enable.

Allowed values:
0: Disabled: RTC disabled (saves power)
1: Enabled: RTC enabled

BDRST

Bit 16: RTC domain software reset.

Allowed values:
1: Reset: RTC domain software reset

LSCOEN

Bit 24: Low-speed clock output (LSCO) enable.

Allowed values:
0: Disabled: Low-speed clock output disabled
1: Enabled: Low-speed clock output enabled

LSCOSEL

Bit 25: Low-speed clock output selection.

Allowed values:
0: LSI: LSI clock selected
1: LSE: LSE clock selected

CSR

Control/status register

Offset: 0x60, size: 32, reset: 0x00000000, access: read-write

10/10 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
LPWRRSTF rw	WWDGRSTF rw	IWDGRSTF rw	SFTRSTF rw	PWRRSTF rw	PINRSTF rw	OBLRSTF rw		RMVF rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														LSIRDY rw	LSION rw

Toggle fields

LSION

Bit 0: LSI oscillator enable.

Allowed values:
0: Disabled: LSI oscillator powered off
1: Enabled: LSI oscillator enabled

LSIRDY

Bit 1: LSI oscillator ready.

Allowed values:
0: NotReady: LSI oscillator not ready
1: Ready: LSI oscillator ready

RMVF

Bit 23: Remove reset flags.

Allowed values:
1: Clear: Clear reset flags

OBLRSTF

Bit 25: Option byte loader reset flag.

Allowed values:
0: NoReset: This reset type has not occurred
1: Reset: This reset type has occurred

PINRSTF

Bit 26: Pin reset flag.

Allowed values:
0: NoReset: This reset type has not occurred
1: Reset: This reset type has occurred

PWRRSTF

Bit 27: BOR or POR/PDR flag.

Allowed values:
0: NoReset: This reset type has not occurred
1: Reset: This reset type has occurred

SFTRSTF

Bit 28: Software reset flag.

Allowed values:
0: NoReset: This reset type has not occurred
1: Reset: This reset type has occurred

IWDGRSTF

Bit 29: Independent window watchdog reset flag.

Allowed values:
0: NoReset: This reset type has not occurred
1: Reset: This reset type has occurred

WWDGRSTF

Bit 30: Window watchdog reset flag.

Allowed values:
0: NoReset: This reset type has not occurred
1: Reset: This reset type has occurred

LPWRRSTF

Bit 31: Low-power reset flag.

Allowed values:
0: NoReset: This reset type has not occurred
1: Reset: This reset type has occurred

RNG

0x40025000: Random number generator

4/10 fields covered.

Toggle register map

Offset	Name	31	15	6	5	3	2	1	0
0x0	CR			BYP	CED	IE	RNGEN
0x4	SR			SEIS	CEIS		SECS	CECS	DRDY
0x8	DR	RNDATA	RNDATA

Toggle registers

CR

control register

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
									BYP rw	CED rw		IE rw	RNGEN rw

Toggle fields

RNGEN

Bit 2: Random number generator enable.

IE

Bit 3: Interrupt enable.

CED

Bit 5: Clock error detection.

BYP

Bit 6: Bypass mode enable.

SR

status register

Offset: 0x4, size: 32, reset: 0x00000000, access: Unspecified

3/5 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
									SEIS rw	CEIS rw			SECS r	CECS r	DRDY r

Toggle fields

DRDY

Bit 0: Data ready.

CECS

Bit 1: Clock error current status.

SECS

Bit 2: Seed error current status.

CEIS

Bit 5: Clock error interrupt status.

SEIS

Bit 6: Seed error interrupt status.

DR

data register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
RNDATA r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RNDATA r

Toggle fields

RNDATA

Bits 0-31: Random data.

RTC

0x40002800: Real-time clock

20/125 fields covered.

Toggle register map

Offset	Name	31	30	29	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	TR									PM	HT		HU					MNT			MNU					ST			SU
0x4	DR								YT				YU				WDU			MT	MU						DT		DU
0x8	SSR																SS
0xc	ICSR															RECALPF									INIT	INITF	RSF	INITS	SHPF	WUTWF	ALRBWF	ALRAWF
0x10	PRER									PREDIV_A								PREDIV_S
0x14	WUTR																WUT
0x18	CR	OUT2EN	TAMPALRM_TYPE	TAMPALRM_PU		TAMPOE	TAMPTS	ITSE	COE	OSEL		POL	COSEL	BKP	SUB1H	ADD1H	TSIE	WUTIE	ALRBIE	ALRAIE	TSE	WUTE	ALRBE	ALRAE		FMT	BYPSHAD	REFCKON	TSEDGE	WUCKSEL
0x24	WPR																								KEY
0x28	CALR																CALP	CALW8	CALW16					CALM
0x2c	SHIFTR	ADD1S																SUBFS
0x30	TSTR									PM	HT		HU					MNT			MNU					ST			SU
0x34	TSDR								YT				YU				WDU			MT	MU						DT		DU
0x38	TSSSR																SS
0x40	ALRM[A]R	MSK4	WDSEL	DT	DU				MSK3	PM	HT		HU				MSK2	MNT			MNU				MSK1	ST			SU
0x44	ALRM[A]SSR				MASKSS													SS
0x48	ALRM[B]R	MSK4	WDSEL	DT	DU				MSK3	PM	HT		HU				MSK2	MNT			MNU				MSK1	ST			SU
0x4c	ALRM[B]SSR				MASKSS													SS
0x50	SR																										ITSF	TSOVF	TSF	WUTF	ALRBF	ALRAF
0x54	MISR																										ITSMF	TSOVMF	TSMF	WUTMF	ALRBMF	ALRAMF
0x5c	SCR																										CITSF	CTSOVF	CTSF	CWUTF	CALRBF	CALRAF

Toggle registers

TR

time register

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

0/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
									PM rw	HT rw		HU rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	MNT rw			MNU rw					ST rw			SU rw

Toggle fields

SU

Bits 0-3: Second units in BCD format.

ST

Bits 4-6: Second tens in BCD format.

MNU

Bits 8-11: Minute units in BCD format.

MNT

Bits 12-14: Minute tens in BCD format.

HU

Bits 16-19: Hour units in BCD format.

HT

Bits 20-21: Hour tens in BCD format.

PM

Bit 22: AM/PM notation.

DR

date register

Offset: 0x4, size: 32, reset: 0x00002101, access: read-write

0/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								YT rw				YU rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
WDU rw			MT rw	MU rw						DT rw		DU rw

Toggle fields

DU

Bits 0-3: Date units in BCD format.

DT

Bits 4-5: Date tens in BCD format.

MU

Bits 8-11: Month units in BCD format.

MT

Bit 12: Month tens in BCD format.

WDU

Bits 13-15: Week day units.

YU

Bits 16-19: Year units in BCD format.

YT

Bits 20-23: Year tens in BCD format.

SSR

sub second register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SS r

Toggle fields

SS

Bits 0-15: Sub second value.

ICSR

initialization and status register

Offset: 0xc, size: 32, reset: 0x00000007, access: Unspecified

6/9 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															RECALPF r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								INIT rw	INITF r	RSF rw	INITS r	SHPF rw	WUTWF r	ALRBWF r	ALRAWF r

Toggle fields

ALRAWF

Bit 0: Alarm A write flag.

ALRBWF

Bit 1: Alarm B write flag.

WUTWF

Bit 2: Wakeup timer write flag.

SHPF

Bit 3: Shift operation pending.

INITS

Bit 4: Initialization status flag.

RSF

Bit 5: Registers synchronization flag.

INITF

Bit 6: Initialization flag.

INIT

Bit 7: Initialization mode.

RECALPF

Bit 16: Recalibration pending Flag.

PRER

prescaler register

Offset: 0x10, size: 32, reset: 0x007F00FF, access: read-write

0/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
									PREDIV_A rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	PREDIV_S rw

Toggle fields

PREDIV_S

Bits 0-14: Synchronous prescaler factor.

PREDIV_A

Bits 16-22: Asynchronous prescaler factor.

WUTR

wakeup timer register

Offset: 0x14, size: 32, reset: 0x0000FFFF, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
WUT rw

Toggle fields

WUT

Bits 0-15: Wakeup auto-reload value bits.

CR

control register

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

0/26 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OUT2EN rw	TAMPALRM_TYPE rw	TAMPALRM_PU rw			TAMPOE rw	TAMPTS rw	ITSE rw	COE rw	OSEL rw		POL rw	COSEL rw	BKP rw	SUB1H rw	ADD1H rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TSIE rw	WUTIE rw	ALRBIE rw	ALRAIE rw	TSE rw	WUTE rw	ALRBE rw	ALRAE rw		FMT rw	BYPSHAD rw	REFCKON rw	TSEDGE rw	WUCKSEL rw

Toggle fields

WUCKSEL

Bits 0-2: WUCKSEL.

TSEDGE

Bit 3: TSEDGE.

REFCKON

Bit 4: REFCKON.

BYPSHAD

Bit 5: BYPSHAD.

FMT

Bit 6: FMT.

ALRAE

Bit 8: ALRAE.

ALRBE

Bit 9: ALRBE.

WUTE

Bit 10: WUTE.

TSE

Bit 11: TSE.

ALRAIE

Bit 12: ALRAIE.

ALRBIE

Bit 13: ALRBIE.

WUTIE

Bit 14: WUTIE.

TSIE

Bit 15: TSIE.

ADD1H

Bit 16: ADD1H.

SUB1H

Bit 17: SUB1H.

BKP

Bit 18: BKP.

COSEL

Bit 19: COSEL.

POL

Bit 20: POL.

OSEL

Bits 21-22: OSEL.

COE

Bit 23: COE.

ITSE

Bit 24: ITSE.

TAMPTS

Bit 25: TAMPTS.

TAMPOE

Bit 26: TAMPOE.

TAMPALRM_PU

Bit 29: TAMPALRM_PU.

TAMPALRM_TYPE

Bit 30: TAMPALRM_TYPE.

OUT2EN

Bit 31: OUT2EN.

WPR

write protection register

Offset: 0x24, size: 32, reset: 0x00000000, access: write-only

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								KEY w

Toggle fields

KEY

Bits 0-7: Write protection key.

CALR

calibration register

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CALP rw	CALW8 rw	CALW16 rw					CALM rw

Toggle fields

CALM

Bits 0-8: Calibration minus.

CALW16

Bit 13: Use a 16-second calibration cycle period.

CALW8

Bit 14: Use an 8-second calibration cycle period.

CALP

Bit 15: Increase frequency of RTC by 488.5 ppm.

SHIFTR

shift control register

Offset: 0x2c, size: 32, reset: 0x00000000, access: write-only

0/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ADD1S w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	SUBFS w

Toggle fields

SUBFS

Bits 0-14: Subtract a fraction of a second.

ADD1S

Bit 31: Add one second.

TSTR

time stamp time register

Offset: 0x30, size: 32, reset: 0x00000000, access: read-write

0/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
									PM rw	HT rw		HU rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	MNT rw			MNU rw					ST rw			SU rw

Toggle fields

SU

Bits 0-3: Second units in BCD format.

ST

Bits 4-6: Second tens in BCD format.

MNU

Bits 8-11: Minute units in BCD format.

MNT

Bits 12-14: Minute tens in BCD format.

HU

Bits 16-19: Hour units in BCD format.

HT

Bits 20-21: Hour tens in BCD format.

PM

Bit 22: AM/PM notation.

TSDR

time stamp date register

Offset: 0x34, size: 32, reset: 0x00002101, access: read-write

0/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								YT rw				YU rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
WDU rw			MT rw	MU rw						DT rw		DU rw

Toggle fields

DU

Bits 0-3: Date units in BCD format.

DT

Bits 4-5: Date tens in BCD format.

MU

Bits 8-11: Month units in BCD format.

MT

Bit 12: Month tens in BCD format.

WDU

Bits 13-15: Week day units.

YU

Bits 16-19: Year units in BCD format.

YT

Bits 20-23: Year tens in BCD format.

TSSSR

timestamp sub second register

Offset: 0x38, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SS r

Toggle fields

SS

Bits 0-15: Sub second value.

ALRM[A]R

Alarm A register

Offset: 0x40, size: 32, reset: 0x00000000, access: read-write

0/14 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MSK4 rw	WDSEL rw	DT rw		DU rw				MSK3 rw	PM rw	HT rw		HU rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MSK2 rw	MNT rw			MNU rw				MSK1 rw	ST rw			SU rw

Toggle fields

SU

Bits 0-3: Second units in BCD format.

ST

Bits 4-6: Second tens in BCD format.

MSK1

Bit 7: Alarm seconds mask.

MNU

Bits 8-11: Minute units in BCD format.

MNT

Bits 12-14: Minute tens in BCD format.

MSK2

Bit 15: Alarm minutes mask.

HU

Bits 16-19: Hour units in BCD format.

HT

Bits 20-21: Hour tens in BCD format.

PM

Bit 22: AM/PM notation.

MSK3

Bit 23: Alarm hours mask.

DU

Bits 24-27: Date units or day in BCD format.

DT

Bits 28-29: Date tens in BCD format.

WDSEL

Bit 30: Week day selection.

MSK4

Bit 31: Alarm date mask.

ALRM[A]SSR

Alarm A sub-second register

Offset: 0x44, size: 32, reset: 0x00000000, access: read-write

0/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				MASKSS rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	SS rw

Toggle fields

SS

Bits 0-14: Sub seconds value.

MASKSS

Bits 24-27: Mask the most-significant bits starting at this bit.

ALRM[B]R

Alarm B register

Offset: 0x48, size: 32, reset: 0x00000000, access: read-write

0/14 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MSK4 rw	WDSEL rw	DT rw		DU rw				MSK3 rw	PM rw	HT rw		HU rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MSK2 rw	MNT rw			MNU rw				MSK1 rw	ST rw			SU rw

Toggle fields

SU

Bits 0-3: Second units in BCD format.

ST

Bits 4-6: Second tens in BCD format.

MSK1

Bit 7: Alarm seconds mask.

MNU

Bits 8-11: Minute units in BCD format.

MNT

Bits 12-14: Minute tens in BCD format.

MSK2

Bit 15: Alarm minutes mask.

HU

Bits 16-19: Hour units in BCD format.

HT

Bits 20-21: Hour tens in BCD format.

PM

Bit 22: AM/PM notation.

MSK3

Bit 23: Alarm hours mask.

DU

Bits 24-27: Date units or day in BCD format.

DT

Bits 28-29: Date tens in BCD format.

WDSEL

Bit 30: Week day selection.

MSK4

Bit 31: Alarm date mask.

ALRM[B]SSR

Alarm B sub-second register

Offset: 0x4c, size: 32, reset: 0x00000000, access: read-write

0/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				MASKSS rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	SS rw

Toggle fields

SS

Bits 0-14: Sub seconds value.

MASKSS

Bits 24-27: Mask the most-significant bits starting at this bit.

SR

status register

Offset: 0x50, size: 32, reset: 0x00000000, access: read-only

6/6 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
										ITSF r	TSOVF r	TSF r	WUTF r	ALRBF r	ALRAF r

Toggle fields

ALRAF

Bit 0: ALRAF.

ALRBF

Bit 1: ALRBF.

WUTF

Bit 2: WUTF.

TSF

Bit 3: TSF.

TSOVF

Bit 4: TSOVF.

ITSF

Bit 5: ITSF.

MISR

masked interrupt status register

Offset: 0x54, size: 32, reset: 0x00000000, access: read-only

6/6 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
										ITSMF r	TSOVMF r	TSMF r	WUTMF r	ALRBMF r	ALRAMF r

Toggle fields

ALRAMF

Bit 0: ALRAMF.

ALRBMF

Bit 1: ALRBMF.

WUTMF

Bit 2: WUTMF.

TSMF

Bit 3: TSMF.

TSOVMF

Bit 4: TSOVMF.

ITSMF

Bit 5: ITSMF.

SCR

status clear register

Offset: 0x5c, size: 32, reset: 0x00000000, access: read-write

0/6 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
										CITSF rw	CTSOVF rw	CTSF rw	CWUTF rw	CALRBF rw	CALRAF rw

Toggle fields

CALRAF

Bit 0: CALRAF.

CALRBF

Bit 1: CALRBF.

CWUTF

Bit 2: CWUTF.

CTSF

Bit 3: CTSF.

CTSOVF

Bit 4: CTSOVF.

CITSF

Bit 5: CITSF.

SPI1

0x40013000: Serial peripheral interface/Inter-IC sound

53/53 fields covered.

Toggle register map

Offset	Name	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0 (16-bit)	CR1	BIDIMODE	BIDIOE	CRCEN	CRCNEXT	CRCL	RXONLY	SSM	SSI	LSBFIRST	SPE	BR			MSTR	CPOL	CPHA
0x4 (16-bit)	CR2		LDMA_TX	LDMA_RX	FRXTH	DS				TXEIE	RXNEIE	ERRIE	FRF	NSSP	SSOE	TXDMAEN	RXDMAEN
0x8 (16-bit)	SR				FTLVL		FRLVL		FRE	BSY	OVR	MODF	CRCERR	UDR	CHSIDE	TXE	RXNE
0xc (16-bit)	DR	DR
0xc (8-bit)	DR8									DR
0x10 (16-bit)	CRCPR	CRCPOLY
0x14 (16-bit)	RXCRCR	RxCRC
0x18 (16-bit)	TXCRCR	TxCRC
0x1c (16-bit)	I2SCFGR					I2SMOD	I2SE	I2SCFG		PCMSYNC		I2SSTD		CKPOL	DATLEN		CHLEN
0x20 (16-bit)	I2SPR							MCKOE	ODD	I2SDIV

Toggle registers

CR1

control register 1

Offset: 0x0, size: 16, reset: 0x00000000, access: read-write

14/14 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BIDIMODE rw	BIDIOE rw	CRCEN rw	CRCNEXT rw	CRCL rw	RXONLY rw	SSM rw	SSI rw	LSBFIRST rw	SPE rw	BR rw			MSTR rw	CPOL rw	CPHA rw

Toggle fields

CPHA

Bit 0: Clock phase.

Allowed values:
0: FirstEdge: The first clock transition is the first data capture edge
1: SecondEdge: The second clock transition is the first data capture edge

CPOL

Bit 1: Clock polarity.

Allowed values:
0: IdleLow: CK to 0 when idle
1: IdleHigh: CK to 1 when idle

MSTR

Bit 2: Master selection.

Allowed values:
0: Slave: Slave configuration
1: Master: Master configuration

BR

Bits 3-5: Baud rate control.

Allowed values:
0: Div2: f_PCLK / 2
1: Div4: f_PCLK / 4
2: Div8: f_PCLK / 8
3: Div16: f_PCLK / 16
4: Div32: f_PCLK / 32
5: Div64: f_PCLK / 64
6: Div128: f_PCLK / 128
7: Div256: f_PCLK / 256

SPE

Bit 6: SPI enable.

Allowed values:
0: Disabled: Peripheral disabled
1: Enabled: Peripheral enabled

LSBFIRST

Bit 7: Frame format.

Allowed values:
0: MSBFirst: Data is transmitted/received with the MSB first
1: LSBFirst: Data is transmitted/received with the LSB first

SSI

Bit 8: Internal slave select.

Allowed values:
0: SlaveSelected: 0 is forced onto the NSS pin and the I/O value of the NSS pin is ignored
1: SlaveNotSelected: 1 is forced onto the NSS pin and the I/O value of the NSS pin is ignored

SSM

Bit 9: Software slave management.

Allowed values:
0: Disabled: Software slave management disabled
1: Enabled: Software slave management enabled

RXONLY

Bit 10: Receive only.

Allowed values:
0: FullDuplex: Full duplex (Transmit and receive)
1: OutputDisabled: Output disabled (Receive-only mode)

CRCL

Bit 11: CRC length.

Allowed values:
0: EightBit: 8-bit CRC length
1: SixteenBit: 16-bit CRC length

CRCNEXT

Bit 12: CRC transfer next.

Allowed values:
0: TxBuffer: Next transmit value is from Tx buffer
1: CRC: Next transmit value is from Tx CRC register

CRCEN

Bit 13: Hardware CRC calculation enable.

Allowed values:
0: Disabled: CRC calculation disabled
1: Enabled: CRC calculation enabled

BIDIOE

Bit 14: Output enable in bidirectional mode.

Allowed values:
0: OutputDisabled: Output disabled (receive-only mode)
1: OutputEnabled: Output enabled (transmit-only mode)

BIDIMODE

Bit 15: Bidirectional data mode enable.

Allowed values:
0: Unidirectional: 2-line unidirectional data mode selected
1: Bidirectional: 1-line bidirectional data mode selected

CR2

control register 2

Offset: 0x4, size: 16, reset: 0x00000000, access: read-write

12/12 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	LDMA_TX rw	LDMA_RX rw	FRXTH rw	DS rw				TXEIE rw	RXNEIE rw	ERRIE rw	FRF rw	NSSP rw	SSOE rw	TXDMAEN rw	RXDMAEN rw

Toggle fields

RXDMAEN

Bit 0: Rx buffer DMA enable.

Allowed values:
0: Disabled: Rx buffer DMA disabled
1: Enabled: Rx buffer DMA enabled

TXDMAEN

Bit 1: Tx buffer DMA enable.

Allowed values:
0: Disabled: Tx buffer DMA disabled
1: Enabled: Tx buffer DMA enabled

SSOE

Bit 2: SS output enable.

Allowed values:
0: Disabled: SS output is disabled in master mode
1: Enabled: SS output is enabled in master mode

NSSP

Bit 3: NSS pulse management.

Allowed values:
0: NoPulse: No NSS pulse
1: PulseGenerated: NSS pulse generated

FRF

Bit 4: Frame format.

Allowed values:
0: Motorola: SPI Motorola mode
1: TI: SPI TI mode

ERRIE

Bit 5: Error interrupt enable.

Allowed values:
0: Masked: Error interrupt masked
1: NotMasked: Error interrupt not masked

RXNEIE

Bit 6: RX buffer not empty interrupt enable.

Allowed values:
0: Masked: RXE interrupt masked
1: NotMasked: RXE interrupt not masked

TXEIE

Bit 7: Tx buffer empty interrupt enable.

Allowed values:
0: Masked: TXE interrupt masked
1: NotMasked: TXE interrupt not masked

DS

Bits 8-11: Data size.

Allowed values:
3: FourBit: 4-bit
4: FiveBit: 5-bit
5: SixBit: 6-bit
6: SevenBit: 7-bit
7: EightBit: 8-bit
8: NineBit: 9-bit
9: TenBit: 10-bit
10: ElevenBit: 11-bit
11: TwelveBit: 12-bit
12: ThirteenBit: 13-bit
13: FourteenBit: 14-bit
14: FifteenBit: 15-bit
15: SixteenBit: 16-bit

FRXTH

Bit 12: FIFO reception threshold.

Allowed values:
0: Half: RXNE event is generated if the FIFO level is greater than or equal to 1/2 (16-bit)
1: Quarter: RXNE event is generated if the FIFO level is greater than or equal to 1/4 (8-bit)

LDMA_RX

Bit 13: Last DMA transfer for reception.

Allowed values:
0: Even: Number of data to transfer for receive is even
1: Odd: Number of data to transfer for receive is odd

LDMA_TX

Bit 14: Last DMA transfer for transmission.

