ADRDY

Bit 0: ADC ready This bit is set by hardware after the ADC has been enabled (ADEN = 1) and when the ADC reaches a state where it is ready to accept conversion requests. It is cleared by software writing 1 to it..

EOSMP

Bit 1: End of sampling flag This bit is set by hardware during the conversion, at the end of the sampling phase.It is cleared by software by writing 1 to it..

EOC

Bit 2: End of conversion flag This bit is set by hardware at the end of each conversion of a channel when a new data result is available in the ADC_DR register. It is cleared by software writing 1 to it or by reading the ADC_DR register..

EOS

Bit 3: End of sequence flag This bit is set by hardware at the end of the conversion of a sequence of channels selected by the CHSEL bits. It is cleared by software writing 1 to it..

OVR

Bit 4: ADC overrun This bit is set by hardware when an overrun occurs, meaning that a new conversion has complete while the EOC flag was already set. It is cleared by software writing 1 to it..

AWD1

Bit 7: Analog watchdog 1 flag This bit is set by hardware when the converted voltage crosses the values programmed in ADC_TR1 and ADC_HR1 registers. It is cleared by software by writing 1 to it..

AWD2

Bit 8: Analog watchdog 2 flag This bit is set by hardware when the converted voltage crosses the values programmed in ADC_AWD2TR and ADC_AWD2TR registers. It is cleared by software writing 1 to it..

AWD3

Bit 9: Analog watchdog 3 flag This bit is set by hardware when the converted voltage crosses the values programmed in ADC_AWD3TR and ADC_AWD3TR registers. It is cleared by software by writing 1 to it..

EOCAL

Bit 11: End of calibration flag This bit is set by hardware when calibration is complete. It is cleared by software writing 1 to it..

LDORDY

Bit 12: LDO ready This bit is set by hardware. It indicates that the ADC internal LDO output is ready. It is cleared by software by writing 1 to it..

ADRDYIE

Bit 0: ADC ready interrupt enable This bit is set and cleared by software to enable/disable the ADC Ready interrupt. Note: The software is allowed to write this bit only when ADSTART bit is cleared to 0 by writing ADSTP to 1 (this ensures that no conversion is ongoing)..

EOSMPIE

Bit 1: End of sampling flag interrupt enable This bit is set and cleared by software to enable/disable the end of the sampling phase interrupt. Note: The software is allowed to write this bit only when ADSTART bit is cleared to 0 by writing ADSTP to 1 (this ensures that no conversion is ongoing)..

EOCIE

Bit 2: End of conversion interrupt enable This bit is set and cleared by software to enable/disable the end of conversion interrupt. Note: The software is allowed to write this bit only when ADSTART bit is cleared to 0 by writing ADSTP to 1 (this ensures that no conversion is ongoing)..

EOSIE

Bit 3: End of conversion sequence interrupt enable This bit is set and cleared by software to enable/disable the end of sequence of conversions interrupt. Note: The software is allowed to write this bit only when ADSTART bit is cleared to 0 by writing ADSTP to 1 (this ensures that no conversion is ongoing)..

OVRIE

Bit 4: Overrun interrupt enable This bit is set and cleared by software to enable/disable the overrun interrupt. Note: The software is allowed to write this bit only when ADSTART bit is cleared to 0 by writing ADSTP to 1 (this ensures that no conversion is ongoing)..

AWD1IE

Bit 7: Analog watchdog 1 interrupt enable This bit is set and cleared by software to enable/disable the analog watchdog interrupt. Note: The Software is allowed to write this bit only when ADSTART bit is cleared to 0 by writing ADSTP to 1 (this ensures that no conversion is ongoing)..

AWD2IE

Bit 8: Analog watchdog 2 interrupt enable This bit is set and cleared by software to enable/disable the analog watchdog interrupt. Note: The Software is allowed to write this bit only when ADSTART bit is cleared to 0 by writing ADSTP to 1 (this ensures that no conversion is ongoing)..

AWD3IE

Bit 9: Analog watchdog 3 interrupt enable This bit is set and cleared by software to enable/disable the analog watchdog interrupt. Note: The Software is allowed to write this bit only when ADSTART bit is cleared to 0 by writing ADSTP to 1 (this ensures that no conversion is ongoing)..

EOCALIE

Bit 11: End of calibration interrupt enable This bit is set and cleared by software to enable/disable the end of calibration interrupt. Note: The software is allowed to write this bit only when ADSTART bit is cleared to 0 by writing ADSTP to 1 (this ensures that no conversion is ongoing)..

LDORDYIE

Bit 12: LDO ready interrupt enable This bit is set and cleared by software. It is used to enable/disable the LDORDY interrupt. Note: The software is allowed to write this bit only when ADSTART bit is cleared to 0 by writing ADSTP to 1 (this ensure that no conversion is ongoing)..

ADEN

Bit 0: ADC enable command This bit is set by software to enable the ADC. The ADC is effectively ready to operate once the ADRDY flag has been set. It is cleared by hardware when the ADC is disabled, after the execution of the ADDIS command. Note: The software is allowed to set ADEN only when all bits of ADC_CR registers are 0 (ADCAL = 0, ADSTP = 0, ADSTART = 0, ADDIS = 0 and ADEN = 0).

ADDIS

Bit 1: ADC disable command This bit is set by software to disable the ADC (ADDIS command) and put it into power-down state (OFF state). It is cleared by hardware once the ADC is effectively disabled (ADEN is also cleared by hardware at this time). Note: Setting ADDIS to 1 is only effective when ADEN = 1 and ADSTART = 0 (which ensures that no conversion is ongoing).

ADSTART

Bit 2: ADC start conversion command This bit is set by software to start ADC conversion. Depending on the EXTEN [1:0] configuration bits, a conversion either starts immediately (software trigger configuration) or once a hardware trigger event occurs (hardware trigger configuration). It is cleared by hardware: In single conversion mode (CONT = 0, DISCEN = 0), when software trigger is selected (EXTEN = 00): at the assertion of the end of Conversion Sequence (EOS) flag. In discontinuous conversion mode(CONT=0, DISCEN = 1), when the software trigger is selected (EXTEN = 00): at the assertion of the end of Conversion (EOC) flag. In all other cases: after the execution of the ADSTP command, at the same time as the ADSTP bit is cleared by hardware. Note: The software is allowed to set ADSTART only when ADEN = 1 and ADDIS = 0 (ADC is enabled and there is no pending request to disable the ADC)..

ADSTP

Bit 4: ADC stop conversion command This bit is set by software to stop and discard an ongoing conversion (ADSTP Command). It is cleared by hardware when the conversion is effectively discarded and the ADC is ready to accept a new start conversion command. Note: To clear the A/D converter state, ADSTP must be set to 1 even if ADSTART is cleared to 0 after the software trigger A/D conversion. It is recommended to set ADSTP to 1 whenever the configuration needs to be modified..

