STM32F750 1.9 STM32F750 CM7 r0p1 little true true 4 false 8 32 0x20 0x00000000 0xFFFFFFFF RNG Random number generator RNG 0x50060800 0x0 0x400 registers HASH_RNG Hash and Rng global interrupt 80 CR CR control register 0x0 0x20 read-write 0x00000000 IE Interrupt enable 3 1 IE Disabled RNG interrupt is disabled 0 Enabled RNG interrupt is enabled 1 RNGEN Random number generator enable 2 1 RNGEN Disabled Random number generator is disabled 0 Enabled Random number generator is enabled 1 SR SR status register 0x4 0x20 0x00000000 CEIS Clock error interrupt status 5 1 read-write zeroToClear CEISW write Clear Clear flag 0 CEISR read Correct The RNG clock is correct 0 Slow The RNG has been detected too slow An interrupt is pending if IE = 1 in the RNG_CR register 1 SEIS Seed error interrupt status 6 1 read-write zeroToClear write SEISR read NoFault No faulty sequence detected 0 Fault At least one faulty sequence has been detected. See **SECS** bit description for details. An interrupt is pending if IE = 1 in the RNG_CR register. 1 SECS Seed error current status 2 1 read-only SECS NoFault No faulty sequence has currently been detected. If the SEIS bit is set, this means that a faulty sequence was detected and the situation has been recovered. 0 Fault At least one faulty sequence has been detected - see ref manual for details 1 CECS Clock error current status 1 1 read-only CECS Correct The RNG clock is correct. If the CEIS bit is set, this means that a slow clock was detected and the situation has been recovered. 0 Slow The RNG clock is too slow 1 DRDY Data ready 0 1 read-only DRDY Invalid The RNG_DR register is not yet valid, no random data is available 0 Valid The RNG_DR register contains valid random data. Once the RNG_DR register has been read, this bit returns to 0 until a new random value is generated. 1 DR DR data register 0x8 0x20 read-only 0x00000000 RNDATA Random data 0 32 0 4294967295 HASH Hash processor HASH 0x50060400 0x0 0x400 registers CR CR control register 0x0 0x20 0x00000000 INIT Initialize message digest calculation 2 1 write-only DMAE DMA enable 3 1 read-write DATATYPE Data type selection 4 2 read-write MODE Mode selection 6 1 read-write ALGO0 Algorithm selection 7 1 read-write NBW Number of words already pushed 8 4 read-only DINNE DIN not empty 12 1 read-only MDMAT Multiple DMA Transfers 13 1 read-write LKEY Long key selection 16 1 read-write ALGO1 ALGO 18 1 read-write DIN DIN data input register 0x4 0x20 read-write 0x00000000 DATAIN Data input 0 32 STR STR start register 0x8 0x20 0x00000000 DCAL Digest calculation 8 1 write-only NBLW Number of valid bits in the last word of the message 0 5 read-write 5 0x4 0-4 HR%s HR%s digest registers 0xC 0x20 read-only 0x00000000 H H0 0 32 IMR IMR interrupt enable register 0x20 0x20 read-write 0x00000000 DCIE Digest calculation completion interrupt enable 1 1 DINIE Data input interrupt enable 0 1 SR SR status register 0x24 0x20 0x00000001 BUSY Busy bit 3 1 read-only DMAS DMA Status 2 1 read-only DCIS Digest calculation completion interrupt status 1 1 read-write DINIS Data input interrupt status 0 1 read-write 54 0x4 0-53 CSR%s CSR%s context swap registers 0xF8 0x20 read-write 0x00000000 CSR CSR0 0 32 8 0x4 0-7 HASH_HR%s HASH_HR%s HASH digest register %s 0x310 0x20 read-only 0x00000000 H H0 0 32 CRYP Cryptographic processor CRYP 0x50060000 0x0 0x400 registers CR CR control register 0x0 0x20 0x00000000 ALGODIR Algorithm direction 2 1 read-write ALGOMODE0 Algorithm mode 3 3 read-write DATATYPE Data type selection 6 2 read-write KEYSIZE Key size selection (AES mode only) 8 2 read-write FFLUSH FIFO flush 14 1 write-only CRYPEN Cryptographic processor enable 15 1 read-write GCM_CCMPH GCM_CCMPH 16 2 read-write ALGOMODE3 ALGOMODE 19 1 read-write SR SR status register 0x4 0x20 read-only 0x00000003 BUSY Busy bit 4 1 OFFU Output FIFO full 3 1 OFNE Output FIFO not empty 2 1 IFNF Input FIFO not full 1 1 IFEM Input FIFO empty 0 1 DIN DIN data input register 0x8 0x20 read-write 0x00000000 DATAIN Data input 0 32 DOUT DOUT data output register 0xC 0x20 read-only 0x00000000 DATAOUT Data output 0 32 DMACR DMACR DMA control register 0x10 0x20 read-write 0x00000000 DOEN DMA output enable 1 1 DIEN DMA input enable 0 1 IMSCR IMSCR interrupt mask set/clear register 0x14 0x20 read-write 0x00000000 OUTIM Output FIFO service interrupt mask 1 1 INIM Input FIFO service interrupt mask 0 1 RISR RISR raw interrupt status register 0x18 0x20 read-only 0x00000001 OUTRIS Output FIFO service raw interrupt status 1 1 INRIS Input FIFO service raw interrupt status 0 1 MISR MISR masked interrupt status register 0x1C 0x20 read-only 0x00000000 OUTMIS Output FIFO service masked interrupt status 1 1 INMIS Input FIFO service masked interrupt status 0 1 4 0x8 0-3 KEY%s Cluster KEY%s, containing K?LR, K?RR 0x20 KLR K0LR key registers 0x0 0x20 write-only 0x00000000 b224 b224 0 1 b225 b225 1 1 b226 b226 2 1 b227 b227 3 1 b228 b228 4 1 b229 b229 5 1 b230 b230 6 1 b231 b231 7 1 b232 b232 8 1 b233 b233 9 1 b234 b234 10 1 b235 b235 11 1 b236 b236 12 1 b237 b237 13 1 b238 b238 14 1 b239 b239 15 1 b240 b240 16 1 b241 b241 17 1 b242 b242 18 1 b243 b243 19 1 b244 b244 20 1 b245 b245 21 1 b246 b246 22 1 b247 b247 23 1 b248 b248 24 1 b249 b249 25 1 b250 b250 26 1 b251 b251 27 1 b252 b252 28 1 b253 b253 29 1 b254 b254 30 1 b255 b255 31 1 KRR K0RR key registers 0x4 0x20 write-only 0x00000000 b192 b192 0 1 b193 b193 1 1 b194 b194 2 1 b195 b195 3 1 b196 b196 4 1 b197 b197 5 1 b198 b198 6 1 b199 b199 7 1 b200 b200 8 1 b201 b201 9 1 b202 b202 10 1 b203 b203 11 1 b204 b204 12 1 b205 b205 13 1 b206 b206 14 1 b207 b207 15 1 b208 b208 16 1 b209 b209 17 1 b210 b210 18 1 b211 b211 19 1 b212 b212 20 1 b213 b213 21 1 b214 b214 22 1 b215 b215 23 1 b216 b216 24 1 b217 b217 25 1 b218 b218 26 1 b219 b219 27 1 b220 b220 28 1 b221 b221 29 1 b222 b222 30 1 b223 b223 31 1 2 0x8 0-1 INIT%s Cluster INIT%s, containing IV?LR, IV?RR 0x40 IVLR IV0LR initialization vector registers 0x0 0x20 read-write 0x00000000 IV31 IV31 0 1 IV30 IV30 1 1 IV29 IV29 2 1 IV28 IV28 3 1 IV27 IV27 4 1 IV26 IV26 5 1 IV25 IV25 6 1 IV24 IV24 7 1 IV23 IV23 8 1 IV22 IV22 9 1 IV21 IV21 10 1 IV20 IV20 11 1 IV19 IV19 12 1 IV18 IV18 13 1 IV17 IV17 14 1 IV16 IV16 15 1 IV15 IV15 16 1 IV14 IV14 17 1 IV13 IV13 18 1 IV12 IV12 19 1 IV11 IV11 20 1 IV10 IV10 21 1 IV9 IV9 22 1 IV8 IV8 23 1 IV7 IV7 24 1 IV6 IV6 25 1 IV5 IV5 26 1 IV4 IV4 27 1 IV3 IV3 28 1 IV2 IV2 29 1 IV1 IV1 30 1 IV0 IV0 31 1 IVRR IV0RR initialization vector registers 0x4 0x20 read-write 0x00000000 IV63 IV63 0 1 IV62 IV62 1 1 IV61 IV61 2 1 IV60 IV60 3 1 IV59 IV59 4 1 IV58 IV58 5 1 IV57 IV57 6 1 IV56 IV56 7 1 IV55 IV55 8 1 IV54 IV54 9 1 IV53 IV53 10 1 IV52 IV52 11 1 IV51 IV51 12 1 IV50 IV50 13 1 IV49 IV49 14 1 IV48 IV48 15 1 IV47 IV47 16 1 IV46 IV46 17 1 IV45 IV45 18 1 IV44 IV44 19 1 IV43 IV43 20 1 IV42 IV42 21 1 IV41 IV41 22 1 IV40 IV40 23 1 IV39 IV39 24 1 IV38 IV38 25 1 IV37 IV37 26 1 IV36 IV36 27 1 IV35 IV35 28 1 IV34 IV34 29 1 IV33 IV33 30 1 IV32 IV32 31 1 8 0x4 0-7 CSGCMCCM%sR CSGCMCCM%sR context swap register 0x50 0x20 read-write 0x00000000 CSGCMCCMR CSGCMCCM0R 0 32 8 0x4 0-7 CSGCM%sR CSGCM%sR context swap register 0x70 0x20 read-write 0x00000000 CSGCMR CSGCM0R 0 32 DCMI Digital camera interface DCMI 0x50050000 0x0 0x400 registers DCMI DCMI global interrupt 78 CR CR control register 1 0x0 0x20 read-write 0x00000000 ENABLE DCMI enable 14 1 ENABLE Disabled DCMI disabled 0 Enabled DCMI enabled 1 EDM Extended data mode 10 2 EDM BitWidth8 Interface captures 8-bit data on every pixel clock 0 BitWidth10 Interface captures 10-bit data on every pixel clock 1 BitWidth12 Interface captures 12-bit data on every pixel clock 2 BitWidth14 Interface captures 14-bit data on every pixel clock 3 FCRC Frame capture rate control 8 2 FCRC All All frames are captured 0 Alternate Every alternate frame captured (50% bandwidth reduction) 1 OneOfFour One frame out of four captured (75% bandwidth reduction) 2 VSPOL Vertical synchronization polarity 7 1 VSPOL ActiveLow DCMI_VSYNC active low 0 ActiveHigh DCMI_VSYNC active high 1 HSPOL Horizontal synchronization polarity 6 1 HSPOL ActiveLow DCMI_HSYNC active low 0 ActiveHigh DCMI_HSYNC active high 1 PCKPOL Pixel clock polarity 5 1 PCKPOL FallingEdge Falling edge active 0 RisingEdge Rising edge active 1 ESS Embedded synchronization select 4 1 ESS Hardware Hardware synchronization data capture (frame/line start/stop) is synchronized with the DCMI_HSYNC/DCMI_VSYNC signals 0 Embedded Embedded synchronization data capture is synchronized with synchronization codes embedded in the data flow 1 JPEG JPEG format 3 1 JPEG Uncompressed Uncompressed video format 0 JPEG This bit is used for JPEG data transfers. The DCMI_HSYNC signal is used as data enable. The crop and embedded synchronization features (ESS bit) cannot be used in this mode 1 CROP Crop feature 2 1 CROP Full The full image is captured. In this case the total number of bytes in an image frame must be a multiple of four 0 Cropped Only the data inside the window specified by the crop register is captured. If the size of the crop window exceeds the picture size, then only the picture size is captured 1 CM Capture mode 1 1 CM Continuous Continuous grab mode - The received data are transferred into the destination memory through the DMA. The buffer location and mode (linear or circular buffer) is controlled through the system DMA 0 Snapshot Snapshot mode (single frame) - Once activated, the interface waits for the start of frame and then transfers a single frame through the DMA. At the end of the frame, the CAPTURE bit is automatically reset 1 CAPTURE Capture enable 0 1 CAPTURE Disabled Capture disabled 0 Enabled Capture enabled 1 SR SR status register 0x4 0x20 read-only 0x00000000 FNE FIFO not empty 2 1 FNE NotEmpty FIFO contains valid data 0 Empty FIFO empty 1 VSYNC VSYNC 1 1 VSYNC ActiveFrame Active frame 0 BetweenFrames Synchronization between frames 1 HSYNC HSYNC 0 1 HSYNC ActiveLine Active line 0 BetweenLines Synchronization between lines 1 RIS RIS raw interrupt status register 0x8 0x20 read-only 0x00000000 LINE_RIS Line raw interrupt status 4 1 LINE_RIS Cleared Interrupt cleared 0 Set Interrupt set 1 VSYNC_RIS VSYNC raw interrupt status 3 1 VSYNC_RIS Cleared Interrupt cleared 0 Set Interrupt set 1 ERR_RIS Synchronization error raw interrupt status 2 1 ERR_RIS NoError No synchronization error detected 0 SynchronizationError Embedded synchronization characters are not received in the correct order 1 OVR_RIS Overrun raw interrupt status 1 1 OVR_RIS NoOverrun No data buffer overrun occurred 0 OverrunOccured A data buffer overrun occurred and the data FIFO is corrupted. The bit is cleared by setting the OVR_ISC bit of the DCMI_ICR register 1 FRAME_RIS Capture complete raw interrupt status 0 1 FRAME_RIS NoNewCapture No new capture 0 FrameCaptured A frame has been captured 1 IER IER interrupt enable register 0xC 0x20 read-write 0x00000000 LINE_IE Line interrupt enable 4 1 LINE_IE Disabled No interrupt generation when the line is received 0 Enabled An Interrupt is generated when a line has been completely received 1 VSYNC_IE VSYNC interrupt enable 3 1 VSYNC_IE Disabled No interrupt generation 0 Enabled An interrupt is generated on each DCMI_VSYNC transition from the inactive to the active state 1 ERR_IE Synchronization error interrupt enable 2 1 ERR_IE Disabled No interrupt generation 0 Enabled An interrupt is generated if the embedded synchronization codes are not received in the correct order 1 OVR_IE Overrun interrupt enable 1 1 OVR_IE Disabled No interrupt generation 0 Enabled An interrupt is generated if the DMA was not able to transfer the last data before new data (32-bit) are received 1 FRAME_IE Capture complete interrupt enable 0 1 FRAME_IE Disabled No interrupt generation 0 Enabled An interrupt is generated at the end of each received frame/crop window (in crop mode) 1 MIS MIS masked interrupt status register 0x10 0x20 read-only 0x00000000 LINE_MIS Line masked interrupt status 4 1 LINE_MIS Disabled No interrupt generation when the line is received 0 Enabled An Interrupt is generated when a line has been completely received and the LINE_IE bit is set in DCMI_IER 1 VSYNC_MIS VSYNC masked interrupt status 3 1 VSYNC_MIS Disabled No interrupt is generated on DCMI_VSYNC transitions 0 Enabled An interrupt is generated on each DCMI_VSYNC transition from the inactive to the active state and the VSYNC_IE bit is set in DCMI_IER 1 ERR_MIS Synchronization error masked interrupt status 2 1 ERR_MIS Disabled No interrupt is generated on a synchronization error 0 Enabled An interrupt is generated if the embedded synchronization codes are not received in the correct order and the ERR_IE bit in DCMI_IER is set 1 OVR_MIS Overrun masked interrupt status 1 1 OVR_MIS Disabled No interrupt is generated on overrun 0 Enabled An interrupt is generated if the DMA was not able to transfer the last data before new data (32-bit) are received and the OVR_IE bit is set in DCMI_IER 1 FRAME_MIS Capture complete masked interrupt status 0 1 FRAME_MIS Disabled No interrupt is generated after a complete capture 0 Enabled An interrupt is generated at the end of each received frame/crop window (in crop mode) and the FRAME_IE bit is set in DCMI_IER 1 ICR ICR interrupt clear register 0x14 0x20 write-only 0x00000000 LINE_ISC line interrupt status clear 4 1 LINE_ISC Clear Setting this bit clears the LINE_RIS flag in the DCMI_RIS register 1 VSYNC_ISC Vertical synch interrupt status clear 3 1 VSYNC_ISC Clear Setting this bit clears the VSYNC_RIS flag in the DCMI_RIS register 1 ERR_ISC Synchronization error interrupt status clear 2 1 ERR_ISC Clear Setting this bit clears the ERR_RIS flag in the DCMI_RIS register 1 OVR_ISC Overrun interrupt status clear 1 1 OVR_ISC Clear Setting this bit clears the OVR_RIS flag in the DCMI_RIS register 1 FRAME_ISC Capture complete interrupt status clear 0 1 FRAME_ISC Clear Setting this bit clears the FRAME_RIS flag in the DCMI_RIS register 1 ESCR ESCR embedded synchronization code register 0x18 0x20 read-write 0x00000000 FEC Frame end delimiter code 24 8 LEC Line end delimiter code 16 8 LSC Line start delimiter code 8 8 FSC Frame start delimiter code 0 8 ESUR ESUR embedded synchronization unmask register 0x1C 0x20 read-write 0x00000000 FEU Frame end delimiter unmask 24 8 LEU Line end delimiter unmask 16 8 LSU Line start delimiter unmask 8 8 FSU Frame start delimiter unmask 0 8 CWSTRT CWSTRT crop window start 0x20 0x20 read-write 0x00000000 VST Vertical start line count 16 13 0 8191 HOFFCNT Horizontal offset count 0 14 0 16383 CWSIZE CWSIZE crop window size 0x24 0x20 read-write 0x00000000 VLINE Vertical line count 16 14 0 16383 CAPCNT Capture count 0 14 0 16383 DR DR data register 0x28 0x20 read-only 0x00000000 4 0x8 0-3 BYTE%s Data byte %s 0 8 0 255 FMC Flexible memory controller FSMC 0xA0000000 0x0 0x1000 registers FMC FMC global interrupt 48 BCR1 BCR1 SRAM/NOR-Flash chip-select control register 1 0x0 0x20 read-write 0x000030D0 CCLKEN CCLKEN 20 1 CCLKEN Disabled The FMC_CLK is generated continuously during asynchronous and synchronous access. The FMC_CLK clock is activated when the CCLKEN is set 0 Enabled The FMC_CLK is only generated during the synchronous memory access (read/write transaction) 1 CBURSTRW CBURSTRW 19 1 CBURSTRW Disabled Write operations are always performed in asynchronous mode 0 Enabled Write operations are performed in synchronous mode 1 ASYNCWAIT ASYNCWAIT 15 1 ASYNCWAIT Disabled Wait signal not used in asynchronous mode 0 Enabled Wait signal used even in asynchronous mode 1 EXTMOD EXTMOD 14 1 EXTMOD Disabled Values inside the FMC_BWTR are not taken into account 0 Enabled Values inside the FMC_BWTR are taken into account 1 WAITEN WAITEN 13 1 WAITEN Disabled Values inside the FMC_BWTR are taken into account 0 Enabled NWAIT signal enabled 1 WREN WREN 12 1 WREN Disabled Write operations disabled for the bank by the FMC 0 Enabled Write operations enabled for the bank by the FMC 1 WAITCFG WAITCFG 11 1 WAITCFG BeforeWaitState NWAIT signal is active one data cycle before wait state 0 DuringWaitState NWAIT signal is active during wait state 1 WAITPOL WAITPOL 9 1 WAITPOL ActiveLow NWAIT active low 0 ActiveHigh NWAIT active high 1 BURSTEN BURSTEN 8 1 BURSTEN Disabled Burst mode disabled 0 Enabled Burst mode enabled 1 FACCEN FACCEN 6 1 FACCEN Disabled Corresponding NOR Flash memory access is disabled 0 Enabled Corresponding NOR Flash memory access is enabled 1 MWID MWID 4 2 MWID Bits8 Memory data bus width 8 bits 0 Bits16 Memory data bus width 16 bits 1 Bits32 Memory data bus width 32 bits 2 MTYP MTYP 2 2 MTYP SRAM SRAM memory type 0 PSRAM PSRAM (CRAM) memory type 1 Flash NOR Flash/OneNAND Flash 2 MUXEN MUXEN 1 1 MUXEN Disabled Address/Data non-multiplexed 0 Enabled Address/Data multiplexed on databus 1 MBKEN MBKEN 0 1 MBKEN Disabled Corresponding memory bank is disabled 0 Enabled Corresponding memory bank is enabled 1 WRAPMOD WRAPMOD 10 1 WRAPMOD Disabled Direct wrapped burst is not enabled 0 Enabled Direct wrapped burst is enabled 1 WFDIS Write FIFO disable 21 1 read-write WFDIS Enabled Write FIFO enabled 0 Disabled Write FIFO disabled 1 CPSIZE CRAM page size 16 3 read-write CPSIZE NoBurstSplit No burst split when crossing page boundary 0 Bytes128 128 bytes CRAM page size 1 Bytes256 256 bytes CRAM page size 2 Bytes512 512 bytes CRAM page size 3 Bytes1024 1024 bytes CRAM page size 4 4 0x8 1-4 BTR%s BTR%s SRAM/NOR-Flash chip-select timing register %s 0x4 0x20 read-write 0xFFFFFFFF ACCMOD ACCMOD 28 2 ACCMOD A Access mode A 0 B Access mode B 1 C Access mode C 2 D Access mode D 3 DATLAT DATLAT 24 4 0 15 CLKDIV CLKDIV 20 4 1 15 BUSTURN BUSTURN 16 4 0 15 DATAST DATAST 8 8 1 255 ADDHLD ADDHLD 4 4 1 15 ADDSET ADDSET 0 4 0 15 3 0x8 2-4 BCR%s BCR%s SRAM/NOR-Flash chip-select control register %s 0x8 0x20 read-write 0x000030D0 CBURSTRW CBURSTRW 19 1 ASYNCWAIT ASYNCWAIT 15 1 EXTMOD EXTMOD 14 1 WAITEN WAITEN 13 1 WREN WREN 12 1 WAITCFG WAITCFG 11 1 WRAPMOD WRAPMOD 10 1 WAITPOL WAITPOL 9 1 BURSTEN BURSTEN 8 1 FACCEN FACCEN 6 1 MWID MWID 4 2 MTYP MTYP 2 2 MUXEN MUXEN 1 1 MBKEN MBKEN 0 1 CPSIZE CRAM page size 16 3 read-write PCR PCR PC Card/NAND Flash control register 0x80 0x20 read-write 0x00000018 ECCPS ECCPS 17 3 ECCPS Bytes256 ECC page size 256 bytes 0 Bytes512 ECC page size 512 bytes 1 Bytes1024 ECC page size 1024 bytes 2 Bytes2048 ECC page size 2048 bytes 3 Bytes4096 ECC page size 4096 bytes 4 Bytes8192 ECC page size 8192 bytes 5 TAR TAR 13 4 0 15 TCLR TCLR 9 4 0 15 ECCEN ECCEN 6 1 ECCEN Disabled ECC logic is disabled and reset 0 Enabled ECC logic is enabled 1 PWID PWID 4 2 PWID Bits8 External memory device width 8 bits 0 Bits16 External memory device width 16 bits 1 PTYP PTYP 3 1 PTYP NANDFlash NAND Flash 1 PBKEN PBKEN 2 1 PBKEN Disabled Corresponding memory bank is disabled 0 Enabled Corresponding memory bank is enabled 1 PWAITEN PWAITEN 1 1 PWAITEN Disabled Wait feature disabled 0 Enabled Wait feature enabled 1 SR SR FIFO status and interrupt register 0x84 0x20 0x00000040 FEMPT FEMPT 6 1 read-only FEMPT NotEmpty FIFO not empty 0 Empty FIFO empty 1 IFEN IFEN 5 1 read-write IFEN Disabled Interrupt falling edge detection request disabled 0 Enabled Interrupt falling edge detection request enabled 1 ILEN ILEN 4 1 read-write ILEN Disabled Interrupt high-level detection request disabled 0 Enabled Interrupt high-level detection request enabled 1 IREN IREN 3 1 read-write IREN Disabled Interrupt rising edge detection request disabled 0 Enabled Interrupt rising edge detection request enabled 1 IFS IFS 2 1 read-write IFS DidNotOccur Interrupt falling edge did not occur 0 Occurred Interrupt falling edge occurred 1 ILS ILS 1 1 read-write ILS DidNotOccur Interrupt high-level did not occur 0 Occurred Interrupt high-level occurred 1 IRS IRS 0 1 read-write IRS DidNotOccur Interrupt rising edge did not occur 0 Occurred Interrupt rising edge occurred 1 PMEM PMEM Common memory space timing register 0x88 0x20 read-write 0xFCFCFCFC MEMHIZ MEMHIZx 24 8 0 254 MEMHOLD MEMHOLDx 16 8 1 254 MEMWAIT MEMWAITx 8 8 1 254 MEMSET MEMSETx 0 8 0 254 PATT PATT Attribute memory space timing register 0x8C 0x20 read-write 0xFCFCFCFC ATTHIZ ATTHIZx 24 8 0 254 ATTHOLD ATTHOLDx 16 8 1 254 ATTWAIT ATTWAITx 8 8 1 254 ATTSET ATTSETx 0 8 0 254 ECCR ECCR ECC result register 0x94 0x20 read-only 0x00000000 ECC ECCx 0 32 0 4294967295 4 0x8 1-4 BWTR%s BWTR%s SRAM/NOR-Flash write timing registers %s 0x104 0x20 read-write 0x0FFFFFFF ACCMOD ACCMOD 28 2 ACCMOD A Access mode A 0 B Access mode B 1 C Access mode C 2 D Access mode D 3 DATAST DATAST 8 8 1 255 ADDHLD ADDHLD 4 4 1 15 ADDSET ADDSET 0 4 0 15 BUSTURN Bus turnaround phase duration 16 4 read-write 0 15 SDCR1 SDCR1 SDRAM Control Register 1 0x140 0x20 read-write 0x000002D0 NC Number of column address bits 0 2 NC Bits8 8 bits 0 Bits9 9 bits 1 Bits10 10 bits 2 Bits11 11 bits 3 NR Number of row address bits 2 2 NR Bits11 11 bits 0 Bits12 12 bits 1 Bits13 13 bits 2 MWID Memory data bus width 4 2 MWID Bits8 Memory data bus width 8 bits 0 Bits16 Memory data bus width 16 bits 1 Bits32 Memory data bus width 32 bits 2 NB Number of internal banks 6 1 NB NB2 Two internal Banks 0 NB4 Four internal Banks 1 CAS CAS latency 7 2 CAS Clocks1 1 cycle 1 Clocks2 2 cycles 2 Clocks3 3 cycles 3 WP Write protection 9 1 WP Disabled Write accesses allowed 0 Enabled Write accesses ignored 1 SDCLK SDRAM clock configuration 10 2 SDCLK Disabled SDCLK clock disabled 0 Div2 SDCLK period = 2 x HCLK period 2 Div3 SDCLK period = 3 x HCLK period 3 RBURST Burst read 12 1 RBURST Disabled Single read requests are not managed as bursts 0 Enabled Single read requests are always managed as bursts 1 RPIPE Read pipe 13 2 RPIPE NoDelay No clock cycle delay 0 Clocks1 One clock cycle delay 1 Clocks2 Two clock cycles delay 2 SDCR2 SDCR2 SDRAM Control Register 2 0x144 0x20 read-write 0x000002D0 NC Number of column address bits 0 2 NR Number of row address bits 2 2 MWID Memory data bus width 4 2 NB Number of internal banks 6 1 CAS CAS latency 7 2 WP Write protection 9 1 SDCLK SDRAM clock configuration 10 2 RBURST Burst read 12 1 RBURST Disabled Single read requests are not managed as bursts 0 Enabled Single read requests are always managed as bursts 1 RPIPE Read pipe 13 2 RPIPE NoDelay No clock cycle delay 0 Clocks1 One clock cycle delay 1 Clocks2 Two clock cycles delay 2 2 0x4 1-2 SDTR%s SDTR%s SDRAM Timing register %s 0x148 0x20 read-write 0x0FFFFFFF TMRD Load Mode Register to Active 0 4 0 15 TXSR Exit self-refresh delay 4 4 0 15 TRAS Self refresh time 8 4 0 15 TRC Row cycle delay 12 4 0 15 TWR Recovery delay 16 4 0 15 TRP Row precharge delay 20 4 0 15 TRCD Row to column delay 24 4 0 15 SDCMR SDCMR SDRAM Command Mode register 0x150 0x20 0x00000000 MODE Command mode 0 3 write-only MODE Normal Normal Mode 0 ClockConfigurationEnable Clock Configuration Enable 1 PALL PALL (All Bank Precharge) command 2 AutoRefreshCommand Auto-refresh command 3 LoadModeRegister Load Mode Resgier 4 SelfRefreshCommand Self-refresh command 5 PowerDownCommand Power-down command 6 CTB2 Command target bank 2 3 1 write-only CTB2 NotIssued Command not issued to SDRAM Bank 1 0 Issued Command issued to SDRAM Bank 1 1 CTB1 Command target bank 1 4 1 write-only NRFS Number of Auto-refresh 5 4 read-write 0 15 MRD Mode Register definition 9 13 read-write 0 8191 SDRTR SDRTR SDRAM Refresh Timer register 0x154 0x20 0x00000000 CRE Clear Refresh error flag 0 1 write-only CRE Clear Refresh Error Flag is cleared 1 COUNT Refresh Timer Count 1 13 read-write 0 8191 REIE RES Interrupt Enable 14 1 read-write REIE Disabled Interrupt is disabled 0 Enabled Interrupt is generated if RE = 1 1 SDSR SDSR SDRAM Status register 0x158 0x20 read-only 0x00000000 RE Refresh error flag 0 1 RE NoError No refresh error has been detected 0 Error A refresh error has been detected 1 MODES1 Status Mode for Bank 1 1 2 MODES1 Normal Normal Mode 0 SelfRefresh Self-refresh mode 1 PowerDown Power-down mode 2 MODES2 Status Mode for Bank 2 3 2 BUSY Busy status 5 1 BUSY NotBusy SDRAM Controller is ready to accept a new request 0 Busy SDRAM Controller is not ready to accept a new request 1 DBGMCU Debug support DBG 0xE0042000 0x0 0x400 registers IDCODE IDCODE IDCODE 0x0 0x20 read-only 0x10006411 DEV_ID DEV_ID 0 12 REV_ID REV_ID 16 16 CR CR Control Register 0x4 0x20 read-write 0x00000000 DBG_SLEEP DBG_SLEEP 0 1 DBG_STOP DBG_STOP 1 1 DBG_STANDBY DBG_STANDBY 2 1 TRACE_IOEN TRACE_IOEN 5 1 TRACE_IOEN Disabled Trace pins not assigned (default state) 0 Enabled Trace pins assigned 1 TRACE_MODE TRACE_MODE 6 2 TRACE_MODE Asynchronous TRACE pin assignment for Asynchronous Mode 0 Size1 TRACE pin assignment for Synchronous Mode with a TRACEDATA size of 1 1 Size2 TRACE pin assignment for Synchronous Mode with a TRACEDATA size of 2 2 Size4 TRACE pin assignment for Synchronous Mode with a TRACEDATA size of 4 3 APB1_FZ APB1_FZ Debug MCU APB1 Freeze registe 0x8 0x20 read-write 0x00000000 DBG_TIM2_STOP DBG_TIM2_STOP 0 1 DBG_TIM3_STOP DBG_TIM3 _STOP 1 1 DBG_TIM4_STOP DBG_TIM4_STOP 2 1 DBG_TIM5_STOP DBG_TIM5_STOP 3 1 DBG_TIM6_STOP DBG_TIM6_STOP 4 1 DBG_TIM7_STOP DBG_TIM7_STOP 5 1 DBG_TIM12_STOP DBG_TIM12_STOP 6 1 DBG_TIM13_STOP DBG_TIM13_STOP 7 1 DBG_TIM14_STOP DBG_TIM14_STOP 8 1 DBG_WWDG_STOP DBG_WWDG_STOP 11 1 DBG_IWDG_STOP DBG_IWDEG_STOP 12 1 DBG_J2C1_SMBUS_TIMEOUT DBG_J2C1_SMBUS_TIMEOUT 21 1 DBG_J2C2_SMBUS_TIMEOUT DBG_J2C2_SMBUS_TIMEOUT 22 1 DBG_J2C3SMBUS_TIMEOUT DBG_J2C3SMBUS_TIMEOUT 23 1 DBG_CAN1_STOP DBG_CAN1_STOP 25 1 DBG_CAN2_STOP DBG_CAN2_STOP 26 1 APB2_FZ APB2_FZ Debug MCU APB2 Freeze registe 0xC 0x20 read-write 0x00000000 DBG_TIM1_STOP TIM1 counter stopped when core is halted 0 1 DBG_TIM8_STOP TIM8 counter stopped when core is halted 1 1 DBG_TIM9_STOP TIM9 counter stopped when core is halted 16 1 DBG_TIM10_STOP TIM10 counter stopped when core is halted 17 1 DBG_TIM11_STOP TIM11 counter stopped when core is halted 18 1 DMA2 DMA controller DMA 0x40026400 0x0 0x400 registers DMA2_Stream0 DMA2 Stream0 global interrupt 56 DMA2_Stream1 DMA2 Stream1 global interrupt 57 DMA2_Stream2 DMA2 Stream2 global interrupt 58 DMA2_Stream3 DMA2 Stream3 global interrupt 59 DMA2_Stream4 DMA2 Stream4 global interrupt 60 DMA2_Stream5 DMA2 Stream5 global interrupt 68 DMA2_Stream6 DMA2 Stream6 global interrupt 69 DMA2_Stream7 DMA2 Stream7 global interrupt 70 LISR LISR low interrupt status register 0x0 0x20 read-only 0x00000000 TCIF0 Stream x transfer complete interrupt flag (x = 3..0) 5 1 TCIF0 NotComplete No transfer complete event on stream x 0 Complete A transfer complete event occurred on stream x 1 TCIF3 Stream x transfer complete interrupt flag (x = 3..0) 27 1 HTIF0 Stream x half transfer interrupt flag (x=3..0) 4 1 HTIF0 NotHalf No half transfer event on stream x 0 Half A half transfer event occurred on stream x 1 HTIF3 Stream x half transfer interrupt flag (x=3..0) 26 1 TEIF0 Stream x transfer error interrupt flag (x=3..0) 3 1 TEIF0 NoError No transfer error on stream x 0 Error A transfer error occurred on stream x 1 TEIF3 Stream x transfer error interrupt flag (x=3..0) 25 1 DMEIF0 Stream x direct mode error interrupt flag (x=3..0) 2 1 DMEIF0 NoError No Direct Mode error on stream x 0 Error A Direct Mode error occurred on stream x 1 DMEIF3 Stream x direct mode error interrupt flag (x=3..0) 24 1 FEIF0 Stream x FIFO error interrupt flag (x=3..0) 0 1 FEIF0 NoError No FIFO error event on stream x 0 Error A FIFO error event occurred on stream x 1 FEIF3 Stream x FIFO error interrupt flag (x=3..0) 22 1 TCIF2 Stream x transfer complete interrupt flag (x = 3..0) 21 1 HTIF2 Stream x half transfer interrupt flag (x=3..0) 20 1 TEIF2 Stream x transfer error interrupt flag (x=3..0) 19 1 DMEIF2 Stream x direct mode error interrupt flag (x=3..0) 18 1 FEIF2 Stream x FIFO error interrupt flag (x=3..0) 16 1 TCIF1 Stream x transfer complete interrupt flag (x = 3..0) 11 1 HTIF1 Stream x half transfer interrupt flag (x=3..0) 10 1 TEIF1 Stream x transfer error interrupt flag (x=3..0) 9 1 DMEIF1 Stream x direct mode error interrupt flag (x=3..0) 8 1 FEIF1 Stream x FIFO error interrupt flag (x=3..0) 6 1 HISR HISR high interrupt status register 0x4 0x20 read-only 0x00000000 TCIF4 Stream x transfer complete interrupt flag (x=7..4) 5 1 TCIF4 NotComplete No transfer complete event on stream x 0 Complete A transfer complete event occurred on stream x 1 TCIF7 Stream x transfer complete interrupt flag (x=7..4) 27 1 HTIF4 Stream x half transfer interrupt flag (x=7..4) 4 1 HTIF4 NotHalf No half transfer event on stream x 0 Half A half transfer event occurred on stream x 1 HTIF7 Stream x half transfer interrupt flag (x=7..4) 26 1 TEIF4 Stream x transfer error interrupt flag (x=7..4) 3 1 TEIF4 NoError No transfer error on stream x 0 Error A transfer error occurred on stream x 1 TEIF7 Stream x transfer error interrupt flag (x=7..4) 25 1 DMEIF4 Stream x direct mode error interrupt flag (x=7..4) 2 1 DMEIF4 NoError No Direct Mode error on stream x 0 Error A Direct Mode error occurred on stream x 1 DMEIF7 Stream x direct mode error interrupt flag (x=7..4) 24 1 FEIF4 Stream x FIFO error interrupt flag (x=7..4) 0 1 FEIF4 NoError No FIFO error event on stream x 0 Error A FIFO error event occurred on stream x 1 FEIF7 Stream x FIFO error interrupt flag (x=7..4) 22 1 TCIF6 Stream x transfer complete interrupt flag (x=7..4) 21 1 HTIF6 Stream x half transfer interrupt flag (x=7..4) 20 1 TEIF6 Stream x transfer error interrupt flag (x=7..4) 19 1 DMEIF6 Stream x direct mode error interrupt flag (x=7..4) 18 1 FEIF6 Stream x FIFO error interrupt flag (x=7..4) 16 1 TCIF5 Stream x transfer complete interrupt flag (x=7..4) 11 1 HTIF5 Stream x half transfer interrupt flag (x=7..4) 10 1 TEIF5 Stream x transfer error interrupt flag (x=7..4) 9 1 DMEIF5 Stream x direct mode error interrupt flag (x=7..4) 8 1 FEIF5 Stream x FIFO error interrupt flag (x=7..4) 6 1 LIFCR LIFCR low interrupt flag clear register 0x8 0x20 write-only 0x00000000 CTCIF0 Stream x clear transfer complete interrupt flag (x = 3..0) 5 1 CTCIF0 Clear Clear the corresponding TCIFx flag 1 CTCIF3 Stream x clear transfer complete interrupt flag (x = 3..0) 27 1 CHTIF0 Stream x clear half transfer interrupt flag (x = 3..0) 4 1 CHTIF0 Clear Clear the corresponding HTIFx flag 1 CHTIF3 Stream x clear half transfer interrupt flag (x = 3..0) 26 1 CTEIF0 Stream x clear transfer error interrupt flag (x = 3..0) 3 1 CTEIF0 Clear Clear the corresponding TEIFx flag 1 CTEIF3 Stream x clear transfer error interrupt flag (x = 3..0) 25 1 CDMEIF0 Stream x clear direct mode error interrupt flag (x = 3..0) 2 1 CDMEIF0 Clear Clear the corresponding DMEIFx flag 1 CDMEIF3 Stream x clear direct mode error interrupt flag (x = 3..0) 24 1 CFEIF0 Stream x clear FIFO error interrupt flag (x = 3..0) 0 1 CFEIF0 Clear Clear the corresponding CFEIFx flag 1 CFEIF3 Stream x clear FIFO error interrupt flag (x = 3..0) 22 1 CTCIF2 Stream x clear transfer complete interrupt flag (x = 3..0) 21 1 CHTIF2 Stream x clear half transfer interrupt flag (x = 3..0) 20 1 CTEIF2 Stream x clear transfer error interrupt flag (x = 3..0) 19 1 CDMEIF2 Stream x clear direct mode error interrupt flag (x = 3..0) 18 1 CFEIF2 Stream x clear FIFO error interrupt flag (x = 3..0) 16 1 CTCIF1 Stream x clear transfer complete interrupt flag (x = 3..0) 11 1 CHTIF1 Stream x clear half transfer interrupt flag (x = 3..0) 10 1 CTEIF1 Stream x clear transfer error interrupt flag (x = 3..0) 9 1 CDMEIF1 Stream x clear direct mode error interrupt flag (x = 3..0) 8 1 CFEIF1 Stream x clear FIFO error interrupt flag (x = 3..0) 6 1 HIFCR HIFCR high interrupt flag clear register 0xC 0x20 write-only 0x00000000 CTCIF4 Stream x clear transfer complete interrupt flag (x = 7..4) 5 1 CTCIF4 Clear Clear the corresponding TCIFx flag 1 CTCIF7 Stream x clear transfer complete interrupt flag (x = 7..4) 27 1 CHTIF4 Stream x clear half transfer interrupt flag (x = 7..4) 4 1 CHTIF4 Clear Clear the corresponding HTIFx flag 1 CHTIF7 Stream x clear half transfer interrupt flag (x = 7..4) 26 1 CTEIF4 Stream x clear transfer error interrupt flag (x = 7..4) 3 1 CTEIF4 Clear Clear the corresponding TEIFx flag 1 CTEIF7 Stream x clear transfer error interrupt flag (x = 7..4) 25 1 CDMEIF4 Stream x clear direct mode error interrupt flag (x = 7..4) 2 1 CDMEIF4 Clear Clear the corresponding DMEIFx flag 1 CDMEIF7 Stream x clear direct mode error interrupt flag (x = 7..4) 24 1 CFEIF4 Stream x clear FIFO error interrupt flag (x = 7..4) 0 1 CFEIF4 Clear Clear the corresponding CFEIFx flag 1 CFEIF7 Stream x clear FIFO error interrupt flag (x = 7..4) 22 1 CTCIF6 Stream x clear transfer complete interrupt flag (x = 7..4) 21 1 CHTIF6 Stream x clear half transfer interrupt flag (x = 7..4) 20 1 CTEIF6 Stream x clear transfer error interrupt flag (x = 7..4) 19 1 CDMEIF6 Stream x clear direct mode error interrupt flag (x = 7..4) 18 1 CFEIF6 Stream x clear FIFO error interrupt flag (x = 7..4) 16 1 CTCIF5 Stream x clear transfer complete interrupt flag (x = 7..4) 11 1 CHTIF5 Stream x clear half transfer interrupt flag (x = 7..4) 10 1 CTEIF5 Stream x clear transfer error interrupt flag (x = 7..4) 9 1 CDMEIF5 Stream x clear direct mode error interrupt flag (x = 7..4) 8 1 CFEIF5 Stream x clear FIFO error interrupt flag (x = 7..4) 6 1 8 0x18 0-7 ST%s Stream cluster: S?CR, S?NDTR, S?M0AR, S?M1AR and S?FCR registers 0x10 CR S0CR stream x configuration register 0x0 0x20 read-write 0x00000000 CHSEL Channel selection 25 3 0 7 PBURST Peripheral burst transfer configuration 21 2 PBURST Single Single transfer 0 INCR4 Incremental burst of 4 beats 1 INCR8 Incremental burst of 8 beats 2 INCR16 Incremental burst of 16 beats 3 MBURST Memory burst transfer configuration 23 2 CT Current target (only in double buffer mode) 19 1 CT Memory0 The current target memory is Memory 0 0 Memory1 The current target memory is Memory 1 1 DBM Double buffer mode 18 1 DBM Disabled No buffer switching at the end of transfer 0 Enabled Memory target switched at the end of the DMA transfer 1 PL Priority level 16 2 PL Low Low 0 Medium Medium 1 High High 2 VeryHigh Very high 3 PINCOS Peripheral increment offset size 15 1 PINCOS PSIZE The offset size for the peripheral address calculation is linked to the PSIZE 0 Fixed4 The offset size for the peripheral address calculation is fixed to 4 (32-bit alignment) 1 PSIZE Peripheral data size 11 2 PSIZE Bits8 Byte (8-bit) 0 Bits16 Half-word (16-bit) 1 Bits32 Word (32-bit) 2 MSIZE Memory data size 13 2 PINC Peripheral increment mode 9 1 PINC Fixed Address pointer is fixed 0 Incremented Address pointer is incremented after each data transfer 1 MINC Memory increment mode 10 1 CIRC Circular mode 8 1 CIRC Disabled Circular mode disabled 0 Enabled Circular mode enabled 1 DIR Data transfer direction 6 2 DIR PeripheralToMemory Peripheral-to-memory 0 MemoryToPeripheral Memory-to-peripheral 1 MemoryToMemory Memory-to-memory 2 PFCTRL Peripheral flow controller 5 1 PFCTRL DMA The DMA is the flow controller 0 Peripheral The peripheral is the flow controller 1 TCIE Transfer complete interrupt enable 4 1 TCIE Disabled TC interrupt disabled 0 Enabled TC interrupt enabled 1 HTIE Half transfer interrupt enable 3 1 HTIE Disabled HT interrupt disabled 0 Enabled HT interrupt enabled 1 TEIE Transfer error interrupt enable 2 1 TEIE Disabled TE interrupt disabled 0 Enabled TE interrupt enabled 1 DMEIE Direct mode error interrupt enable 1 1 DMEIE Disabled DME interrupt disabled 0 Enabled DME interrupt enabled 1 EN Stream enable / flag stream ready when read low 0 1 EN Disabled Stream disabled 0 Enabled Stream enabled 1 NDTR S0NDTR stream x number of data register 0x4 0x20 read-write 0x00000000 NDT Number of data items to transfer 0 16 0 65535 PAR S0PAR stream x peripheral address register 0x8 0x20 read-write 0x00000000 PA Peripheral address 0 32 M0AR S0M0AR stream x memory 0 address register 0xC 0x20 read-write 0x00000000 M0A Memory 0 address 0 32 M1AR S0M1AR stream x memory 1 address register 0x10 0x20 read-write 0x00000000 M1A Memory 1 address (used in case of Double buffer mode) 0 32 FCR S0FCR stream x FIFO control register 0x14 0x20 0x00000021 FEIE FIFO error interrupt enable 7 1 read-write FEIE Disabled FE interrupt disabled 0 Enabled FE interrupt enabled 1 FS FIFO status 3 3 read-only FS Quarter1 0 < fifo_level < 1/4 0 Quarter2 1/4 <= fifo_level < 1/2 1 Quarter3 1/2 <= fifo_level < 3/4 2 Quarter4 3/4 <= fifo_level < full 3 Empty FIFO is empty 4 Full FIFO is full 5 DMDIS Direct mode disable 2 1 read-write DMDIS Enabled Direct mode is enabled 0 Disabled Direct mode is disabled 1 FTH FIFO threshold selection 0 2 read-write FTH Quarter 1/4 full FIFO 0 Half 1/2 full FIFO 1 ThreeQuarters 3/4 full FIFO 2 Full Full FIFO 3 DMA1 0x40026000 DMA1_Stream0 DMA1 Stream0 global interrupt 11 DMA1_Stream1 DMA1 Stream1 global interrupt 12 DMA1_Stream2 DMA1 Stream2 global interrupt 13 DMA1_Stream3 DMA1 Stream3 global interrupt 14 DMA1_Stream4 DMA1 Stream4 global interrupt 15 DMA1_Stream5 DMA1 Stream5 global interrupt 16 DMA1_Stream6 DMA1 Stream6 global interrupt 17 DMA1_Stream7 DMA1 Stream7 global interrupt 47 RCC Reset and clock control RCC 0x40023800 0x0 0x400 registers RCC RCC global interrupt 5 CR CR clock control register 0x0 0x20 0x00000083 HSIRDY Internal high-speed clock ready flag 1 1 read-only HSIRDYR NotReady Clock not ready 0 Ready Clock ready 1 PLLI2SRDY PLLI2S clock ready flag 27 1 read-only HSION Internal high-speed clock enable 0 1 read-write HSION Off Clock Off 0 On Clock On 1 PLLI2SON PLLI2S enable 26 1 read-write PLLRDY Main PLL (PLL) clock ready flag 25 1 read-only PLLON Main PLL (PLL) enable 24 1 read-write CSSON Clock security system enable 19 1 read-write CSSON Off Clock security system disabled (clock detector OFF) 0 On Clock security system enable (clock detector ON if the HSE is ready, OFF if not) 1 HSEBYP HSE clock bypass 18 1 read-write HSEBYP NotBypassed HSE crystal oscillator not bypassed 0 Bypassed HSE crystal oscillator bypassed with external clock 1 HSERDY HSE clock ready flag 17 1 read-only HSEON HSE clock enable 16 1 read-write HSICAL Internal high-speed clock calibration 8 8 read-only 0 255 HSITRIM Internal high-speed clock trimming 3 5 read-write 0 31 PLLSAIRDY PLLSAI clock ready flag 29 1 read-only PLLSAION PLLSAI enable 28 1 read-write PLLCFGR PLLCFGR PLL configuration register 0x4 0x20 read-write 0x24003010 PLLQ Main PLL (PLL) division factor for USB OTG FS, SDIO and random number generator clocks 24 4 2 15 PLLSRC Main PLL(PLL) and audio PLL (PLLI2S) entry clock source 22 1 PLLSRC HSI HSI clock selected as PLL and PLLI2S clock entry 0 HSE HSE oscillator clock selected as PLL and PLLI2S clock entry 1 PLLP Main PLL (PLL) division factor for main system clock 16 2 PLLP Div2 PLLP=2 0 Div4 PLLP=4 1 Div6 PLLP=6 2 Div8 PLLP=8 3 PLLN Main PLL (PLL) multiplication factor for VCO 6 9 50 432 PLLM Division factor for the main PLL (PLL) and audio PLL (PLLI2S) input clock 0 6 2 63 CFGR CFGR clock configuration register 0x8 0x20 0x00000000 MCO2 Microcontroller clock output 2 30 2 read-write MCO2 SYSCLK System clock (SYSCLK) selected 0 PLLI2S PLLI2S clock selected 1 HSE HSE oscillator clock selected 2 PLL PLL clock selected 3 MCO1PRE MCO1 prescaler 24 3 read-write MCO1PRE Div2 Division by 2 4 Div3 Division by 3 5 Div4 Division by 4 6 Div5 Division by 5 7 Div1 No division true MCO2PRE MCO2 prescaler 27 3 read-write I2SSRC I2S clock selection 23 1 read-write I2SSRC PLLI2S PLLI2S clock used as I2S clock source 0 CKIN External clock mapped on the I2S_CKIN pin used as I2S clock source 1 MCO1 Microcontroller clock output 1 21 2 read-write MCO1 HSI HSI clock selected 0 LSE LSE oscillator selected 1 HSE HSE oscillator clock selected 2 PLL PLL clock selected 3 RTCPRE HSE division factor for RTC clock 16 5 read-write 0 31 PPRE1 APB Low speed prescaler (APB1) 10 3 read-write PPRE1 Div2 HCLK divided by 2 4 Div4 HCLK divided by 4 5 Div8 HCLK divided by 8 6 Div16 HCLK divided by 16 7 Div1 HCLK not divided true PPRE2 APB high-speed prescaler (APB2) 13 3 read-write HPRE AHB prescaler 4 4 read-write HPRE Div2 SYSCLK divided by 2 8 Div4 SYSCLK divided by 4 9 Div8 SYSCLK divided by 8 10 Div16 SYSCLK divided by 16 11 Div64 SYSCLK divided by 64 12 Div128 SYSCLK divided by 128 13 Div256 SYSCLK divided by 256 14 Div512 SYSCLK divided by 512 15 Div1 SYSCLK not divided true SWS System clock switch status 2 2 SWSR read HSI HSI