Allowed values:
0: Even: Number of data to transfer for transmit is even
1: Odd: Number of data to transfer for transmit is odd

SR

status register

Offset: 0x8, size: 16, reset: 0x00000002, access: Unspecified

11/11 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			FTLVL r		FRLVL r		FRE r	BSY r	OVR r	MODF r	CRCERR rw	UDR r	CHSIDE r	TXE r	RXNE r

Toggle fields

RXNE

Bit 0: Receive buffer not empty.

Allowed values:
0: Empty: Rx buffer empty
1: NotEmpty: Rx buffer not empty

TXE

Bit 1: Transmit buffer empty.

Allowed values:
0: NotEmpty: Tx buffer not empty
1: Empty: Tx buffer empty

CHSIDE

Bit 2: Channel side.

UDR

Bit 3: Underrun flag.

CRCERR

Bit 4: CRC error flag.

Allowed values:
0: Match: CRC value received matches the SPIx_RXCRCR value
1: NoMatch: CRC value received does not match the SPIx_RXCRCR value

MODF

Bit 5: Mode fault.

Allowed values:
0: NoFault: No mode fault occurred
1: Fault: Mode fault occurred

OVR

Bit 6: Overrun flag.

Allowed values:
0: NoOverrun: No overrun occurred
1: Overrun: Overrun occurred

BSY

Bit 7: Busy flag.

Allowed values:
0: NotBusy: SPI not busy
1: Busy: SPI busy

FRE

Bit 8: Frame format error.

Allowed values:
0: NoError: No frame format error
1: Error: A frame format error occurred

FRLVL

Bits 9-10: FIFO reception level.

Allowed values:
0: Empty: Rx FIFO Empty
1: Quarter: Rx 1/4 FIFO
2: Half: Rx 1/2 FIFO
3: Full: Rx FIFO full

FTLVL

Bits 11-12: FIFO transmission level.

Allowed values:
0: Empty: Tx FIFO Empty
1: Quarter: Tx 1/4 FIFO
2: Half: Tx 1/2 FIFO
3: Full: Tx FIFO full

DR

data register

Offset: 0xc, size: 16, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DR rw

Toggle fields

DR

Bits 0-15: Data register.

Allowed values: 0x0-0xffff

DR8

Direct 8-bit access to data register

Offset: 0xc, size: 8, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								DR rw

Toggle fields

DR

Bits 0-7: Data register.

Allowed values: 0x0-0xff

CRCPR

CRC polynomial register

Offset: 0x10, size: 16, reset: 0x00000007, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CRCPOLY rw

Toggle fields

CRCPOLY

Bits 0-15: CRC polynomial register.

Allowed values: 0x0-0xffff

RXCRCR

RX CRC register

Offset: 0x14, size: 16, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RxCRC r

Toggle fields

RxCRC

Bits 0-15: Rx CRC register.

Allowed values: 0x0-0xffff

TXCRCR

TX CRC register

Offset: 0x18, size: 16, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TxCRC r

Toggle fields

TxCRC

Bits 0-15: Tx CRC register.

Allowed values: 0x0-0xffff

I2SCFGR

configuration register

Offset: 0x1c, size: 16, reset: 0x00000000, access: read-write

8/8 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				I2SMOD rw	I2SE rw	I2SCFG rw		PCMSYNC rw		I2SSTD rw		CKPOL rw	DATLEN rw		CHLEN rw

Toggle fields

CHLEN

Bit 0: Channel length (number of bits per audio channel).

Allowed values:
0: SixteenBit: 16-bit wide
1: ThirtyTwoBit: 32-bit wide

DATLEN

Bits 1-2: Data length to be transferred.

Allowed values:
0: SixteenBit: 16-bit data length
1: TwentyFourBit: 24-bit data length
2: ThirtyTwoBit: 32-bit data length

CKPOL

Bit 3: Inactive state clock polarity.

Allowed values:
0: IdleLow: I2S clock inactive state is low level
1: IdleHigh: I2S clock inactive state is high level

I2SSTD

Bits 4-5: standard selection.

Allowed values:
0: Philips: I2S Philips standard
1: MSB: MSB justified standard
2: LSB: LSB justified standard
3: PCM: PCM standard

PCMSYNC

Bit 7: PCM frame synchronization.

Allowed values:
0: Short: Short frame synchronisation
1: Long: Long frame synchronisation

I2SCFG

Bits 8-9: I2S configuration mode.

Allowed values:
0: SlaveTx: Slave - transmit
1: SlaveRx: Slave - receive
2: MasterTx: Master - transmit
3: MasterRx: Master - receive

I2SE

Bit 10: I2S enable.

Allowed values:
0: Disabled: I2S peripheral is disabled
1: Enabled: I2S peripheral is enabled

I2SMOD

Bit 11: I2S mode selection.

Allowed values:
0: SPIMode: SPI mode is selected
1: I2SMode: I2S mode is selected

I2SPR

prescaler register

Offset: 0x20, size: 16, reset: 0x00000000, access: read-write

3/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						MCKOE rw	ODD rw	I2SDIV rw

Toggle fields

I2SDIV

Bits 0-7: linear prescaler.

Allowed values: 0x2-0xff

ODD

Bit 8: Odd factor for the prescaler.

Allowed values:
0: Even: Real divider value is I2SDIV * 2
1: Odd: Real divider value is (I2SDIV * 2) + 1

MCKOE

Bit 9: Master clock output enable.

Allowed values:
0: Disabled: Master clock output is disabled
1: Enabled: Master clock output is enabled

SPI2

0x40003800: Serial peripheral interface/Inter-IC sound

53/53 fields covered.

Toggle register map

Offset	Name	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0 (16-bit)	CR1	BIDIMODE	BIDIOE	CRCEN	CRCNEXT	CRCL	RXONLY	SSM	SSI	LSBFIRST	SPE	BR			MSTR	CPOL	CPHA
0x4 (16-bit)	CR2		LDMA_TX	LDMA_RX	FRXTH	DS				TXEIE	RXNEIE	ERRIE	FRF	NSSP	SSOE	TXDMAEN	RXDMAEN
0x8 (16-bit)	SR				FTLVL		FRLVL		FRE	BSY	OVR	MODF	CRCERR	UDR	CHSIDE	TXE	RXNE
0xc (16-bit)	DR	DR
0xc (8-bit)	DR8									DR
0x10 (16-bit)	CRCPR	CRCPOLY
0x14 (16-bit)	RXCRCR	RxCRC
0x18 (16-bit)	TXCRCR	TxCRC
0x1c (16-bit)	I2SCFGR					I2SMOD	I2SE	I2SCFG		PCMSYNC		I2SSTD		CKPOL	DATLEN		CHLEN
0x20 (16-bit)	I2SPR							MCKOE	ODD	I2SDIV

Toggle registers

CR1

control register 1

Offset: 0x0, size: 16, reset: 0x00000000, access: read-write

14/14 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BIDIMODE rw	BIDIOE rw	CRCEN rw	CRCNEXT rw	CRCL rw	RXONLY rw	SSM rw	SSI rw	LSBFIRST rw	SPE rw	BR rw			MSTR rw	CPOL rw	CPHA rw

Toggle fields

CPHA

Bit 0: Clock phase.

Allowed values:
0: FirstEdge: The first clock transition is the first data capture edge
1: SecondEdge: The second clock transition is the first data capture edge

CPOL

Bit 1: Clock polarity.

Allowed values:
0: IdleLow: CK to 0 when idle
1: IdleHigh: CK to 1 when idle

MSTR

Bit 2: Master selection.

Allowed values:
0: Slave: Slave configuration
1: Master: Master configuration

BR

Bits 3-5: Baud rate control.

Allowed values:
0: Div2: f_PCLK / 2
1: Div4: f_PCLK / 4
2: Div8: f_PCLK / 8
3: Div16: f_PCLK / 16
4: Div32: f_PCLK / 32
5: Div64: f_PCLK / 64
6: Div128: f_PCLK / 128
7: Div256: f_PCLK / 256

SPE

Bit 6: SPI enable.

Allowed values:
0: Disabled: Peripheral disabled
1: Enabled: Peripheral enabled

LSBFIRST

Bit 7: Frame format.

Allowed values:
0: MSBFirst: Data is transmitted/received with the MSB first
1: LSBFirst: Data is transmitted/received with the LSB first

SSI

Bit 8: Internal slave select.

Allowed values:
0: SlaveSelected: 0 is forced onto the NSS pin and the I/O value of the NSS pin is ignored
1: SlaveNotSelected: 1 is forced onto the NSS pin and the I/O value of the NSS pin is ignored

SSM

Bit 9: Software slave management.

Allowed values:
0: Disabled: Software slave management disabled
1: Enabled: Software slave management enabled

RXONLY

Bit 10: Receive only.

Allowed values:
0: FullDuplex: Full duplex (Transmit and receive)
1: OutputDisabled: Output disabled (Receive-only mode)

CRCL

Bit 11: CRC length.

Allowed values:
0: EightBit: 8-bit CRC length
1: SixteenBit: 16-bit CRC length

CRCNEXT

Bit 12: CRC transfer next.

Allowed values:
0: TxBuffer: Next transmit value is from Tx buffer
1: CRC: Next transmit value is from Tx CRC register

CRCEN

Bit 13: Hardware CRC calculation enable.

Allowed values:
0: Disabled: CRC calculation disabled
1: Enabled: CRC calculation enabled

BIDIOE

Bit 14: Output enable in bidirectional mode.

Allowed values:
0: OutputDisabled: Output disabled (receive-only mode)
1: OutputEnabled: Output enabled (transmit-only mode)

BIDIMODE

Bit 15: Bidirectional data mode enable.

Allowed values:
0: Unidirectional: 2-line unidirectional data mode selected
1: Bidirectional: 1-line bidirectional data mode selected

CR2

control register 2

Offset: 0x4, size: 16, reset: 0x00000000, access: read-write

12/12 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	LDMA_TX rw	LDMA_RX rw	FRXTH rw	DS rw				TXEIE rw	RXNEIE rw	ERRIE rw	FRF rw	NSSP rw	SSOE rw	TXDMAEN rw	RXDMAEN rw

Toggle fields

RXDMAEN

Bit 0: Rx buffer DMA enable.

Allowed values:
0: Disabled: Rx buffer DMA disabled
1: Enabled: Rx buffer DMA enabled

TXDMAEN

Bit 1: Tx buffer DMA enable.

Allowed values:
0: Disabled: Tx buffer DMA disabled
1: Enabled: Tx buffer DMA enabled

SSOE

Bit 2: SS output enable.

Allowed values:
0: Disabled: SS output is disabled in master mode
1: Enabled: SS output is enabled in master mode

NSSP

Bit 3: NSS pulse management.

Allowed values:
0: NoPulse: No NSS pulse
1: PulseGenerated: NSS pulse generated

FRF

Bit 4: Frame format.

Allowed values:
0: Motorola: SPI Motorola mode
1: TI: SPI TI mode

ERRIE

Bit 5: Error interrupt enable.

Allowed values:
0: Masked: Error interrupt masked
1: NotMasked: Error interrupt not masked

RXNEIE

Bit 6: RX buffer not empty interrupt enable.

Allowed values:
0: Masked: RXE interrupt masked
1: NotMasked: RXE interrupt not masked

TXEIE

Bit 7: Tx buffer empty interrupt enable.

Allowed values:
0: Masked: TXE interrupt masked
1: NotMasked: TXE interrupt not masked

DS

Bits 8-11: Data size.

Allowed values:
3: FourBit: 4-bit
4: FiveBit: 5-bit
5: SixBit: 6-bit
6: SevenBit: 7-bit
7: EightBit: 8-bit
8: NineBit: 9-bit
9: TenBit: 10-bit
10: ElevenBit: 11-bit
11: TwelveBit: 12-bit
12: ThirteenBit: 13-bit
13: FourteenBit: 14-bit
14: FifteenBit: 15-bit
15: SixteenBit: 16-bit

FRXTH

Bit 12: FIFO reception threshold.

Allowed values:
0: Half: RXNE event is generated if the FIFO level is greater than or equal to 1/2 (16-bit)
1: Quarter: RXNE event is generated if the FIFO level is greater than or equal to 1/4 (8-bit)

LDMA_RX

Bit 13: Last DMA transfer for reception.

Allowed values:
0: Even: Number of data to transfer for receive is even
1: Odd: Number of data to transfer for receive is odd

LDMA_TX

Bit 14: Last DMA transfer for transmission.

Allowed values:
0: Even: Number of data to transfer for transmit is even
1: Odd: Number of data to transfer for transmit is odd

SR

status register

Offset: 0x8, size: 16, reset: 0x00000002, access: Unspecified

11/11 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			FTLVL r		FRLVL r		FRE r	BSY r	OVR r	MODF r	CRCERR rw	UDR r	CHSIDE r	TXE r	RXNE r

Toggle fields

RXNE

Bit 0: Receive buffer not empty.

Allowed values:
0: Empty: Rx buffer empty
1: NotEmpty: Rx buffer not empty

TXE

Bit 1: Transmit buffer empty.

Allowed values:
0: NotEmpty: Tx buffer not empty
1: Empty: Tx buffer empty

CHSIDE

Bit 2: Channel side.

UDR

Bit 3: Underrun flag.

CRCERR

Bit 4: CRC error flag.

Allowed values:
0: Match: CRC value received matches the SPIx_RXCRCR value
1: NoMatch: CRC value received does not match the SPIx_RXCRCR value

MODF

Bit 5: Mode fault.

Allowed values:
0: NoFault: No mode fault occurred
1: Fault: Mode fault occurred

OVR

Bit 6: Overrun flag.

Allowed values:
0: NoOverrun: No overrun occurred
1: Overrun: Overrun occurred

BSY

Bit 7: Busy flag.

Allowed values:
0: NotBusy: SPI not busy
1: Busy: SPI busy

FRE

Bit 8: Frame format error.

Allowed values:
0: NoError: No frame format error
1: Error: A frame format error occurred

FRLVL

Bits 9-10: FIFO reception level.

Allowed values:
0: Empty: Rx FIFO Empty
1: Quarter: Rx 1/4 FIFO
2: Half: Rx 1/2 FIFO
3: Full: Rx FIFO full

FTLVL

Bits 11-12: FIFO transmission level.

Allowed values:
0: Empty: Tx FIFO Empty
1: Quarter: Tx 1/4 FIFO
2: Half: Tx 1/2 FIFO
3: Full: Tx FIFO full

DR

data register

Offset: 0xc, size: 16, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DR rw

Toggle fields

DR

Bits 0-15: Data register.

Allowed values: 0x0-0xffff

DR8

Direct 8-bit access to data register

Offset: 0xc, size: 8, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								DR rw

Toggle fields

DR

Bits 0-7: Data register.

Allowed values: 0x0-0xff

CRCPR

CRC polynomial register

Offset: 0x10, size: 16, reset: 0x00000007, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CRCPOLY rw

Toggle fields

CRCPOLY

Bits 0-15: CRC polynomial register.

Allowed values: 0x0-0xffff

RXCRCR

RX CRC register

Offset: 0x14, size: 16, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RxCRC r

Toggle fields

RxCRC

Bits 0-15: Rx CRC register.

Allowed values: 0x0-0xffff

TXCRCR

TX CRC register

Offset: 0x18, size: 16, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TxCRC r

Toggle fields

TxCRC

Bits 0-15: Tx CRC register.

Allowed values: 0x0-0xffff

I2SCFGR

configuration register

Offset: 0x1c, size: 16, reset: 0x00000000, access: read-write

8/8 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				I2SMOD rw	I2SE rw	I2SCFG rw		PCMSYNC rw		I2SSTD rw		CKPOL rw	DATLEN rw		CHLEN rw

Toggle fields

CHLEN

Bit 0: Channel length (number of bits per audio channel).

Allowed values:
0: SixteenBit: 16-bit wide
1: ThirtyTwoBit: 32-bit wide

DATLEN

Bits 1-2: Data length to be transferred.

Allowed values:
0: SixteenBit: 16-bit data length
1: TwentyFourBit: 24-bit data length
2: ThirtyTwoBit: 32-bit data length

CKPOL

Bit 3: Inactive state clock polarity.

Allowed values:
0: IdleLow: I2S clock inactive state is low level
1: IdleHigh: I2S clock inactive state is high level

I2SSTD

Bits 4-5: standard selection.

Allowed values:
0: Philips: I2S Philips standard
1: MSB: MSB justified standard
2: LSB: LSB justified standard
3: PCM: PCM standard

PCMSYNC

Bit 7: PCM frame synchronization.

Allowed values:
0: Short: Short frame synchronisation
1: Long: Long frame synchronisation

I2SCFG

Bits 8-9: I2S configuration mode.

Allowed values:
0: SlaveTx: Slave - transmit
1: SlaveRx: Slave - receive
2: MasterTx: Master - transmit
3: MasterRx: Master - receive

I2SE

Bit 10: I2S enable.

Allowed values:
0: Disabled: I2S peripheral is disabled
1: Enabled: I2S peripheral is enabled

I2SMOD

Bit 11: I2S mode selection.

Allowed values:
0: SPIMode: SPI mode is selected
1: I2SMode: I2S mode is selected

I2SPR

prescaler register

Offset: 0x20, size: 16, reset: 0x00000000, access: read-write

3/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						MCKOE rw	ODD rw	I2SDIV rw

Toggle fields

I2SDIV

Bits 0-7: linear prescaler.

Allowed values: 0x2-0xff

ODD

Bit 8: Odd factor for the prescaler.

Allowed values:
0: Even: Real divider value is I2SDIV * 2
1: Odd: Real divider value is (I2SDIV * 2) + 1

MCKOE

Bit 9: Master clock output enable.

Allowed values:
0: Disabled: Master clock output is disabled
1: Enabled: Master clock output is enabled

SYSCFG

0x40010000: System configuration controller

95/95 fields covered.

Toggle register map

Offset	Name	24	23	22	21	20	19	18	17	16	14	11	10	9	8	7	6	5	4	3	2	1	0
0x0	CFGR1	I2C3_FMP	I2C_PA10_FMP	I2C_PA9_FMP	I2C2_FMP	I2C1_FMP	I2C_PB9_FMP	I2C_PB8_FMP	I2C_PB7_FMP	I2C_PBx_FMP			UCPD2_STROBE	UCPD1_STROBE	BOOSTEN	IR_MOD		IR_POL	PA12_RMP	PA11_RMP		MEM_MODE
0x18	CFGR2														SRAM_PEF					ECC_LOCK		SRAM_PARITY_LOCK	LOCKUP_LOCK
0x80	ITLINE0																						WWDG
0x88	ITLINE2																					RTC	TAMP
0x8c	ITLINE3																					FLASH_ECC	FLASH_ITF
0x90	ITLINE4																					CRS	RCC
0x94	ITLINE5																					EXTI1	EXTI0
0x98	ITLINE6																					EXTI3	EXTI2
0x9c	ITLINE7											EXTI15	EXTI14	EXTI13	EXTI12	EXTI11	EXTI10	EXTI9	EXTI8	EXTI7	EXTI6	EXTI5	EXTI4
0xa0	ITLINE8																				USB	UCPD2	UCPD1
0xa4	ITLINE9																						DMA1_CH1
0xa8	ITLINE10																					DMA1_CH3	DMA1_CH2
0xac	ITLINE11																				DMA1_CH5	DMA1_CH4	DMAMUX
0xb0	ITLINE12																			COMP3	COMP2	COMP1	ADC
0xb4	ITLINE13																			TIM1_BRK	TIM1_UPD	TIM1_TRG	TIM1_CCU
0xb8	ITLINE14																						TIM1_CC
0xbc	ITLINE15																						TIM2
0xc0	ITLINE16																					TIM4	TIM3
0xc4	ITLINE17																				LPTIM1	DAC	TIM6
0xc8	ITLINE18																					LPTIM2	TIM7
0xcc	ITLINE19																						TIM14
0xd0	ITLINE20																						TIM15
0xd4	ITLINE21																				FDCAN2_IT0	FDCAN1_IT0	TIM16
0xd8	ITLINE22																				FDCAN2_IT1	FDCAN1_IT1	TIM17
0xdc	ITLINE23																						I2C1
0xe0	ITLINE24																					I2C3	I2C2
0xe4	ITLINE25																						SPI1
0xe8	ITLINE26										SPI3												SPI2
0xec	ITLINE27																						USART1
0xf0	ITLINE28																					LPUART2	USART2
0xf4	ITLINE29																		USART6	USART5	LPUART1	USART4	USART3
0xf8	ITLINE30																						CEC
0xfc	ITLINE31																					AES	RNG

Toggle registers

CFGR1

SYSCFG configuration register 1

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

17/17 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
							I2C3_FMP rw	I2C_PA10_FMP rw	I2C_PA9_FMP rw	I2C2_FMP rw	I2C1_FMP rw	I2C_PB9_FMP rw	I2C_PB8_FMP rw	I2C_PB7_FMP rw	I2C_PBx_FMP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
					UCPD2_STROBE rw	UCPD1_STROBE rw	BOOSTEN rw	IR_MOD rw		IR_POL rw	PA12_RMP rw	PA11_RMP rw		MEM_MODE rw

Toggle fields

MEM_MODE

Bits 0-1: Memory mapping selection bits.

Allowed values:
0: MainFlash: Main flash memory mapped at zero address
2: SystemFlash: System flash memory mapped at zero address
3: SRAM: Embedded SRAM mapped at zero address

PA11_RMP

Bit 3: PA11_RMP.

Allowed values:
0: Normal: PA11 pin connected to PA11 GPIO
1: Remap: PA11 pin connected to PA9 GPIO

PA12_RMP

Bit 4: PA11 and PA12 remapping bit..

Allowed values:
0: Normal: PA12 pin connected to PA12 GPIO
1: Remap: PA12 pin connected to PA10 GPIO

IR_POL

Bit 5: IR output polarity selection.

Allowed values:
0: Normal: Output of IRTIM is not inverted
1: Inverted: Output of IRTIM is inverted

IR_MOD

Bits 6-7: IR Modulation Envelope signal selection..

Allowed values:
0: TIM16: IR modulation envelope from TIM16
1: USART1: IR modulation envelope from USART1
2: USART2: IR modulation envelope from USART2

BOOSTEN

Bit 8: I/O analog switch voltage booster enable.

Allowed values:
0: VDD: supply analog switches from VDD
1: BOOST: supply analog switches from dedicated voltage booster

UCPD1_STROBE

Bit 9: Strobe signal bit for UCPD1.

Allowed values:
1: Disconnect: Disconnect the UCPD pull-down resistors

UCPD2_STROBE

Bit 10: Strobe signal bit for UCPD2.

Allowed values:
1: Disconnect: Disconnect the UCPD pull-down resistors

I2C_PBx_FMP

Bit 16: Fast Mode Plus (FM+) driving capability activation bits.

Allowed values:
0: Disabled: Uses normal GPIO drive
1: Enabled: Uses I2C FastMode+ drive

I2C_PB7_FMP

Bit 17: I2C_PB7_FMP.

Allowed values:
0: Disabled: Uses normal GPIO drive
1: Enabled: Uses I2C FastMode+ drive

I2C_PB8_FMP

Bit 18: I2C_PB8_FMP.

Allowed values:
0: Disabled: Uses normal GPIO drive
1: Enabled: Uses I2C FastMode+ drive

I2C_PB9_FMP

Bit 19: I2C_PB9_FMP.

Allowed values:
0: Disabled: Uses normal GPIO drive
1: Enabled: Uses I2C FastMode+ drive

I2C1_FMP

Bit 20: FM+ driving capability activation for I2C1.

Allowed values:
0: Disabled: Uses normal GPIO drive
1: Enabled: Uses I2C FastMode+ drive

I2C2_FMP

Bit 21: FM+ driving capability activation for I2C2.