ADVREGEN

Bit 28: ADC voltage regulator enable This bit is set by software, to enable the ADC internal voltage regulator. The voltage regulator output is available after tsubADCVREG_SETUP/sub. It is cleared by software to disable the voltage regulator. It can be cleared only if ADEN is et to 0. Note: The software is allowed to program this bit field only when the ADC is disabled (ADCAL = 0, ADSTART = 0, ADSTP = 0, ADDIS = 0 and ADEN = 0)..

ADCAL

Bit 31: ADC calibration This bit is set by software to start the calibration of the ADC. It is cleared by hardware after calibration is complete. Note: The software is allowed to set ADCAL only when the ADC is disabled (ADCAL = 0, ADSTART = 0, ADSTP = 0, ADDIS = 0, AUTOFF = 0, and ADEN = 0). Note: The software is allowed to update the calibration factor by writing ADC_CALFACT only when ADEN is set to 1 and ADSTART is cleared to 0 by writing ADSTP to 1 (ADC enabled and no conversion is ongoing)..

DMAEN

Bit 0: Direct memory access enable This bit is set and cleared by software to enable the generation of DMA requests. This allows the automatic management of the converted data by the DMA controller. For more details, refer to Section : Managing converted data using the DMA on page 632. Note: The software is allowed to write this bit only when ADSTART bit is cleared to 0 by writing ADSTP to 1 (this ensures that no conversion is ongoing)..

DMACFG

Bit 1: Direct memory access configuration This bit is set and cleared by software to select between two DMA modes of operation and is effective only when DMAEN = 1. For more details, refer to Section : Managing converted data using the DMA on page 632 Note: The software is allowed to write this bit only when ADSTART bit is cleared to 0 by writing ADSTP to 1 (this ensures that no conversion is ongoing)..

RES

Bits 2-3: Data resolution These bits are written by software to select the resolution of the conversion. Note: The software is allowed to write these bits only when ADSTART bit is cleared to 0 by writing ADSTP to 1 (this ensures that no conversion is ongoing)..

SCANDIR

Bit 4: Scan sequence direction This bit is set and cleared by software to select the direction in which the channels is scanned in the sequence. It is effective only if CHSELRMOD bit is cleared to 0. Note: The software is allowed to write this bit only when ADSTART bit is cleared to 0 by writing ADSTP to 1 (this ensures that no conversion is ongoing)..

ALIGN

Bit 5: Data alignment This bit is set and cleared by software to select right or left alignment. Refer to Figure 78: Data alignment and resolution (oversampling disabled: OVSE = 0) on page 631 Note: The software is allowed to write this bit only when ADSTART bit is cleared to 0 by writing ADSTP to 1 (this ensures that no conversion is ongoing)..

EXTSEL

Bits 6-8: External trigger selection These bits select the external event used to trigger the start of conversion (refer to table ADC interconnection in Section 20.4.2: ADC pins and internal signals for details): Note: The software is allowed to write this bit only when ADSTART bit is cleared to 0 by writing ADSTP to 1 (this ensures that no conversion is ongoing)..

EXTEN

Bits 10-11: External trigger enable and polarity selection These bits are set and cleared by software to select the external trigger polarity and enable the trigger. Note: The software is allowed to write this bit only when ADSTART bit is cleared to 0 by writing ADSTP to 1 (this ensures that no conversion is ongoing)..

OVRMOD

Bit 12: Overrun management mode This bit is set and cleared by software and configure the way data overruns are managed. Note: The software is allowed to write this bit only when ADSTART bit is cleared to 0 by writing ADSTP to 1 (this ensures that no conversion is ongoing)..

CONT

Bit 13: Single / continuous conversion mode This bit is set and cleared by software. If it is set, conversion takes place continuously until it is cleared. Note: It is not possible to have both discontinuous mode and continuous mode enabled: it is forbidden to set both bits DISCEN = 1 and CONT = 1. Note: The software is allowed to write this bit only when ADSTART bit is cleared to 0 by writing ADSTP to 1 (this ensures that no conversion is ongoing)..

WAIT

Bit 14: Wait conversion mode This bit is set and cleared by software to enable/disable wait conversion mode.sup./sup Note: The software is allowed to write this bit only when ADSTART bit is cleared to 0 by writing ADSTP to 1 (this ensures that no conversion is ongoing)..

DISCEN

Bit 16: Discontinuous mode This bit is set and cleared by software to enable/disable discontinuous mode. Note: It is not possible to have both discontinuous mode and continuous mode enabled: it is forbidden to set both bits DISCEN = 1 and CONT = 1. Note: The software is allowed to write this bit only when ADSTART bit is cleared to 0 by writing ADSTP to 1 (this ensures that no conversion is ongoing)..

CHSELRMOD

Bit 21: Mode selection of the ADC_CHSELR register This bit is set and cleared by software to control the ADC_CHSELR feature: Note: The software is allowed to write this bit only when ADSTART bit is cleared to 0 by writing ADSTP to 1 (this ensures that no conversion is ongoing)..

AWD1SGL

Bit 22: Enable the watchdog on a single channel or on all channels This bit is set and cleared by software to enable the analog watchdog on the channel identified by the AWDCH[4:0] bits or on all the channels Note: The software is allowed to write this bit only when ADSTART bit is cleared to 0 by writing ADSTP to 1 (this ensures that no conversion is ongoing)..

AWD1EN

Bit 23: Analog watchdog enable This bit is set and cleared by software. Note: The software is allowed to write this bit only when ADSTART bit is cleared to 0 by writing ADSTP to 1 (this ensures that no conversion is ongoing)..

AWD1CH

Bits 26-30: Analog watchdog channel selection These bits are set and cleared by software. They select the input channel to be guarded by the analog watchdog. ..... Others: Reserved The channel selected by the AWDCH[4:0] bits must be also set into the CHSELR register. Note: The software is allowed to write this bit only when ADSTART bit is cleared to 0 by writing ADSTP to 1 (this ensures that no conversion is ongoing)..

OVSE

Bit 0: Oversampler Enable This bit is set and cleared by software. Note: Software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

OVSR

Bits 2-4: Oversampling ratio This bit filed defines the number of oversampling ratio. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

OVSS

Bits 5-8: Oversampling shift This bit is set and cleared by software. Others: Reserved Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1(which ensures that no conversion is ongoing)..

TOVS

Bit 9: Triggered Oversampling This bit is set and cleared by software. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

LFTRIG

Bit 29: Low frequency trigger mode enable This bit must be set by software. Note: The software is allowed to write this bit only when ADSTART bit is cleared to 0 by writing ADSTP to 1 (this ensures that no conversion is ongoing)..

