STM32L4x6 2.0 STM32L4x6 CM4 r0p1 little true true 4 false 8 32 0x20 0x00000000 0xFFFFFFFF DAC Digital-to-analog converter DAC 0x40007400 0x0 0x400 registers CR CR control register 0x0 0x20 read-write 0x00000000 2 0x10 1-2 EN%s DAC channel%s enable 0 1 EN1 Disabled DAC Channel X disabled 0 Enabled DAC Channel X enabled 1 2 0x10 1-2 TEN%s DAC channel%s trigger enable 2 1 TEN1 Disabled DAC Channel X trigger disabled 0 Enabled DAC Channel X trigger enabled 1 TSEL1 DAC channel1 trigger selection 3 3 TSEL1 Tim6Trgo Timer 6 TRGO event 0 Tim8Trgo Timer 8 TRGO event 1 Tim5Trgo Timer 5 TRGO event 3 Tim2Trgo Timer 2 TRGO event 4 Tim4Trgo Timer 4 TRGO event 5 Exti9 External pin 6 Swtrig Software triger 7 2 0x10 1-2 WAVE%s DAC channel%s noise/triangle wave generation enable 6 2 WAVE1 Disabled Wave generation disabled 0 Noise Noise wave generation enabled 1 Triangle Triangle wave generation enabled true 2 0x10 1-2 MAMP%s DAC channel%s mask/amplitude selector 8 4 MAMP1 Amp1 Unmask bit0 of LFSR/ triangle amplitude equal to 1 0 Amp3 Unmask bits[1:0] of LFSR/ triangle amplitude equal to 3 1 Amp7 Unmask bits[2:0] of LFSR/ triangle amplitude equal to 7 2 Amp15 Unmask bits[3:0] of LFSR/ triangle amplitude equal to 15 3 Amp31 Unmask bits[4:0] of LFSR/ triangle amplitude equal to 31 4 Amp63 Unmask bits[5:0] of LFSR/ triangle amplitude equal 63 5 Amp127 Unmask bits[6:0] of LFSR/ triangle amplitude equal to 127 6 Amp255 Unmask bits[7:0] of LFSR/ triangle amplitude equal to 255 7 Amp511 Unmask bits[8:0] of LFSR/ triangle amplitude equal to 511 8 Amp1023 Unmask bits[9:0] of LFSR/ triangle amplitude equal to 1023 9 Amp2047 Unmask bits[10:0] of LFSR/ triangle amplitude equal to 2047 10 Amp4095 Unmask bits[11:0] of LFSR/ triangle amplitude equal to 4095 true 2 0x10 1-2 DMAEN%s DAC channel%s DMA enable 12 1 DMAEN1 Disabled DAC Channel X DMA mode disabled 0 Enabled DAC Channel X DMA mode enabled 1 2 0x10 1-2 DMAUDRIE%s DAC channel%s DMA Underrun Interrupt enable 13 1 DMAUDRIE1 Disabled DAC channel X DMA Underrun Interrupt disabled 0 Enabled DAC channel X DMA Underrun Interrupt enabled 1 2 0x10 1-2 CEN%s DAC channel%s calibration enable 14 1 CEN1 Normal DAC Channel X Normal operating mode 0 Calibration DAC Channel X calibration mode 1 TSEL2 DAC channel2 trigger selection 19 3 SWTRIGR SWTRIGR software trigger register 0x4 0x20 write-only 0x00000000 2 0x1 1-2 SWTRIG%s DAC channel%s software trigger 0 1 SWTRIG1 NoTrigger No trigger 0 Trigger Trigger 1 2 0xC 1-2 DHR12R%s DHR12R%s channel%s 12-bit right-aligned data holding register 0x8 0x20 read-write 0x00000000 DACCDHR DAC channel1 12-bit right-aligned data 0 12 0 4095 2 0xC 1-2 DHR12L%s DHR12L%s channel%s 12-bit left aligned data holding register 0xC 0x20 read-write 0x00000000 DACCDHR DAC channel1 12-bit left-aligned data 4 12 0 4095 2 0xC 1-2 DHR8R%s DHR8R%s channel%s 8-bit right aligned data holding register 0x10 0x20 read-write 0x00000000 DACCDHR DAC channel1 8-bit right-aligned data 0 8 0 255 DHR12RD DHR12RD Dual DAC 12-bit right-aligned data holding register 0x20 0x20 read-write 0x00000000 2 0x10 1-2 DACC%sDHR DAC channel%s 12-bit right-aligned data 0 12 0 4095 DHR12LD DHR12LD DUAL DAC 12-bit left aligned data holding register 0x24 0x20 read-write 0x00000000 2 0x10 1-2 DACC%sDHR DAC channel%s 12-bit left-aligned data 4 12 0 4095 DHR8RD DHR8RD DUAL DAC 8-bit right aligned data holding register 0x28 0x20 read-write 0x00000000 2 0x8 1-2 DACC%sDHR DAC channel%s 8-bit right-aligned data 0 8 0 255 2 0x4 1-2 DOR%s DOR%s channel%s data output register 0x2C 0x20 read-only 0x00000000 DACCDOR DAC channel1 data output 0 12 0 4095 SR SR status register 0x34 0x20 0x00000000 2 0x10 1-2 DMAUDR%s DAC channel%s DMA underrun flag 13 1 read-write DMAUDR1 NoUnderrun No DMA underrun error condition occurred for DAC channel x 0 Underrun DMA underrun error condition occurred for DAC channel x (the currently selected trigger is driving DAC channel1 conversion at a frequency higher than the DMA service capability rate) 1 2 0x10 1-2 CAL_FLAG%s DAC channel%s calibration offset status 14 1 read-only CAL_FLAG1 Lower Calibration trimming value is lower than the offset correction value 0 Equal_Higher Calibration trimming value is equal or greater than the offset correction value 1 2 0x10 1-2 BWST%s DAC channel%s busy writing sample time flag 15 1 read-only BWST1 Idle There is no write operation of DAC_SHSR1 ongoing: DAC_SHSR1 can be written 0 Busy There is a write operation of DAC_SHSR1 ongoing: DAC_SHSR1 cannot be written 1 CCR CCR calibration control register 0x38 0x20 read-write 0x00000000 2 0x10 1-2 OTRIM%s DAC channel%s offset trimming value 0 5 0 31 MCR MCR mode control register 0x3C 0x20 read-write 0x00000000 2 0x10 1-2 MODE%s DAC channel%s mode 0 3 MODE1 NormalPinBuffer Normal mode - DAC channelx is connected to external pin with Buffer enabled 0 NormalPinChipBuffer Normal mode - DAC channelx is connected to external pin and to on chip peripherals with Buffer enabled 1 NormalPinNoBuffer Normal mode - DAC channelx is connected to external pin with Buffer disabled 2 NormalChipNoBuffer Normal mode - DAC channelx is connected to on chip peripherals with Buffer disabled 3 SHPinBuffer S&H mode - DAC channelx is connected to external pin with Buffer enabled 4 SHPinChipBuffer S&H mode - DAC channelx is connected to external pin and to on chip peripherals with Buffer enabled 5 SHPinNoBuffer S&H mode - DAC channelx is connected to external pin and to on chip peripherals with Buffer disabled 6 SHChipNoBuffer S&H mode - DAC channelx is connected to on chip peripherals with Buffer disabled 7 2 0x4 1-2 SHSR%s SHSR%s DAC channel%s sample and hold sample time register 0x40 0x20 read-write 0x00000000 TSAMPLE DAC Channel 1 sample Time 0 10 0 1023 SHHR SHHR Sample and Hold hold time register 0x48 0x20 read-write 0x00010001 2 0x10 1-2 THOLD%s DAC channel%s hold time (only valid in Sample and hold mode) 0 10 0 1023 SHRR SHRR Sample and Hold refresh time register 0x4C 0x20 read-write 0x00000001 2 0x10 1-2 TREFRESH%s DAC channel%s refresh time (only valid in Sample and hold mode) 0 8 0 255 DMA1 Direct memory access controller DMA 0x40020000 0x0 0x400 registers DMA1_CH1 DMA1 Channel1 global interrupt 11 DMA1_CH2 DMA1 Channel2 global interrupt 12 DMA1_CH3 DMA1 Channel3 interrupt 13 DMA1_CH4 DMA1 Channel4 interrupt 14 DMA1_CH5 DMA1 Channel5 interrupt 15 DMA1_CH6 DMA1 Channel6 interrupt 16 DMA1_CH7 DMA1 Channel 7 interrupt 17 ISR ISR interrupt status register 0x0 0x20 read-only 0x00000000 7 0x4 1-7 TEIF%s Channel %s Transfer Error flag 3 1 TEIF1 NoError No transfer error 0 Error A transfer error has occured 1 7 0x4 1-7 HTIF%s Channel %s Half Transfer Complete flag 2 1 HTIF1 NotHalf No half transfer event 0 Half A half transfer event has occured 1 7 0x4 1-7 TCIF%s Channel %s Transfer Complete flag 1 1 TCIF1 NotComplete No transfer complete event 0 Complete A transfer complete event has occured 1 7 0x4 1-7 GIF%s Channel %s Global interrupt flag 0 1 GIF1 NoEvent No transfer error, half event, complete event 0 Event A transfer error, half event or complete event has occured 1 IFCR IFCR interrupt flag clear register 0x4 0x20 write-only 0x00000000 7 0x4 1-7 CTEIF%s Channel %s Transfer Error clear 3 1 CTEIF1 Clear Clears the TEIF flag in the ISR register 1 7 0x4 1-7 CHTIF%s Channel %s Half Transfer clear 2 1 CHTIF1 Clear Clears the HTIF flag in the ISR register 1 7 0x4 1-7 CTCIF%s Channel %s Transfer Complete clear 1 1 CTCIF1 Clear Clears the TCIF flag in the ISR register 1 7 0x4 1-7 CGIF%s Channel %s Global interrupt clear 0 1 CGIF1 Clear Clears the GIF, TEIF, HTIF, TCIF flags in the ISR register 1 7 0x14 1-7 CH%s Channel cluster: CCR?, CNDTR?, CPAR?, and CMAR? registers 0x8 CR CCR1 channel x configuration register 0x0 0x20 read-write 0x00000000 MEM2MEM Memory to memory mode 14 1 MEM2MEM Disabled Memory to memory mode disabled 0 Enabled Memory to memory mode enabled 1 PL Channel priority level 12 2 PL Low Low priority 0 Medium Medium priority 1 High High priority 2 VeryHigh Very high priority 3 PSIZE Peripheral size 8 2 PSIZE Bits8 8-bit size 0 Bits16 16-bit size 1 Bits32 32-bit size 2 MSIZE Memory size 10 2 PINC Peripheral increment mode 6 1 PINC Disabled Increment mode disabled 0 Enabled Increment mode enabled 1 MINC Memory increment mode 7 1 CIRC Circular mode 5 1 CIRC Disabled Circular buffer disabled 0 Enabled Circular buffer enabled 1 DIR Data transfer direction 4 1 DIR FromPeripheral Read from peripheral 0 FromMemory Read from memory 1 TEIE Transfer error interrupt enable 3 1 TEIE Disabled Transfer Error interrupt disabled 0 Enabled Transfer Error interrupt enabled 1 HTIE Half transfer interrupt enable 2 1 HTIE Disabled Half Transfer interrupt disabled 0 Enabled Half Transfer interrupt enabled 1 TCIE Transfer complete interrupt enable 1 1 TCIE Disabled Transfer Complete interrupt disabled 0 Enabled Transfer Complete interrupt enabled 1 EN Channel enable 0 1 EN Disabled Channel disabled 0 Enabled