Allowed values:
0: Disabled: Uses normal GPIO drive
1: Enabled: Uses I2C FastMode+ drive

I2C_PA9_FMP

Bit 22: Fast Mode Plus (FM+) driving capability activation bits.

Allowed values:
0: Disabled: Uses normal GPIO drive
1: Enabled: Uses I2C FastMode+ drive

I2C_PA10_FMP

Bit 23: Fast Mode Plus (FM+) driving capability activation bits.

Allowed values:
0: Disabled: Uses normal GPIO drive
1: Enabled: Uses I2C FastMode+ drive

I2C3_FMP

Bit 24: I2C3_FMP.

Allowed values:
0: Disabled: Uses normal GPIO drive
1: Enabled: Uses I2C FastMode+ drive

CFGR2

SYSCFG configuration register 1

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

4/4 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							SRAM_PEF rw					ECC_LOCK rw		SRAM_PARITY_LOCK rw	LOCKUP_LOCK rw

Toggle fields

LOCKUP_LOCK

Bit 0: Cortex-M0+ LOCKUP bit enable bit.

Allowed values:
0: Disabled: error not connected to timers
1: Enabled: error triggers TIM1/15/16/17 break input

SRAM_PARITY_LOCK

Bit 1: SRAM parity lock bit.

Allowed values:
0: Disabled: error not connected to timers
1: Enabled: error triggers TIM1/15/16/17 break input

ECC_LOCK

Bit 3: ECC error lock bit.

Allowed values:
0: Disabled: error not connected to timers
1: Enabled: error triggers TIM1/15/16/17 break input

SRAM_PEF

Bit 8: SRAM parity error flag.

Allowed values:
0: Normal: No SRAM parity error detected
1: Error: SRAM parity error detected

ITLINE0

interrupt line 0 status register

Offset: 0x80, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
															WWDG r

Toggle fields

WWDG

Bit 0: Window watchdog interrupt pending flag.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

ITLINE2

interrupt line 2 status register

Offset: 0x88, size: 32, reset: 0x00000000, access: read-only

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														RTC r	TAMP r

Toggle fields

TAMP

Bit 0: TAMP.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

RTC

Bit 1: RTC.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

ITLINE3

interrupt line 3 status register

Offset: 0x8c, size: 32, reset: 0x00000000, access: read-only

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														FLASH_ECC r	FLASH_ITF r

Toggle fields

FLASH_ITF

Bit 0: FLASH_ITF.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

FLASH_ECC

Bit 1: FLASH_ECC.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

ITLINE4

interrupt line 4 status register

Offset: 0x90, size: 32, reset: 0x00000000, access: read-only

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														CRS r	RCC r

Toggle fields

RCC

Bit 0: RCC.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

CRS

Bit 1: CRS.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

ITLINE5

interrupt line 5 status register

Offset: 0x94, size: 32, reset: 0x00000000, access: read-only

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														EXTI1 r	EXTI0 r

Toggle fields

EXTI0

Bit 0: EXTI0.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

EXTI1

Bit 1: EXTI1.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

ITLINE6

interrupt line 6 status register

Offset: 0x98, size: 32, reset: 0x00000000, access: read-only

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														EXTI3 r	EXTI2 r

Toggle fields

EXTI2

Bit 0: EXTI2.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

EXTI3

Bit 1: EXTI3.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

ITLINE7

interrupt line 7 status register

Offset: 0x9c, size: 32, reset: 0x00000000, access: read-only

12/12 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				EXTI15 r	EXTI14 r	EXTI13 r	EXTI12 r	EXTI11 r	EXTI10 r	EXTI9 r	EXTI8 r	EXTI7 r	EXTI6 r	EXTI5 r	EXTI4 r

Toggle fields

EXTI4

Bit 0: EXTI4.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

EXTI5

Bit 1: EXTI5.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

EXTI6

Bit 2: EXTI6.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

EXTI7

Bit 3: EXTI7.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

EXTI8

Bit 4: EXTI8.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

EXTI9

Bit 5: EXTI9.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

EXTI10

Bit 6: EXTI10.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

EXTI11

Bit 7: EXTI11.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

EXTI12

Bit 8: EXTI12.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

EXTI13

Bit 9: EXTI13.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

EXTI14

Bit 10: EXTI14.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

EXTI15

Bit 11: EXTI15.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

ITLINE8

interrupt line 8 status register

Offset: 0xa0, size: 32, reset: 0x00000000, access: read-only

3/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
													USB r	UCPD2 r	UCPD1 r

Toggle fields

UCPD1

Bit 0: UCPD1.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

UCPD2

Bit 1: UCPD2.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

USB

Bit 2: USB.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

ITLINE9

interrupt line 9 status register

Offset: 0xa4, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
															DMA1_CH1 r

Toggle fields

DMA1_CH1

Bit 0: DMA1_CH1.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

ITLINE10

interrupt line 10 status register

Offset: 0xa8, size: 32, reset: 0x00000000, access: read-only

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														DMA1_CH3 r	DMA1_CH2 r

Toggle fields

DMA1_CH2

Bit 0: DMA1_CH1.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

DMA1_CH3

Bit 1: DMA1_CH3.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

ITLINE11

interrupt line 11 status register

Offset: 0xac, size: 32, reset: 0x00000000, access: read-only

3/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
													DMA1_CH5 r	DMA1_CH4 r	DMAMUX r

Toggle fields

DMAMUX

Bit 0: DMAMUX.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

DMA1_CH4

Bit 1: DMA1_CH4.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

DMA1_CH5

Bit 2: DMA1_CH5.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

ITLINE12

interrupt line 12 status register

Offset: 0xb0, size: 32, reset: 0x00000000, access: read-only

4/4 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
												COMP3 r	COMP2 r	COMP1 r	ADC r

Toggle fields

ADC

Bit 0: ADC.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

COMP1

Bit 1: COMP1.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

COMP2

Bit 2: COMP2.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

COMP3

Bit 3: COMP3.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

ITLINE13

interrupt line 13 status register

Offset: 0xb4, size: 32, reset: 0x00000000, access: read-only

4/4 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
												TIM1_BRK r	TIM1_UPD r	TIM1_TRG r	TIM1_CCU r

Toggle fields

TIM1_CCU

Bit 0: TIM1_CCU.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

TIM1_TRG

Bit 1: TIM1_TRG.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

TIM1_UPD

Bit 2: TIM1_UPD.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

TIM1_BRK

Bit 3: TIM1_BRK.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

ITLINE14

interrupt line 14 status register

Offset: 0xb8, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
															TIM1_CC r

Toggle fields

TIM1_CC

Bit 0: TIM1_CC.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

ITLINE15

interrupt line 15 status register

Offset: 0xbc, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
															TIM2 r

Toggle fields

TIM2

Bit 0: TIM2.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

ITLINE16

interrupt line 16 status register

Offset: 0xc0, size: 32, reset: 0x00000000, access: read-only

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														TIM4 r	TIM3 r

Toggle fields

TIM3

Bit 0: TIM3.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

TIM4

Bit 1: TIM4.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

ITLINE17

interrupt line 17 status register

Offset: 0xc4, size: 32, reset: 0x00000000, access: read-only

3/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
													LPTIM1 r	DAC r	TIM6 r

Toggle fields

TIM6

Bit 0: TIM6.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

DAC

Bit 1: DAC.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

LPTIM1

Bit 2: LPTIM1.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

ITLINE18

interrupt line 18 status register

Offset: 0xc8, size: 32, reset: 0x00000000, access: read-only

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														LPTIM2 r	TIM7 r

Toggle fields

TIM7

Bit 0: TIM7.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

LPTIM2

Bit 1: LPTIM2.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

ITLINE19

interrupt line 19 status register

Offset: 0xcc, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
															TIM14 r

Toggle fields

TIM14

Bit 0: TIM14.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

ITLINE20

interrupt line 20 status register

Offset: 0xd0, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
															TIM15 r

Toggle fields

TIM15

Bit 0: TIM15.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

ITLINE21

interrupt line 21 status register

Offset: 0xd4, size: 32, reset: 0x00000000, access: read-only

3/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
													FDCAN2_IT0 r	FDCAN1_IT0 r	TIM16 r

Toggle fields

TIM16

Bit 0: TIM16.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

FDCAN1_IT0

Bit 1: FDCAN1_IT0.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

FDCAN2_IT0

Bit 2: FDCAN2_IT0.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

ITLINE22

interrupt line 22 status register

Offset: 0xd8, size: 32, reset: 0x00000000, access: read-only

3/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
													FDCAN2_IT1 r	FDCAN1_IT1 r	TIM17 r

Toggle fields

TIM17

Bit 0: TIM17.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

FDCAN1_IT1

Bit 1: FDCAN1_IT1.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

FDCAN2_IT1

Bit 2: FDCAN2_IT1.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

ITLINE23

interrupt line 23 status register

Offset: 0xdc, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
															I2C1 r

Toggle fields

I2C1

Bit 0: I2C1.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

ITLINE24

interrupt line 24 status register

Offset: 0xe0, size: 32, reset: 0x00000000, access: read-only

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														I2C3 r	I2C2 r

Toggle fields

I2C2

Bit 0: I2C2.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

I2C3

Bit 1: I2C3.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

ITLINE25

interrupt line 25 status register

Offset: 0xe4, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
															SPI1 r

Toggle fields

SPI1

Bit 0: SPI1.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

ITLINE26

interrupt line 26 status register

Offset: 0xe8, size: 32, reset: 0x00000000, access: read-only

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	SPI3 r														SPI2 r

Toggle fields

SPI2

Bit 0: SPI2.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

SPI3

Bit 14: SPI3.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

ITLINE27

interrupt line 27 status register

Offset: 0xec, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
															USART1 r

Toggle fields

USART1

Bit 0: USART1.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

ITLINE28

interrupt line 28 status register

Offset: 0xf0, size: 32, reset: 0x00000000, access: read-only

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														LPUART2 r	USART2 r

Toggle fields

USART2

Bit 0: USART2.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

LPUART2

Bit 1: LPUART2.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

ITLINE29

interrupt line 29 status register

Offset: 0xf4, size: 32, reset: 0x00000000, access: read-only

5/5 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
											USART6 r	USART5 r	LPUART1 r	USART4 r	USART3 r

Toggle fields

USART3

Bit 0: USART3.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

USART4

Bit 1: USART4.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

LPUART1

Bit 2: LPUART1.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

USART5

Bit 3: USART5.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

USART6

Bit 4: USART6.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

ITLINE30

interrupt line 25 status register

Offset: 0xf8, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
															CEC r

Toggle fields

CEC

Bit 0: CEC.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

ITLINE31

interrupt line 25 status register

Offset: 0xfc, size: 32, reset: 0x00000000, access: read-only

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														AES r	RNG r

Toggle fields

RNG

Bit 0: RNG.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

AES

Bit 1: AES.

Allowed values:
0: NotInterrupted: Interrupt not triggered
1: Interrupted: Interrup triggered

TAMP

0x4000b000: Tamper and backup registers

15/52 fields covered.

Toggle register map

Offset	Name	31	25	24	22	21	20	19	18	17	16	15	7	6	4	2	1	0
0x0	CR1					ITAMP6E	ITAMP5E	ITAMP4E	ITAMP3E		ITAMP1E						TAMP2E	TAMP1E
0x4	CR2		TAMP2TRG	TAMP1TRG						TAMP2MSK	TAMP1MSK						TAMP2NOER	TAMP1NOER
0xc	FLTCR												TAMPPUDIS	TAMPPRCH	TAMPFLT	TAMPFREQ
0x2c	IER					ITAMP6IE	ITAMP5IE	ITAMP4IE	ITAMP3IE		ITAMP1IE						TAMP2IE	TAMP1IE
0x30	SR				ITAMP7F	ITAMP6F	ITAMP5F	ITAMP4F	ITAMP3F		ITAMP1F						TAMP2F	TAMP1F
0x34	MISR					ITAMP6MF	ITAMP5MF	ITAMP4MF	ITAMP3MF		ITAMP1MF						TAMP2MF	TAMP1MF
0x3c	SCR				CITAMP7F	CITAMP6F	CITAMP5F	CITAMP4F	CITAMP3F		CITAMP1F						CTAMP2F	CTAMP1F
0x100	BKP[0]R	BKP										BKP
0x104	BKP[1]R	BKP										BKP
0x108	BKP[2]R	BKP										BKP
0x10c	BKP[3]R	BKP										BKP
0x110	BKP[4]R	BKP										BKP

Toggle registers

CR1

control register 1

Offset: 0x0, size: 32, reset: 0xFFFF0000, access: read-write

0/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
										ITAMP6E rw	ITAMP5E rw	ITAMP4E rw	ITAMP3E rw		ITAMP1E rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														TAMP2E rw	TAMP1E rw

Toggle fields

TAMP1E

Bit 0: TAMP1E.

TAMP2E

Bit 1: TAMP2E.

ITAMP1E

Bit 16: ITAMP1E.

ITAMP3E

Bit 18: ITAMP3E.

ITAMP4E

Bit 19: ITAMP4E.

ITAMP5E

Bit 20: ITAMP5E.

ITAMP6E

Bit 21: ITAMP6E.

CR2

control register 2

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

0/6 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
						TAMP2TRG rw	TAMP1TRG rw							TAMP2MSK rw	TAMP1MSK rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														TAMP2NOER rw	TAMP1NOER rw

Toggle fields

TAMP1NOER

Bit 0: TAMP1NOER.

TAMP2NOER

Bit 1: TAMP2NOER.

TAMP1MSK

Bit 16: TAMP1MSK.

TAMP2MSK

Bit 17: TAMP2MSK.

TAMP1TRG

Bit 24: TAMP1TRG.

TAMP2TRG

Bit 25: TAMP2TRG.

FLTCR

TAMP filter control register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								TAMPPUDIS rw	TAMPPRCH rw		TAMPFLT rw		TAMPFREQ rw

Toggle fields

TAMPFREQ

Bits 0-2: TAMPFREQ.

TAMPFLT

Bits 3-4: TAMPFLT.

TAMPPRCH

Bits 5-6: TAMPPRCH.

TAMPPUDIS

Bit 7: TAMPPUDIS.

IER

TAMP interrupt enable register

Offset: 0x2c, size: 32, reset: 0x00000000, access: read-write

0/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
										ITAMP6IE rw	ITAMP5IE rw	ITAMP4IE rw	ITAMP3IE rw		ITAMP1IE rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														TAMP2IE rw	TAMP1IE rw

Toggle fields

TAMP1IE

Bit 0: TAMP1IE.

TAMP2IE

Bit 1: TAMP2IE.

ITAMP1IE

Bit 16: ITAMP1IE.

ITAMP3IE

Bit 18: ITAMP3IE.

ITAMP4IE

Bit 19: ITAMP4IE.

ITAMP5IE

Bit 20: ITAMP5IE.

ITAMP6IE

Bit 21: ITAMP6IE.

SR

TAMP status register

Offset: 0x30, size: 32, reset: 0x00000000, access: read-only

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
									ITAMP7F r	ITAMP6F r	ITAMP5F r	ITAMP4F r	ITAMP3F r		ITAMP1F r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														TAMP2F r	TAMP1F r

Toggle fields

TAMP1F

Bit 0: TAMP1F.

TAMP2F

Bit 1: TAMP2F.

ITAMP1F

Bit 16: ITAMP1F.

ITAMP3F

Bit 18: ITAMP3F.

ITAMP4F

Bit 19: ITAMP4F.

ITAMP5F

Bit 20: ITAMP5F.

ITAMP6F

Bit 21: ITAMP6F.

ITAMP7F

Bit 22: ITAMP7F.

MISR

TAMP masked interrupt status register

Offset: 0x34, size: 32, reset: 0x00000000, access: read-only

7/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
										ITAMP6MF r	ITAMP5MF r	ITAMP4MF r	ITAMP3MF r		ITAMP1MF r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														TAMP2MF r	TAMP1MF r

Toggle fields

TAMP1MF

Bit 0: TAMP1MF:.

TAMP2MF

Bit 1: TAMP2MF.

ITAMP1MF

Bit 16: ITAMP1MF.

ITAMP3MF

Bit 18: ITAMP3MF.

ITAMP4MF

Bit 19: ITAMP4MF.

ITAMP5MF

Bit 20: ITAMP5MF.

ITAMP6MF

Bit 21: ITAMP6MF.

SCR

TAMP status clear register

Offset: 0x3c, size: 32, reset: 0x00000000, access: write-only

0/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
									CITAMP7F w	CITAMP6F w	CITAMP5F w	CITAMP4F w	CITAMP3F w		CITAMP1F w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														CTAMP2F w	CTAMP1F w

Toggle fields

CTAMP1F

Bit 0: CTAMP1F.

CTAMP2F

Bit 1: CTAMP2F.

CITAMP1F

Bit 16: CITAMP1F.

CITAMP3F

Bit 18: CITAMP3F.

CITAMP4F

Bit 19: CITAMP4F.

CITAMP5F

Bit 20: CITAMP5F.

CITAMP6F

Bit 21: CITAMP6F.

CITAMP7F

Bit 22: CITAMP7F.

BKP[0]R

TAMP backup register

Offset: 0x100, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BKP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BKP rw

Toggle fields

BKP

Bits 0-31: BKP.

BKP[1]R

TAMP backup register

Offset: 0x104, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BKP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BKP rw

Toggle fields

BKP

Bits 0-31: BKP.

BKP[2]R

TAMP backup register

Offset: 0x108, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BKP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BKP rw

Toggle fields

BKP

Bits 0-31: BKP.

BKP[3]R

TAMP backup register

Offset: 0x10c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BKP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BKP rw

Toggle fields

BKP

Bits 0-31: BKP.

BKP[4]R

TAMP backup register

Offset: 0x110, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BKP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BKP rw

Toggle fields

BKP

Bits 0-31: BKP.

TIM1

0x40012c00: Advanced-timers

52/191 fields covered.

Toggle register map

Offset	Name	31	30	29	28	27	26	25	24	23	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	CR1																				UIFREMAP		CKD		ARPE	CMS		DIR	OPM	URS	UDIS	CEN
0x4	CR2									MMS2				OIS[6]		OIS[5]		OIS[4]	OIS[3]N	OIS[3]	OIS[2]N	OIS[2]	OIS[1]N	OIS[1]	TI1S	MMS			CCDS	CCUS		CCPC
0x8	SMCR										TS					SMS_3	ETP	ECE	ETPS		ETF				MSM	TS_4			OCCS	SMS
0xc	DIER																	TDE	COMDE	CC[4]DE	CC[3]DE	CC[2]DE	CC[1]DE	UDE	BIE	TIE	COMIE	CC[4]IE	CC[3]IE	CC[2]IE	CC[1]IE	UIE
0x10	SR														CC6IF	CC5IF			SBIF	CC[4]OF	CC[3]OF	CC[2]OF	CC[1]OF	B2IF	BIF	TIF	COMIF	CC[4]IF	CC[3]IF	CC[2]IF	CC[1]IF	UIF
0x14	EGR																							B2G	BG	TG	COMG	CC[4]G	CC[3]G	CC[2]G	CC[1]G	UG
0x18	CCMR1_Input																IC[2]F				IC[2]PSC		CC[2]S		IC[1]F				IC[1]PSC		CC[1]S
0x18	CCMR1_Output								OC[2]M_3							OC[1]M_3	OC[2]CE	OC[2]M			OC[2]PE	OC[2]FE	CC[2]S		OC[1]CE	OC[1]M			OC[1]PE	OC[1]FE	CC[1]S
0x1c	CCMR2_Input																IC[4]F				IC[4]PSC		CC[4]S		IC[3]F				IC[3]PSC		CC[3]S
0x1c	CCMR2_Output								OC[4]M_3							OC[3]M_3	OC[4]CE	OC[4]M			OC[4]PE	OC[4]FE	CC[4]S		OC[3]CE	OC[3]M			OC[3]PE	OC[3]FE	CC[3]S
0x20	CCER										CC[6]P	CC[6]E			CC[5]P	CC[5]E	CC[4]NP		CC[4]P	CC[4]E	CC[3]NP	CC[3]NE	CC[3]P	CC[3]E	CC[2]NP	CC[2]NE	CC[2]P	CC[2]E	CC[1]NP	CC[1]NE	CC[1]P	CC[1]E
0x24	CNT	UIFCPY															CNT
0x28	PSC																PSC
0x2c	ARR																ARR
0x30	RCR																REP
0x34	CCR[1]																CCR
0x38	CCR[2]																CCR
0x3c	CCR[3]																CCR
0x40	CCR[4]																CCR
0x44	BDTR			BK2ID	BKBID	BK2DSRM	BKDSRM	BK2P	BK2E	BK2F			BKF				MOE	AOE	BKP	BKE	OSSR	OSSI	LOCK		DTG
0x48	DCR																			DBL								DBA
0x4c	DMAR																DMAB
0x50	OR1																															OCREF_CLR
0x54	CCMR3_Output								OC[6]M_3							OC[5]M_3	OC[6]CE	OC[6]M			OC[6]PE	OC[6]FE			OC[5]CE	OC[5]M			OC[5]PE	OC[5]FE
0x58	CCR5	GC5C3	GC5C2	GC5C1													CCR
0x5c	CCR6																CCR
0x60	AF1															ETRSEL	ETRSEL				BKCMP2P	BKCMP1P	BKINP							BKCMP2E	BKCMP1E	BKINE
0x64	AF2																				BK2CMP2P	BK2CMP1P	BK2INP	BK2DFBK0E						BK2CMP2E	BK2CMP1E	BK2INE
0x68	TISEL					TI4SEL3_0							TI3SEL3_0								TI2SEL3_0								TI1SEL3_0

Toggle registers

CR1

control register 1

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

8/9 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				UIFREMAP rw		CKD rw		ARPE rw	CMS rw		DIR rw	OPM rw	URS rw	UDIS rw	CEN rw

Toggle fields

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

Allowed values:
0: AnyEvent: Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request
1: CounterOnly: Only counter overflow/underflow generates an update interrupt or DMA request

OPM

Bit 3: One-pulse mode.

Allowed values:
0: Disabled: Counter is not stopped at update event
1: Enabled: Counter stops counting at the next update event (clearing the CEN bit)

DIR

Bit 4: Direction.

Allowed values:
0: Up: Counter used as upcounter
1: Down: Counter used as downcounter

CMS

Bits 5-6: Center-aligned mode selection.

Allowed values:
0: EdgeAligned: The counter counts up or down depending on the direction bit
1: CenterAligned1: The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting down.
2: CenterAligned2: The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting up.
3: CenterAligned3: The counter counts up and down alternatively. Output compare interrupt flags are set both when the counter is counting up or down.

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CKD

Bits 8-9: Clock division.

Allowed values:
0: Div1: t_DTS = t_CK_INT
1: Div2: t_DTS = 2 × t_CK_INT
2: Div4: t_DTS = 4 × t_CK_INT

UIFREMAP

Bit 11: UIF status bit remapping.

CR2

control register 2

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

9/15 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								MMS2 rw					OIS[6] rw		OIS[5] rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	OIS[4] rw	OIS[3]N rw	OIS[3] rw	OIS[2]N rw	OIS[2] rw	OIS[1]N rw	OIS[1] rw	TI1S rw	MMS rw			CCDS rw	CCUS rw		CCPC rw

Toggle fields

CCPC

Bit 0: Capture/compare preloaded control.

CCUS

Bit 2: Capture/compare control update selection.