oscillator used as system clock 0 HSE HSE oscillator used as system clock 1 PLL PLL used as system clock 2 SW System clock switch 0 2 SW HSI HSI selected as system clock 0 HSE HSE selected as system clock 1 PLL PLL selected as system clock 2 CIR CIR clock interrupt register 0xC 0x20 0x00000000 CSSC Clock security system interrupt clear 23 1 write-only CSSCW Clear Clear CSSF flag 1 LSIRDYC LSI ready interrupt clear 16 1 write-only LSIRDYCW Clear Clear interrupt flag 1 PLLSAIRDYC PLLSAI Ready Interrupt Clear 22 1 write-only PLLI2SRDYC PLLI2S ready interrupt clear 21 1 write-only PLLRDYC Main PLL(PLL) ready interrupt clear 20 1 write-only HSERDYC HSE ready interrupt clear 19 1 write-only HSIRDYC HSI ready interrupt clear 18 1 write-only LSERDYC LSE ready interrupt clear 17 1 write-only LSIRDYIE LSI ready interrupt enable 8 1 read-write LSIRDYIE Disabled Interrupt disabled 0 Enabled Interrupt enabled 1 PLLSAIRDYIE PLLSAI Ready Interrupt Enable 14 1 read-write PLLI2SRDYIE PLLI2S ready interrupt enable 13 1 read-write PLLRDYIE Main PLL (PLL) ready interrupt enable 12 1 read-write HSERDYIE HSE ready interrupt enable 11 1 read-write HSIRDYIE HSI ready interrupt enable 10 1 read-write LSERDYIE LSE ready interrupt enable 9 1 read-write CSSF Clock security system interrupt flag 7 1 read-only CSSFR NotInterrupted No clock security interrupt caused by HSE clock failure 0 Interrupted Clock security interrupt caused by HSE clock failure 1 LSIRDYF LSI ready interrupt flag 0 1 read-only LSIRDYFR NotInterrupted No clock ready interrupt 0 Interrupted Clock ready interrupt 1 PLLSAIRDYF PLLSAI ready interrupt flag 6 1 read-only PLLI2SRDYF PLLI2S ready interrupt flag 5 1 read-only PLLRDYF Main PLL (PLL) ready interrupt flag 4 1 read-only HSERDYF HSE ready interrupt flag 3 1 read-only HSIRDYF HSI ready interrupt flag 2 1 read-only LSERDYF LSE ready interrupt flag 1 1 read-only AHB1RSTR AHB1RSTR AHB1 peripheral reset register 0x10 0x20 read-write 0x00000000 GPIOARST IO port A reset 0 1 GPIOARST Reset Reset the selected module 1 OTGHSRST USB OTG HS module reset 29 1 ETHMACRST Ethernet MAC reset 25 1 DMA2DRST DMA2D reset 23 1 DMA2RST DMA2 reset 22 1 DMA1RST DMA2 reset 21 1 CRCRST CRC reset 12 1 GPIOKRST IO port K reset 10 1 GPIOJRST IO port J reset 9 1 GPIOIRST IO port I reset 8 1 GPIOHRST IO port H reset 7 1 GPIOGRST IO port G reset 6 1 GPIOFRST IO port F reset 5 1 GPIOERST IO port E reset 4 1 GPIODRST IO port D reset 3 1 GPIOCRST IO port C reset 2 1 GPIOBRST IO port B reset 1 1 AHB2RSTR AHB2RSTR AHB2 peripheral reset register 0x14 0x20 read-write 0x00000000 DCMIRST Camera interface reset 0 1 DCMIRST Reset Reset the selected module 1 OTGFSRST USB OTG FS module reset 7 1 RNGRST Random number generator module reset 6 1 HSAHRST Hash module reset 5 1 CRYPRST Cryptographic module reset 4 1 AHB3RSTR AHB3RSTR AHB3 peripheral reset register 0x18 0x20 read-write 0x00000000 FMCRST Flexible memory controller module reset 0 1 FMCRST Reset Reset the selected module 1 QSPIRST Quad SPI memory controller reset 1 1 APB1RSTR APB1RSTR APB1 peripheral reset register 0x20 0x20 read-write 0x00000000 TIM2RST TIM2 reset 0 1 TIM2RST Reset Reset the selected module 1 TIM3RST TIM3 reset 1 1 TIM4RST TIM4 reset 2 1 TIM5RST TIM5 reset 3 1 TIM6RST TIM6 reset 4 1 TIM7RST TIM7 reset 5 1 TIM12RST TIM12 reset 6 1 TIM13RST TIM13 reset 7 1 TIM14RST TIM14 reset 8 1 WWDGRST Window watchdog reset 11 1 SPI2RST SPI 2 reset 14 1 SPI3RST SPI 3 reset 15 1 USART2RST USART 2 reset 17 1 USART3RST USART 3 reset 18 1 UART4RST USART 4 reset 19 1 UART5RST USART 5 reset 20 1 I2C1RST I2C 1 reset 21 1 I2C2RST I2C 2 reset 22 1 I2C3RST I2C3 reset 23 1 CAN1RST CAN1 reset 25 1 CAN2RST CAN2 reset 26 1 PWRRST Power interface reset 28 1 DACRST DAC reset 29 1 UART7RST UART7 reset 30 1 UART8RST UART8 reset 31 1 SPDIFRXRST SPDIF-RX reset 16 1 CECRST HDMI-CEC reset 27 1 LPTIM1RST Low power timer 1 reset 9 1 I2C4RST I2C 4 reset 24 1 APB2RSTR APB2RSTR APB2 peripheral reset register 0x24 0x20 read-write 0x00000000 TIM1RST TIM1 reset 0 1 TIM1RST Reset Reset the selected module 1 TIM8RST TIM8 reset 1 1 USART1RST USART1 reset 4 1 USART6RST USART6 reset 5 1 ADCRST ADC interface reset (common to all ADCs) 8 1 SPI1RST SPI 1 reset 12 1 SPI4RST SPI4 reset 13 1 SYSCFGRST System configuration controller reset 14 1 TIM9RST TIM9 reset 16 1 TIM10RST TIM10 reset 17 1 TIM11RST TIM11 reset 18 1 SPI5RST SPI5 reset 20 1 SPI6RST SPI6 reset 21 1 SAI1RST SAI1 reset 22 1 LTDCRST LTDC reset 26 1 SAI2RST SAI2 reset 23 1 SDMMC1RST SDMMC1 reset 11 1 AHB1ENR AHB1ENR AHB1 peripheral clock register 0x30 0x20 read-write 0x00100000 GPIOAEN IO port A clock enable 0 1 GPIOAEN Disabled The selected clock is disabled 0 Enabled The selected clock is enabled 1 OTGHSULPIEN USB OTG HSULPI clock enable 30 1 OTGHSEN USB OTG HS clock enable 29 1 ETHMACPTPEN Ethernet PTP clock enable 28 1 ETHMACRXEN Ethernet Reception clock enable 27 1 ETHMACTXEN Ethernet Transmission clock enable 26 1 ETHMACEN Ethernet MAC clock enable 25 1 DMA2DEN DMA2D clock enable 23 1 DMA2EN DMA2 clock enable 22 1 DMA1EN DMA1 clock enable 21 1 DTCMRAMEN CCM data RAM clock enable 20 1 BKPSRAMEN Backup SRAM interface clock enable 18 1 CRCEN CRC clock enable 12 1 GPIOKEN IO port K clock enable 10 1 GPIOJEN IO port J clock enable 9 1 GPIOIEN IO port I clock enable 8 1 GPIOHEN IO port H clock enable 7 1 GPIOGEN IO port G clock enable 6 1 GPIOFEN IO port F clock enable 5 1 GPIOEEN IO port E clock enable 4 1 GPIODEN IO port D clock enable 3 1 GPIOCEN IO port C clock enable 2 1 GPIOBEN IO port B clock enable 1 1 AHB2ENR AHB2ENR AHB2 peripheral clock enable register 0x34 0x20 read-write 0x00000000 DCMIEN Camera interface enable 0 1 DCMIEN Disabled The selected clock is disabled 0 Enabled The selected clock is enabled 1 OTGFSEN USB OTG FS clock enable 7 1 RNGEN Random number generator clock enable 6 1 HASHEN Hash modules clock enable 5 1 CRYPEN Cryptographic modules clock enable 4 1 AHB3ENR AHB3ENR AHB3 peripheral clock enable register 0x38 0x20 read-write 0x00000000 FMCEN Flexible memory controller module clock enable 0 1 FMCEN Disabled The selected clock is disabled 0 Enabled The selected clock is enabled 1 QSPIEN Quad SPI memory controller clock enable 1 1 APB1ENR APB1ENR APB1 peripheral clock enable register 0x40 0x20 read-write 0x00000000 TIM2EN TIM2 clock enable 0 1 TIM2EN Disabled The selected clock is disabled 0 Enabled The selected clock is enabled 1 TIM3EN TIM3 clock enable 1 1 TIM4EN TIM4 clock enable 2 1 TIM5EN TIM5 clock enable 3 1 TIM6EN TIM6 clock enable 4 1 TIM7EN TIM7 clock enable 5 1 TIM12EN TIM12 clock enable 6 1 TIM13EN TIM13 clock enable 7 1 TIM14EN TIM14 clock enable 8 1 WWDGEN Window watchdog clock enable 11 1 SPI2EN SPI2 clock enable 14 1 SPI3EN SPI3 clock enable 15 1 USART2EN USART 2 clock enable 17 1 USART3EN USART3 clock enable 18 1 UART4EN UART4 clock enable 19 1 UART5EN UART5 clock enable 20 1 I2C1EN I2C1 clock enable 21 1 I2C2EN I2C2 clock enable 22 1 I2C3EN I2C3 clock enable 23 1 CAN1EN CAN 1 clock enable 25 1 CAN2EN CAN 2 clock enable 26 1 PWREN Power interface clock enable 28 1 DACEN DAC interface clock enable 29 1 UART7EN UART7 clock enable 30 1 UART8EN UART8 clock enable 31 1 SPDIFRXEN SPDIF-RX clock enable 16 1 CECEN HDMI-CEN clock enable 27 1 LPTIM1EN Low power timer 1 clock enable 9 1 I2C4EN I2C4 clock enable 24 1 APB2ENR APB2ENR APB2 peripheral clock enable register 0x44 0x20 read-write 0x00000000 TIM1EN TIM1 clock enable 0 1 TIM1EN Disabled The selected clock is disabled 0 Enabled The selected clock is enabled 1 TIM8EN TIM8 clock enable 1 1 USART1EN USART1 clock enable 4 1 USART6EN USART6 clock enable 5 1 ADC1EN ADC1 clock enable 8 1 ADC2EN ADC2 clock enable 9 1 ADC3EN ADC3 clock enable 10 1 SPI1EN SPI1 clock enable 12 1 SPI4EN SPI4 clock enable 13 1 SYSCFGEN System configuration controller clock enable 14 1 TIM9EN TIM9 clock enable 16 1 TIM10EN TIM10 clock enable 17 1 TIM11EN TIM11 clock enable 18 1 SPI5EN SPI5 clock enable 20 1 SPI6EN SPI6 clock enable 21 1 SAI1EN SAI1 clock enable 22 1 LTDCEN LTDC clock enable 26 1 SAI2EN SAI2 clock enable 23 1 SDMMC1EN SDMMC1 clock enable 11 1 AHB1LPENR AHB1LPENR AHB1 peripheral clock enable in low power mode register 0x50 0x20 read-write 0x7E6791FF GPIOALPEN IO port A clock enable during sleep mode 0 1 GPIOALPEN DisabledInSleep Selected module is disabled during Sleep mode 0 EnabledInSleep Selected module is enabled during Sleep mode 1 GPIOBLPEN IO port B clock enable during Sleep mode 1 1 GPIOCLPEN IO port C clock enable during Sleep mode 2 1 GPIODLPEN IO port D clock enable during Sleep mode 3 1 GPIOELPEN IO port E clock enable during Sleep mode 4 1 GPIOFLPEN IO port F clock enable during Sleep mode 5 1 GPIOGLPEN IO port G clock enable during Sleep mode 6 1 GPIOHLPEN IO port H clock enable during Sleep mode 7 1 GPIOILPEN IO port I clock enable during Sleep mode 8 1 GPIOJLPEN IO port J clock enable during Sleep mode 9 1 GPIOKLPEN IO port K clock enable during Sleep mode 10 1 CRCLPEN CRC clock enable during Sleep mode 12 1 FLITFLPEN Flash interface clock enable during Sleep mode 15 1 SRAM1LPEN SRAM 1interface clock enable during Sleep mode 16 1 SRAM2LPEN SRAM 2 interface clock enable during Sleep mode 17 1 BKPSRAMLPEN Backup SRAM interface clock enable during Sleep mode 18 1 SRAM3LPEN SRAM 3 interface clock enable during Sleep mode 19 1 DMA1LPEN DMA1 clock enable during Sleep mode 21 1 DMA2LPEN DMA2 clock enable during Sleep mode 22 1 DMA2DLPEN DMA2D clock enable during Sleep mode 23 1 ETHMACLPEN Ethernet MAC clock enable during Sleep mode 25 1 ETHMACTXLPEN Ethernet transmission clock enable during Sleep mode 26 1 ETHMACRXLPEN Ethernet reception clock enable during Sleep mode 27 1 ETHMACPTPLPEN Ethernet PTP clock enable during Sleep mode 28 1 OTGHSLPEN USB OTG HS clock enable during Sleep mode 29 1 OTGHSULPILPEN USB OTG HS ULPI clock enable during Sleep mode 30 1 AXILPEN AXI to AHB bridge clock enable during Sleep mode 13 1 DTCMLPEN DTCM RAM interface clock enable during Sleep mode 20 1 AHB2LPENR AHB2LPENR AHB2 peripheral clock enable in low power mode register 0x54 0x20 read-write 0x000000F1 DCMILPEN Camera interface enable during Sleep mode 0 1 DCMILPEN DisabledInSleep Selected module is disabled during Sleep mode 0 EnabledInSleep Selected module is enabled during Sleep mode 1 OTGFSLPEN USB OTG FS clock enable during Sleep mode 7 1 RNGLPEN Random number generator clock enable during Sleep mode 6 1 HASHLPEN Hash modules clock enable during Sleep mode 5 1 CRYPLPEN Cryptography modules clock enable during Sleep mode 4 1 AHB3LPENR AHB3LPENR AHB3 peripheral clock enable in low power mode register 0x58 0x20 read-write 0x00000001 FMCLPEN Flexible memory controller module clock enable during Sleep mode 0 1 FMCLPEN DisabledInSleep Selected module is disabled during Sleep mode 0 EnabledInSleep Selected module is enabled during Sleep mode 1 QSPILPEN Quand SPI memory controller clock enable during Sleep mode 1 1 APB1LPENR APB1LPENR APB1 peripheral clock enable in low power mode register 0x60 0x20 read-write 0x36FEC9FF TIM2LPEN TIM2 clock enable during Sleep mode 0 1 TIM2LPEN DisabledInSleep Selected module is disabled during Sleep mode 0 EnabledInSleep Selected module is enabled during Sleep mode 1 TIM3LPEN TIM3 clock enable during Sleep mode 1 1 TIM4LPEN TIM4 clock enable during Sleep mode 2 1 TIM5LPEN TIM5 clock enable during Sleep mode 3 1 TIM6LPEN TIM6 clock enable during Sleep mode 4 1 TIM7LPEN TIM7 clock enable during Sleep mode 5 1 TIM12LPEN TIM12 clock enable during Sleep mode 6 1 TIM13LPEN TIM13 clock enable during Sleep mode 7 1 TIM14LPEN TIM14 clock enable during Sleep mode 8 1 WWDGLPEN Window watchdog clock enable during Sleep mode 11 1 SPI2LPEN SPI2 clock enable during Sleep mode 14 1 SPI3LPEN SPI3 clock enable during Sleep mode 15 1 USART2LPEN USART2 clock enable during Sleep mode 17 1 USART3LPEN USART3 clock enable during Sleep mode 18 1 UART4LPEN UART4 clock enable during Sleep mode 19 1 UART5LPEN UART5 clock enable during Sleep mode 20 1 I2C1LPEN I2C1 clock enable during Sleep mode 21 1 I2C2LPEN I2C2 clock enable during Sleep mode 22 1 I2C3LPEN I2C3 clock enable during Sleep mode 23 1 CAN1LPEN CAN 1 clock enable during Sleep mode 25 1 CAN2LPEN CAN 2 clock enable during Sleep mode 26 1 PWRLPEN Power interface clock enable during Sleep mode 28 1 DACLPEN DAC interface clock enable during Sleep mode 29 1 UART7LPEN UART7 clock enable during Sleep mode 30 1 UART8LPEN UART8 clock enable during Sleep mode 31 1 SPDIFRXLPEN SPDIF-RX clock enable during sleep mode 16 1 CECLPEN HDMI-CEN clock enable during Sleep mode 27 1 LPTIM1LPEN low power timer 1 clock enable during Sleep mode 9 1 I2C4LPEN I2C4 clock enable during Sleep mode 24 1 APB2LPENR APB2LPENR APB2 peripheral clock enabled in low power mode register 0x64 0x20 read-write 0x00075F33 TIM1LPEN TIM1 clock enable during Sleep mode 0 1 TIM1LPEN DisabledInSleep Selected module is disabled during Sleep mode 0 EnabledInSleep Selected module is enabled during Sleep mode 1 TIM8LPEN TIM8 clock enable during Sleep mode 1 1 USART1LPEN USART1 clock enable during Sleep mode 4 1 USART6LPEN USART6 clock enable during Sleep mode 5 1 ADC1LPEN ADC1 clock enable during Sleep mode 8 1 ADC2LPEN ADC2 clock enable during Sleep mode 9 1 ADC3LPEN ADC 3 clock enable during Sleep mode 10 1 SPI1LPEN SPI 1 clock enable during Sleep mode 12 1 SPI4LPEN SPI 4 clock enable during Sleep mode 13 1 SYSCFGLPEN System configuration controller clock enable during Sleep mode 14 1 TIM9LPEN TIM9 clock enable during sleep mode 16 1 TIM10LPEN TIM10 clock enable during Sleep mode 17 1 TIM11LPEN TIM11 clock enable during Sleep mode 18 1 SPI5LPEN SPI 5 clock enable during Sleep mode 20 1 SPI6LPEN SPI 6 clock enable during Sleep mode 21 1 SAI1LPEN SAI1 clock enable during sleep mode 22 1 LTDCLPEN LTDC clock enable during sleep mode 26 1 SAI2LPEN SAI2 clock enable during sleep mode 23 1 SDMMC1LPEN SDMMC1 clock enable during Sleep mode 11 1 BDCR BDCR Backup domain control register 0x70 0x20 0x00000000 BDRST Backup domain software reset 16 1 read-write BDRST Disabled Reset not activated 0 Enabled Reset the entire RTC domain 1 RTCEN RTC clock enable 15 1 read-write RTCEN Disabled RTC clock disabled 0 Enabled RTC clock enabled 1 RTCSEL RTC clock source selection 8 2 RTCSEL NoClock No clock 0 LSE LSE oscillator clock used as RTC clock 1 LSI LSI oscillator clock used as RTC clock 2 HSE HSE oscillator clock divided by a prescaler used as RTC clock 3 LSEBYP External low-speed oscillator bypass 2 1 read-write LSEBYP NotBypassed LSE crystal oscillator not bypassed 0 Bypassed LSE crystal oscillator bypassed with external clock 1 LSERDY External low-speed oscillator ready 1 1 read-only LSERDYR NotReady LSE oscillator not ready 0 Ready LSE oscillator ready 1 LSEON External low-speed oscillator enable 0 1 read-write LSEON Off LSE oscillator Off 0 On LSE oscillator On 1 LSEDRV LSE oscillator drive capability 3 2 read-write LSEDRV Low Low drive capacity 0 MediumHigh Medium-high drive capacity 1 MediumLow Medium-low drive capacity 2 High High drive capacity 3 CSR CSR clock control & status register 0x74 0x20 0x0E000000 BORRSTF BOR reset flag 25 1 read-write BORRSTFR read NoReset No reset has occured 0 Reset A reset has occured 1 LPWRRSTF Low-power reset flag 31 1 read-write WWDGRSTF Window watchdog reset flag 30 1 read-write WDGRSTF Independent watchdog reset flag 29 1 read-write SFTRSTF Software reset flag 28 1 read-write PORRSTF POR/PDR reset flag 27 1 read-write PADRSTF PIN reset flag 26 1 read-write RMVF Remove reset flag 24 1 read-write RMVFW write Clear Clears the reset flag 1 LSIRDY Internal low-speed oscillator ready 1 1 read-only LSIRDYR NotReady LSI oscillator not ready 0 Ready LSI oscillator ready 1 LSION Internal low-speed oscillator enable 0 1 read-write LSION Off LSI oscillator Off 0 On LSI oscillator On 1 SSCGR SSCGR spread spectrum clock generation register 0x80 0x20 read-write 0x00000000 SSCGEN Spread spectrum modulation enable 31 1 SSCGEN Disabled Spread spectrum modulation disabled 0 Enabled Spread spectrum modulation enabled 1 SPREADSEL Spread Select 30 1 SPREADSEL Center Center spread 0 Down Down spread 1 INCSTEP Incrementation step 13 15 0 32767 MODPER Modulation period 0 13 0 8191 PLLI2SCFGR PLLI2SCFGR PLLI2S configuration register 0x84 0x20 read-write 0x20003000 PLLI2SR PLLI2S division factor for I2S clocks 28 3 2 7 PLLI2SQ PLLI2S division factor for SAI1 clock 24 4 2 15 PLLI2SN PLLI2S multiplication factor for VCO 6 9 50 432 PLLI2SP PLLI2S division factor for SPDIFRX clock 16 2 PLLSAICFGR PLLSAICFGR PLL configuration register 0x88 0x20 read-write 0x20003000 PLLSAIN PLLSAI division factor for VCO 6 9 50 432 PLLSAIP PLLSAI division factor for 48MHz clock 16 2 PLLSAIP Div2 PLL*P=2 0 Div4 PLL*P=4 1 Div6 PLL*P=6 2 Div8 PLL*P=8 3 PLLSAIQ PLLSAI division factor for SAI clock 24 4 2 15 PLLSAIR PLLSAI division factor for LCD clock 28 3 2 7 DCKCFGR1 DKCFGR1 dedicated clocks configuration register 0x8C 0x20 read-write 0x00000000 PLLI2SDIVQ PLLI2S division factor for SAI1 clock 0 5 PLLI2SDIVQ Div1 PLLI2SDIVQ = /1 0 Div2 PLLI2SDIVQ = /2 1 Div3 PLLI2SDIVQ = /3 2 Div4 PLLI2SDIVQ = /4 3 Div5 PLLI2SDIVQ = /5 4 Div6 PLLI2SDIVQ = /6 5 Div7 PLLI2SDIVQ = /7 6 Div8 PLLI2SDIVQ = /8 7 Div9 PLLI2SDIVQ = /9 8 Div10 PLLI2SDIVQ = /10 9 Div11 PLLI2SDIVQ = /11 10 Div12 PLLI2SDIVQ = /12 11 Div13 PLLI2SDIVQ = /13 12 Div14 PLLI2SDIVQ = /14 13 Div15 PLLI2SDIVQ = /15 14 Div16 PLLI2SDIVQ = /16 15 Div17 PLLI2SDIVQ = /17 16 Div18 PLLI2SDIVQ = /18 17 Div19 PLLI2SDIVQ = /19 18 Div20 PLLI2SDIVQ = /20 19 Div21 PLLI2SDIVQ = /21 20 Div22 PLLI2SDIVQ = /22 21 Div23 PLLI2SDIVQ = /23 22 Div24 PLLI2SDIVQ = /24 23 Div25 PLLI2SDIVQ = /25 24 Div26 PLLI2SDIVQ = /26 25 Div27 PLLI2SDIVQ = /27 26 Div28 PLLI2SDIVQ = /28 27 Div29 PLLI2SDIVQ = /29 28 Div30 PLLI2SDIVQ = /30 29 Div31 PLLI2SDIVQ = /31 30 Div32 PLLI2SDIVQ = /32 31 PLLSAIDIVQ PLLSAI division factor for SAI1 clock 8 5 PLLSAIDIVQ Div1 PLLSAIDIVQ = /1 0 Div2 PLLSAIDIVQ = /2 1 Div3 PLLSAIDIVQ = /3 2 Div4 PLLSAIDIVQ = /4 3 Div5 PLLSAIDIVQ = /5 4 Div6 PLLSAIDIVQ = /6 5 Div7 PLLSAIDIVQ = /7 6 Div8 PLLSAIDIVQ = /8 7 Div9 PLLSAIDIVQ = /9 8 Div10 PLLSAIDIVQ = /10 9 Div11 PLLSAIDIVQ = /11 10 Div12 PLLSAIDIVQ = /12 11 Div13 PLLSAIDIVQ = /13 12 Div14 PLLSAIDIVQ = /14 13 Div15 PLLSAIDIVQ = /15 14 Div16 PLLSAIDIVQ = /16 15 Div17 PLLSAIDIVQ = /17 16 Div18 PLLSAIDIVQ = /18 17 Div19 PLLSAIDIVQ = /19 18 Div20 PLLSAIDIVQ = /20 19 Div21 PLLSAIDIVQ = /21 20 Div22 PLLSAIDIVQ = /22 21 Div23 PLLSAIDIVQ = /23 22 Div24 PLLSAIDIVQ = /24 23 Div25 PLLSAIDIVQ = /25 24 Div26 PLLSAIDIVQ = /26 25 Div27 PLLSAIDIVQ = /27 26 Div28 PLLSAIDIVQ = /28 27 Div29 PLLSAIDIVQ = /29 28 Div30 PLLSAIDIVQ = /30 29 Div31 PLLSAIDIVQ = /31 30 Div32 PLLSAIDIVQ = /32 31 PLLSAIDIVR division factor for LCD_CLK 16 2 PLLSAIDIVR Div2 PLLSAIDIVR = /2 0 Div4 PLLSAIDIVR = /4 1 Div8 PLLSAIDIVR = /8 2 Div16 PLLSAIDIVR = /16 3 SAI1SEL SAI1 clock source selection 20 2 SAI1SEL PLLSAI SAI1 clock frequency = f(PLLSAI_Q) / PLLSAIDIVQ 0 PLLI2S SAI1 clock frequency = f(PLLI2S_Q) / PLLI2SDIVQ 1 AFIF SAI1 clock frequency = Alternate function input frequency 2 HSI_HSE SAI1 clock frequency = HSI or HSE 3 SAI2SEL SAI2 clock source selection 22 2 SAI2SEL PLLSAI SAI2 clock frequency = f(PLLSAI_Q) / PLLSAIDIVQ 0 PLLI2S SAI2 clock frequency = f(PLLI2S_Q) / PLLI2SDIVQ 1 AFIF SAI2 clock frequency = Alternate function input frequency 2 HSI_HSE SAI2 clock frequency = HSI or HSE 3 TIMPRE Timers clocks prescalers selection 24 1 TIMPRE Mul1Or2 If the APB prescaler is configured 1, TIMxCLK = PCLKx. Otherwise, TIMxCLK = 2xPCLKx 0 Mul1Or4 If the APB prescaler is configured 1, 2 or 4, TIMxCLK = HCLK. Otherwise, TIMxCLK = 4xPCLKx 1 DCKCFGR2 DKCFGR2 dedicated clocks configuration register 0x90 0x20 read-write 0x00000000 USART1SEL USART 1 clock source selection 0 2 USART1SEL APB2 APB2 clock (PCLK2) is selected as USART clock 0 SYSCLK System clock is selected as USART clock 1 HSI HSI clock is selected as USART clock 2 LSE LSE clock is selected as USART clock 3 USART2SEL USART 2 clock source selection 2 2 USART2SEL APB1 APB1 clock (PCLK1) is selected as USART clock 0 SYSCLK System clock is selected as USART clock 1 HSI HSI clock is selected as USART clock 2 LSE LSE clock is selected as USART clock 3 USART3SEL USART 3 clock source selection 4 2 UART4SEL UART 4 clock source selection 6 2 UART5SEL UART 5 clock source selection 8 2 USART6SEL USART 6 clock source selection 10 2 UART7SEL UART 7 clock source selection 12 2 UART8SEL UART 8 clock source selection 14 2 I2C1SEL I2C1 clock source selection 16 2 I2C1SEL APB APB clock selected as I2C clock 0 SYSCLK System clock selected as I2C clock 1 HSI HSI clock selected as I2C clock 2 I2C2SEL I2C2 clock source selection 18 2 I2C3SEL I2C3 clock source selection 20 2 I2C4SEL I2C4 clock source selection 22 2 LPTIM1SEL Low power timer 1 clock source selection 24 2 LPTIM1SEL APB1 APB1 clock (PCLK1) selected as LPTILM1 clock 0 LSI LSI clock is selected as LPTILM1 clock 1 HSI HSI clock is selected as LPTILM1 clock 2 LSE LSE clock is selected as LPTILM1 clock 3 CECSEL HDMI-CEC clock source selection 26 1 CECSEL LSE LSE clock is selected as HDMI-CEC clock 0 HSI_Div488 HSI divided by 488 clock is selected as HDMI-CEC clock 1 CK48MSEL 48MHz clock source selection 27 1 CK48MSEL PLL 48MHz clock from PLL is selected 0 PLLSAI 48MHz clock from PLLSAI is selected 1 SDMMC1SEL SDMMC clock source selection 28 1 SDMMC1SEL CK48M 48 MHz clock is selected as SD clock 0 SYSCLK System clock is selected as SD clock 1 GPIOD General-purpose I/Os GPIO 0x40020C00 0x0 0x400 registers MODER MODER GPIO port mode register 0x0 0x20 read-write 0x00000000 16 0x2 0-15 MODER%s Port x configuration pin %s 0 2 OTYPER OTYPER GPIO port output type register 0x4 OSPEEDR OSPEEDR GPIO port output speed register 0x8 0x20 read-write 0x00000000 16 0x2 0-15 OSPEEDR%s Port x configuration pin %s 0 2 PUPDR PUPDR GPIO port pull-up/pull-down register 0xC 0x20 read-write 0x00000000 16 0x2 0-15 PUPDR%s Port x configuration pin %s 0 2 IDR IDR GPIO port input data register 0x10 ODR ODR GPIO port output data register 0x14 BSRR BSRR GPIO port bit set/reset register 0x18 LCKR LCKR GPIO port configuration lock register 0x1C AFRL AFRL GPIO alternate function lowregister 0x20 AFRH AFRH GPIO alternate function high register 0x24 BRR BRR GPIO port bit reset register 0x28 GPIOC 0x40020800 GPIOK 0x40022800 GPIOJ 0x40022400 GPIOI 0x40022000 GPIOH 0x40021C00 GPIOG 0x40021800 GPIOF 0x40021400 GPIOE 0x40021000 GPIOB General-purpose I/Os GPIO 0x40020400 0x0 0x400 registers MODER MODER GPIO port mode register 0x0 0x20 read-write 0x00000280 16 0x2 0-15 MODER%s Port x configuration pin %s 0 2 OTYPER OTYPER GPIO port output type register 0x4 OSPEEDR OSPEEDR GPIO port output speed register 0x8 0x20 read-write 0x000000C0 16 0x2 0-15 OSPEEDR%s Port x configuration pin %s 0 2 PUPDR PUPDR GPIO port pull-up/pull-down register 0xC 0x20 read-write 0x00000100 16 0x2 0-15 PUPDR%s Port x configuration pin %s 0 2 IDR IDR GPIO port input data register 0x10 ODR ODR GPIO port output data register 0x14 BSRR BSRR GPIO port bit set/reset register 0x18 LCKR LCKR GPIO port configuration lock register 0x1C AFRL AFRL GPIO alternate function low register 0x20 AFRH AFRH GPIO alternate function high register 0x24 BRR BRR GPIO port bit reset register 0x28 GPIOA General-purpose I/Os GPIO 0x40020000 0x0 0x400 registers MODER MODER GPIO port mode register 0x0 0x20 read-write 0xA8000000 16 0x2 0-15 MODER%s Port x configuration pin %s 0 2 Mode Input Input mode (reset state) 0 Output General purpose output mode 1 Alternate Alternate function mode 2 Analog Analog mode 3 OTYPER OTYPER GPIO port output type register 0x4 0x20 read-write 0x00000000 16 0x1 0-15 OT%s Port x configuration pin %s 0 1 OutputType PushPull Output push-pull (reset state) 0 OpenDrain Output open-drain 1 OSPEEDR OSPEEDR GPIO port output speed register 0x8 0x20 read-write 0x00000000 16 0x2 0-15 OSPEEDR%s Port x configuration pin %s 0 2 OutputSpeed LowSpeed Low speed 0 MediumSpeed Medium speed 1 HighSpeed High speed 2 VeryHighSpeed Very high speed 3 PUPDR PUPDR GPIO port pull-up/pull-down register 0xC 0x20 read-write 0x64000000 16 0x2 0-15 PUPDR%s Port x configuration pin %s 0 2 Pull Floating No pull-up, pull-down 0 PullUp Pull-up 1 PullDown Pull-down 2 IDR IDR GPIO port input data register 0x10 0x20 read-only 0x00000000 16 0x1 0-15 IDR%s Port input data pin %s 0 1 InputData Low Input is logic low 0 High Input is logic high 1 ODR ODR GPIO port output data register 0x14 0x20 read-write 0x00000000 16 0x1 0-15 ODR%s Port output data pin %s 0 1 OutputData Low Set output to logic low 0 High Set output to logic high 1 BSRR BSRR GPIO port bit set/reset register 0x18 0x20 write-only 0x00000000 16 0x1 0-15 BR%s Port x reset pin %s 16 1 BitReset Reset Resets the corresponding ODRx bit 1 16 0x1 0-15 BS%s Port x set pin %s 0 1 BitSet Set Sets the corresponding ODRx bit 1 LCKR LCKR GPIO port configuration lock register 0x1C 0x20 read-write 0x00000000 LCKK Port x lock bit y (y= 0..15) 16 1 LockKey NotActive Port configuration lock key not active 0 Active Port configuration lock key active 1 16 0x1 0-15 LCK%s Port x lock pin %s 0 1 Lock Unlocked Port configuration not locked 0 Locked Port configuration locked 1 AFRL AFRL GPIO alternate function low register 0x20 0x20 read-write 0x00000000 8 0x4 L0,L1,L2,L3,L4,L5,L6,L7 AFR%s Alternate function selection for port x bit y (y = 0..7) 0 4 AlternateFunction AF0 AF0 0 AF1 AF1 1 AF2 AF2 2 AF3 AF3 3 AF4 AF4 4 AF5 AF5 5 AF6 AF6 6 AF7 AF7 7 AF8 AF8 8 AF9 AF9 9 AF10 AF10 10 AF11 AF11 11 AF12 AF12 12 AF13 AF13 13 AF14 AF14 14 AF15 AF15 15 AFRH AFRH GPIO alternate function high register 0x24 0x20 read-write 0x00000000 8 0x4 H8,H9,H10,H11,H12,H13,H14,H15 AFR%s Alternate function selection for port x bit y (y = 8..15) 0 4 BRR BRR GPIO port bit reset register 0x28 0x20 read-write 0x00000000 16 0x1 0-15 BR%s Port x reset pin %s 0 1 BitReset write NoAction No action on the corresponding ODx bit 0 Reset Reset the ODx bit 1 SYSCFG System configuration controller SYSCFG 0x40013800 0x0 0x400 registers MEMRMP MEMRM memory remap register 0x0 0x20 read-write 0x00000000 MEM_BOOT Memory mapping selection 0 1 MEM_BOOT Add0 Boot memory base address is defined by FLASH.OPTCR1.BOOT_ADD0 0 Add1 Boot memory base address is defined by FLASH.OPTCR1.BOOT_ADD1 1 SWP_FMC FMC memory mapping swap 10 2 SWP_FMC NoSwap No FMC memory mapping swap 0 Swapped SDRAM banks and NOR/RAM mapping are swapped 1 PMC PMC peripheral mode configuration register 0x4 0x20 read-write 0x00000000 MII_RMII_SEL Ethernet PHY interface selection 23 1 MII_RMII_SEL MII MII interface is selected 0 RMII_PHY RMII PHY interface is selected 1 ADC1DC2 ADC1DC2 16 1 0 1 ADC2DC2 ADC2DC2 17 1 0 1 ADC3DC2 ADC3DC2 18 1 0 1 EXTICR1 EXTICR1 external interrupt configuration register 1 0x8 0x20 read-write 0x00000000 EXTI3 EXTI x configuration (x = 0 to 3) 12 4 EXTI2 EXTI x configuration (x = 0 to 3) 8 4 EXTI1 EXTI x configuration (x = 0 to 3) 4 4 EXTI0 EXTI x configuration (x = 0 to 3) 0 4 EXTI0 PA Select PAx as the source input for the EXTIx external interrupt 0 PB Select PBx as the source input for the EXTIx external interrupt 1 PC Select PCx as the source input for the EXTIx external interrupt 2 PD Select PDx as the source input for the EXTIx external interrupt 3 PE Select PEx as the source input for the EXTIx external interrupt 4 PF Select PFx as the source input for the EXTIx external interrupt 5 PG Select PGx as the source input for the EXTIx external interrupt 6 PH Select PHx as the source input for the EXTIx external interrupt 7 PI Select PIx as the source input for the EXTIx external interrupt 8 PJ Select PJx as the source input for the EXTIx external interrupt 9 PK Select PKx as the source input for the EXTIx external interrupt 10 EXTICR2 EXTICR2 external interrupt configuration register 2 0xC 0x20 read-write 0x00000000 EXTI7 EXTI x configuration (x = 4 to 7) 12 4 EXTI6 EXTI x configuration (x = 4 to 7) 8 4 EXTI5 EXTI x configuration (x = 4 to 7) 4 4 EXTI4 EXTI x configuration (x = 4 to 7) 0 4 EXTICR3 EXTICR3 external interrupt configuration register 3 0x10 0x20 read-write 0x00000000 EXTI11 EXTI x configuration (x = 8 to 11) 12 4 EXTI10 EXTI10 8 4 EXTI9 EXTI x configuration (x = 8 to 11) 4 4 EXTI8 EXTI x configuration (x = 8 to 11) 0 4 EXTICR4 EXTICR4 external interrupt configuration register 4 0x14 0x20 read-write 0x00000000 EXTI15 EXTI x configuration (x = 12 to 15) 12 4 EXTI14 EXTI x configuration (x = 12 to 15) 8 4 EXTI13 EXTI x configuration (x = 12 to 15) 4 4 EXTI12 EXTI x configuration (x = 12 to 15) 0 4 CMPCR CMPCR Compensation cell control register 0x20 0x20 read-only 0x00000000 READY READY 8 1 READY NotReady I/O compensation cell not ready 0 Ready I/O compensation cell ready 1 CMP_PD Compensation cell power-down 0 1 CMP_PD PowerDown I/O compensation cell power-down mode 0 Enabled I/O compensation cell enabled 1 SPI1 Serial peripheral interface SPI 0x40013000 0x0 0x400 registers SPI1 SPI1 global interrupt 35 CR1 CR1 control register 1 0x0 0x10 read-write 0x00000000 BIDIMODE Bidirectional data mode enable 15 1 BIDIMODE Unidirectional 2-line unidirectional data mode selected 0 Bidirectional 1-line bidirectional data mode selected 1 BIDIOE Output enable in bidirectional mode 14 1 BIDIOE OutputDisabled Output disabled (receive-only mode) 0 OutputEnabled Output enabled (transmit-only mode) 1 CRCEN Hardware CRC calculation enable 13 1 CRCEN Disabled CRC calculation disabled 0 Enabled CRC calculation enabled 1 CRCNEXT CRC transfer next 12 1 CRCNEXT TxBuffer Next transmit value is from Tx buffer 0 CRC Next transmit value is from Tx CRC register 1 CRCL CRC length 11 1 CRCL EightBit 8-bit CRC length 0 SixteenBit 16-bit CRC length 1 RXONLY Receive only 10 1 RXONLY FullDuplex Full duplex (Transmit and receive) 0 OutputDisabled Output disabled (Receive-only mode) 1 SSM Software slave management 9 1 SSM Disabled Software slave management disabled 0 Enabled Software slave management enabled 1 SSI Internal slave select 8 1 SSI SlaveSelected 0 is forced onto the NSS pin and the I/O value of the NSS pin is ignored 0 SlaveNotSelected 1 is forced onto the NSS pin and the I/O value of the NSS pin is ignored 1 LSBFIRST Frame format 7 1 LSBFIRST MSBFirst Data is transmitted/received with the MSB first 0 LSBFirst Data is transmitted/received with the LSB first 1 SPE SPI enable 6 1 SPE Disabled Peripheral disabled 0 Enabled Peripheral enabled 1 BR Baud rate control 3 3 BR Div2 f_PCLK / 2 0 Div4 f_PCLK / 4 1 Div8 f_PCLK / 8 2 Div16 f_PCLK / 16 3 Div32 f_PCLK / 32 4 Div64 f_PCLK / 64 5 Div128 f_PCLK / 128 6 Div256 f_PCLK / 256 7 MSTR Master selection 2 1 MSTR Slave Slave configuration 0 Master Master configuration 1 CPOL Clock polarity 1 1 CPOL IdleLow CK to 0 when idle 0 IdleHigh CK to 1 when idle 1 CPHA Clock phase 0 1 CPHA FirstEdge The first clock transition is the first data capture edge 0 SecondEdge The second clock transition is the first data capture edge 1 CR2 CR2 control register 2 0x4 0x10 read-write 0x00000700 RXDMAEN Rx buffer DMA enable 0 1 RXDMAEN Disabled Rx buffer DMA disabled 0 Enabled Rx buffer DMA enabled 1 TXDMAEN Tx buffer DMA enable 1 1 TXDMAEN Disabled Tx buffer DMA disabled 0 Enabled Tx buffer DMA enabled 1 SSOE SS output enable 2 1 SSOE Disabled SS output is disabled in master mode 0 Enabled SS output is enabled in master mode 1 NSSP NSS pulse management 3 1 NSSP NoPulse No NSS pulse 0 PulseGenerated NSS pulse generated 1 FRF Frame format 4 1 FRF Motorola SPI Motorola mode 0 TI SPI TI mode 1 ERRIE Error interrupt enable 5 1 ERRIE Masked Error interrupt masked 0 NotMasked Error interrupt not masked 1 RXNEIE RX buffer not empty interrupt enable 6 1 RXNEIE Masked RXE interrupt masked 0 NotMasked RXE interrupt not masked 1 TXEIE Tx buffer empty interrupt enable 7 1 TXEIE Masked TXE interrupt masked 0 NotMasked TXE interrupt not masked 1 DS Data size 8 4 DS FourBit 4-bit 3 FiveBit 5-bit 4 SixBit 6-bit 5 SevenBit 7-bit 6 EightBit 8-bit 7 NineBit 9-bit 8 TenBit 10-bit 9 ElevenBit 11-bit 10 TwelveBit 12-bit 11 ThirteenBit 13-bit 12 FourteenBit 14-bit 13 FifteenBit 15-bit 14 SixteenBit 16-bit 15 FRXTH FIFO reception threshold 12 1 FRXTH Half RXNE event is generated if the FIFO level is greater than or equal to 1/2 (16-bit) 0 Quarter RXNE event is generated if the FIFO level is greater than or equal to 1/4 (8-bit) 1 LDMA_RX Last DMA transfer for reception 13 1 LDMA_RX Even Number of data to transfer for receive is even 0 Odd Number of data to transfer for receive is odd 1 LDMA_TX Last DMA transfer for transmission 14 1 LDMA_TX Even Number of data to transfer for transmit is even 0 Odd Number of data to transfer for transmit is odd 1 SR SR status register 0x8 0x10 0x00000002 FRE Frame format error 8 1 read-only FRER NoError No frame format error 0 Error A frame format error occurred 1 BSY Busy flag 7 1 read-only BSYR NotBusy SPI not busy 0 Busy SPI busy 1 OVR Overrun flag 6 1 read-only OVRR NoOverrun No overrun occurred 0 Overrun Overrun occurred 1 MODF Mode fault 5 1 read-only MODFR NoFault No mode fault occurred 0 Fault Mode fault occurred 1 CRCERR CRC error flag 4 1 read-write zeroToClear CRCERRR read Match CRC value received matches the SPIx_RXCRCR value 0 NoMatch CRC value received does not match the SPIx_RXCRCR value 1 CRCERRW write Clear Clear flag 0 UDR Underrun flag 3 1 read-only UDRR NoUnderrun No underrun occurred 0 Underrun Underrun occurred 1 CHSIDE Channel side 2 1 read-only CHSIDE Left Channel left has to be transmitted or has been received 0 Right Channel right has to be transmitted or has been received 1 TXE Transmit buffer empty 1 1 read-only TXE NotEmpty Tx buffer not empty 0 Empty Tx buffer empty 1 RXNE Receive buffer not empty 0 1 read-only RXNE Empty Rx buffer empty 0 NotEmpty Rx buffer not empty 1 FRLVL FIFO reception level 9 2 read-only FRLVLR Empty Rx FIFO Empty 0 Quarter Rx 1/4 FIFO 1 Half Rx 1/2 FIFO 2 Full Rx FIFO full 3 FTLVL FIFO Transmission Level 11 2 read-only FTLVLR Empty Tx FIFO Empty 0 Quarter Tx 1/4 FIFO 1 Half Tx 1/2 FIFO 2 Full Tx FIFO full 3 DR DR data register 0xC 0x10 read-write 0x00000000 DR Data register 0 16 0 65535 DR8 Direct 8-bit access to data register DR 0xC 0x8 read-write DR Data register 0 8 0 255 CRCPR CRCPR CRC polynomial register 0x10 0x10 read-write 0x00000007 CRCPOLY CRC polynomial register 0 16 0 65535 RXCRCR RXCRCR RX CRC register 0x14 0x10 read-only 0x00000000 RxCRC Rx CRC register 0 16 0 65535 TXCRCR TXCRCR TX CRC register 0x18 0x10 read-only 0x00000000 TxCRC Tx CRC register 0 16 0 65535 I2SCFGR I2SCFGR I2S configuration register 0x1C 0x10 read-write 0x00000000 I2SMOD I2S mode selection 11 1 I2SMOD SPIMode SPI mode is selected 0 I2SMode I2S mode is selected 1 I2SE I2S Enable 10 1 I2SE Disabled I2S peripheral is disabled 0 Enabled I2S peripheral is enabled 1 I2SCFG I2S configuration mode 8 2 I2SCFG SlaveTx Slave - transmit 0 SlaveRx Slave - receive 1 MasterTx Master - transmit 2 MasterRx Master - receive 3 PCMSYNC PCM frame synchronization 7 1 PCMSYNC Short Short frame synchronisation 0 Long Long frame synchronisation 1 I2SSTD I2S standard selection 4 2 I2SSTD Philips I2S Philips standard 0 MSB MSB justified standard 1 LSB LSB justified standard 2 PCM PCM standard 3 CKPOL Steady state clock polarity 3 1 CKPOL IdleLow I2S clock inactive state is low level 0 IdleHigh I2S clock inactive state is high level 1 DATLEN Data length to be transferred 1 2 DATLEN SixteenBit 16-bit data length 0 TwentyFourBit 24-bit data length 1 ThirtyTwoBit 32-bit data length 2 CHLEN Channel length (number of bits per audio channel) 0 1 CHLEN SixteenBit 16-bit wide 0 ThirtyTwoBit 32-bit wide 1 ASTRTEN Asynchronous start enable 12 1 ASTRTEN AsyncStartDisabled Asynchronous start disabled 0 AsyncStartEnabled Asynchronous start enabled 1 I2SPR I2SPR I2S prescaler register 0x20 0x10 read-write 0x0000000A MCKOE Master clock output enable 9 1 MCKOE Disabled Master clock output is disabled 0 Enabled Master clock output is enabled 1 ODD Odd factor for the prescaler 8 1 ODD Even Real divider value is I2SDIV * 2 0 Odd Real divider value is (I2SDIV * 2) + 1 1 I2SDIV I2S Linear prescaler 0 8 2 255 SPI3 0x40003C00 SPI3 SPI3 global interrupt 51 SPI4 0x40013400 SPI4 SPI 4 global interrupt 84 SPI5 0x40015000 SPI5 SPI 5 global interrupt 85 SPI6 0x40015400 SPI6 SPI 6 global interrupt 86 SPI2 Serial peripheral interface SPI 0x40003800 SPI2 SPI2 global interrupt 36 ADC1 Analog-to-digital converter ADC 0x40012000 0x0 0x100 registers ADC ADC1 global interrupt 18 SR SR status register 0x0 0x20 read-write 0x00000000 OVR Overrun 5 1 zeroToClear OVRR read NoOverrun No overrun occurred 0 Overrun Overrun occurred 1 OVRW write Clear Clear flag 0 STRT Regular channel start flag 4 1 zeroToClear STRTR read NotStarted No regular channel conversion started 0 Started Regular channel conversion has started 1 STRTW write Clear Clear flag 0 JSTRT Injected channel start flag 3 1 zeroToClear JSTRTR read NotStarted No injected channel conversion started 0 Started Injected channel conversion has started 1 JSTRTW write Clear Clear flag 0 JEOC Injected channel end of conversion 2 1 zeroToClear JEOCR read NotComplete Conversion is not complete 0 Complete Conversion complete 1 JEOCW write Clear Clear flag 0 EOC Regular channel end of conversion 1 1 zeroToClear EOCR read NotComplete Conversion is not complete 0 Complete Conversion complete 1 EOCW write Clear Clear flag 0 AWD Analog watchdog flag 0 1 zeroToClear AWDR read NoEvent No analog watchdog event occurred 0 Event Analog watchdog event occurred 1 AWDW write Clear Clear flag 0 CR1 CR1 control register 1 0x4 0x20 read-write 0x00000000 OVRIE Overrun interrupt enable 26 1 OVRIE Disabled Overrun interrupt disabled 0 Enabled Overrun interrupt enabled 1 RES Resolution 24 2 RES TwelveBit 12-bit (15 ADCCLK cycles) 0 TenBit 10-bit (13 ADCCLK cycles) 1 EightBit 8-bit (11 ADCCLK cycles) 2 SixBit 6-bit (9 ADCCLK cycles) 3 AWDEN Analog watchdog enable on regular channels 23 1 AWDEN Disabled Analog watchdog disabled on regular channels 0 Enabled Analog watchdog enabled on regular channels 1 JAWDEN Analog watchdog enable on injected channels 22 1 JAWDEN Disabled Analog watchdog disabled on injected channels 0 Enabled Analog watchdog enabled on injected channels 1 DISCNUM Discontinuous mode channel count 13 3 0 7 JDISCEN Discontinuous mode on injected channels 12 1 JDISCEN Disabled Discontinuous mode on injected channels disabled 0 Enabled Discontinuous mode on injected channels enabled 1 DISCEN Discontinuous mode on regular channels 11 1 DISCEN Disabled Discontinuous mode on regular channels disabled 0 Enabled Discontinuous mode on regular channels enabled 1 JAUTO Automatic injected group conversion 10 1 JAUTO Disabled Automatic injected group conversion disabled 0 Enabled Automatic injected group conversion enabled 1 AWDSGL Enable the watchdog on a single channel in scan mode 9 1 AWDSGL AllChannels Analog watchdog enabled on all channels 0 SingleChannel Analog watchdog enabled on a single channel 1 SCAN Scan mode 8 1 SCAN Disabled Scan mode disabled 0 Enabled Scan mode enabled 1 JEOCIE Interrupt enable for injected channels 7 1 JEOCIE Disabled JEOC interrupt disabled 0 Enabled JEOC interrupt enabled 1 AWDIE Analog watchdog interrupt enable 6 1 AWDIE Disabled Analogue watchdog interrupt disabled 0 Enabled Analogue watchdog interrupt enabled 1 EOCIE Interrupt enable for EOC 5 1 EOCIE Disabled EOC interrupt disabled 0 Enabled EOC interrupt enabled 1 AWDCH Analog watchdog channel select bits 0 5 0 18 CR2 CR2 control register 2 0x8 0x20 read-write 0x00000000 SWSTART Start conversion of regular channels 30 1 SWSTARTW write Start Starts conversion of regular channels 1 EXTEN External trigger enable for regular channels 28 2 EXTEN Disabled Trigger detection disabled 0 RisingEdge Trigger detection on the rising edge 1 FallingEdge Trigger detection on the falling edge 2 BothEdges Trigger detection on both the rising and falling edges 3 EXTSEL External event select for regular group 24 4 EXTSEL TIM1CH1 Timer 1 CH1 0 TIM1CH2 Timer 1 CH2 1 TIM1CH3 Timer 1 CH3 2 TIM2CH2 Timer 2 CH2 3 TIM5TRGO Timer 5 TRGO 4 TIM4CH4 Timer 4 CH4 5 TIM3CH4 Timer 3 CH4 6 TIM8TRGO Timer 8 TRGO 7 TIM8TRGO2 Timer 8 TRGO(2) 8 TIM1TRGO Timer 1 TRGO 9 TIM1TRGO2 Timer 1 TRGO(2) 10 TIM2TRGO Timer 2 TRGO 11 TIM4TRGO