SMP1

Bits 0-2: Sampling time selection 1 These bits are written by software to select the sampling time that applies to all channels. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

SMP2

Bits 4-6: Sampling time selection 2 These bits are written by software to select the sampling time that applies to all channels. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

SMPSEL0

Bit 8: Channel-x sampling time selection These bits are written by software to define which sampling time is used. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

SMPSEL1

Bit 9: Channel-x sampling time selection These bits are written by software to define which sampling time is used. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

SMPSEL2

Bit 10: Channel-x sampling time selection These bits are written by software to define which sampling time is used. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

SMPSEL3

Bit 11: Channel-x sampling time selection These bits are written by software to define which sampling time is used. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

SMPSEL4

Bit 12: Channel-x sampling time selection These bits are written by software to define which sampling time is used. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

SMPSEL5

Bit 13: Channel-x sampling time selection These bits are written by software to define which sampling time is used. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

SMPSEL6

Bit 14: Channel-x sampling time selection These bits are written by software to define which sampling time is used. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

SMPSEL7

Bit 15: Channel-x sampling time selection These bits are written by software to define which sampling time is used. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

SMPSEL8

Bit 16: Channel-x sampling time selection These bits are written by software to define which sampling time is used. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

SMPSEL9

Bit 17: Channel-x sampling time selection These bits are written by software to define which sampling time is used. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

SMPSEL10

Bit 18: Channel-x sampling time selection These bits are written by software to define which sampling time is used. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

SMPSEL11

Bit 19: Channel-x sampling time selection These bits are written by software to define which sampling time is used. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

SMPSEL12

Bit 20: Channel-x sampling time selection These bits are written by software to define which sampling time is used. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

SMPSEL13

Bit 21: Channel-x sampling time selection These bits are written by software to define which sampling time is used. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

LT1

Bits 0-11: Analog watchdog 1 lower threshold These bits are written by software to define the lower threshold for the analog watchdog. Refer to Section 20.4.25: Analog window watchdog on page 638..

HT1

Bits 16-27: Analog watchdog 1 higher threshold These bits are written by software to define the higher threshold for the analog watchdog. Refer to Section 20.4.25: Analog window watchdog on page 638..

LT2

Bits 0-11: Analog watchdog 2 lower threshold These bits are written by software to define the lower threshold for the analog watchdog. Refer to Section 20.4.25: Analog window watchdog on page 638..

HT2

Bits 16-27: Analog watchdog 2 higher threshold These bits are written by software to define the higher threshold for the analog watchdog. Refer to Section 20.4.25: Analog window watchdog on page 638..

CHSEL0

Bit 0: Channel x selection These bits are written by software and define which channels are part of the sequence of channels to be converted. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

CHSEL1

Bit 1: Channel x selection These bits are written by software and define which channels are part of the sequence of channels to be converted. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

CHSEL2

Bit 2: Channel x selection These bits are written by software and define which channels are part of the sequence of channels to be converted. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

CHSEL3

Bit 3: Channel x selection These bits are written by software and define which channels are part of the sequence of channels to be converted. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

CHSEL4

Bit 4: Channel x selection These bits are written by software and define which channels are part of the sequence of channels to be converted. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

CHSEL5

Bit 5: Channel x selection These bits are written by software and define which channels are part of the sequence of channels to be converted. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

CHSEL6

Bit 6: Channel x selection These bits are written by software and define which channels are part of the sequence of channels to be converted. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

CHSEL7

Bit 7: Channel x selection These bits are written by software and define which channels are part of the sequence of channels to be converted. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

CHSEL8

Bit 8: Channel x selection These bits are written by software and define which channels are part of the sequence of channels to be converted. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

CHSEL9

Bit 9: Channel x selection These bits are written by software and define which channels are part of the sequence of channels to be converted. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

CHSEL10

Bit 10: Channel x selection These bits are written by software and define which channels are part of the sequence of channels to be converted. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

CHSEL11

Bit 11: Channel x selection These bits are written by software and define which channels are part of the sequence of channels to be converted. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

CHSEL12

Bit 12: Channel x selection These bits are written by software and define which channels are part of the sequence of channels to be converted. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

CHSEL13

Bit 13: Channel x selection These bits are written by software and define which channels are part of the sequence of channels to be converted. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

SQ1

Bits 0-3: 1st conversion of the sequence These bits are programmed by software with the channel number assigned to the 1st conversion of the sequence. 0b1111 indicates end of the sequence. When 0b1111 (end of sequence) is programmed to the lower sequence channels, these bits are ignored. Refer to SQ8[3:0] for a definition of channel selection. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

SQ2

Bits 4-7: 2nd conversion of the sequence These bits are programmed by software with the channel number assigned to the 2nd conversion of the sequence. 0b1111 indicates end of the sequence. When 0b1111 (end of sequence) is programmed to the lower sequence channels, these bits are ignored. Refer to SQ8[3:0] for a definition of channel selection. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

SQ3

Bits 8-11: 3rd conversion of the sequence These bits are programmed by software with the channel number assigned to the 3rd conversion of the sequence. 0b1111 indicates end of the sequence. When 0b1111 (end of sequence) is programmed to the lower sequence channels, these bits are ignored. Refer to SQ8[3:0] for a definition of channel selection. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

SQ4

Bits 12-15: 4th conversion of the sequence These bits are programmed by software with the channel number assigned to the 4th conversion of the sequence. 0b1111 indicates end of the sequence. When 0b1111 (end of sequence) is programmed to the lower sequence channels, these bits are ignored. Refer to SQ8[3:0] for a definition of channel selection. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1(which ensures that no conversion is ongoing)..

SQ5

Bits 16-19: 5th conversion of the sequence These bits are programmed by software with the channel number assigned to the 5th conversion of the sequence. 0b1111 indicates end of the sequence. When 0b1111 (end of sequence) is programmed to the lower sequence channels, these bits are ignored. Refer to SQ8[3:0] for a definition of channel selection. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

SQ6

Bits 20-23: 6th conversion of the sequence These bits are programmed by software with the channel number assigned to the 6th conversion of the sequence. 0b1111 indicates end of the sequence. When 0b1111 (end of sequence) is programmed to the lower sequence channels, these bits are ignored. Refer to SQ8[3:0] for a definition of channel selection. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

SQ7

Bits 24-27: 7th conversion of the sequence These bits are programmed by software with the channel number assigned to the 7th conversion of the sequence. 0b1111 indicates end of the sequence. When 0b1111 (end of sequence) is programmed to the lower sequence channels, these bits are ignored. Refer to SQ8[3:0] for a definition of channel selection. Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

SQ8

Bits 28-31: 8th conversion of the sequence These bits are programmed by software with the channel number assigned to the 8th conversion of the sequence. 0b1111 indicates the end of the sequence. When 0b1111 (end of sequence) is programmed to the lower sequence channels, these bits are ignored. ... Note: The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

LT3

Bits 0-11: Analog watchdog 3lower threshold These bits are written by software to define the lower threshold for the analog watchdog. Refer to Section 20.4.25: Analog window watchdog on page 638..

HT3

Bits 16-27: Analog watchdog 3 higher threshold These bits are written by software to define the higher threshold for the analog watchdog. Refer to Section 20.4.25: Analog window watchdog on page 638..

DATA

Bits 0-15: Converted data These bits are read-only. They contain the conversion result from the last converted channel. The data are left- or right-aligned as shown in Figure 78: Data alignment and resolution (oversampling disabled: OVSE = 0) on page 631. Just after a calibration is complete, DATA[6:0] contains the calibration factor..

AUTOFF

Bit 0: Auto-off mode bit This bit is set and cleared by software. it is used to enable/disable the Auto-off mode. Note: The software is allowed to write this bit only when ADEN bit is cleared to 0 (this ensures that no conversion is ongoing)..