Channel enabled 1 NDTR CNDTR1 channel x number of data register 0x4 0x20 read-write 0x00000000 NDT Number of data to transfer 0 16 0 65535 PAR CPAR1 channel x peripheral address register 0x8 0x20 read-write 0x00000000 PA Peripheral address 0 32 MAR CMAR1 channel x memory address register 0xC 0x20 read-write 0x00000000 MA Memory address 0 32 CSELR CSELR channel selection register 0xA8 0x20 read-write 0x00000000 C1S DMA channel 1 selection 0 4 C1S NoMapping Default mapping 0 Map1 Mapping 1 1 Map2 Mapping 2 2 Map3 Mapping 3 3 Map4 Mapping 4 4 Map5 Mapping 5 5 Map6 Mapping 6 6 Map7 Mapping 7 7 Map8 Mapping 8 8 Map9 Mapping 9 9 Map10 Mapping 10 10 Map11 Mapping 11 11 Map12 Mapping 12 12 Map13 Mapping 13 13 Map14 Mapping 14 14 Map15 Mapping 15 15 C7S DMA channel 7 selection 24 4 C6S DMA channel 6 selection 20 4 C5S DMA channel 5 selection 16 4 C4S DMA channel 4 selection 12 4 C3S DMA channel 3 selection 8 4 C2S DMA channel 2 selection 4 4 DMA2 0x40020400 DMA2_CH1 DMA2 Channel 1 global Interrupt 56 DMA2_CH2 DMA2 Channel 2 global Interrupt 57 DMA2_CH3 DMA2 Channel 3 global Interrupt 58 DMA2_CH4 DMA2 Channel 4 global Interrupt 59 DMA2_CH5 DMA2 Channel 5 global Interrupt 60 DMA2_CH6 DMA2 Channel 6 global Interrupt 68 DMA2_CH7 DMA2 Channel 7 global Interrupt 69 CRC Cyclic redundancy check calculation unit CRC 0x40023000 0x0 0x400 registers DR DR Data register 0x0 0x20 read-write 0xFFFFFFFF DR Data register bits 0 32 0 4294967295 DR8 Data register - byte sized DR 0x0 0x8 read-write 0x000000FF DR8 Data register bits 0 8 0 255 DR16 Data register - half-word sized DR 0x0 0x10 read-write 0x0000FFFF DR16 Data register bits 0 16 0 65535 IDR IDR Independent data register 0x4 0x20 read-write 0x00000000 IDR General-purpose 8-bit data register bits 0 8 0 255 CR CR Control register 0x8 0x20 0x00000000 REV_OUT Reverse output data 7 1 read-write REV_OUT Normal Bit order not affected 0 Reversed Bit reversed output 1 REV_IN Reverse input data 5 2 read-write REV_IN Normal Bit order not affected 0 Byte Bit reversal done by byte 1 HalfWord Bit reversal done by half-word 2 Word Bit reversal done by word 3 POLYSIZE Polynomial size 3 2 read-write POLYSIZE Polysize32 32-bit polynomial 0 Polysize16 16-bit polynomial 1 Polysize8 8-bit polynomial 2 Polysize7 7-bit polynomial 3 RESET RESET bit 0 1 write-only RESETW Reset Resets the CRC calculation unit and sets the data register to 0xFFFF FFFF 1 INIT INIT Initial CRC value 0x10 0x20 read-write 0xFFFFFFFF INIT Programmable initial CRC value 0 32 0 4294967295 POL POL polynomial 0x14 0x20 read-write 0x04C11DB7 POL Programmable polynomial 0 32 0 4294967295 LCD Liquid crystal display controller LCD 0x40002400 0x0 0x400 registers LCD LCD global interrupt 78 CR CR LCD control register 0x0 0x20 0x00000000 0xFFFFFFFF LCDEN LCD controller enable This bit is set by software to enable the LCD Controller/Driver. It is cleared by software to turn off the LCD at the beginning of the next frame. When the LCD is disabled all COM and SEG pins are driven to V_SS. 0 1 read-write VSEL Voltage source selection The VSEL bit determines the voltage source for the LCD. 1 1 read-write DUTY Duty selection These bits determine the duty cycle.Unused COM pins can serve as general purpose input pins if COMIN is set. Values 101, 110 and 111 are forbidden. Others: Reserved 2 3 read-write BIAS Bias selector These bits determine the bias used. Value 11 is forbidden. 5 2 read-write MUX_SEG Mux segment enable This bit is used to enable SEG pin remapping. Four SEG pins can be multiplexed with SEG[31:28] or SEG[15:12]. See Section19.3.7. 7 1 read-write BUFEN Voltage output buffer enable This bit is used to enable/disable the voltage output buffer for higher driving capability. 8 1 read-write FCR FCR LCD frame control register 0x4 0x20 0x00000000 0xFFFFFFFF HD High drive enable This bit is written by software to enable a low resistance divider. Displays with high internal resistance may need a longer drive time to achieve satisfactory contrast. This bit is useful in this case if some additional power consumption can be tolerated. 0 1 read-write SOFIE Start of frame interrupt enable This bit is set and cleared by software. 1 1 read-write UDDIE Update display done interrupt enable This bit is set and cleared by software. 