Timer 4 TRGO 12 TIM6TRGO Timer 6 TRGO 13 EXTI11 EXTI line 11 15 JSWSTART Start conversion of injected channels 22 1 JSWSTARTW write Start Starts conversion of injected channels 1 JEXTEN External trigger enable for injected channels 20 2 JEXTEN Disabled Trigger detection disabled 0 RisingEdge Trigger detection on the rising edge 1 FallingEdge Trigger detection on the falling edge 2 BothEdges Trigger detection on both the rising and falling edges 3 JEXTSEL External event select for injected group 16 4 JEXTSEL TIM1TRGO Timer 1 TRGO 0 TIM1CH4 Timer 1 CH4 1 TIM2TRGO Timer 2 TRGO 2 TIM2CH1 Timer 2 CH1 3 TIM3CH4 Timer 3 CH4 4 TIM4TRGO Timer 4 TRGO 5 TIM8CH4 Timer 8 CH4 7 TIM1TRGO2 Timer 1 TRGO(2) 8 TIM8TRGO Timer 8 TRGO 9 TIM8TRGO2 Timer 8 TRGO(2) 10 TIM3CH3 Timer 3 CH3 11 TIM5TRGO Timer 5 TRGO 12 TIM3CH1 Timer 3 CH1 13 TIM6TRGO Timer 6 TRGO 14 ALIGN Data alignment 11 1 ALIGN Right Right alignment 0 Left Left alignment 1 EOCS End of conversion selection 10 1 EOCS EachSequence The EOC bit is set at the end of each sequence of regular conversions 0 EachConversion The EOC bit is set at the end of each regular conversion 1 DDS DMA disable selection (for single ADC mode) 9 1 DDS Single No new DMA request is issued after the last transfer 0 Continuous DMA requests are issued as long as data are converted and DMA=1 1 DMA Direct memory access mode (for single ADC mode) 8 1 DMA Disabled DMA mode disabled 0 Enabled DMA mode enabled 1 CONT Continuous conversion 1 1 CONT Single Single conversion mode 0 Continuous Continuous conversion mode 1 ADON A/D Converter ON / OFF 0 1 ADON Disabled Disable ADC conversion and go to power down mode 0 Enabled Enable ADC 1 SMPR1 SMPR1 sample time register 1 0xC 0x20 read-write 0x00000000 9 0x3 10-18 SMP%s Channel %s sample time selection 0 3 SMP10 Cycles3 3 cycles 0 Cycles15 15 cycles 1 Cycles28 28 cycles 2 Cycles56 56 cycles 3 Cycles84 84 cycles 4 Cycles112 112 cycles 5 Cycles144 144 cycles 6 Cycles480 480 cycles 7 SMPR2 SMPR2 sample time register 2 0x10 0x20 read-write 0x00000000 10 0x3 0-9 SMP%s Channel %s sample time selection 0 3 4 0x4 1-4 JOFR%s JOFR%s injected channel data offset register %s 0x14 0x20 read-write 0x00000000 JOFFSET Data offset for injected channel 0 12 0 4095 HTR HTR watchdog higher threshold register 0x24 0x20 read-write 0x00000FFF HT Analog watchdog higher threshold 0 12 0 4095 LTR LTR watchdog lower threshold register 0x28 0x20 read-write 0x00000000 LT Analog watchdog lower threshold 0 12 0 4095 SQR1 SQR1 regular sequence register 1 0x2C 0x20 read-write 0x00000000 L Regular channel sequence length 20 4 0 15 4 0x5 13-16 SQ%s %s conversion in regular sequence 0 5 0 18 SQR2 SQR2 regular sequence register 2 0x30 0x20 read-write 0x00000000 6 0x5 7-12 SQ%s %s conversion in regular sequence 0 5 SQR3 SQR3 regular sequence register 3 0x34 0x20 read-write 0x00000000 6 0x5 1-6 SQ%s %s conversion in regular sequence 0 5 JSQR JSQR injected sequence register 0x38 0x20 read-write 0x00000000 JL Injected sequence length 20 2 0 3 4 0x5 1-4 JSQ%s %s conversion in injected sequence 0 5 0 18 4 0x4 1-4 JDR%s JDR%s injected data register x 0x3C 0x20 read-only 0x00000000 JDATA Injected data 0 16 DR DR regular data register 0x4C 0x20 read-only 0x00000000 DATA Regular data 0 16 ADC2 0x40012100 ADC3 0x40012200 DAC Digital-to-analog converter DAC 0x40007400 0x0 0x400 registers CR CR control register 0x0 0x20 read-write 0x00000000 2 0x10 1-2 DMAUDRIE%s DAC channel%s DMA Underrun Interrupt enable 13 1 DMAUDRIE1 Disabled DAC channel X DMA Underrun Interrupt disabled 0 Enabled DAC channel X DMA Underrun Interrupt enabled 1 2 0x10 1-2 DMAEN%s DAC channel%s DMA enable 12 1 DMAEN1 Disabled DAC channel X DMA mode disabled 0 Enabled DAC channel X DMA mode enabled 1 2 0x10 1-2 MAMP%s DAC channel%s mask/amplitude selector 8 4 MAMP1 Amp1 Unmask bit0 of LFSR/ triangle amplitude equal to 1 0 Amp3 Unmask bits[1:0] of LFSR/ triangle amplitude equal to 3 1 Amp7 Unmask bits[2:0] of LFSR/ triangle amplitude equal to 7 2 Amp15 Unmask bits[3:0] of LFSR/ triangle amplitude equal to 15 3 Amp31 Unmask bits[4:0] of LFSR/ triangle amplitude equal to 31 4 Amp63 Unmask bits[5:0] of LFSR/ triangle amplitude equal 63 5 Amp127 Unmask bits[6:0] of LFSR/ triangle amplitude equal to 127 6 Amp255 Unmask bits[7:0] of LFSR/ triangle amplitude equal to 255 7 Amp511 Unmask bits[8:0] of LFSR/ triangle amplitude equal to 511 8 Amp1023 Unmask bits[9:0] of LFSR/ triangle amplitude equal to 1023 9 Amp2047 Unmask bits[10:0] of LFSR/ triangle amplitude equal to 2047 10 Amp4095 Unmask bits[11:0] of LFSR/ triangle amplitude equal to 4095 true 2 0x10 1-2 WAVE%s DAC channel%s noise/triangle wave generation enable 6 2 WAVE1 Disabled Wave generation disabled 0 Noise Noise wave generation enabled 1 Triangle Triangle wave generation enabled true TSEL1 DAC channel1 trigger selection 3 3 TSEL1 Tim6Trgo Timer 6 TRGO event 0 Tim8Trgo Timer 8 TRGO event 1 Tim7Trgo Timer 7 TRGO event 2 Tim5Trgo Timer 5 TRGO event 3 Tim2Trgo Timer 2 TRGO event 4 Tim4Trgo Timer 4 TRGO event 5 Exti9 EXTI line 9 6 Swtrig Software trigger 7 TSEL2 DAC channel2 trigger selection 19 3 2 0x10 1-2 TEN%s DAC channel%s trigger enable 2 1 TEN1 Disabled DAC channel X trigger disabled 0 Enabled DAC channel X trigger enabled 1 2 0x10 1-2 BOFF%s DAC channel%s output buffer disable 1 1 BOFF1 Enabled DAC channel X output buffer enabled 0 Disabled DAC channel X output buffer disabled 1 2 0x10 1-2 EN%s DAC channel%s enable 0 1 EN1 Disabled DAC channel X disabled 0 Enabled DAC channel X enabled 1 SWTRIGR SWTRIGR software trigger register 0x4 0x20 write-only 0x00000000 2 0x1 1-2 SWTRIG%s DAC channel%s software trigger 0 1 SWTRIG1 Disabled DAC channel X software trigger disabled 0 Enabled DAC channel X software trigger enabled 1 2 0xC 1-2 DHR12R%s DHR12R%s channel%s 12-bit right-aligned data holding register 0x8 0x20 read-write 0x00000000 DACCDHR DAC channel1 12-bit right-aligned data 0 12 0 4095 2 0xC 1-2 DHR12L%s DHR12L%s channel%s 12-bit left aligned data holding register 0xC 0x20 read-write 0x00000000 DACCDHR DAC channel1 12-bit left-aligned data 4 12 0 4095 2 0xC 1-2 DHR8R%s DHR8R%s channel%s 8-bit right aligned data holding register 0x10 0x20 read-write 0x00000000 DACCDHR DAC channel1 8-bit right-aligned data 0 8 0 255 DHR12RD DHR12RD Dual DAC 12-bit right-aligned data holding register 0x20 0x20 read-write 0x00000000 2 0x10 1-2 DACC%sDHR DAC channel%s 12-bit right-aligned data 0 12 0 4095 DHR12LD DHR12LD DUAL DAC 12-bit left aligned data holding register 0x24 0x20 read-write 0x00000000 2 0x10 1-2 DACC%sDHR DAC channel%s 12-bit left-aligned data 4 12 0 4095 DHR8RD DHR8RD DUAL DAC 8-bit right aligned data holding register 0x28 0x20 read-write 0x00000000 2 0x8 1-2 DACC%sDHR DAC channel%s 8-bit right-aligned data 0 8 0 255 2 0x4 1-2 DOR%s DOR%s channel%s data output register 0x2C 0x20 read-only 0x00000000 DACCDOR DAC channel1 data output 0 12 SR SR status register 0x34 0x20 read-write 0x00000000 2 0x10 1-2 DMAUDR%s DAC channel%s DMA underrun flag 13 1 DMAUDR1 NoUnderrun No DMA underrun error condition occurred for DAC channel x 0 Underrun DMA underrun error condition occurred for DAC channel x (the currently selected trigger is driving DAC channel1 conversion at a frequency higher than the DMA service capability rate) 1 PWR Power control PWR 0x40007000 0x0 0x400 registers CR1 CR1 power control register 0x0 0x20 read-write 0x0000C000 LPDS Low-power deep sleep 0 1 PDDS Power down deepsleep 1 1 PDDS STOP_MODE Enter Stop mode when the CPU enters deepsleep 0 STANDBY_MODE Enter Standby mode when the CPU enters deepsleep 1 CSBF Clear standby flag 3 1 PVDE Power voltage detector enable 4 1 PLS PVD level selection 5 3 DBP Disable backup domain write protection 8 1 FPDS Flash power down in Stop mode 9 1 LPUDS Low-power regulator in deepsleep under-drive mode 10 1 MRUDS Main regulator in deepsleep under-drive mode 11 1 ADCDC1 ADCDC1 13 1 VOS Regulator voltage scaling output selection 14 2 VOS SCALE3 Scale 3 mode 1 SCALE2 Scale 2 mode 2 SCALE1 Scale 1 mode (reset value) 3 ODEN Over-drive enable 16 1 ODSWEN Over-drive switching enabled 17 1 UDEN Under-drive enable in stop mode 18 2 CSR1 CSR1 power control/status register 0x4 0x20 0x00000000 WUIF Wakeup internal flag 0 1 read-only SBF Standby flag 1 1 read-only PVDO PVD output 2 1 read-only BRR Backup regulator ready 3 1 read-only BRE Backup regulator enable 9 1 read-write VOSRDY Regulator voltage scaling output selection ready bit 14 1 read-write ODRDY Over-drive mode ready 16 1 read-write ODSWRDY Over-drive mode switching ready 17 1 read-write UDRDY Under-drive ready flag 18 2 read-write CR2 CR2 power control register 0x8 0x20 0x00000000 CWUPF1 Clear Wakeup Pin flag for PA0 0 1 read-only CWUPF2 Clear Wakeup Pin flag for PA2 1 1 read-only CWUPF3 Clear Wakeup Pin flag for PC1 2 1 read-only CWUPF4 Clear Wakeup Pin flag for PC13 3 1 read-only CWUPF5 Clear Wakeup Pin flag for PI8 4 1 read-only CWUPF6 Clear Wakeup Pin flag for PI11 5 1 read-only WUPP1 Wakeup pin polarity bit for PA0 8 1 read-write WUPP2 Wakeup pin polarity bit for PA2 9 1 read-write WUPP3 Wakeup pin polarity bit for PC1 10 1 read-write WUPP4 Wakeup pin polarity bit for PC13 11 1 read-write WUPP5 Wakeup pin polarity bit for PI8 12 1 read-write WUPP6 Wakeup pin polarity bit for PI11 13 1 read-write CSR2 CSR2 power control/status register 0xC 0x20 0x00000000 WUPF1 Wakeup Pin flag for PA0 0 1 read-only WUPF2 Wakeup Pin flag for PA2 1 1 read-only WUPF3 Wakeup Pin flag for PC1 2 1 read-only WUPF4 Wakeup Pin flag for PC13 3 1 read-only WUPF5 Wakeup Pin flag for PI8 4 1 read-only WUPF6 Wakeup Pin flag for PI11 5 1 read-only EWUP1 Enable Wakeup pin for PA0 8 1 read-write EWUP2 Enable Wakeup pin for PA2 9 1 read-write EWUP3 Enable Wakeup pin for PC1 10 1 read-write EWUP4 Enable Wakeup pin for PC13 11 1 read-write EWUP5 Enable Wakeup pin for PI8 12 1 read-write EWUP6 Enable Wakeup pin for PI11 13 1 read-write IWDG Independent watchdog IWDG 0x40003000 0x0 0x400 registers KR KR Key register 0x0 0x10 write-only 0x00000000 KEY Key value (write only, read 0000h) 0 16 KEY Unlock Enable access to PR, RLR and WINR registers 21845 Feed Feed watchdog with RLR register value 43690 Start Start the watchdog 52428 PR PR Prescaler register 0x4 0x10 read-write 0x00000000 PR Prescaler divider 0 3 PR DivideBy4 Divider /4 0 DivideBy8 Divider /8 1 DivideBy16 Divider /16 2 DivideBy32 Divider /32 3 DivideBy64 Divider /64 4 DivideBy128 Divider /128 5 DivideBy256 Divider /256 true RLR RLR Reload register 0x8 0x10 read-write 0x00000FFF RL Watchdog counter reload value 0 12 0 4095 SR SR Status register 0xC 0x10 read-only 0x00000000 RVU Watchdog counter reload value update 1 1 PVU Watchdog prescaler value update 0 1 WINR WINR Window register 0x10 0x10 read-write 0x00000000 WIN Watchdog counter window value 0 12 0 4095 WWDG Window watchdog WWDG 0x40002C00 0x0 0x400 registers WWDG Window Watchdog interrupt 0 CR CR Control register 0x0 0x10 read-write 0x0000007F WDGA Activation bit 7 1 WDGA Disabled Watchdog disabled 0 Enabled Watchdog enabled 1 T 7-bit counter (MSB to LSB) 0 7 0 127 CFR CFR Configuration register 0x4 0x10 read-write 0x0000007F EWI Early wakeup interrupt 9 1 EWIW write Enable interrupt occurs whenever the counter reaches the value 0x40 1 WDGTB Timer base 7 2 WDGTB Div1 Counter clock (PCLK1 div 4096) div 1 0 Div2 Counter clock (PCLK1 div 4096) div 2 1 Div4 Counter clock (PCLK1 div 4096) div 4 2 Div8 Counter clock (PCLK1 div 4096) div 8 3 W 7-bit window value 0 7 0 127 SR SR Status register 0x8 0x10 read-write 0x00000000 EWIF Early wakeup interrupt flag 0 1 zeroToClear EWIFR read Finished The EWI Interrupt Service Routine has been serviced 0 Pending The EWI Interrupt Service Routine has been triggered 1 EWIFW write Finished The EWI Interrupt Service Routine has been serviced 0 ADC_Common Common ADC registers ADC_Common 0x40012300 0x0 0x400 registers CSR CSR ADC Common status register 0x0 0x20 read-only 0x00000000 OVR1 Overrun flag of ADC 1 5 1 OVR1 NoOverrun No overrun occurred 0 Overrun Overrun occurred 1 OVR3 Overrun flag of ADC3 21 1 STRT1 Regular channel Start flag of ADC 1 4 1 STRT1 NotStarted No regular channel conversion started 0 Started Regular channel conversion has started 1 STRT3 Regular channel Start flag of ADC 3 20 1 JSTRT1 Injected channel Start flag of ADC 1 3 1 JSTRT1 NotStarted No injected channel conversion started 0 Started Injected channel conversion has started 1 JSTRT3 Injected channel Start flag of ADC 3 19 1 JEOC1 Injected channel end of conversion of ADC 1 2 1 JEOC1 NotComplete Conversion is not complete 0 Complete Conversion complete 1 JEOC3 Injected channel end of conversion of ADC 3 18 1 EOC1 End of conversion of ADC 1 1 1 EOC1 NotComplete Conversion is not complete 0 Complete Conversion complete 1 EOC3 End of conversion of ADC 3 17 1 AWD1 Analog watchdog flag of ADC 1 0 1 AWD1 NoEvent No analog watchdog event occurred 0 Event Analog watchdog event occurred 1 AWD3 Analog watchdog flag of ADC 3 16 1 OVR2 Overrun flag of ADC 2 13 1 STRT2 Regular channel Start flag of ADC 2 12 1 JSTRT2 Injected channel Start flag of ADC 2 11 1 JEOC2 Injected channel end of conversion of ADC 2 10 1 EOC2 End of conversion of ADC 2 9 1 AWD2 Analog watchdog flag of ADC 2 8 1 CCR CCR ADC common control register 0x4 0x20 read-write 0x00000000 TSVREFE Temperature sensor and VREFINT enable 23 1 TSVREFE Disabled Temperature sensor and V_REFINT channel disabled 0 Enabled Temperature sensor and V_REFINT channel enabled 1 VBATE VBAT enable 22 1 VBATE Disabled V_BAT channel disabled 0 Enabled V_BAT channel enabled 1 ADCPRE ADC prescaler 16 2 ADCPRE Div2 PCLK2 divided by 2 0 Div4 PCLK2 divided by 4 1 Div6 PCLK2 divided by 6 2 Div8 PCLK2 divided by 8 3 DMA Direct memory access mode for multi ADC mode 14 2 DMA Disabled DMA mode disabled 0 Mode1 DMA mode 1 enabled (2 / 3 half-words one by one - 1 then 2 then 3) 1 Mode2 DMA mode 2 enabled (2 / 3 half-words by pairs - 2&1 then 1&3 then 3&2) 2 Mode3 DMA mode 3 enabled (2 / 3 half-words by pairs - 2&1 then 1&3 then 3&2) 3 DDS DMA disable selection for multi-ADC mode 13 1 DDS Single No new DMA request is issued after the last transfer 0 Continuous DMA requests are issued as long as data are converted and DMA=01, 10 or 11 1 DELAY Delay between 2 sampling phases 8 4 0 15 MULTI Multi ADC mode selection 0 5 MULTI Independent All the ADCs independent: independent mode 0 DualRJ Dual ADC1 and ADC2, combined regular and injected simultaneous mode 1 DualRA Dual ADC1 and ADC2, combined regular and alternate trigger mode 2 DualJ Dual ADC1 and ADC2, injected simultaneous mode only 5 DualR Dual ADC1 and ADC2, regular simultaneous mode only 6 DualI Dual ADC1 and ADC2, interleaved mode only 7 DualA Dual ADC1 and ADC2, alternate trigger mode only 9 TripleRJ Triple ADC, regular and injected simultaneous mode 17 TripleRA Triple ADC, regular and alternate trigger mode 18 TripleJ Triple ADC, injected simultaneous mode only 21 TripleR Triple ADC, regular simultaneous mode only 22 TripleI Triple ADC, interleaved mode only 23 TripleA Triple ADC, alternate trigger mode only 24 CDR CDR ADC common regular data register for dual and triple modes 0x8 0x20 read-only 0x00000000 DATA2 2nd data item of a pair of regular conversions 16 16 DATA1 1st data item of a pair of regular conversions 0 16 TIM1 Advanced-timers TIM 0x40010000 0x0 0x400 registers TIM1_BRK_TIM9 TIM1 Break interrupt and TIM9 global interrupt 24 TIM1_TRG_COM_TIM11 TIM1 Trigger and Commutation interrupts and TIM11 global interrupt 26 CR1 CR1 control register 1 0x0 0x10 read-write 0x00000000 CKD Clock division 8 2 CKD Div1 t_DTS = t_CK_INT 0 Div2 t_DTS = 2 × t_CK_INT 1 Div4 t_DTS = 4 × t_CK_INT 2 ARPE Auto-reload preload enable 7 1 ARPE Disabled TIMx_APRR register is not buffered 0 Enabled TIMx_APRR register is buffered 1 CMS Center-aligned mode selection 5 2 CMS EdgeAligned The counter counts up or down depending on the direction bit 0 CenterAligned1 The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting down. 1 CenterAligned2 The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting up. 2 CenterAligned3 The counter counts up and down alternatively. Output compare interrupt flags are set both when the counter is counting up or down. 3 DIR Direction 4 1 DIR Up Counter used as upcounter 0 Down Counter used as downcounter 1 OPM One-pulse mode 3 1 OPM Disabled Counter is not stopped at update event 0 Enabled Counter stops counting at the next update event (clearing the CEN bit) 1 URS Update request source 2 1 URS AnyEvent Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request 0 CounterOnly Only counter overflow/underflow generates an update interrupt or DMA request 1 UDIS Update disable 1 1 UDIS Enabled Update event enabled 0 Disabled Update event disabled 1 CEN Counter enable 0 1 CEN Disabled Counter disabled 0 Enabled Counter enabled 1 UIFREMAP UIF status bit remapping 11 1 CR2 CR2 control register 2 0x4 0x20 read-write 0x00000000 6 0x2 1-6 OIS%s Output Idle state (OC%s output) 8 1 OIS1 Reset OCx=0 (after a dead-time if OCx(N) is implemented) when MOE=0 0 Set OCx=1 (after a dead-time if OCx(N) is implemented) when MOE=0 1 3 0x2 1-3 OIS%sN Output Idle state (OC%sN output) 9 1 OIS1N Reset OCxN=0 after a dead-time when MOE=0 0 Set OCxN=1 after a dead-time when MOE=0 1 TI1S TI1 selection 7 1 TI1S Normal The TIMx_CH1 pin is connected to TI1 input 0 XOR The TIMx_CH1, CH2, CH3 pins are connected to TI1 input 1 MMS Master mode selection 4 3 MMS Reset The UG bit from the TIMx_EGR register is used as trigger output 0 Enable The counter enable signal, CNT_EN, is used as trigger output 1 Update The update event is selected as trigger output 2 ComparePulse The trigger output send a positive pulse when the CC1IF flag it to be set, as soon as a capture or a compare match occurred 3 CompareOC1 OC1REF signal is used as trigger output 4 CompareOC2 OC2REF signal is used as trigger output 5 CompareOC3 OC3REF signal is used as trigger output 6 CompareOC4 OC4REF signal is used as trigger output 7 CCDS Capture/compare DMA selection 3 1 CCDS OnCompare CCx DMA request sent when CCx event occurs 0 OnUpdate CCx DMA request sent when update event occurs 1 CCUS Capture/compare control update selection 2 1 CCUS Sw When capture/compare control bits are preloaded (CCPC=1), they are updated by setting the COMG bit only 0 SwOrEdge When capture/compare control bits are preloaded (CCPC=1), they are updated by setting the COMG bit or when an rising edge occurs on TRGI 1 CCPC Capture/compare preloaded control 0 1 CCPC NotPreloaded CCxE, CCxNE and OCxM bits are not preloaded 0 Preloaded CCxE, CCxNE and OCxM bits are preloaded 1 MMS2 Master mode selection 2 20 4 SMCR SMCR slave mode control register 0x8 0x20 read-write 0x00000000 SMS_3 Slave model selection - bit[3] 16 1 ETP External trigger polarity 15 1 ETP NotInverted ETR is noninverted, active at high level or rising edge 0 Inverted ETR is inverted, active at low level or falling edge 1 ECE External clock enable 14 1 ECE Disabled External clock mode 2 disabled 0 Enabled External clock mode 2 enabled. The counter is clocked by any active edge on the ETRF signal. 1 ETPS External trigger prescaler 12 2 ETPS Div1 Prescaler OFF 0 Div2 ETRP frequency divided by 2 1 Div4 ETRP frequency divided by 4 2 Div8 ETRP frequency divided by 8 3 ETF External trigger filter 8 4 ETF NoFilter No filter, sampling is done at fDTS 0 FCK_INT_N2 fSAMPLING=fCK_INT, N=2 1 FCK_INT_N4 fSAMPLING=fCK_INT, N=4 2 FCK_INT_N8 fSAMPLING=fCK_INT, N=8 3 FDTS_Div2_N6 fSAMPLING=fDTS/2, N=6 4 FDTS_Div2_N8 fSAMPLING=fDTS/2, N=8 5 FDTS_Div4_N6 fSAMPLING=fDTS/4, N=6 6 FDTS_Div4_N8 fSAMPLING=fDTS/4, N=8 7 FDTS_Div8_N6 fSAMPLING=fDTS/8, N=6 8 FDTS_Div8_N8 fSAMPLING=fDTS/8, N=8 9 FDTS_Div16_N5 fSAMPLING=fDTS/16, N=5 10 FDTS_Div16_N6 fSAMPLING=fDTS/16, N=6 11 FDTS_Div16_N8 fSAMPLING=fDTS/16, N=8 12 FDTS_Div32_N5 fSAMPLING=fDTS/32, N=5 13 FDTS_Div32_N6 fSAMPLING=fDTS/32, N=6 14 FDTS_Div32_N8 fSAMPLING=fDTS/32, N=8 15 MSM Master/Slave mode 7 1 MSM NoSync No action 0 Sync The effect of an event on the trigger input (TRGI) is delayed to allow a perfect synchronization between the current timer and its slaves (through TRGO). It is useful if we want to synchronize several timers on a single external event. 1 TS Trigger selection 4 3 TS ITR0 Internal Trigger 0 (ITR0) 0 ITR1 Internal Trigger 1 (ITR1) 1 ITR2 Internal Trigger 2 (ITR2) 2 TI1F_ED TI1 Edge Detector (TI1F_ED) 4 TI1FP1 Filtered Timer Input 1 (TI1FP1) 5 TI2FP2 Filtered Timer Input 2 (TI2FP2) 6 ETRF External Trigger input (ETRF) 7 SMS Slave mode selection - bit[2:0] 0 3 SMS Disabled Slave mode disabled - if CEN = ‘1 then the prescaler is clocked directly by the internal clock. 0 Encoder_Mode_1 Encoder mode 1 - Counter counts up/down on TI2FP1 edge depending on TI1FP2 level. 1 Encoder_Mode_2 Encoder mode 2 - Counter counts up/down on TI1FP2 edge depending on TI2FP1 level. 2 Encoder_Mode_3 Encoder mode 3 - Counter counts up/down on both TI1FP1 and TI2FP2 edges depending on the level of the other input. 3 Reset_Mode Reset Mode - Rising edge of the selected trigger input (TRGI) reinitializes the counter and generates an update of the registers. 4 Gated_Mode Gated Mode - The counter clock is enabled when the trigger input (TRGI) is high. The counter stops (but is not reset) as soon as the trigger becomes low. Both start and stop of the counter are controlled. 5 Trigger_Mode Trigger Mode - The counter starts at a rising edge of the trigger TRGI (but it is not reset). Only the start of the counter is controlled. 6 Ext_Clock_Mode External Clock Mode 1 - Rising edges of the selected trigger (TRGI) clock the counter. 7 DIER DIER DMA/Interrupt enable register 0xC 0x10 read-write 0x00000000 TDE Trigger DMA request enable 14 1 TDE Disabled Trigger DMA request disabled 0 Enabled Trigger DMA request enabled 1 COMDE COM DMA request enable 13 1 COMDE Disabled COM DMA request disabled 0 Enabled COM DMA request enabled 1 4 0x1 1-4 CC%sDE Capture/Compare %s DMA request enable 9 1 CC1DE Disabled CCx DMA request disabled 0 Enabled CCx DMA request enabled 1 UDE Update DMA request enable 8 1 UDE Disabled Update DMA request disabled 0 Enabled Update DMA request enabled 1 TIE Trigger interrupt enable 6 1 TIE Disabled Trigger interrupt disabled 0 Enabled Trigger interrupt enabled 1 4 0x1 1-4 CC%sIE Capture/Compare %s interrupt enable 1 1 CC1IE Disabled CCx interrupt disabled 0 Enabled CCx interrupt enabled 1 UIE Update interrupt enable 0 1 UIE Disabled Update interrupt disabled 0 Enabled Update interrupt enabled 1 BIE Break interrupt enable 7 1 BIE Disabled Break interrupt disabled 0 Enabled Break interrupt enabled 1 COMIE COM interrupt enable 5 1 COMIE Disabled COM interrupt disabled 0 Enabled COM interrupt enabled 1 SR SR status register 0x10 0x20 read-write 0x00000000 4 0x1 1-4 CC%sOF Capture/Compare %s overcapture flag 9 1 zeroToClear CC1OFR read NoOvercapture No overcapture has been detected 0 Overcapture The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set 1 CC1OFW write Clear Clear flag 0 BIF Break interrupt flag 7 1 zeroToClear BIFR read NoTrigger No break event occurred 0 Trigger An active level has been detected on the break input. An interrupt is generated if BIE=1 in the TIMx_DIER register 1 BIFW write Clear Clear flag 0 TIF Trigger interrupt flag 6 1 zeroToClear TIFR read NoTrigger No trigger event occurred 0 Trigger Trigger interrupt pending 1 TIFW write Clear Clear flag 0 COMIF COM interrupt flag 5 1 zeroToClear COMIFR read NoCOM No COM event occurred 0 COM COM interrupt pending 1 COMIFW write Clear Clear flag 0 4 0x1 1-4 CC%sIF Capture/compare %s interrupt flag 1 1 zeroToClear CC1IFR read NoMatch No campture/compare has been detected 0 Match If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register. 1 CC1IFW write Clear Clear flag 0 UIF Update interrupt flag 0 1 zeroToClear UIFR read NoUpdateOccurred No update occurred 0 UpdatePending Update interrupt pending 1 UIFW write Clear Clear flag 0 B2IF Break 2 interrupt flag 8 1 zeroToClear B2IFR read NoTrigger No break event occurred 0 Trigger An active level has been detected on the break 2 input. An interrupt is generated if BIE=1 in the TIMx_DIER register 1 B2IFW write Clear Clear flag 0 CC5IF Compare 5 interrupt flag 16 1 zeroToClear read write CC6IF Compare 6 interrupt flag 17 1 zeroToClear read write EGR EGR event generation register 0x14 0x10 write-only 0x00000000 BG Break generation 7 1 BGW Trigger A break event is generated. MOE bit is cleared and BIF flag is set. Related interrupt or DMA transfer can occur if enabled 1 TG Trigger generation 6 1 TGW Trigger The TIF flag is set in TIMx_SR register. Related interrupt or DMA transfer can occur if enabled. 1 COMG Capture/Compare control update generation 5 1 COMGW Trigger When CCPC bit is set, it allows CCxE, CCxNE and OCxM bits to be updated 1 4 0x1 1-4 CC%sG Capture/compare %s generation 1 1 CC1GW Trigger If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register. 1 UG Update generation 0 1 UG Update Re-initializes the timer counter and generates an update of the registers. 1 B2G Break 2 generation 8 1 B2GW Trigger A break 2 event is generated. MOE bit is cleared and B2IF flag is set. Related interrupt can occur if enabled 1 CCMR1_Output CCMR1_Output capture/compare mode register 1 (output mode) 0x18 0x20 read-write 0x00000000 2 0x8 1-2 OC%sCE Output compare %s clear enable 7 1 OC1CE Disabled OCxRef is not affected by the ETRF signal 0 Enabled OCxRef is cleared as soon as a High level is detected on ETRF signal 1 2 0x8 1-2 OC%sM Output compare %s mode 4 3 OC1M Frozen The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive 0 ActiveOnMatch Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1 1 InactiveOnMatch Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved 2 Toggle OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved 3 ForceInactive OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF 4 ForceActive OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF 5 PwmMode1 In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down 6 PwmMode2 Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1 7 2 0x8 1-2 OC%sPE Output compare %s preload enable 3 1 OC1PE Disabled Preload register on CCRx disabled. New values written to CCRx are taken into account immediately 0 Enabled Preload register on CCRx enabled. Preload value is loaded into active register on each update event 1 2 0x8 1-2 OC%sFE Output compare %s fast enable 2 1 OC1FE Disabled Fast output disabled 0 Enabled Fast output enabled 1 2 0x8 1-2 CC%sS Capture/Compare %s selection 0 2 CC1S Output CCx channel is configured as output 0 2 0x8 1-2 OC%sM_3 Output compare %s mode, bit 3 16 1 OC1M_3 Normal Normal output compare mode (modes 0-7) 0 Extended Extended output compare mode (modes 7-15) 1 CCMR1_Input CCMR1_Input capture/compare mode register 1 (input mode) CCMR1_Output 0x18 0x20 read-write 0x00000000 2 0x8 1-2 IC%sF Input capture %s filter 4 4 ICFilter NoFilter No filter, sampling is done at fDTS 0 FCK_INT_N2 fSAMPLING=fCK_INT, N=2 1 FCK_INT_N4 fSAMPLING=fCK_INT, N=4 2 FCK_INT_N8 fSAMPLING=fCK_INT, N=8 3 FDTS_Div2_N6 fSAMPLING=fDTS/2, N=6 4 FDTS_Div2_N8 fSAMPLING=fDTS/2, N=8 5 FDTS_Div4_N6 fSAMPLING=fDTS/4, N=6 6 FDTS_Div4_N8 fSAMPLING=fDTS/4, N=8 7 FDTS_Div8_N6 fSAMPLING=fDTS/8, N=6 8 FDTS_Div8_N8 fSAMPLING=fDTS/8, N=8 9 FDTS_Div16_N5 fSAMPLING=fDTS/16, N=5 10 FDTS_Div16_N6 fSAMPLING=fDTS/16, N=6 11 FDTS_Div16_N8 fSAMPLING=fDTS/16, N=8 12 FDTS_Div32_N5 fSAMPLING=fDTS/32, N=5 13 FDTS_Div32_N6 fSAMPLING=fDTS/32, N=6 14 FDTS_Div32_N8 fSAMPLING=fDTS/32, N=8 15 2 0x8 1-2 IC%sPSC Input capture %s prescaler 2 2 ICPrescaler NoPrescaler No prescaler, capture is done each time an edge is detected on the capture input 0 TwoEvents Capture is done once every 2 events 1 FourEvents Capture is done once every 4 events 2 EightEvents Capture is done once every 8 events 3 CC2S Capture/Compare 2 selection 8 2 CC2S TI2 CC2 channel is configured as input, IC2 is mapped on TI2 1 TI1 CC2 channel is configured as input, IC2 is mapped on TI1 2 TRC CC2 channel is configured as input, IC2 is mapped on TRC 3 CC1S Capture/Compare 1 selection 0 2 CC1S TI1 CC1 channel is configured as input, IC1 is mapped on TI1 1 TI2 CC1 channel is configured as input, IC1 is mapped on TI2 2 TRC CC1 channel is configured as input, IC1 is mapped on TRC 3 CCMR2_Output CCMR2_Output capture/compare mode register 2 (output mode) 0x1C 0x20 read-write 0x00000000 2 0x8 3-4 OC%sCE Output compare %s clear enable 7 1 2 0x8 3-4 OC%sM Output compare %s mode 4 3 2 0x8 3-4 OC%sPE Output compare %s preload enable 3 1 2 0x8 3-4 OC%sFE Output compare %s fast enable 2 1 2 0x8 3-4 CC%sS Capture/Compare %s selection 0 2 2 0x8 3-4 OC%sM_3 Output compare %s mode, bit 3 16 1 CCMR2_Input CCMR2_Input capture/compare mode register 2 (input mode) CCMR2_Output 0x1C 0x20 read-write 0x00000000 2 0x8 3-4 IC%sF Input capture %s filter 4 4 2 0x8 3-4 IC%sPSC Input capture %s prescaler 2 2 CC4S Capture/Compare 4 selection 8 2 CC4S TI4 CC4 channel is configured as input, IC4 is mapped on TI4 1 TI3 CC4 channel is configured as input, IC4 is mapped on TI3 2 TRC CC4 channel is configured as input, IC4 is mapped on TRC 3 CC3S Capture/compare 3 selection 0 2 CC3S TI3 CC3 channel is configured as input, IC3 is mapped on TI3 1 TI4 CC3 channel is configured as input, IC3 is mapped on TI4 2 TRC CC3 channel is configured as input, IC3 is mapped on TRC 3 CCER CCER capture/compare enable register 0x20 0x20 read-write 0x00000000 6 0x4 1-6 CC%sP Capture/Compare %s output Polarity 1 1 CC1P RisingEdge Noninverted/rising edge 0 FallingEdge Inverted/falling edge 1 6 0x4 1-6 CC%sE Capture/Compare %s output enable 0 1 CC1E Disabled Capture disabled 0 Enabled Capture enabled 1 4 0x4 1-4 CC%sNP Capture/Compare %s output Polarity 3 1 CC1NP ActiveHigh OCxN active high 0 ActiveLow OCxN active low 1 3 0x4 1-3 CC%sNE Capture/Compare %s complementary output enable 2 1 CC1NE Disabled Complementary output disabled 0 Enabled Complementary output enabled 1 CNT CNT counter 0x24 0x20 read-write 0x00000000 CNT counter value 0 16 0 65535 UIFCPY UIF copy This bit is a read-only copy of the UIF bit of the TIMx_ISR register. If the UIFREMAP bit in the TIMxCR1 is reset, bit 31 is reserved and read at 0 31 1 read-only CNT16 CNT16 16-bit counter register CNT 0x24 0x10 read-write 0x00000000 CNT counter value 0 16 read-write 0 65535 PSC PSC prescaler 0x28 0x10 read-write 0x00000000 PSC Prescaler value 0 16 0 65535 ARR ARR auto-reload register 0x2C 0x10 read-write 0x0000FFFF ARR Auto-reload value 0 16 0 65535 4 0x4 1-4 CCR%s CCR%s capture/compare register 0x34 0x10 read-write 0x00000000 CCR Capture/Compare value 0 16 0 65535 DCR DCR DMA control register 0x48 0x10 read-write 0x00000000 DBL DMA burst length 8 5 0 18 DBA DMA base address 0 5 0 31 DMAR DMAR DMA address for full transfer 0x4C 0x20 read-write 0x00000000 DMAB DMA register for burst accesses 0 32 RCR RCR repetition counter register 0x30 0x20 read-write 0x00000000 REP Repetition counter value 0 16 0 65535 BDTR BDTR break and dead-time register 0x44 0x20 read-write 0x00000000 MOE Main output enable 15 1 MOE DisabledIdle OC/OCN are disabled or forced idle depending on OSSI 0 Enabled OC/OCN are enabled if CCxE/CCxNE are set 1 AOE Automatic output enable 14 1 AOE Manual MOE can be set only by software 0 Automatic MOE can be set by software or automatically at the next update event (if none of the break inputs BRK and BRK2 is active) 1 BKP Break polarity 13 1 BKP ActiveLow Break input BRKx is active low 0 ActiveHigh Break input BRKx is active high 1 BKE Break enable 12 1 BKE Disabled Break function x disabled 0 Enabled Break function x enabled 1 OSSR Off-state selection for Run mode 11 1 OSSR HiZ When inactive, OC/OCN outputs are disabled 0 IdleLevel When inactive, OC/OCN outputs are enabled with their inactive level 1 OSSI Off-state selection for Idle mode 10 1 OSSI HiZ When inactive, OC/OCN outputs are disabled 0 IdleLevel When inactive, OC/OCN outputs are forced to idle level 1 LOCK Lock configuration 8 2 LOCK Off No bit is write protected 0 Level1 Any bits except MOE, OSSR, OSSI and LOCK in TIMx_BDTR register, OISx and OISxN bits in TIMx_CR2 register can no longer be written 1 Level2 LOCK Level 1 + CC Polarity bits (CCxP/CCxNP bits in TIMx_CCER register, as long as the related channel is configured in output through the CCxS bits) as well as OSSR and OSSI bits can no longer be written 2 Level3 LOCK Level 2 + CC Control bits (OCxM and OCxPE bits in TIMx_CCMRx registers, as long as the related channel is configured in output through the CCxS bits) can no longer be written 3 DTG Dead-time generator setup 0 8 0 255 BKF Break filter 16 4 BK2F Break 2 filter 20 4 BK2E Break 2 enable 24 1 BK2P Break 2 polarity 25 1 CCMR3_Output CCMR3_Output capture/compare mode register 3 (output mode) 0x54 0x20 read-write 0x00000000 2 0x8 5-6 OC%sFE Output compare %s fast enable 2 1 2 0x8 5-6 OC%sPE Output compare %s preload enable 3 1 2 0x8 5-6 OC%sM Output compare %s mode 4 3 2 0x8 5-6 OC%sCE Output compare %s clear enable 7 1 2 0x8 5-6 OC%sM_3 Output compare %s mode, bit 3 16 1 CCR5 CCR5 capture/compare register 0x58 0x20 read-write 0x00000000 CCR Capture/Compare value 0 16 0 65535 GC5C1 Group Channel 5 and Channel 1 29 1 GC5C2 Group Channel 5 and Channel 2 30 1 GC5C3 Group Channel 5 and Channel 3 31 1 CCR6 CRR6 capture/compare register 0x5C 0x10 read-write 0x00000000 CCR Capture/Compare value 0 16 0 65535 TIM8 TIM 0x40010400 TIM8_BRK_TIM12 TIM8 Break interrupt and TIM12 global interrupt 43 TIM8_UP_TIM13 TIM8 Update interrupt and TIM13 global interrupt 44 TIM8_TRG_COM_TIM14 TIM8 Trigger and Commutation interrupts and TIM14 global interrupt 45 TIM8_CC TIM8 Capture Compare interrupt 46 TIM2 General purpose timers TIM 0x40000000 0x0 0x400 registers TIM2 TIM2 global interrupt 28 CR1 CR1 control register 1 0x0 0x10 read-write 0x00000000 CKD Clock division 8 2 CKD Div1 t_DTS = t_CK_INT 0 Div2 t_DTS = 2 × t_CK_INT 1 Div4 t_DTS = 4 × t_CK_INT 2 ARPE Auto-reload preload enable 7 1 ARPE Disabled TIMx_APRR register is not buffered 0 Enabled TIMx_APRR register is buffered 1 CMS Center-aligned mode selection 5 2 CMS EdgeAligned The counter counts up or down depending on the direction bit 0 CenterAligned1 The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting down. 1 CenterAligned2 The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting up. 2 CenterAligned3 The counter counts up and down alternatively. Output compare interrupt flags are set both when the counter is counting up or down. 3 DIR Direction 4 1 DIR Up Counter used as upcounter 0 Down Counter used as downcounter 1 OPM One-pulse mode 3 1 OPM Disabled Counter is not stopped at update event 0 Enabled Counter stops counting at the next update event (clearing the CEN bit) 1 URS Update request source 2 1 URS AnyEvent Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request 0 CounterOnly Only counter overflow/underflow generates an update interrupt or DMA request 1 UDIS Update disable 1 1 UDIS Enabled Update event enabled 0 Disabled Update event disabled 1 CEN Counter enable 0 1 CEN Disabled Counter disabled 0 Enabled Counter enabled 1 UIFREMAP UIF status bit remapping 11 1 CR2 CR2 control register 2 0x4 0x10 read-write 0x00000000 TI1S TI1 selection 7 1 TI1S Normal The TIMx_CH1 pin is connected to TI1 input 0 XOR The TIMx_CH1, CH2, CH3 pins are connected to TI1 input 1 MMS Master mode selection 4 3 MMS Reset The UG bit from the TIMx_EGR register is used as trigger output 0 Enable The counter enable signal, CNT_EN, is used as trigger output 1 Update The update event is selected as trigger output 2 ComparePulse The trigger output send a positive pulse when the CC1IF flag it to be set, as soon as a capture or a compare match occurred 3 CompareOC1 OC1REF signal is used as trigger output 4 CompareOC2 OC2REF signal is used as trigger output 5 CompareOC3 OC3REF signal is used as trigger output 6 CompareOC4 OC4REF signal is used as trigger output 7 CCDS Capture/compare DMA selection 3 1 CCDS OnCompare CCx DMA request sent when CCx event occurs 0 OnUpdate CCx DMA request sent when update event occurs 1 SMCR SMCR slave mode control register 0x8 0x20 read-write 0x00000000 SMS Slave mode selection 0 3 SMS Disabled Slave mode disabled - if CEN = ‘1 then the prescaler is clocked directly by the internal clock. 0 Encoder_Mode_1 Encoder mode 1 - Counter counts up/down on TI2FP1 edge depending on TI1FP2 level. 1 Encoder_Mode_2 Encoder mode 2 - Counter counts up/down on TI1FP2 edge depending on TI2FP1 level. 2 Encoder_Mode_3 Encoder mode 3 - Counter counts up/down on both TI1FP1 and TI2FP2 edges depending on the level of the other input. 3 Reset_Mode Reset Mode - Rising edge of the selected trigger input (TRGI) reinitializes the counter and generates an update of the registers. 4 Gated_Mode Gated Mode - The counter clock is enabled when the trigger input (TRGI) is high. The counter stops (but is not reset) as soon as the trigger becomes low. Both start and stop of the counter are controlled. 5 Trigger_Mode Trigger Mode - The counter starts at a rising edge of the trigger TRGI (but it is not reset). Only the start of the counter is controlled. 6 Ext_Clock_Mode External Clock Mode 1 - Rising edges of the selected trigger (TRGI) clock the counter. 7 TS Trigger selection 4 3 TS ITR0 Internal Trigger 0 (ITR0) 0 ITR1 Internal Trigger 1 (ITR1) 1 ITR2 Internal Trigger 2 (ITR2) 2 TI1F_ED TI1 Edge Detector (TI1F_ED) 4 TI1FP1 Filtered Timer Input 1 (TI1FP1) 5 TI2FP2 Filtered Timer Input 2 (TI2FP2) 6 ETRF External Trigger input (ETRF) 7 MSM Master/Slave mode 7 1 MSM NoSync No action 0 Sync The effect of an event on the trigger input (TRGI) is delayed to allow a perfect synchronization between the current timer and its slaves (through TRGO). It is useful if we want to synchronize several timers on a single external event. 1 ETF External trigger filter 8 4 ETF NoFilter No filter, sampling is done at fDTS 0 FCK_INT_N2 fSAMPLING=fCK_INT, N=2 1 FCK_INT_N4 fSAMPLING=fCK_INT, N=4 2 FCK_INT_N8 fSAMPLING=fCK_INT, N=8 3 FDTS_Div2_N6 fSAMPLING=fDTS/2, N=6 4 FDTS_Div2_N8 fSAMPLING=fDTS/2, N=8 5 FDTS_Div4_N6 fSAMPLING=fDTS/4, N=6 6 FDTS_Div4_N8 fSAMPLING=fDTS/4, N=8 7 FDTS_Div8_N6 fSAMPLING=fDTS/8, N=6 8 FDTS_Div8_N8 fSAMPLING=fDTS/8, N=8 9 FDTS_Div16_N5 fSAMPLING=fDTS/16, N=5 10 FDTS_Div16_N6 fSAMPLING=fDTS/16, N=6 11 FDTS_Div16_N8 fSAMPLING=fDTS/16, N=8 12 FDTS_Div32_N5 fSAMPLING=fDTS/32, N=5 13 FDTS_Div32_N6 fSAMPLING=fDTS/32, N=6 14 FDTS_Div32_N8 fSAMPLING=fDTS/32, N=8 15 ETPS External trigger prescaler 12 2 ETPS Div1 Prescaler OFF 0 Div2 ETRP frequency divided by 2 1 Div4 ETRP frequency divided by 4 2 Div8 ETRP frequency divided by 8 3 ECE External clock enable 14 1 ECE Disabled External clock mode 2 disabled 0 Enabled External clock mode 2 enabled. The counter is clocked by any active edge on the ETRF signal. 1 ETP External trigger polarity 15 1 ETP NotInverted ETR is noninverted, active at high level or rising edge 0 Inverted ETR is inverted, active at low level or falling edge 1 SMS_3 Slave model selection - bit[3] 16 1 DIER DIER DMA/Interrupt enable register 0xC 0x10 read-write 0x00000000 TDE Trigger DMA request enable 14 1 TDE Disabled Trigger DMA request disabled 0 Enabled Trigger DMA request enabled 1 4 0x1 1-4 CC%sDE Capture/Compare %s DMA request enable 9 1 CC1DE Disabled CCx DMA request disabled 0 Enabled CCx DMA request enabled 1 UDE Update DMA request enable 8 1 UDE Disabled Update DMA request disabled 0 Enabled Update DMA request enabled 1 TIE Trigger interrupt enable 6 1 TIE Disabled Trigger interrupt disabled 0 Enabled Trigger interrupt enabled 1 4 0x1 1-4 CC%sIE Capture/Compare %s interrupt enable 1 1 CC1IE Disabled CCx interrupt disabled 0 Enabled CCx interrupt enabled 1 UIE Update interrupt enable 0 1 UIE Disabled Update interrupt disabled 0 Enabled Update interrupt enabled 1 SR SR status register 0x10 0x10 read-write 0x00000000 4 0x1 1-4 CC%sOF Capture/Compare %s overcapture flag 9 1 zeroToClear CC1OFR read NoOvercapture No overcapture has been detected 0 Overcapture The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set 1 CC1OFW write Clear Clear flag 0 TIF Trigger interrupt flag 6 1 zeroToClear TIFR read NoTrigger No trigger event occurred 0 Trigger Trigger interrupt pending 1 TIFW write Clear Clear flag 0 4 0x1 1-4 CC%sIF Capture/compare %s interrupt flag 1 1 zeroToClear CC1IFR read NoMatch No campture/compare has been detected 0 Match If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register. 