DPD

Bit 1: Deep-power-down mode bit This bit is set and cleared by software. It is used to enable/disable Deep-power-down mode in Autonomous mode when the ADC is not used. Note: The software is allowed to write this bit only when ADEN bit is cleared to 0 (this ensures that no conversion is ongoing). Note: Setting DPD in Auto-off mode automatically disables the LDO..

AWD2CH0

Bit 0: Analog watchdog channel selection These bits are set and cleared by software. They enable and select the input channels to be guarded by analog watchdog 2 (AWD2). Note: The channels selected through ADC_AWD2CR must be also configured into the ADC_CHSELR registers. Refer to SQ8[3:0] for a definition of channel selection. The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

AWD2CH1

Bit 1: Analog watchdog channel selection These bits are set and cleared by software. They enable and select the input channels to be guarded by analog watchdog 2 (AWD2). Note: The channels selected through ADC_AWD2CR must be also configured into the ADC_CHSELR registers. Refer to SQ8[3:0] for a definition of channel selection. The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

AWD2CH2

Bit 2: Analog watchdog channel selection These bits are set and cleared by software. They enable and select the input channels to be guarded by analog watchdog 2 (AWD2). Note: The channels selected through ADC_AWD2CR must be also configured into the ADC_CHSELR registers. Refer to SQ8[3:0] for a definition of channel selection. The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

AWD2CH3

Bit 3: Analog watchdog channel selection These bits are set and cleared by software. They enable and select the input channels to be guarded by analog watchdog 2 (AWD2). Note: The channels selected through ADC_AWD2CR must be also configured into the ADC_CHSELR registers. Refer to SQ8[3:0] for a definition of channel selection. The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

AWD2CH4

Bit 4: Analog watchdog channel selection These bits are set and cleared by software. They enable and select the input channels to be guarded by analog watchdog 2 (AWD2). Note: The channels selected through ADC_AWD2CR must be also configured into the ADC_CHSELR registers. Refer to SQ8[3:0] for a definition of channel selection. The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

AWD2CH5

Bit 5: Analog watchdog channel selection These bits are set and cleared by software. They enable and select the input channels to be guarded by analog watchdog 2 (AWD2). Note: The channels selected through ADC_AWD2CR must be also configured into the ADC_CHSELR registers. Refer to SQ8[3:0] for a definition of channel selection. The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

AWD2CH6

Bit 6: Analog watchdog channel selection These bits are set and cleared by software. They enable and select the input channels to be guarded by analog watchdog 2 (AWD2). Note: The channels selected through ADC_AWD2CR must be also configured into the ADC_CHSELR registers. Refer to SQ8[3:0] for a definition of channel selection. The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

AWD2CH7

Bit 7: Analog watchdog channel selection These bits are set and cleared by software. They enable and select the input channels to be guarded by analog watchdog 2 (AWD2). Note: The channels selected through ADC_AWD2CR must be also configured into the ADC_CHSELR registers. Refer to SQ8[3:0] for a definition of channel selection. The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

AWD2CH8

Bit 8: Analog watchdog channel selection These bits are set and cleared by software. They enable and select the input channels to be guarded by analog watchdog 2 (AWD2). Note: The channels selected through ADC_AWD2CR must be also configured into the ADC_CHSELR registers. Refer to SQ8[3:0] for a definition of channel selection. The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

AWD2CH9

Bit 9: Analog watchdog channel selection These bits are set and cleared by software. They enable and select the input channels to be guarded by analog watchdog 2 (AWD2). Note: The channels selected through ADC_AWD2CR must be also configured into the ADC_CHSELR registers. Refer to SQ8[3:0] for a definition of channel selection. The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

AWD2CH10

Bit 10: Analog watchdog channel selection These bits are set and cleared by software. They enable and select the input channels to be guarded by analog watchdog 2 (AWD2). Note: The channels selected through ADC_AWD2CR must be also configured into the ADC_CHSELR registers. Refer to SQ8[3:0] for a definition of channel selection. The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

AWD2CH11

Bit 11: Analog watchdog channel selection These bits are set and cleared by software. They enable and select the input channels to be guarded by analog watchdog 2 (AWD2). Note: The channels selected through ADC_AWD2CR must be also configured into the ADC_CHSELR registers. Refer to SQ8[3:0] for a definition of channel selection. The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

AWD2CH12

Bit 12: Analog watchdog channel selection These bits are set and cleared by software. They enable and select the input channels to be guarded by analog watchdog 2 (AWD2). Note: The channels selected through ADC_AWD2CR must be also configured into the ADC_CHSELR registers. Refer to SQ8[3:0] for a definition of channel selection. The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

AWD2CH13

Bit 13: Analog watchdog channel selection These bits are set and cleared by software. They enable and select the input channels to be guarded by analog watchdog 2 (AWD2). Note: The channels selected through ADC_AWD2CR must be also configured into the ADC_CHSELR registers. Refer to SQ8[3:0] for a definition of channel selection. The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

AWD3CH0

Bit 0: Analog watchdog channel selection These bits are set and cleared by software. They enable and select the input channels to be guarded by analog watchdog 3 (AWD3). Note: The channels selected through ADC_AWD3CR must be also configured into the ADC_CHSELR registers. Refer to SQ8[3:0] for a definition of channel selection. The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

AWD3CH1

Bit 1: Analog watchdog channel selection These bits are set and cleared by software. They enable and select the input channels to be guarded by analog watchdog 3 (AWD3). Note: The channels selected through ADC_AWD3CR must be also configured into the ADC_CHSELR registers. Refer to SQ8[3:0] for a definition of channel selection. The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

AWD3CH2

Bit 2: Analog watchdog channel selection These bits are set and cleared by software. They enable and select the input channels to be guarded by analog watchdog 3 (AWD3). Note: The channels selected through ADC_AWD3CR must be also configured into the ADC_CHSELR registers. Refer to SQ8[3:0] for a definition of channel selection. The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

AWD3CH3

Bit 3: Analog watchdog channel selection These bits are set and cleared by software. They enable and select the input channels to be guarded by analog watchdog 3 (AWD3). Note: The channels selected through ADC_AWD3CR must be also configured into the ADC_CHSELR registers. Refer to SQ8[3:0] for a definition of channel selection. The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

AWD3CH4

Bit 4: Analog watchdog channel selection These bits are set and cleared by software. They enable and select the input channels to be guarded by analog watchdog 3 (AWD3). Note: The channels selected through ADC_AWD3CR must be also configured into the ADC_CHSELR registers. Refer to SQ8[3:0] for a definition of channel selection. The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

AWD3CH5

Bit 5: Analog watchdog channel selection These bits are set and cleared by software. They enable and select the input channels to be guarded by analog watchdog 3 (AWD3). Note: The channels selected through ADC_AWD3CR must be also configured into the ADC_CHSELR registers. Refer to SQ8[3:0] for a definition of channel selection. The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