CCDS

Bit 3: Capture/compare DMA selection.

MMS

Bits 4-6: Master mode selection.

TI1S

Bit 7: TI1 selection.

OIS[1]

Bit 8: Output Idle state (OC1 output).

Allowed values:
0: Reset: OCx=0 (after a dead-time if OCx(N) is implemented) when MOE=0
1: Set: OCx=1 (after a dead-time if OCx(N) is implemented) when MOE=0

OIS[1]N

Bit 9: Output Idle state (OC1N output).

Allowed values:
0: Reset: OCxN=0 after a dead-time when MOE=0
1: Set: OCxN=1 after a dead-time when MOE=0

OIS[2]

Bit 10: Output Idle state (OC2 output).

Allowed values:
0: Reset: OCx=0 (after a dead-time if OCx(N) is implemented) when MOE=0
1: Set: OCx=1 (after a dead-time if OCx(N) is implemented) when MOE=0

OIS[2]N

Bit 11: Output Idle state (OC2N output).

Allowed values:
0: Reset: OCxN=0 after a dead-time when MOE=0
1: Set: OCxN=1 after a dead-time when MOE=0

OIS[3]

Bit 12: Output Idle state (OC3 output).

Allowed values:
0: Reset: OCx=0 (after a dead-time if OCx(N) is implemented) when MOE=0
1: Set: OCx=1 (after a dead-time if OCx(N) is implemented) when MOE=0

OIS[3]N

Bit 13: Output Idle state (OC3N output).

Allowed values:
0: Reset: OCxN=0 after a dead-time when MOE=0
1: Set: OCxN=1 after a dead-time when MOE=0

OIS[4]

Bit 14: Output Idle state (OC4 output).

Allowed values:
0: Reset: OCx=0 (after a dead-time if OCx(N) is implemented) when MOE=0
1: Set: OCx=1 (after a dead-time if OCx(N) is implemented) when MOE=0

OIS[5]

Bit 16: Output Idle state (OC5 output).

Allowed values:
0: Reset: OCx=0 (after a dead-time if OCx(N) is implemented) when MOE=0
1: Set: OCx=1 (after a dead-time if OCx(N) is implemented) when MOE=0

OIS[6]

Bit 18: Output Idle state (OC6 output).

Allowed values:
0: Reset: OCx=0 (after a dead-time if OCx(N) is implemented) when MOE=0
1: Set: OCx=1 (after a dead-time if OCx(N) is implemented) when MOE=0

MMS2

Bits 20-23: Master mode selection 2.

SMCR

slave mode control register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

0/10 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
										TS rw					SMS_3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ETP rw	ECE rw	ETPS rw		ETF rw				MSM rw	TS_4 rw			OCCS rw	SMS rw

Toggle fields

SMS

Bits 0-2: Slave mode selection.

OCCS

Bit 3: OCREF clear selection.

TS_4

Bits 4-6: Trigger selection.

MSM

Bit 7: Master/Slave mode.

ETF

Bits 8-11: External trigger filter.

ETPS

Bits 12-13: External trigger prescaler.

ECE

Bit 14: External clock enable.

ETP

Bit 15: External trigger polarity.

SMS_3

Bit 16: Slave mode selection - bit 3.

TS

Bits 20-21: Trigger selection.

DIER

DMA/Interrupt enable register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

1/15 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	TDE rw	COMDE rw	CC[4]DE rw	CC[3]DE rw	CC[2]DE rw	CC[1]DE rw	UDE rw	BIE rw	TIE rw	COMIE rw	CC[4]IE rw	CC[3]IE rw	CC[2]IE rw	CC[1]IE rw	UIE rw

Toggle fields

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

CC[1]IE

Bit 1: Capture/Compare 1 interrupt enable.

CC[2]IE

Bit 2: Capture/Compare 2 interrupt enable.

CC[3]IE

Bit 3: Capture/Compare 3 interrupt enable.

CC[4]IE

Bit 4: Capture/Compare 4 interrupt enable.

COMIE

Bit 5: COM interrupt enable.

TIE

Bit 6: Trigger interrupt enable.

BIE

Bit 7: Break interrupt enable.

UDE

Bit 8: Update DMA request enable.

CC[1]DE

Bit 9: Capture/Compare 1 DMA request enable.

CC[2]DE

Bit 10: Capture/Compare 2 DMA request enable.

CC[3]DE

Bit 11: Capture/Compare 3 DMA request enable.

CC[4]DE

Bit 12: Capture/Compare 4 DMA request enable.

COMDE

Bit 13: COM DMA request enable.

TDE

Bit 14: Trigger DMA request enable.

SR

status register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

1/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
														CC6IF rw	CC5IF rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		SBIF rw	CC[4]OF rw	CC[3]OF rw	CC[2]OF rw	CC[1]OF rw	B2IF rw	BIF rw	TIF rw	COMIF rw	CC[4]IF rw	CC[3]IF rw	CC[2]IF rw	CC[1]IF rw	UIF rw

Toggle fields

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: NoUpdateOccurred: No update occurred
1: UpdatePending: Update interrupt pending

CC[1]IF

Bit 1: Capture/compare 1 interrupt flag.

CC[2]IF

Bit 2: Capture/compare 2 interrupt flag.

CC[3]IF

Bit 3: Capture/compare 3 interrupt flag.

CC[4]IF

Bit 4: Capture/compare 4 interrupt flag.

COMIF

Bit 5: COM interrupt flag.

TIF

Bit 6: Trigger interrupt flag.

BIF

Bit 7: Break interrupt flag.

B2IF

Bit 8: Break 2 interrupt flag.

CC[1]OF

Bit 9: Capture/Compare 1 overcapture flag.

CC[2]OF

Bit 10: Capture/Compare 2 overcapture flag.

CC[3]OF

Bit 11: Capture/Compare 3 overcapture flag.

CC[4]OF

Bit 12: Capture/Compare 4 overcapture flag.

SBIF

Bit 13: System Break interrupt flag.

CC5IF

Bit 16: Compare 5 interrupt flag.

CC6IF

Bit 17: Compare 6 interrupt flag.

EGR

event generation register

Offset: 0x14, size: 32, reset: 0x00000000, access: write-only

1/9 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							B2G w	BG w	TG w	COMG w	CC[4]G w	CC[3]G w	CC[2]G w	CC[1]G w	UG w

Toggle fields

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the registers.

CC[1]G

Bit 1: Capture/compare 1 generation.

CC[2]G

Bit 2: Capture/compare 2 generation.

CC[3]G

Bit 3: Capture/compare 3 generation.

CC[4]G

Bit 4: Capture/compare 4 generation.

COMG

Bit 5: Capture/Compare control update generation.

TG

Bit 6: Trigger generation.

BG

Bit 7: Break generation.

B2G

Bit 8: Break 2 generation.

CCMR1_Input

capture/compare mode register 1 (output mode)

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

0/6 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IC[2]F rw				IC[2]PSC rw		CC[2]S rw		IC[1]F rw				IC[1]PSC rw		CC[1]S rw

Toggle fields

CC[1]S

Bits 0-1: Capture/Compare 1 selection.

IC[1]PSC

Bits 2-3: Input capture 1 prescaler.

IC[1]F

Bits 4-7: Input capture 1 filter.

CC[2]S

Bits 8-9: Capture/Compare 2 selection.

IC[2]PSC

Bits 10-11: Input capture 2 prescaler.

IC[2]F

Bits 12-15: Input capture 2 filter.

CCMR1_Output

capture/compare mode register 1 (output mode)

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

4/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
							OC[2]M_3 rw								OC[1]M_3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OC[2]CE rw	OC[2]M rw			OC[2]PE rw	OC[2]FE rw	CC[2]S rw		OC[1]CE rw	OC[1]M rw			OC[1]PE rw	OC[1]FE rw	CC[1]S rw

Toggle fields

CC[1]S

Bits 0-1: Capture/Compare 1 selection.

OC[1]FE

Bit 2: Output compare 1 fast enable.

OC[1]PE

Bit 3: Output compare 1 preload enable.

OC[1]M

Bits 4-6: Output compare 1 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[1]CE

Bit 7: Output compare 1 clear enable.

CC[2]S

Bits 8-9: Capture/Compare 2 selection.

OC[2]FE

Bit 10: Output compare 2 fast enable.

OC[2]PE

Bit 11: Output compare 2 preload enable.

OC[2]M

Bits 12-14: Output compare 2 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[2]CE

Bit 15: Output compare 2 clear enable.

OC[1]M_3

Bit 16: Output compare 1 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

OC[2]M_3

Bit 24: Output compare 2 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

CCMR2_Input

capture/compare mode register 2 (output mode)

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

0/6 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IC[4]F rw				IC[4]PSC rw		CC[4]S rw		IC[3]F rw				IC[3]PSC rw		CC[3]S rw

Toggle fields

CC[3]S

Bits 0-1: Capture/Compare 3 selection.

IC[3]PSC

Bits 2-3: Input capture 3 prescaler.

IC[3]F

Bits 4-7: Input capture 3 filter.

CC[4]S

Bits 8-9: Capture/Compare 4 selection.

IC[4]PSC

Bits 10-11: Input capture 4 prescaler.

IC[4]F

Bits 12-15: Input capture 4 filter.

CCMR2_Output

capture/compare mode register 2 (output mode)

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

4/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
							OC[4]M_3 rw								OC[3]M_3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OC[4]CE rw	OC[4]M rw			OC[4]PE rw	OC[4]FE rw	CC[4]S rw		OC[3]CE rw	OC[3]M rw			OC[3]PE rw	OC[3]FE rw	CC[3]S rw

Toggle fields

CC[3]S

Bits 0-1: Capture/Compare 3 selection.

OC[3]FE

Bit 2: Output compare 3 fast enable.

OC[3]PE

Bit 3: Output compare 3 preload enable.

OC[3]M

Bits 4-6: Output compare 3 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[3]CE

Bit 7: Output compare 3 clear enable.

CC[4]S

Bits 8-9: Capture/Compare 4 selection.

OC[4]FE

Bit 10: Output compare 4 fast enable.

OC[4]PE

Bit 11: Output compare 4 preload enable.

OC[4]M

Bits 12-14: Output compare 4 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[4]CE

Bit 15: Output compare 4 clear enable.

OC[3]M_3

Bit 16: Output compare 3 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

OC[4]M_3

Bit 24: Output compare 4 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

CCER

capture/compare enable register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

0/19 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
										CC[6]P rw	CC[6]E rw			CC[5]P rw	CC[5]E rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CC[4]NP rw		CC[4]P rw	CC[4]E rw	CC[3]NP rw	CC[3]NE rw	CC[3]P rw	CC[3]E rw	CC[2]NP rw	CC[2]NE rw	CC[2]P rw	CC[2]E rw	CC[1]NP rw	CC[1]NE rw	CC[1]P rw	CC[1]E rw

Toggle fields

CC[1]E

Bit 0: Capture/Compare 1 output enable.

CC[1]P

Bit 1: Capture/Compare 1 output Polarity.

CC[1]NE

Bit 2: Capture/Compare 1 complementary output enable.

CC[1]NP

Bit 3: Capture/Compare 1 output Polarity.

CC[2]E

Bit 4: Capture/Compare 2 output enable.

CC[2]P

Bit 5: Capture/Compare 2 output Polarity.

CC[2]NE

Bit 6: Capture/Compare 2 complementary output enable.

CC[2]NP

Bit 7: Capture/Compare 2 output Polarity.

CC[3]E

Bit 8: Capture/Compare 3 output enable.

CC[3]P

Bit 9: Capture/Compare 3 output Polarity.

CC[3]NE

Bit 10: Capture/Compare 3 complementary output enable.

CC[3]NP

Bit 11: Capture/Compare 3 output Polarity.

CC[4]E

Bit 12: Capture/Compare 4 output enable.

CC[4]P

Bit 13: Capture/Compare 4 output Polarity.

CC[4]NP

Bit 15: Capture/Compare 4 output Polarity.

CC[5]E

Bit 16: Capture/Compare 5 output enable.

CC[5]P

Bit 17: Capture/Compare 5 output Polarity.

CC[6]E

Bit 20: Capture/Compare 6 output enable.

CC[6]P

Bit 21: Capture/Compare 6 output Polarity.

CNT

counter

Offset: 0x24, size: 32, reset: 0x00000000, access: Unspecified

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
UIFCPY r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CNT rw

Toggle fields

CNT

Bits 0-15: counter value.

Allowed values: 0x0-0xffff

UIFCPY

Bit 31: UIF copy.

PSC

prescaler

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PSC rw

Toggle fields

PSC

Bits 0-15: Prescaler value.

Allowed values: 0x0-0xffff

ARR

auto-reload register

Offset: 0x2c, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ARR rw

Toggle fields

ARR

Bits 0-15: Auto-reload value.

Allowed values: 0x0-0xffff

RCR

repetition counter register

Offset: 0x30, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
REP rw

Toggle fields

REP

Bits 0-15: Repetition counter value.

CCR[1]

capture/compare register

Offset: 0x34, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

Allowed values: 0x0-0xffff

CCR[2]

capture/compare register

Offset: 0x38, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

Allowed values: 0x0-0xffff

CCR[3]

capture/compare register

Offset: 0x3c, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

Allowed values: 0x0-0xffff

CCR[4]

capture/compare register

Offset: 0x40, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

Allowed values: 0x0-0xffff

BDTR

break and dead-time register

Offset: 0x44, size: 32, reset: 0x00000000, access: read-write

10/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
		BK2ID rw	BKBID rw	BK2DSRM rw	BKDSRM rw	BK2P rw	BK2E rw	BK2F rw				BKF rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MOE rw	AOE rw	BKP rw	BKE rw	OSSR rw	OSSI rw	LOCK rw		DTG rw

Toggle fields

DTG

Bits 0-7: Dead-time generator setup.

Allowed values: 0x0-0xff

LOCK

Bits 8-9: Lock configuration.

Allowed values:
0: Off: No bit is write protected
1: Level1: Any bits except MOE, OSSR, OSSI and LOCK in TIMx_BDTR register, OISx and OISxN bits in TIMx_CR2 register can no longer be written
2: Level2: LOCK Level 1 + CC Polarity bits (CCxP/CCxNP bits in TIMx_CCER register, as long as the related channel is configured in output through the CCxS bits) as well as OSSR and OSSI bits can no longer be written
3: Level3: LOCK Level 2 + CC Control bits (OCxM and OCxPE bits in TIMx_CCMRx registers, as long as the related channel is configured in output through the CCxS bits) can no longer be written

OSSI

Bit 10: Off-state selection for Idle mode.

Allowed values:
0: Disabled: When inactive, OC/OCN outputs are disabled
1: IdleLevel: When inactive, OC/OCN outputs are forced to idle level

OSSR

Bit 11: Off-state selection for Run mode.

Allowed values:
0: Disabled: When inactive, OC/OCN outputs are disabled
1: IdleLevel: When inactive, OC/OCN outputs are enabled with their inactive level

BKE

Bit 12: Break enable.

Allowed values:
0: Disabled: Break function x disabled
1: Enabled: Break function x disabled

BKP

Bit 13: Break polarity.

Allowed values:
0: ActiveLow: Break input BRKx is active low
1: ActiveHigh: Break input BRKx is active high

AOE

Bit 14: Automatic output enable.

Allowed values:
0: Manual: MOE can be set only by software
1: Automatic: MOE can be set by software or automatically at the next update event (if none of the break inputs BRK and BRK2 is active)

MOE

Bit 15: Main output enable.

Allowed values:
0: DisabledIdle: OC/OCN are disabled or forced idle depending on OSSI
1: Enabled: OC/OCN are enabled if CCxE/CCxNE are set

BKF

Bits 16-19: Break filter.

BK2F

Bits 20-23: Break 2 filter.

BK2E

Bit 24: Break 2 enable.

Allowed values:
0: Disabled: Break function x disabled
1: Enabled: Break function x disabled

BK2P

Bit 25: Break 2 polarity.

Allowed values:
0: ActiveLow: Break input BRKx is active low
1: ActiveHigh: Break input BRKx is active high

BKDSRM

Bit 26: Break Disarm.

BK2DSRM

Bit 27: Break2 Disarm.

BKBID

Bit 28: Break Bidirectional.

BK2ID

Bit 29: Break2 bidirectional.

DCR

DMA control register

Offset: 0x48, size: 32, reset: 0x00000000, access: read-write

0/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			DBL rw								DBA rw

Toggle fields

DBA

Bits 0-4: DMA base address.

DBL

Bits 8-12: DMA burst length.

DMAR

DMA address for full transfer

Offset: 0x4c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DMAB rw

Toggle fields

DMAB

Bits 0-15: DMA register for burst accesses.

OR1

option register 1

Offset: 0x50, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
															OCREF_CLR rw

Toggle fields

OCREF_CLR

Bit 0: Ocref_clr source selection.

CCMR3_Output

capture/compare mode register 2 (output mode)

Offset: 0x54, size: 32, reset: 0x00000000, access: read-write

4/10 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
							OC[6]M_3 rw								OC[5]M_3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OC[6]CE rw	OC[6]M rw			OC[6]PE rw	OC[6]FE rw			OC[5]CE rw	OC[5]M rw			OC[5]PE rw	OC[5]FE rw

Toggle fields

OC[5]FE

Bit 2: Output compare 5 fast enable.

OC[5]PE

Bit 3: Output compare 5 preload enable.

OC[5]M

Bits 4-6: Output compare 5 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[5]CE

Bit 7: Output compare 5 clear enable.

OC[6]FE

Bit 10: Output compare 6 fast enable.

OC[6]PE

Bit 11: Output compare 6 preload enable.

OC[6]M

Bits 12-14: Output compare 6 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[6]CE

Bit 15: Output compare 6 clear enable.

OC[5]M_3

Bit 16: Output compare 5 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

OC[6]M_3

Bit 24: Output compare 6 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

CCR5

capture/compare register

Offset: 0x58, size: 32, reset: 0x00000000, access: read-write

1/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
GC5C3 rw	GC5C2 rw	GC5C1 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

Allowed values: 0x0-0xffff

GC5C1

Bit 29: Group Channel 5 and Channel 1.

GC5C2

Bit 30: Group Channel 5 and Channel 2.

GC5C3

Bit 31: Group Channel 5 and Channel 3.

CCR6

capture/compare register

Offset: 0x5c, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

Allowed values: 0x0-0xffff

AF1

DMA address for full transfer

Offset: 0x60, size: 32, reset: 0x00000001, access: read-write

0/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															ETRSEL rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ETRSEL rw				BKCMP2P rw	BKCMP1P rw	BKINP rw							BKCMP2E rw	BKCMP1E rw	BKINE rw

Toggle fields

BKINE

Bit 0: BRK BKIN input enable.

BKCMP1E

Bit 1: BRK COMP1 enable.

BKCMP2E

Bit 2: BRK COMP2 enable.

BKINP

Bit 9: BRK BKIN input polarity.

BKCMP1P

Bit 10: BRK COMP1 input polarity.

BKCMP2P

Bit 11: BRK COMP2 input polarity.

ETRSEL

Bits 14-16: ETR source selection.

AF2

DMA address for full transfer

Offset: 0x64, size: 32, reset: 0x00000001, access: read-write

0/7 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				BK2CMP2P rw	BK2CMP1P rw	BK2INP rw	BK2DFBK0E rw						BK2CMP2E rw	BK2CMP1E rw	BK2INE rw

Toggle fields

BK2INE

Bit 0: BRK2 BKIN input enable.

BK2CMP1E

Bit 1: BRK2 COMP1 enable.

BK2CMP2E

Bit 2: BRK2 COMP2 enable.

BK2DFBK0E

Bit 8: BRK2 DFSDM_BREAK0 enable.

BK2INP

Bit 9: BRK2 BKIN input polarity.

BK2CMP1P

Bit 10: BRK2 COMP1 input polarity.

BK2CMP2P

Bit 11: BRK2 COMP2 input polarity.

TISEL

TIM1 timer input selection register

Offset: 0x68, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				TI4SEL3_0 rw								TI3SEL3_0 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				TI2SEL3_0 rw								TI1SEL3_0 rw

Toggle fields

TI1SEL3_0

Bits 0-3: selects TI1[0] to TI1[15] input.

TI2SEL3_0

Bits 8-11: selects TI2[0] to TI2[15] input.

TI3SEL3_0

Bits 16-19: selects TI3[0] to TI3[15] input.

TI4SEL3_0

Bits 24-27: selects TI4[0] to TI4[15] input.

TIM14

0x40002000: General purpose timers

11/32 fields covered.

Toggle register map

Offset	Name	31	16	15	11	9	7	6	3	2	1	0
0x0	CR1				UIFREMAP	CKD	ARPE		OPM	URS	UDIS	CEN
0xc	DIER										CC[1]IE	UIE
0x10	SR					CC[1]OF					CC[1]IF	UIF
0x14	EGR										CC[1]G	UG
0x18	CCMR1_Input						IC[1]F		IC[1]PSC		CC[1]S
0x18	CCMR1_Output		OC[1]M_3				OC[1]CE	OC[1]M	OC[1]PE	OC[1]FE	CC[1]S
0x20	CCER								CC[1]NP		CC[1]P	CC[1]E
0x24	CNT	UIFCPY		CNT
0x28	PSC			PSC
0x2c	ARR			ARR
0x34	CCR[1]			CCR
0x68	TISEL								TISEL

Toggle registers

CR1

control register 1

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

6/7 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				UIFREMAP rw		CKD rw		ARPE rw				OPM rw	URS rw	UDIS rw	CEN rw

Toggle fields

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

Allowed values:
0: AnyEvent: Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request
1: CounterOnly: Only counter overflow/underflow generates an update interrupt or DMA request

OPM

Bit 3: One-pulse mode.

Allowed values:
0: Disabled: Counter is not stopped at update event
1: Enabled: Counter stops counting at the next update event (clearing the CEN bit)

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CKD

Bits 8-9: Clock division.

Allowed values:
0: Div1: t_DTS = t_CK_INT
1: Div2: t_DTS = 2 × t_CK_INT
2: Div4: t_DTS = 4 × t_CK_INT

UIFREMAP

Bit 11: UIF status bit remapping.

DIER

DMA/Interrupt enable register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

1/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														CC[1]IE rw	UIE rw

Toggle fields

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

CC[1]IE

Bit 1: Capture/Compare 1 interrupt enable.

SR

status register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

1/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						CC[1]OF rw								CC[1]IF rw	UIF rw

Toggle fields

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: NoUpdateOccurred: No update occurred
1: UpdatePending: Update interrupt pending

CC[1]IF

Bit 1: Capture/compare 1 interrupt flag.

CC[1]OF

Bit 9: Capture/Compare 1 overcapture flag.

EGR

event generation register

Offset: 0x14, size: 32, reset: 0x00000000, access: write-only

1/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														CC[1]G w	UG w

Toggle fields

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the registers.

CC[1]G

Bit 1: Capture/compare 1 generation.

CCMR1_Input

capture/compare mode register 1 (input mode)

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

0/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								IC[1]F rw				IC[1]PSC rw		CC[1]S rw

Toggle fields

CC[1]S

Bits 0-1: Capture/Compare 1 selection.

IC[1]PSC

Bits 2-3: Input capture 1 prescaler.

IC[1]F

Bits 4-7: Input capture 1 filter.

CCMR1_Output

capture/compare mode register 1 (output mode)

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

1/6 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															OC[1]M_3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								OC[1]CE rw	OC[1]M rw			OC[1]PE rw	OC[1]FE rw	CC[1]S rw

Toggle fields

CC[1]S

Bits 0-1: Capture/Compare 1 selection.