3 1 read-write PON Pulse ON duration These bits are written by software to define the pulse duration in terms of ck_ps pulses. Ashort pulse leads to lower power consumption, but displays with high internal resistance may need a longer pulse to achieve satisfactory contrast. Note that the pulse is never longer than one half prescaled LCD clock period. PON duration example with LCDCLK = 32.768kHz and PS=0x03: 4 3 read-write DEAD Dead time duration These bits are written by software to configure the length of the dead time between frames. During the dead time the COM and SEG voltage levels are held at 0 V to reduce the contrast without modifying the frame rate. ...... 7 3 read-write CC Contrast control 10 3 read-write BLINKF Blink frequency selection 13 3 read-write BLINK Blink mode selection 16 2 read-write DIV DIV clock divider 18 4 read-write PS PS 16-bit prescaler 22 4 read-write SR SR LCD status register 0x8 0x20 0x00000020 0xFFFFFFFF ENS LCD enabled status This bit is set and cleared by hardware. It indicates the LCD controller status. The ENS bit is set immediately when the LCDEN bit in the LCD_CR goes from 0 to 1. On deactivation it reflects the real status of LCD so it becomes 0 at the end of the last displayed frame. 0 1 read-only SOF Start-of-frame flag This bit is set by hardware at the beginning of a new frame, at the same time as the display data is updated. It is cleared by writing a 1 to the SOFC bit in the LCD_CLR register. The bit clear has priority over the set. 1 1 read-only UDR Update display request 2 1 read-write UDD Update display done This bit is set by hardware. It is cleared by writing 1 to the UDDC bit in the LCD_CLR register. The bit set has priority over the clear. If the device is in Stop mode (PCLK not provided), UDD does not generate an interrupt even if UDDIE = 1. If the display is not enabled the UDD interrupt never occurs. 3 1 read-only RDY Ready flag This bit is set and cleared by hardware. It indicates the status of the step-up converter. 4 1 read-only FCRSF LCD frame control register synchronization flag This bit is set by hardware each time the LCD_FCR register is updated in the LCDCLK domain. It is cleared by hardware when writing to the LCD_FCR register. 5 1 read-only CLR CLR LCD clear register 0xC 0x20 0x00000000 0xFFFFFFFF SOFC Start of frame flag clear This bit is written by software to clear the SOF flag in the LCD_SR register. 1 1 write-only UDDC Update display done clear This bit is written by software to clear the UDD flag in the LCD_SR register. 3 1 write-only RAM_COM0 RAM_COM0 LCD display memory 0x14 0x40 read-write 0x00000000 SEGS Segment states, one bit per segment, LSB: S00, MSB: S39 0 40 RAM_COM4 RAM_COM4 LCD display memory 0x34 0x40 read-write 0x00000000 SEGS Segment states, one bit per segment, LSB: S00, MSB: S43 0 44 RAM_COM1 0x1C RAM_COM2 0x24 RAM_COM3 0x2C RAM_COM5 0x3C RAM_COM6 0x44 RAM_COM7 0x4C TSC Touch sensing controller TSC 0x40024000 0x0 0x400 registers TSC TSC global interrupt 77 CR CR control register 0x0 0x20 read-write 0x00000000 CTPH Charge transfer pulse high 28 4 CTPL Charge transfer pulse low 24 4 SSD Spread spectrum deviation 17 7 SSE Spread spectrum enable 16 1 SSE Disabled Spread spectrum disabled 0 Enabled Spread spectrum enabled 1 SSPSC Spread spectrum prescaler 15 1 PGPSC pulse generator prescaler 12 3 MCV Max count value 5 3 IODEF I/O Default mode 4 1 IODEF PushPull I/Os are forced to output push-pull low 0 Floating I/Os are in input floating 1 SYNCPOL Synchronization pin polarity 3 1 SYNCPOL FallingEdge Falling edge only 0 RisingEdge Rising edge and high level 1 AM Acquisition mode 2 1 AM Normal Normal acquisition mode (acquisition starts as soon as START bit is set) 0 Synchronized Synchronized acquisition mode (acquisition starts if START bit is set and when the selected signal is detected on the SYNC input pin) 1 START Start a new acquisition 1 1 START NoStarted Acquisition not started 0 Started Start a new acquisition 1 TSCE Touch sensing controller enable 0 1 TSCE Disabled Touch sensing controller disabled 0 Enabled Touch sensing controller enabled 1 IER IER interrupt enable register 0x4 0x20 read-write 0x00000000 MCEIE Max count error interrupt enable 1 1 MCEIE Disabled Max count error interrupt disabled 0 Enabled Max count error interrupt enabled 1 EOAIE End of acquisition interrupt enable 0 1 EOAIE Disabled End of acquisition interrupt disabled 0 Enabled End of acquisition interrupt enabled 1 ICR ICR interrupt clear register 0x8 0x20 read-write 0x00000000 MCEIC Max count error interrupt clear 1 1 EOAIC End of acquisition interrupt clear 0 1 ISR ISR interrupt status register 0xC 0x20 read-write 