AWD3CH6

Bit 6: Analog watchdog channel selection These bits are set and cleared by software. They enable and select the input channels to be guarded by analog watchdog 3 (AWD3). Note: The channels selected through ADC_AWD3CR must be also configured into the ADC_CHSELR registers. Refer to SQ8[3:0] for a definition of channel selection. The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

AWD3CH7

Bit 7: Analog watchdog channel selection These bits are set and cleared by software. They enable and select the input channels to be guarded by analog watchdog 3 (AWD3). Note: The channels selected through ADC_AWD3CR must be also configured into the ADC_CHSELR registers. Refer to SQ8[3:0] for a definition of channel selection. The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

AWD3CH8

Bit 8: Analog watchdog channel selection These bits are set and cleared by software. They enable and select the input channels to be guarded by analog watchdog 3 (AWD3). Note: The channels selected through ADC_AWD3CR must be also configured into the ADC_CHSELR registers. Refer to SQ8[3:0] for a definition of channel selection. The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

AWD3CH9

Bit 9: Analog watchdog channel selection These bits are set and cleared by software. They enable and select the input channels to be guarded by analog watchdog 3 (AWD3). Note: The channels selected through ADC_AWD3CR must be also configured into the ADC_CHSELR registers. Refer to SQ8[3:0] for a definition of channel selection. The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

AWD3CH10

Bit 10: Analog watchdog channel selection These bits are set and cleared by software. They enable and select the input channels to be guarded by analog watchdog 3 (AWD3). Note: The channels selected through ADC_AWD3CR must be also configured into the ADC_CHSELR registers. Refer to SQ8[3:0] for a definition of channel selection. The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

AWD3CH11

Bit 11: Analog watchdog channel selection These bits are set and cleared by software. They enable and select the input channels to be guarded by analog watchdog 3 (AWD3). Note: The channels selected through ADC_AWD3CR must be also configured into the ADC_CHSELR registers. Refer to SQ8[3:0] for a definition of channel selection. The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

AWD3CH12

Bit 12: Analog watchdog channel selection These bits are set and cleared by software. They enable and select the input channels to be guarded by analog watchdog 3 (AWD3). Note: The channels selected through ADC_AWD3CR must be also configured into the ADC_CHSELR registers. Refer to SQ8[3:0] for a definition of channel selection. The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

AWD3CH13

Bit 13: Analog watchdog channel selection These bits are set and cleared by software. They enable and select the input channels to be guarded by analog watchdog 3 (AWD3). Note: The channels selected through ADC_AWD3CR must be also configured into the ADC_CHSELR registers. Refer to SQ8[3:0] for a definition of channel selection. The software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

CALFACT

Bits 0-6: Calibration factor These bits are written by hardware or by software. Once a calibration is complete, they are updated by hardware with the calibration factors. Software can write these bits with a new calibration factor. If the new calibration factor is different from the current one stored into the analog ADC, it is then applied once a new calibration is launched. Just after a calibration is complete, DATA[6:0] contains the calibration factor. Note: Software can write these bits only when ADEN = 1 (ADC is enabled and no calibration is ongoing and no conversion is ongoing)..

PRESC

Bits 18-21: ADC prescaler Set and cleared by software to select the frequency of the clock to the ADC. Other: Reserved Note: Software is allowed to write these bits only when the ADC is disabled (ADCAL = 0, ADSTART = 0, ADSTP = 0, ADDIS = 0 and ADEN = 0)..

VREFEN

Bit 22: VsubREFINT/sub enable This bit is set and cleared by software to enable/disable the VsubREFINT/sub buffer. Note: Software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

VSENSESEL

Bit 23: Temperature sensor selection This bit is set and cleared by software to enable/disable the temperature sensor. Note: Software is allowed to write this bit only when ADSTART is cleared to 0 by writing ADSTP to 1 (which ensures that no conversion is ongoing)..

EN

Bit 0: Enable This bit enables/disables the AES peripheral. At any moment, clearing then setting the bit re-initializes the AES peripheral. This bit is automatically cleared by hardware upon the completion of the key preparation (MODE[1:0] at 01) and upon the completion of GCM/GMAC/CCM initialization phase. The bit cannot be set as long as KEYVALID=0..

DATATYPE

Bits 1-2: Data type This bitfield defines the format of data written in the AES_DINR register or read from the AES_DOUTR register, through selecting the mode of data swapping. This swapping is defined in Section23.4.17: AES data registers and data swapping. Attempts to write the bitfield are ignored when BUSY is set, as well as when EN is set before the write access and it is not cleared by that write access..

MODE

Bits 3-4: Operating mode This bitfield selects the AES operating mode: Attempts to write the bitfield are ignored when BUSY is set, as well as when EN is set before the write access and it is not cleared by that write access..

CHMOD

Bits 5-6: CHMOD[1:0]: Chaining mode This bitfield selects the AES chaining mode: others: Reserved Attempts to write the bitfield are ignored when BUSY is set, as well as when EN is set before the write access and it is not cleared by that write access..

DMAINEN

Bit 11: DMA input enable When this bit is set, DMA requests are automatically generated by the peripheral during the input data phase. Setting this bit is ignored when MODE[1:0] is at 01 (key derivation)..

DMAOUTEN

Bit 12: DMA output enable When this bit is set, DMA requests are automatically generated by the peripheral during the output data phase. Setting this bit is ignored when MODE[1:0] is at 01 (key derivation)..

GCMPH

Bits 13-14: GCM or CCM phase selection This bitfield selects the phase, applicable only with GCM, GMAC or CCM chaining modes. This bitfield has no effect if GCM, GMAC or CCM algorithm is not selected with CHMOD[2:0]..

CHMOD_1

Bit 16: CHMOD[2].

KEYSIZE

Bit 18: Key size selection This bitfield defines the key length in bits of the key used by AES. Attempts to write the bit are ignored when BUSY is set, as well as when the EN is set before the write access and it is not cleared by that write access..

NPBLB

Bits 20-23: Number of padding bytes in last block This padding information must be filled by software before processing the last block of GCM payload encryption or CCM payload decryption, otherwise authentication tag computation is incorrect. ....

KMOD

Bits 24-25: Key mode selection The bitfield defines how the AES key can be used by the application. KEYSIZE must be correctly initialized when setting KMOD[1:0] different from zero. Others: Reserved Attempts to write the bitfield are ignored when BUSY is set, as well as when EN is set before the write access and it is not cleared by that write access..

IPRST

Bit 31: AES peripheral software reset Setting the bit resets the AES peripheral, putting all registers to their default values, except the IPRST bit itself. Hence, any key-relative data are lost. For this reason, it is recommended to set the bit before handing over the AES to a less secure application. The bit must be low while writing any configuration registers..

RDERRF

Bit 1: Read error flag This bit is set when an unexpected read to the AES_DOUTR register occurred. When set RDERRF bit has no impact on the AES operations. This flag is cleared by setting the RWEIF bit in AES_ICR register. If RWEIE bit is set in AES_IER register an interrupt is generated when RDERRF is set. It is cleared by setting the RWEIF bit of the AES_ICR register..