1 CC1IFW write Clear Clear flag 0 UIF Update interrupt flag 0 1 zeroToClear UIFR read NoUpdateOccurred No update occurred 0 UpdatePending Update interrupt pending 1 UIFW write Clear Clear flag 0 EGR EGR event generation register 0x14 0x10 write-only 0x00000000 TG Trigger generation 6 1 TGW Trigger The TIF flag is set in TIMx_SR register. Related interrupt or DMA transfer can occur if enabled. 1 4 0x1 1-4 CC%sG Capture/compare %s generation 1 1 CC1GW Trigger If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register. 1 UG Update generation 0 1 UG Update Re-initializes the timer counter and generates an update of the registers. 1 CCMR1_Output CCMR1_Output capture/compare mode register 1 (output mode) 0x18 0x20 read-write 0x00000000 2 0x8 1-2 OC%sCE Output compare %s clear enable 7 1 OC1CE Disabled OCxRef is not affected by the ETRF signal 0 Enabled OCxRef is cleared as soon as a High level is detected on ETRF signal 1 2 0x8 1-2 OC%sM Output compare %s mode 4 3 OC1M Frozen The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive 0 ActiveOnMatch Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1 1 InactiveOnMatch Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved 2 Toggle OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved 3 ForceInactive OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF 4 ForceActive OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF 5 PwmMode1 In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down 6 PwmMode2 Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1 7 2 0x8 1-2 OC%sPE Output compare %s preload enable 3 1 OC1PE Disabled Preload register on CCRx disabled. New values written to CCRx are taken into account immediately 0 Enabled Preload register on CCRx enabled. Preload value is loaded into active register on each update event 1 2 0x8 1-2 OC%sFE Output compare %s fast enable 2 1 OC1FE Disabled Fast output disabled 0 Enabled Fast output enabled 1 2 0x8 1-2 CC%sS Capture/Compare %s selection 0 2 CC1S Output CCx channel is configured as output 0 2 0x8 1-2 OC%sM_3 Output compare %s mode, bit 3 16 1 OC1M_3 Normal Normal output compare mode (modes 0-7) 0 Extended Extended output compare mode (modes 7-15) 1 CCMR1_Input CCMR1_Input capture/compare mode register 1 (input mode) CCMR1_Output 0x18 0x20 read-write 0x00000000 2 0x8 1-2 IC%sF Input capture %s filter 4 4 ICFilter NoFilter No filter, sampling is done at fDTS 0 FCK_INT_N2 fSAMPLING=fCK_INT, N=2 1 FCK_INT_N4 fSAMPLING=fCK_INT, N=4 2 FCK_INT_N8 fSAMPLING=fCK_INT, N=8 3 FDTS_Div2_N6 fSAMPLING=fDTS/2, N=6 4 FDTS_Div2_N8 fSAMPLING=fDTS/2, N=8 5 FDTS_Div4_N6 fSAMPLING=fDTS/4, N=6 6 FDTS_Div4_N8 fSAMPLING=fDTS/4, N=8 7 FDTS_Div8_N6 fSAMPLING=fDTS/8, N=6 8 FDTS_Div8_N8 fSAMPLING=fDTS/8, N=8 9 FDTS_Div16_N5 fSAMPLING=fDTS/16, N=5 10 FDTS_Div16_N6 fSAMPLING=fDTS/16, N=6 11 FDTS_Div16_N8 fSAMPLING=fDTS/16, N=8 12 FDTS_Div32_N5 fSAMPLING=fDTS/32, N=5 13 FDTS_Div32_N6 fSAMPLING=fDTS/32, N=6 14 FDTS_Div32_N8 fSAMPLING=fDTS/32, N=8 15 2 0x8 1-2 IC%sPSC Input capture %s prescaler 2 2 ICPrescaler NoPrescaler No prescaler, capture is done each time an edge is detected on the capture input 0 TwoEvents Capture is done once every 2 events 1 FourEvents Capture is done once every 4 events 2 EightEvents Capture is done once every 8 events 3 CC2S Capture/Compare 2 selection 8 2 CC2S TI2 CC2 channel is configured as input, IC2 is mapped on TI2 1 TI1 CC2 channel is configured as input, IC2 is mapped on TI1 2 TRC CC2 channel is configured as input, IC2 is mapped on TRC 3 CC1S Capture/Compare 1 selection 0 2 CC1S TI1 CC1 channel is configured as input, IC1 is mapped on TI1 1 TI2 CC1 channel is configured as input, IC1 is mapped on TI2 2 TRC CC1 channel is configured as input, IC1 is mapped on TRC 3 CCMR2_Output CCMR2_Output capture/compare mode register 2 (output mode) 0x1C 0x20 read-write 0x00000000 2 0x8 3-4 OC%sCE Output compare %s clear enable 7 1 2 0x8 3-4 OC%sM Output compare %s mode 4 3 2 0x8 3-4 OC%sPE Output compare %s preload enable 3 1 2 0x8 3-4 OC%sFE Output compare %s fast enable 2 1 2 0x8 3-4 CC%sS Capture/Compare %s selection 0 2 2 0x8 3-4 OC%sM_3 Output compare %s mode, bit 3 16 1 CCMR2_Input CCMR2_Input capture/compare mode register 2 (input mode) CCMR2_Output 0x1C 0x20 read-write 0x00000000 2 0x8 3-4 IC%sF Input capture %s filter 4 4 2 0x8 3-4 IC%sPSC Input capture %s prescaler 2 2 CC4S Capture/Compare 4 selection 8 2 CC4S TI4 CC4 channel is configured as input, IC4 is mapped on TI4 1 TI3 CC4 channel is configured as input, IC4 is mapped on TI3 2 TRC CC4 channel is configured as input, IC4 is mapped on TRC 3 CC3S Capture/compare 3 selection 0 2 CC3S TI3 CC3 channel is configured as input, IC3 is mapped on TI3 1 TI4 CC3 channel is configured as input, IC3 is mapped on TI4 2 TRC CC3 channel is configured as input, IC3 is mapped on TRC 3 CCER CCER capture/compare enable register 0x20 0x10 read-write 0x00000000 4 0x4 1-4 CC%sNP Capture/Compare %s output Polarity 3 1 4 0x4 1-4 CC%sP Capture/Compare %s output Polarity 1 1 CC1P RisingEdge Noninverted/rising edge 0 FallingEdge Inverted/falling edge 1 4 0x4 1-4 CC%sE Capture/Compare %s output enable 0 1 CC1E Disabled Capture disabled 0 Enabled Capture enabled 1 CNT CNT counter 0x24 0x20 read-write 0x00000000 CNT Counter value 0 32 UIFCPY UIF copy This bit is a read-only copy of the UIF bit of the TIMx_ISR register. If the UIFREMAP bit in the TIMxCR1 is reset, bit 31 is reserved and read at 0 31 1 read-only CNT32 CNT32 32-bit counter register CNT 0x24 0x20 read-write 0x00000000 CNT counter value 0 32 read-write 0 4294967295 PSC PSC prescaler 0x28 0x10 read-write 0x00000000 PSC Prescaler value 0 16 0 65535 ARR ARR auto-reload register 0x2C 0x20 read-write 0x00000000 ARR Auto-reload value 0 32 0 4294967295 4 0x4 1-4 CCR%s CCR%s capture/compare register 0x34 0x20 read-write 0x00000000 CCR Capture/Compare value 0 32 0 4294967295 DCR DCR DMA control register 0x48 0x10 read-write 0x00000000 DBL DMA burst length 8 5 0 18 DBA DMA base address 0 5 0 31 DMAR DMAR DMA address for full transfer 0x4C 0x10 read-write 0x00000000 DMAB DMA register for burst accesses 0 16 OR OR1 TIM2 option register 1 0x50 0x20 read-write 0x00000000 ITR1_RMP Internal trigger 1 remap 10 2 TIM3 General purpose timers TIM 0x40000400 0x0 0x400 registers TIM3 TIM3 global interrupt 29 CR1 CR1 control register 1 0x0 0x10 read-write 0x00000000 CKD Clock division 8 2 CKD Div1 t_DTS = t_CK_INT 0 Div2 t_DTS = 2 × t_CK_INT 1 Div4 t_DTS = 4 × t_CK_INT 2 ARPE Auto-reload preload enable 7 1 ARPE Disabled TIMx_APRR register is not buffered 0 Enabled TIMx_APRR register is buffered 1 CMS Center-aligned mode selection 5 2 CMS EdgeAligned The counter counts up or down depending on the direction bit 0 CenterAligned1 The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting down. 1 CenterAligned2 The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting up. 2 CenterAligned3 The counter counts up and down alternatively. Output compare interrupt flags are set both when the counter is counting up or down. 3 DIR Direction 4 1 DIR Up Counter used as upcounter 0 Down Counter used as downcounter 1 OPM One-pulse mode 3 1 OPM Disabled Counter is not stopped at update event 0 Enabled Counter stops counting at the next update event (clearing the CEN bit) 1 URS Update request source 2 1 URS AnyEvent Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request 0 CounterOnly Only counter overflow/underflow generates an update interrupt or DMA request 1 UDIS Update disable 1 1 UDIS Enabled Update event enabled 0 Disabled Update event disabled 1 CEN Counter enable 0 1 CEN Disabled Counter disabled 0 Enabled Counter enabled 1 UIFREMAP UIF status bit remapping 11 1 CR2 CR2 control register 2 0x4 0x10 read-write 0x00000000 TI1S TI1 selection 7 1 TI1S Normal The TIMx_CH1 pin is connected to TI1 input 0 XOR The TIMx_CH1, CH2, CH3 pins are connected to TI1 input 1 MMS Master mode selection 4 3 MMS Reset The UG bit from the TIMx_EGR register is used as trigger output 0 Enable The counter enable signal, CNT_EN, is used as trigger output 1 Update The update event is selected as trigger output 2 ComparePulse The trigger output send a positive pulse when the CC1IF flag it to be set, as soon as a capture or a compare match occurred 3 CompareOC1 OC1REF signal is used as trigger output 4 CompareOC2 OC2REF signal is used as trigger output 5 CompareOC3 OC3REF signal is used as trigger output 6 CompareOC4 OC4REF signal is used as trigger output 7 CCDS Capture/compare DMA selection 3 1 CCDS OnCompare CCx DMA request sent when CCx event occurs 0 OnUpdate CCx DMA request sent when update event occurs 1 SMCR SMCR slave mode control register 0x8 0x20 read-write 0x00000000 SMS Slave mode selection 0 3 SMS Disabled Slave mode disabled - if CEN = ‘1 then the prescaler is clocked directly by the internal clock. 0 Encoder_Mode_1 Encoder mode 1 - Counter counts up/down on TI2FP1 edge depending on TI1FP2 level. 1 Encoder_Mode_2 Encoder mode 2 - Counter counts up/down on TI1FP2 edge depending on TI2FP1 level. 2 Encoder_Mode_3 Encoder mode 3 - Counter counts up/down on both TI1FP1 and TI2FP2 edges depending on the level of the other input. 3 Reset_Mode Reset Mode - Rising edge of the selected trigger input (TRGI) reinitializes the counter and generates an update of the registers. 4 Gated_Mode Gated Mode - The counter clock is enabled when the trigger input (TRGI) is high. The counter stops (but is not reset) as soon as the trigger becomes low. Both start and stop of the counter are controlled. 5 Trigger_Mode Trigger Mode - The counter starts at a rising edge of the trigger TRGI (but it is not reset). Only the start of the counter is controlled. 6 Ext_Clock_Mode External Clock Mode 1 - Rising edges of the selected trigger (TRGI) clock the counter. 7 TS Trigger selection 4 3 TS ITR0 Internal Trigger 0 (ITR0) 0 ITR1 Internal Trigger 1 (ITR1) 1 ITR2 Internal Trigger 2 (ITR2) 2 TI1F_ED TI1 Edge Detector (TI1F_ED) 4 TI1FP1 Filtered Timer Input 1 (TI1FP1) 5 TI2FP2 Filtered Timer Input 2 (TI2FP2) 6 ETRF External Trigger input (ETRF) 7 MSM Master/Slave mode 7 1 MSM NoSync No action 0 Sync The effect of an event on the trigger input (TRGI) is delayed to allow a perfect synchronization between the current timer and its slaves (through TRGO). It is useful if we want to synchronize several timers on a single external event. 1 ETF External trigger filter 8 4 ETF NoFilter No filter, sampling is done at fDTS 0 FCK_INT_N2 fSAMPLING=fCK_INT, N=2 1 FCK_INT_N4 fSAMPLING=fCK_INT, N=4 2 FCK_INT_N8 fSAMPLING=fCK_INT, N=8 3 FDTS_Div2_N6 fSAMPLING=fDTS/2, N=6 4 FDTS_Div2_N8 fSAMPLING=fDTS/2, N=8 5 FDTS_Div4_N6 fSAMPLING=fDTS/4, N=6 6 FDTS_Div4_N8 fSAMPLING=fDTS/4, N=8 7 FDTS_Div8_N6 fSAMPLING=fDTS/8, N=6 8 FDTS_Div8_N8 fSAMPLING=fDTS/8, N=8 9 FDTS_Div16_N5 fSAMPLING=fDTS/16, N=5 10 FDTS_Div16_N6 fSAMPLING=fDTS/16, N=6 11 FDTS_Div16_N8 fSAMPLING=fDTS/16, N=8 12 FDTS_Div32_N5 fSAMPLING=fDTS/32, N=5 13 FDTS_Div32_N6 fSAMPLING=fDTS/32, N=6 14 FDTS_Div32_N8 fSAMPLING=fDTS/32, N=8 15 ETPS External trigger prescaler 12 2 ETPS Div1 Prescaler OFF 0 Div2 ETRP frequency divided by 2 1 Div4 ETRP frequency divided by 4 2 Div8 ETRP frequency divided by 8 3 ECE External clock enable 14 1 ECE Disabled External clock mode 2 disabled 0 Enabled External clock mode 2 enabled. The counter is clocked by any active edge on the ETRF signal. 1 ETP External trigger polarity 15 1 ETP NotInverted ETR is noninverted, active at high level or rising edge 0 Inverted ETR is inverted, active at low level or falling edge 1 SMS_3 Slave model selection - bit[3] 16 1 DIER DIER DMA/Interrupt enable register 0xC 0x10 read-write 0x00000000 TDE Trigger DMA request enable 14 1 TDE Disabled Trigger DMA request disabled 0 Enabled Trigger DMA request enabled 1 4 0x1 1-4 CC%sDE Capture/Compare %s DMA request enable 9 1 CC1DE Disabled CCx DMA request disabled 0 Enabled CCx DMA request enabled 1 UDE Update DMA request enable 8 1 UDE Disabled Update DMA request disabled 0 Enabled Update DMA request enabled 1 TIE Trigger interrupt enable 6 1 TIE Disabled Trigger interrupt disabled 0 Enabled Trigger interrupt enabled 1 4 0x1 1-4 CC%sIE Capture/Compare %s interrupt enable 1 1 CC1IE Disabled CCx interrupt disabled 0 Enabled CCx interrupt enabled 1 UIE Update interrupt enable 0 1 UIE Disabled Update interrupt disabled 0 Enabled Update interrupt enabled 1 SR SR status register 0x10 0x10 read-write 0x00000000 4 0x1 1-4 CC%sOF Capture/Compare %s overcapture flag 9 1 zeroToClear CC1OFR read NoOvercapture No overcapture has been detected 0 Overcapture The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set 1 CC1OFW write Clear Clear flag 0 TIF Trigger interrupt flag 6 1 zeroToClear TIFR read NoTrigger No trigger event occurred 0 Trigger Trigger interrupt pending 1 TIFW write Clear Clear flag 0 4 0x1 1-4 CC%sIF Capture/compare %s interrupt flag 1 1 zeroToClear CC1IFR read NoMatch No campture/compare has been detected 0 Match If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register. 1 CC1IFW write Clear Clear flag 0 UIF Update interrupt flag 0 1 zeroToClear UIFR read NoUpdateOccurred No update occurred 0 UpdatePending Update interrupt pending 1 UIFW write Clear Clear flag 0 EGR EGR event generation register 0x14 0x10 write-only 0x00000000 TG Trigger generation 6 1 TGW Trigger The TIF flag is set in TIMx_SR register. Related interrupt or DMA transfer can occur if enabled. 1 4 0x1 1-4 CC%sG Capture/compare %s generation 1 1 CC1GW Trigger If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register. 1 UG Update generation 0 1 UG Update Re-initializes the timer counter and generates an update of the registers. 1 CCMR1_Output CCMR1_Output capture/compare mode register 1 (output mode) 0x18 0x20 read-write 0x00000000 2 0x8 1-2 OC%sCE Output compare %s clear enable 7 1 OC1CE Disabled OCxRef is not affected by the ETRF signal 0 Enabled OCxRef is cleared as soon as a High level is detected on ETRF signal 1 2 0x8 1-2 OC%sM Output compare %s mode 4 3 OC1M Frozen The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive 0 ActiveOnMatch Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1 1 InactiveOnMatch Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved 2 Toggle OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved 3 ForceInactive OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF 4 ForceActive OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF 5 PwmMode1 In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down 6 PwmMode2 Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1 7 2 0x8 1-2 OC%sPE Output compare %s preload enable 3 1 OC1PE Disabled Preload register on CCRx disabled. New values written to CCRx are taken into account immediately 0 Enabled Preload register on CCRx enabled. Preload value is loaded into active register on each update event 1 2 0x8 1-2 OC%sFE Output compare %s fast enable 2 1 OC1FE Disabled Fast output disabled 0 Enabled Fast output enabled 1 2 0x8 1-2 CC%sS Capture/Compare %s selection 0 2 CC1S Output CCx channel is configured as output 0 2 0x8 1-2 OC%sM_3 Output compare %s mode, bit 3 16 1 OC1M_3 Normal Normal output compare mode (modes 0-7) 0 Extended Extended output compare mode (modes 7-15) 1 CCMR1_Input CCMR1_Input capture/compare mode register 1 (input mode) CCMR1_Output 0x18 0x20 read-write 0x00000000 2 0x8 1-2 IC%sF Input capture %s filter 4 4 ICFilter NoFilter No filter, sampling is done at fDTS 0 FCK_INT_N2 fSAMPLING=fCK_INT, N=2 1 FCK_INT_N4 fSAMPLING=fCK_INT, N=4 2 FCK_INT_N8 fSAMPLING=fCK_INT, N=8 3 FDTS_Div2_N6 fSAMPLING=fDTS/2, N=6 4 FDTS_Div2_N8 fSAMPLING=fDTS/2, N=8 5 FDTS_Div4_N6 fSAMPLING=fDTS/4, N=6 6 FDTS_Div4_N8 fSAMPLING=fDTS/4, N=8 7 FDTS_Div8_N6 fSAMPLING=fDTS/8, N=6 8 FDTS_Div8_N8 fSAMPLING=fDTS/8, N=8 9 FDTS_Div16_N5 fSAMPLING=fDTS/16, N=5 10 FDTS_Div16_N6 fSAMPLING=fDTS/16, N=6 11 FDTS_Div16_N8 fSAMPLING=fDTS/16, N=8 12 FDTS_Div32_N5 fSAMPLING=fDTS/32, N=5 13 FDTS_Div32_N6 fSAMPLING=fDTS/32, N=6 14 FDTS_Div32_N8 fSAMPLING=fDTS/32, N=8 15 2 0x8 1-2 IC%sPSC Input capture %s prescaler 2 2 ICPrescaler NoPrescaler No prescaler, capture is done each time an edge is detected on the capture input 0 TwoEvents Capture is done once every 2 events 1 FourEvents Capture is done once every 4 events 2 EightEvents Capture is done once every 8 events 3 CC2S Capture/Compare 2 selection 8 2 CC2S TI2 CC2 channel is configured as input, IC2 is mapped on TI2 1 TI1 CC2 channel is configured as input, IC2 is mapped on TI1 2 TRC CC2 channel is configured as input, IC2 is mapped on TRC 3 CC1S Capture/Compare 1 selection 0 2 CC1S TI1 CC1 channel is configured as input, IC1 is mapped on TI1 1 TI2 CC1 channel is configured as input, IC1 is mapped on TI2 2 TRC CC1 channel is configured as input, IC1 is mapped on TRC 3 CCMR2_Output CCMR2_Output capture/compare mode register 2 (output mode) 0x1C 0x20 read-write 0x00000000 2 0x8 3-4 OC%sCE Output compare %s clear enable 7 1 2 0x8 3-4 OC%sM Output compare %s mode 4 3 2 0x8 3-4 OC%sPE Output compare %s preload enable 3 1 2 0x8 3-4 OC%sFE Output compare %s fast enable 2 1 2 0x8 3-4 CC%sS Capture/Compare %s selection 0 2 2 0x8 3-4 OC%sM_3 Output compare %s mode, bit 3 16 1 CCMR2_Input CCMR2_Input capture/compare mode register 2 (input mode) CCMR2_Output 0x1C 0x20 read-write 0x00000000 2 0x8 3-4 IC%sF Input capture %s filter 4 4 2 0x8 3-4 IC%sPSC Input capture %s prescaler 2 2 CC4S Capture/Compare 4 selection 8 2 CC4S TI4 CC4 channel is configured as input, IC4 is mapped on TI4 1 TI3 CC4 channel is configured as input, IC4 is mapped on TI3 2 TRC CC4 channel is configured as input, IC4 is mapped on TRC 3 CC3S Capture/compare 3 selection 0 2 CC3S TI3 CC3 channel is configured as input, IC3 is mapped on TI3 1 TI4 CC3 channel is configured as input, IC3 is mapped on TI4 2 TRC CC3 channel is configured as input, IC3 is mapped on TRC 3 CCER CCER capture/compare enable register 0x20 0x10 read-write 0x00000000 4 0x4 1-4 CC%sNP Capture/Compare %s output Polarity 3 1 4 0x4 1-4 CC%sP Capture/Compare %s output Polarity 1 1 CC1P RisingEdge Noninverted/rising edge 0 FallingEdge Inverted/falling edge 1 4 0x4 1-4 CC%sE Capture/Compare %s output enable 0 1 CC1E Disabled Capture disabled 0 Enabled Capture enabled 1 CNT CNT counter 0x24 0x20 read-write 0x00000000 CNT Counter value 0 16 0 65535 UIFCPY UIF copy This bit is a read-only copy of the UIF bit of the TIMx_ISR register. If the UIFREMAP bit in the TIMxCR1 is reset, bit 31 is reserved and read at 0 31 1 read-only CNT16 CNT16 16-bit counter register CNT 0x24 0x10 read-write 0x00000000 CNT counter value 0 16 read-write 0 65535 PSC PSC prescaler 0x28 0x10 read-write 0x00000000 PSC Prescaler value 0 16 0 65535 ARR ARR auto-reload register 0x2C 0x10 read-write 0x0000FFFF ARR Auto-reload value 0 16 0 65535 4 0x4 1-4 CCR%s CCR%s capture/compare register 0x34 0x10 read-write 0x00000000 CCR Capture/Compare value 0 16 0 65535 DCR DCR DMA control register 0x48 0x10 read-write 0x00000000 DBL DMA burst length 8 5 0 18 DBA DMA base address 0 5 0 31 DMAR DMAR DMA address for full transfer 0x4C 0x10 read-write 0x00000000 DMAB DMA register for burst accesses 0 16 TIM4 General purpose timers TIM 0x40000800 TIM4 TIM4 global interrupt 30 TIM5 General purpose timers TIM 0x40000C00 0x0 0x400 registers TIM5 TIM5 global interrupt 50 CR1 CR1 control register 1 0x0 CR2 CR2 control register 2 0x4 SMCR SMCR slave mode control register 0x8 0x20 read-write 0x00000000 SMS Slave mode selection 0 3 TS Trigger selection 4 3 TS ITR0 Internal Trigger 0 (ITR0) 0 ITR1 Internal Trigger 1 (ITR1) 1 ITR2 Internal Trigger 2 (ITR2) 2 TI1F_ED TI1 Edge Detector (TI1F_ED) 4 TI1FP1 Filtered Timer Input 1 (TI1FP1) 5 TI2FP2 Filtered Timer Input 2 (TI2FP2) 6 ETRF External Trigger input (ETRF) 7 MSM Master/Slave mode 7 1 ETF External trigger filter 8 4 ETPS External trigger prescaler 12 2 ECE External clock enable 14 1 ETP External trigger polarity 15 1 SMS_3 Slave model selection - bit[3] 16 1 DIER DIER DMA/Interrupt enable register 0xC SR SR status register 0x10 EGR EGR event generation register 0x14 CCMR1_Output CCMR1_Output capture/compare mode register 1 (output mode) 0x18 CCMR1_Input CCMR1_Input capture/compare mode register 1 (input mode) CCMR1_Output 0x18 CCMR2_Output CCMR2_Output capture/compare mode register 2 (output mode) 0x1C CCMR2_Input CCMR2_Input capture/compare mode register 2 (input mode) CCMR2_Output 0x1C CCER CCER capture/compare enable register 0x20 CNT CNT counter 0x24 CNT32 CNT32 32-bit counter register CNT 0x24 0x20 read-write 0x00000000 CNT counter value 0 32 read-write 0 4294967295 PSC PSC prescaler 0x28 ARR ARR auto-reload register 0x2C 4 0x4 1-4 CCR%s CCR%s capture/compare register 0x34 DCR DCR DMA control register 0x48 DMAR DMAR DMA address for full transfer 0x4C OR OR1 TIM2 option register 1 0x50 0x20 read-write 0x00000000 TI4_RMP Input Capture 4 remap 6 2 TIM9 General purpose timers TIM 0x40014000 0x0 0x400 registers CR1 CR1 control register 1 0x0 0x10 read-write 0x00000000 CKD Clock division 8 2 CKD Div1 t_DTS = t_CK_INT 0 Div2 t_DTS = 2 × t_CK_INT 1 Div4 t_DTS = 4 × t_CK_INT 2 ARPE Auto-reload preload enable 7 1 ARPE Disabled TIMx_APRR register is not buffered 0 Enabled TIMx_APRR register is buffered 1 OPM One-pulse mode 3 1 OPM Disabled Counter is not stopped at update event 0 Enabled Counter stops counting at the next update event (clearing the CEN bit) 1 URS Update request source 2 1 URS AnyEvent Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request 0 CounterOnly Only counter overflow/underflow generates an update interrupt or DMA request 1 UDIS Update disable 1 1 UDIS Enabled Update event enabled 0 Disabled Update event disabled 1 CEN Counter enable 0 1 CEN Disabled Counter disabled 0 Enabled Counter enabled 1 UIFREMAP UIF status bit remapping 11 1 SMCR SMCR slave mode control register 0x8 0x20 read-write 0x00000000 MSM Master/Slave mode 7 1 TS Trigger selection 4 3 SMS Slave mode selection 0 3 SMS_3 Slave mode selection - bit 3 16 1 DIER DIER DMA/Interrupt enable register 0xC 0x10 read-write 0x00000000 TIE Trigger interrupt enable 6 1 TIE Disabled Trigger interrupt disabled 0 Enabled Trigger interrupt enabled 1 2 0x1 1-2 CC%sIE Capture/Compare %s interrupt enable 1 1 CC1IE Disabled CCx interrupt disabled 0 Enabled CCx interrupt enabled 1 UIE Update interrupt enable 0 1 UIE Disabled Update interrupt disabled 0 Enabled Update interrupt enabled 1 SR SR status register 0x10 0x10 read-write 0x00000000 2 0x1 1-2 CC%sOF Capture/Compare %s overcapture flag 9 1 zeroToClear CC1OFR read NoOvercapture No overcapture has been detected 0 Overcapture The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set 1 CC1OFW write Clear Clear flag 0 TIF Trigger interrupt flag 6 1 zeroToClear TIFR read NoTrigger No trigger event occurred 0 Trigger Trigger interrupt pending 1 TIFW write Clear Clear flag 0 2 0x1 1-2 CC%sIF Capture/compare %s interrupt flag 1 1 zeroToClear CC1IFR read NoMatch No campture/compare has been detected 0 Match If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register. 1 CC1IFW write Clear Clear flag 0 UIF Update interrupt flag 0 1 zeroToClear UIFR read NoUpdateOccurred No update occurred 0 UpdatePending Update interrupt pending 1 UIFW write Clear Clear flag 0 EGR EGR event generation register 0x14 0x10 write-only 0x00000000 TG Trigger generation 6 1 TGW Trigger The TIF flag is set in TIMx_SR register. Related interrupt or DMA transfer can occur if enabled. 1 2 0x1 1-2 CC%sG Capture/compare %s generation 1 1 CC1GW Trigger If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register. 1 UG Update generation 0 1 UG Update Re-initializes the timer counter and generates an update of the registers. 1 CCMR1_Output CCMR1_Output capture/compare mode register 1 (output mode) 0x18 0x20 read-write 0x00000000 2 0x8 1-2 OC%sM Output compare %s mode 4 3 OC1M Frozen The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive 0 ActiveOnMatch Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1 1 InactiveOnMatch Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved 2 Toggle OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved 3 ForceInactive OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF 4 ForceActive OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF 5 PwmMode1 In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / Reserved 6 PwmMode2 Inversely to PwmMode1 / Reserved 7 2 0x8 1-2 OC%sPE Output compare %s preload enable 3 1 OC1PE Disabled Preload register on CCRx disabled. New values written to CCRx are taken into account immediately 0 Enabled Preload register on CCRx enabled. Preload value is loaded into active register on each update event 1 2 0x8 1-2 OC%sFE Output compare %s fast enable 2 1 OC1FE Disabled Fast output disabled 0 Enabled Fast output enabled 1 2 0x8 1-2 CC%sS Capture/Compare %s selection 0 2 CC1S Output CCx channel is configured as output 0 2 0x8 1-2 OC%sM_3 Output compare %s mode, bit 3 16 1 OC1M_3 Normal Normal output compare mode (modes 0-7) 0 Extended Extended output compare mode (modes 7-15) 1 CCMR1_Input CCMR1_Input capture/compare mode register 1 (input mode) CCMR1_Output 0x18 0x20 read-write 0x00000000 2 0x8 1-2 IC%sF Input capture %s filter 4 4 ICFilter NoFilter No filter, sampling is done at fDTS 0 FCK_INT_N2 fSAMPLING=fCK_INT, N=2 1 FCK_INT_N4 fSAMPLING=fCK_INT, N=4 2 FCK_INT_N8 fSAMPLING=fCK_INT, N=8 3 FDTS_Div2_N6 fSAMPLING=fDTS/2, N=6 4 FDTS_Div2_N8 fSAMPLING=fDTS/2, N=8 5 FDTS_Div4_N6 fSAMPLING=fDTS/4, N=6 6 FDTS_Div4_N8 fSAMPLING=fDTS/4, N=8 7 FDTS_Div8_N6 fSAMPLING=fDTS/8, N=6 8 FDTS_Div8_N8 fSAMPLING=fDTS/8, N=8 9 FDTS_Div16_N5 fSAMPLING=fDTS/16, N=5 10 FDTS_Div16_N6 fSAMPLING=fDTS/16, N=6 11 FDTS_Div16_N8 fSAMPLING=fDTS/16, N=8 12 FDTS_Div32_N5 fSAMPLING=fDTS/32, N=5 13 FDTS_Div32_N6 fSAMPLING=fDTS/32, N=6 14 FDTS_Div32_N8 fSAMPLING=fDTS/32, N=8 15 2 0x8 1-2 IC%sPSC Input capture %s prescaler 2 2 ICPrescaler NoPrescaler No prescaler, capture is done each time an edge is detected on the capture input 0 TwoEvents Capture is done once every 2 events 1 FourEvents Capture is done once every 4 events 2 EightEvents Capture is done once every 8 events 3 CC2S Capture/Compare 2 selection 8 2 CC2S TI2 CC2 channel is configured as input, IC2 is mapped on TI2 1 TI1 CC2 channel is configured as input, IC2 is mapped on TI1 2 TRC CC2 channel is configured as input, IC2 is mapped on TRC 3 CC1S Capture/Compare 1 selection 0 2 CC1S TI1 CC1 channel is configured as input, IC1 is mapped on TI1 1 TI2 CC1 channel is configured as input, IC1 is mapped on TI2 2 TRC CC1 channel is configured as input, IC1 is mapped on TRC 3 CCER CCER capture/compare enable register 0x20 0x10 read-write 0x00000000 2 0x4 1-2 CC%sNP Capture/Compare %s output Polarity 3 1 2 0x4 1-2 CC%sP Capture/Compare %s output Polarity 1 1 CC1P RisingEdge Noninverted/rising edge 0 FallingEdge Inverted/falling edge 1 2 0x4 1-2 CC%sE Capture/Compare %s output enable 0 1 CC1E Disabled Capture disabled 0 Enabled Capture enabled 1 CNT CNT counter 0x24 0x20 read-write 0x00000000 CNT counter value 0 16 0 65535 UIFCPY UIF copy This bit is a read-only copy of the UIF bit of the TIMx_ISR register. If the UIFREMAP bit in the TIMxCR1 is reset, bit 31 is reserved and read at 0 31 1 read-only CNT16 CNT16 16-bit counter register CNT 0x24 0x10 read-write 0x00000000 CNT counter value 0 16 read-write 0 65535 PSC PSC prescaler 0x28 0x10 read-write 0x00000000 PSC Prescaler value 0 16 0 65535 ARR ARR auto-reload register 0x2C 0x10 read-write 0x0000FFFF ARR Auto-reload value 0 16 0 65535 2 0x4 1-2 CCR%s CCR%s capture/compare register 0x34 0x10 read-write 0x00000000 CCR Capture/Compare value 0 16 0 65535 TIM12 TIM 0x40001800 TIM10 General-purpose-timers TIM 0x40014400 0x0 0x400 registers CR1 CR1 control register 1 0x0 0x10 read-write 0x00000000 CKD Clock division 8 2 CKD Div1 t_DTS = t_CK_INT 0 Div2 t_DTS = 2 × t_CK_INT 1 Div4 t_DTS = 4 × t_CK_INT 2 ARPE Auto-reload preload enable 7 1 ARPE Disabled TIMx_APRR register is not buffered 0 Enabled TIMx_APRR register is buffered 1 URS Update request source 2 1 URS AnyEvent Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request 0 CounterOnly Only counter overflow/underflow generates an update interrupt or DMA request 1 UDIS Update disable 1 1 UDIS Enabled Update event enabled 0 Disabled Update event disabled 1 CEN Counter enable 0 1 CEN Disabled Counter disabled 0 Enabled Counter enabled 1 OPM One-pulse mode 3 1 read-write OPM Disabled Counter is not stopped at update event 0 Enabled Counter stops counting at the next update event (clearing the CEN bit) 1 UIFREMAP UIF status bit remapping 11 1 DIER DIER DMA/Interrupt enable register 0xC 0x10 read-write 0x00000000 1 0x0 1-1 CC%sIE Capture/Compare %s interrupt enable 1 1 CC1IE Disabled CCx interrupt disabled 0 Enabled CCx interrupt enabled 1 UIE Update interrupt enable 0 1 UIE Disabled Update interrupt disabled 0 Enabled Update interrupt enabled 1 SR SR status register 0x10 0x10 read-write 0x00000000 1 0x0 1-1 CC%sOF Capture/Compare %s overcapture flag 9 1 zeroToClear CC1OFR read NoOvercapture No overcapture has been detected 0 Overcapture The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set 1 CC1OFW write Clear Clear flag 0 1 0x0 1-1 CC%sIF Capture/compare %s interrupt flag 1 1 zeroToClear CC1IFR read NoMatch No campture/compare has been detected 0 Match If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register. 1 CC1IFW write Clear Clear flag 0 UIF Update interrupt flag 0 1 zeroToClear UIFR read NoUpdateOccurred No update occurred 0 UpdatePending Update interrupt pending 1 UIFW write Clear Clear flag 0 EGR EGR event generation register 0x14 0x10 write-only 0x00000000 1 0x0 1-1 CC%sG Capture/compare %s generation 1 1 CC1GW Trigger If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register. 1 UG Update generation 0 1 UG Update Re-initializes the timer counter and generates an update of the registers. 1 CCMR1_Output CCMR1_Output capture/compare mode register 1 (output mode) 0x18 0x20 read-write 0x00000000 1 0x0 1-1 OC%sM Output compare %s mode 4 3 OC1M Frozen The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs 0 ActiveOnMatch Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register 1 InactiveOnMatch Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register 2 Toggle OCyREF toggles when TIMx_CNT=TIMx_CCRy 3 ForceInactive OCyREF is forced low 4 ForceActive OCyREF is forced high 5 PwmMode1 In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active 6 PwmMode2 Inversely to PwmMode1 7 1 0x0 1-1 OC%sPE Output compare %s preload enable 3 1 OC1PE Disabled Preload register on CCRx disabled. New values written to CCRx are taken into account immediately 0 Enabled Preload register on CCRx enabled. Preload value is loaded into active register on each update event 1 1 0x0 1-1 OC%sFE Output compare %s fast enable 2 1 OC1FE Disabled Fast output disabled 0 Enabled Fast output enabled 1 1 0x0 1-1 CC%sS Capture/Compare %s selection 0 2 CC1S Output CCx channel is configured as output 0 1 0x0 1-1 OC%sM_3 Output compare %s mode, bit 3 16 1 CCMR1_Input CCMR1_Input capture/compare mode register 1 (input mode) CCMR1_Output 0x18 0x20 read-write 0x00000000 1 0x0 1-1 IC%sF Input capture %s filter 4 4 ICFilter NoFilter No filter, sampling is done at fDTS 0 FCK_INT_N2 fSAMPLING=fCK_INT, N=2 1 FCK_INT_N4 fSAMPLING=fCK_INT, N=4 2 FCK_INT_N8 fSAMPLING=fCK_INT, N=8 3 FDTS_Div2_N6 fSAMPLING=fDTS/2, N=6 4 FDTS_Div2_N8 fSAMPLING=fDTS/2, N=8 5 FDTS_Div4_N6 fSAMPLING=fDTS/4, N=6 6 FDTS_Div4_N8 fSAMPLING=fDTS/4, N=8 7 FDTS_Div8_N6 fSAMPLING=fDTS/8, N=6 8 FDTS_Div8_N8 fSAMPLING=fDTS/8, N=8 9 FDTS_Div16_N5 fSAMPLING=fDTS/16, N=5 10 FDTS_Div16_N6 fSAMPLING=fDTS/16, N=6 11 FDTS_Div16_N8 fSAMPLING=fDTS/16, N=8 12 FDTS_Div32_N5 fSAMPLING=fDTS/32, N=5 13 FDTS_Div32_N6 fSAMPLING=fDTS/32, N=6 14 FDTS_Div32_N8 fSAMPLING=fDTS/32, N=8 15 1 0x0 1-1 IC%sPSC Input capture %s prescaler 2 2 ICPrescaler NoPrescaler No prescaler, capture is done each time an edge is detected on the capture input 0 TwoEvents Capture is done once every 2 events 1 FourEvents Capture is done once every 4 events 2 EightEvents Capture is done once every 8 events 3 CC1S Capture/Compare 1 selection 0 2 CC1S TI1 CC1 channel is configured as input, IC1 is mapped on TI1 1 CCER CCER capture/compare enable register 0x20 0x10 read-write 0x00000000 1 0x0 1-1 CC%sNP Capture/Compare %s output Polarity 3 1 1 0x0 1-1 CC%sP Capture/Compare %s output Polarity 1 1 CC1P RisingEdge Noninverted/rising edge 0 FallingEdge Inverted/falling edge 1 1 0x0 1-1 CC%sE Capture/Compare %s output enable 0 1 CC1E Disabled Capture disabled 0 Enabled Capture enabled 1 CNT CNT counter 0x24 0x20 read-write 0x00000000 CNT counter value 0 16 0 65535 UIFCPY UIF copy This bit is a read-only copy of the UIF bit of the TIMx_ISR register. If the UIFREMAP bit in the TIMxCR1 is reset, bit 31 is reserved and read at 0 31 1 read-only CNT16 CNT16 16-bit counter register CNT 0x24 0x10 read-write 0x00000000 CNT counter value 0 16 read-write 0 65535 PSC PSC prescaler 0x28 0x10 read-write 0x00000000 PSC Prescaler value 0 16 0 65535 ARR ARR auto-reload register 0x2C 0x10 read-write 0x0000FFFF ARR Auto-reload value 0 16 0 65535 1 0x2 1-1 CCR%s CCR%s capture/compare register 0x34 0x10 read-write 0x00000000 CCR Capture/Compare value 0 16 0 65535 OR OR option register 0x50 0x20 read-write 0x00000000 TI1_RMP TIM11 Input 1 remapping capability 0 2 TIM11 TIM 0x40014800 TIM13 TIM 0x40001C00 TIM14 TIM 0x40002000 TIM6 Basic timers TIM 0x40001000 0x0 0x400 registers TIM6_DAC TIM6 global interrupt, DAC1 and DAC2 underrun error interrupt 54 CR1 CR1 control register 1 0x0 0x10 read-write 0x00000000 ARPE Auto-reload preload enable 7 1 ARPE Disabled TIMx_APRR register is not buffered 0 Enabled TIMx_APRR register is buffered 1 OPM One-pulse mode 3 1 OPM Disabled Counter is not stopped at update event 0 Enabled Counter stops counting at the next update event (clearing the CEN bit) 1 URS Update request source 2 1 URS AnyEvent Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request 0 CounterOnly Only counter overflow/underflow generates an update interrupt or DMA request 1 UDIS Update disable 1 1 UDIS Enabled Update event enabled 0 Disabled Update event disabled 1 CEN Counter enable 0 1 CEN Disabled Counter disabled 0 Enabled Counter enabled 1 UIFREMAP UIF status bit remapping 11 1 CR2 CR2 control register 2 0x4 0x10 read-write 0x00000000 MMS Master mode selection 4 3 MMS Reset Use UG bit from TIMx_EGR register 0 Enable Use CNT bit from TIMx_CEN register 1 Update Use the update event 2 DIER DIER DMA/Interrupt enable register 0xC 0x10 read-write 0x00000000 UDE Update DMA request enable 8 1 UDE Disabled Update DMA request disabled 0 Enabled Update DMA request enabled 1 UIE Update interrupt enable 0 1 UIE Disabled Update interrupt disabled 0 Enabled Update interrupt enabled 1 SR SR status register 0x10 0x10 read-write 0x00000000 UIF Update interrupt flag 0 1 zeroToClear UIFR read NoUpdateOccurred No update occurred 0 UpdatePending Update interrupt pending 1 UIFW write Clear Clear flag 0 EGR EGR event generation register 0x14 0x20 write-only 0x00000000 UG Update generation 0 1 UG Update Re-initializes the timer counter and generates an update of the registers. 