0x00000000 MCEF Max count error flag 1 1 EOAF End of acquisition flag 0 1 IOHCR IOHCR I/O hysteresis control register 0x10 0x20 read-write 0xFFFFFFFF 8 0x4 1-8 G%s_IO1 G%s_IO1 0 1 G1_IO1 Disabled Gx_IOy Schmitt trigger hysteresis disabled 0 Enabled Gx_IOy Schmitt trigger hysteresis enabled 1 8 0x4 1-8 G%s_IO4 G%s_IO4 3 1 8 0x4 1-8 G%s_IO3 G%s_IO3 2 1 8 0x4 1-8 G%s_IO2 G%s_IO2 1 1 IOASCR IOASCR I/O analog switch control register 0x18 0x20 read-write 0x00000000 8 0x4 1-8 G%s_IO1 G%s_IO1 0 1 G1_IO1 Disabled Gx_IOy analog switch disabled (opened) 0 Enabled Gx_IOy analog switch enabled (closed) 1 8 0x4 1-8 G%s_IO4 G%s_IO4 3 1 8 0x4 1-8 G%s_IO3 G%s_IO3 2 1 8 0x4 1-8 G%s_IO2 G%s_IO2 1 1 IOSCR IOSCR I/O sampling control register 0x20 0x20 read-write 0x00000000 8 0x4 1-8 G%s_IO1 G%s_IO1 0 1 G1_IO1 Disabled Gx_IOy unused 0 Enabled Gx_IOy used as sampling capacitor 1 8 0x4 1-8 G%s_IO4 G%s_IO4 3 1 8 0x4 1-8 G%s_IO3 G%s_IO3 2 1 8 0x4 1-8 G%s_IO2 G%s_IO2 1 1 IOCCR IOCCR I/O channel control register 0x28 0x20 read-write 0x00000000 8 0x4 1-8 G%s_IO1 G%s_IO1 0 1 G1_IO1 Disabled Gx_IOy unused 0 Enabled Gx_IOy used as channel 1 8 0x4 1-8 G%s_IO4 G%s_IO4 3 1 8 0x4 1-8 G%s_IO3 G%s_IO3 2 1 8 0x4 1-8 G%s_IO2 G%s_IO2 1 1 IOGCSR IOGCSR I/O group control status register 0x30 0x20 0x00000000 8 0x1 1-8 G%sS Analog I/O group x status 16 1 read-only G1S Ongoing Acquisition on analog I/O group x is ongoing or not started 0 Complete Acquisition on analog I/O group x is complete 1 8 0x1 1-8 G%sE Analog I/O group x enable 0 1 read-write G1E Disabled Acquisition on analog I/O group x disabled 0 Enabled Acquisition on analog I/O group x enabled 1 8 0x4 1-8 IOG%sCR IOG%sCR I/O group x counter register 0x34 0x20 read-only 0x00000000 CNT Counter value 0 14 IWDG Independent watchdog IWDG 0x40003000 0x0 0x400 registers KR KR Key register 0x0 0x10 write-only 0x00000000 KEY Key value (write only, read 0x0000) 0 16 KEY Unlock Enable access to PR, RLR and WINR registers 21845 Feed Feed watchdog with RLR register value 43690 Start Start the watchdog 52428 PR PR Prescaler register 0x4 0x10 read-write 0x00000000 PR Prescaler divider 0 3 PR DivideBy4 Divider /4 0 DivideBy8 Divider /8 1 DivideBy16 Divider /16 2 DivideBy32 Divider /32 3 DivideBy64 Divider /64 4 DivideBy128 Divider /128 5 DivideBy256 Divider /256 true RLR RLR Reload register 0x8 0x10 read-write 0x00000FFF RL Watchdog counter reload value 0 12 0 4095 SR SR Status register 0xC 0x10 read-only 0x00000000 WVU Watchdog counter window value update 2 1 RVU Watchdog counter reload value update 1 1 PVU Watchdog prescaler value update 0 1 WINR WINR Window register 0x10 0x10 read-write 0x00000FFF WIN Watchdog counter window value 0 12 0 4095 WWDG System window watchdog WWDG 0x40002C00 0x0 0x400 registers WWDG Window Watchdog interrupt 0 CR CR Control register 0x0 0x10 read-write 0x0000007F WDGA Activation bit 7 1 WDGA Disabled Watchdog disabled 0 Enabled Watchdog enabled 1 T 7-bit counter (MSB to LSB) 0 7 0 127 CFR CFR Configuration register 0x4 0x10 read-write 0x0000007F EWI Early wakeup interrupt 9 1 EWIW write Enable interrupt occurs whenever the counter reaches the value 0x40 1 WDGTB Timer base 7 2 WDGTB Div1 Counter clock (PCLK1 div 4096) div 1 0 Div2 Counter clock (PCLK1 div 4096) div 2 1 Div4 Counter clock (PCLK1 div 4096) div 4 2 Div8 Counter clock (PCLK1 div 4096) div 8 3 W 7-bit window value 0 7 0 127 SR SR Status register 0x8 0x10 read-write 0x00000000 EWIF Early wakeup interrupt flag 0 1 zeroToClear EWIFR read Finished The EWI Interrupt Service Routine has been serviced 0 Pending The EWI Interrupt Service Routine has been triggered 1 EWIFW write Finished The EWI Interrupt Service Routine has been serviced 0 COMP Comparator COMP 0x40010200 0x0 0x200 registers COMP COMP1 and COMP2 interrupts 64 COMP1_CSR COMP1_CSR Comparator 1 control and status register 0x0 0x20 0x00000000 EN Comparator 1 enable bit 0 1 read-write EN Disabled Comparator X disabled 0 Enabled Comparator X enabled 1 PWRMODE Power Mode of the comparator 1 2 2 read-write PWRMODE HighSpeed High speed / full power 0 MediumSpeed Medium speed / medium power 1 LowSpeed Low speed / ultra-low power 3 INMSEL Comparator 1 Input Minus connection configuration bit 4 3 read-write INMSEL OneQuarterVRef 1/4 of VRefint 0 OneHalfVRef 1/2 of VRefint 1 ThreeQuarterVRef 3/4 of VRefint 2 VRef VRefint 3 DAC_CH1 DAC Channel 1 4 DAC_CH2 DAC Channel 2 5 PC4 PC4 6 INPSEL Comparator1 input plus selection bit 7 1 read-write INPSEL PC5 PC5 