OC[1]FE

Bit 2: Output compare 1 fast enable.

OC[1]PE

Bit 3: Output compare 1 preload enable.

OC[1]M

Bits 4-6: Output compare 1 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy
4: ForceInactive: OCyREF is forced low
5: ForceActive: OCyREF is forced high
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active
7: PwmMode2: Inversely to PwmMode1

OC[1]CE

Bit 7: Output compare 1 clear enable.

OC[1]M_3

Bit 16: Output compare 1 mode, bit 3.

CCER

capture/compare enable register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

0/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
												CC[1]NP rw		CC[1]P rw	CC[1]E rw

Toggle fields

CC[1]E

Bit 0: Capture/Compare 1 output enable.

CC[1]P

Bit 1: Capture/Compare 1 output Polarity.

CC[1]NP

Bit 3: Capture/Compare 1 output Polarity.

CNT

counter

Offset: 0x24, size: 32, reset: 0x00000000, access: read-write

0/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
UIFCPY rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CNT rw

Toggle fields

CNT

Bits 0-15: low counter value.

UIFCPY

Bit 31: UIF Copy.

PSC

prescaler

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PSC rw

Toggle fields

PSC

Bits 0-15: Prescaler value.

Allowed values: 0x0-0xffff

ARR

auto-reload register

Offset: 0x2c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ARR rw

Toggle fields

ARR

Bits 0-15: Low Auto-reload value.

CCR[1]

capture/compare register

Offset: 0x34, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

TISEL

TIM timer input selection register

Offset: 0x68, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
												TISEL rw

Toggle fields

TISEL

Bits 0-3: TI1[0] to TI1[15] input selection.

TIM16

0x40014400: General purpose timers

12/68 fields covered.

Toggle register map

Offset	Name	31	28	26	19	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	CR1										UIFREMAP		CKD		ARPE				OPM	URS	UDIS	CEN
0x4	CR2												OIS1N	OIS1					CCDS	CCUS		CCPC
0xc	DIER								COMDE				CC[1]DE	UDE	BIE		COMIE				CC[1]IE	UIE
0x10	SR												CC[1]OF		BIF		COMIF				CC[1]IF	UIF
0x14	EGR														BG		COMG				CC[1]G	UG
0x18	CCMR1_Input														IC[1]F				IC[1]PSC		CC[1]S
0x18	CCMR1_Output					OC1M_2										OC[1]M			OC[1]PE	OC[1]FE	CC[1]S
0x20	CCER																		CC[1]NP	CC[1]NE	CC[1]P	CC[1]E
0x24	CNT	UIFCPY					CNT
0x28	PSC						PSC
0x2c	ARR						ARR
0x30	RCR														REP
0x34	CCR[1]						CCR
0x44	BDTR		BKBID	BKDSRM	BKF		MOE	AOE	BKP	BKE	OSSR	OSSI	LOCK		DTG
0x48	DCR									DBL								DBA
0x4c	DMAR						DMAB
0x60	AF1										BKCMP2P	BKCMP1P	BKINP	BKDFBK1E						BKCMP2E	BKCMP1E	BKINE
0x68	TISEL																		TI1SEL

Toggle registers

CR1

control register 1

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

6/7 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				UIFREMAP rw		CKD rw		ARPE rw				OPM rw	URS rw	UDIS rw	CEN rw

Toggle fields

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

Allowed values:
0: AnyEvent: Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request
1: CounterOnly: Only counter overflow/underflow generates an update interrupt or DMA request

OPM

Bit 3: One-pulse mode.

Allowed values:
0: Disabled: Counter is not stopped at update event
1: Enabled: Counter stops counting at the next update event (clearing the CEN bit)

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CKD

Bits 8-9: Clock division.

Allowed values:
0: Div1: t_DTS = t_CK_INT
1: Div2: t_DTS = 2 × t_CK_INT
2: Div4: t_DTS = 4 × t_CK_INT

UIFREMAP

Bit 11: UIF status bit remapping.

CR2

control register 2

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

0/5 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						OIS1N rw	OIS1 rw					CCDS rw	CCUS rw		CCPC rw

Toggle fields

CCPC

Bit 0: Capture/compare preloaded control.

CCUS

Bit 2: Capture/compare control update selection.

CCDS

Bit 3: Capture/compare DMA selection.

OIS1

Bit 8: Output Idle state 1.

OIS1N

Bit 9: Output Idle state 1.

DIER

DMA/Interrupt enable register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

1/7 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		COMDE rw				CC[1]DE rw	UDE rw	BIE rw		COMIE rw				CC[1]IE rw	UIE rw

Toggle fields

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

CC[1]IE

Bit 1: Capture/Compare 1 interrupt enable.

COMIE

Bit 5: COM interrupt enable.

BIE

Bit 7: Break interrupt enable.

UDE

Bit 8: Update DMA request enable.

CC[1]DE

Bit 9: Capture/Compare 1 DMA request enable.

COMDE

Bit 13: COM DMA request enable.

SR

status register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

1/5 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						CC[1]OF rw		BIF rw		COMIF rw				CC[1]IF rw	UIF rw

Toggle fields

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: NoUpdateOccurred: No update occurred
1: UpdatePending: Update interrupt pending

CC[1]IF

Bit 1: Capture/compare 1 interrupt flag.

COMIF

Bit 5: COM interrupt flag.

BIF

Bit 7: Break interrupt flag.

CC[1]OF

Bit 9: Capture/Compare 1 overcapture flag.

EGR

event generation register

Offset: 0x14, size: 32, reset: 0x00000000, access: write-only

1/4 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								BG w		COMG w				CC[1]G w	UG w

Toggle fields

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the registers.

CC[1]G

Bit 1: Capture/compare 1 generation.

COMG

Bit 5: Capture/Compare control update generation.

BG

Bit 7: Break generation.

CCMR1_Input

capture/compare mode register 1 (input mode)

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

0/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								IC[1]F rw				IC[1]PSC rw		CC[1]S rw

Toggle fields

CC[1]S

Bits 0-1: Capture/Compare 1 selection.

IC[1]PSC

Bits 2-3: Input capture 1 prescaler.

IC[1]F

Bits 4-7: Input capture 1 filter.

CCMR1_Output

capture/compare mode register (output mode)

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

1/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															OC1M_2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
									OC[1]M rw			OC[1]PE rw	OC[1]FE rw	CC[1]S rw

Toggle fields

CC[1]S

Bits 0-1: Capture/Compare 1 selection.

OC[1]FE

Bit 2: Output compare 1 fast enable.

OC[1]PE

Bit 3: Output compare 1 preload enable.

OC[1]M

Bits 4-6: Output compare 1 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy
4: ForceInactive: OCyREF is forced low
5: ForceActive: OCyREF is forced high
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active
7: PwmMode2: Inversely to PwmMode1

OC1M_2

Bit 16: Output Compare 1 mode.

CCER

capture/compare enable register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
												CC[1]NP rw	CC[1]NE rw	CC[1]P rw	CC[1]E rw

Toggle fields

CC[1]E

Bit 0: Capture/Compare 1 output enable.

CC[1]P

Bit 1: Capture/Compare 1 output Polarity.

CC[1]NE

Bit 2: Capture/Compare 1 complementary output enable.

CC[1]NP

Bit 3: Capture/Compare 1 output Polarity.

CNT

counter

Offset: 0x24, size: 32, reset: 0x00000000, access: Unspecified

1/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
UIFCPY r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CNT rw

Toggle fields

CNT

Bits 0-15: counter value.

UIFCPY

Bit 31: UIF Copy.

PSC

prescaler

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PSC rw

Toggle fields

PSC

Bits 0-15: Prescaler value.

Allowed values: 0x0-0xffff

ARR

auto-reload register

Offset: 0x2c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ARR rw

Toggle fields

ARR

Bits 0-15: Auto-reload value.

RCR

repetition counter register

Offset: 0x30, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								REP rw

Toggle fields

REP

Bits 0-7: Repetition counter value.

CCR[1]

capture/compare register

Offset: 0x34, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

BDTR

break and dead-time register

Offset: 0x44, size: 32, reset: 0x00000000, access: read-write

0/11 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
			BKBID rw		BKDSRM rw							BKF rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MOE rw	AOE rw	BKP rw	BKE rw	OSSR rw	OSSI rw	LOCK rw		DTG rw

Toggle fields

DTG

Bits 0-7: Dead-time generator setup.

LOCK

Bits 8-9: Lock configuration.

OSSI

Bit 10: Off-state selection for Idle mode.

OSSR

Bit 11: Off-state selection for Run mode.

BKE

Bit 12: Break enable.

BKP

Bit 13: Break polarity.

AOE

Bit 14: Automatic output enable.

MOE

Bit 15: Main output enable.

BKF

Bits 16-19: Break filter.

BKDSRM

Bit 26: Break Disarm.

BKBID

Bit 28: Break Bidirectional.

DCR

DMA control register

Offset: 0x48, size: 32, reset: 0x00000000, access: read-write

0/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			DBL rw								DBA rw

Toggle fields

DBA

Bits 0-4: DMA base address.

DBL

Bits 8-12: DMA burst length.

DMAR

DMA address for full transfer

Offset: 0x4c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DMAB rw

Toggle fields

DMAB

Bits 0-15: DMA register for burst accesses.

AF1

TIM17 option register 1

Offset: 0x60, size: 32, reset: 0x00000000, access: read-write

0/7 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				BKCMP2P rw	BKCMP1P rw	BKINP rw	BKDFBK1E rw						BKCMP2E rw	BKCMP1E rw	BKINE rw

Toggle fields

BKINE

Bit 0: BRK BKIN input enable.

BKCMP1E

Bit 1: BRK COMP1 enable.

BKCMP2E

Bit 2: BRK COMP2 enable.

BKDFBK1E

Bit 8: BRK DFSDM_BREAK1 enable.

BKINP

Bit 9: BRK BKIN input polarity.

BKCMP1P

Bit 10: BRK COMP1 input polarity.

BKCMP2P

Bit 11: BRK COMP2 input polarit.

TISEL

input selection register

Offset: 0x68, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
												TI1SEL rw

Toggle fields

TI1SEL

Bits 0-3: selects input.

TIM17

0x40014800: General purpose timers

12/68 fields covered.

Toggle register map

Offset	Name	31	28	26	19	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	CR1										UIFREMAP		CKD		ARPE				OPM	URS	UDIS	CEN
0x4	CR2												OIS1N	OIS1					CCDS	CCUS		CCPC
0xc	DIER								COMDE				CC[1]DE	UDE	BIE		COMIE				CC[1]IE	UIE
0x10	SR												CC[1]OF		BIF		COMIF				CC[1]IF	UIF
0x14	EGR														BG		COMG				CC[1]G	UG
0x18	CCMR1_Input														IC[1]F				IC[1]PSC		CC[1]S
0x18	CCMR1_Output					OC1M_2										OC[1]M			OC[1]PE	OC[1]FE	CC[1]S
0x20	CCER																		CC[1]NP	CC[1]NE	CC[1]P	CC[1]E
0x24	CNT	UIFCPY					CNT
0x28	PSC						PSC
0x2c	ARR						ARR
0x30	RCR														REP
0x34	CCR[1]						CCR
0x44	BDTR		BKBID	BKDSRM	BKF		MOE	AOE	BKP	BKE	OSSR	OSSI	LOCK		DTG
0x48	DCR									DBL								DBA
0x4c	DMAR						DMAB
0x60	AF1										BKCMP2P	BKCMP1P	BKINP	BKDFBK1E						BKCMP2E	BKCMP1E	BKINE
0x68	TISEL																		TI1SEL

Toggle registers

CR1

control register 1

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

6/7 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				UIFREMAP rw		CKD rw		ARPE rw				OPM rw	URS rw	UDIS rw	CEN rw

Toggle fields

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

Allowed values:
0: AnyEvent: Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request
1: CounterOnly: Only counter overflow/underflow generates an update interrupt or DMA request

OPM

Bit 3: One-pulse mode.

Allowed values:
0: Disabled: Counter is not stopped at update event
1: Enabled: Counter stops counting at the next update event (clearing the CEN bit)

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CKD

Bits 8-9: Clock division.

Allowed values:
0: Div1: t_DTS = t_CK_INT
1: Div2: t_DTS = 2 × t_CK_INT
2: Div4: t_DTS = 4 × t_CK_INT

UIFREMAP

Bit 11: UIF status bit remapping.

CR2

control register 2

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

0/5 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						OIS1N rw	OIS1 rw					CCDS rw	CCUS rw		CCPC rw

Toggle fields

CCPC

Bit 0: Capture/compare preloaded control.

CCUS

Bit 2: Capture/compare control update selection.

CCDS

Bit 3: Capture/compare DMA selection.

OIS1

Bit 8: Output Idle state 1.

OIS1N

Bit 9: Output Idle state 1.

DIER

DMA/Interrupt enable register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

1/7 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		COMDE rw				CC[1]DE rw	UDE rw	BIE rw		COMIE rw				CC[1]IE rw	UIE rw

Toggle fields

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

CC[1]IE

Bit 1: Capture/Compare 1 interrupt enable.

COMIE

Bit 5: COM interrupt enable.

BIE

Bit 7: Break interrupt enable.

UDE

Bit 8: Update DMA request enable.

CC[1]DE

Bit 9: Capture/Compare 1 DMA request enable.

COMDE

Bit 13: COM DMA request enable.

SR

status register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

1/5 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						CC[1]OF rw		BIF rw		COMIF rw				CC[1]IF rw	UIF rw

Toggle fields

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: NoUpdateOccurred: No update occurred
1: UpdatePending: Update interrupt pending

CC[1]IF

Bit 1: Capture/compare 1 interrupt flag.

COMIF

Bit 5: COM interrupt flag.

BIF

Bit 7: Break interrupt flag.

CC[1]OF

Bit 9: Capture/Compare 1 overcapture flag.

EGR

event generation register

Offset: 0x14, size: 32, reset: 0x00000000, access: write-only

1/4 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								BG w		COMG w				CC[1]G w	UG w

Toggle fields

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the registers.

CC[1]G

Bit 1: Capture/compare 1 generation.

COMG

Bit 5: Capture/Compare control update generation.

BG

Bit 7: Break generation.

CCMR1_Input

capture/compare mode register 1 (input mode)

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

0/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								IC[1]F rw				IC[1]PSC rw		CC[1]S rw

Toggle fields

CC[1]S

Bits 0-1: Capture/Compare 1 selection.

IC[1]PSC

Bits 2-3: Input capture 1 prescaler.

IC[1]F

Bits 4-7: Input capture 1 filter.

CCMR1_Output

capture/compare mode register (output mode)

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

1/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															OC1M_2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
									OC[1]M rw			OC[1]PE rw	OC[1]FE rw	CC[1]S rw

Toggle fields

CC[1]S

Bits 0-1: Capture/Compare 1 selection.

OC[1]FE

Bit 2: Output compare 1 fast enable.

OC[1]PE

Bit 3: Output compare 1 preload enable.

OC[1]M

Bits 4-6: Output compare 1 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy
4: ForceInactive: OCyREF is forced low
5: ForceActive: OCyREF is forced high
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active
7: PwmMode2: Inversely to PwmMode1

OC1M_2

Bit 16: Output Compare 1 mode.

CCER

capture/compare enable register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

0/4 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
												CC[1]NP rw	CC[1]NE rw	CC[1]P rw	CC[1]E rw

Toggle fields

CC[1]E

Bit 0: Capture/Compare 1 output enable.

CC[1]P

Bit 1: Capture/Compare 1 output Polarity.

CC[1]NE

Bit 2: Capture/Compare 1 complementary output enable.

CC[1]NP

Bit 3: Capture/Compare 1 output Polarity.

CNT

counter

Offset: 0x24, size: 32, reset: 0x00000000, access: Unspecified

1/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
UIFCPY r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CNT rw

Toggle fields

CNT

Bits 0-15: counter value.

UIFCPY

Bit 31: UIF Copy.

PSC

prescaler

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PSC rw

Toggle fields

PSC

Bits 0-15: Prescaler value.

Allowed values: 0x0-0xffff

ARR

auto-reload register

Offset: 0x2c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ARR rw

Toggle fields

ARR

Bits 0-15: Auto-reload value.

RCR

repetition counter register

Offset: 0x30, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								REP rw

Toggle fields

REP

Bits 0-7: Repetition counter value.

CCR[1]

capture/compare register

Offset: 0x34, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare value.

BDTR

break and dead-time register

Offset: 0x44, size: 32, reset: 0x00000000, access: read-write

0/11 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
			BKBID rw		BKDSRM rw							BKF rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MOE rw	AOE rw	BKP rw	BKE rw	OSSR rw	OSSI rw	LOCK rw		DTG rw

Toggle fields

DTG

Bits 0-7: Dead-time generator setup.

LOCK

Bits 8-9: Lock configuration.

OSSI

Bit 10: Off-state selection for Idle mode.

OSSR

Bit 11: Off-state selection for Run mode.

BKE

Bit 12: Break enable.

BKP

Bit 13: Break polarity.

AOE

Bit 14: Automatic output enable.

MOE

Bit 15: Main output enable.

BKF

Bits 16-19: Break filter.

BKDSRM

Bit 26: Break Disarm.

BKBID

Bit 28: Break Bidirectional.

DCR

DMA control register

Offset: 0x48, size: 32, reset: 0x00000000, access: read-write

0/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			DBL rw								DBA rw

Toggle fields

DBA

Bits 0-4: DMA base address.

DBL

Bits 8-12: DMA burst length.

DMAR

DMA address for full transfer

Offset: 0x4c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DMAB rw

Toggle fields

DMAB

Bits 0-15: DMA register for burst accesses.

AF1

TIM17 option register 1

Offset: 0x60, size: 32, reset: 0x00000000, access: read-write

0/7 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				BKCMP2P rw	BKCMP1P rw	BKINP rw	BKDFBK1E rw						BKCMP2E rw	BKCMP1E rw	BKINE rw

Toggle fields

BKINE

Bit 0: BRK BKIN input enable.

BKCMP1E

Bit 1: BRK COMP1 enable.

BKCMP2E

Bit 2: BRK COMP2 enable.

BKDFBK1E

Bit 8: BRK DFSDM_BREAK1 enable.

BKINP

Bit 9: BRK BKIN input polarity.

BKCMP1P

Bit 10: BRK COMP1 input polarity.

BKCMP2P

Bit 11: BRK COMP2 input polarit.

TISEL

input selection register

Offset: 0x68, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
												TI1SEL rw

Toggle fields

TI1SEL

Bits 0-3: selects input.

TIM2

0x40000000: General-purpose-timers

20/112 fields covered.

Toggle register map

Offset	Name	31	24	21	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	CR1										UIFREMAP		CKD		ARPE	CMS		DIR	OPM	URS	UDIS	CEN
0x4	CR2														TI1S	MMS			CCDS
0x8	SMCR			TS_4_3		SMS_3	ETP	ECE	ETPS		ETF				MSM	TS			OCCS	SMS
0xc	DIER							TDE		CC[4]DE	CC[3]DE	CC[2]DE	CC[1]DE	UDE		TIE		CC[4]IE	CC[3]IE	CC[2]IE	CC[1]IE	UIE
0x10	SR									CC[4]OF	CC[3]OF	CC[2]OF	CC[1]OF			TIF		CC[4]IF	CC[3]IF	CC[2]IF	CC[1]IF	UIF
0x14	EGR															TG		CC[4]G	CC[3]G	CC[2]G	CC[1]G	UG
0x18	CCMR1_Input						IC[2]F				IC[2]PSC		CC[2]S		IC[1]F				IC[1]PSC		CC[1]S
0x18	CCMR1_Output		OC[2]M_3			OC[1]M_3	OC[2]CE	OC[2]M			OC[2]PE	OC[2]FE	CC[2]S		OC[1]CE	OC[1]M			OC[1]PE	OC[1]FE	CC[1]S
0x1c	CCMR2_Input						IC[4]F				IC[4]PSC		CC[4]S		IC[3]F				IC[3]PSC		CC[3]S
0x1c	CCMR2_Output		OC[4]M_3			OC[3]M_3	OC[4]CE	OC[4]M			OC[4]PE	OC[4]FE	CC[4]S		OC[3]CE	OC[3]M			OC[3]PE	OC[3]FE	CC[3]S
0x20	CCER						CC[4]NP		CC[4]P	CC[4]E	CC[3]NP		CC[3]P	CC[3]E	CC[2]NP		CC[2]P	CC[2]E	CC[1]NP		CC[1]P	CC[1]E
0x24	CNT	CNT					CNT
0x28	PSC						PSC
0x2c	ARR	ARR					ARR
0x34	CCR[1]	CCR					CCR
0x38	CCR[2]	CCR					CCR
0x3c	CCR[3]	CCR					CCR
0x40	CCR[4]	CCR					CCR
0x48	DCR									DBL								DBA
0x4c	DMAR						DMAB
0x50	OR1																					IOCREF_CLR
0x60	AF1				ETRSEL		ETRSEL
0x68	TISEL										TI2SEL								TI1SEL

Toggle registers

CR1

control register 1

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

8/9 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				UIFREMAP rw		CKD rw		ARPE rw	CMS rw		DIR rw	OPM rw	URS rw	UDIS rw	CEN rw

Toggle fields

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

Allowed values:
0: AnyEvent: Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request
1: CounterOnly: Only counter overflow/underflow generates an update interrupt or DMA request

OPM

Bit 3: One-pulse mode.

Allowed values:
0: Disabled: Counter is not stopped at update event
1: Enabled: Counter stops counting at the next update event (clearing the CEN bit)

DIR

Bit 4: Direction.

Allowed values:
0: Up: Counter used as upcounter
1: Down: Counter used as downcounter

CMS

Bits 5-6: Center-aligned mode selection.

Allowed values:
0: EdgeAligned: The counter counts up or down depending on the direction bit
1: CenterAligned1: The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting down.
2: CenterAligned2: The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting up.
3: CenterAligned3: The counter counts up and down alternatively. Output compare interrupt flags are set both when the counter is counting up or down.

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CKD

Bits 8-9: Clock division.

Allowed values:
0: Div1: t_DTS = t_CK_INT
1: Div2: t_DTS = 2 × t_CK_INT
2: Div4: t_DTS = 4 × t_CK_INT

UIFREMAP

Bit 11: UIF status bit remapping.

CR2

control register 2

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

0/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								TI1S rw	MMS rw			CCDS rw

Toggle fields

CCDS

Bit 3: Capture/compare DMA selection.

MMS

Bits 4-6: Master mode selection.

TI1S

Bit 7: TI1 selection.

SMCR

slave mode control register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

0/10 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
										TS_4_3 rw					SMS_3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ETP rw	ECE rw	ETPS rw		ETF rw				MSM rw	TS rw			OCCS rw	SMS rw

Toggle fields

SMS

Bits 0-2: Slave mode selection.

OCCS

Bit 3: OCREF clear selection.

TS

Bits 4-6: Trigger selection.

MSM

Bit 7: Master/Slave mode.

ETF

Bits 8-11: External trigger filter.

ETPS

Bits 12-13: External trigger prescaler.

ECE

Bit 14: External clock enable.

ETP

Bit 15: External trigger polarity.

SMS_3

Bit 16: Slave mode selection - bit 3.

TS_4_3

Bits 20-21: Trigger selection.