1 CNT CNT counter 0x24 0x20 read-write 0x00000000 CNT Low counter value 0 16 0 65535 UIFCPY UIF copy This bit is a read-only copy of the UIF bit of the TIMx_ISR register. If the UIFREMAP bit in the TIMxCR1 is reset, bit 31 is reserved and read at 0 31 1 read-only CNT16 CNT16 16-bit counter register CNT 0x24 0x10 read-write 0x00000000 CNT counter value 0 16 read-write PSC PSC prescaler 0x28 0x10 read-write 0x00000000 PSC Prescaler value 0 16 0 65535 ARR ARR auto-reload register 0x2C 0x10 read-write 0x0000FFFF ARR Low Auto-reload value 0 16 0 65535 TIM7 TIM 0x40001400 TIM7 TIM7 global interrupt 55 Ethernet_MAC Ethernet: media access control (MAC) Ethernet 0x40028000 0x0 0x100 registers MACCR MACCR Ethernet MAC configuration register 0x0 0x20 read-write 0x00008000 RE Receiver enable 2 1 RE Disabled MAC receive state machine is disabled after the completion of the reception of the current frame 0 Enabled MAC receive state machine is enabled 1 TE Transmitter enable 3 1 TE Disabled MAC transmit state machine is disabled after completion of the transmission of the current frame 0 Enabled MAC transmit state machine is enabled 1 DC Deferral check 4 1 DC Disabled MAC defers until CRS signal goes inactive 0 Enabled Deferral check function enabled 1 BL Back-off limit 5 2 BL BL10 For retransmission n, wait up to 2^min(n, 10) time slots 0 BL8 For retransmission n, wait up to 2^min(n, 8) time slots 1 BL4 For retransmission n, wait up to 2^min(n, 4) time slots 2 BL1 For retransmission n, wait up to 2^min(n, 1) time slots 3 APCS Automatic pad/CRC stripping 7 1 APCS Disabled MAC passes all incoming frames unmodified 0 Strip MAC strips the Pad/FCS field on incoming frames only for lengths less than or equal to 1500 bytes 1 RD Retry disable 9 1 RD Enabled MAC attempts retries based on the settings of BL 0 Disabled MAC attempts only 1 transmission 1 IPCO IPv4 checksum offload 10 1 IPCO Disabled IPv4 checksum offload disabled 0 Offload IPv4 checksums are checked in received frames 1 DM Duplex mode 11 1 DM HalfDuplex MAC operates in half-duplex mode 0 FullDuplex MAC operates in full-duplex mode 1 LM Loopback mode 12 1 LM Normal Normal mode 0 Loopback MAC operates in loopback mode at the MII 1 ROD Receive own disable 13 1 ROD Enabled MAC receives all packets from PHY while transmitting 0 Disabled MAC disables reception of frames in half-duplex mode 1 FES Fast Ethernet speed 14 1 FES FES10 10 Mbit/s 0 FES100 100 Mbit/s 1 CSD Carrier sense disable 16 1 CSD Enabled Errors generated due to loss of carrier 0 Disabled No error generated due to loss of carrier 1 IFG Interframe gap 17 3 IFG IFG96 96 bit times 0 IFG88 88 bit times 1 IFG80 80 bit times 2 IFG72 72 bit times 3 IFG64 64 bit times 4 IFG56 56 bit times 5 IFG48 48 bit times 6 IFG40 40 bit times 7 JD Jabber disable 22 1 JD Enabled Jabber enabled, transmit frames up to 2048 bytes 0 Disabled Jabber disabled, transmit frames up to 16384 bytes 1 WD Watchdog disable 23 1 WD Enabled Watchdog enabled, receive frames limited to 2048 bytes 0 Disabled Watchdog disabled, receive frames may be up to to 16384 bytes 1 CSTF CRC stripping for type frames 25 1 CSTF Disabled CRC not stripped 0 Enabled CRC stripped 1 MACFFR MACFFR Ethernet MAC frame filter register 0x4 0x20 read-write 0x00000000 PM Promiscuous mode 0 1 PM Disabled Normal address filtering 0 Enabled Address filters pass all incoming frames regardless of their destination or source address 1 HU Hash unicast 1 1 HU Perfect MAC performs a perfect destination address filtering for unicast frames 0 Hash MAC performs destination address filtering of received unicast frames according to the hash table 1 HM Hash multicast 2 1 HM Perfect MAC performs a perfect destination address filtering for multicast frames 0 Hash MAC performs destination address filtering of received multicast frames according to the hash table 1 DAIF Destination address unique filtering 3 1 DAIF Normal Normal filtering of frames 0 Invert Address check block operates in inverse filtering mode for the DA address comparison 1 PAM Pass all multicast 4 1 PAM Disabled Filtering of multicast frames depends on HM 0 Enabled All received frames with a multicast destination address are passed 1 BFD Broadcast frames disable 5 1 BFD Enabled Address filters pass all received broadcast frames 0 Disabled Address filters filter all incoming broadcast frames 1 PCF Pass control frames 6 2 PCF PreventAll MAC prevents all control frames from reaching the application 0 ForwardAllExceptPause MAC forwards all control frames to application except Pause 1 ForwardAll MAC forwards all control frames to application even if they fail the address filter 2 ForwardAllFiltered MAC forwards control frames that pass the address filter 3 SAIF Source address inverse filtering 8 1 SAIF Normal Source address filter operates normally 0 Invert Source address filter operation inverted 1 SAF Source address filter 9 1 SAF Disabled Source address ignored 0 Enabled MAC drops frames that fail the source address filter 1 HPF Hash or perfect filter 10 1 HPF HashOnly If HM or HU is set, only frames that match the Hash filter are passed 0 HashOrPerfect If HM or HU is set, frames that match either the perfect filter or the hash filter are passed 1 RA Receive all 31 1 RA Disabled MAC receiver passes on to the application only those frames that have passed the SA/DA address file 0 Enabled MAC receiver passes oll received frames on to the application 1 MACHTHR MACHTHR Ethernet MAC hash table high register 0x8 0x20 read-write 0x00000000 HTH Upper 32 bits of hash table 0 32 0 4294967295 MACHTLR MACHTLR Ethernet MAC hash table low register 0xC 0x20 read-write 0x00000000 HTL Lower 32 bits of hash table 0 32 0 4294967295 MACMIIAR MACMIIAR Ethernet MAC MII address register 0x10 0x20 read-write 0x00000000 MB MII busy 0 1 MB Busy This bit is set to 1 by the application to indicate that a read or write access is in progress 1 MW MII write 1 1 MW Read Read operation 0 Write Write operation 1 CR Clock range 2 3 CR CR_60_100 60-100MHz HCLK/42 0 CR_100_150 100-150 MHz HCLK/62 1 CR_20_35 20-35MHz HCLK/16 2 CR_35_60 35-60MHz HCLK/16 3 CR_150_168 150-168MHz HCLK/102 4 MR MII register - select the desired MII register in the PHY device 6 5 0 31 PA PHY address - select which of possible 32 PHYs is being accessed 11 5 0 31 MACMIIDR MACMIIDR Ethernet MAC MII data register 0x14 0x20 read-write 0x00000000 MD MII data read from/written to the PHY 0 16 0 65535 MACFCR MACFCR Ethernet MAC flow control register 0x18 0x20 read-write 0x00000000 FCB Flow control busy/back pressure activate 0 1 FCB DisableBackPressure In half duplex only, deasserts back pressure 0 PauseOrBackPressure In full duplex, initiate a Pause control frame. In half duplex, assert back pressure 1 TFCE Transmit flow control enable 1 1 TFCE Disabled In full duplex, flow control is disabled. In half duplex, back pressure is disabled 0 Enabled In full duplex, flow control is enabled. In half duplex, back pressure is enabled 1 RFCE Receive flow control enable 2 1 RFCE Disabled Pause frames are not decoded 0 Enabled MAC decodes received Pause frames and disables its transmitted for a specified time 1 UPFD Unicast pause frame detect 3 1 UPFD Disabled MAC detects only a Pause frame with the multicast address specified in the 802.3x standard 0 Enabled MAC additionally detects Pause frames with the station's unicast address 1 PLT Pause low threshold 4 2 PLT PLT4 Pause time minus 4 slot times 0 PLT28 Pause time minus 28 slot times 1 PLT144 Pause time minus 144 slot times 2 PLT256 Pause time minus 256 slot times 3 ZQPD Zero-quanta pause disable 7 1 ZQPD Enabled Normal operation with automatic zero-quanta pause control frame generation 0 Disabled Automatic generation of zero-quanta pause control frames is disabled 1 PT Pause time 16 16 0 65535 MACVLANTR MACVLANTR Ethernet MAC VLAN tag register 0x1C 0x20 read-write 0x00000000 VLANTI VLAN tag identifier (for receive frames) 0 16 0 65535 VLANTC 12-bit VLAN tag comparison 16 1 VLANTC VLANTC16 Full 16 bit VLAN identifiers are used for comparison and filtering 0 VLANTC12 12 bit VLAN identifies are used for comparison and filtering 1 MACPMTCSR MACPMTCSR Ethernet MAC PMT control and status register 0x2C 0x20 read-write 0x00000000 PD Power down 0 1 PD Enabled All received frames will be dropped. Cleared automatically when a magic packet or wakeup frame is received 1 MPE Magic packet enable 1 1 MPE Disabled No power management event generated due to Magic Packet reception 0 Enabled Enable generation of a power management event due to Magic Packet reception 1 WFE Wakeup frame enable 2 1 WFE Disabled No power management event generated due to wakeup frame reception 0 Enabled Enable generation of a power management event due to wakeup frame reception 1 MPR Magic packet received 5 1 WFR Wakeup frame received 6 1 GU Global unicast 9 1 GU Disabled Normal operation 0 Enabled Any unicast packet filtered by the MAC address recognition may be a wakeup frame 1 WFFRPR Wakeup frame filter register pointer reset 31 1 WFFRPR Reset Reset wakeup frame filter register point to 0b000. Automatically cleared 1 MACDBGR MACDBGR Ethernet MAC debug register 0x34 0x20 read-only 0x00000000 TFF Tx FIFO full 25 1 TFNE Tx FIFO not empty 24 1 TFWA Tx FIFO write active 22 1 TFRS Tx FIFO read status 20 2 MTP MAC transmitter in pause 19 1 MTFCS MAC transmit frame controller status 17 2 MMTEA MAC MII transmit engine active 16 1 RFFL Rx FIFO fill level 8 2 RFRCS Rx FIFO read controller status 5 2 RFWRA Rx FIFO write controller active 4 1 MSFRWCS MAC small FIFO read/write controllers status 1 2 MMRPEA MAC MII receive protocol engine active 0 1 MACSR MACSR Ethernet MAC interrupt status register 0x38 0x20 0x00000000 PMTS PMT status 3 1 read-only MMCS MMC status 4 1 read-only MMCRS MMC receive status 5 1 read-only MMCTS MMC transmit status 6 1 read-only TSTS Time stamp trigger status 9 1 read-write MACIMR MACIMR Ethernet MAC interrupt mask register 0x3C 0x20 read-write 0x00000000 PMTIM PMT interrupt mask 3 1 PMTIM Unmasked PMT Status interrupt generation enabled 0 Masked PMT Status interrupt generation disabled 1 TSTIM Time stamp trigger interrupt mask 9 1 TSTIM Unmasked Time stamp interrupt generation enabled 0 Masked Time stamp interrupt generation disabled 1 MACA0HR MACA0HR Ethernet MAC address 0 high register 0x40 0x20 0x0010FFFF MACA0H MAC address0 high 0 16 read-write 0 65535 MO Always 1 31 1 read-only MACA0LR MACA0LR Ethernet MAC address 0 low register 0x44 0x20 read-write 0xFFFFFFFF MACA0L 0 0 32 0 4294967295 MACA1HR MACA1HR Ethernet MAC address 1 high register 0x48 0x20 read-write 0x0000FFFF MACA1H MACA1H 0 16 0 65535 MBC MBC 24 6 0 63 SA SA 30 1 SA Destination This address is used for comparison with DA fields of the received frame 0 Source This address is used for comparison with SA fields of received frames 1 AE AE 31 1 AE Disabled Address filters ignore this address 0 Enabled Address filters use this address 1 MACA1LR MACA1LR Ethernet MAC address1 low register 0x4C 0x20 read-write 0xFFFFFFFF MACA1L MACA1LR 0 32 0 4294967295 MACA2HR MACA2HR Ethernet MAC address 2 high register 0x50 0x20 read-write 0x0000FFFF MACA2H MAC2AH 0 16 0 65535 MBC MBC 24 6 0 63 SA SA 30 1 SA Destination This address is used for comparison with DA fields of the received frame 0 Source This address is used for comparison with SA fields of received frames 1 AE AE 31 1 AE Disabled Address filters ignore this address 0 Enabled Address filters use this address 1 MACA2LR MACA2LR Ethernet MAC address 2 low register 0x54 0x20 read-write 0xFFFFFFFF MACA2L MACA2L 0 32 0 4294967295 MACA3HR MACA3HR Ethernet MAC address 3 high register 0x58 0x20 read-write 0x0000FFFF MACA3H MACA3H 0 16 0 65535 MBC MBC 24 6 0 63 SA SA 30 1 SA Destination This address is used for comparison with DA fields of the received frame 0 Source This address is used for comparison with SA fields of received frames 1 AE AE 31 1 AE Disabled Address filters ignore this address 0 Enabled Address filters use this address 1 MACA3LR MACA3LR Ethernet MAC address 3 low register 0x5C 0x20 read-write 0xFFFFFFFF MACA3L MBCA3L 0 32 0 4294967295 MACRWUFFER MACRWUFFER Ethernet MAC remote wakeup frame filter register 0x60 0x20 read-write 0xFFFFFFFF Ethernet_MMC Ethernet: MAC management counters Ethernet 0x40028100 0x0 0x400 registers MMCCR MMCCR Ethernet MMC control register 0x0 0x20 read-write 0x00000000 CR Counter reset 0 1 CR Reset Reset all counters. Cleared automatically 1 CSR Counter stop rollover 1 1 CSR Disabled Counters roll over to zero after reaching the maximum value 0 Enabled Counters do not roll over to zero after reaching the maximum value 1 ROR Reset on read 2 1 ROR Disabled MMC counters do not reset on read 0 Enabled MMC counters reset to zero after read 1 MCF MMC counter freeze 3 1 MCF Unfrozen All MMC counters update normally 0 Frozen All MMC counters frozen to their current value 1 MCP MMC counter preset 4 1 MCP Preset MMC counters will be preset to almost full or almost half. Cleared automatically 1 MCFHP MMC counter Full-Half preset 5 1 MCFHP AlmostHalf When MCP is set, MMC counters are preset to almost-half value 0x7FFF_FFF0 0 AlmostFull When MCP is set, MMC counters are preset to almost-full value 0xFFFF_FFF0 1 MMCRIR MMCRIR Ethernet MMC receive interrupt register 0x4 0x20 read-write 0x00000000 RFCES Received frames CRC error status 5 1 RFAES Received frames alignment error status 6 1 RGUFS Received good Unicast frames status 17 1 MMCTIR MMCTIR Ethernet MMC transmit interrupt register 0x8 0x20 read-only 0x00000000 TGFSCS Transmitted good frames single collision status 14 1 TGFMSCS Transmitted good frames more than single collision status 15 1 TGFS Transmitted good frames status 21 1 MMCRIMR MMCRIMR Ethernet MMC receive interrupt mask register 0xC 0x20 read-write 0x00000000 RFCEM Received frame CRC error mask 5 1 RFCEM Unmasked Received-crc-error counter half-full interrupt enabled 0 Masked Received-crc-error counter half-full interrupt disabled 1 RFAEM Received frames alignment error mask 6 1 RFAEM Unmasked Received-alignment-error counter half-full interrupt enabled 0 Masked Received-alignment-error counter half-full interrupt disabled 1 RGUFM Received good Unicast frames mask 17 1 RGUFM Unmasked Received-good-unicast counter half-full interrupt enabled 0 Masked Received-good-unicast counter half-full interrupt disabled 1 MMCTIMR MMCTIMR Ethernet MMC transmit interrupt mask register 0x10 0x20 read-write 0x00000000 TGFSCM Transmitted good frames single collision mask 14 1 TGFSCM Unmasked Transmitted-good-single-collision half-full interrupt enabled 0 Masked Transmitted-good-single-collision half-full interrupt disabled 1 TGFMSCM Transmitted good frames more than single collision mask 15 1 TGFMSCM Unmasked Transmitted-good-multiple-collision half-full interrupt enabled 0 Masked Transmitted-good-multiple-collision half-full interrupt disabled 1 TGFM Transmitted good frames mask 21 1 TGFM Unmasked Transmitted-good counter half-full interrupt enabled 0 Masked Transmitted-good counter half-full interrupt disabled 1 MMCTGFSCCR MMCTGFSCCR Ethernet MMC transmitted good frames after a single collision counter 0x4C 0x20 read-only 0x00000000 TGFSCC Transmitted good frames single collision counter 0 32 MMCTGFMSCCR MMCTGFMSCCR Ethernet MMC transmitted good frames after more than a single collision 0x50 0x20 read-only 0x00000000 TGFMSCC TGFMSCC 0 32 MMCTGFCR MMCTGFCR Ethernet MMC transmitted good frames counter register 0x68 0x20 read-only 0x00000000 TGFC HTL 0 32 MMCRFCECR MMCRFCECR Ethernet MMC received frames with CRC error counter register 0x94 0x20 read-only 0x00000000 RFCFC RFCFC 0 32 MMCRFAECR MMCRFAECR Ethernet MMC received frames with alignment error counter register 0x98 0x20 read-only 0x00000000 RFAEC RFAEC 0 32 MMCRGUFCR MMCRGUFCR MMC received good unicast frames counter register 0xC4 0x20 read-only 0x00000000 RGUFC RGUFC 0 32 Ethernet_PTP Ethernet: Precision time protocol Ethernet 0x40028700 0x0 0x400 registers PTPTSCR PTPTSCR Ethernet PTP time stamp control register 0x0 0x20 read-write 0x00002000 TSE TSE 0 1 TSFCU TSFCU 1 1 TSPTPPSV2E TSPTPPSV2E 10 1 TSSPTPOEFE TSSPTPOEFE 11 1 TSSIPV6FE TSSIPV6FE 12 1 TSSIPV4FE TSSIPV4FE 13 1 TSSEME TSSEME 14 1 TSSMRME TSSMRME 15 1 TSCNT TSCNT 16 2 TSPFFMAE TSPFFMAE 18 1 TSSTI TSSTI 2 1 TSSTU TSSTU 3 1 TSITE TSITE 4 1 TTSARU TTSARU 5 1 TSSARFE TSSARFE 8 1 TSSSR TSSSR 9 1 PTPSSIR PTPSSIR Ethernet PTP subsecond increment register 0x4 0x20 read-write 0x00000000 STSSI STSSI 0 8 PTPTSHR PTPTSHR Ethernet PTP time stamp high register 0x8 0x20 read-only 0x00000000 STS STS 0 32 PTPTSLR PTPTSLR Ethernet PTP time stamp low register 0xC 0x20 read-only 0x00000000 STSS STSS 0 31 STPNS STPNS 31 1 PTPTSHUR PTPTSHUR Ethernet PTP time stamp high update register 0x10 0x20 read-write 0x00000000 TSUS TSUS 0 32 PTPTSLUR PTPTSLUR Ethernet PTP time stamp low update register 0x14 0x20 read-write 0x00000000 TSUSS TSUSS 0 31 TSUPNS TSUPNS 31 1 PTPTSAR PTPTSAR Ethernet PTP time stamp addend register 0x18 0x20 read-write 0x00000000 TSA TSA 0 32 PTPTTHR PTPTTHR Ethernet PTP target time high register 0x1C 0x20 read-write 0x00000000 TTSH 0 0 32 PTPTTLR PTPTTLR Ethernet PTP target time low register 0x20 0x20 read-write 0x00000000 TTSL TTSL 0 32 PTPTSSR PTPTSSR Ethernet PTP time stamp status register 0x28 0x20 read-only 0x00000000 TSSO TSSO 0 1 TSTTR TSTTR 1 1 PTPPPSCR PTPPPSCR Ethernet PTP PPS control register 0x2C 0x20 read-only 0x00000000 PPSFREQ PPS frequency selection 0 4 read-write PPSFREQ Hz_1 1 Hz with a pulse width of 125 ms for binary rollover and of 100 ms for digital rollover 0 Hz_2 2 Hz with 50% duty cycle for binary rollover (digital rollover not recommended) 1 Hz_4 4 Hz with 50% duty cycle for binary rollover (digital rollover not recommended) 2 Hz_8 8 Hz with 50% duty cycle for binary rollover (digital rollover not recommended) 3 Hz_16 16 Hz with 50% duty cycle for binary rollover (digital rollover not recommended) 4 Hz_32 32 Hz with 50% duty cycle for binary rollover (digital rollover not recommended) 5 Hz_64 64 Hz with 50% duty cycle for binary rollover (digital rollover not recommended) 6 Hz_128 128 Hz with 50% duty cycle for binary rollover (digital rollover not recommended) 7 Hz_256 256 Hz with 50% duty cycle for binary rollover (digital rollover not recommended) 8 Hz_512 512 Hz with 50% duty cycle for binary rollover (digital rollover not recommended) 9 Hz_1024 1024 Hz with 50% duty cycle for binary rollover (digital rollover not recommended) 10 Hz_2048 2048 Hz with 50% duty cycle for binary rollover (digital rollover not recommended) 11 Hz_4096 4096 Hz with 50% duty cycle for binary rollover (digital rollover not recommended) 12 Hz_8192 8192 Hz with 50% duty cycle for binary rollover (digital rollover not recommended) 13 Hz_16384 16384 Hz with 50% duty cycle for binary rollover (digital rollover not recommended) 14 Hz_32768 32768 Hz with 50% duty cycle for binary rollover (digital rollover not recommended) 15 Ethernet_DMA Ethernet: DMA controller operation Ethernet 0x40029000 0x0 0x400 registers ETH Ethernet global interrupt 61 ETH_WKUP Ethernet Wakeup through EXTI line interrupt 62 DMABMR DMABMR Ethernet DMA bus mode register 0x0 0x20 read-write 0x00002101 SR Software reset 0 1 SR Reset Reset all MAC subsystem internal registers and logic. Cleared automatically 1 DA DMA arbitration 1 1 DA RoundRobin Round-robin with Rx:Tx priority given by PM 0 RxPriority Rx has priority over Tx 1 DSL Descriptor skip length 2 5 0 31 EDFE Enhanced descriptor format enable 7 1 EDFE Disabled Normal descriptor format 0 Enabled Enhanced 32-byte descriptor format, required for timestamping and IPv4 checksum offload 1 PBL Programmable burst length 8 6 PBL PBL1 Maximum of 1 beat per DMA transaction 1 PBL2 Maximum of 2 beats per DMA transaction 2 PBL4 Maximum of 4 beats per DMA transaction 4 PBL8 Maximum of 8 beats per DMA transaction 8 PBL16 Maximum of 16 beats per DMA transaction 16 PBL32 Maximum of 32 beats per DMA transaction 32 PM Rx-Tx priority ratio 14 2 PM OneToOne RxDMA priority over TxDMA is 1:1 0 TwoToOne RxDMA priority over TxDMA is 2:1 1 ThreeToOne RxDMA priority over TxDMA is 3:1 2 FourToOne RxDMA priority over TxDMA is 4:1 3 FB Fixed burst 16 1 FB Variable AHB uses SINGLE and INCR burst transfers 0 Fixed AHB uses only fixed burst transfers 1 RDP Rx DMA PBL 17 6 RDP RDP1 1 beat per RxDMA transaction 1 RDP2 2 beats per RxDMA transaction 2 RDP4 4 beats per RxDMA transaction 4 RDP8 8 beats per RxDMA transaction 8 RDP16 16 beats per RxDMA transaction 16 RDP32 32 beats per RxDMA transaction 32 USP Use separate PBL 23 1 USP Combined PBL value used for both Rx and Tx DMA 0 Separate RxDMA uses RDP value, TxDMA uses PBL value 1 FPM 4xPBL mode 24 1 FPM x1 PBL values used as-is 0 x4 PBL values multiplied by 4 1 AAB Address-aligned beats 25 1 AAB Unaligned Bursts are not aligned 0 Aligned Align bursts to start address LS bits. First burst alignment depends on FB bit 1 MB Mixed burst 26 1 MB Normal Fixed burst transfers (INCRx and SINGLE) for burst lengths of 16 and below 0 Mixed If FB is low, start all bursts greater than 16 with INCR (undefined burst) 1 DMATPDR DMATPDR Ethernet DMA transmit poll demand register 0x4 0x20 read-write 0x00000000 TPD Transmit poll demand 0 32 TPD Poll Poll the transmit descriptor list 0 DMARPDR DMARPDR EHERNET DMA receive poll demand register 0x8 0x20 read-write 0x00000000 RPD Receive poll demand 0 32 RPD Poll Poll the receive descriptor list 0 DMARDLAR DMARDLAR Ethernet DMA receive descriptor list address register 0xC 0x20 read-write 0x00000000 SRL Start of receive list 0 32 DMATDLAR DMATDLAR Ethernet DMA transmit descriptor list address register 0x10 0x20 read-write 0x00000000 STL Start of transmit list 0 32 DMASR DMASR Ethernet DMA status register 0x14 0x20 0x00000000 TS Transmit status 0 1 read-write TPSS Transmit process stopped status 1 1 read-write TBUS Transmit buffer unavailable status 2 1 read-write TJTS Transmit jabber timeout status 3 1 read-write ROS Receive overflow status 4 1 read-write TUS Transmit underflow status 5 1 read-write RS Receive status 6 1 read-write RBUS Receive buffer unavailable status 7 1 read-write RPSS Receive process stopped status 8 1 read-write PWTS PWTS 9 1 read-write ETS Early transmit status 10 1 read-write FBES Fatal bus error status 13 1 read-write ERS Early receive status 14 1 read-write AIS Abnormal interrupt summary 15 1 read-write NIS Normal interrupt summary 16 1 read-write RPS Receive process state 17 3 read-only RPS Stopped Stopped, reset or Stop Receive command issued 0 RunningFetching Running, fetching receive transfer descriptor 1 RunningWaiting Running, waiting for receive packet 3 Suspended Suspended, receive descriptor unavailable 4 RunningWriting Running, writing data to host memory buffer 7 TPS Transmit process state 20 3 read-only TPS Stopped Stopped, Reset or Stop Transmit command issued 0 RunningFetching Running, fetching transmit transfer descriptor 1 RunningWaiting Running, waiting for status 2 RunningReading Running, reading data from host memory buffer 3 Suspended Suspended, transmit descriptor unavailable or transmit buffer underflow 6 Running Running, closing transmit descriptor 7 EBS Error bits status 23 3 read-only MMCS MMC status 27 1 read-only PMTS PMT status 28 1 read-only TSTS Time stamp trigger status 29 1 read-only DMAOMR DMAOMR Ethernet DMA operation mode register 0x18 0x20 read-write 0x00000000 SR Start/stop receive 1 1 SR Stopped Reception is stopped after transfer of the current frame 0 Started Reception is placed in the Running state 1 OSF Operate on second frame 2 1 RTC Receive threshold control 3 2 RTC RTC64 64 bytes 0 RTC32 32 bytes 1 RTC96 96 bytes 2 RTC128 128 bytes 3 FUGF Forward undersized good frames 6 1 FUGF Drop Rx FIFO drops all frames of less than 64 bytes 0 Forward Rx FIFO forwards undersized frames 1 FEF Forward error frames 7 1 FEF Drop Rx FIFO drops frames with error status 0 Forward All frames except runt error frames are forwarded to the DMA 1 ST Start/stop transmission 13 1 ST Stopped Transmission is placed in the Stopped state 0 Started Transmission is placed in Running state 1 TTC Transmit threshold control 14 3 TTC TTC64 64 bytes 0 TTC128 128 bytes 1 TTC192 192 bytes 2 TTC256 256 bytes 3 TTC40 40 bytes 4 TTC32 32 bytes 5 TTC24 24 bytes 6 TTC16 16 bytes 7 FTF Flush transmit FIFO 20 1 FTF Flush Transmit FIFO controller logic is reset to its default values. Cleared automatically 1 TSF Transmit store and forward 21 1 TSF CutThrough Transmission starts when the frame size in the Tx FIFO exceeds TTC threshold 0 StoreForward Transmission starts when a full frame is in the Tx FIFO 1 DFRF Disable flushing of received frames 24 1 RSF Receive store and forward 25 1 RSF CutThrough Rx FIFO operates in cut-through mode, subject to RTC bits 0 StoreForward Frames are read from Rx FIFO after complete frame has been written 1 DTCEFD Dropping of TCP/IP checksum error frames disable 26 1 DTCEFD Enabled Drop frames with errors only in the receive checksum offload engine 0 Disabled Do not drop frames that only have errors in the receive checksum offload engine 1 DMAIER DMAIER Ethernet DMA interrupt enable register 0x1C 0x20 read-write 0x00000000 TIE Transmit interrupt enable 0 1 TPSIE Transmit process stopped interrupt enable 1 1 TBUIE Transmit buffer unavailable interrupt enable 2 1 TJTIE Transmit jabber timeout interrupt enable 3 1 ROIE Receive overflow interrupt enable 4 1 TUIE Transmit underflow interrupt enable 5 1 RIE Receive interrupt enable 6 1 RBUIE Receive buffer unavailable interrupt enable 7 1 RPSIE Receive process stopped interrupt enable 8 1 RWTIE Receive watchdog timeout interrupt enable 9 1 ETIE Early transmit interrupt enable 10 1 FBEIE Fatal bus error interrupt enable 13 1 ERIE Early receive interrupt enable 14 1 AISE Abnormal interrupt summary enable 15 1 NISE Normal interrupt summary enable 16 1 DMAMFBOCR DMAMFBOCR Ethernet DMA missed frame and buffer overflow counter register 0x20 0x20 read-write 0x00000000 MFC Missed frames by the controller 0 16 OMFC Overflow bit for missed frame counter 16 1 MFA Missed frames by the application 17 11 OFOC Overflow bit for FIFO overflow counter 28 1 DMARSWTR DMARSWTR Ethernet DMA receive status watchdog timer register 0x24 0x20 read-write 0x00000000 RSWTC Receive status watchdog timer count 0 8 0 255 DMACHTDR DMACHTDR Ethernet DMA current host transmit descriptor register 0x48 0x20 read-only 0x00000000 HTDAP Host transmit descriptor address pointer 0 32 DMACHRDR DMACHRDR Ethernet DMA current host receive descriptor register 0x4C 0x20 read-only 0x00000000 HRDAP Host receive descriptor address pointer 0 32 DMACHTBAR DMACHTBAR Ethernet DMA current host transmit buffer address register 0x50 0x20 read-only 0x00000000 HTBAP Host transmit buffer address pointer 0 32 DMACHRBAR DMACHRBAR Ethernet DMA current host receive buffer address register 0x54 0x20 read-only 0x00000000 HRBAP Host receive buffer address pointer 0 32 CRC Cryptographic processor CRC 0x40023000 0x0 0x400 registers DR DR Data register 0x0 0x20 read-write 0xFFFFFFFF DR Data Register 0 32 0 4294967295 DR8 Data register - byte sized DR 0x0 0x8 read-write 0x000000FF DR8 Data register bits 0 8 0 255 DR16 Data register - half-word sized DR 0x0 0x10 read-write 0x0000FFFF DR16 Data register bits 0 16 0 65535 IDR IDR Independent Data register 0x4 0x20 read-write 0x00000000 IDR Independent Data register 0 8 0 255 CR CR Control register 0x8 0x20 write-only 0x00000000 RESET RESET bit 0 1 RESETW Reset Resets the CRC calculation unit and sets the data register to 0xFFFF FFFF 1 REV_OUT Reverse output data 7 1 read-write REV_OUT Normal Bit order not affected 0 Reversed Bit reversed output 1 REV_IN Reverse input data 5 2 read-write REV_IN Normal Bit order not affected 0 Byte Bit reversal done by byte 1 HalfWord Bit reversal done by half-word 2 Word Bit reversal done by word 3 POLYSIZE Polynomial size 3 2 read-write POLYSIZE Polysize32 32-bit polynomial 0 Polysize16 16-bit polynomial 1 Polysize8 8-bit polynomial 2 Polysize7 7-bit polynomial 3 INIT INIT Initial CRC value 0x10 0x20 read-write 0x00000000 INIT Programmable initial CRC value 0 32 0 4294967295 POL POL CRC polynomial 0x14 0x20 read-write 0x00000000 POL Programmable polynomial 0 32 0 4294967295 CAN1 Controller area network CAN 0x40006400 0x0 0x400 registers CAN1_TX CAN1 TX interrupts 19 CAN1_RX0 CAN1 RX0 interrupts 20 CAN1_RX1 CAN1 RX1 interrupts 21 CAN1_SCE CAN1 SCE interrupt 22 MCR MCR master control register 0x0 0x20 read-write 0x00010002 DBF DBF 16 1 RESET RESET 15 1 TTCM TTCM 7 1 ABOM ABOM 6 1 AWUM AWUM 5 1 NART NART 4 1 RFLM RFLM 3 1 TXFP TXFP 2 1 SLEEP SLEEP 1 1 INRQ INRQ 0 1 MSR MSR master status register 0x4 0x20 0x00000C02 RX RX 11 1 read-only SAMP SAMP 10 1 read-only RXM RXM 9 1 read-only TXM TXM 8 1 read-only SLAKI SLAKI 4 1 read-write WKUI WKUI 3 1 read-write ERRI ERRI 2 1 read-write SLAK SLAK 1 1 read-only INAK INAK 0 1 read-only TSR TSR transmit status register 0x8 0x20 0x1C000000 3 0x1 0-2 LOW%s Lowest priority flag for mailbox %s 29 1 read-only 3 0x1 0-2 TME%s Lowest priority flag for mailbox %s 26 1 read-only CODE CODE 24 2 read-only 3 0x8 0-2 ABRQ%s ABRQ%s 7 1 read-write 3 0x8 0-2 TERR%s TERR%s 3 1 read-write 3 0x8 0-2 ALST%s ALST%s 2 1 read-write 3 0x8 0-2 TXOK%s TXOK%s 1 1 read-write 3 0x8 0-2 RQCP%s RQCP%s 0 1 read-write 2 0x4 0-1 RF%sR RF%sR receive FIFO %s register 0xC 0x20 0x00000000 RFOM RFOM0 5 1 read-write RFOM0W write Release Set by software to release the output mailbox of the FIFO 1 FOVR FOVR0 4 1 read-write FOVR0R read NoOverrun No FIFO x overrun 0 Overrun FIFO x overrun 1 FOVR0W write Clear Clear flag 1 FULL FULL0 3 1 read-write FULL0R read NotFull FIFO x is not full 0 Full FIFO x is full 1 FULL0W write Clear Clear flag 1 FMP FMP0 0 2 read-only IER IER interrupt enable register 0x14 0x20 read-write 0x00000000 SLKIE SLKIE 17 1 SLKIE Disabled No interrupt when SLAKI bit is set 0 Enabled Interrupt generated when SLAKI bit is set 1 WKUIE WKUIE 16 1 WKUIE Disabled No interrupt when WKUI is set 0 Enabled Interrupt generated when WKUI bit is set 1 ERRIE ERRIE 15 1 ERRIE Disabled No interrupt will be generated when an error condition is pending in the CAN_ESR 0 Enabled An interrupt will be generation when an error condition is pending in the CAN_ESR 1 LECIE LECIE 11 1 LECIE Disabled ERRI bit will not be set when the error code in LEC[2:0] is set by hardware on error detection 0 Enabled ERRI bit will be set when the error code in LEC[2:0] is set by hardware on error detection 1 BOFIE BOFIE 10 1 BOFIE Disabled ERRI bit will not be set when BOFF is set 0 Enabled ERRI bit will be set when BOFF is set 1 EPVIE EPVIE 9 1 EPVIE Disabled ERRI bit will not be set when EPVF is set 0 Enabled ERRI bit will be set when EPVF is set 1 EWGIE EWGIE 8 1 EWGIE Disabled ERRI bit will not be set when EWGF is set 0 Enabled ERRI bit will be set when EWGF is set 1 FOVIE1 FOVIE1 6 1 FOVIE1 Disabled No interrupt when FOVR is set 0 Enabled Interrupt generation when FOVR is set 1 FFIE1 FFIE1 5 1 FFIE1 Disabled No interrupt when FULL bit is set 0 Enabled Interrupt generated when FULL bit is set 1 FMPIE1 FMPIE1 4 1 FMPIE1 Disabled No interrupt generated when state of FMP[1:0] bits are not 00b 0 Enabled Interrupt generated when state of FMP[1:0] bits are not 00b 1 FOVIE0 FOVIE0 3 1 FOVIE0 Disabled No interrupt when FOVR bit is set 0 Enabled Interrupt generated when FOVR bit is set 1 FFIE0 FFIE0 2 1 FFIE0 Disabled No interrupt when FULL bit is set 0 Enabled Interrupt generated when FULL bit is set 1 FMPIE0 FMPIE0 1 1 FMPIE0 Disabled No interrupt generated when state of FMP[1:0] bits are not 00 0 Enabled Interrupt generated when state of FMP[1:0] bits are not 00b 1 TMEIE TMEIE 0 1 TMEIE Disabled No interrupt when RQCPx bit is set 0 Enabled Interrupt generated when RQCPx bit is set 1 ESR ESR interrupt enable register 0x18 0x20 0x00000000 REC REC 24 8 read-only TEC TEC 16 8 read-only LEC LEC 4 3 read-write LEC NoError No Error 0 Stuff Stuff Error 1 Form Form Error 2 Ack Acknowledgment Error 3 BitRecessive Bit recessive Error 4 BitDominant Bit dominant Error 5 Crc CRC Error 6 Custom Set by software 7 BOFF BOFF 2 1 read-only EPVF EPVF 1 1 read-only EWGF EWGF 0 1 read-only BTR BTR bit timing register 0x1C 0x20 read-write 0x00000000 SILM SILM 31 1 SILM Normal Normal operation 0 Silent Silent Mode 1 LBKM LBKM 30 1 LBKM Disabled Loop Back Mode disabled 0 Enabled Loop Back Mode enabled 1 SJW SJW 24 2 TS2 TS2 20 3 TS1 TS1 16 4 BRP BRP 0 10 3 0x10 0-2 TX%s CAN Transmit cluster 0x180 TIR TI0R TX mailbox identifier register 0x0 0x20 read-write 0x00000000 STID STID 21 11 EXID EXID 3 18 IDE IDE 2 1 IDE Standard Standard identifier 0 Extended Extended identifier 1 RTR RTR 1 1 RTR Data Data frame 0 Remote Remote frame 1 TXRQ TXRQ 0 1 TDTR TDT0R mailbox data length control and time stamp register 0x4 0x20 read-write 0x00000000 TIME TIME 16 16 TGT TGT 8 1 DLC DLC 0 4 0 8 TDLR TDL0R mailbox data low register 0x8 0x20 read-write 0x00000000 4 0x8 0-3 DATA%s DATA%s 0 8 TDHR TDH0R mailbox data high register 0xC 0x20 read-write 0x00000000 4 0x8 4-7 DATA%s DATA%s 0 8 2 0x10 0-1 RX%s CAN Receive cluster 0x1B0 RIR RI0R receive FIFO mailbox identifier register 0x0 0x20 read-only 0x00000000 STID STID 21 11 EXID EXID 3 18 IDE IDE 2 1 IDE Standard Standard identifier 0 Extended Extended identifier 1 RTR RTR 1 1 RTR Data Data frame 0 Remote Remote frame 1 RDTR RDT0R mailbox data high register 0x4 0x20 read-only 0x00000000 TIME TIME 16 16 FMI FMI 8 8 DLC DLC 0 4 0 8 RDLR RDL0R mailbox data high register 0x8 0x20 read-only 0x00000000 4 0x8 0-3 DATA%s DATA%s 0 8 RDHR RDH0R receive FIFO mailbox data high register 0xC 0x20 read-only 0x00000000 4 0x8 4-7 DATA%s DATA%s 0 8 FMR FMR filter master register 0x200 0x20 read-write 0x2A1C0E01 CAN2SB CAN2SB 8 6 FINIT FINIT 0 1 FM1R FM1R filter mode register 0x204 0x20 read-write 0x00000000 28 0x1 0-27 FBM%s Filter mode 0 1 FS1R FS1R filter scale register 0x20C 0x20 read-write 0x00000000 28 0x1 0-27 FSC%s Filter scale configuration 0 1 FFA1R FFA1R filter FIFO assignment register 0x214 0x20 read-write 0x00000000 28 0x1 0-27 FFA%s Filter FIFO assignment for filter %s 0 1 FA1R FA1R filter activation register 0x21C 0x20 read-write 0x00000000 28 0x1 0-27 FACT%s Filter active 0 1 28 0x8 0-27 FB%s CAN Filter Bank cluster 0x240 FR1 F0R1 Filter bank x register 1 0x0 0x20 read-write 0x00000000 FB Filter bits 0 32 FR2 F0R2 Filter bank x register 2 0x4 0x20 read-write 0x00000000 FB Filter bits 0 32 CAN2 0x40006800 CAN2_TX CAN2 TX interrupts 63 CAN2_RX0 CAN2 RX0 interrupts 64 CAN2_RX1 CAN2 RX1 interrupts 65 CAN2_SCE CAN2 SCE interrupt 66 FLASH FLASH FLASH 0x40023C00 0x0 0x400 registers FLASH Flash global interrupt 4 ACR ACR Flash access control register 0x0 0x20 read-write 0x00000000 LATENCY Latency 0 4 LATENCY WS0 0 wait states 0 WS1 1 wait states 1 WS2 2 wait states 2 WS3 3 wait states 3 WS4 4 wait states 4 WS5 5 wait states 5 WS6 6 wait states 6 WS7 7 wait states 7 WS8 8 wait states 8 WS9 9 wait states 9 WS10 10 wait states 10 WS11 11 wait states 11 WS12 12 wait states 12 WS13 13 wait states 13 WS14 14 wait states 14 WS15 15 wait states 15 PRFTEN Prefetch enable 8 1 PRFTEN Disabled Prefetch is disabled 0 Enabled Prefetch is enabled 1 ARTEN ART Accelerator Enable 9 1 ARTEN Disabled ART Accelerator is disabled 0 Enabled ART Accelerator is enabled 1 ARTRST ART Accelerator reset 11 1 ARTRST NoReset Accelerator is not reset 0 Reset Accelerator is reset 1 KEYR KEYR Flash key register 0x4 0x20 write-only 0x00000000 KEY FPEC key 0 32 0 4294967295 OPTKEYR OPTKEYR Flash option key register 0x8 0x20 write-only 0x00000000 OPTKEYR Option byte key 0 32 0 4294967295 SR SR Status register 0xC 0x20 0x00000000 EOP End of operation 0 1 read-write oneToClear EOPR read Inactive No error 0 Active One or more Flash operations has/have completed successfully 1 EOPW write Clear Clear error flag 1 OPERR Operation error 1 1 read-write oneToClear OPERRR read Inactive No error 0 Active A Flash operation request is detected and cannot be run because of parallelism 1 OPERRW write Clear Clear error flag 1 WRPERR Write protection error 4 1 read-write oneToClear WRPERRR read Inactive No error 0 Active The address to be erased/programmed belongs to a write-protected part of the Flash memory 1 WRPERRW write Clear Clear error flag 1 PGAERR Programming alignment error 5 1 read-write oneToClear PGAERRR read Inactive No error 0 Active The data to program cannot be contained in the same 128-bit Flash memory row 1 PGAERRW write Clear Clear error flag 1 PGPERR Programming parallelism error 6 1 read-write oneToClear PGPERRR read Inactive No error 0 Active The size of the access during the program sequence doesn't correspond to the parallelism configuration PSIZE 1 PGPERRW write Clear Clear error flag 1 ERSERR Erase Sequence Error 7 1 read-write oneToClear ERSERRR read Inactive No error 0 Active A write access to the Flash memory is performed by the code while the control register has not been correctly configured 1 ERSERRW write Clear Clear error flag 1 BSY Busy 16 1 read-only BSYR NotBusy No Flash memory operation ongoing 0 Busy Flash memory operation ongoing 1 CR CR Control register 0x10 0x20 read-write 0x80000000 PG Programming 0 1 PG Program Flash programming activated 1 SER Sector Erase 1 1 SER SectorErase Erase activated for selected sector 1 MER Mass Erase of sectors 0 to 11 2 1 MER MassErase Erase activated for all user sectors 1 SNB Sector number 3 5 0 11 PSIZE Program size 8 2 PSIZE PSIZE8 Program x8 0 PSIZE16 Program x16 1 PSIZE32 Program x32 2 PSIZE64 Program x64 3 MER1 Mass Erase of sectors 12 to 23 15 1 STRT Start 16 1 STRT Start Trigger an erase operation 1 EOPIE End of operation interrupt enable 24 1 EOPIE Disabled End of operation interrupt disabled 0 Enabled End of operation interrupt enabled 1 ERRIE Error interrupt enable 25 1 ERRIE Disabled Error interrupt generation disabled 0 Enabled Error interrupt generation enabled 1 LOCK Lock 31 1 LOCK Unlocked FLASH_CR register is unlocked 0 Locked FLASH_CR register is locked 1 OPTCR OPTCR Flash option control register 0x14 0x20 read-write 0x0FFFAAED OPTLOCK Option lock 0 1 OPTLOCKR read Unlocked The write and erase operations in the Option bytes area are disabled 0 Locked The write and erase operations in the Option bytes area are enabled 1 OPTLOCKW write Set Lock the FLASH_OPTCR register 1 OPTSTRT Option start 1 1 OPTSTRTR read Complete Cleared when BSY bit is cleared in SR 0 Requested Options modification requested 1 OPTSTRTW write Set This bit triggers an options operation when set 1 BOR_LEV BOR reset Level 2 2 BOR_LEV BOR_Off Reset threshold level for POR/PDR (around 1.7V) 0 BOR_Level1 Reset threshold level for VBOR1 (around 2.2 V) 1 BOR_Level2 Reset threshold level for VBOR2 (around 2.5 V) 2 BOR_Level3 Reset threshold level for VBOR3 (around 2.8 V) 3 WWDG_SW User option bytes 4 1 WWDG_SW Hardware Hardware window watchdog 0 Software Software window watchdog 1 IWDG_SW User option bytes 5 1 IWDG_SW Hardware Hardware independant watchdog 0 Software Software independant watchdog 1 nRST_STOP User option bytes 6 1 nRST_STOP Reset Reset generated when entering Stop mode 0 NoReset No reset generated 1 nRST_STDBY User option bytes 7 1 nRST_STDBY Reset Reset generated when entering Standby mode 0 NoReset No reset generated 1 RDP Read protect 8 8 RDP Level0 Read protection not active 170 Level2 Chip read protection active 204 Level1 Read protection of memories active true IWDG_STDBY Independent watchdog counter freeze in standby mode 30 1 IWDG_STDBY Inactive IWDG counter frozen in Standby mode 0 Active IWDG counter active in Standby mode 1 IWDG_STOP Independent watchdog counter freeze in Stop mode 31 1 IWDG_STOP Inactive IWDG counter frozen in Stop mode 0 Active IWDG counter active in Stop mode 1 8 0x1 0-7 nWRP%s Not write protect 16 1 nWRP0 Active Write protection active on sector %s 0 Inactive Write protection inactive on sector %s 1 OPTCR1 OPTCR1 Flash option control register 1 0x18 0x20 read-write 0x0FFF0000 BOOT_ADD0 Boot base address when Boot pin =0 0 16 BOOT_ADD0 ItcmRam Boot from ITCM RAM (0x0000 0000) 0 SystemMemoryBootloader Boot from System memory bootloader (0x0010 0000) 64 FlashItcmInterface Boot from Flash on ITCM interface (0x0020 0000) 128 FlashAximInterface Boot from Flash on AXIM interface (0x0800 0000) 8192 DtcmRam Boot from DTCM RAM (0x2000 0000) 32768 Sram1 Boot from SRAM1 (0x2001 0000) 32772 Sram2 Boot from SRAM2 (0x2003 C000) 32787 BootAddress Boot from specified address (granularity of 16KB) true BOOT_ADD1 Boot base address when Boot pin =1 16 16 BOOT_ADD1 ItcmRam Boot from ITCM RAM (0x0000 0000) 0 SystemMemoryBootloader Boot from System memory bootloader (0x0010 0000) 64 FlashItcmInterface Boot from Flash on ITCM interface (0x0020 0000) 128 FlashAximInterface Boot from Flash on AXIM interface (0x0800 0000) 8192 DtcmRam Boot from DTCM RAM (0x2000 0000) 32768 Sram1 Boot from SRAM1 (0x2001 0000) 32772 Sram2 Boot from SRAM2 (0x2003 C000) 32787 BootAddress Boot from specified address (granularity of 16KB) true EXTI External interrupt/event controller EXTI 0x40013C00 0x0 0x400 registers TAMP_STAMP Tamper and TimeStamp interrupts through the EXTI line 2 EXTI0 EXTI Line0 interrupt 6 EXTI1 EXTI Line1 interrupt 7 EXTI2 EXTI Line2 interrupt 8 EXTI3 EXTI Line3 interrupt 9 EXTI4 EXTI Line4 interrupt 10 EXTI9_5 EXTI Line[9:5] interrupts 23 EXTI15_10 EXTI Line[15:10] interrupts 40 FPU Floating point unit interrupt 81 IMR IMR Interrupt mask register (EXTI_IMR) 0x0 0x20 read-write 0x00000000 23 0x1 0-22 MR%s Interrupt Mask on line %s 0 1 InterruptMask Masked Interrupt request line is masked 0 Unmasked Interrupt request line is unmasked 1 EMR EMR Event mask register (EXTI_EMR) 0x4 0x20 read-write 0x00000000 23 0x1 0-22 MR%s Event Mask on line %s 0 1 EventMask Masked Event request line is masked 0 Unmasked Event request line is unmasked 1 RTSR RTSR Rising Trigger selection register (EXTI_RTSR) 0x8 0x20 read-write 0x00000000 23 0x1 0-22 TR%s Rising trigger event configuration of line %s 0 1 RisingTrigger Disabled Rising edge trigger is disabled 0 Enabled Rising edge trigger is enabled 1 FTSR FTSR Falling Trigger selection register (EXTI_FTSR) 0xC 0x20 read-write 0x00000000 23 0x1 0-22 TR%s Falling trigger event configuration of line %s 0 1 FallingTrigger Disabled Falling edge trigger is disabled 0 Enabled Falling edge trigger is enabled 1 SWIER SWIER Software interrupt event register (EXTI_SWIER) 0x10 0x20 read-write 0x00000000 23 0x1 0-22 SWIER%s Software Interrupt on line %s 0 1 SoftwareInterrupt write Pend Generates an interrupt request 1 PR PR Pending register (EXTI_PR) 0x14 0x20 read-write 0x00000000 23 0x1 0-22 PR%s Pending bit %s 0 1 oneToClear PR0R read NotPending No trigger request occurred 0 Pending Selected trigger request occurred 1 PR0W write Clear Clears pending bit 1 LTDC LCD-TFT Controller LTDC 0x40016800 0x0 0x400 registers LTDC LTDC global interrupt 88 LTDC_ER LTDC global error interrupt 89 SSCR SSCR Synchronization Size Configuration Register 0x8 0x20 read-write 0x00000000 HSW Horizontal Synchronization Width (in units of pixel clock period) 16 12 0 4095 VSH Vertical Synchronization Height (in units of horizontal scan line) 0 11 0 2047 BPCR BPCR Back Porch Configuration Register 0xC 0x20 read-write 0x00000000 AHBP Accumulated Horizontal back porch (in units of pixel clock period) 16 12 0 4095 AVBP Accumulated Vertical back porch (in units of horizontal scan line) 0 11 0 2047 AWCR AWCR Active Width Configuration Register 0x10 0x20 read-write 0x00000000 AAW Accumulated Active Width (in units of pixel clock period) 16 12 0 4095 AAH Accumulated Active Height (in units of horizontal scan line) 0 11 0 2047 TWCR TWCR Total Width Configuration Register 0x14 0x20 read-write 0x00000000 TOTALW Total Width (in units of pixel clock period) 16 12 0 4095 TOTALH Total Height (in units of horizontal scan line) 0 11 0 2047 GCR GCR Global Control Register 0x18 0x20 0x00002220 HSPOL Horizontal Synchronization Polarity 31 1 read-write HSPOL ActiveLow Horizontal synchronization polarity is active low 0 ActiveHigh Horizontal synchronization polarity is active high 1 VSPOL Vertical Synchronization Polarity 30 1 read-write VSPOL ActiveLow Vertical synchronization polarity is active low 0 ActiveHigh Vertical synchronization polarity is active high 1 DEPOL Data Enable Polarity 29 1 read-write DEPOL ActiveLow Data enable polarity is active low 0 ActiveHigh Data enable polarity is active high 1 PCPOL Pixel Clock Polarity 28 1 read-write PCPOL RisingEdge Pixel clock on rising edge 0 FallingEdge Pixel clock on falling edge 1 DEN Dither Enable 16 1 read-write DEN Disabled Dither disabled 0 Enabled Dither enabled 1 DRW Dither Red Width 12 3 read-only DGW Dither Green Width 8 3 read-only DBW Dither Blue Width 4 3 read-only LTDCEN LCD-TFT controller enable bit 0 1 read-write LTDCEN Disabled LCD-TFT controller disabled 0 Enabled LCD-TFT controller enabled 1 SRCR SRCR Shadow Reload Configuration Register 0x24 0x20 read-write 0x00000000 VBR Vertical Blanking Reload 1 1 VBR NoEffect This bit is set by software and cleared only by hardware after reload (it cannot be cleared through register write once it is set) 0 Reload The shadow registers are reloaded during the vertical blanking period (at the beginning of the first line after the active display area). 