connected to input plus 0 PB2 PB2 connected to input plus 1 POLARITY Comparator 1 polarity selection bit 15 1 read-write POLARITY Normal Comparator X output value not inverted 0 Inverted Comparator X output value inverted 1 HYST Comparator 1 hysteresis selection bits 16 2 read-write HYST None No hysteresis 0 Low Low hysteresis 1 Medium Medium hysteresis 2 High High hysteresis 3 BLANKING Comparator 1 blanking source selection bits 18 3 read-write BLANKING NoBlanking No blanking 0 TIM1OC5 TIM15 OC1 selected as blanking source 4 BRGEN Scaler bridge enable 22 1 read-write BRGEN Disabled Scaler resistor bridge disabled 0 Enabled Scaler resistor bridge enabled 1 SCALEN Voltage scaler enable bit 23 1 read-write SCALEN Disabled Voltage scaler disabled 0 Enabled Voltage scaler enabled 1 VALUE Comparator 1 output status bit 30 1 read-only VALUE Low Comparator output is low 0 High Comparator output is high 1 LOCK COMP1_CSR register lock bit 31 1 write-only LOCK Unlocked Comparator CSR bits are read-write 0 Locked Comparator CSR bits are read-only 1 COMP2_CSR COMP2_CSR Comparator 2 control and status register 0x4 0x20 0x00000000 EN Comparator 2 enable bit 0 1 read-write EN Disabled Comparator X disabled 0 Enabled Comparator X enabled 1 PWRMODE Power Mode of the comparator 2 2 2 read-write PWRMODE HighSpeed High speed / full power 0 MediumSpeed Medium speed / medium power 1 LowSpeed Low speed / ultra-low power 3 INMSEL Comparator 2 Input Minus connection configuration bit 4 3 read-write INMSEL OneQuarterVRef 1/4 of VRefint 0 OneHalfVRef 1/2 of VRefint 1 ThreeQuarterVRef 3/4 of VRefint 2 VRef VRefint 3 DAC_CH1 DAC Channel 1 4 DAC_CH2 DAC Channel 2 5 PB3 PB3 6 PB7 PB7 7 INPSEL Comparator 2 Input Plus connection configuration bit 7 1 read-write INPSEL PB4 PB4 connected to input plus 0 PB6 PB6 connected to input plus 1 WINMODE Windows mode selection bit 9 1 read-write WINMODE Disabled COMP2 input plus is not connected to COMP1 0 Enabled COMP2 input plus is connected to COMP1 1 POLARITY Comparator 2 polarity selection bit 15 1 read-write POLARITY Normal Comparator X output value not inverted 0 Inverted Comparator X output value inverted 1 HYST Comparator 2 hysteresis selection bits 16 2 read-write HYST None No hysteresis 0 Low Low hysteresis 1 Medium Medium hysteresis 2 High High hysteresis 3 BLANKING Comparator 2 blanking source selection bits 18 3 read-write BLANKING NoBlanking No blanking 0 TIM1OC5 TIM15 OC1 selected as blanking source 4 BRGEN Scaler bridge enable 22 1 read-write BRGEN Disabled Scaler resistor bridge disabled 0 Enabled Scaler resistor bridge enabled 1 SCALEN Voltage scaler enable bit 23 1 read-write SCALEN Disabled Voltage scaler disabled 0 Enabled Voltage scaler enabled 1 VALUE Comparator 2 output status bit 30 1 read-only VALUE Low Comparator output is low 0 High Comparator output is high 1 LOCK COMP2_CSR register lock bit 31 1 write-only LOCK Unlocked Comparator CSR bits are read-write 0 Locked Comparator CSR bits are read-only 1 FIREWALL Firewall Firewall 0x40011C00 0x0 0x400 registers CSSA CSSA Code segment start address 0x0 0x20 read-write 0x00000000 ADD code segment start address 8 16 0 65535 CSL CSL Code segment length 0x4 0x20 read-write 0x00000000 LENG code segment length 8 14 0 16383 NVDSSA NVDSSA Non-volatile data segment start address 0x8 0x20 read-write 0x00000000 ADD Non-volatile data segment start address 8 16 0 65535 NVDSL NVDSL Non-volatile data segment length 0xC 0x20 read-write 0x00000000 LENG Non-volatile data segment length 8 14 0 16383 VDSSA VDSSA Volatile data segment start address 0x10 0x20 read-write 0x00000000 ADD Volatile data segment start address 6 10 0 1023 VDSL VDSL Volatile data segment length 0x14 0x20 read-write 0x00000000 LENG Non-volatile data segment length 6 10 0 1023 CR CR Configuration register 0x20 0x20 read-write 0x00000000 VDE Volatile data execution 2 1 VDER read NotExecutable Volatile data segment cannot be executed if VDS = 0 0 Executable Volatile data segment is declared executable whatever VDS bit value 1 VDEW write Reset Resets volatile data execution bit 0 VDS Volatile data shared 1 1 VDSR read NotShared Volatile data segment is not shared and cannot be hit by a non protected executable code when the Firewall is closed 0 Shared Volatile data segment is shared with non protected application code 1 VDSW write Reset Resets volatile data shared bit 0 FPA Firewall pre alarm 0 1 FPAW write PreArmReset Any code executed outside the protected