DIER

DMA/Interrupt enable register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

1/12 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	TDE rw		CC[4]DE rw	CC[3]DE rw	CC[2]DE rw	CC[1]DE rw	UDE rw		TIE rw		CC[4]IE rw	CC[3]IE rw	CC[2]IE rw	CC[1]IE rw	UIE rw

Toggle fields

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

CC[1]IE

Bit 1: Capture/Compare 1 interrupt enable.

CC[2]IE

Bit 2: Capture/Compare 2 interrupt enable.

CC[3]IE

Bit 3: Capture/Compare 3 interrupt enable.

CC[4]IE

Bit 4: Capture/Compare 4 interrupt enable.

TIE

Bit 6: Trigger interrupt enable.

UDE

Bit 8: Update DMA request enable.

CC[1]DE

Bit 9: Capture/Compare 1 DMA request enable.

CC[2]DE

Bit 10: Capture/Compare 2 DMA request enable.

CC[3]DE

Bit 11: Capture/Compare 3 DMA request enable.

CC[4]DE

Bit 12: Capture/Compare 4 DMA request enable.

TDE

Bit 14: Trigger DMA request enable.

SR

status register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

1/10 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			CC[4]OF rw	CC[3]OF rw	CC[2]OF rw	CC[1]OF rw			TIF rw		CC[4]IF rw	CC[3]IF rw	CC[2]IF rw	CC[1]IF rw	UIF rw

Toggle fields

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: NoUpdateOccurred: No update occurred
1: UpdatePending: Update interrupt pending

CC[1]IF

Bit 1: Capture/compare 1 interrupt flag.

CC[2]IF

Bit 2: Capture/compare 2 interrupt flag.

CC[3]IF

Bit 3: Capture/compare 3 interrupt flag.

CC[4]IF

Bit 4: Capture/compare 4 interrupt flag.

TIF

Bit 6: Trigger interrupt flag.

CC[1]OF

Bit 9: Capture/Compare 1 overcapture flag.

CC[2]OF

Bit 10: Capture/Compare 2 overcapture flag.

CC[3]OF

Bit 11: Capture/Compare 3 overcapture flag.

CC[4]OF

Bit 12: Capture/Compare 4 overcapture flag.

EGR

event generation register

Offset: 0x14, size: 32, reset: 0x00000000, access: write-only

1/6 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
									TG w		CC[4]G w	CC[3]G w	CC[2]G w	CC[1]G w	UG w

Toggle fields

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the registers.

CC[1]G

Bit 1: Capture/compare 1 generation.

CC[2]G

Bit 2: Capture/compare 2 generation.

CC[3]G

Bit 3: Capture/compare 3 generation.

CC[4]G

Bit 4: Capture/compare 4 generation.

TG

Bit 6: Trigger generation.

CCMR1_Input

capture/compare mode register 1 (input mode)

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

0/6 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IC[2]F rw				IC[2]PSC rw		CC[2]S rw		IC[1]F rw				IC[1]PSC rw		CC[1]S rw

Toggle fields

CC[1]S

Bits 0-1: Capture/Compare 1 selection.

IC[1]PSC

Bits 2-3: Input capture 1 prescaler.

IC[1]F

Bits 4-7: Input capture 1 filter.

CC[2]S

Bits 8-9: Capture/Compare 2 selection.

IC[2]PSC

Bits 10-11: Input capture 2 prescaler.

IC[2]F

Bits 12-15: Input capture 2 filter.

CCMR1_Output

capture/compare mode register 1 (output mode)

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

4/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
							OC[2]M_3 rw								OC[1]M_3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OC[2]CE rw	OC[2]M rw			OC[2]PE rw	OC[2]FE rw	CC[2]S rw		OC[1]CE rw	OC[1]M rw			OC[1]PE rw	OC[1]FE rw	CC[1]S rw

Toggle fields

CC[1]S

Bits 0-1: Capture/Compare 1 selection.

OC[1]FE

Bit 2: Output compare 1 fast enable.

OC[1]PE

Bit 3: Output compare 1 preload enable.

OC[1]M

Bits 4-6: Output compare 1 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[1]CE

Bit 7: Output compare 1 clear enable.

CC[2]S

Bits 8-9: Capture/Compare 2 selection.

OC[2]FE

Bit 10: Output compare 2 fast enable.

OC[2]PE

Bit 11: Output compare 2 preload enable.

OC[2]M

Bits 12-14: Output compare 2 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[2]CE

Bit 15: Output compare 2 clear enable.

OC[1]M_3

Bit 16: Output compare 1 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

OC[2]M_3

Bit 24: Output compare 2 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

CCMR2_Input

capture/compare mode register 2 (input mode)

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

0/6 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IC[4]F rw				IC[4]PSC rw		CC[4]S rw		IC[3]F rw				IC[3]PSC rw		CC[3]S rw

Toggle fields

CC[3]S

Bits 0-1: Capture/Compare 3 selection.

IC[3]PSC

Bits 2-3: Input capture 3 prescaler.

IC[3]F

Bits 4-7: Input capture 3 filter.

CC[4]S

Bits 8-9: Capture/Compare 4 selection.

IC[4]PSC

Bits 10-11: Input capture 4 prescaler.

IC[4]F

Bits 12-15: Input capture 4 filter.

CCMR2_Output

capture/compare mode register 2 (output mode)

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

4/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
							OC[4]M_3 rw								OC[3]M_3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OC[4]CE rw	OC[4]M rw			OC[4]PE rw	OC[4]FE rw	CC[4]S rw		OC[3]CE rw	OC[3]M rw			OC[3]PE rw	OC[3]FE rw	CC[3]S rw

Toggle fields

CC[3]S

Bits 0-1: Capture/Compare 3 selection.

OC[3]FE

Bit 2: Output compare 3 fast enable.

OC[3]PE

Bit 3: Output compare 3 preload enable.

OC[3]M

Bits 4-6: Output compare 3 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[3]CE

Bit 7: Output compare 3 clear enable.

CC[4]S

Bits 8-9: Capture/Compare 4 selection.

OC[4]FE

Bit 10: Output compare 4 fast enable.

OC[4]PE

Bit 11: Output compare 4 preload enable.

OC[4]M

Bits 12-14: Output compare 4 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[4]CE

Bit 15: Output compare 4 clear enable.

OC[3]M_3

Bit 16: Output compare 3 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

OC[4]M_3

Bit 24: Output compare 4 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

CCER

capture/compare enable register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

0/12 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CC[4]NP rw		CC[4]P rw	CC[4]E rw	CC[3]NP rw		CC[3]P rw	CC[3]E rw	CC[2]NP rw		CC[2]P rw	CC[2]E rw	CC[1]NP rw		CC[1]P rw	CC[1]E rw

Toggle fields

CC[1]E

Bit 0: Capture/Compare 1 output enable.

CC[1]P

Bit 1: Capture/Compare 1 output Polarity.

CC[1]NP

Bit 3: Capture/Compare 1 output Polarity.

CC[2]E

Bit 4: Capture/Compare 2 output enable.

CC[2]P

Bit 5: Capture/Compare 2 output Polarity.

CC[2]NP

Bit 7: Capture/Compare 2 output Polarity.

CC[3]E

Bit 8: Capture/Compare 3 output enable.

CC[3]P

Bit 9: Capture/Compare 3 output Polarity.

CC[3]NP

Bit 11: Capture/Compare 3 output Polarity.

CC[4]E

Bit 12: Capture/Compare 4 output enable.

CC[4]P

Bit 13: Capture/Compare 4 output Polarity.

CC[4]NP

Bit 15: Capture/Compare 4 output Polarity.

CNT

counter

Offset: 0x24, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
CNT rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CNT rw

Toggle fields

CNT

Bits 0-31: Counter value.

PSC

prescaler

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PSC rw

Toggle fields

PSC

Bits 0-15: Prescaler value.

Allowed values: 0x0-0xffff

ARR

auto-reload register

Offset: 0x2c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ARR rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ARR rw

Toggle fields

ARR

Bits 0-31: Auto-reload value.

CCR[1]

capture/compare register

Offset: 0x34, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
CCR rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-31: Capture/Compare value.

CCR[2]

capture/compare register

Offset: 0x38, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
CCR rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-31: Capture/Compare value.

CCR[3]

capture/compare register

Offset: 0x3c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
CCR rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-31: Capture/Compare value.

CCR[4]

capture/compare register

Offset: 0x40, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
CCR rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-31: Capture/Compare value.

DCR

DMA control register

Offset: 0x48, size: 32, reset: 0x00000000, access: read-write

0/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			DBL rw								DBA rw

Toggle fields

DBA

Bits 0-4: DMA base address.

DBL

Bits 8-12: DMA burst length.

DMAR

DMA address for full transfer

Offset: 0x4c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DMAB rw

Toggle fields

DMAB

Bits 0-15: DMA register for burst accesses.

OR1

TIM option register

Offset: 0x50, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
															IOCREF_CLR rw

Toggle fields

IOCREF_CLR

Bit 0: IOCREF_CLR.

AF1

TIM alternate function option register 1

Offset: 0x60, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
														ETRSEL rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ETRSEL rw

Toggle fields

ETRSEL

Bits 14-17: External trigger source selection.

TISEL

TIM alternate function option register 1

Offset: 0x68, size: 32, reset: 0x00000000, access: read-write

0/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				TI2SEL rw								TI1SEL rw

Toggle fields

TI1SEL

Bits 0-3: TI1SEL.

TI2SEL

Bits 8-11: TI2SEL.

TIM3

0x40000400: General-purpose-timers

20/112 fields covered.

Toggle register map

Offset	Name	24	21	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	CR1									UIFREMAP		CKD		ARPE	CMS		DIR	OPM	URS	UDIS	CEN
0x4	CR2													TI1S	MMS			CCDS
0x8	SMCR		TS_4_3		SMS_3	ETP	ECE	ETPS		ETF				MSM	TS			OCCS	SMS
0xc	DIER						TDE		CC[4]DE	CC[3]DE	CC[2]DE	CC[1]DE	UDE		TIE		CC[4]IE	CC[3]IE	CC[2]IE	CC[1]IE	UIE
0x10	SR								CC[4]OF	CC[3]OF	CC[2]OF	CC[1]OF			TIF		CC[4]IF	CC[3]IF	CC[2]IF	CC[1]IF	UIF
0x14	EGR														TG		CC[4]G	CC[3]G	CC[2]G	CC[1]G	UG
0x18	CCMR1_Input					IC[2]F				IC[2]PSC		CC[2]S		IC[1]F				IC[1]PSC		CC[1]S
0x18	CCMR1_Output	OC[2]M_3			OC[1]M_3	OC[2]CE	OC[2]M			OC[2]PE	OC[2]FE	CC[2]S		OC[1]CE	OC[1]M			OC[1]PE	OC[1]FE	CC[1]S
0x1c	CCMR2_Input					IC[4]F				IC[4]PSC		CC[4]S		IC[3]F				IC[3]PSC		CC[3]S
0x1c	CCMR2_Output	OC[4]M_3			OC[3]M_3	OC[4]CE	OC[4]M			OC[4]PE	OC[4]FE	CC[4]S		OC[3]CE	OC[3]M			OC[3]PE	OC[3]FE	CC[3]S
0x20	CCER					CC[4]NP		CC[4]P	CC[4]E	CC[3]NP		CC[3]P	CC[3]E	CC[2]NP		CC[2]P	CC[2]E	CC[1]NP		CC[1]P	CC[1]E
0x24	CNT					CNT
0x28	PSC					PSC
0x2c	ARR					ARR
0x34	CCR[1]					CCR
0x38	CCR[2]					CCR
0x3c	CCR[3]					CCR
0x40	CCR[4]					CCR
0x48	DCR								DBL								DBA
0x4c	DMAR					DMAB
0x50	OR1																				IOCREF_CLR
0x60	AF1			ETRSEL		ETRSEL
0x68	TISEL									TI2SEL								TI1SEL

Toggle registers

CR1

control register 1

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

8/9 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				UIFREMAP rw		CKD rw		ARPE rw	CMS rw		DIR rw	OPM rw	URS rw	UDIS rw	CEN rw

Toggle fields

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

Allowed values:
0: AnyEvent: Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request
1: CounterOnly: Only counter overflow/underflow generates an update interrupt or DMA request

OPM

Bit 3: One-pulse mode.

Allowed values:
0: Disabled: Counter is not stopped at update event
1: Enabled: Counter stops counting at the next update event (clearing the CEN bit)

DIR

Bit 4: Direction.

Allowed values:
0: Up: Counter used as upcounter
1: Down: Counter used as downcounter

CMS

Bits 5-6: Center-aligned mode selection.

Allowed values:
0: EdgeAligned: The counter counts up or down depending on the direction bit
1: CenterAligned1: The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting down.
2: CenterAligned2: The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting up.
3: CenterAligned3: The counter counts up and down alternatively. Output compare interrupt flags are set both when the counter is counting up or down.

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CKD

Bits 8-9: Clock division.

Allowed values:
0: Div1: t_DTS = t_CK_INT
1: Div2: t_DTS = 2 × t_CK_INT
2: Div4: t_DTS = 4 × t_CK_INT

UIFREMAP

Bit 11: UIF status bit remapping.

CR2

control register 2

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

0/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								TI1S rw	MMS rw			CCDS rw

Toggle fields

CCDS

Bit 3: Capture/compare DMA selection.

MMS

Bits 4-6: Master mode selection.

TI1S

Bit 7: TI1 selection.

SMCR

slave mode control register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

0/10 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
										TS_4_3 rw					SMS_3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ETP rw	ECE rw	ETPS rw		ETF rw				MSM rw	TS rw			OCCS rw	SMS rw

Toggle fields

SMS

Bits 0-2: Slave mode selection.

OCCS

Bit 3: OCREF clear selection.

TS

Bits 4-6: Trigger selection.

MSM

Bit 7: Master/Slave mode.

ETF

Bits 8-11: External trigger filter.

ETPS

Bits 12-13: External trigger prescaler.

ECE

Bit 14: External clock enable.

ETP

Bit 15: External trigger polarity.

SMS_3

Bit 16: Slave mode selection - bit 3.

TS_4_3

Bits 20-21: Trigger selection.

DIER

DMA/Interrupt enable register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

1/12 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	TDE rw		CC[4]DE rw	CC[3]DE rw	CC[2]DE rw	CC[1]DE rw	UDE rw		TIE rw		CC[4]IE rw	CC[3]IE rw	CC[2]IE rw	CC[1]IE rw	UIE rw

Toggle fields

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

CC[1]IE

Bit 1: Capture/Compare 1 interrupt enable.

CC[2]IE

Bit 2: Capture/Compare 2 interrupt enable.

CC[3]IE

Bit 3: Capture/Compare 3 interrupt enable.

CC[4]IE

Bit 4: Capture/Compare 4 interrupt enable.

TIE

Bit 6: Trigger interrupt enable.

UDE

Bit 8: Update DMA request enable.

CC[1]DE

Bit 9: Capture/Compare 1 DMA request enable.

CC[2]DE

Bit 10: Capture/Compare 2 DMA request enable.

CC[3]DE

Bit 11: Capture/Compare 3 DMA request enable.

CC[4]DE

Bit 12: Capture/Compare 4 DMA request enable.

TDE

Bit 14: Trigger DMA request enable.

SR

status register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

1/10 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			CC[4]OF rw	CC[3]OF rw	CC[2]OF rw	CC[1]OF rw			TIF rw		CC[4]IF rw	CC[3]IF rw	CC[2]IF rw	CC[1]IF rw	UIF rw

Toggle fields

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: NoUpdateOccurred: No update occurred
1: UpdatePending: Update interrupt pending

CC[1]IF

Bit 1: Capture/compare 1 interrupt flag.

CC[2]IF

Bit 2: Capture/compare 2 interrupt flag.

CC[3]IF

Bit 3: Capture/compare 3 interrupt flag.

CC[4]IF

Bit 4: Capture/compare 4 interrupt flag.

TIF

Bit 6: Trigger interrupt flag.

CC[1]OF

Bit 9: Capture/Compare 1 overcapture flag.

CC[2]OF

Bit 10: Capture/Compare 2 overcapture flag.

CC[3]OF

Bit 11: Capture/Compare 3 overcapture flag.

CC[4]OF

Bit 12: Capture/Compare 4 overcapture flag.

EGR

event generation register

Offset: 0x14, size: 32, reset: 0x00000000, access: write-only

1/6 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
									TG w		CC[4]G w	CC[3]G w	CC[2]G w	CC[1]G w	UG w

Toggle fields

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the registers.

CC[1]G

Bit 1: Capture/compare 1 generation.

CC[2]G

Bit 2: Capture/compare 2 generation.

CC[3]G

Bit 3: Capture/compare 3 generation.

CC[4]G

Bit 4: Capture/compare 4 generation.

TG

Bit 6: Trigger generation.

CCMR1_Input

capture/compare mode register 1 (input mode)

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

0/6 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IC[2]F rw				IC[2]PSC rw		CC[2]S rw		IC[1]F rw				IC[1]PSC rw		CC[1]S rw

Toggle fields

CC[1]S

Bits 0-1: Capture/Compare 1 selection.

IC[1]PSC

Bits 2-3: Input capture 1 prescaler.

IC[1]F

Bits 4-7: Input capture 1 filter.

CC[2]S

Bits 8-9: Capture/Compare 2 selection.

IC[2]PSC

Bits 10-11: Input capture 2 prescaler.

IC[2]F

Bits 12-15: Input capture 2 filter.

CCMR1_Output

capture/compare mode register 1 (output mode)

Offset: 0x18, size: 32, reset: 0x00000000, access: read-write

4/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
							OC[2]M_3 rw								OC[1]M_3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OC[2]CE rw	OC[2]M rw			OC[2]PE rw	OC[2]FE rw	CC[2]S rw		OC[1]CE rw	OC[1]M rw			OC[1]PE rw	OC[1]FE rw	CC[1]S rw

Toggle fields

CC[1]S

Bits 0-1: Capture/Compare 1 selection.

OC[1]FE

Bit 2: Output compare 1 fast enable.

OC[1]PE

Bit 3: Output compare 1 preload enable.

OC[1]M

Bits 4-6: Output compare 1 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[1]CE

Bit 7: Output compare 1 clear enable.

CC[2]S

Bits 8-9: Capture/Compare 2 selection.

OC[2]FE

Bit 10: Output compare 2 fast enable.

OC[2]PE

Bit 11: Output compare 2 preload enable.

OC[2]M

Bits 12-14: Output compare 2 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[2]CE

Bit 15: Output compare 2 clear enable.

OC[1]M_3

Bit 16: Output compare 1 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

OC[2]M_3

Bit 24: Output compare 2 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

CCMR2_Input

capture/compare mode register 2 (input mode)

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

0/6 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IC[4]F rw				IC[4]PSC rw		CC[4]S rw		IC[3]F rw				IC[3]PSC rw		CC[3]S rw

Toggle fields

CC[3]S

Bits 0-1: Capture/Compare 3 selection.

IC[3]PSC

Bits 2-3: Input capture 3 prescaler.

IC[3]F

Bits 4-7: Input capture 3 filter.

CC[4]S

Bits 8-9: Capture/Compare 4 selection.

IC[4]PSC

Bits 10-11: Input capture 4 prescaler.

IC[4]F

Bits 12-15: Input capture 4 filter.

CCMR2_Output

capture/compare mode register 2 (output mode)

Offset: 0x1c, size: 32, reset: 0x00000000, access: read-write

4/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
							OC[4]M_3 rw								OC[3]M_3 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OC[4]CE rw	OC[4]M rw			OC[4]PE rw	OC[4]FE rw	CC[4]S rw		OC[3]CE rw	OC[3]M rw			OC[3]PE rw	OC[3]FE rw	CC[3]S rw

Toggle fields

CC[3]S

Bits 0-1: Capture/Compare 3 selection.

OC[3]FE

Bit 2: Output compare 3 fast enable.

OC[3]PE

Bit 3: Output compare 3 preload enable.

OC[3]M

Bits 4-6: Output compare 3 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[3]CE

Bit 7: Output compare 3 clear enable.

CC[4]S

Bits 8-9: Capture/Compare 4 selection.

OC[4]FE

Bit 10: Output compare 4 fast enable.

OC[4]PE

Bit 11: Output compare 4 preload enable.

OC[4]M

Bits 12-14: Output compare 4 mode.

Allowed values:
0: Frozen: The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive
1: ActiveOnMatch: Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1
2: InactiveOnMatch: Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved
3: Toggle: OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved
4: ForceInactive: OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF
5: ForceActive: OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF
6: PwmMode1: In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down
7: PwmMode2: Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1

OC[4]CE

Bit 15: Output compare 4 clear enable.

OC[3]M_3

Bit 16: Output compare 3 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

OC[4]M_3

Bit 24: Output compare 4 mode, bit 3.

Allowed values:
0: Normal: Normal output compare mode (modes 0-7)
1: Extended: Extended output compare mode (modes 7-15)

CCER

capture/compare enable register

Offset: 0x20, size: 32, reset: 0x00000000, access: read-write

0/12 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CC[4]NP rw		CC[4]P rw	CC[4]E rw	CC[3]NP rw		CC[3]P rw	CC[3]E rw	CC[2]NP rw		CC[2]P rw	CC[2]E rw	CC[1]NP rw		CC[1]P rw	CC[1]E rw

Toggle fields

CC[1]E

Bit 0: Capture/Compare 1 output enable.

CC[1]P

Bit 1: Capture/Compare 1 output Polarity.

CC[1]NP

Bit 3: Capture/Compare 1 output Polarity.

CC[2]E

Bit 4: Capture/Compare 2 output enable.

CC[2]P

Bit 5: Capture/Compare 2 output Polarity.

CC[2]NP

Bit 7: Capture/Compare 2 output Polarity.

CC[3]E

Bit 8: Capture/Compare 3 output enable.

CC[3]P

Bit 9: Capture/Compare 3 output Polarity.

CC[3]NP

Bit 11: Capture/Compare 3 output Polarity.

CC[4]E

Bit 12: Capture/Compare 4 output enable.

CC[4]P

Bit 13: Capture/Compare 4 output Polarity.

CC[4]NP

Bit 15: Capture/Compare 4 output Polarity.

CNT

counter

Offset: 0x24, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CNT rw

Toggle fields

CNT

Bits 0-15: Counter value.

PSC

prescaler

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PSC rw

Toggle fields

PSC

Bits 0-15: Prescaler value.

Allowed values: 0x0-0xffff

ARR

auto-reload register

Offset: 0x2c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ARR rw

Toggle fields

ARR

Bits 0-15: Auto-reload value.

CCR[1]

capture/compare register

Offset: 0x34, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare 1 value.

CCR[2]

capture/compare register

Offset: 0x38, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare 1 value.

CCR[3]

capture/compare register

Offset: 0x3c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare 1 value.

CCR[4]

capture/compare register

Offset: 0x40, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle fields

CCR

Bits 0-15: Capture/Compare 1 value.

DCR

DMA control register

Offset: 0x48, size: 32, reset: 0x00000000, access: read-write

0/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			DBL rw								DBA rw

Toggle fields

DBA

Bits 0-4: DMA base address.

DBL

Bits 8-12: DMA burst length.

DMAR

DMA address for full transfer

Offset: 0x4c, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DMAB rw

Toggle fields

DMAB

Bits 0-15: DMA register for burst accesses.

OR1

TIM option register

Offset: 0x50, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
															IOCREF_CLR rw

Toggle fields

IOCREF_CLR

Bit 0: IOCREF_CLR.