1 IMR Immediate Reload 0 1 IMR NoEffect This bit is set by software and cleared only by hardware after reload (it cannot be cleared through register write once it is set) 0 Reload The shadow registers are reloaded immediately. This bit is set by software and cleared only by hardware after reload 1 BCCR BCCR Background Color Configuration Register 0x2C 0x20 read-write 0x00000000 BCBLUE Background color blue value 0 8 0 255 BCGREEN Background color green value 8 8 0 255 BCRED Background color red value 16 8 0 255 IER IER Interrupt Enable Register 0x34 0x20 read-write 0x00000000 RRIE Register Reload interrupt enable 3 1 RRIE Disabled Register reload interrupt disabled 0 Enabled Register reload interrupt enabled 1 TERRIE Transfer Error Interrupt Enable 2 1 TERRIE Disabled Transfer error interrupt disabled 0 Enabled Transfer error interrupt enabled 1 FUIE FIFO Underrun Interrupt Enable 1 1 FUIE Disabled FIFO underrun interrupt disabled 0 Enabled FIFO underrun interrupt enabled 1 LIE Line Interrupt Enable 0 1 LIE Disabled Line interrupt disabled 0 Enabled Line interrupt enabled 1 ISR ISR Interrupt Status Register 0x38 0x20 read-only 0x00000000 RRIF Register Reload Interrupt Flag 3 1 RRIF NoReload No register reload 0 Reload Register reload interrupt generated when a vertical blanking reload occurs (and the first line after the active area is reached) 1 TERRIF Transfer Error interrupt flag 2 1 TERRIF NoError No transfer error 0 Error Transfer error interrupt generated when a bus error occurs 1 FUIF FIFO Underrun Interrupt flag 1 1 FUIF NoUnderrun No FIFO underrun 0 Underrun FIFO underrun interrupt generated, if one of the layer FIFOs is empty and pixel data is read from the FIFO 1 LIF Line Interrupt flag 0 1 LIF NotReached Programmed line not reached 0 Reached Line interrupt generated when a programmed line is reached 1 ICR ICR Interrupt Clear Register 0x3C 0x20 write-only 0x00000000 CRRIF Clears Register Reload Interrupt Flag 3 1 oneToClear CRRIFW Clear Clears the RRIF flag in the ISR register 1 CTERRIF Clears the Transfer Error Interrupt Flag 2 1 oneToClear CTERRIFW Clear Clears the TERRIF flag in the ISR register 1 CFUIF Clears the FIFO Underrun Interrupt flag 1 1 oneToClear CFUIFW Clear Clears the FUIF flag in the ISR register 1 CLIF Clears the Line Interrupt Flag 0 1 oneToClear CLIFW Clear Clears the LIF flag in the ISR register 1 LIPCR LIPCR Line Interrupt Position Configuration Register 0x40 0x20 read-write 0x00000000 LIPOS Line Interrupt Position 0 11 0 2047 CPSR CPSR Current Position Status Register 0x44 0x20 read-only 0x00000000 CXPOS Current X Position 16 16 CYPOS Current Y Position 0 16 CDSR CDSR Current Display Status Register 0x48 0x20 read-only 0x0000000F HSYNCS Horizontal Synchronization display Status 3 1 HSYNCS NotActive Currently not in HSYNC phase 0 Active Currently in HSYNC phase 1 VSYNCS Vertical Synchronization display Status 2 1 VSYNCS NotActive Currently not in VSYNC phase 0 Active Currently in VSYNC phase 1 HDES Horizontal Data Enable display Status 1 1 HDES NotActive Currently not in horizontal Data Enable phase 0 Active Currently in horizontal Data Enable phase 1 VDES Vertical Data Enable display Status 0 1 VDES NotActive Currently not in vertical Data Enable phase 0 Active Currently in vertical Data Enable phase 1 2 0x80 1-2 LAYER%s Cluster LAYER%s, containing L?CR, L?WHPCR, L?WVPCR, L?CKCR, L?PFCR, L?CACR, L?DCCR, L?BFCR, L?CFBAR, L?CFBLR, L?CFBLNR, L?CLUTWR 0x84 CR L1CR Layerx Control Register 0x0 0x20 read-write 0x00000000 CLUTEN Color Look-Up Table Enable 4 1 CLUTEN Disabled Color look-up table disabled 0 Enabled Color look-up table enabled 1 COLKEN Color Keying Enable 1 1 COLKEN Disabled Color keying disabled 0 Enabled Color keying enabled 1 LEN Layer Enable 0 1 LEN Disabled Layer disabled 0 Enabled Layer enabled 1 WHPCR L1WHPCR Layerx Window Horizontal Position Configuration Register 0x4 0x20 read-write 0x00000000 WHSPPOS Window Horizontal Stop Position 16 12 0 4095 WHSTPOS Window Horizontal Start Position 0 12 0 4095 WVPCR L1WVPCR Layerx Window Vertical Position Configuration Register 0x8 0x20 read-write 0x00000000 WVSPPOS Window Vertical Stop Position 16 11 0 2047 WVSTPOS Window Vertical Start Position 0 11 0 2047 CKCR L1CKCR Layerx Color Keying Configuration Register 0xC 0x20 read-write 0x00000000 CKRED Color Key Red value 16 8 0 255 CKGREEN Color Key Green value 8 8 0 255 CKBLUE Color Key Blue value 0 8 0 255 PFCR L1PFCR Layerx Pixel Format Configuration Register 0x10 0x20 read-write 0x00000000 PF Pixel Format 0 3 PF ARGB8888 ARGB8888 0 RGB888 RGB888 1 RGB565 RGB565 2 ARGB1555 ARGB1555 3 ARGB4444 ARGB4444 4 L8 L8 (8-bit luminance) 5 AL44 AL44 (4-bit alpha, 4-bit luminance) 6 AL88 AL88 (8-bit alpha, 8-bit luminance) 7 CACR L1CACR Layerx Constant Alpha Configuration Register 0x14 0x20 read-write 0x00000000 CONSTA Constant Alpha 0 8 0 255 DCCR L1DCCR Layerx Default Color Configuration Register 0x18 0x20 read-write 0x00000000 DCALPHA Default Color Alpha 24 8 0 255 DCRED Default Color Red 16 8 0 255 DCGREEN Default Color Green 8 8 0 255 DCBLUE Default Color Blue 0 8 0 255 BFCR L1BFCR Layerx Blending Factors Configuration Register 0x1C 0x20 read-write 0x00000607 BF1 Blending Factor 1 8 3 BF1 Constant BF1 = constant alpha 4 Pixel BF1 = pixel alpha * constant alpha 6 BF2 Blending Factor 2 0 3 BF2 Constant BF2 = 1 - constant alpha 5 Pixel BF2 = 1 - pixel alpha * constant alpha 7 CFBAR L1CFBAR Layerx Color Frame Buffer Address Register 0x28 0x20 read-write 0x00000000 CFBADD Color Frame Buffer Start Address 0 32 0 4294967295 CFBLR L1CFBLR Layerx Color Frame Buffer Length Register 0x2C 0x20 read-write 0x00000000 CFBP Color Frame Buffer Pitch in bytes 16 13 0 8191 CFBLL Color Frame Buffer Line Length 0 13 0 8191 CFBLNR L1CFBLNR Layerx ColorFrame Buffer Line Number Register 0x30 0x20 read-write 0x00000000 CFBLNBR Frame Buffer Line Number 0 11 0 2047 CLUTWR L1CLUTWR Layerx CLUT Write Register 0x40 0x20 write-only 0x00000000 CLUTADD CLUT Address 24 8 0 255 RED Red value 16 8 0 255 GREEN Green value 8 8 0 255 BLUE Blue value 0 8 0 255 SAI1 Serial audio interface SAI 0x40015800 0x0 0x400 registers SAI1 SAI1 global interrupt 87 2 0x20 A,B CH%s Cluster CH%s, containing ?CR1, ?CR2, ?FRCR, ?SLOTR, ?IM, ?SR, ?CLRFR, ?DR 0x4 CR1 ACR1 AConfiguration register 1 0x0 0x20 read-write 0x00000040 MCKDIV Master clock divider 20 4 NODIV No divider 19 1 NODIV MasterClock MCLK output is enabled. Forces the ratio between FS and MCLK to 256 or 512 according to the OSR value 0 NoDiv MCLK output enable set by the MCKEN bit (where present, else 0). Ratio between FS and MCLK depends on FRL. 1 DMAEN DMA enable 17 1 DMAEN Disabled DMA disabled 0 Enabled DMA enabled 1 SAIEN Audio block A enable 16 1 SAIEN Disabled SAI audio block disabled 0 Enabled SAI audio block enabled 1 OUTDRIV Output drive 13 1 OUTDRIV OnStart Audio block output driven when SAIEN is set 0 Immediately Audio block output driven immediately after the setting of this bit 1 MONO Mono mode 12 1 MONO Stereo Stereo mode 0 Mono Mono mode 1 SYNCEN Synchronization enable 10 2 SYNCEN Asynchronous audio sub-block in asynchronous mode 0 Internal audio sub-block is synchronous with the other internal audio sub-block. In this case, the audio sub-block must be configured in slave mode 1 External audio sub-block is synchronous with an external SAI embedded peripheral. In this case the audio sub-block should be configured in Slave mode 2 CKSTR Clock strobing edge 9 1 CKSTR FallingEdge Data strobing edge is falling edge of SCK 0 RisingEdge Data strobing edge is rising edge of SCK 1 LSBFIRST Least significant bit first 8 1 LSBFIRST MsbFirst Data are transferred with MSB first 0 LsbFirst Data are transferred with LSB first 1 DS Data size 5 3 DS Bit8 8 bits 2 Bit10 10 bits 3 Bit16 16 bits 4 Bit20 20 bits 5 Bit24 24 bits 6 Bit32 32 bits 7 PRTCFG Protocol configuration 2 2 PRTCFG Free Free protocol. Free protocol allows to use the powerful configuration of the audio block to address a specific audio protocol 0 Spdif SPDIF protocol 1 Ac97 AC’97 protocol 2 MODE Audio block mode 0 2 MODE MasterTx Master transmitter 0 MasterRx Master receiver 1 SlaveTx Slave transmitter 2 SlaveRx Slave receiver 3 CR2 ACR2 AConfiguration register 2 0x4 0x20 read-write 0x00000000 COMP Companding mode 14 2 read-write COMP NoCompanding No companding algorithm 0 MuLaw μ-Law algorithm 2 ALaw A-Law algorithm 3 CPL Complement bit 13 1 read-write CPL OnesComplement 1’s complement representation 0 TwosComplement 2’s complement representation 1 MUTECNT Mute counter 7 6 read-write MUTEVAL Mute value 6 1 read-write MUTEVAL SendZero Bit value 0 is sent during the mute mode 0 SendLast Last values are sent during the mute mode 1 MUTE Mute 5 1 read-write MUTE Disabled No mute mode 0 Enabled Mute mode enabled 1 TRIS Tristate management on data line 4 1 read-write FFLUSH FIFO flush 3 1 write-only FFLUSH NoFlush No FIFO flush 0 Flush FIFO flush. Programming this bit to 1 triggers the FIFO Flush. All the internal FIFO pointers (read and write) are cleared 1 FTH FIFO threshold 0 3 read-write FTH Empty FIFO empty 0 Quarter1 1⁄4 FIFO 1 Quarter2 1⁄2 FIFO 2 Quarter3 3⁄4 FIFO 3 Full FIFO full 4 FRCR AFRCR AFRCR 0x8 0x20 read-write 0x00000007 FSOFF Frame synchronization offset 18 1 read-write FSOFF OnFirst FS is asserted on the first bit of the slot 0 0 BeforeFirst FS is asserted one bit before the first bit of the slot 0 1 FSPOL Frame synchronization polarity 17 1 read-write FSPOL FallingEdge FS is active low (falling edge) 0 RisingEdge FS is active high (rising edge) 1 FSDEF Frame synchronization definition 16 1 read-write FSALL Frame synchronization active level length 8 7 read-write FRL Frame length 0 8 read-write SLOTR ASLOTR ASlot register 0xC 0x20 read-write 0x00000000 SLOTEN Slot enable 16 16 SLOTEN Inactive Inactive slot 0 Active Active slot 1 NBSLOT Number of slots in an audio frame 8 4 SLOTSZ Slot size 6 2 SLOTSZ DataSize The slot size is equivalent to the data size (specified in DS[3:0] in the SAI_xCR1 register) 0 Bit16 16-bit 1 Bit32 32-bit 2 FBOFF First bit offset 0 5 IM AIM AInterrupt mask register2 0x10 0x20 read-write 0x00000000 LFSDETIE Late frame synchronization detection interrupt enable 6 1 LFSDETIE Disabled Interrupt is disabled 0 Enabled Interrupt is enabled 1 AFSDETIE Anticipated frame synchronization detection interrupt enable 5 1 AFSDETIE Disabled Interrupt is disabled 0 Enabled Interrupt is enabled 1 CNRDYIE Codec not ready interrupt enable 4 1 CNRDYIE Disabled Interrupt is disabled 0 Enabled Interrupt is enabled 1 FREQIE FIFO request interrupt enable 3 1 FREQIE Disabled Interrupt is disabled 0 Enabled Interrupt is enabled 1 WCKCFGIE Wrong clock configuration interrupt enable 2 1 WCKCFGIE Disabled Interrupt is disabled 0 Enabled Interrupt is enabled 1 MUTEDETIE Mute detection interrupt enable 1 1 MUTEDETIE Disabled Interrupt is disabled 0 Enabled Interrupt is enabled 1 OVRUDRIE Overrun/underrun interrupt enable 0 1 OVRUDRIE Disabled Interrupt is disabled 0 Enabled Interrupt is enabled 1 SR ASR AStatus register 0x14 0x20 read-only 0x00000008 FLVL FIFO level threshold 16 3 FLVLR Empty FIFO empty 0 Quarter1 FIFO <= 1⁄4 but not empty 1 Quarter2 1⁄4 < FIFO <= 1⁄2 2 Quarter3 1⁄2 < FIFO <= 3⁄4 3 Quarter4 3⁄4 < FIFO but not full 4 Full FIFO full 5 LFSDET Late frame synchronization detection 6 1 LFSDETR NoError No error 0 NoSync Frame synchronization signal is not present at the right time 1 AFSDET Anticipated frame synchronization detection 5 1 AFSDETR NoError No error 0 EarlySync Frame synchronization signal is detected earlier than expected 1 CNRDY Codec not ready 4 1 CNRDYR Ready External AC’97 Codec is ready 0 NotReady External AC’97 Codec is not ready 1 FREQ FIFO request 3 1 FREQR NoRequest No FIFO request 0 Request FIFO request to read or to write the SAI_xDR 1 WCKCFG Wrong clock configuration flag. This bit is read only. 2 1 WCKCFGR Correct Clock configuration is correct 0 Wrong Clock configuration does not respect the rule concerning the frame length specification 1 MUTEDET Mute detection 1 1 MUTEDETR NoMute No MUTE detection on the SD input line 0 Mute MUTE value detected on the SD input line (0 value) for a specified number of consecutive audio frame 1 OVRUDR Overrun / underrun 0 1 OVRUDRR NoError No overrun/underrun error 0 Overrun Overrun/underrun error detection 1 CLRFR ACLRFR AClear flag register 0x18 0x20 write-only 0x00000000 CLFSDET Clear late frame synchronization detection flag 6 1 CLFSDETW Clear Clears the LFSDET flag 1 CAFSDET Clear anticipated frame synchronization detection flag. 5 1 CAFSDETW Clear Clears the AFSDET flag 1 CCNRDY Clear codec not ready flag 4 1 CCNRDYW Clear Clears the CNRDY flag 1 CWCKCFG Clear wrong clock configuration flag 2 1 CWCKCFGW Clear Clears the WCKCFG flag 1 CMUTEDET Mute detection flag 1 1 CMUTEDETW Clear Clears the MUTEDET flag 1 COVRUDR Clear overrun / underrun 0 1 COVRUDRW Clear Clears the OVRUDR flag 1 DR ADR AData register 0x1C 0x20 read-write 0x00000000 DATA Data 0 32 GCR GCR Global configuration register 0x0 0x20 read-write 0x00000000 SYNCIN Synchronization inputs 0 2 SYNCOUT Synchronization outputs 4 2 SAI2 0x40015C00 DMA2D DMA2D controller DMA2D 0x4002B000 0x0 0xC00 registers DMA2D DMA2D global interrupt 90 CR CR control register 0x0 0x20 read-write 0x00000000 MODE DMA2D mode 16 2 MODE MemoryToMemory Memory-to-memory (FG fetch only) 0 MemoryToMemoryPFC Memory-to-memory with PFC (FG fetch only with FG PFC active) 1 MemoryToMemoryPFCBlending Memory-to-memory with blending (FG and BG fetch with PFC and blending) 2 RegisterToMemory Register-to-memory 3 CEIE Configuration Error Interrupt Enable 13 1 CEIE Disabled CE interrupt disabled 0 Enabled CE interrupt enabled 1 CTCIE CLUT transfer complete interrupt enable 12 1 CTCIE Disabled CTC interrupt disabled 0 Enabled CTC interrupt enabled 1 CAEIE CLUT access error interrupt enable 11 1 CAEIE Disabled CAE interrupt disabled 0 Enabled CAE interrupt enabled 1 TWIE Transfer watermark interrupt enable 10 1 TWIE Disabled TW interrupt disabled 0 Enabled TW interrupt enabled 1 TCIE Transfer complete interrupt enable 9 1 TCIE Disabled TC interrupt disabled 0 Enabled TC interrupt enabled 1 TEIE Transfer error interrupt enable 8 1 TEIE Disabled TE interrupt disabled 0 Enabled TE interrupt enabled 1 ABORT Abort 2 1 ABORT AbortRequest Transfer abort requested 1 SUSP Suspend 1 1 SUSP NotSuspended Transfer not suspended 0 Suspended Transfer suspended 1 START Start 0 1 START Start Launch the DMA2D 1 ISR ISR Interrupt Status Register 0x4 0x20 read-only 0x00000000 CEIF Configuration error interrupt flag 5 1 CTCIF CLUT transfer complete interrupt flag 4 1 CAEIF CLUT access error interrupt flag 3 1 TWIF Transfer watermark interrupt flag 2 1 TCIF Transfer complete interrupt flag 1 1 TEIF Transfer error interrupt flag 0 1 IFCR IFCR interrupt flag clear register 0x8 0x20 read-write 0x00000000 CCEIF Clear configuration error interrupt flag 5 1 CCEIF Clear Clear the CEIF flag in the ISR register 1 CCTCIF Clear CLUT transfer complete interrupt flag 4 1 CCTCIF Clear Clear the CTCIF flag in the ISR register 1 CAECIF Clear CLUT access error interrupt flag 3 1 CAECIF Clear Clear the CAEIF flag in the ISR register 1 CTWIF Clear transfer watermark interrupt flag 2 1 CTWIF Clear Clear the TWIF flag in the ISR register 1 CTCIF Clear transfer complete interrupt flag 1 1 CTCIF Clear Clear the TCIF flag in the ISR register 1 CTEIF Clear Transfer error interrupt flag 0 1 CTEIF Clear Clear the TEIF flag in the ISR register 1 FGMAR FGMAR foreground memory address register 0xC 0x20 read-write 0x00000000 MA Memory address 0 32 FGOR FGOR foreground offset register 0x10 0x20 read-write 0x00000000 LO Line offset 0 14 0 16383 BGMAR BGMAR background memory address register 0x14 0x20 read-write 0x00000000 MA Memory address 0 32 BGOR BGOR background offset register 0x18 0x20 read-write 0x00000000 LO Line offset 0 14 0 16383 FGPFCCR FGPFCCR foreground PFC control register 0x1C 0x20 read-write 0x00000000 ALPHA Alpha value 24 8 0 255 AM Alpha mode 16 2 AM NoModify No modification of alpha channel 0 Replace Replace with value in ALPHA[7:0] 1 Multiply Multiply with value in ALPHA[7:0] 2 CS CLUT size 8 8 0 255 START Start 5 1 START Start Start the automatic loading of the CLUT 1 CCM CLUT color mode 4 1 CCM ARGB8888 CLUT color format ARGB8888 0 RGB888 CLUT color format RGB888 1 CM Color mode 0 4 CM ARGB8888 Color mode ARGB8888 0 RGB888 Color mode RGB888 1 RGB565 Color mode RGB565 2 ARGB1555 Color mode ARGB1555 3 ARGB4444 Color mode ARGB4444 4 L8 Color mode L8 5 AL44 Color mode AL44 6 AL88 Color mode AL88 7 L4 Color mode L4 8 A8 Color mode A8 9 A4 Color mode A4 10 FGCOLR FGCOLR foreground color register 0x20 0x20 read-write 0x00000000 RED Red Value 16 8 0 255 GREEN Green Value 8 8 0 255 BLUE Blue Value 0 8 0 255 BGPFCCR BGPFCCR background PFC control register 0x24 0x20 read-write 0x00000000 ALPHA Alpha value 24 8 0 255 AM Alpha mode 16 2 AM NoModify No modification of alpha channel 0 Replace Replace with value in ALPHA[7:0] 1 Multiply Multiply with value in ALPHA[7:0] 2 CS CLUT size 8 8 0 255 START Start 5 1 START Start Start the automatic loading of the CLUT 1 CCM CLUT Color mode 4 1 CCM ARGB8888 CLUT color format ARGB8888 0 RGB888 CLUT color format RGB888 1 CM Color mode 0 4 CM ARGB8888 Color mode ARGB8888 0 RGB888 Color mode RGB888 1 RGB565 Color mode RGB565 2 ARGB1555 Color mode ARGB1555 3 ARGB4444 Color mode ARGB4444 4 L8 Color mode L8 5 AL44 Color mode AL44 6 AL88 Color mode AL88 7 L4 Color mode L4 8 A8 Color mode A8 9 A4 Color mode A4 10 BGCOLR BGCOLR background color register 0x28 0x20 read-write 0x00000000 RED Red Value 16 8 0 255 GREEN Green Value 8 8 0 255 BLUE Blue Value 0 8 0 255 FGCMAR FGCMAR foreground CLUT memory address register 0x2C 0x20 read-write 0x00000000 MA Memory Address 0 32 BGCMAR BGCMAR background CLUT memory address register 0x30 0x20 read-write 0x00000000 MA Memory address 0 32 OPFCCR OPFCCR output PFC control register 0x34 0x20 read-write 0x00000000 CM Color mode 0 3 CM ARGB8888 ARGB8888 0 RGB888 RGB888 1 RGB565 RGB565 2 ARGB1555 ARGB1555 3 ARGB4444 ARGB4444 4 OCOLR OCOLR output color register 0x38 0x20 read-write 0x00000000 APLHA Alpha Channel Value 24 8 RED Red Value 16 8 GREEN Green Value 8 8 BLUE Blue Value 0 8 OMAR OMAR output memory address register 0x3C 0x20 read-write 0x00000000 MA Memory Address 0 32 OOR OOR output offset register 0x40 0x20 read-write 0x00000000 LO Line Offset 0 14 0 16383 NLR NLR number of line register 0x44 0x20 read-write 0x00000000 PL Pixel per lines 16 14 0 16383 NL Number of lines 0 16 0 65535 LWR LWR line watermark register 0x48 0x20 read-write 0x00000000 LW Line watermark 0 16 AMTCR AMTCR AHB master timer configuration register 0x4C 0x20 read-write 0x00000000 DT Dead Time 8 8 0 255 EN Enable 0 1 EN Disabled Disabled AHB/AXI dead-time functionality 0 Enabled Enabled AHB/AXI dead-time functionality 1 FGCLUT FGCLUT FGCLUT 0x400 0x20 read-write 0x00000000 APLHA APLHA 24 8 RED RED 16 8 GREEN GREEN 8 8 BLUE BLUE 0 8 BGCLUT BGCLUT BGCLUT 0x800 0x20 read-write 0x00000000 APLHA APLHA 24 8 RED RED 16 8 GREEN GREEN 8 8 BLUE BLUE 0 8 QUADSPI QuadSPI interface QUADSPI 0xA0001000 0x0 0x1000 registers CR CR control register 0x0 0x20 read-write 0x00000000 PRESCALER Clock prescaler 24 8 0 255 PMM Polling match mode 23 1 PMM AndMatch AND match mode. SMF is set if all the unmasked bits received from the Flash memory match the corresponding bits in the match register. 0 OrMatch OR match mode. SMF is set if any one of the unmasked bits received from the Flash memory matches its corresponding bit in the match register. 1 APMS Automatic poll mode stop 22 1 APMS NotStopOnMatch Automatic polling mode is stopped only by abort or by disabling the QUADSPI. 0 StopOnMatch Automatic polling mode stops as soon as there is a match. 1 TEIE Transfer error interrupt enable 16 1 TEIE Disabled Interrupt disable 0 Enabled Interrupt enabled 1 TOIE TimeOut interrupt enable 20 1 SMIE Status match interrupt enable 19 1 FTIE FIFO threshold interrupt enable 18 1 TCIE Transfer complete interrupt enable 17 1 FTHRES IFO threshold level 8 5 FSEL FLASH memory selection 7 1 FSEL SelectFlash1 FLASH 1 selected 0 SelectFlash2 FLASH 2 selected 1 DFM Dual-flash mode 6 1 DFM Disabled Dual-flash mode disabled 0 Enabled Dual-flash mode enabled 1 SSHIFT Sample shift 4 1 SSHIFT NoShift No shift 0 OneHalfCycleShift 1/2 cycle shift 1 TCEN Timeout counter enable 3 1 TCEN Disabled Timeout counter is disabled, and thus the chip select (nCS) remains active indefinitely after an access in memory-mapped mode. 0 Enabled Timeout counter is enabled, and thus the chip select is released in memory-mapped mode after TIMEOUT[15:0] cycles of Flash memory inactivity. 1 DMAEN DMA enable 2 1 DMAEN Disabled DMA is disabled for indirect mode 0 Enabled DMA is enabled for indirect mode 1 ABORT Abort request 1 1 ABORT NoAbortRequested No abort requested 0 AbortRequested Abort requested 1 EN Enable 0 1 EN Disabled QUADSPI is disabled 0 Enabled QUADSPI is enabled 1 DCR DCR device configuration register 0x4 0x20 read-write 0x00000000 FSIZE FLASH memory size 16 5 0 31 CSHT Chip select high time 8 3 0 7 CKMODE Mode 0 / mode 3 0 1 CKMODE Mode0 CLK must stay low while nCS is high (chip select released). This is referred to as mode 0. 0 Mode3 CLK must stay high while nCS is high (chip select released). This is referred to as mode 3. 1 SR SR status register 0x8 0x20 read-only 0x00000000 FLEVEL FIFO level 8 7 0 31 BUSY Busy 5 1 BUSY NotBusy 0 Busy 1 TOF Timeout flag 4 1 TOF NotTimeout 0 Timeout 1 SMF Status match flag 3 1 SMF NotMatched 0 Matched 1 FTF FIFO threshold flag 2 1 FTF NotReached 0 Reached 1 TCF Transfer complete flag 1 1 TCF NotComplete 0 Complete 1 TEF Transfer error flag 0 1 TEF NoError 0 Error 1 FCR FCR flag clear register 0xC 0x20 read-write 0x00000000 CTOF Clear timeout flag 4 1 CTOF Clear clears the TOF flag in the QUADSPI_SR register 1 CSMF Clear status match flag 3 1 CSMF Clear clears the SMF flag in the QUADSPI_SR register 1 CTCF Clear transfer complete flag 1 1 CTCF Clear clears the TCF flag in the QUADSPI_SR register 1 CTEF Clear transfer error flag 0 1 CTEF Clear clears the TEF flag in the QUADSPI_SR register 1 DLR DLR data length register 0x10 0x20 read-write 0x00000000 DL Data length 0 32 0 4294967295 CCR CCR communication configuration register 0x14 0x20 read-write 0x00000000 DDRM Double data rate mode 31 1 DDRM Disabled DDR Mode disabled 0 Enabled DDR Mode enabled 1 DHHC DDR hold half cycle 30 1 DHHC NoDelay Delay the data output using analog delay 0 Delayed Delay the data output by 1/4 of a QUADSPI output clock cycle. 1 SIOO Send instruction only once mode 28 1 SIOO SendEveryTransaction Send instruction on every transaction 0 SendFirstCommand Send instruction only for the first command 1 FMODE Functional mode 26 2 FMODE IndirectWrite Indirect write mode 0 IndirectRead Indirect read mode 1 AutomaticPolling Automatic polling mode 2 MemoryMapped Memory-mapped mode 3 DMODE Data mode 24 2 DMODE NoData No data 0 SingleLine Data on a single line 1 TwoLines Data on two lines 2 FourLines Data on four lines 3 DCYC Number of dummy cycles 18 5 0 31 ABSIZE Alternate bytes size 16 2 ABSIZE Bit8 8-bit alternate byte 0 Bit16 16-bit alternate bytes 1 Bit24 24-bit alternate bytes 2 Bit32 32-bit alternate bytes 3 ABMODE Alternate bytes mode 14 2 ABMODE NoAlternateBytes No alternate bytes 0 SingleLine Alternate bytes on a single line 1 TwoLines Alternate bytes on two lines 2 FourLines Alternate bytes on four lines 3 ADSIZE Address size 12 2 ADSIZE Bit8 8-bit address 0 Bit16 16-bit address 1 Bit24 24-bit address 2 Bit32 32-bit address 3 ADMODE Address mode 10 2 ADMODE NoAddress No address 0 SingleLine Address on a single line 1 TwoLines Address on two lines 2 FourLines Address on four lines 3 IMODE Instruction mode 8 2 IMODE NoInstruction No instruction 0 SingleLine Instruction on a single line 1 TwoLines Instruction on two lines 2 FourLines Instruction on four lines 3 INSTRUCTION Instruction 0 8 0 255 AR AR address register 0x18 0x20 read-write 0x00000000 ADDRESS Address 0 32 0 4294967295 ABR ABR ABR 0x1C 0x20 read-write 0x00000000 ALTERNATE ALTERNATE 0 32 0 4294967295 DR DR Data register: full word (32 bit) access 0x20 0x20 read-write 0x00000000 DATA Data 0 32 0 4294967295 DR16 Data register: half word (16 bit) access DR 0x20 0x10 DATA Data 0 16 0 65535 DR8 Data register: one byte (8 bit) access DR 0x20 0x8 DATA Data 0 8 0 255 PSMKR PSMKR polling status mask register 0x24 0x20 read-write 0x00000000 MASK Status mask 0 32 0 4294967295 PSMAR PSMAR polling status match register 0x28 0x20 read-write 0x00000000 MATCH Status match 0 32 0 4294967295 PIR PIR polling interval register 0x2C 0x20 read-write 0x00000000 INTERVAL Polling interval 0 16 0 65535 LPTR LPTR low-power timeout register 0x30 0x20 read-write 0x00000000 TIMEOUT Timeout period 0 16 0 65535 CEC HDMI-CEC controller CEC 0x40006C00 0x0 0x400 registers CR CR control register 0x0 0x20 read-write 0x00000000 TXEOM Tx End Of Message 2 1 TXSOM Tx start of message 1 1 CECEN CEC Enable 0 1 CFGR CFGR configuration register 0x4 0x20 read-write 0x00000000 SFT Signal Free Time 0 3 0 7 RXTOL Rx-Tolerance 3 1 BRESTP Rx-stop on bit rising error 4 1 BREGEN Generate error-bit on bit rising error 5 1 LBPEGEN Generate Error-Bit on Long Bit Period Error 6 1 BRDNOGEN Avoid Error-Bit Generation in Broadcast 7 1 SFTOP SFT Option Bit 8 1 OAR Own addresses configuration 16 15 0 32767 LSTN Listen mode 31 1 TXDR TXDR Tx data register 0x8 0x20 write-only 0x00000000 TXD Tx Data register 0 8 0 255 RXDR RXDR Rx Data Register 0xC 0x20 read-only 0x00000000 RXDR CEC Rx Data Register 0 8 ISR ISR Interrupt and Status Register 0x10 0x20 read-write 0x00000000 TXACKE Tx-Missing acknowledge error 12 1 TXERR Tx-Error 11 1 TXUDR Tx-Buffer Underrun 10 1 TXEND End of Transmission 9 1 TXBR Tx-Byte Request 8 1 ARBLST Arbitration Lost 7 1 RXACKE Rx-Missing Acknowledge 6 1 LBPE Rx-Long Bit Period Error 5 1 SBPE Rx-Short Bit period error 4 1 BRE Rx-Bit rising error 3 1 RXOVR Rx-Overrun 2 1 RXEND End Of Reception 1 1 RXBR Rx-Byte Received 0 1 IER IER interrupt enable register 0x14 0x20 read-write 0x00000000 TXACKIE Tx-Missing Acknowledge Error Interrupt Enable 12 1 TXERRIE Tx-Error Interrupt Enable 11 1 TXUDRIE Tx-Underrun interrupt enable 10 1 TXENDIE Tx-End of message interrupt enable 9 1 TXBRIE Tx-Byte Request Interrupt Enable 8 1 ARBLSTIE Arbitration Lost Interrupt Enable 7 1 RXACKIE Rx-Missing Acknowledge Error Interrupt Enable 6 1 LBPEIE Long Bit Period Error Interrupt Enable 5 1 SBPEIE Short Bit Period Error Interrupt Enable 4 1 BREIE Bit Rising Error Interrupt Enable 3 1 RXOVRIE Rx-Buffer Overrun Interrupt Enable 2 1 RXENDIE End Of Reception Interrupt Enable 1 1 RXBRIE Rx-Byte Received Interrupt Enable 0 1 SPDIFRX Receiver Interface SPDIF_RX 0x40004000 0x0 0x400 registers CR CR Control register 0x0 0x20 read-write 0x00000000 SPDIFEN Peripheral Block Enable 0 2 RXDMAEN Receiver DMA ENable for data flow 2 1 RXSTEO STerEO Mode 3 1 DRFMT RX Data format 4 2 PMSK Mask Parity error bit 6 1 VMSK Mask of Validity bit 7 1 CUMSK Mask of channel status and user bits 8 1 PTMSK Mask of Preamble Type bits 9 1 CBDMAEN Control Buffer DMA ENable for control flow 10 1 CHSEL Channel Selection 11 1 NBTR Maximum allowed re-tries during synchronization phase 12 2 WFA Wait For Activity 14 1 INSEL input selection 16 3 IMR IMR Interrupt mask register 0x4 0x20 read-write 0x00000000 RXNEIE RXNE interrupt enable 0 1 CSRNEIE Control Buffer Ready Interrupt Enable 1 1 PERRIE Parity error interrupt enable 2 1 OVRIE Overrun error Interrupt Enable 3 1 SBLKIE Synchronization Block Detected Interrupt Enable 4 1 SYNCDIE Synchronization Done 5 1 IFEIE Serial Interface Error Interrupt Enable 6 1 SR SR Status register 0x8 0x20 read-only 0x00000000 RXNE Read data register not empty 0 1 CSRNE Control Buffer register is not empty 1 1 PERR Parity error 2 1 OVR Overrun error 3 1 SBD Synchronization Block Detected 4 1 SYNCD Synchronization Done 5 1 FERR Framing error 6 1 SERR Synchronization error 7 1 TERR Time-out error 8 1 WIDTH5 Duration of 5 symbols counted with SPDIF_CLK 16 15 IFCR IFCR Interrupt Flag Clear register 0xC 0x20 write-only 0x00000000 PERRCF Clears the Parity error flag 2 1 OVRCF Clears the Overrun error flag 3 1 SBDCF Clears the Synchronization Block Detected flag 4 1 SYNCDCF Clears the Synchronization Done flag 5 1 DR DR Data input register 0x10 0x20 read-only 0x00000000 DR Parity Error bit 0 24 PE Parity Error bit 24 1 V Validity bit 25 1 U User bit 26 1 C Channel Status bit 27 1 PT Preamble Type 28 2 CSR CSR Channel Status register 0x14 0x20 read-only 0x00000000 USR User data information 0 16 CS Channel A status information 16 8 SOB Start Of Block 24 1 DIR DIR Debug Information register 0x18 0x20 read-only 0x00000000 THI Threshold HIGH 0 13 TLO Threshold LOW 16 13 SDMMC1 Secure digital input/output interface SDMMC 0x40012C00 0x0 0x400 registers SDMMC1 SDMMC1 global interrupt 49 POWER POWER power control register 0x0 0x20 read-write 0x00000000 PWRCTRL PWRCTRL 0 2 PWRCTRL PowerOff Power off 0 PowerOn Power on 3 CLKCR CLKCR SDI clock control register 0x4 0x20 read-write 0x00000000 HWFC_EN HW Flow Control enable 14 1 HWFC_EN Disabled HW Flow Control is disabled 0 Enabled HW Flow Control is enabled 1 NEGEDGE SDIO_CK dephasing selection bit 13 1 NEGEDGE Rising SDIO_CK generated on the rising edge 0 Falling SDIO_CK generated on the falling edge 1 WIDBUS Wide bus mode enable bit 11 2 WIDBUS BusWidth1 1 lane wide bus 0 BusWidth4 4 lane wide bus 1 BusWidth8 8 lane wide bus 2 BYPASS Clock divider bypass enable bit 10 1 BYPASS Disabled SDIOCLK is divided according to the CLKDIV value before driving the SDIO_CK output signal. 0 Enabled SDIOCLK directly drives the SDIO_CK output signal 1 PWRSAV Power saving configuration bit 9 1 PWRSAV Enabled SDIO_CK clock is always enabled 0 Disabled SDIO_CK is only enabled when the bus is active 1 CLKEN Clock enable bit 8 1 CLKEN Disabled Disable clock 0 Enabled Enable clock 1 CLKDIV Clock divide factor 0 8 0 255 ARG ARG argument register 0x8 0x20 read-write 0x00000000 CMDARG Command argument 0 32 0 4294967295 CMD CMD command register 0xC 0x20 read-write 0x00000000 SDIOSuspend SD I/O suspend command 11 1 SDIOSuspend Disabled Next command is not a SDIO suspend command 0 Enabled Next command send is a SDIO suspend command 1 CPSMEN Command path state machine (CPSM) Enable bit 10 1 CPSMEN Disabled Command path state machine disabled 0 Enabled Command path state machine enabled 1 WAITPEND CPSM Waits for ends of data transfer (CmdPend internal signal) 9 1 WAITPEND Disabled Don't wait for data end 0 Enabled Wait for end of data transfer signal before sending command 1 WAITINT CPSM waits for interrupt request 8 1 WAITINT Disabled Don't wait for interrupt request 0 Enabled Wait for interrupt request 1 WAITRESP Wait for response bits 6 2 WAITRESP NoResponse No response 0 ShortResponse Short response 1 NoResponse2 No reponse 2 LongResponse Long reponse 3 CMDINDEX Command index 0 6 0 63 RESPCMD RESPCMD command response register 0x10 0x20 read-only 0x00000000 RESPCMD Response command index 0 6 0 63 4 0x4 1-4 RESP%s RESP%s SDIO response %s register 0x14 0x20 read-only 0x00000000 CARDSTATUS Status of a card, which is part of the received response 0 32 0 4294967295 DTIMER DTIMER data timer register 0x24 0x20 read-write 0x00000000 DATATIME Data timeout period 0 32 0 4294967295 DLEN DLEN data length register 0x28 0x20 read-write 0x00000000 DATALENGTH Data length value 0 25 0 33554431 DCTRL DCTRL data control register 0x2C 0x20 read-write 0x00000000 SDIOEN SD I/O enable functions 11 1 SDIOEN Disabled SDIO operations disabled 0 Enabled SDIO operations enabled 1 RWMOD Read wait mode 10 1 RWMOD D2 Read wait control stopping using SDIO_D2 0 Ck Read wait control using SDIO_CK 1 RWSTOP Read wait stop 9 1 RWSTOP Disabled Read wait in progress if RWSTART is enabled 0 Enabled Enable for read wait stop if RWSTART is enabled 1 RWSTART Read wait start 8 1 RWSTART Disabled Don't start read wait operation 0 Enabled Read wait operation starts 1 DBLOCKSIZE Data block size 4 4 DMAEN DMA enable bit 3 1 DMAEN Disabled Dma disabled 0 Enabled Dma enabled 1 DTMODE Data transfer mode selection 1: Stream or SDIO multibyte data transfer 2 1 DTMODE BlockMode Bloack data transfer 0 StreamMode Stream or SDIO multibyte data transfer 1 DTDIR Data transfer direction selection 1 1 DTDIR ControllerToCard From controller to card 0 CardToController From card to controller 1 DTEN DTEN 0 1 DTEN Disabled Disabled 0 Enabled Start transfer 1 DCOUNT DCOUNT data counter register 0x30 0x20 read-only 0x00000000 DATACOUNT Data count value 0 25 0 33554431 STA STA status register 0x34 0x20 read-only 0x00000000 SDIOIT SDIO interrupt received 22 1 SDIOIT NotReceived SDIO interrupt not receieved 0 Received SDIO interrupt received 1 RXDAVL Data available in receive FIFO 21 1 RXDAVL NotAvailable Data not available in receive FIFO 0 Available Data available in receive FIFO 1 TXDAVL Data available in transmit FIFO 20 1 TXDAVL NotAvailable Data not available in transmit FIFO 0 Available Data available in transmit FIFO 1 RXFIFOE Receive FIFO empty 19 1 RXFIFOE NotEmpty Receive FIFO not empty 0 Empty Receive FIFO empty 1 TXFIFOE Transmit FIFO empty 18 1 TXFIFOE NotEmpty Transmit FIFO not empty 0 Empty Transmit FIFO empty. When HW Flow Control is enabled, TXFIFOE signals becomes activated when the FIFO contains 2 words. 1 RXFIFOF Receive FIFO full 17 1 RXFIFOF NotFull Transmit FIFO not full 0 Full Receive FIFO full. When HW Flow Control is enabled, RXFIFOF signals becomes activated 2 words before the FIFO is full. 1 TXFIFOF Transmit FIFO full 16 1 TXFIFOF NotFull Transmit FIFO not full 0 Full Transmit FIFO full 1 RXFIFOHF Receive FIFO half full: there are at least 8 words in the FIFO 15 1 RXFIFOHF NotHalfFull Receive FIFO not half full 0 HalfFull Receive FIFO half full. At least 8 words in the FIFO 1 TXFIFOHE Transmit FIFO half empty: at least 8 words can be written into the FIFO 14 1 TXFIFOHE NotHalfEmpty Transmit FIFO not half empty 0 HalfEmpty Transmit FIFO half empty. At least 8 words can be written into the FIFO 1 RXACT Data receive in progress 13 1 RXACT NotInProgress Data receive not in progress 0 InProgress Data receive in progress 1 TXACT Data transmit in progress 12 1 TXACT NotInProgress Data transmit is not in progress 0 InProgress Data transmit in progress 1 CMDACT Command transfer in progress 11 1 CMDACT NotInProgress Command transfer not in progress 0 InProgress Command tranfer in progress 1 DBCKEND Data block sent/received (CRC check passed) 10 1 DBCKEND NotTransferred Data block not sent/received (CRC check failed) 0 Transferred Data block sent/received (CRC check passed) 1 DATAEND Data end (data counter, SDIDCOUNT, is zero) 8 1 DATAEND NotDone Not done 0 Done Data end (DCOUNT, is zero) 1 CMDSENT Command sent (no response required) 7 1 CMDSENT NotSent Command not sent 0 Sent Command sent (no response required) 1 CMDREND Command response received (CRC check passed) 6 1 CMDREND NotDone Command not done 0 Done Command response received (CRC check passed) 1 RXOVERR Received FIFO overrun error 5 1 RXOVERR NoOverrun No FIFO overrun error 0 Overrun Receive FIFO overrun error 1 TXUNDERR Transmit FIFO underrun error 4 1 TXUNDERR NoUnderrun No transmit FIFO underrun error 0 Underrun Transmit FIFO underrun error 1 DTIMEOUT Data timeout 3 1 DTIMEOUT NoTimeout No data timeout 0 Timeout Data timeout 1 CTIMEOUT Command response timeout 2 1 CTIMEOUT NoTimeout No Command timeout 0 Timeout Command timeout 1 DCRCFAIL Data block sent/received (CRC check failed) 1 1 DCRCFAIL NotFailed No Data block sent/received crc check fail 0 Failed Data block sent/received crc failed 1 CCRCFAIL Command response received (CRC check failed) 0 1 CCRCFAIL NotFailed Command response received, crc check passed 0 Failed Command response received, crc check failed 1 ICR ICR interrupt clear register 0x38 0x20 read-write 0x00000000 CCRCFAILC CCRCFAIL flag clear bit 0 1 CCRCFAILCW write Clear Clear flag 1 SDIOITC SDIOIT flag clear bit 22 1 DBCKENDC DBCKEND flag clear bit 10 1 DATAENDC DATAEND flag clear bit 8 1 CMDSENTC CMDSENT flag clear bit 7 1 CMDRENDC CMDREND flag clear bit 6 1 RXOVERRC RXOVERR flag clear bit 5 1 TXUNDERRC TXUNDERR flag clear bit 4 1 DTIMEOUTC DTIMEOUT flag clear bit 3 1 CTIMEOUTC CTIMEOUT flag clear bit 2 1 DCRCFAILC DCRCFAIL flag clear bit 1 1 MASK MASK mask register 0x3C 0x20 read-write 0x00000000 CCRCFAILIE Command CRC fail interrupt enable 0 1 CCRCFAILIE Disabled Interrupt disabled 0 Enabled Interrupt enabled 1 SDIOITIE SDIO mode interrupt received interrupt enable 22 1 RXDAVLIE Data available in Rx FIFO interrupt enable 21 1 TXDAVLIE Data available in Tx FIFO interrupt enable 20 1 RXFIFOEIE Rx FIFO empty interrupt enable 19 1 TXFIFOEIE Tx FIFO empty interrupt enable 18 1 RXFIFOFIE Rx FIFO full interrupt enable 17 1 TXFIFOFIE Tx FIFO full interrupt enable 16 1 RXFIFOHFIE Rx FIFO half full interrupt enable 15 1 TXFIFOHEIE Tx FIFO half empty interrupt enable 14 1 RXACTIE Data receive acting interrupt enable 13 1 TXACTIE Data transmit acting interrupt enable 12 1 CMDACTIE Command acting interrupt enable 11 1 DBCKENDIE Data block end interrupt enable 10 1 DATAENDIE Data end interrupt enable 8 1 CMDSENTIE Command sent interrupt enable 7 1 CMDRENDIE Command response received interrupt enable 6 1 RXOVERRIE Rx FIFO overrun error interrupt enable 5 1 TXUNDERRIE Tx FIFO underrun error interrupt enable 4 1 DTIMEOUTIE Data timeout interrupt enable 3 1 CTIMEOUTIE Command timeout interrupt enable 2 1 DCRCFAILIE Data CRC fail interrupt enable 1 1 FIFOCNT FIFOCNT FIFO counter register 0x48 0x20 read-only 0x00000000 FIFOCOUNT Remaining number of words to be written to or read from the FIFO 0 24 0 16777215 FIFO FIFO data FIFO register 0x80 0x20 read-write 0x00000000 FIFOData Receive and transmit FIFO data 0 32 0 4294967295 LPTIM1 Low power timer LPTIM 0x40002400 0x0 0x400 registers ISR ISR Interrupt and Status Register 0x0 0x20 read-only 0x00000000 DOWN Counter direction change up to down 6 1 DOWNR Set Counter direction change up to down 1 UP Counter direction change down to up 5 1 UPR Set Counter direction change down to up 1 ARROK Autoreload register update OK 4 1 ARROKR Set Autoreload register update OK 1 CMPOK Compare register update OK 3 1 CMPOKR Set Compare register update OK 1 EXTTRIG External trigger edge event 2 1 EXTTRIGR Set External trigger edge event 1 ARRM Autoreload match 1 1 ARRMR Set Autoreload match 1 CMPM Compare match 0 1 CMPMR Set Compare match 1 ICR ICR Interrupt Clear Register 0x4 0x20 write-only 0x00000000 DOWNCF Direction change to down Clear Flag 6 1 DOWNCFW Clear Direction change to down Clear Flag 1 UPCF Direction change to UP Clear Flag 5 1 UPCFW Clear Direction change to up Clear Flag 1 ARROKCF Autoreload register update OK Clear Flag 4 1 ARROKCFW Clear Autoreload register update OK Clear Flag 1 CMPOKCF Compare register update OK Clear Flag 3 1 CMPOKCFW Clear Compare register update OK Clear Flag 1 EXTTRIGCF External trigger valid edge Clear Flag 2 1 EXTTRIGCFW Clear External trigger valid edge Clear Flag 1 ARRMCF Autoreload match Clear Flag 1 1 ARRMCFW Clear Autoreload match Clear Flag 1 CMPMCF compare match Clear Flag 0 1 CMPMCFW Clear Compare match Clear Flag 1 IER IER Interrupt Enable Register 0x8 0x20 read-write 0x00000000 DOWNIE Direction change to down Interrupt Enable 6 1 DOWNIE Disabled DOWN interrupt disabled 0 Enabled DOWN interrupt enabled 1 UPIE Direction change to UP Interrupt Enable 5 1 UPIE Disabled UP interrupt disabled 0 Enabled UP interrupt enabled 1 ARROKIE Autoreload register update OK Interrupt Enable 4 1 ARROKIE Disabled ARROK interrupt disabled 0 Enabled ARROK interrupt enabled 1 CMPOKIE Compare register update OK Interrupt Enable 3 1 CMPOKIE Disabled CMPOK interrupt disabled 0 Enabled CMPOK interrupt enabled 1 EXTTRIGIE External trigger valid edge Interrupt Enable 2 1 EXTTRIGIE Disabled EXTTRIG interrupt disabled 0 Enabled EXTTRIG interrupt enabled 1 ARRMIE Autoreload match Interrupt Enable 1 1 ARRMIE Disabled ARRM interrupt disabled 0 Enabled ARRM interrupt enabled 1 CMPMIE Compare match Interrupt Enable 0 1 CMPMIE Disabled CMPM interrupt disabled 0 Enabled CMPM interrupt enabled 1 CFGR CFGR Configuration Register 0xC 0x20 read-write 0x00000000 ENC Encoder mode enable 24 1 ENC Disabled Encoder mode disabled 0 Enabled Encoder mode enabled 1 COUNTMODE counter mode enabled 23 1 COUNTMODE Internal The counter is incremented following each internal clock pulse 0 External The counter is incremented following each valid clock pulse on the LPTIM external Input1 1 PRELOAD Registers update mode 22 1 PRELOAD Immediate Registers are updated after each APB bus write access 0 EndOfPeriod Registers are updated at the end of the current LPTIM period 1 WAVPOL Waveform shape polarity 21 1 WAVPOL Positive The LPTIM output reflects the compare results between LPTIM_ARR and LPTIM_CMP registers 0 Negative The LPTIM output reflects the inverse of the compare results between LPTIM_ARR and LPTIM_CMP registers 1 WAVE Waveform shape 20 1 WAVE Inactive Deactivate Set-once mode, PWM / One Pulse waveform (depending on OPMODE bit) 0 Active Activate the Set-once mode 1 TIMOUT Timeout enable 19 1 TIMOUT Disabled A trigger event arriving when the timer is already started will be ignored 0 Enabled A trigger event arriving when the timer is already started will reset and restart the counter 1 TRIGEN Trigger enable and polarity 17 2 TRIGEN SW Software trigger (counting start is initiated by software) 0 RisingEdge Rising edge is the active edge 1 FallingEdge Falling edge is the active edge 2 BothEdges Both edges are active edges 3 TRIGSEL Trigger selector 13 3 TRIGSEL Trig0 lptim_ext_trig0 0 Trig1 lptim_ext_trig1 1 Trig2 lptim_ext_trig2 2 Trig3 lptim_ext_trig3 3 Trig4 lptim_ext_trig4 4 Trig5 lptim_ext_trig5 5 Trig6 lptim_ext_trig6 6 Trig7 lptim_ext_trig7 7 PRESC Clock prescaler 9 3 PRESC Div1 /1 0 Div2 /2 1 Div4 /4 2 Div8 /8 3 Div16 /16 4 Div32 /32 5 Div64 /64 6 Div128 /128 7 TRGFLT Configurable digital filter for trigger 6 2 TRGFLT Immediate Any trigger active level change is considered as a valid trigger 0 Clocks2 Trigger active level change must be stable for at least 2 clock periods before it is considered as valid trigger 1 Clocks4 Trigger active level change must be stable for at least 4 clock periods before it is considered as valid trigger 2 Clocks8 Trigger active level change must be stable for at least 8 clock periods before it is considered as valid trigger 3 CKFLT Configurable digital filter for external clock 3 2 CKFLT Immediate Any external clock signal level change is considered as a valid transition 0 Clocks2 External clock signal level change must be stable for at least 2 clock periods before it is considered as valid transition 1 Clocks4 External clock signal level change must be stable for at least 4 clock periods before it is considered as valid transition 2 Clocks8 External clock signal level change must be stable for at least 8 clock periods before it is considered as valid transition 3 CKPOL Clock Polarity 1 2 CKPOL RisingEdge The rising edge is the active edge used for counting. If LPTIM is in encoder mode: Encoder sub-mode 1 is active. 