segment when the Firewall is opened will generate a system reset 0 PreArmSet Any code executed outside the protected segment will close the Firewall 1 I2C1 Inter-integrated circuit I2C 0x40005400 0x0 0x400 registers I2C1_EV I2C1 event interrupt 31 I2C1_ER I2C1 error interrupt 32 CR1 CR1 Control register 1 0x0 0x20 read-write 0x00000000 PE Peripheral enable 0 1 PE Disabled Peripheral disabled 0 Enabled Peripheral enabled 1 TXIE TX Interrupt enable 1 1 TXIE Disabled Transmit (TXIS) interrupt disabled 0 Enabled Transmit (TXIS) interrupt enabled 1 RXIE RX Interrupt enable 2 1 RXIE Disabled Receive (RXNE) interrupt disabled 0 Enabled Receive (RXNE) interrupt enabled 1 ADDRIE Address match interrupt enable (slave only) 3 1 ADDRIE Disabled Address match (ADDR) interrupts disabled 0 Enabled Address match (ADDR) interrupts enabled 1 NACKIE Not acknowledge received interrupt enable 4 1 NACKIE Disabled Not acknowledge (NACKF) received interrupts disabled 0 Enabled Not acknowledge (NACKF) received interrupts enabled 1 STOPIE STOP detection Interrupt enable 5 1 STOPIE Disabled Stop detection (STOPF) interrupt disabled 0 Enabled Stop detection (STOPF) interrupt enabled 1 TCIE Transfer Complete interrupt enable 6 1 TCIE Disabled Transfer Complete interrupt disabled 0 Enabled Transfer Complete interrupt enabled 1 ERRIE Error interrupts enable 7 1 ERRIE Disabled Error detection interrupts disabled 0 Enabled Error detection interrupts enabled 1 DNF Digital noise filter 8 4 DNF NoFilter Digital filter disabled 0 Filter1 Digital filter enabled and filtering capability up to 1 tI2CCLK 1 Filter2 Digital filter enabled and filtering capability up to 2 tI2CCLK 2 Filter3 Digital filter enabled and filtering capability up to 3 tI2CCLK 3 Filter4 Digital filter enabled and filtering capability up to 4 tI2CCLK 4 Filter5 Digital filter enabled and filtering capability up to 5 tI2CCLK 5 Filter6 Digital filter enabled and filtering capability up to 6 tI2CCLK 6 Filter7 Digital filter enabled and filtering capability up to 7 tI2CCLK 7 Filter8 Digital filter enabled and filtering capability up to 8 tI2CCLK 8 Filter9 Digital filter enabled and filtering capability up to 9 tI2CCLK 9 Filter10 Digital filter enabled and filtering capability up to 10 tI2CCLK 10 Filter11 Digital filter enabled and filtering capability up to 11 tI2CCLK 11 Filter12 Digital filter enabled and filtering capability up to 12 tI2CCLK 12 Filter13 Digital filter enabled and filtering capability up to 13 tI2CCLK 13 Filter14 Digital filter enabled and filtering capability up to 14 tI2CCLK 14 Filter15 Digital filter enabled and filtering capability up to 15 tI2CCLK 15 ANFOFF Analog noise filter OFF 12 1 ANFOFF Enabled Analog noise filter enabled 0 Disabled Analog noise filter disabled 1 TXDMAEN DMA transmission requests enable 14 1 TXDMAEN Disabled DMA mode disabled for transmission 0 Enabled DMA mode enabled for transmission 1 RXDMAEN DMA reception requests enable 15 1 RXDMAEN Disabled DMA mode disabled for reception 0 Enabled DMA mode enabled for reception 1 SBC Slave byte control 16 1 SBC Disabled Slave byte control disabled 0 Enabled Slave byte control enabled 1 NOSTRETCH Clock stretching disable 17 1 NOSTRETCH Enabled Clock stretching enabled 0 Disabled Clock stretching disabled 1 WUPEN Wakeup from STOP enable 18 1 WUPEN Disabled Wakeup from Stop mode disabled 0 Enabled Wakeup from Stop mode enabled 1 GCEN General call enable 19 1 GCEN Disabled General call disabled. Address 0b00000000 is NACKed 0 Enabled General call enabled. Address 0b00000000 is ACKed 1 SMBHEN SMBus Host address enable 20 1 SMBHEN Disabled Host address disabled. Address 0b0001000x is NACKed 0 Enabled Host address enabled. Address 0b0001000x is ACKed 1 SMBDEN SMBus Device Default address enable 21 1 SMBDEN Disabled Device default address disabled. Address 0b1100001x is NACKed 0 Enabled Device default address enabled. Address 0b1100001x is ACKed 1 ALERTEN SMBUS alert enable 22 1 ALERTEN Disabled In device mode (SMBHEN=Disabled) Releases SMBA pin high and Alert Response Address Header disabled (0001100x) followed by NACK. In host mode (SMBHEN=Enabled) SMBus Alert pin (SMBA) not supported 0 Enabled In device mode (SMBHEN=Disabled) Drives SMBA pin low and Alert Response Address Header enabled (0001100x) followed by ACK.In host mode (SMBHEN=Enabled) SMBus Alert pin (SMBA) supported 1 PECEN PEC enable 23 1 PECEN Disabled PEC calculation disabled 0 Enabled PEC calculation enabled 1 CR2 CR2 