AF1

TIM alternate function option register 1

Offset: 0x60, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
														ETRSEL rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ETRSEL rw

Toggle fields

ETRSEL

Bits 14-17: External trigger source selection.

TISEL

TIM alternate function option register 1

Offset: 0x68, size: 32, reset: 0x00000000, access: read-write

0/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				TI2SEL rw								TI1SEL rw

Toggle fields

TI1SEL

Bits 0-3: TI1SEL.

TI2SEL

Bits 8-11: TI2SEL.

USART1

0x40013800: Universal synchronous asynchronous receiver transmitter

124/124 fields covered.

Toggle register map

Offset	Name	31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	CR1	RXFFIE	TXFEIE	FIFOEN	M1	EOBIE	RTOIE	DEAT					DEDT					OVER8	CMIE	MME	M0	WAKE	PCE	PS	PEIE	TXEIE	TCIE	RXNEIE	IDLEIE	TE	RE	UESM	UE
0x4	CR2	ADD								RTOEN	ABRMOD		ABREN	MSBFIRST	DATAINV	TXINV	RXINV	SWAP	LINEN	STOP		CLKEN	CPOL	CPHA	LBCL		LBDIE	LBDL	ADDM7	DIS_NSS			SLVEN
0x8	CR3	TXFTCFG			RXFTIE	RXFTCFG			TCBGTIE	TXFTIE	WUFIE	WUS		SCARCNT				DEP	DEM	DDRE	OVRDIS	ONEBIT	CTSIE	CTSE	RTSE	DMAT	DMAR	SCEN	NACK	HDSEL	IRLP	IREN	EIE
0xc	BRR																	BRR
0x10	GTPR																	GT								PSC
0x14	RTOR	BLEN								RTO								RTO
0x18	RQR																												TXFRQ	RXFRQ	MMRQ	SBKRQ	ABRRQ
0x1c	ISR					TXFT	RXFT	TCBGT	RXFF	TXFE	REACK	TEACK	WUF	RWU	SBKF	CMF	BUSY	ABRF	ABRE	UDR	EOBF	RTOF	CTS	CTSIF	LBDF	TXE	TC	RXNE	IDLE	ORE	NF	FE	PE
0x20	ICR												WUCF			CMCF				UDRCF	EOBCF	RTOCF		CTSCF	LBDCF	TCBGTCF	TCCF	TXFECF	IDLECF	ORECF	NCF	FECF	PECF
0x24	RDR																								RDR
0x28	TDR																								TDR
0x2c	PRESC																													PRESCALER

Toggle registers

CR1

Control register 1

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

24/24 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
RXFFIE rw	TXFEIE rw	FIFOEN rw	M1 rw	EOBIE rw	RTOIE rw	DEAT rw					DEDT rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OVER8 rw	CMIE rw	MME rw	M0 rw	WAKE rw	PCE rw	PS rw	PEIE rw	TXEIE rw	TCIE rw	RXNEIE rw	IDLEIE rw	TE rw	RE rw	UESM rw	UE rw

Toggle fields

UE

Bit 0: USART enable.

Allowed values:
0: Disabled: UART is disabled
1: Enabled: UART is enabled

UESM

Bit 1: USART enable in Stop mode.

Allowed values:
0: Disabled: USART not able to wake up the MCU from Stop mode
1: Enabled: USART able to wake up the MCU from Stop mode

RE

Bit 2: Receiver enable.

Allowed values:
0: Disabled: Receiver is disabled
1: Enabled: Receiver is enabled

TE

Bit 3: Transmitter enable.

Allowed values:
0: Disabled: Transmitter is disabled
1: Enabled: Transmitter is enabled

IDLEIE

Bit 4: IDLE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever IDLE=1 in the ISR register

RXNEIE

Bit 5: RXNE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever ORE=1 or RXNE=1 in the ISR register

TCIE

Bit 6: Transmission complete interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever TC=1 in the ISR register

TXEIE

Bit 7: interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever TXE=1 in the ISR register

PEIE

Bit 8: PE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever PE=1 in the ISR register

PS

Bit 9: Parity selection.

Allowed values:
0: Even: Even parity
1: Odd: Odd parity

PCE

Bit 10: Parity control enable.

Allowed values:
0: Disabled: Parity control disabled
1: Enabled: Parity control enabled

WAKE

Bit 11: Receiver wakeup method.

Allowed values:
0: Idle: Idle line
1: Address: Address mask

M0

Bit 12: Word length.

Allowed values:
0: Bit8: 1 start bit, 8 data bits, n stop bits
1: Bit9: 1 start bit, 9 data bits, n stop bits

MME

Bit 13: Mute mode enable.

Allowed values:
0: Disabled: Receiver in active mode permanently
1: Enabled: Receiver can switch between mute mode and active mode

CMIE

Bit 14: Character match interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated when the CMF bit is set in the ISR register

OVER8

Bit 15: Oversampling mode.

Allowed values:
0: Oversampling16: Oversampling by 16
1: Oversampling8: Oversampling by 8

DEDT

Bits 16-20: DEDT.

Allowed values: 0x0-0x1f

DEAT

Bits 21-25: DEAT.

Allowed values: 0x0-0x1f

RTOIE

Bit 26: Receiver timeout interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An USART interrupt is generated when the RTOF bit is set in the ISR register

EOBIE

Bit 27: End of Block interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: A USART interrupt is generated when the EOBF flag is set in the ISR register

M1

Bit 28: Word length.

Allowed values:
0: M0: Use M0 to set the data bits
1: Bit7: 1 start bit, 7 data bits, n stop bits

FIFOEN

Bit 29: FIFO mode enable.

Allowed values:
0: Disabled: FIFO mode is disabled
1: Enabled: FIFO mode is enabled

TXFEIE

Bit 30: TXFIFO empty interrupt enable.

Allowed values:
0: Disabled: Interrupt inhibited
1: Enabled: USART interrupt generated when TXFE = 1 in the USART_ISR register

RXFFIE

Bit 31: RXFIFO Full interrupt enable.

Allowed values:
0: Disabled: Interrupt inhibited
1: Enabled: USART interrupt generated when RXFF = 1 in the USART_ISR register

CR2

Control register 2

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

20/20 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ADD rw								RTOEN rw	ABRMOD rw		ABREN rw	MSBFIRST rw	DATAINV rw	TXINV rw	RXINV rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SWAP rw	LINEN rw	STOP rw		CLKEN rw	CPOL rw	CPHA rw	LBCL rw		LBDIE rw	LBDL rw	ADDM7 rw	DIS_NSS rw			SLVEN rw

Toggle fields

SLVEN

Bit 0: Synchronous Slave mode enable.

Allowed values:
0: Disabled: Slave mode disabled
1: Enabled: Slave mode enabled

DIS_NSS

Bit 3: When the DSI_NSS bit is set, the NSS pin input will be ignored.

Allowed values:
0: Disabled: SPI slave selection depends on NSS input pin
1: Enabled: SPI slave is always selected and NSS input pin is ignored

ADDM7

Bit 4: 7-bit Address Detection/4-bit Address Detection.

Allowed values:
0: Bit4: 4-bit address detection
1: Bit7: 7-bit address detection

LBDL

Bit 5: LIN break detection length.

Allowed values:
0: Bit10: 10-bit break detection
1: Bit11: 11-bit break detection

LBDIE

Bit 6: LIN break detection interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated whenever LBDF=1 in the ISR register

LBCL

Bit 8: Last bit clock pulse.

Allowed values:
0: NotOutput: The clock pulse of the last data bit is not output to the CK pin
1: Output: The clock pulse of the last data bit is output to the CK pin

CPHA

Bit 9: Clock phase.

Allowed values:
0: First: The first clock transition is the first data capture edge
1: Second: The second clock transition is the first data capture edge

CPOL

Bit 10: Clock polarity.

Allowed values:
0: Low: Steady low value on CK pin outside transmission window
1: High: Steady high value on CK pin outside transmission window

CLKEN

Bit 11: Clock enable.

Allowed values:
0: Disabled: CK pin disabled
1: Enabled: CK pin enabled

STOP

Bits 12-13: STOP bits.

Allowed values:
0: Stop1: 1 stop bit
1: Stop0p5: 0.5 stop bit
2: Stop2: 2 stop bit
3: Stop1p5: 1.5 stop bit

LINEN

Bit 14: LIN mode enable.

Allowed values:
0: Disabled: LIN mode disabled
1: Enabled: LIN mode enabled

SWAP

Bit 15: Swap TX/RX pins.

Allowed values:
0: Standard: TX/RX pins are used as defined in standard pinout
1: Swapped: The TX and RX pins functions are swapped

RXINV

Bit 16: RX pin active level inversion.

Allowed values:
0: Standard: RX pin signal works using the standard logic levels
1: Inverted: RX pin signal values are inverted

TXINV

Bit 17: TX pin active level inversion.

Allowed values:
0: Standard: TX pin signal works using the standard logic levels
1: Inverted: TX pin signal values are inverted

DATAINV

Bit 18: Binary data inversion.

Allowed values:
0: Positive: Logical data from the data register are send/received in positive/direct logic
1: Negative: Logical data from the data register are send/received in negative/inverse logic

MSBFIRST

Bit 19: Most significant bit first.

Allowed values:
0: LSB: data is transmitted/received with data bit 0 first, following the start bit
1: MSB: data is transmitted/received with MSB (bit 7/8/9) first, following the start bit

ABREN

Bit 20: Auto baud rate enable.

Allowed values:
0: Disabled: Auto baud rate detection is disabled
1: Enabled: Auto baud rate detection is enabled

ABRMOD

Bits 21-22: Auto baud rate mode.

Allowed values:
0: Start: Measurement of the start bit is used to detect the baud rate
1: Edge: Falling edge to falling edge measurement
2: Frame7F: 0x7F frame detection
3: Frame55: 0x55 frame detection

RTOEN

Bit 23: Receiver timeout enable.

Allowed values:
0: Disabled: Receiver timeout feature disabled
1: Enabled: Receiver timeout feature enabled

ADD

Bits 24-31: Address of the USART node.

Allowed values: 0x0-0xff

CR3

Control register 3

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

24/24 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
TXFTCFG rw			RXFTIE rw	RXFTCFG rw			TCBGTIE rw	TXFTIE rw	WUFIE rw	WUS rw		SCARCNT rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DEP rw	DEM rw	DDRE rw	OVRDIS rw	ONEBIT rw	CTSIE rw	CTSE rw	RTSE rw	DMAT rw	DMAR rw	SCEN rw	NACK rw	HDSEL rw	IRLP rw	IREN rw	EIE rw

Toggle fields

EIE

Bit 0: Error interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated when FE=1 or ORE=1 or NF=1 in the ISR register

IREN

Bit 1: Ir mode enable.

Allowed values:
0: Disabled: IrDA disabled
1: Enabled: IrDA enabled

IRLP

Bit 2: Ir low-power.

Allowed values:
0: Normal: Normal mode
1: LowPower: Low-power mode

HDSEL

Bit 3: Half-duplex selection.

Allowed values:
0: NotSelected: Half duplex mode is not selected
1: Selected: Half duplex mode is selected

NACK

Bit 4: Smartcard NACK enable.

Allowed values:
0: Disabled: NACK transmission in case of parity error is disabled
1: Enabled: NACK transmission during parity error is enabled

SCEN

Bit 5: Smartcard mode enable.

Allowed values:
0: Disabled: Smartcard Mode disabled
1: Enabled: Smartcard Mode enabled

DMAR

Bit 6: DMA enable receiver.

Allowed values:
0: Disabled: DMA mode is disabled for reception
1: Enabled: DMA mode is enabled for reception

DMAT

Bit 7: DMA enable transmitter.

Allowed values:
0: Disabled: DMA mode is disabled for transmission
1: Enabled: DMA mode is enabled for transmission

RTSE

Bit 8: RTS enable.

Allowed values:
0: Disabled: RTS hardware flow control disabled
1: Enabled: RTS output enabled, data is only requested when there is space in the receive buffer

CTSE

Bit 9: CTS enable.

Allowed values:
0: Disabled: CTS hardware flow control disabled
1: Enabled: CTS mode enabled, data is only transmitted when the CTS input is asserted

CTSIE

Bit 10: CTS interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated whenever CTSIF=1 in the ISR register

ONEBIT

Bit 11: One sample bit method enable.

Allowed values:
0: Sample3: Three sample bit method
1: Sample1: One sample bit method

OVRDIS

Bit 12: Overrun Disable.

Allowed values:
0: Enabled: Overrun Error Flag, ORE, is set when received data is not read before receiving new data
1: Disabled: Overrun functionality is disabled. If new data is received while the RXNE flag is still set the ORE flag is not set and the new received data overwrites the previous content of the RDR register

DDRE

Bit 13: DMA Disable on Reception Error.

Allowed values:
0: NotDisabled: DMA is not disabled in case of reception error
1: Disabled: DMA is disabled following a reception error

DEM

Bit 14: Driver enable mode.

Allowed values:
0: Disabled: DE function is disabled
1: Enabled: The DE signal is output on the RTS pin

DEP

Bit 15: Driver enable polarity selection.

Allowed values:
0: High: DE signal is active high
1: Low: DE signal is active low

SCARCNT

Bits 17-19: Smartcard auto-retry count.

Allowed values: 0x0-0x7

WUS

Bits 20-21: Wakeup from Stop mode interrupt flag selection.

Allowed values:
0: Address: WUF active on address match
2: Start: WuF active on Start bit detection
3: RXNE: WUF active on RXNE

WUFIE

Bit 22: Wakeup from Stop mode interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An USART interrupt is generated whenever WUF=1 in the ISR register

TXFTIE

Bit 23: threshold interrupt enable.

Allowed values:
0: Disabled: Interrupt inhibited
1: Enabled: USART interrupt generated when Transmit FIFO reaches the threshold programmed in TXFTCFG

TCBGTIE

Bit 24: Tr Complete before guard time, interrupt enable.

Allowed values:
0: Disabled: Interrupt inhibited
1: Enabled: USART interrupt generated whenever TCBGT=1 in the USART_ISR register

RXFTCFG

Bits 25-27: Receive FIFO threshold configuration.

Allowed values:
0: Depth_1_8: RXFIFO reaches 1/8 of its depth
1: Depth_1_4: RXFIFO reaches 1/4 of its depth
2: Depth_1_2: RXFIFO reaches 1/2 of its depth
3: Depth_3_4: RXFIFO reaches 3/4 of its depth
4: Depth_7_8: RXFIFO reaches 7/8 of its depth
5: Full: RXFIFO becomes full

RXFTIE

Bit 28: RXFIFO threshold interrupt enable.

Allowed values:
0: Disabled: Interrupt inhibited
1: Enabled: USART interrupt generated when Receive FIFO reaches the threshold programmed in RXFTCFG

TXFTCFG

Bits 29-31: TXFIFO threshold configuration.

Allowed values:
0: Depth_1_8: TXFIFO reaches 1/8 of its depth
1: Depth_1_4: TXFIFO reaches 1/4 of its depth
2: Depth_1_2: TXFIFO reaches 1/2 of its depth
3: Depth_3_4: TXFIFO reaches 3/4 of its depth
4: Depth_7_8: TXFIFO reaches 7/8 of its depth
5: Empty: TXFIFO becomes empty

BRR

Baud rate register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BRR rw

Toggle fields

BRR

Bits 0-15: Baud rate.

Allowed values: 0x0-0xffff

GTPR

Guard time and prescaler register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
GT rw								PSC rw

Toggle fields

PSC

Bits 0-7: Prescaler value.

Allowed values: 0x0-0xff

GT

Bits 8-15: Guard time value.

Allowed values: 0x0-0xff

RTOR

Receiver timeout register

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BLEN rw								RTO rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RTO rw

Toggle fields

RTO

Bits 0-23: Receiver timeout value.

Allowed values: 0x0-0xffffff

BLEN

Bits 24-31: Block Length.

Allowed values: 0x0-0xff

RQR

Request register

Offset: 0x18, size: 32, reset: 0x00000000, access: write-only

5/5 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
											TXFRQ w	RXFRQ w	MMRQ w	SBKRQ w	ABRRQ w

Toggle fields

ABRRQ

Bit 0: Auto baud rate request.

Allowed values:
1: Request: resets the ABRF flag in the USART_ISR and request an automatic baud rate measurement on the next received data frame

SBKRQ

Bit 1: Send break request.

Allowed values:
1: Break: sets the SBKF flag and request to send a BREAK on the line, as soon as the transmit machine is available

MMRQ

Bit 2: Mute mode request.

Allowed values:
1: Mute: Puts the USART in mute mode and sets the RWU flag

RXFRQ

Bit 3: Receive data flush request.

Allowed values:
1: Discard: clears the RXNE flag. This allows to discard the received data without reading it, and avoid an overrun condition

TXFRQ

Bit 4: Transmit data flush request.

Allowed values:
1: Discard: Set the TXE flags. This allows to discard the transmit data

ISR

Interrupt & status register

Offset: 0x1c, size: 32, reset: 0x000000C0, access: read-only

28/28 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				TXFT r	RXFT r	TCBGT r	RXFF r	TXFE r	REACK r	TEACK r	WUF r	RWU r	SBKF r	CMF r	BUSY r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ABRF r	ABRE r	UDR r	EOBF r	RTOF r	CTS r	CTSIF r	LBDF r	TXE r	TC r	RXNE r	IDLE r	ORE r	NF r	FE r	PE r

Toggle fields

PE

Bit 0: PE.

FE

Bit 1: FE.

NF

Bit 2: NF.

ORE

Bit 3: ORE.

IDLE

Bit 4: IDLE.

RXNE

Bit 5: RXNE.

TC

Bit 6: TC.

TXE

Bit 7: TXE.

LBDF

Bit 8: LBDF.

CTSIF

Bit 9: CTSIF.

CTS

Bit 10: CTS.

RTOF

Bit 11: RTOF.

EOBF

Bit 12: EOBF.

UDR

Bit 13: SPI slave underrun error flag.

ABRE

Bit 14: ABRE.

ABRF

Bit 15: ABRF.

BUSY

Bit 16: BUSY.

CMF

Bit 17: CMF.

SBKF

Bit 18: SBKF.

RWU

Bit 19: RWU.

WUF

Bit 20: WUF.

TEACK

Bit 21: TEACK.

REACK

Bit 22: REACK.

TXFE

Bit 23: TXFIFO Empty.

RXFF

Bit 24: RXFIFO Full.

TCBGT

Bit 25: Transmission complete before guard time flag.

Allowed values:
0: NotCompleted: Transmission not completed
1: Completed: Transmission has completed

RXFT

Bit 26: RXFIFO threshold flag.

TXFT

Bit 27: TXFIFO threshold flag.

ICR

Interrupt flag clear register

Offset: 0x20, size: 32, reset: 0x00000000, access: write-only

15/15 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
											WUCF w			CMCF w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		UDRCF w	EOBCF w	RTOCF w		CTSCF w	LBDCF w	TCBGTCF w	TCCF w	TXFECF w	IDLECF w	ORECF w	NCF w	FECF w	PECF w

Toggle fields

PECF

Bit 0: Parity error clear flag.

Allowed values:
1: Clear: Clears the PE flag in the ISR register

FECF

Bit 1: Framing error clear flag.

Allowed values:
1: Clear: Clears the FE flag in the ISR register

NCF

Bit 2: Noise detected clear flag.

Allowed values:
1: Clear: Clears the NF flag in the ISR register

ORECF

Bit 3: Overrun error clear flag.

Allowed values:
1: Clear: Clears the ORE flag in the ISR register

IDLECF

Bit 4: Idle line detected clear flag.

Allowed values:
1: Clear: Clears the IDLE flag in the ISR register

TXFECF

Bit 5: TXFIFO empty clear flag.

Allowed values:
1: Clear: Clear the TXFE flag in the ISR register

TCCF

Bit 6: Transmission complete clear flag.

Allowed values:
1: Clear: Clears the TC flag in the ISR register

TCBGTCF

Bit 7: Transmission complete before Guard time clear flag.

Allowed values:
1: Clear: Clear the TCBGT flag in the ISR register

LBDCF

Bit 8: LIN break detection clear flag.

Allowed values:
1: Clear: Clears the LBDF flag in the ISR register

CTSCF

Bit 9: CTS clear flag.

Allowed values:
1: Clear: Clears the CTSIF flag in the ISR register

RTOCF

Bit 11: Receiver timeout clear flag.

Allowed values:
1: Clear: Clears the RTOF flag in the ISR register

EOBCF

Bit 12: End of block clear flag.

Allowed values:
1: Clear: Clears the EOBF flag in the ISR register

UDRCF

Bit 13: SPI slave underrun clear flag.

Allowed values:
1: Clear: Clear the UDR flag in the ISR register

CMCF

Bit 17: Character match clear flag.

Allowed values:
1: Clear: Clears the CMF flag in the ISR register

WUCF

Bit 20: Wakeup from Stop mode clear flag.

Allowed values:
1: Clear: Clears the WUF flag in the ISR register

RDR

Receive data register

Offset: 0x24, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							RDR r

Toggle fields

RDR

Bits 0-8: Receive data value.

Allowed values: 0x0-0x1ff

TDR

Transmit data register

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							TDR rw

Toggle fields

TDR

Bits 0-8: Transmit data value.

Allowed values: 0x0-0x1ff

PRESC

Prescaler register

Offset: 0x2c, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
												PRESCALER rw

Toggle fields

PRESCALER

Bits 0-3: Clock prescaler.

Allowed values:
0: Div1: Input clock divided by 1
1: Div2: Input clock divided by 2
2: Div4: Input clock divided by 4
3: Div6: Input clock divided by 6
4: Div8: Input clock divided by 8
5: Div10: Input clock divided by 10
6: Div12: Input clock divided by 12
7: Div16: Input clock divided by 16
8: Div32: Input clock divided by 32
9: Div64: Input clock divided by 64
10: Div128: Input clock divided by 128
11: Div256: Input clock divided by 256

USART2

0x40004400: Universal synchronous asynchronous receiver transmitter

124/124 fields covered.

Toggle register map

Offset	Name	31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	CR1	RXFFIE	TXFEIE	FIFOEN	M1	EOBIE	RTOIE	DEAT					DEDT					OVER8	CMIE	MME	M0	WAKE	PCE	PS	PEIE	TXEIE	TCIE	RXNEIE	IDLEIE	TE	RE	UESM	UE
0x4	CR2	ADD								RTOEN	ABRMOD		ABREN	MSBFIRST	DATAINV	TXINV	RXINV	SWAP	LINEN	STOP		CLKEN	CPOL	CPHA	LBCL		LBDIE	LBDL	ADDM7	DIS_NSS			SLVEN
0x8	CR3	TXFTCFG			RXFTIE	RXFTCFG			TCBGTIE	TXFTIE	WUFIE	WUS		SCARCNT				DEP	DEM	DDRE	OVRDIS	ONEBIT	CTSIE	CTSE	RTSE	DMAT	DMAR	SCEN	NACK	HDSEL	IRLP	IREN	EIE
0xc	BRR																	BRR
0x10	GTPR																	GT								PSC
0x14	RTOR	BLEN								RTO								RTO
0x18	RQR																												TXFRQ	RXFRQ	MMRQ	SBKRQ	ABRRQ
0x1c	ISR					TXFT	RXFT	TCBGT	RXFF	TXFE	REACK	TEACK	WUF	RWU	SBKF	CMF	BUSY	ABRF	ABRE	UDR	EOBF	RTOF	CTS	CTSIF	LBDF	TXE	TC	RXNE	IDLE	ORE	NF	FE	PE
0x20	ICR												WUCF			CMCF				UDRCF	EOBCF	RTOCF		CTSCF	LBDCF	TCBGTCF	TCCF	TXFECF	IDLECF	ORECF	NCF	FECF	PECF
0x24	RDR																								RDR
0x28	TDR																								TDR
0x2c	PRESC																													PRESCALER

Toggle registers

CR1

Control register 1

Offset: 0x0, size: 32, reset: 0x00000000, access: read-write

24/24 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
RXFFIE rw	TXFEIE rw	FIFOEN rw	M1 rw	EOBIE rw	RTOIE rw	DEAT rw					DEDT rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OVER8 rw	CMIE rw	MME rw	M0 rw	WAKE rw	PCE rw	PS rw	PEIE rw	TXEIE rw	TCIE rw	RXNEIE rw	IDLEIE rw	TE rw	RE rw	UESM rw	UE rw

Toggle fields

UE

Bit 0: USART enable.