0 FallingEdge The falling edge is the active edge used for counting. If LPTIM is in encoder mode: Encoder sub-mode 2 is active. 1 BothEdges Both edges are active edge. If LPTIM is in encoder mode: Encoder sub-mode 3 is active. 2 CKSEL Clock selector 0 1 CKSEL Internal LPTIM is clocked by internal clock source (APB clock or any of the embedded oscillators) 0 External LPTIM is clocked by an external clock source through the LPTIM external Input1 1 CR CR Control Register 0x10 0x20 read-write 0x00000000 CNTSTRT Timer start in continuous mode 2 1 CNTSTRTW write Start Timer start in Continuous mode 1 SNGSTRT LPTIM start in single mode 1 1 SNGSTRTW write Start LPTIM start in Single mode 1 ENABLE LPTIM Enable 0 1 ENABLE Disabled LPTIM is disabled 0 Enabled LPTIM is enabled 1 CMP CMP Compare Register 0x14 0x20 read-write 0x00000000 CMP Compare value 0 16 0 65535 ARR ARR Autoreload Register 0x18 0x20 read-write 0x00000001 ARR Auto reload value 0 16 0 65535 CNT CNT Counter Register 0x1C 0x20 read-only 0x00000000 CNT Counter value 0 16 0 65535 I2C1 Inter-integrated circuit I2C 0x40005400 0x0 0x400 registers I2C1_EV I2C1 event interrupt 31 I2C1_ER I2C1 error interrupt 32 CR1 CR1 Control register 1 0x0 0x20 read-write 0x00000000 PE Peripheral enable 0 1 PE Disabled Peripheral disabled 0 Enabled Peripheral enabled 1 TXIE TX Interrupt enable 1 1 TXIE Disabled Transmit (TXIS) interrupt disabled 0 Enabled Transmit (TXIS) interrupt enabled 1 RXIE RX Interrupt enable 2 1 RXIE Disabled Receive (RXNE) interrupt disabled 0 Enabled Receive (RXNE) interrupt enabled 1 ADDRIE Address match interrupt enable (slave only) 3 1 ADDRIE Disabled Address match (ADDR) interrupts disabled 0 Enabled Address match (ADDR) interrupts enabled 1 NACKIE Not acknowledge received interrupt enable 4 1 NACKIE Disabled Not acknowledge (NACKF) received interrupts disabled 0 Enabled Not acknowledge (NACKF) received interrupts enabled 1 STOPIE STOP detection Interrupt enable 5 1 STOPIE Disabled Stop detection (STOPF) interrupt disabled 0 Enabled Stop detection (STOPF) interrupt enabled 1 TCIE Transfer Complete interrupt enable 6 1 TCIE Disabled Transfer Complete interrupt disabled 0 Enabled Transfer Complete interrupt enabled 1 ERRIE Error interrupts enable 7 1 ERRIE Disabled Error detection interrupts disabled 0 Enabled Error detection interrupts enabled 1 DNF Digital noise filter 8 4 DNF NoFilter Digital filter disabled 0 Filter1 Digital filter enabled and filtering capability up to 1 tI2CCLK 1 Filter2 Digital filter enabled and filtering capability up to 2 tI2CCLK 2 Filter3 Digital filter enabled and filtering capability up to 3 tI2CCLK 3 Filter4 Digital filter enabled and filtering capability up to 4 tI2CCLK 4 Filter5 Digital filter enabled and filtering capability up to 5 tI2CCLK 5 Filter6 Digital filter enabled and filtering capability up to 6 tI2CCLK 6 Filter7 Digital filter enabled and filtering capability up to 7 tI2CCLK 7 Filter8 Digital filter enabled and filtering capability up to 8 tI2CCLK 8 Filter9 Digital filter enabled and filtering capability up to 9 tI2CCLK 9 Filter10 Digital filter enabled and filtering capability up to 10 tI2CCLK 10 Filter11 Digital filter enabled and filtering capability up to 11 tI2CCLK 11 Filter12 Digital filter enabled and filtering capability up to 12 tI2CCLK 12 Filter13 Digital filter enabled and filtering capability up to 13 tI2CCLK 13 Filter14 Digital filter enabled and filtering capability up to 14 tI2CCLK 14 Filter15 Digital filter enabled and filtering capability up to 15 tI2CCLK 15 ANFOFF Analog noise filter OFF 12 1 ANFOFF Enabled Analog noise filter enabled 0 Disabled Analog noise filter disabled 1 TXDMAEN DMA transmission requests enable 14 1 TXDMAEN Disabled DMA mode disabled for transmission 0 Enabled DMA mode enabled for transmission 1 RXDMAEN DMA reception requests enable 15 1 RXDMAEN Disabled DMA mode disabled for reception 0 Enabled DMA mode enabled for reception 1 SBC Slave byte control 16 1 SBC Disabled Slave byte control disabled 0 Enabled Slave byte control enabled 1 NOSTRETCH Clock stretching disable 17 1 NOSTRETCH Enabled Clock stretching enabled 0 Disabled Clock stretching disabled 1 WUPEN Wakeup from STOP enable 18 1 WUPEN Disabled Wakeup from Stop mode disabled 0 Enabled Wakeup from Stop mode enabled 1 GCEN General call enable 19 1 GCEN Disabled General call disabled. Address 0b00000000 is NACKed 0 Enabled General call enabled. Address 0b00000000 is ACKed 1 SMBHEN SMBus Host address enable 20 1 SMBHEN Disabled Host address disabled. Address 0b0001000x is NACKed 0 Enabled Host address enabled. Address 0b0001000x is ACKed 1 SMBDEN SMBus Device Default address enable 21 1 SMBDEN Disabled Device default address disabled. Address 0b1100001x is NACKed 0 Enabled Device default address enabled. Address 0b1100001x is ACKed 1 ALERTEN SMBUS alert enable 22 1 ALERTEN Disabled In device mode (SMBHEN=Disabled) Releases SMBA pin high and Alert Response Address Header disabled (0001100x) followed by NACK. In host mode (SMBHEN=Enabled) SMBus Alert pin (SMBA) not supported 0 Enabled In device mode (SMBHEN=Disabled) Drives SMBA pin low and Alert Response Address Header enabled (0001100x) followed by ACK.In host mode (SMBHEN=Enabled) SMBus Alert pin (SMBA) supported 1 PECEN PEC enable 23 1 PECEN Disabled PEC calculation disabled 0 Enabled PEC calculation enabled 1 CR2 CR2 Control register 2 0x4 0x20 read-write 0x00000000 PECBYTE Packet error checking byte 26 1 oneToSet PECBYTER read NoPec No PEC transfer 0 Pec PEC transmission/reception is requested 1 PECBYTEW write Pec PEC transmission/reception is requested 1 AUTOEND Automatic end mode (master mode) 25 1 AUTOEND Software Software end mode: TC flag is set when NBYTES data are transferred, stretching SCL low 0 Automatic Automatic end mode: a STOP condition is automatically sent when NBYTES data are transferred 1 RELOAD NBYTES reload mode 24 1 RELOAD Completed The transfer is completed after the NBYTES data transfer (STOP or RESTART will follow) 0 NotCompleted The transfer is not completed after the NBYTES data transfer (NBYTES will be reloaded) 1 NBYTES Number of bytes 16 8 0 255 NACK NACK generation (slave mode) 15 1 oneToSet NACKR read Ack an ACK is sent after current received byte 0 Nack a NACK is sent after current received byte 1 NACKW write Nack a NACK is sent after current received byte 1 STOP Stop generation (master mode) 14 1 oneToSet STOPR read NoStop No Stop generation 0 Stop Stop generation after current byte transfer 1 STOPW write Stop Stop generation after current byte transfer 1 START Start generation 13 1 oneToSet STARTR read NoStart No Start generation 0 Start Restart/Start generation 1 STARTW write Start Restart/Start generation 1 HEAD10R 10-bit address header only read direction (master receiver mode) 12 1 HEAD10R Complete The master sends the complete 10 bit slave address read sequence 0 Partial The master only sends the 1st 7 bits of the 10 bit address, followed by Read direction 1 ADD10 10-bit addressing mode (master mode) 11 1 ADD10 Bit7 The master operates in 7-bit addressing mode 0 Bit10 The master operates in 10-bit addressing mode 1 RD_WRN Transfer direction (master mode) 10 1 RD_WRN Write Master requests a write transfer 0 Read Master requests a read transfer 1 SADD Slave address bit (master mode) 0 10 0 1023 OAR1 OAR1 Own address register 1 0x8 0x20 read-write 0x00000000 OA1 Interface address 0 10 0 1023 OA1MODE Own Address 1 10-bit mode 10 1 OA1MODE Bit7 Own address 1 is a 7-bit address 0 Bit10 Own address 1 is a 10-bit address 1 OA1EN Own Address 1 enable 15 1 OA1EN Disabled Own address 1 disabled. The received slave address OA1 is NACKed 0 Enabled Own address 1 enabled. The received slave address OA1 is ACKed 1 OAR2 OAR2 Own address register 2 0xC 0x20 read-write 0x00000000 OA2 Interface address 1 7 0 127 OA2MSK Own Address 2 masks 8 3 OA2MSK NoMask No mask 0 Mask1 OA2[1] is masked and don’t care. Only OA2[7:2] are compared 1 Mask2 OA2[2:1] are masked and don’t care. Only OA2[7:3] are compared 2 Mask3 OA2[3:1] are masked and don’t care. Only OA2[7:4] are compared 3 Mask4 OA2[4:1] are masked and don’t care. Only OA2[7:5] are compared 4 Mask5 OA2[5:1] are masked and don’t care. Only OA2[7:6] are compared 5 Mask6 OA2[6:1] are masked and don’t care. Only OA2[7] is compared. 6 Mask7 OA2[7:1] are masked and don’t care. No comparison is done, and all (except reserved) 7-bit received addresses are acknowledged 7 OA2EN Own Address 2 enable 15 1 OA2EN Disabled Own address 2 disabled. The received slave address OA2 is NACKed 0 Enabled Own address 2 enabled. The received slave address OA2 is ACKed 1 TIMINGR TIMINGR Timing register 0x10 0x20 read-write 0x00000000 SCLL SCL low period (master mode) 0 8 0 255 SCLH SCL high period (master mode) 8 8 0 255 SDADEL Data hold time 16 4 0 15 SCLDEL Data setup time 20 4 0 15 PRESC Timing prescaler 28 4 0 15 TIMEOUTR TIMEOUTR Status register 1 0x14 0x20 read-write 0x00000000 TIMEOUTA Bus timeout A 0 12 0 4095 TIDLE Idle clock timeout detection 12 1 TIDLE Disabled TIMEOUTA is used to detect SCL low timeout 0 Enabled TIMEOUTA is used to detect both SCL and SDA high timeout (bus idle condition) 1 TIMOUTEN Clock timeout enable 15 1 TIMOUTEN Disabled SCL timeout detection is disabled 0 Enabled SCL timeout detection is enabled 1 TIMEOUTB Bus timeout B 16 12 0 4095 TEXTEN Extended clock timeout enable 31 1 TEXTEN Disabled Extended clock timeout detection is disabled 0 Enabled Extended clock timeout detection is enabled 1 ISR ISR Interrupt and Status register 0x18 0x20 0x00000001 ADDCODE Address match code (Slave mode) 17 7 read-only 0 127 DIR Transfer direction (Slave mode) 16 1 read-only DIR Write Write transfer, slave enters receiver mode 0 Read Read transfer, slave enters transmitter mode 1 BUSY Bus busy 15 1 read-only BUSY NotBusy No communication is in progress on the bus 0 Busy A communication is in progress on the bus 1 ALERT SMBus alert 13 1 read-only ALERT NoAlert SMBA alert is not detected 0 Alert SMBA alert event is detected on SMBA pin 1 TIMEOUT Timeout or t_low detection flag 12 1 read-only TIMEOUT NoTimeout No timeout occured 0 Timeout Timeout occured 1 PECERR PEC Error in reception 11 1 read-only PECERR Match Received PEC does match with PEC register 0 NoMatch Received PEC does not match with PEC register 1 OVR Overrun/Underrun (slave mode) 10 1 read-only OVR NoOverrun No overrun/underrun error occurs 0 Overrun slave mode with NOSTRETCH=1, when an overrun/underrun error occurs 1 ARLO Arbitration lost 9 1 read-only ARLO NotLost No arbitration lost 0 Lost Arbitration lost 1 BERR Bus error 8 1 read-only BERR NoError No bus error 0 Error Misplaced Start and Stop condition is detected 1 TCR Transfer Complete Reload 7 1 read-only TCR NotComplete Transfer is not complete 0 Complete NBYTES has been transfered 1 TC Transfer Complete (master mode) 6 1 read-only TC NotComplete Transfer is not complete 0 Complete NBYTES has been transfered 1 STOPF Stop detection flag 5 1 read-only STOPF NoStop No Stop condition detected 0 Stop Stop condition detected 1 NACKF Not acknowledge received flag 4 1 read-only NACKF NoNack No NACK has been received 0 Nack NACK has been received 1 ADDR Address matched (slave mode) 3 1 read-only ADDR NotMatch Adress mismatched or not received 0 Match Received slave address matched with one of the enabled slave addresses 1 RXNE Receive data register not empty (receivers) 2 1 read-only RXNE Empty The RXDR register is empty 0 NotEmpty Received data is copied into the RXDR register, and is ready to be read 1 TXIS Transmit interrupt status (transmitters) 1 1 read-write oneToSet TXISR read NotEmpty The TXDR register is not empty 0 Empty The TXDR register is empty and the data to be transmitted must be written in the TXDR register 1 TXISW write Trigger Generate a TXIS event 1 TXE Transmit data register empty (transmitters) 0 1 read-write oneToSet TXER read NotEmpty TXDR register not empty 0 Empty TXDR register empty 1 TXEW write Flush Flush the transmit data register 1 ICR ICR Interrupt clear register 0x1C 0x20 write-only 0x00000000 ALERTCF Alert flag clear 13 1 oneToClear ALERTCF Clear Clears the ALERT flag in ISR register 1 TIMOUTCF Timeout detection flag clear 12 1 oneToClear TIMOUTCF Clear Clears the TIMOUT flag in ISR register 1 PECCF PEC Error flag clear 11 1 oneToClear PECCF Clear Clears the PEC flag in ISR register 1 OVRCF Overrun/Underrun flag clear 10 1 oneToClear OVRCF Clear Clears the OVR flag in ISR register 1 ARLOCF Arbitration lost flag clear 9 1 oneToClear ARLOCF Clear Clears the ARLO flag in ISR register 1 BERRCF Bus error flag clear 8 1 oneToClear BERRCF Clear Clears the BERR flag in ISR register 1 STOPCF Stop detection flag clear 5 1 oneToClear STOPCF Clear Clears the STOP flag in ISR register 1 NACKCF Not Acknowledge flag clear 4 1 oneToClear NACKCF Clear Clears the NACK flag in ISR register 1 ADDRCF Address Matched flag clear 3 1 oneToClear ADDRCF Clear Clears the ADDR flag in ISR register 1 PECR PECR PEC register 0x20 0x20 read-only 0x00000000 PEC Packet error checking register 0 8 0 255 RXDR RXDR Receive data register 0x24 0x20 read-only 0x00000000 RXDATA 8-bit receive data 0 8 0 255 TXDR TXDR Transmit data register 0x28 0x20 read-write 0x00000000 TXDATA 8-bit transmit data 0 8 0 255 I2C2 0x40005800 I2C3 0x40005C00 I2C4 0x40006000 RTC Real-time clock RTC 0x40002800 0x0 0x400 registers RTC_WKUP RTC Tamper or TimeStamp /CSS on LSE through EXTI line 19 interrupts 3 RTC_ALARM RTC alarms through EXTI line 18 interrupts 41 TR TR time register 0x0 0x20 read-write 0x00000000 PM AM/PM notation 22 1 PM AM AM or 24-hour format 0 PM PM 1 HT Hour tens in BCD format 20 2 0 3 HU Hour units in BCD format 16 4 0 15 MNT Minute tens in BCD format 12 3 0 7 MNU Minute units in BCD format 8 4 0 15 ST Second tens in BCD format 4 3 0 7 SU Second units in BCD format 0 4 0 15 DR DR date register 0x4 0x20 read-write 0x00002101 YT Year tens in BCD format 20 4 0 15 YU Year units in BCD format 16 4 0 15 WDU Week day units 13 3 1 7 MT Month tens in BCD format 12 1 MT Zero Month tens is 0 0 One Month tens is 1 1 MU Month units in BCD format 8 4 0 15 DT Date tens in BCD format 4 2 0 3 DU Date units in BCD format 0 4 0 15 CR CR control register 0x8 0x20 read-write 0x00000000 WUCKSEL Wakeup clock selection 0 3 WUCKSEL Div16 RTC/16 clock is selected 0 Div8 RTC/8 clock is selected 1 Div4 RTC/4 clock is selected 2 Div2 RTC/2 clock is selected 3 ClockSpare ck_spre (usually 1 Hz) clock is selected 4 ClockSpareWithOffset ck_spre (usually 1 Hz) clock is selected and 2^16 is added to the WUT counter value 6 TSEDGE Time-stamp event active edge 3 1 TSEDGE RisingEdge RTC_TS input rising edge generates a time-stamp event 0 FallingEdge RTC_TS input falling edge generates a time-stamp event 1 REFCKON Reference clock detection enable (50 or 60 Hz) 4 1 REFCKON Disabled RTC_REFIN detection disabled 0 Enabled RTC_REFIN detection enabled 1 BYPSHAD Bypass the shadow registers 5 1 BYPSHAD ShadowReg Calendar values (when reading from RTC_SSR, RTC_TR, and RTC_DR) are taken from the shadow registers, which are updated once every two RTCCLK cycles 0 BypassShadowReg Calendar values (when reading from RTC_SSR, RTC_TR, and RTC_DR) are taken directly from the calendar counters 1 FMT Hour format 6 1 FMT Twenty_Four_Hour 24 hour/day format 0 AM_PM AM/PM hour format 1 2 0x1 A,B ALR%sE Alarm %s enable 8 1 ALRAE Disabled Alarm disabled 0 Enabled Alarm enabled 1 WUTE Wakeup timer enable 10 1 WUTE Disabled Wakeup timer disabled 0 Enabled Wakeup timer enabled 1 TSE Time stamp enable 11 1 TSE Disabled Timestamp disabled 0 Enabled Timestamp enabled 1 2 0x1 A,B ALR%sIE Alarm %s interrupt enable 12 1 ALRAIE Disabled Alarm Interrupt disabled 0 Enabled Alarm Interrupt enabled 1 WUTIE Wakeup timer interrupt enable 14 1 WUTIE Disabled Wakeup timer interrupt disabled 0 Enabled Wakeup timer interrupt enabled 1 TSIE Time-stamp interrupt enable 15 1 TSIE Disabled Time-stamp Interrupt disabled 0 Enabled Time-stamp Interrupt enabled 1 ADD1H Add 1 hour (summer time change) 16 1 ADD1HW write Add1 Adds 1 hour to the current time. This can be used for summer time change outside initialization mode 1 SUB1H Subtract 1 hour (winter time change) 17 1 SUB1HW write Sub1 Subtracts 1 hour to the current time. This can be used for winter time change outside initialization mode 1 BKP Backup 18 1 BKP DST_Not_Changed Daylight Saving Time change has not been performed 0 DST_Changed Daylight Saving Time change has been performed 1 COSEL Calibration output selection 19 1 COSEL CalFreq_512Hz Calibration output is 512 Hz (with default prescaler setting) 0 CalFreq_1Hz Calibration output is 1 Hz (with default prescaler setting) 1 POL Output polarity 20 1 POL High The pin is high when ALRAF/ALRBF/WUTF is asserted (depending on OSEL[1:0]) 0 Low The pin is low when ALRAF/ALRBF/WUTF is asserted (depending on OSEL[1:0]) 1 OSEL Output selection 21 2 OSEL Disabled Output disabled 0 AlarmA Alarm A output enabled 1 AlarmB Alarm B output enabled 2 Wakeup Wakeup output enabled 3 COE Calibration output enable 23 1 COE Disabled Calibration output disabled 0 Enabled Calibration output enabled 1 ITSE timestamp on internal event enable 24 1 ISR ISR initialization and status register 0xC 0x20 0x00000007 2 0x1 A,B ALR%sWF Alarm %s write flag 0 1 read-only ALRAWFR UpdateNotAllowed Alarm update not allowed 0 UpdateAllowed Alarm update allowed 1 WUTWF Wakeup timer write flag 2 1 read-only WUTWFR UpdateNotAllowed Wakeup timer configuration update not allowed 0 UpdateAllowed Wakeup timer configuration update allowed 1 SHPF Shift operation pending 3 1 read-write SHPFR read NoShiftPending No shift operation is pending 0 ShiftPending A shift operation is pending 1 INITS Initialization status flag 4 1 read-only INITSR NotInitalized Calendar has not been initialized 0 Initalized Calendar has been initialized 1 RSF Registers synchronization flag 5 1 read-write zeroToClear RSFR read NotSynced Calendar shadow registers not yet synchronized 0 Synced Calendar shadow registers synchronized 1 RSFW write Clear This flag is cleared by software by writing 0 0 INITF Initialization flag 6 1 read-only INITFR NotAllowed Calendar registers update is not allowed 0 Allowed Calendar registers update is allowed 1 INIT Initialization mode 7 1 read-write INIT FreeRunningMode Free running mode 0 InitMode Initialization mode used to program time and date register (RTC_TR and RTC_DR), and prescaler register (RTC_PRER). Counters are stopped and start counting from the new value when INIT is reset. 1 2 0x1 A,B ALR%sF Alarm %s flag 8 1 read-write zeroToClear ALRAFR read Match This flag is set by hardware when the time/date registers (RTC_TR and RTC_DR) match the Alarm register (RTC_ALRMxR) 1 ALRAFW write Clear This flag is cleared by software by writing 0 0 WUTF Wakeup timer flag 10 1 read-write zeroToClear WUTFR read Zero This flag is set by hardware when the wakeup auto-reload counter reaches 0 1 WUTFW write Clear This flag is cleared by software by writing 0 0 TSF Time-stamp flag 11 1 read-write zeroToClear TSFR read TimestampEvent This flag is set by hardware when a time-stamp event occurs 1 TSFW write Clear This flag is cleared by software by writing 0 0 TSOVF Time-stamp overflow flag 12 1 read-write zeroToClear TSOVFR read Overflow This flag is set by hardware when a time-stamp event occurs while TSF is already set 1 TSOVFW write Clear This flag is cleared by software by writing 0 0 TAMP1F Tamper detection flag 13 1 read-write zeroToClear TAMP1FR read Tampered This flag is set by hardware when a tamper detection event is detected on the RTC_TAMPx input 1 TAMP1FW write Clear Flag cleared by software writing 0 0 TAMP2F RTC_TAMP2 detection flag 14 1 read-write zeroToClear read write TAMP3F RTC_TAMP3 detection flag 15 1 read-write zeroToClear read write RECALPF Recalibration pending Flag 16 1 read-only RECALPFR Pending The RECALPF status flag is automatically set to 1 when software writes to the RTC_CALR register, indicating that the RTC_CALR register is blocked. When the new calibration settings are taken into account, this bit returns to 0 1 PRER PRER prescaler register 0x10 0x20 read-write 0x007F00FF PREDIV_A Asynchronous prescaler factor 16 7 0 127 PREDIV_S Synchronous prescaler factor 0 15 0 32767 WUTR WUTR wakeup timer register 0x14 0x20 read-write 0x0000FFFF WUT Wakeup auto-reload value bits 0 16 0 65535 2 0x4 A,B ALRM%sR ALRM%sR Alarm %s register 0x1C 0x20 read-write 0x00000000 MSK1 Alarm seconds mask 7 1 MSK1 Mask Alarm set if the date/day match 0 NotMask Date/day don’t care in Alarm comparison 1 MSK4 Alarm date mask 31 1 WDSEL Week day selection 30 1 WDSEL DateUnits DU[3:0] represents the date units 0 WeekDay DU[3:0] represents the week day. DT[1:0] is don’t care. 1 DT Date tens in BCD format 28 2 0 3 DU Date units or day in BCD format 24 4 0 15 MSK3 Alarm hours mask 23 1 PM AM/PM notation 22 1 PM AM AM or 24-hour format 0 PM PM 1 HT Hour tens in BCD format 20 2 0 3 HU Hour units in BCD format 16 4 0 15 MSK2 Alarm minutes mask 15 1 MNT Minute tens in BCD format 12 3 0 7 MNU Minute units in BCD format 8 4 0 15 ST Second tens in BCD format 4 3 0 7 SU Second units in BCD format 0 4 0 15 WPR WPR write protection register 0x24 0x20 write-only 0x00000000 KEY Write protection key 0 8 0 255 SSR SSR sub second register 0x28 0x20 read-only 0x00000000 SS Sub second value 0 16 0 65535 SHIFTR SHIFTR shift control register 0x2C 0x20 write-only 0x00000000 ADD1S Add one second 31 1 ADD1SW Add1 Add one second to the clock/calendar 1 SUBFS Subtract a fraction of a second 0 15 0 32767 TSTR TSTR time stamp time register 0x30 TSDR TSDR time stamp date register 0x34 TSSSR TSSSR timestamp sub second register 0x38 CALR CALR calibration register 0x3C 0x20 read-write 0x00000000 CALP Increase frequency of RTC by 488.5 ppm 15 1 CALP NoChange No RTCCLK pulses are added 0 IncreaseFreq One RTCCLK pulse is effectively inserted every 2^11 pulses (frequency increased by 488.5 ppm) 1 CALW8 Use an 8-second calibration cycle period 14 1 CALW8 Eight_Second When CALW8 is set to ‘1’, the 8-second calibration cycle period is selected 1 CALW16 Use a 16-second calibration cycle period 13 1 CALW16 Sixteen_Second When CALW16 is set to ‘1’, the 16-second calibration cycle period is selected.This bit must not be set to ‘1’ if CALW8=1 1 CALM Calibration minus 0 9 0 511 TAMPCR TAMPCR tamper configuration register 0x40 0x20 read-write 0x00000000 TAMP1E Tamper 1 detection enable 0 1 TAMP1TRG Active level for tamper 1 1 1 TAMPIE Tamper interrupt enable 2 1 TAMP2E Tamper 2 detection enable 3 1 TAMP2TRG Active level for tamper 2 4 1 TAMP3E Tamper 3 detection enable 5 1 TAMP3TRG Active level for tamper 3 6 1 TAMPTS Activate timestamp on tamper detection event 7 1 TAMPFREQ Tamper sampling frequency 8 3 TAMPFLT Tamper filter count 11 2 TAMPPRCH Tamper precharge duration 13 2 TAMPPUDIS TAMPER pull-up disable 15 1 TAMP1IE Tamper 1 interrupt enable 16 1 TAMP1NOERASE Tamper 1 no erase 17 1 TAMP1MF Tamper 1 mask flag 18 1 TAMP2IE Tamper 2 interrupt enable 19 1 TAMP2NOERASE Tamper 2 no erase 20 1 TAMP2MF Tamper 2 mask flag 21 1 TAMP3IE Tamper 3 interrupt enable 22 1 TAMP3NOERASE Tamper 3 no erase 23 1 TAMP3MF Tamper 3 mask flag 24 1 2 0x4 A,B ALRM%sSSR ALRM%sSSR Alarm %s sub-second register 0x44 0x20 read-write 0x00000000 MASKSS Mask the most-significant bits starting at this bit 24 4 0 15 SS Sub seconds value 0 15 0 32767 OR OR option register 0x4C 0x20 read-write 0x00000000 RTC_ALARM_TYPE RTC_ALARM on PC13 output type 0 1 RTC_OUT_RMP RTC_OUT remap 1 1 32 0x4 0-31 BKP%sR BKP%sR backup register 0x50 0x20 read-write 0x00000000 BKP BKP 0 32 0 4294967295 USART1 Universal synchronous asynchronous receiver transmitter USART 0x40011000 0x0 0x400 registers USART1 USART1 global interrupt 37 CR1 CR1 Control register 1 0x0 0x20 read-write 0x00000000 M1 Word length 28 1 M1 M0 Use M0 to set the data bits 0 Bit7 1 start bit, 7 data bits, n stop bits 1 EOBIE End of Block interrupt enable 27 1 EOBIE Disabled Interrupt is inhibited 0 Enabled A USART interrupt is generated when the EOBF flag is set in the ISR register 1 RTOIE Receiver timeout interrupt enable 26 1 RTOIE Disabled Interrupt is inhibited 0 Enabled An USART interrupt is generated when the RTOF bit is set in the ISR register 1 DEAT Driver Enable assertion time 21 5 0 31 DEDT Driver Enable de-assertion time 16 5 0 31 OVER8 Oversampling mode 15 1 OVER8 Oversampling16 Oversampling by 16 0 Oversampling8 Oversampling by 8 1 CMIE Character match interrupt enable 14 1 CMIE Disabled Interrupt is disabled 0 Enabled Interrupt is generated when the CMF bit is set in the ISR register 1 MME Mute mode enable 13 1 MME Disabled Receiver in active mode permanently 0 Enabled Receiver can switch between mute mode and active mode 1 M0 Word length 12 1 M0 Bit8 1 start bit, 8 data bits, n stop bits 0 Bit9 1 start bit, 9 data bits, n stop bits 1 WAKE Receiver wakeup method 11 1 WAKE Idle Idle line 0 Address Address mask 1 PCE Parity control enable 10 1 PCE Disabled Parity control disabled 0 Enabled Parity control enabled 1 PS Parity selection 9 1 PS Even Even parity 0 Odd Odd parity 1 PEIE PE interrupt enable 8 1 PEIE Disabled Interrupt is disabled 0 Enabled Interrupt is generated whenever PE=1 in the ISR register 1 TXEIE interrupt enable 7 1 TXEIE Disabled Interrupt is disabled 0 Enabled Interrupt is generated whenever TXE=1 in the ISR register 1 TCIE Transmission complete interrupt enable 6 1 TCIE Disabled Interrupt is disabled 0 Enabled Interrupt is generated whenever TC=1 in the ISR register 1 RXNEIE RXNE interrupt enable 5 1 RXNEIE Disabled Interrupt is disabled 0 Enabled Interrupt is generated whenever ORE=1 or RXNE=1 in the ISR register 1 IDLEIE IDLE interrupt enable 4 1 IDLEIE Disabled Interrupt is disabled 0 Enabled Interrupt is generated whenever IDLE=1 in the ISR register 1 TE Transmitter enable 3 1 TE Disabled Transmitter is disabled 0 Enabled Transmitter is enabled 1 RE Receiver enable 2 1 RE Disabled Receiver is disabled 0 Enabled Receiver is enabled 1 UESM USART enable in Stop mode 1 1 UESM Disabled USART not able to wake up the MCU from Stop mode 0 Enabled USART able to wake up the MCU from Stop mode 1 UE USART enable 0 1 UE Disabled UART is disabled 0 Enabled UART is enabled 1 CR2 CR2 Control register 2 0x4 0x20 read-write 0x00000000 ADD Address of the USART node 24 8 0 255 RTOEN Receiver timeout enable 23 1 RTOEN Disabled Receiver timeout feature disabled 0 Enabled Receiver timeout feature enabled 1 ABRMOD Auto baud rate mode 21 2 ABRMOD Start Measurement of the start bit is used to detect the baud rate 0 Edge Falling edge to falling edge measurement 1 Frame7F 0x7F frame detection 2 Frame55 0x55 frame detection 3 ABREN Auto baud rate enable 20 1 ABREN Disabled Auto baud rate detection is disabled 0 Enabled Auto baud rate detection is enabled 1 MSBFIRST Most significant bit first 19 1 MSBFIRST LSB data is transmitted/received with data bit 0 first, following the start bit 0 MSB data is transmitted/received with MSB (bit 7/8/9) first, following the start bit 1 DATAINV Binary data inversion 18 1 DATAINV Positive Logical data from the data register are send/received in positive/direct logic 0 Negative Logical data from the data register are send/received in negative/inverse logic 1 TXINV TX pin active level inversion 17 1 TXINV Standard TX pin signal works using the standard logic levels 0 Inverted TX pin signal values are inverted 1 RXINV RX pin active level inversion 16 1 RXINV Standard RX pin signal works using the standard logic levels 0 Inverted RX pin signal values are inverted 1 SWAP Swap TX/RX pins 15 1 SWAP Standard TX/RX pins are used as defined in standard pinout 0 Swapped The TX and RX pins functions are swapped 1 LINEN LIN mode enable 14 1 LINEN Disabled LIN mode disabled 0 Enabled LIN mode enabled 1 STOP STOP bits 12 2 STOP Stop1 1 stop bit 0 Stop0p5 0.5 stop bit 1 Stop2 2 stop bit 2 Stop1p5 1.5 stop bit 3 CLKEN Clock enable 11 1 CLKEN Disabled CK pin disabled 0 Enabled CK pin enabled 1 CPOL Clock polarity 10 1 CPOL Low Steady low value on CK pin outside transmission window 0 High Steady high value on CK pin outside transmission window 1 CPHA Clock phase 9 1 CPHA First The first clock transition is the first data capture edge 0 Second The second clock transition is the first data capture edge 1 LBCL Last bit clock pulse 8 1 LBCL NotOutput The clock pulse of the last data bit is not output to the CK pin 0 Output The clock pulse of the last data bit is output to the CK pin 1 LBDIE LIN break detection interrupt enable 6 1 LBDIE Disabled Interrupt is inhibited 0 Enabled An interrupt is generated whenever LBDF=1 in the ISR register 1 LBDL LIN break detection length 5 1 LBDL Bit10 10-bit break detection 0 Bit11 11-bit break detection 1 ADDM7 7-bit Address Detection/4-bit Address Detection 4 1 ADDM7 Bit4 4-bit address detection 0 Bit7 7-bit address detection 1 CR3 CR3 Control register 3 0x8 0x20 read-write 0x00000000 WUFIE Wakeup from Stop mode interrupt enable 22 1 WUFIE Disabled Interrupt is inhibited 0 Enabled An USART interrupt is generated whenever WUF=1 in the ISR register 1 WUS Wakeup from Stop mode interrupt flag selection 20 2 WUS Address WUF active on address match 0 Start WuF active on Start bit detection 2 RXNE WUF active on RXNE 3 SCARCNT Smartcard auto-retry count 17 3 0 7 DEP Driver enable polarity selection 15 1 DEP High DE signal is active high 0 Low DE signal is active low 1 DEM Driver enable mode 14 1 DEM Disabled DE function is disabled 0 Enabled The DE signal is output on the RTS pin 1 DDRE DMA Disable on Reception Error 13 1 DDRE NotDisabled DMA is not disabled in case of reception error 0 Disabled DMA is disabled following a reception error 1 OVRDIS Overrun Disable 12 1 OVRDIS Enabled Overrun Error Flag, ORE, is set when received data is not read before receiving new data 0 Disabled Overrun functionality is disabled. If new data is received while the RXNE flag is still set the ORE flag is not set and the new received data overwrites the previous content of the RDR register 1 ONEBIT One sample bit method enable 11 1 ONEBIT Sample3 Three sample bit method 0 Sample1 One sample bit method 1 CTSIE CTS interrupt enable 10 1 CTSIE Disabled Interrupt is inhibited 0 Enabled An interrupt is generated whenever CTSIF=1 in the ISR register 1 CTSE CTS enable 9 1 CTSE Disabled CTS hardware flow control disabled 0 Enabled CTS mode enabled, data is only transmitted when the CTS input is asserted 1 RTSE RTS enable 8 1 RTSE Disabled RTS hardware flow control disabled 0 Enabled RTS output enabled, data is only requested when there is space in the receive buffer 1 DMAT DMA enable transmitter 7 1 DMAT Disabled DMA mode is disabled for transmission 0 Enabled DMA mode is enabled for transmission 1 DMAR DMA enable receiver 6 1 DMAR Disabled DMA mode is disabled for reception 0 Enabled DMA mode is enabled for reception 1 SCEN Smartcard mode enable 5 1 SCEN Disabled Smartcard Mode disabled 0 Enabled Smartcard Mode enabled 1 NACK Smartcard NACK enable 4 1 NACK Disabled NACK transmission in case of parity error is disabled 0 Enabled NACK transmission during parity error is enabled 1 HDSEL Half-duplex selection 3 1 HDSEL NotSelected Half duplex mode is not selected 0 Selected Half duplex mode is selected 1 IRLP Ir low-power 2 1 IRLP Normal Normal mode 0 LowPower Low-power mode 1 IREN Ir mode enable 1 1 IREN Disabled IrDA disabled 0 Enabled IrDA enabled 1 EIE Error interrupt enable 0 1 EIE Disabled Interrupt is inhibited 0 Enabled An interrupt is generated when FE=1 or ORE=1 or NF=1 in the ISR register 1 BRR BRR Baud rate register 0xC 0x20 read-write 0x00000000 BRR DIV_Mantissa 0 16 0 65535 GTPR GTPR Guard time and prescaler register 0x10 0x20 read-write 0x00000000 GT Guard time value 8 8 0 255 PSC Prescaler value 0 8 0 255 RTOR RTOR Receiver timeout register 0x14 0x20 read-write 0x00000000 BLEN Block Length 24 8 0 255 RTO Receiver timeout value 0 24 0 16777215 RQR RQR Request register 0x18 0x20 write-only 0x00000000 TXFRQ Transmit data flush request 4 1 TXFRQ Discard Set the TXE flags. This allows to discard the transmit data 1 RXFRQ Receive data flush request 3 1 RXFRQ Discard clears the RXNE flag. This allows to discard the received data without reading it, and avoid an overrun condition 1 MMRQ Mute mode request 2 1 MMRQ Mute Puts the USART in mute mode and sets the RWU flag 1 SBKRQ Send break request 1 1 SBKRQ Break sets the SBKF flag and request to send a BREAK on the line, as soon as the transmit machine is available 1 ABRRQ Auto baud rate request 0 1 ABRRQ Request resets the ABRF flag in the USART_ISR and request an automatic baud rate measurement on the next received data frame 1 ISR ISR Interrupt & status register 0x1C 0x20 read-only 0x000000C0 REACK REACK 22 1 TEACK TEACK 21 1 WUF WUF 20 1 RWU RWU 19 1 RWU Active Receiver in Active mode 0 Mute Receiver in Mute mode 1 SBKF SBKF 18 1 SBKF NoBreak No break character transmitted 0 Break Break character transmitted 1 CMF CMF 17 1 CMF NoMatch No Character match detected 0 Match Character match detected 1 BUSY BUSY 16 1 BUSY Idle USART is idle (no reception) 0 Busy Reception on going 1 ABRF ABRF 15 1 ABRE ABRE 14 1 EOBF EOBF 12 1 EOBF NotReached End of Block not reached 0 Reached End of Block (number of characters) reached 1 RTOF RTOF 11 1 RTOF NotReached Timeout value not reached 0 Reached Timeout value reached without any data reception 1 CTS CTS 10 1 CTS Set CTS line set 0 Reset CTS line reset 1 CTSIF CTSIF 9 1 CTSIF NotChanged No change occurred on the CTS status line 0 Changed A change occurred on the CTS status line 1 LBDF LBDF 8 1 LBDF NotDetected LIN break not detected 0 Detected LIN break detected 1 TXE TXE 7 1 TXE Full Transmit FIFO is full 0 NotFull Transmit FIFO is not full 1 TC TC 6 1 TC TxNotComplete Transmission is not complete 0 TxComplete Transmission is complete 1 RXNE RXNE 5 1 RXNE NoData Data is not received 0 DataReady Received data is ready to be read 1 IDLE IDLE 4 1 IDLE NoIdle No Idle Line is detected 0 Idle Idle Line is detected 1 ORE ORE 3 1 ORE NoOverrun No Overrun error 0 Overrun Overrun error is detected 1 NF NF 2 1 NF NoNoise No noise is detected 0 Noise Noise is detected 1 FE FE 1 1 FE NoError No Framing error is detected 0 Error Framing error or break character is detected 1 PE PE 0 1 PE NoError No parity error 0 Error Parity error 1 ICR ICR Interrupt flag clear register 0x20 0x20 write-only 0x00000000 WUCF Wakeup from Stop mode clear flag 20 1 oneToClear WUCF Clear Clears the WUF flag in the ISR register 1 CMCF Character match clear flag 17 1 oneToClear CMCF Clear Clears the CMF flag in the ISR register 1 EOBCF End of block clear flag 12 1 oneToClear EOBCF Clear Clears the EOBF flag in the ISR register 1 RTOCF Receiver timeout clear flag 11 1 oneToClear RTOCF Clear Clears the RTOF flag in the ISR register 1 CTSCF CTS clear flag 9 1 oneToClear CTSCF Clear Clears the CTSIF flag in the ISR register 1 LBDCF LIN break detection clear flag 8 1 oneToClear LBDCF Clear Clears the LBDF flag in the ISR register 1 TCCF Transmission complete clear flag 6 1 oneToClear TCCF Clear Clears the TC flag in the ISR register 1 IDLECF Idle line detected clear flag 4 1 oneToClear IDLECF Clear Clears the IDLE flag in the ISR register 1 ORECF Overrun error clear flag 3 1 oneToClear ORECF Clear Clears the ORE flag in the ISR register 1 NCF Noise detected clear flag 2 1 oneToClear NCF Clear Clears the NF flag in the ISR register 1 FECF Framing error clear flag 1 1 oneToClear FECF Clear Clears the FE flag in the ISR register 1 PECF Parity error clear flag 0 1 oneToClear PECF Clear Clears the PE flag in the ISR register 1 RDR RDR Receive data register 0x24 0x20 read-only 0x00000000 RDR Receive data value 0 9 0 511 TDR TDR Transmit data register 0x28 0x20 read-write 0x00000000 TDR Transmit data value 0 9 0 511 USART6 0x40011400 USART3 0x40004800 USART3 USART3 global interrupt 39 USART2 0x40004400 USART2 USART2 global interrupt 38 UART5 0x40005000 UART5 UART5 global interrupt 53 UART4 0x40004C00 UART8 0x40007C00 UART8 UART 8 global interrupt 83 UART7 0x40007800 OTG_FS_GLOBAL USB on the go full speed USB_OTG_FS 0x50000000 0x0 0x400 registers GOTGCTL GOTGCTL OTG_FS control and status register (OTG_FS_GOTGCTL) 0x0 0x20 0x00000800 SRQSCS Session request success 0 1 read-only SRQ Session request 1 1 read-write HNGSCS Host negotiation success 8 1 read-only HNPRQ HNP request 9 1 read-write HSHNPEN Host set HNP enable 10 1 read-write DHNPEN Device HNP enabled 11 1 read-write CIDSTS Connector ID status 16 1 read-only DBCT Long/short debounce time 17 1 read-only ASVLD A-session valid 18 1 read-only BSVLD B-session valid 19 1 read-only VBVALOEN VBUS valid override enable 2 1 read-write VBVALOVAL VBUS valid override value 3 1 read-write AVALOEN A-peripheral session valid override enable 4 1 read-write AVALOVAL A-peripheral session valid override value 5 1 read-write BVALOEN B-peripheral session valid override enable 6 1 read-write BVALOVAL B-peripheral session valid override value 7 1 