WRERRF

Bit 2: Write error flag This bit is set when an unexpected write to the AES_DINR register occurred. When set WRERRF bit has no impact on the AES operations. This flag is cleared by setting the RWEIF bit in AES_ICR register. If RWEIE bit is set in AES_IER register an interrupt is generated when WRERRF is set. It is cleared by setting the RWEIF bit of the AES_ICR register..

BUSY

Bit 3: Busy This flag indicates whether AES is idle or busy. AES is flagged as idle when disabled or when the last processing is completed. AES is flagged as busy when processing a block data, preparing a key (ECB or CBC decryption only), or transferring a shared key from SAES peripheral. When GCM encryption is selected, this flag must be at zero before suspending current process to manage a higher-priority message..

KEYVALID

Bit 7: Key valid flag This bit is set by hardware when the key of size defined by KEYSIZE is loaded in AES_KEYRx key registers. The EN bit can only be set when KEYVALID is set. In normal mode when KEYSEL[2:0] is at 000, the key must be written in the key registers in the correct sequence, otherwise the KEIF flag is set and KEYVALID remains cleared. When KEYSEL[2:0] is different from zero, the BUSY flag is automatically set by AES. When the key is loaded successfully, BUSY is cleared and KEYVALID set. Upon an error, KEIF is set, BUSY cleared and KEYVALID remains cleared. If set, KEIF must be cleared through the AES_ICR register, otherwise KEYVALID cannot be set. See the KEIF flag description for more details. For further information on key loading, refer to Section23.4.18: AES key registers..

DIN

Bits 0-31: Input data word A four-fold sequential write to this bitfield during the Input phase results in writing a complete 16-bytes block of input data to the AES peripheral. From the first to the fourth write, the corresponding data weights are [127:96], [95:64], [63:32], and [31:0]. Upon each write, the data from the 32-bit input buffer are handled by the data swap block according to the DATATYPE[1:0] bitfield, then written into the AES core 16-bytes input buffer. Reads return zero..

DOUT

Bits 0-31: Output data word This read-only bitfield fetches a 32-bit output buffer. A four-fold sequential read of this bitfield, upon the computation completion (CCF flag set), virtually reads a complete 16-byte block of output data from the AES peripheral. Before reaching the output buffer, the data produced by the AES core are handled by the data swap block according to the DATATYPE[1:0] bitfield. Data weights from the first to the fourth read operation are: [127:96], [95:64], [63:32], and [31:0]..

KEY

Bits 0-31: Cryptographic key, bits [31:0] This write-only bitfield contains the bits [31:0] of the AES encryption or decryption key, depending on the operating mode MODE[1:0] in AES_CR. The AES_KEYRx registers may be written only when KEYSIZE value is correct and when the AES peripheral is disabled (EN bit of the AES_CR register cleared). A special writing sequence is also required, as described in KEYVALID bit of the AES_SR register. Note that, if KMOD[1:0] is at 10 (shared key), the key is directly loaded from SAES peripheral to AES_KEYRx registers (hence writes to key register is ignored and KEIF is set). When KEYVALID is set a write to this register clears KEYVALID if AES is disabled..

KEY

Bits 0-31: Cryptographic key, bits [63:32] Refer to the AES_KEYR0 register for description of the KEY[255:0] bitfield. When KEYVALID is set in AES_SR a write to this register clears KEYVALID if EN is cleared in AES_CR..

KEY

Bits 0-31: Cryptographic key, bits [95:64] Refer to the AES_KEYR0 register for description of the KEY[255:0] bitfield. When KEYVALID is set in AES_SR a write to this register clears KEYVALID if EN is cleared in AES_CR..

KEY

Bits 0-31: Cryptographic key, bits [127:96] Refer to the AES_KEYR0 register for description of the KEY[255:0] bitfield. When KEYVALID is set in AES_SR a write to this register clears KEYVALID if EN is cleared in AES_CR..

IVI

Bits 0-31: Initialization vector input, bits [31:0] AES_IVRx registers store the 128-bit initialization vector or the nonce, depending on the chaining mode selected. This value is updated by the AES core after each computation round (when applicable). Write to this register is ignored when EN bit is set in AES_SR register.

IVI

Bits 0-31: Initialization vector input, bits [63:32] Refer to the AES_IVR0 register for description of the IVI[128:0] bitfield..

IVI

Bits 0-31: Initialization vector input, bits [95:64] Refer to the AES_IVR0 register for description of the IVI[128:0] bitfield..

IVI

Bits 0-31: Initialization vector input, bits [127:96] Refer to the AES_IVR0 register for description of the IVI[128:0] bitfield..

KEY

Bits 0-31: Cryptographic key, bits [159:128] Refer to the AES_KEYR0 register for description of the KEY[255:0] bitfield. Writing to this register has no effect when key size is 128-bit (KEYSIZE=0). When KEYVALID is set in AES_SR a write to this register clears KEYVALID if EN is cleared in AES_CR..

KEY

Bits 0-31: Cryptographic key, bits [191:160] Refer to the AES_KEYR0 register for description of the KEY[255:0] bitfield. Writing to this register has no effect when key size is 128-bit (KEYSIZE=0). When KEYVALID is set in AES_SR a write to this register clears KEYVALID if EN is cleared in AES_CR..

KEY

Bits 0-31: Cryptographic key, bits [223:192] Refer to the AES_KEYR0 register for description of the KEY[255:0] bitfield. Writing to this register has no effect when key size is 128-bit (KEYSIZE=0). When KEYVALID is set in AES_SR a write to this register clears KEYVALID if EN is cleared in AES_CR..

KEY

Bits 0-31: Cryptographic key, bits [255:224] Refer to the AES_KEYR0 register for description of the KEY[255:0] bitfield. Writing to this register has no effect when key size is 128-bit (KEYSIZE=0). When KEYVALID is set in AES_SR a write to this register clears KEYVALID if EN is cleared in AES_CR..

SUSP

Bits 0-31: Suspend data AES_SUSPRx registers contain the complete internal register states of the AES when the GCM, GMAC or CCM processing of the current task is suspended to process a higher-priority task. Refer to Section23.4.8: AES suspend and resume operations for more details. Read to this register returns zero when EN bit is cleared in AES_SR register. AES_SUSPRx registers are not used in other chaining modes than GCM, GMAC or CCM..

SUSP

Bits 0-31: Suspend data AES_SUSPRx registers contain the complete internal register states of the AES when the GCM, GMAC or CCM processing of the current task is suspended to process a higher-priority task. Refer to Section23.4.8: AES suspend and resume operations for more details. Read to this register returns zero when EN bit is cleared in AES_SR register. AES_SUSPRx registers are not used in other chaining modes than GCM, GMAC or CCM..

SUSP

Bits 0-31: Suspend data AES_SUSPRx registers contain the complete internal register states of the AES when the GCM, GMAC or CCM processing of the current task is suspended to process a higher-priority task. Refer to Section23.4.8: AES suspend and resume operations for more details. Read to this register returns zero when EN bit is cleared in AES_SR register. AES_SUSPRx registers are not used in other chaining modes than GCM, GMAC or CCM..