Allowed values:
0: Disabled: UART is disabled
1: Enabled: UART is enabled

UESM

Bit 1: USART enable in Stop mode.

Allowed values:
0: Disabled: USART not able to wake up the MCU from Stop mode
1: Enabled: USART able to wake up the MCU from Stop mode

RE

Bit 2: Receiver enable.

Allowed values:
0: Disabled: Receiver is disabled
1: Enabled: Receiver is enabled

TE

Bit 3: Transmitter enable.

Allowed values:
0: Disabled: Transmitter is disabled
1: Enabled: Transmitter is enabled

IDLEIE

Bit 4: IDLE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever IDLE=1 in the ISR register

RXNEIE

Bit 5: RXNE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever ORE=1 or RXNE=1 in the ISR register

TCIE

Bit 6: Transmission complete interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever TC=1 in the ISR register

TXEIE

Bit 7: interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever TXE=1 in the ISR register

PEIE

Bit 8: PE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever PE=1 in the ISR register

PS

Bit 9: Parity selection.

Allowed values:
0: Even: Even parity
1: Odd: Odd parity

PCE

Bit 10: Parity control enable.

Allowed values:
0: Disabled: Parity control disabled
1: Enabled: Parity control enabled

WAKE

Bit 11: Receiver wakeup method.

Allowed values:
0: Idle: Idle line
1: Address: Address mask

M0

Bit 12: Word length.

Allowed values:
0: Bit8: 1 start bit, 8 data bits, n stop bits
1: Bit9: 1 start bit, 9 data bits, n stop bits

MME

Bit 13: Mute mode enable.

Allowed values:
0: Disabled: Receiver in active mode permanently
1: Enabled: Receiver can switch between mute mode and active mode

CMIE

Bit 14: Character match interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated when the CMF bit is set in the ISR register

OVER8

Bit 15: Oversampling mode.

Allowed values:
0: Oversampling16: Oversampling by 16
1: Oversampling8: Oversampling by 8

DEDT

Bits 16-20: DEDT.

Allowed values: 0x0-0x1f

DEAT

Bits 21-25: DEAT.

Allowed values: 0x0-0x1f

RTOIE

Bit 26: Receiver timeout interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An USART interrupt is generated when the RTOF bit is set in the ISR register

EOBIE

Bit 27: End of Block interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: A USART interrupt is generated when the EOBF flag is set in the ISR register

M1

Bit 28: Word length.

Allowed values:
0: M0: Use M0 to set the data bits
1: Bit7: 1 start bit, 7 data bits, n stop bits

FIFOEN

Bit 29: FIFO mode enable.

Allowed values:
0: Disabled: FIFO mode is disabled
1: Enabled: FIFO mode is enabled

TXFEIE

Bit 30: TXFIFO empty interrupt enable.

Allowed values:
0: Disabled: Interrupt inhibited
1: Enabled: USART interrupt generated when TXFE = 1 in the USART_ISR register

RXFFIE

Bit 31: RXFIFO Full interrupt enable.

Allowed values:
0: Disabled: Interrupt inhibited
1: Enabled: USART interrupt generated when RXFF = 1 in the USART_ISR register

CR2

Control register 2

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

20/20 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ADD rw								RTOEN rw	ABRMOD rw		ABREN rw	MSBFIRST rw	DATAINV rw	TXINV rw	RXINV rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SWAP rw	LINEN rw	STOP rw		CLKEN rw	CPOL rw	CPHA rw	LBCL rw		LBDIE rw	LBDL rw	ADDM7 rw	DIS_NSS rw			SLVEN rw

Toggle fields

SLVEN

Bit 0: Synchronous Slave mode enable.

Allowed values:
0: Disabled: Slave mode disabled
1: Enabled: Slave mode enabled

DIS_NSS

Bit 3: When the DSI_NSS bit is set, the NSS pin input will be ignored.

Allowed values:
0: Disabled: SPI slave selection depends on NSS input pin
1: Enabled: SPI slave is always selected and NSS input pin is ignored

ADDM7

Bit 4: 7-bit Address Detection/4-bit Address Detection.

Allowed values:
0: Bit4: 4-bit address detection
1: Bit7: 7-bit address detection

LBDL

Bit 5: LIN break detection length.

Allowed values:
0: Bit10: 10-bit break detection
1: Bit11: 11-bit break detection

LBDIE

Bit 6: LIN break detection interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated whenever LBDF=1 in the ISR register

LBCL

Bit 8: Last bit clock pulse.

Allowed values:
0: NotOutput: The clock pulse of the last data bit is not output to the CK pin
1: Output: The clock pulse of the last data bit is output to the CK pin

CPHA

Bit 9: Clock phase.

Allowed values:
0: First: The first clock transition is the first data capture edge
1: Second: The second clock transition is the first data capture edge

CPOL

Bit 10: Clock polarity.

Allowed values:
0: Low: Steady low value on CK pin outside transmission window
1: High: Steady high value on CK pin outside transmission window

CLKEN

Bit 11: Clock enable.

Allowed values:
0: Disabled: CK pin disabled
1: Enabled: CK pin enabled

STOP

Bits 12-13: STOP bits.

Allowed values:
0: Stop1: 1 stop bit
1: Stop0p5: 0.5 stop bit
2: Stop2: 2 stop bit
3: Stop1p5: 1.5 stop bit

LINEN

Bit 14: LIN mode enable.

Allowed values:
0: Disabled: LIN mode disabled
1: Enabled: LIN mode enabled

SWAP

Bit 15: Swap TX/RX pins.

Allowed values:
0: Standard: TX/RX pins are used as defined in standard pinout
1: Swapped: The TX and RX pins functions are swapped

RXINV

Bit 16: RX pin active level inversion.

Allowed values:
0: Standard: RX pin signal works using the standard logic levels
1: Inverted: RX pin signal values are inverted

TXINV

Bit 17: TX pin active level inversion.

Allowed values:
0: Standard: TX pin signal works using the standard logic levels
1: Inverted: TX pin signal values are inverted

DATAINV

Bit 18: Binary data inversion.

Allowed values:
0: Positive: Logical data from the data register are send/received in positive/direct logic
1: Negative: Logical data from the data register are send/received in negative/inverse logic

MSBFIRST

Bit 19: Most significant bit first.

Allowed values:
0: LSB: data is transmitted/received with data bit 0 first, following the start bit
1: MSB: data is transmitted/received with MSB (bit 7/8/9) first, following the start bit

ABREN

Bit 20: Auto baud rate enable.

Allowed values:
0: Disabled: Auto baud rate detection is disabled
1: Enabled: Auto baud rate detection is enabled

ABRMOD

Bits 21-22: Auto baud rate mode.

Allowed values:
0: Start: Measurement of the start bit is used to detect the baud rate
1: Edge: Falling edge to falling edge measurement
2: Frame7F: 0x7F frame detection
3: Frame55: 0x55 frame detection

RTOEN

Bit 23: Receiver timeout enable.

Allowed values:
0: Disabled: Receiver timeout feature disabled
1: Enabled: Receiver timeout feature enabled

ADD

Bits 24-31: Address of the USART node.

Allowed values: 0x0-0xff

CR3

Control register 3

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

24/24 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
TXFTCFG rw			RXFTIE rw	RXFTCFG rw			TCBGTIE rw	TXFTIE rw	WUFIE rw	WUS rw		SCARCNT rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DEP rw	DEM rw	DDRE rw	OVRDIS rw	ONEBIT rw	CTSIE rw	CTSE rw	RTSE rw	DMAT rw	DMAR rw	SCEN rw	NACK rw	HDSEL rw	IRLP rw	IREN rw	EIE rw

Toggle fields

EIE

Bit 0: Error interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated when FE=1 or ORE=1 or NF=1 in the ISR register

IREN

Bit 1: Ir mode enable.

Allowed values:
0: Disabled: IrDA disabled
1: Enabled: IrDA enabled

IRLP

Bit 2: Ir low-power.

Allowed values:
0: Normal: Normal mode
1: LowPower: Low-power mode

HDSEL

Bit 3: Half-duplex selection.

Allowed values:
0: NotSelected: Half duplex mode is not selected
1: Selected: Half duplex mode is selected

NACK

Bit 4: Smartcard NACK enable.

Allowed values:
0: Disabled: NACK transmission in case of parity error is disabled
1: Enabled: NACK transmission during parity error is enabled

SCEN

Bit 5: Smartcard mode enable.

Allowed values:
0: Disabled: Smartcard Mode disabled
1: Enabled: Smartcard Mode enabled

DMAR

Bit 6: DMA enable receiver.

Allowed values:
0: Disabled: DMA mode is disabled for reception
1: Enabled: DMA mode is enabled for reception

DMAT

Bit 7: DMA enable transmitter.

Allowed values:
0: Disabled: DMA mode is disabled for transmission
1: Enabled: DMA mode is enabled for transmission

RTSE

Bit 8: RTS enable.

Allowed values:
0: Disabled: RTS hardware flow control disabled
1: Enabled: RTS output enabled, data is only requested when there is space in the receive buffer

CTSE

Bit 9: CTS enable.

Allowed values:
0: Disabled: CTS hardware flow control disabled
1: Enabled: CTS mode enabled, data is only transmitted when the CTS input is asserted

CTSIE

Bit 10: CTS interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated whenever CTSIF=1 in the ISR register

ONEBIT

Bit 11: One sample bit method enable.

Allowed values:
0: Sample3: Three sample bit method
1: Sample1: One sample bit method

OVRDIS

Bit 12: Overrun Disable.

Allowed values:
0: Enabled: Overrun Error Flag, ORE, is set when received data is not read before receiving new data
1: Disabled: Overrun functionality is disabled. If new data is received while the RXNE flag is still set the ORE flag is not set and the new received data overwrites the previous content of the RDR register

DDRE

Bit 13: DMA Disable on Reception Error.

Allowed values:
0: NotDisabled: DMA is not disabled in case of reception error
1: Disabled: DMA is disabled following a reception error

DEM

Bit 14: Driver enable mode.

Allowed values:
0: Disabled: DE function is disabled
1: Enabled: The DE signal is output on the RTS pin

DEP

Bit 15: Driver enable polarity selection.

Allowed values:
0: High: DE signal is active high
1: Low: DE signal is active low

SCARCNT

Bits 17-19: Smartcard auto-retry count.

Allowed values: 0x0-0x7

WUS

Bits 20-21: Wakeup from Stop mode interrupt flag selection.

Allowed values:
0: Address: WUF active on address match
2: Start: WuF active on Start bit detection
3: RXNE: WUF active on RXNE

WUFIE

Bit 22: Wakeup from Stop mode interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An USART interrupt is generated whenever WUF=1 in the ISR register

TXFTIE

Bit 23: threshold interrupt enable.

Allowed values:
0: Disabled: Interrupt inhibited
1: Enabled: USART interrupt generated when Transmit FIFO reaches the threshold programmed in TXFTCFG

TCBGTIE

Bit 24: Tr Complete before guard time, interrupt enable.

Allowed values:
0: Disabled: Interrupt inhibited
1: Enabled: USART interrupt generated whenever TCBGT=1 in the USART_ISR register

RXFTCFG

Bits 25-27: Receive FIFO threshold configuration.

Allowed values:
0: Depth_1_8: RXFIFO reaches 1/8 of its depth
1: Depth_1_4: RXFIFO reaches 1/4 of its depth
2: Depth_1_2: RXFIFO reaches 1/2 of its depth
3: Depth_3_4: RXFIFO reaches 3/4 of its depth
4: Depth_7_8: RXFIFO reaches 7/8 of its depth
5: Full: RXFIFO becomes full

RXFTIE

Bit 28: RXFIFO threshold interrupt enable.

Allowed values:
0: Disabled: Interrupt inhibited
1: Enabled: USART interrupt generated when Receive FIFO reaches the threshold programmed in RXFTCFG

TXFTCFG

Bits 29-31: TXFIFO threshold configuration.

Allowed values:
0: Depth_1_8: TXFIFO reaches 1/8 of its depth
1: Depth_1_4: TXFIFO reaches 1/4 of its depth
2: Depth_1_2: TXFIFO reaches 1/2 of its depth
3: Depth_3_4: TXFIFO reaches 3/4 of its depth
4: Depth_7_8: TXFIFO reaches 7/8 of its depth
5: Empty: TXFIFO becomes empty

BRR

Baud rate register

Offset: 0xc, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BRR rw

Toggle fields

BRR

Bits 0-15: Baud rate.

Allowed values: 0x0-0xffff

GTPR

Guard time and prescaler register

Offset: 0x10, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
GT rw								PSC rw

Toggle fields

PSC

Bits 0-7: Prescaler value.

Allowed values: 0x0-0xff

GT

Bits 8-15: Guard time value.

Allowed values: 0x0-0xff

RTOR

Receiver timeout register

Offset: 0x14, size: 32, reset: 0x00000000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BLEN rw								RTO rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RTO rw

Toggle fields

RTO

Bits 0-23: Receiver timeout value.

Allowed values: 0x0-0xffffff

BLEN

Bits 24-31: Block Length.

Allowed values: 0x0-0xff

RQR

Request register

Offset: 0x18, size: 32, reset: 0x00000000, access: write-only

5/5 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
											TXFRQ w	RXFRQ w	MMRQ w	SBKRQ w	ABRRQ w

Toggle fields

ABRRQ

Bit 0: Auto baud rate request.

Allowed values:
1: Request: resets the ABRF flag in the USART_ISR and request an automatic baud rate measurement on the next received data frame

SBKRQ

Bit 1: Send break request.

Allowed values:
1: Break: sets the SBKF flag and request to send a BREAK on the line, as soon as the transmit machine is available

MMRQ

Bit 2: Mute mode request.

Allowed values:
1: Mute: Puts the USART in mute mode and sets the RWU flag

RXFRQ

Bit 3: Receive data flush request.

Allowed values:
1: Discard: clears the RXNE flag. This allows to discard the received data without reading it, and avoid an overrun condition

TXFRQ

Bit 4: Transmit data flush request.

Allowed values:
1: Discard: Set the TXE flags. This allows to discard the transmit data

ISR

Interrupt & status register

Offset: 0x1c, size: 32, reset: 0x000000C0, access: read-only

28/28 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				TXFT r	RXFT r	TCBGT r	RXFF r	TXFE r	REACK r	TEACK r	WUF r	RWU r	SBKF r	CMF r	BUSY r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ABRF r	ABRE r	UDR r	EOBF r	RTOF r	CTS r	CTSIF r	LBDF r	TXE r	TC r	RXNE r	IDLE r	ORE r	NF r	FE r	PE r

Toggle fields

PE

Bit 0: PE.

FE

Bit 1: FE.

NF

Bit 2: NF.

ORE

Bit 3: ORE.

IDLE

Bit 4: IDLE.

RXNE

Bit 5: RXNE.

TC

Bit 6: TC.

TXE

Bit 7: TXE.

LBDF

Bit 8: LBDF.

CTSIF

Bit 9: CTSIF.

CTS

Bit 10: CTS.

RTOF

Bit 11: RTOF.

EOBF

Bit 12: EOBF.

UDR

Bit 13: SPI slave underrun error flag.

ABRE

Bit 14: ABRE.

ABRF

Bit 15: ABRF.

BUSY

Bit 16: BUSY.

CMF

Bit 17: CMF.

SBKF

Bit 18: SBKF.

RWU

Bit 19: RWU.

WUF

Bit 20: WUF.

TEACK

Bit 21: TEACK.

REACK

Bit 22: REACK.

TXFE

Bit 23: TXFIFO Empty.

RXFF

Bit 24: RXFIFO Full.

TCBGT

Bit 25: Transmission complete before guard time flag.

Allowed values:
0: NotCompleted: Transmission not completed
1: Completed: Transmission has completed

RXFT

Bit 26: RXFIFO threshold flag.

TXFT

Bit 27: TXFIFO threshold flag.

ICR

Interrupt flag clear register

Offset: 0x20, size: 32, reset: 0x00000000, access: write-only

15/15 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
											WUCF w			CMCF w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		UDRCF w	EOBCF w	RTOCF w		CTSCF w	LBDCF w	TCBGTCF w	TCCF w	TXFECF w	IDLECF w	ORECF w	NCF w	FECF w	PECF w

Toggle fields

PECF

Bit 0: Parity error clear flag.

Allowed values:
1: Clear: Clears the PE flag in the ISR register

FECF

Bit 1: Framing error clear flag.

Allowed values:
1: Clear: Clears the FE flag in the ISR register

NCF

Bit 2: Noise detected clear flag.

Allowed values:
1: Clear: Clears the NF flag in the ISR register

ORECF

Bit 3: Overrun error clear flag.

Allowed values:
1: Clear: Clears the ORE flag in the ISR register

IDLECF

Bit 4: Idle line detected clear flag.

Allowed values:
1: Clear: Clears the IDLE flag in the ISR register

TXFECF

Bit 5: TXFIFO empty clear flag.

Allowed values:
1: Clear: Clear the TXFE flag in the ISR register

TCCF

Bit 6: Transmission complete clear flag.

Allowed values:
1: Clear: Clears the TC flag in the ISR register

TCBGTCF

Bit 7: Transmission complete before Guard time clear flag.

Allowed values:
1: Clear: Clear the TCBGT flag in the ISR register

LBDCF

Bit 8: LIN break detection clear flag.

Allowed values:
1: Clear: Clears the LBDF flag in the ISR register

CTSCF

Bit 9: CTS clear flag.

Allowed values:
1: Clear: Clears the CTSIF flag in the ISR register

RTOCF

Bit 11: Receiver timeout clear flag.

Allowed values:
1: Clear: Clears the RTOF flag in the ISR register

EOBCF

Bit 12: End of block clear flag.

Allowed values:
1: Clear: Clears the EOBF flag in the ISR register

UDRCF

Bit 13: SPI slave underrun clear flag.

Allowed values:
1: Clear: Clear the UDR flag in the ISR register

CMCF

Bit 17: Character match clear flag.

Allowed values:
1: Clear: Clears the CMF flag in the ISR register

WUCF

Bit 20: Wakeup from Stop mode clear flag.

Allowed values:
1: Clear: Clears the WUF flag in the ISR register

RDR

Receive data register

Offset: 0x24, size: 32, reset: 0x00000000, access: read-only

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							RDR r

Toggle fields

RDR

Bits 0-8: Receive data value.

Allowed values: 0x0-0x1ff

TDR

Transmit data register

Offset: 0x28, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							TDR rw

Toggle fields

TDR

Bits 0-8: Transmit data value.

Allowed values: 0x0-0x1ff

PRESC

Prescaler register

Offset: 0x2c, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
												PRESCALER rw

Toggle fields

PRESCALER

Bits 0-3: Clock prescaler.

Allowed values:
0: Div1: Input clock divided by 1
1: Div2: Input clock divided by 2
2: Div4: Input clock divided by 4
3: Div6: Input clock divided by 6
4: Div8: Input clock divided by 8
5: Div10: Input clock divided by 10
6: Div12: Input clock divided by 12
7: Div16: Input clock divided by 16
8: Div32: Input clock divided by 32
9: Div64: Input clock divided by 64
10: Div128: Input clock divided by 128
11: Div256: Input clock divided by 256

VREFBUF

0x40010030: System configuration controller

1/5 fields covered.

Toggle register map

Offset	Name	31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
0x0	CSR																										VRS			VRR		HIZ	ENVR
0x4	CCR																											TRIM

Toggle registers

CSR

VREFBUF control and status register

Offset: 0x0, size: 32, reset: 0x00000002, access: Unspecified

1/4 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
									VRS rw			VRR r		HIZ rw	ENVR rw

Toggle fields

ENVR

Bit 0: Voltage reference buffer mode enable This bit is used to enable the voltage reference buffer mode..

HIZ

Bit 1: High impedance mode This bit controls the analog switch to connect or not the VREF+ pin. Refer to Table196: VREF buffer modes for the mode descriptions depending on ENVR bit configuration..

VRR

Bit 3: Voltage reference buffer ready.

VRS

Bits 4-6: Voltage reference scale These bits select the value generated by the voltage reference buffer. Other: Reserved.

CCR

VREFBUF calibration control register

Offset: 0x4, size: 32, reset: 0x00000000, access: read-write

0/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
										TRIM rw

Toggle fields

TRIM

Bits 0-5: Trimming code These bits are automatically initialized after reset with the trimming value stored in the Flash memory during the production test. Writing into these bits allows to tune the internal reference buffer voltage..

WWDG

0x40002c00: System window watchdog

6/6 fields covered.

Toggle register map

Offset	Name	13	9	7	6	0
0x0	CR			WDGA	T
0x4	CFR	WDGTB	EWI		W
0x8	SR					EWIF

Toggle registers

CR

Control register

Offset: 0x0, size: 32, reset: 0x0000007F, access: read-write

2/2 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								WDGA rw	T rw

Toggle fields

T

Bits 0-6: 7-bit counter (MSB to LSB).

Allowed values: 0x0-0x7f

WDGA

Bit 7: Activation bit.

Allowed values:
0: Disabled: Watchdog disabled
1: Enabled: Watchdog enabled

CFR

Configuration register

Offset: 0x4, size: 32, reset: 0x0000007F, access: read-write

3/3 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		WDGTB rw				EWI rw			W rw

Toggle fields

W

Bits 0-6: 7-bit window value.

Allowed values: 0x0-0x7f

EWI

Bit 9: Early wakeup interrupt.

Allowed values:
1: Enable: interrupt occurs whenever the counter reaches the value 0x40

WDGTB

Bits 11-13: Timer base.

Allowed values:
0: Div1: Counter clock (PCLK1 div 4096) div 1
1: Div2: Counter clock (PCLK1 div 4096) div 2
2: Div4: Counter clock (PCLK1 div 4096) div 4
3: Div8: Counter clock (PCLK1 div 4096) div 8
4: Div16: Counter clock (PCLK1 div 4096) div 16
5: Div32: Counter clock (PCLK1 div 4096) div 32
6: Div64: Counter clock (PCLK1 div 4096) div 64
7: Div128: Counter clock (PCLK1 div 4096) div 128

SR

Status register

Offset: 0x8, size: 32, reset: 0x00000000, access: read-write

1/1 fields covered.

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
															EWIF rw

Toggle fields

EWIF

Bit 0: Early wakeup interrupt flag.

Allowed values:
0: Finished: The EWI Interrupt Service Routine has been serviced
1: Pending: The EWI Interrupt Service Routine has been triggered