read-write EHEN Embedded host enable 12 1 read-write OTGVER OTG version 20 1 read-write CURMOD Current mode of operation 21 1 read-only GOTGINT GOTGINT OTG_FS interrupt register (OTG_FS_GOTGINT) 0x4 0x20 read-write 0x00000000 SEDET Session end detected 2 1 SRSSCHG Session request success status change 8 1 HNSSCHG Host negotiation success status change 9 1 HNGDET Host negotiation detected 17 1 ADTOCHG A-device timeout change 18 1 DBCDNE Debounce done 19 1 IDCHNG ID input pin changed 20 1 GAHBCFG GAHBCFG OTG_FS AHB configuration register (OTG_FS_GAHBCFG) 0x8 0x20 read-write 0x00000000 GINT Global interrupt mask 0 1 TXFELVL TxFIFO empty level 7 1 PTXFELVL Periodic TxFIFO empty level 8 1 GUSBCFG GUSBCFG OTG_FS USB configuration register (OTG_FS_GUSBCFG) 0xC 0x20 0x00000A00 TOCAL FS timeout calibration 0 3 read-write PHYSEL Full Speed serial transceiver select 6 1 write-only SRPCAP SRP-capable 8 1 read-write HNPCAP HNP-capable 9 1 read-write TRDT USB turnaround time 10 4 read-write FHMOD Force host mode 29 1 read-write FDMOD Force device mode 30 1 read-write GRSTCTL GRSTCTL OTG_FS reset register (OTG_FS_GRSTCTL) 0x10 0x20 0x20000000 CSRST Core soft reset 0 1 read-write HSRST HCLK soft reset 1 1 read-write FCRST Host frame counter reset 2 1 read-write RXFFLSH RxFIFO flush 4 1 read-write TXFFLSH TxFIFO flush 5 1 read-write TXFNUM TxFIFO number 6 5 read-write AHBIDL AHB master idle 31 1 read-only GINTSTS GINTSTS OTG_FS core interrupt register (OTG_FS_GINTSTS) 0x14 0x20 0x04000020 CMOD Current mode of operation 0 1 read-only MMIS Mode mismatch interrupt 1 1 read-write OTGINT OTG interrupt 2 1 read-only SOF Start of frame 3 1 read-write RXFLVL RxFIFO non-empty 4 1 read-only NPTXFE Non-periodic TxFIFO empty 5 1 read-only GINAKEFF Global IN non-periodic NAK effective 6 1 read-only GOUTNAKEFF Global OUT NAK effective 7 1 read-only ESUSP Early suspend 10 1 read-write USBSUSP USB suspend 11 1 read-write USBRST USB reset 12 1 read-write ENUMDNE Enumeration done 13 1 read-write ISOODRP Isochronous OUT packet dropped interrupt 14 1 read-write EOPF End of periodic frame interrupt 15 1 read-write IEPINT IN endpoint interrupt 18 1 read-only OEPINT OUT endpoint interrupt 19 1 read-only IISOIXFR Incomplete isochronous IN transfer 20 1 read-write IPXFR_INCOMPISOOUT Incomplete periodic transfer(Host mode)/Incomplete isochronous OUT transfer(Device mode) 21 1 read-write HPRTINT Host port interrupt 24 1 read-only HCINT Host channels interrupt 25 1 read-only PTXFE Periodic TxFIFO empty 26 1 read-only CIDSCHG Connector ID status change 28 1 read-write DISCINT Disconnect detected interrupt 29 1 read-write SRQINT Session request/new session detected interrupt 30 1 read-write WKUPINT Resume/remote wakeup detected interrupt 31 1 read-write RSTDET Reset detected interrupt 23 1 read-write GINTMSK GINTMSK OTG_FS interrupt mask register (OTG_FS_GINTMSK) 0x18 0x20 0x00000000 MMISM Mode mismatch interrupt mask 1 1 read-write OTGINT OTG interrupt mask 2 1 read-write SOFM Start of frame mask 3 1 read-write RXFLVLM Receive FIFO non-empty mask 4 1 read-write NPTXFEM Non-periodic TxFIFO empty mask 5 1 read-write GINAKEFFM Global non-periodic IN NAK effective mask 6 1 read-write GONAKEFFM Global OUT NAK effective mask 7 1 read-write ESUSPM Early suspend mask 10 1 read-write USBSUSPM USB suspend mask 11 1 read-write USBRST USB reset mask 12 1 read-write ENUMDNEM Enumeration done mask 13 1 read-write ISOODRPM Isochronous OUT packet dropped interrupt mask 14 1 read-write EOPFM End of periodic frame interrupt mask 15 1 read-write IEPINT IN endpoints interrupt mask 18 1 read-write OEPINT OUT endpoints interrupt mask 19 1 read-write IISOIXFRM Incomplete isochronous IN transfer mask 20 1 read-write IPXFRM_IISOOXFRM Incomplete periodic transfer mask(Host mode)/Incomplete isochronous OUT transfer mask(Device mode) 21 1 read-write PRTIM Host port interrupt mask 24 1 read-write HCIM Host channels interrupt mask 25 1 read-write PTXFEM Periodic TxFIFO empty mask 26 1 read-write CIDSCHGM Connector ID status change mask 28 1 read-write DISCINT Disconnect detected interrupt mask 29 1 read-write SRQIM Session request/new session detected interrupt mask 30 1 read-write WUIM Resume/remote wakeup detected interrupt mask 31 1 read-write RSTDETM Reset detected interrupt mask 23 1 read-write LPMIN LPM interrupt mask 27 1 read-write GRXSTSR_Device GRXSTSR_Device OTG_FS Receive status debug read(Device mode) 0x1C 0x20 read-only 0x00000000 EPNUM Endpoint number 0 4 BCNT Byte count 4 11 DPID Data PID 15 2 PKTSTS Packet status 17 4 FRMNUM Frame number 21 4 GRXSTSR_Host GRXSTSR_Host OTG_FS Receive status debug read(Host mode) GRXSTSR_Device 0x1C 0x20 read-only 0x00000000 CHNUM Endpoint number 0 4 BCNT Byte count 4 11 DPID Data PID 15 2 PKTSTS Packet status 17 4 STSPHST Status phase start 27 1 GRXFSIZ GRXFSIZ OTG_FS Receive FIFO size register (OTG_FS_GRXFSIZ) 0x24 0x20 read-write 0x00000200 RXFD RxFIFO depth 0 16 DIEPTXF0 DIEPTXF0_Device OTG_FS Endpoint 0 Transmit FIFO size 0x28 0x20 read-write 0x00000200 TX0FSA Endpoint 0 transmit RAM start address 0 16 TX0FD Endpoint 0 TxFIFO depth 16 16 HNPTXFSIZ_Host HNPTXFSIZ_Host OTG_FS Host non-periodic transmit FIFO size register DIEPTXF0 0x28 0x20 read-write 0x00000200 NPTXFSA Non-periodic transmit RAM start address 0 16 NPTXFD Non-periodic TxFIFO depth 16 16 HNPTXSTS HNPTXSTS OTG_FS non-periodic transmit FIFO/queue status register (OTG_FS_GNPTXSTS) 0x2C 0x20 read-only 0x00080200 NPTXFSAV Non-periodic TxFIFO space available 0 16 NPTQXSAV Non-periodic transmit request queue space available 16 8 NPTXQTOP Top of the non-periodic transmit request queue 24 7 GCCFG GCCFG OTG_FS general core configuration register (OTG_FS_GCCFG) 0x38 0x20 read-write 0x00000000 PWRDWN Power down 16 1 BCDEN Battery charging detector (BCD) enable 17 1 DCDEN Data contact detection (DCD) mode enable 18 1 PDEN Primary detection (PD) mode enable 19 1 SDEN Secondary detection (SD) mode enable 20 1 VBDEN USB VBUS detection enable 21 1 DCDET Data contact detection (DCD) status 0 1 PDET Primary detection (PD) status 1 1 SDET Secondary detection (SD) status 2 1 PS2DET DM pull-up detection status 3 1 CID CID core ID register 0x3C 0x20 read-write 0x00001000 PRODUCT_ID Product ID field 0 32 HPTXFSIZ HPTXFSIZ OTG_FS Host periodic transmit FIFO size register (OTG_FS_HPTXFSIZ) 0x100 0x20 read-write 0x02000600 PTXSA Host periodic TxFIFO start address 0 16 PTXFSIZ Host periodic TxFIFO depth 16 16 5 0x4 1-5 DIEPTXF%s DIEPTXF%s OTG_FS device IN endpoint transmit FIFO size register 0x104 0x20 read-write 0x02000400 INEPTXSA IN endpoint FIFO2 transmit RAM start address 0 16 INEPTXFD IN endpoint TxFIFO depth 16 16 GRXSTSP_Device GRXSTSP_Device OTG status read and pop register (Device mode) 0x20 0x20 read-only 0x02000400 EPNUM Endpoint number 0 4 BCNT Byte count 4 11 DPID Data PID 15 2 PKTSTS Packet status 17 4 FRMNUM Frame number 21 4 GRXSTSP_Host GRXSTSP_Host OTG status read and pop register (Host mode) GRXSTSP_Device 0x20 0x20 read-only 0x02000400 CHNUM Channel number 0 4 BCNT Byte count 4 11 DPID Data PID 15 2 PKTSTS Packet status 17 4 STSPHST Status phase start 27 1 GI2CCTL GI2CCTL OTG I2C access register 0x30 0x20 read-write 0x02000400 RWDATA I2C Read/Write Data 0 8 REGADDR I2C Register Address 8 8 ADDR I2C Address 16 7 I2CEN I2C Enable 23 1 ACK I2C ACK 24 1 I2CDEVADR I2C Device Address 26 2 I2CDATSE0 I2C DatSe0 USB mode 28 1 RW Read/Write Indicator 30 1 BSYDNE I2C Busy/Done 31 1 GPWRDN GPWRDN OTG power down register 0x58 0x20 read-write 0x02000400 ADPMEN ADP module enable 0 1 ADPIF ADP interrupt flag 23 1 GADPCTL GADPCTL OTG ADP timer, control and status register 0x60 0x20 0x02000400 PRBDSCHG Probe discharge 0 2 read-write PRBDELTA Probe delta 2 2 read-write PRBPER Probe period 4 2 read-write RTIM Ramp time 6 11 read-only ENAPRB Enable probe 17 1 read-write ENASNS Enable sense 18 1 read-write ADPRST ADP reset 19 1 read-only ADPEN ADP enable 20 1 read-write ADPPRBIF ADP probe interrupt flag 21 1 read-write ADPSNSIF ADP sense interrupt flag 22 1 read-write ADPTOIF ADP timeout interrupt flag 23 1 read-write ADPPRBIM ADP probe interrupt mask 24 1 read-write ADPSNSIM ADP sense interrupt mask 25 1 read-write ADPTOIM ADP timeout interrupt mask 26 1 read-write AR Access request 27 2 read-write GLPMCFG GLPMCFG OTG core LPM configuration register 0x54 0x20 0x00000000 LPMEN LPM support enable 0 1 read-write LPMACK LPM token acknowledge enable 1 1 read-write BESL Best effort service latency 2 4 read-write REMWAKE bRemoteWake value 6 1 read-write L1SSEN L1 Shallow Sleep enable 7 1 read-write BESLTHRS BESL threshold 8 4 read-write L1DSEN L1 deep sleep enable 12 1 read-write LPMRST LPM response 13 2 read-only SLPSTS Port sleep status 15 1 read-only L1RSMOK Sleep State Resume OK 16 1 read-only LPMCHIDX LPM Channel Index 17 4 read-write LPMRCNT LPM retry count 21 3 read-write SNDLPM Send LPM transaction 24 1 read-write LPMRCNTSTS LPM retry count status 25 3 read-only ENBESL Enable best effort service latency 28 1 read-write OTG_FS_HOST USB on the go full speed USB_OTG_FS 0x50000400 0x0 0x400 registers HCFG HCFG OTG_FS host configuration register (OTG_FS_HCFG) 0x0 0x20 0x00000000 FSLSPCS FS/LS PHY clock select 0 2 read-write FSLSS FS- and LS-only support 2 1 read-write HFIR HFIR OTG_FS Host frame interval register 0x4 0x20 read-write 0x0000EA60 FRIVL Frame interval 0 16 HFNUM HFNUM OTG_FS host frame number/frame time remaining register (OTG_FS_HFNUM) 0x8 0x20 read-only 0x00003FFF FRNUM Frame number 0 16 FTREM Frame time remaining 16 16 HPTXSTS HPTXSTS OTG_FS_Host periodic transmit FIFO/queue status register (OTG_FS_HPTXSTS) 0x10 0x20 0x00080100 PTXFSAVL Periodic transmit data FIFO space available 0 16 read-write PTXQSAV Periodic transmit request queue space available 16 8 read-only PTXQTOP Top of the periodic transmit request queue 24 8 read-only HAINT HAINT OTG_FS Host all channels interrupt register 0x14 0x20 read-only 0x00000000 HAINT Channel interrupts 0 16 HAINTMSK HAINTMSK OTG_FS host all channels interrupt mask register 0x18 0x20 read-write 0x00000000 HAINTM Channel interrupt mask 0 16 HPRT HPRT OTG_FS host port control and status register (OTG_FS_HPRT) 0x40 0x20 0x00000000 PCSTS Port connect status 0 1 read-only PCDET Port connect detected 1 1 read-write PENA Port enable 2 1 read-write PENCHNG Port enable/disable change 3 1 read-write POCA Port overcurrent active 4 1 read-only POCCHNG Port overcurrent change 5 1 read-write PRES Port resume 6 1 read-write PSUSP Port suspend 7 1 read-write PRST Port reset 8 1 read-write PLSTS Port line status 10 2 read-only PPWR Port power 12 1 read-write PTCTL Port test control 13 4 read-write PSPD Port speed 17 2 read-only 12 0x20 0-11 HC%s Host channel 0x100 CHAR HCCHAR0 OTG_FS host channel-0 characteristics register (OTG_FS_HCCHAR0) 0x0 0x20 read-write 0x00000000 MPSIZ Maximum packet size 0 11 EPNUM Endpoint number 11 4 EPDIR Endpoint direction 15 1 LSDEV Low-speed device 17 1 EPTYP Endpoint type 18 2 MCNT Multicount 20 2 DAD Device address 22 7 ODDFRM Odd frame 29 1 CHDIS Channel disable 30 1 CHENA Channel enable 31 1 INT HCINT0 OTG_FS host channel-0 interrupt register (OTG_FS_HCINT0) 0x8 0x20 read-write 0x00000000 XFRC Transfer completed 0 1 CHH Channel halted 1 1 STALL STALL response received interrupt 3 1 NAK NAK response received interrupt 4 1 ACK ACK response received/transmitted interrupt 5 1 TXERR Transaction error 7 1 BBERR Babble error 8 1 FRMOR Frame overrun 9 1 DTERR Data toggle error 10 1 INTMSK HCINTMSK0 OTG_FS host channel-0 mask register (OTG_FS_HCINTMSK0) 0xC 0x20 read-write 0x00000000 XFRCM Transfer completed mask 0 1 CHHM Channel halted mask 1 1 STALLM STALL response received interrupt mask 3 1 NAKM NAK response received interrupt mask 4 1 ACKM ACK response received/transmitted interrupt mask 5 1 NYET response received interrupt mask 6 1 TXERRM Transaction error mask 7 1 BBERRM Babble error mask 8 1 FRMORM Frame overrun mask 9 1 DTERRM Data toggle error mask 10 1 TSIZ HCTSIZ0 OTG_FS host channel-0 transfer size register 0x10 0x20 read-write 0x00000000 XFRSIZ Transfer size 0 19 PKTCNT Packet count 19 10 DPID Data PID 29 2 OTG_FS_DEVICE USB on the go full speed USB_OTG_FS 0x50000800 0x0 0x400 registers DCFG DCFG OTG_FS device configuration register (OTG_FS_DCFG) 0x0 0x20 read-write 0x02200000 DSPD Device speed 0 2 NZLSOHSK Non-zero-length status OUT handshake 2 1 DAD Device address 4 7 PFIVL Periodic frame interval 11 2 DCTL DCTL OTG_FS device control register (OTG_FS_DCTL) 0x4 0x20 0x00000000 RWUSIG Remote wakeup signaling 0 1 read-write SDIS Soft disconnect 1 1 read-write GINSTS Global IN NAK status 2 1 read-only GONSTS Global OUT NAK status 3 1 read-only TCTL Test control 4 3 read-write SGINAK Set global IN NAK 7 1 read-write CGINAK Clear global IN NAK 8 1 read-write SGONAK Set global OUT NAK 9 1 read-write CGONAK Clear global OUT NAK 10 1 read-write POPRGDNE Power-on programming done 11 1 read-write DSTS DSTS OTG_FS device status register (OTG_FS_DSTS) 0x8 0x20 read-only 0x00000010 SUSPSTS Suspend status 0 1 ENUMSPD Enumerated speed 1 2 EERR Erratic error 3 1 FNSOF Frame number of the received SOF 8 14 DIEPMSK DIEPMSK OTG_FS device IN endpoint common interrupt mask register (OTG_FS_DIEPMSK) 0x10 0x20 read-write 0x00000000 XFRCM Transfer completed interrupt mask 0 1 EPDM Endpoint disabled interrupt mask 1 1 TOM Timeout condition mask (Non-isochronous endpoints) 3 1 ITTXFEMSK IN token received when TxFIFO empty mask 4 1 INEPNMM IN token received with EP mismatch mask 5 1 INEPNEM IN endpoint NAK effective mask 6 1 DOEPMSK DOEPMSK OTG_FS device OUT endpoint common interrupt mask register (OTG_FS_DOEPMSK) 0x14 0x20 read-write 0x00000000 XFRCM Transfer completed interrupt mask 0 1 EPDM Endpoint disabled interrupt mask 1 1 STUPM SETUP phase done mask 3 1 OTEPDM OUT token received when endpoint disabled mask 4 1 DAINT DAINT OTG_FS device all endpoints interrupt register (OTG_FS_DAINT) 0x18 0x20 read-only 0x00000000 IEPINT IN endpoint interrupt bits 0 16 OEPINT OUT endpoint interrupt bits 16 16 DAINTMSK DAINTMSK OTG_FS all endpoints interrupt mask register (OTG_FS_DAINTMSK) 0x1C 0x20 read-write 0x00000000 IEPM IN EP interrupt mask bits 0 16 OEPM OUT EP interrupt mask bits 16 16 DVBUSDIS DVBUSDIS OTG_FS device VBUS discharge time register 0x28 0x20 read-write 0x000017D7 VBUSDT Device VBUS discharge time 0 16 DVBUSPULSE DVBUSPULSE OTG_FS device VBUS pulsing time register 0x2C 0x20 read-write 0x000005B8 DVBUSP Device VBUS pulsing time 0 12 DIEPEMPMSK DIEPEMPMSK OTG_FS device IN endpoint FIFO empty interrupt mask register 0x34 0x20 read-write 0x00000000 INEPTXFEM IN EP Tx FIFO empty interrupt mask bits 0 16 DIEP0 Device IN endpoint 0 0x100 CTL DIEPCTL0 OTG_FS device control IN endpoint 0 control register (OTG_FS_DIEPCTL0) 0x0 0x20 0x00000000 MPSIZ Maximum packet size 0 2 read-write USBAEP USB active endpoint 15 1 read-only NAKSTS NAK status 17 1 read-only EPTYP Endpoint type 18 2 read-only STALL STALL handshake 21 1 read-write TXFNUM TxFIFO number 22 4 read-write CNAK Clear NAK 26 1 write-only SNAK Set NAK 27 1 write-only EPDIS Endpoint disable 30 1 read-only EPENA Endpoint enable 31 1 read-write INT DIEPINT0 device endpoint-x interrupt register 0x8 0x20 0x00000080 TXFE TXFE 7 1 read-only INEPNE INEPNE 6 1 read-write ITTXFE ITTXFE 4 1 read-write TOC TOC 3 1 read-write EPDISD EPDISD 1 1 read-write XFRC XFRC 0 1 read-write TSIZ DIEPTSIZ0 device endpoint-0 transfer size register 0x10 0x20 read-write 0x00000000 PKTCNT Packet count 19 2 XFRSIZ Transfer size 0 7 TXFSTS DTXFSTS0 OTG_FS device IN endpoint transmit FIFO status register 0x18 0x20 read-only 0x00000000 INEPTFSAV IN endpoint TxFIFO space available 0 16 5 0x20 1-5 DIEP%s Device IN endpoint X 0x120 CTL DIEPCTL1 OTG device endpoint-1 control register 0x0 0x20 0x00000000 EPENA EPENA 31 1 read-write EPDIS EPDIS 30 1 read-write SODDFRM_SD1PID SODDFRM/SD1PID 29 1 write-only SD0PID_SEVNFRM SD0PID/SEVNFRM 28 1 write-only SNAK SNAK 27 1 write-only CNAK CNAK 26 1 write-only TXFNUM TXFNUM 22 4 read-write STALL STALL handshake 21 1 read-write EPTYP EPTYP 18 2 read-write NAKSTS NAKSTS 17 1 read-only EONUM_DPID EONUM/DPID 16 1 read-only USBAEP USBAEP 15 1 read-write MPSIZ MPSIZ 0 11 read-write INT DIEPINT1 device endpoint-1 interrupt register 0x8 TSIZ DIEPTSIZ1 device endpoint-1 transfer size register 0x10 0x20 read-write 0x00000000 MCNT Multi count 29 2 PKTCNT Packet count 19 10 XFRSIZ Transfer size 0 19 TXFSTS DTXFSTS1 OTG_FS device IN endpoint transmit FIFO status register 0x18 DOEP0 Device OUT endpoint 0 0x300 CTL DOEPCTL0 device endpoint-0 control register 0x0 0x20 0x00008000 EPENA EPENA 31 1 read-write EPDIS EPDIS 30 1 read-only SNAK SNAK 27 1 write-only CNAK CNAK 26 1 write-only STALL STALL handshake 21 1 read-write SNPM SNPM 20 1 read-write EPTYP EPTYP 18 2 read-only NAKSTS NAKSTS 17 1 read-only USBAEP USBAEP 15 1 read-only MPSIZ MPSIZ 0 2 read-only INT DOEPINT0 device endpoint-0 interrupt register 0x8 0x20 read-write 0x00000080 B2BSTUP B2BSTUP 6 1 OTEPDIS OTEPDIS 4 1 STUP STUP 3 1 EPDISD EPDISD 1 1 XFRC XFRC 0 1 TSIZ DOEPTSIZ0 device OUT endpoint-0 transfer size register 0x10 0x20 read-write 0x00000000 STUPCNT SETUP packet count 29 2 PKTCNT Packet count 19 1 XFRSIZ Transfer size 0 7 5 0x20 1-5 DOEP%s Device IN endpoint X 0x320 CTL DOEPCTL1 device endpoint-1 control register 0x0 0x20 0x00000000 EPENA EPENA 31 1 read-write EPDIS EPDIS 30 1 read-write SODDFRM SODDFRM 29 1 write-only SD0PID_SEVNFRM SD0PID/SEVNFRM 28 1 write-only SNAK SNAK 27 1 write-only CNAK CNAK 26 1 write-only STALL STALL handshake 21 1 read-write SNPM SNPM 20 1 read-write EPTYP EPTYP 18 2 read-write NAKSTS NAKSTS 17 1 read-only EONUM_DPID EONUM/DPID 16 1 read-only USBAEP USBAEP 15 1 read-write MPSIZ MPSIZ 0 11 read-write INT DOEPINT1 device endpoint-1 interrupt register 0x8 TSIZ DOEPTSIZ1 device OUT endpoint-1 transfer size register 0x10 0x20 read-write 0x00000000 RXDPID_STUPCNT Received data PID/SETUP packet count 29 2 PKTCNT Packet count 19 10 XFRSIZ Transfer size 0 19 OTG_FS_PWRCLK USB on the go full speed USB_OTG_FS 0x50000E00 0x0 0x400 registers OTG_FS_WKUP USB On-The-Go FS Wakeup through EXTI line interrupt 42 OTG_FS USB On The Go FS global interrupt 67 PCGCCTL PCGCCTL OTG_FS power and clock gating control register (OTG_FS_PCGCCTL) 0x0 0x20 read-write 0x00000000 STPPCLK Stop PHY clock 0 1 GATEHCLK Gate HCLK 1 1 PHYSUSP PHY Suspended 4 1 OTG_HS_GLOBAL USB on the go high speed USB_OTG_HS 0x40040000 0x0 0x400 registers GOTGCTL GOTGCTL OTG_HS control and status register 0x0 0x20 0x00000800 SRQSCS Session request success 0 1 read-only SRQ Session request 1 1 read-write HNGSCS Host negotiation success 8 1 read-only HNPRQ HNP request 9 1 read-write HSHNPEN Host set HNP enable 10 1 read-write DHNPEN Device HNP enabled 11 1 read-write CIDSTS Connector ID status 16 1 read-only DBCT Long/short debounce time 17 1 read-only ASVLD A-session valid 18 1 read-only BSVLD B-session valid 19 1 read-only EHEN Embedded host enable 12 1 read-write VBVALOEN V_BUS valid override enable 2 1 read-write VBVALOVAL V_BUS valid override value 3 1 read-write AVALOEN A-peripheral session valid override enable 4 1 read-write AVALOVAL A-peripheral session valid override value 5 1 read-write BVALOEN B-peripheral session valid override enable 6 1 read-write BVALOVAL B-peripheral session valid override value 7 1 read-write OTGVER OTG version 20 1 read-write CURMOD Current mode of operation 21 1 read-only GOTGINT GOTGINT OTG_HS interrupt register 0x4 0x20 read-write 0x00000000 SEDET Session end detected 2 1 SRSSCHG Session request success status change 8 1 HNSSCHG Host negotiation success status change 9 1 HNGDET Host negotiation detected 17 1 ADTOCHG A-device timeout change 18 1 DBCDNE Debounce done 19 1 IDCHNG ID input pin changed 20 1 GAHBCFG GAHBCFG OTG_HS AHB configuration register 0x8 0x20 read-write 0x00000000 GINT Global interrupt mask 0 1 HBSTLEN Burst length/type 1 4 DMAEN DMA enable 5 1 TXFELVL TxFIFO empty level 7 1 PTXFELVL Periodic TxFIFO empty level 8 1 GUSBCFG GUSBCFG OTG_HS USB configuration register 0xC 0x20 0x00000A00 TOCAL FS timeout calibration 0 3 read-write PHYSEL USB 2.0 high-speed ULPI PHY or USB 1.1 full-speed serial transceiver select 6 1 write-only SRPCAP SRP-capable 8 1 read-write HNPCAP HNP-capable 9 1 read-write TRDT USB turnaround time 10 4 read-write PHYLPCS PHY Low-power clock select 15 1 read-write ULPIFSLS ULPI FS/LS select 17 1 read-write ULPIAR ULPI Auto-resume 18 1 read-write ULPICSM ULPI Clock SuspendM 19 1 read-write ULPIEVBUSD ULPI External VBUS Drive 20 1 read-write ULPIEVBUSI ULPI external VBUS indicator 21 1 read-write TSDPS TermSel DLine pulsing selection 22 1 read-write PCCI Indicator complement 23 1 read-write PTCI Indicator pass through 24 1 read-write ULPIIPD ULPI interface protect disable 25 1 read-write FHMOD Forced host mode 29 1 read-write FDMOD Forced peripheral mode 30 1 read-write GRSTCTL GRSTCTL OTG_HS reset register 0x10 0x20 0x20000000 CSRST Core soft reset 0 1 read-write HSRST HCLK soft reset 1 1 read-write FCRST Host frame counter reset 2 1 read-write RXFFLSH RxFIFO flush 4 1 read-write TXFFLSH TxFIFO flush 5 1 read-write TXFNUM TxFIFO number 6 5 read-write AHBIDL AHB master idle 31 1 read-only DMAREQ DMA request signal enabled for USB OTG HS 30 1 read-only GINTSTS GINTSTS OTG_HS core interrupt register 0x14 0x20 0x04000020 CMOD Current mode of operation 0 1 read-only MMIS Mode mismatch interrupt 1 1 read-write OTGINT OTG interrupt 2 1 read-only SOF Start of frame 3 1 read-write RXFLVL RxFIFO nonempty 4 1 read-only NPTXFE Nonperiodic TxFIFO empty 5 1 read-only GINAKEFF Global IN nonperiodic NAK effective 6 1 read-only BOUTNAKEFF Global OUT NAK effective 7 1 read-only ESUSP Early suspend 10 1 read-write USBSUSP USB suspend 11 1 read-write USBRST USB reset 12 1 read-write ENUMDNE Enumeration done 13 1 read-write ISOODRP Isochronous OUT packet dropped interrupt 14 1 read-write EOPF End of periodic frame interrupt 15 1 read-write IEPINT IN endpoint interrupt 18 1 read-only OEPINT OUT endpoint interrupt 19 1 read-only IISOIXFR Incomplete isochronous IN transfer 20 1 read-write PXFR_INCOMPISOOUT Incomplete periodic transfer 21 1 read-write DATAFSUSP Data fetch suspended 22 1 read-write HPRTINT Host port interrupt 24 1 read-only HCINT Host channels interrupt 25 1 read-only PTXFE Periodic TxFIFO empty 26 1 read-only CIDSCHG Connector ID status change 28 1 read-write DISCINT Disconnect detected interrupt 29 1 read-write SRQINT Session request/new session detected interrupt 30 1 read-write WKUINT Resume/remote wakeup detected interrupt 31 1 read-write GINTMSK GINTMSK OTG_HS interrupt mask register 0x18 0x20 0x00000000 MMISM Mode mismatch interrupt mask 1 1 read-write OTGINT OTG interrupt mask 2 1 read-write SOFM Start of frame mask 3 1 read-write RXFLVLM Receive FIFO nonempty mask 4 1 read-write NPTXFEM Nonperiodic TxFIFO empty mask 5 1 read-write GINAKEFFM Global nonperiodic IN NAK effective mask 6 1 read-write GONAKEFFM Global OUT NAK effective mask 7 1 read-write ESUSPM Early suspend mask 10 1 read-write USBSUSPM USB suspend mask 11 1 read-write USBRST USB reset mask 12 1 read-write ENUMDNEM Enumeration done mask 13 1 read-write ISOODRPM Isochronous OUT packet dropped interrupt mask 14 1 read-write EOPFM End of periodic frame interrupt mask 15 1 read-write IEPINT IN endpoints interrupt mask 18 1 read-write OEPINT OUT endpoints interrupt mask 19 1 read-write IISOIXFRM Incomplete isochronous IN transfer mask 20 1 read-write PXFRM_IISOOXFRM Incomplete periodic transfer mask 21 1 read-write FSUSPM Data fetch suspended mask 22 1 read-write PRTIM Host port interrupt mask 24 1 read-only HCIM Host channels interrupt mask 25 1 read-write PTXFEM Periodic TxFIFO empty mask 26 1 read-write CIDSCHGM Connector ID status change mask 28 1 read-write DISCINT Disconnect detected interrupt mask 29 1 read-write SRQIM Session request/new session detected interrupt mask 30 1 read-write WUIM Resume/remote wakeup detected interrupt mask 31 1 read-write RSTDE Reset detected interrupt mask 23 1 read-write LPMINTM LPM interrupt mask 27 1 read-write GRXSTSR_Host GRXSTSR_Host OTG_HS Receive status debug read register (host mode) 0x1C 0x20 read-only 0x00000000 CHNUM Channel number 0 4 BCNT Byte count 4 11 DPID Data PID 15 2 PKTSTS Packet status 17 4 GRXSTSP_Host GRXSTSP_Host OTG_HS status read and pop register (host mode) 0x20 0x20 read-only 0x00000000 CHNUM Channel number 0 4 BCNT Byte count 4 11 DPID Data PID 15 2 PKTSTS Packet status 17 4 GRXFSIZ GRXFSIZ OTG_HS Receive FIFO size register 0x24 0x20 read-write 0x00000200 RXFD RxFIFO depth 0 16 HNPTXFSIZ HNPTXFSIZ_Host OTG_HS nonperiodic transmit FIFO size register (host mode) 0x28 0x20 read-write 0x00000200 NPTXFSA Nonperiodic transmit RAM start address 0 16 NPTXFD Nonperiodic TxFIFO depth 16 16 DIEPTXF0 DIEPTXF0_Device Endpoint 0 transmit FIFO size (peripheral mode) HNPTXFSIZ 0x28 0x20 read-write 0x00000200 TX0FSA Endpoint 0 transmit RAM start address 0 16 TX0FD Endpoint 0 TxFIFO depth 16 16 HNPTXSTS GNPTXSTS OTG_HS nonperiodic transmit FIFO/queue status register 0x2C 0x20 read-only 0x00080200 NPTXFSAV Nonperiodic TxFIFO space available 0 16 NPTQXSAV Nonperiodic transmit request queue space available 16 8 NPTXQTOP Top of the nonperiodic transmit request queue 24 7 GCCFG GCCFG OTG_HS general core configuration register 0x38 0x20 read-write 0x00000000 PWRDWN Power down 16 1 BCDEN Battery charging detector (BCD) enable 17 1 DCDEN Data contact detection (DCD) mode enable 18 1 PDEN Primary detection (PD) mode enable 19 1 SDEN Secondary detection (SD) mode enable 20 1 VBDEN USB VBUS detection enable 21 1 DCDET Data contact detection (DCD) status 0 1 PDET Primary detection (PD) status 1 1 SDET Secondary detection (SD) status 2 1 PS2DET DM pull-up detection status 3 1 CID CID OTG_HS core ID register 0x3C 0x20 read-write 0x00001200 PRODUCT_ID Product ID field 0 32 HPTXFSIZ HPTXFSIZ OTG_HS Host periodic transmit FIFO size register 0x100 0x20 read-write 0x02000600 PTXSA Host periodic TxFIFO start address 0 16 PTXFD Host periodic TxFIFO depth 16 16 8 0x4 1-8 DIEPTXF%s DIEPTXF%s OTG_HS device IN endpoint transmit FIFO size register 0x104 0x20 read-write 0x02000400 INEPTXSA IN endpoint FIFOx transmit RAM start address 0 16 INEPTXFD IN endpoint TxFIFO depth 16 16 GRXSTSR_Device GRXSTSR_Device OTG_HS Receive status debug read register (peripheral mode mode) GRXSTSR_Host 0x1C 0x20 read-only 0x00000000 EPNUM Endpoint number 0 4 BCNT Byte count 4 11 DPID Data PID 15 2 PKTSTS Packet status 17 4 FRMNUM Frame number 21 4 GRXSTSP_Device GRXSTSP_Device OTG_HS status read and pop register (peripheral mode) GRXSTSP_Host 0x20 0x20 read-only 0x00000000 EPNUM Endpoint number 0 4 BCNT Byte count 4 11 DPID Data PID 15 2 PKTSTS Packet status 17 4 FRMNUM Frame number 21 4 GLPMCFG GLPMCFG OTG core LPM configuration register 0x54 0x20 0x00000000 LPMEN LPM support enable 0 1 read-write LPMACK LPM token acknowledge enable 1 1 read-write BESL Best effort service latency 2 4 read-only REMWAKE bRemoteWake value 6 1 read-only L1SSEN L1 Shallow Sleep enable 7 1 read-write BESLTHRS BESL threshold 8 4 read-write L1DSEN L1 deep sleep enable 12 1 read-write LPMRST LPM response 13 2 read-only SLPSTS Port sleep status 15 1 read-only L1RSMOK Sleep State Resume OK 16 1 read-only LPMCHIDX LPM Channel Index 17 4 read-write LPMRCNT LPM retry count 21 3 read-write SNDLPM Send LPM transaction 24 1 read-write LPMRCNTSTS LPM retry count status 25 3 read-only ENBESL Enable best effort service latency 28 1 read-write OTG_HS_HOST USB on the go high speed USB_OTG_HS 0x40040400 0x0 0x400 registers HCFG HCFG OTG_HS host configuration register 0x0 0x20 0x00000000 FSLSPCS FS/LS PHY clock select 0 2 read-write FSLSS FS- and LS-only support 2 1 read-only HFIR HFIR OTG_HS Host frame interval register 0x4 0x20 read-write 0x0000EA60 FRIVL Frame interval 0 16 HFNUM HFNUM OTG_HS host frame number/frame time remaining register 0x8 0x20 read-only 0x00003FFF FRNUM Frame number 0 16 FTREM Frame time remaining 16 16 HPTXSTS HPTXSTS OTG_HS_Host periodic transmit FIFO/queue status register 0x10 0x20 0x00080100 PTXFSAVL Periodic transmit data FIFO space available 0 16 read-write PTXQSAV Periodic transmit request queue space available 16 8 read-only PTXQTOP Top of the periodic transmit request queue 24 8 read-only HAINT HAINT OTG_HS Host all channels interrupt register 0x14 0x20 read-only 0x00000000 HAINT Channel interrupts 0 16 HAINTMSK HAINTMSK OTG_HS host all channels interrupt mask register 0x18 0x20 read-write 0x00000000 HAINTM Channel interrupt mask 0 16 HPRT HPRT OTG_HS host port control and status register 0x40 0x20 0x00000000 PCSTS Port connect status 0 1 read-only PCDET Port connect detected 1 1 read-write PENA Port enable 2 1 read-write PENCHNG Port enable/disable change 3 1 read-write POCA Port overcurrent active 4 1 read-only POCCHNG Port overcurrent change 5 1 read-write PRES Port resume 6 1 read-write PSUSP Port suspend 7 1 read-write PRST Port reset 8 1 read-write PLSTS Port line status 10 2 read-only PPWR Port power 12 1 read-write PTCTL Port test control 13 4 read-write PSPD Port speed 17 2 read-only 16 0x20 0-15 HC%s Host channel 0x100 CHAR HCCHAR0 OTG_HS host channel-0 characteristics register 0x0 0x20 read-write 0x00000000 MPSIZ Maximum packet size 0 11 EPNUM Endpoint number 11 4 EPDIR Endpoint direction 15 1 LSDEV Low-speed device 17 1 EPTYP Endpoint type 18 2 MC Multi Count (MC) / Error Count (EC) 20 2 DAD Device address 22 7 ODDFRM Odd frame 29 1 CHDIS Channel disable 30 1 CHENA Channel enable 31 1 SPLT HCSPLT0 OTG_HS host channel-0 split control register 0x4 0x20 read-write 0x00000000 PRTADDR Port address 0 7 HUBADDR Hub address 7 7 XACTPOS XACTPOS 14 2 COMPLSPLT Do complete split 16 1 SPLITEN Split enable 31 1 INT HCINT0 OTG_HS host channel-11 interrupt register 0x8 0x20 read-write 0x00000000 XFRC Transfer completed 0 1 CHH Channel halted 1 1 AHBERR AHB error 2 1 STALL STALL response received interrupt 3 1 NAK NAK response received interrupt 4 1 ACK ACK response received/transmitted interrupt 5 1 NYET Response received interrupt 6 1 TXERR Transaction error 7 1 BBERR Babble error 8 1 FRMOR Frame overrun 9 1 DTERR Data toggle error 10 1 INTMSK HCINTMSK0 OTG_HS host channel-11 interrupt mask register 0xC 0x20 read-write 0x00000000 XFRCM Transfer completed mask 0 1 CHHM Channel halted mask 1 1 AHBERR AHB error 2 1 STALLM STALL response received interrupt mask 3 1 NAKM NAK response received interrupt mask 4 1 ACKM ACK response received/transmitted interrupt mask 5 1 NYET response received interrupt mask 6 1 TXERRM Transaction error mask 7 1 BBERRM Babble error mask 8 1 FRMORM Frame overrun mask 9 1 DTERRM Data toggle error mask 10 1 TSIZ HCTSIZ0 OTG_HS host channel-11 transfer size register 0x10 0x20 read-write 0x00000000 XFRSIZ Transfer size 0 19 PKTCNT Packet count 19 10 DPID Data PID 29 2 DMA HCDMA0 OTG_HS host channel-0 DMA address register 0x14 0x20 read-write 0x00000000 DMAADDR DMA address 0 32 OTG_HS_DEVICE USB on the go high speed USB_OTG_HS 0x40040800 0x0 0x400 registers DCFG DCFG OTG_HS device configuration register 0x0 0x20 read-write 0x02200000 DSPD Device speed 0 2 NZLSOHSK Nonzero-length status OUT handshake 2 1 DAD Device address 4 7 PFIVL Periodic (micro)frame interval 11 2 PERSCHIVL Periodic scheduling interval 24 2 DCTL DCTL OTG_HS device control register 0x4 0x20 0x00000000 RWUSIG Remote wakeup signaling 0 1 read-write SDIS Soft disconnect 1 1 read-write GINSTS Global IN NAK status 2 1 read-only GONSTS Global OUT NAK status 3 1 read-only TCTL Test control 4 3 read-write SGINAK Set global IN NAK 7 1 write-only CGINAK Clear global IN NAK 8 1 write-only SGONAK Set global OUT NAK 9 1 write-only CGONAK Clear global OUT NAK 10 1 write-only POPRGDNE Power-on programming done 11 1 read-write DSTS DSTS OTG_HS device status register 0x8 0x20 read-only 0x00000010 SUSPSTS Suspend status 0 1 ENUMSPD Enumerated speed 1 2 EERR Erratic error 3 1 FNSOF Frame number of the received SOF 8 14 DIEPMSK DIEPMSK OTG_HS device IN endpoint common interrupt mask register 0x10 0x20 read-write 0x00000000 XFRCM Transfer completed interrupt mask 0 1 EPDM Endpoint disabled interrupt mask 1 1 TOM Timeout condition mask (nonisochronous endpoints) 3 1 ITTXFEMSK IN token received when TxFIFO empty mask 4 1 INEPNMM IN token received with EP mismatch mask 5 1 INEPNEM IN endpoint NAK effective mask 6 1 TXFURM FIFO underrun mask 8 1 BIM BNA interrupt mask 9 1 DOEPMSK DOEPMSK OTG_HS device OUT endpoint common interrupt mask register 0x14 0x20 read-write 0x00000000 XFRCM Transfer completed interrupt mask 0 1 EPDM Endpoint disabled interrupt mask 1 1 STUPM SETUP phase done mask 3 1 OTEPDM OUT token received when endpoint disabled mask 4 1 B2BSTUP Back-to-back SETUP packets received mask 6 1 OPEM OUT packet error mask 8 1 BOIM BNA interrupt mask 9 1 DAINT DAINT OTG_HS device all endpoints interrupt register 0x18 0x20 read-only 0x00000000 IEPINT IN endpoint interrupt bits 0 16 OEPINT OUT endpoint interrupt bits 16 16 DAINTMSK DAINTMSK OTG_HS all endpoints interrupt mask register 0x1C 0x20 read-write 0x00000000 IEPM IN EP interrupt mask bits 0 16 OEPM OUT EP interrupt mask bits 16 16 DVBUSDIS DVBUSDIS OTG_HS device VBUS discharge time register 0x28 0x20 read-write 0x000017D7 VBUSDT Device VBUS discharge time 0 16 DVBUSPULSE DVBUSPULSE OTG_HS device VBUS pulsing time register 0x2C 0x20 read-write 0x000005B8 DVBUSP Device VBUS pulsing time 0 12 DTHRCTL DTHRCTL OTG_HS Device threshold control register 0x30 0x20 read-write 0x00000000 NONISOTHREN Nonisochronous IN endpoints threshold enable 0 1 ISOTHREN ISO IN endpoint threshold enable 1 1 TXTHRLEN Transmit threshold length 2 9 RXTHREN Receive threshold enable 16 1 RXTHRLEN Receive threshold length 17 9 ARPEN Arbiter parking enable 27 1 DIEPEMPMSK DIEPEMPMSK OTG_HS device IN endpoint FIFO empty interrupt mask register 0x34 0x20 read-write 0x00000000 INEPTXFEM IN EP Tx FIFO empty interrupt mask bits 0 16 DEACHINT DEACHINT OTG_HS device each endpoint interrupt register 0x38 0x20 read-write 0x00000000 IEP1INT IN endpoint 1interrupt bit 1 1 OEP1INT OUT endpoint 1 interrupt bit 17 1 DEACHINTMSK DEACHINTMSK OTG_HS device each endpoint interrupt register mask 0x3C 0x20 read-write 0x00000000 IEP1INTM IN Endpoint 1 interrupt mask bit 1 1 OEP1INTM OUT Endpoint 1 interrupt mask bit 17 1 DIEPEACHMSK1 0x44 0x20 read-write 0x00000000 XFRCM Transfer completed interrupt mask 0 1 EPDM Endpoint disabled interrupt mask 1 1 AHBERRM AHB error mask 2 1 TOM Timeout condition mask (Non-isochronous endpoints) 3 1 ITTXFEMSK IN token received when TxFIFO empty mask 4 1 INEPNEM IN endpoint NAK effective mask 6 1 TXFURM FIFO underrun mask 8 1 BNAM BNA interrupt mask 9 1 NAKM NAK interrupt mask 13 1 DOEPEACHMSK1 0x84 0x20 read-write 0x00000000 XFRCM Transfer completed interrupt mask 0 1 EPDM Endpoint disabled interrupt mask 1 1 AHBERRM AHB error mask 2 1 STUPM SETUP phase done mask 3 1 OTEPDM OUT token received when endpoint disabled mask 4 1 B2BSTUPM Back-to-back SETUP packets received mask 6 1 OUTPKTERRM Out packet error mask 8 1 BNAM BNA interrupt mask 9 1 BERRM Babble error interrupt mask 12 1 NAKMSK NAK interrupt mask 13 1 NYETMSK NYET interrupt mask 14 1 DIEP0 Device IN endpoint 0 0x100 CTL DIEPCTL0 OTG device endpoint-0 control register 0x0 0x20 0x00000000 MPSIZ Maximum packet size 0 11 read-write USBAEP USB active endpoint 15 1 read-write EONUM_DPID Even/odd frame 16 1 read-only NAKSTS NAK status 17 1 read-only EPTYP Endpoint type 18 2 read-write STALL STALL handshake 21 1 read-write TXFNUM TxFIFO number 22 4 read-write CNAK Clear NAK 26 1 write-only SNAK Set NAK 27 1 write-only SD0PID_SEVNFRM Set DATA0 PID 28 1 write-only SODDFRM Set odd frame 29 1 write-only EPDIS Endpoint disable 30 1 read-write EPENA Endpoint enable 31 1 read-write INT DIEPINT0 OTG device endpoint-0 interrupt register 0x8 0x20 0x00000080 XFRC Transfer completed interrupt 0 1 read-write EPDISD Endpoint disabled interrupt 1 1 read-write TOC Timeout condition 3 1 read-write ITTXFE IN token received when TxFIFO is empty 4 1 read-write INEPNE IN endpoint NAK effective 6 1 read-write TXFE Transmit FIFO empty 7 1 read-only TXFIFOUDRN Transmit Fifo Underrun 8 1 read-write BNA Buffer not available interrupt 9 1 read-write PKTDRPSTS Packet dropped status 11 1 read-write BERR Babble error interrupt 12 1 read-write NAK NAK interrupt 13 1 read-write TSIZ DIEPTSIZ0 OTG_HS device IN endpoint 0 transfer size register 0x10 0x20 read-write 0x00000000 XFRSIZ Transfer size 0 7 PKTCNT Packet count 19 2 DMA OTG_HS device endpoint-0 DMA address register 0x14 0x20 read-write 0x00000000 DMAADDR DMA address 0 32 TXFSTS DTXFSTS0 OTG_HS device IN endpoint transmit FIFO status register 0x18 0x20 read-only 0x00000000 INEPTFSAV IN endpoint TxFIFO space avail 0 16 8 0x20 1-8 DIEP%s Device IN endpoint X 0x120 CTL DIEPCTL1 OTG device endpoint-1 control register 0x0 0x20 0x00000000 MPSIZ Maximum packet size 0 11 read-write USBAEP USB active endpoint 15 1 read-write EONUM_DPID Even/odd frame 16 1 read-only NAKSTS NAK status 17 1 read-only EPTYP Endpoint type 18 2 read-write STALL STALL handshake 21 1 read-write TXFNUM TxFIFO number 22 4 read-write CNAK Clear NAK 26 1 write-only SNAK Set NAK 27 1 write-only SD0PID_SEVNFRM Set DATA0 PID 28 1 write-only SODDFRM Set odd frame 29 1 write-only EPDIS Endpoint disable 30 1 read-write EPENA Endpoint enable 31 1 read-write INT DIEPINT1 OTG device endpoint-1 interrupt register 0x8 TSIZ DIEPTSIZ1 OTG_HS device endpoint transfer size register 0x10 0x20 read-write 0x00000000 XFRSIZ Transfer size 0 19 PKTCNT Packet count 19 10 MCNT Multi count 29 2 DMA DIEPDMA1 OTG_HS device endpoint-1 DMA address register 0x14 TXFSTS DTXFSTS1 OTG_HS device IN endpoint transmit FIFO status register 0x18 DOEP0 Device OUT endpoint 0 0x300 CTL DOEPCTL0 OTG_HS device control OUT endpoint 0 control register 0x0 0x20 0x00008000 MPSIZ Maximum packet size 0 2 read-only USBAEP USB active endpoint 15 1 read-only NAKSTS NAK status 17 1 read-only EPTYP Endpoint type 18 2 read-only SNPM Snoop mode 20 1 read-write STALL STALL handshake 21 1 read-write CNAK Clear NAK 26 1 write-only SNAK Set NAK 27 1 write-only EPDIS Endpoint disable 30 1 read-only EPENA Endpoint enable 31 1 read-write INT DOEPINT0 OTG_HS device endpoint-0 interrupt register 0x8 0x20 read-write 0x00000080 XFRC Transfer completed interrupt 0 1 EPDISD Endpoint disabled interrupt 1 1 STUP SETUP phase done 3 1 OTEPDIS OUT token received when endpoint disabled 4 1 B2BSTUP Back-to-back SETUP packets received 6 1 NYET NYET interrupt 14 1 TSIZ DOEPTSIZ0 OTG_HS device endpoint-0 transfer size register 0x10 0x20 read-write 0x00000000 XFRSIZ Transfer size 0 7 PKTCNT Packet count 19 1 STUPCNT SETUP packet count 29 2 DMA OTG_HS device endpoint-0 DMA address register 0x14 0x20 read-write 0x00000000 DMAADDR DMA address 0 32 8 0x20 1-8 DOEP%s Device IN endpoint X 0x320 CTL DOEPCTL1 OTG device endpoint-1 control register 0x0 0x20 0x00000000 MPSIZ Maximum packet size 0 11 read-write USBAEP USB active endpoint 15 1 read-write EONUM_DPID Even odd frame/Endpoint data PID 16 1 read-only NAKSTS NAK status 17 1 read-only EPTYP Endpoint type 18 2 read-write SNPM Snoop mode 20 1 read-write STALL STALL handshake 21 1 read-write CNAK Clear NAK 26 1 write-only SNAK Set NAK 27 1 write-only SD0PID_SEVNFRM Set DATA0 PID/Set even frame 28 1 write-only SODDFRM Set odd frame 29 1 write-only EPDIS Endpoint disable 30 1 read-write EPENA Endpoint enable 31 1 read-write INT DOEPINT1 OTG_HS device endpoint-1 interrupt register 0x8 DMA OTG_HS device endpoint-1 DMA address register 0x14 TSIZ DOEPTSIZ1 OTG_HS device endpoint-1 transfer size register 0x10 0x20 read-write 0x00000000 XFRSIZ Transfer size 0 19 PKTCNT Packet count 19 10 RXDPID_STUPCNT Received data PID/SETUP packet count 29 2 OTG_HS_PWRCLK USB on the go high speed USB_OTG_HS 0x40040E00 0x0 0x3F200 registers OTG_HS_EP1_OUT USB On The Go HS End Point 1 Out global interrupt 74 OTG_HS_EP1_IN USB On The Go HS End Point 1 In global interrupt 75 OTG_HS_WKUP USB On The Go HS Wakeup through EXTI interrupt 76 OTG_HS USB On The Go HS global interrupt 77 PCGCR PCGCR Power and clock gating control register 0x0 0x20 read-write 0x00000000 STPPCLK Stop PHY clock 0 1 GATEHCLK Gate HCLK 1 1 PHYSUSP PHY suspended 4 1