SUSP

Bits 0-31: Suspend data AES_SUSPRx registers contain the complete internal register states of the AES when the GCM, GMAC or CCM processing of the current task is suspended to process a higher-priority task. Refer to Section23.4.8: AES suspend and resume operations for more details. Read to this register returns zero when EN bit is cleared in AES_SR register. AES_SUSPRx registers are not used in other chaining modes than GCM, GMAC or CCM..

SUSP

Bits 0-31: Suspend data AES_SUSPRx registers contain the complete internal register states of the AES when the GCM, GMAC or CCM processing of the current task is suspended to process a higher-priority task. Refer to Section23.4.8: AES suspend and resume operations for more details. Read to this register returns zero when EN bit is cleared in AES_SR register. AES_SUSPRx registers are not used in other chaining modes than GCM, GMAC or CCM..

SUSP

Bits 0-31: Suspend data AES_SUSPRx registers contain the complete internal register states of the AES when the GCM, GMAC or CCM processing of the current task is suspended to process a higher-priority task. Refer to Section23.4.8: AES suspend and resume operations for more details. Read to this register returns zero when EN bit is cleared in AES_SR register. AES_SUSPRx registers are not used in other chaining modes than GCM, GMAC or CCM..

SUSP

Bits 0-31: Suspend data AES_SUSPRx registers contain the complete internal register states of the AES when the GCM, GMAC or CCM processing of the current task is suspended to process a higher-priority task. Refer to Section23.4.8: AES suspend and resume operations for more details. Read to this register returns zero when EN bit is cleared in AES_SR register. AES_SUSPRx registers are not used in other chaining modes than GCM, GMAC or CCM..

SUSP

Bits 0-31: Suspend data AES_SUSPRx registers contain the complete internal register states of the AES when the GCM, GMAC or CCM processing of the current task is suspended to process a higher-priority task. Refer to Section23.4.8: AES suspend and resume operations for more details. Read to this register returns zero when EN bit is cleared in AES_SR register. AES_SUSPRx registers are not used in other chaining modes than GCM, GMAC or CCM..

CCFIE

Bit 0: Computation complete flag interrupt enable This bit enables or disables (masks) the AES interrupt generation when CCF (computation complete flag) is set..

RWEIE

Bit 1: Read or write error interrupt enable This bit enables or disables (masks) the AES interrupt generation when RWEIF (read and/or write error flag) is set..

KEIE

Bit 2: Key error interrupt enable This bit enables or disables (masks) the AES interrupt generation when KEIF (key error flag) is set..

CCF

Bit 0: Computation complete flag This flag indicates whether the computation is completed. It is significant only when the DMAOUTEN bit is cleared, and it may stay high when DMAOUTEN is set. CCF bit is cleared when application sets the corresponding bit of AES_ICR register. An interrupt is generated if the CCFIE bit has been previously set in the AES_IER register..

RWEIF

Bit 1: Read or write error interrupt flag This read-only bit is set by hardware when a RDERRF or a WRERRF error flag is set in the AES_SR register. RWEIF bit is cleared when application sets the corresponding bit of AES_ICR register. An interrupt is generated if the RWEIE bit has been previously set in the AES_IER register. This flags has no meaning when key derivation mode is selected..

KEIF

Bit 2: Key error interrupt flag This read-only bit is set by hardware when key information failed to load into key registers. Setting the corresponding bit of the AES_ICR register clears the KEIF and generates interrupt if the KEIE bit of the AES_IER register is set. KEIF is triggered upon any of the following errors: AES_KEYRx register write does not respect the correct order. (For KEYSIZE=0, AES_KEYR0 then AES_KEYR1 then AES_KEYR2 then AES_KEYR3 register, or reverse. For KEYSIZE set, AES_KEYR0 then AES_KEYR1 then AES_KEYR2 then AES_KEYR3 then AES_KEYR4 then AES_KEYR5 then AES_KEYR6 then AES_KEYR7, or reverse). KEIF must be cleared by the application software, otherwise KEYVALID cannot be set..

CCF

Bit 0: Computation complete flag clear Setting this bit clears the CCF status bit of the AES_ISR register..

RWEIF

Bit 1: Read or write error interrupt flag clear Setting this bit clears the RWEIF status bit of the AES_ISR register, and clears both RDERRF and WRERRF flags in the AES_SR register..

KEIF

Bit 2: Key error interrupt flag clear Setting this bit clears the KEIF status bit of the AES_ISR register..

EN

Bit 0: COMP1 enable.

INMSEL

Bits 4-7: COMP1 signal selector for inverting input INM Controlled by software (if not locked), selects the signal for the inverting input COMP1_INM.

INPSEL

Bits 8-10: COMP1 signal selector for inverting input INM Controlled by software (if not locked), selects the signal for the inverting input COMP1_INM.

WINMODE

Bit 11: COMP1 noninverting input selector for window mode Controlled by software (if not locked), selects the signal for the COMP1_INP input of the COMP1..

WINOUT

Bit 14: COMP1 output selector Controlled by software (if not locked), selects the COMP1 output..

POLARITY

Bit 15: COMP1 polarity selector Controlled by software (if not locked), selects the COMP1 output polarity.

HYST

Bits 16-17: COMP1 hysteresis selector Controlled by software (if not locked), selects the COMP1 hysteresis..

PWRMODE

Bits 18-19: COMP1 power mode selector Controlled by software (if not locked), selects the power consumption and, as a consequence, the speed of the COMP1..

BLANKSEL

Bits 20-24: COMP1 blanking source selector..

VALUE

Bit 30: COMP1 output status..

LOCK

Bit 31: COMP1_CSR register lock..

EN

Bit 0: COMP1 enable.

INMSEL

Bits 4-7: COMP1 signal selector for inverting input INM Controlled by software (if not locked), selects the signal for the inverting input COMP1_INM.

INPSEL

Bits 8-9: COMP1 signal selector for inverting input INM Controlled by software (if not locked), selects the signal for the inverting input COMP1_INM.

WINMODE

Bit 11: COMP1 noninverting input selector for window mode Controlled by software (if not locked), selects the signal for the COMP1_INP input of the COMP1..

WINOUT

Bit 14: COMP1 output selector Controlled by software (if not locked), selects the COMP1 output..

POLARITY

Bit 15: COMP1 polarity selector Controlled by software (if not locked), selects the COMP1 output polarity.

HYST

Bits 16-17: COMP1 hysteresis selector Controlled by software (if not locked), selects the COMP1 hysteresis..

PWRMODE

Bits 18-19: COMP1 power mode selector Controlled by software (if not locked), selects the power consumption and, as a consequence, the speed of the COMP1..

BLANKSEL

Bits 20-24: COMP1 blanking source selector..

VALUE

Bit 30: COMP1 output status..

LOCK

Bit 31: COMP1_CSR register lock..

DR

Bits 0-31: Data register bits This register is used to write new data to the CRC calculator. It holds the previous CRC calculation result when it is read. If the data size is less than 32 bits, the least significant bits are used to write/read the correct value..

IDR

Bits 0-31: General-purpose 32-bit data register bits These bits can be used as a temporary storage location for four bytes. This register is not affected by CRC resets generated by the RESET bit in the CRC_CR register.

RESET

Bit 0: RESET bit This bit is set by software to reset the CRC calculation unit and set the data register to the value stored in the CRC_INIT register. This bit can only be set, it is automatically cleared by hardware.

POLYSIZE

Bits 3-4: Polynomial size These bits control the size of the polynomial..

REV_IN

Bits 5-6: Reverse input data These bits control the reversal of the bit order of the input data.

REV_OUT

Bit 7: Reverse output data This bit controls the reversal of the bit order of the output data..

CRC_INIT

Bits 0-31: Programmable initial CRC value This register is used to write the CRC initial value..

POL

Bits 0-31: Programmable polynomial This register is used to write the coefficients of the polynomial to be used for CRC calculation. If the polynomial size is less than 32 bits, the least significant bits have to be used to program the correct value..

DEV_ID

Bits 0-11: Device ID.

REV_ID

Bits 16-31: Revision ID.

DBG_STOP

Bit 1: Allows debug in Stop mode Write access can be protected by PWR_SECCFGR.LPMSEC. The CPU debug and DBGMCU clocks remain active and the HSI16 oscillators is used as system clock during Stop debug mode, allowing CPU debug capability. On exit from Stop mode, the clock settings are set to the Stop mode exit state..

DBG_STANDBY

Bit 2: Allows debug in Standby mode Write access can be protected by PWR_SECCFGR.LPMSEC. The CPU debug and DBGMCU clocks remain active and the HSI16 oscillator is used as system clock, the supply and SRAM memory content is maintained during Standby debug mode, allowing CPU debug capability. On exit from Standby mode, a standby reset is performed..

LPMS

Bits 16-18: Device low power mode selected 10x: Standby mode others reserved.

STOPF

Bit 19: Device Stop flag.

SBF

Bit 20: Device Standby flag.

CS

Bit 24: CPU Sleep.

CDS

Bit 25: CPU DeepSleep.

DBG_TIM2_STOP

Bit 0: TIM2 stop in CPU debug Write access can be protected by GTZC_TZSC.TIM2SEC..

DBG_TIM3_STOP

Bit 1: TIM3 stop in CPU debug Write access can be protected by GTZC_TZSC.TIM3SEC..

DBG_WWDG_STOP

Bit 11: WWDG stop in CPU debug Write access can be protected by GTZC_TZSC.WWDGSEC.

DBG_IWDG_STOP

Bit 12: IWDG stop in CPU debug Write access can be protected by GTZC_TZSC.IWDGSEC..

DBG_I2C1_STOP

Bit 21: I2C1 SMBUS timeout stop in CPU debug Write access can be protected by GTZC_TZSC.I2C1SEC..

DBG_LPTIM2_STOP

Bit 5: LPTIM2 stop in CPU debug Write access can be protected by GTZC_TZSC.LPTIM2SEC..

DBG_TIM1_STOP

Bit 11: TIM1 stop in CPU debug Write access can be protected by GTZC_TZSC.TIM1SEC..

DBG_TIM16_STOP

Bit 17: TIM16 stop in CPU debug Write access can be protected by GTZC_TZSC.TIM16SEC..

DBG_TIM17_STOP

Bit 18: TIM17 stop in CPU debug Write access can be protected by GTZC_TZSC.TIM17SEC..

DBG_I2C3_STOP

Bit 10: I2C3 stop in CPU debug Access can be protected by GTZC_TZSC.I2C3SEC..

DBG_LPTIM1_STOP

Bit 17: LPTIM1 stop in CPU debug Access can be protected by GTZC_TZSC.LPTIM1SEC..

DBG_RTC_STOP

Bit 30: RTC stop in CPU debug Access can be protected by GTZC_TZSC.TIM17SEC. Can only be accessed secure when one or more features in the RTC or TAMP is/are secure..

DBG_GPDMA1_CH0_STOP

Bit 0: GPDMA 1 channel 0 stop in CPU debug Write access can be protected by GPDMA_SECCFGR.SEC0..

DBG_GPDMA1_CH1_STOP

Bit 1: GPDMA 1 channel 1 stop in CPU debug Write access can be protected by GPDMA_SECCFGR.SEC1..

DBG_GPDMA1_CH2_STOP

Bit 2: GPDMA 1 channel 2 stop in CPU debug Write access can be protected by GPDMA_SECCFGR.SEC2..

DBG_GPDMA1_CH3_STOP

Bit 3: GPDMA 1 channel 3 stop in CPU debug Write access can be protected by GPDMA_SECCFGR.SEC3..

DBG_GPDMA1_CH4_STOP

Bit 4: GPDMA 1 channel 4 stop in CPU debug Write access can be protected by GPDMA_SECCFGR.SEC4..

DBG_GPDMA1_CH5_STOP

Bit 5: GPDMA 1 channel 5 stop in CPU debug Write access can be protected by GPDMA_SECCFGR.SEC5..

DBG_GPDMA1_CH6_STOP

Bit 6: GPDMA 1 channel 6 stop in CPU debug Write access can be protected by GPDMA_SECCFGR.SEC6..

DBG_GPDMA1_CH7_STOP

Bit 7: GPDMA 1 channel 7 stop in CPU debug Write access can be protected by GPDMA_SECCFGR.SEC7..

AP_PRESENT

Bits 0-15: Bit n identifies whether access port APn is present in device Bit n = 0: APn absent Bit n = 1: APn present.

AP_ENABLED

Bits 16-31: Bit n identifies whether access port APn is open (can be accessed via the debug port) or locked (debug access to the APn is blocked, except for DBGMCU access) Bit n = 0: APn locked (except for access to DBGMCU) Bit n = 1: APn enabled.

AUTH_KEY

Bits 0-31: Device authentication key The device specific 64-bit authentication key (OEMn key) must be written to this register (in two successive 32-bit writes, least significant word first) to permit RDP regression. Writing a wrong key locks access to the device and prevent code execution from the Flash memory..

AUTH_ID

Bits 0-31: Device specific ID Device specific ID used for RDP regression..

CODIFICATION

Bits 0-31: Part number codification.

JEP106CON

Bits 0-3: JEP106 continuation code.

F4KCOUNT

Bits 4-7: Register file size.

PARTNUM

Bits 0-7: Part number bits [7:0].

PARTNUM

Bits 0-3: Part number bits [11:8].

JEP106ID

Bits 4-7: JEP106 identity code bits [3:0].

JEP106ID

Bits 0-2: JEP106 identity code bits [6:4].

JEDEC

Bit 3: JEDEC assigned value.

REVISION

Bits 4-7: Component revision number.

CMOD

Bits 0-3: Customer modified.

REVAND

Bits 4-7: Metal fix version.

PREAMBLE

Bits 0-7: Component ID bits [7:0].

PREAMBLE

Bits 0-3: Component ID bits [11:8].

CLASS

Bits 4-7: Component ID bits [15:12] - component class.

PREAMBLE

Bits 0-7: Component ID bits [23:16].

PREAMBLE

Bits 0-7: Component ID bits [31:24].

CDS

Bit 16: Current domain Secure.