Control register 2 0x4 0x20 read-write 0x00000000 PECBYTE Packet error checking byte 26 1 oneToSet PECBYTER read NoPec No PEC transfer 0 Pec PEC transmission/reception is requested 1 PECBYTEW write Pec PEC transmission/reception is requested 1 AUTOEND Automatic end mode (master mode) 25 1 AUTOEND Software Software end mode: TC flag is set when NBYTES data are transferred, stretching SCL low 0 Automatic Automatic end mode: a STOP condition is automatically sent when NBYTES data are transferred 1 RELOAD NBYTES reload mode 24 1 RELOAD Completed The transfer is completed after the NBYTES data transfer (STOP or RESTART will follow) 0 NotCompleted The transfer is not completed after the NBYTES data transfer (NBYTES will be reloaded) 1 NBYTES Number of bytes 16 8 0 255 NACK NACK generation (slave mode) 15 1 oneToSet NACKR read Ack an ACK is sent after current received byte 0 Nack a NACK is sent after current received byte 1 NACKW write Nack a NACK is sent after current received byte 1 STOP Stop generation (master mode) 14 1 oneToSet STOPR read NoStop No Stop generation 0 Stop Stop generation after current byte transfer 1 STOPW write Stop Stop generation after current byte transfer 1 START Start generation 13 1 oneToSet STARTR read NoStart No Start generation 0 Start Restart/Start generation 1 STARTW write Start Restart/Start generation 1 HEAD10R 10-bit address header only read direction (master receiver mode) 12 1 HEAD10R Complete The master sends the complete 10 bit slave address read sequence 0 Partial The master only sends the 1st 7 bits of the 10 bit address, followed by Read direction 1 ADD10 10-bit addressing mode (master mode) 11 1 ADD10 Bit7 The master operates in 7-bit addressing mode 0 Bit10 The master operates in 10-bit addressing mode 1 RD_WRN Transfer direction (master mode) 10 1 RD_WRN Write Master requests a write transfer 0 Read Master requests a read transfer 1 SADD Slave address bit (master mode) 0 10 0 1023 OAR1 OAR1 Own address register 1 0x8 0x20 read-write 0x00000000 OA1 Interface address 0 10 0 1023 OA1MODE Own Address 1 10-bit mode 10 1 OA1MODE Bit7 Own address 1 is a 7-bit address 0 Bit10 Own address 1 is a 10-bit address 1 OA1EN Own Address 1 enable 15 1 OA1EN Disabled Own address 1 disabled. The received slave address OA1 is NACKed 0 Enabled Own address 1 enabled. The received slave address OA1 is ACKed 1 OAR2 OAR2 Own address register 2 0xC 0x20 read-write 0x00000000 OA2 Interface address 1 7 0 127 OA2MSK Own Address 2 masks 8 3 OA2MSK NoMask No mask 0 Mask1 OA2[1] is masked and don’t care. Only OA2[7:2] are compared 1 Mask2 OA2[2:1] are masked and don’t care. Only OA2[7:3] are compared 2 Mask3 OA2[3:1] are masked and don’t care. Only OA2[7:4] are compared 3 Mask4 OA2[4:1] are masked and don’t care. Only OA2[7:5] are compared 4 Mask5 OA2[5:1] are masked and don’t care. Only OA2[7:6] are compared 5 Mask6 OA2[6:1] are masked and don’t care. Only OA2[7] is compared. 6 Mask7 OA2[7:1] are masked and don’t care. No comparison is done, and all (except reserved) 7-bit received addresses are acknowledged 7 OA2EN Own Address 2 enable 15 1 OA2EN Disabled Own address 2 disabled. The received slave address OA2 is NACKed 0 Enabled Own address 2 enabled. The received slave address OA2 is ACKed 1 TIMINGR TIMINGR Timing register 0x10 0x20 read-write 0x00000000 SCLL SCL low period (master mode) 0 8 0 255 SCLH SCL high period (master mode) 8 8 0 255 SDADEL Data hold time 16 4 0 15 SCLDEL Data setup time 20 4 0 15 PRESC Timing prescaler 28 4 0 15 TIMEOUTR TIMEOUTR Status register 1 0x14 0x20 read-write 0x00000000 TIMEOUTA Bus timeout A 0 12 0 4095 TIDLE Idle clock timeout detection 12 1 TIDLE Disabled TIMEOUTA is used to detect SCL low timeout 0 Enabled TIMEOUTA is used to detect both SCL and SDA high timeout (bus idle condition) 1 TIMOUTEN Clock timeout enable 15 1 TIMOUTEN Disabled SCL timeout detection is disabled 0 Enabled SCL timeout detection is enabled 1 TIMEOUTB Bus timeout B 16 12 0 4095 TEXTEN Extended clock timeout enable 31 1 TEXTEN Disabled Extended clock timeout detection is disabled 0 Enabled Extended clock timeout detection is enabled 1 ISR ISR Interrupt and Status register 0x18 0x20 0x00000001 ADDCODE Address match code (Slave mode) 17 7 read-only 0 127 DIR Transfer direction (Slave mode) 16 1 read-only DIR Write Write transfer, slave enters receiver mode 0 Read Read transfer, slave enters transmitter mode 1 BUSY Bus busy 15 1 read-only BUSY NotBusy No communication is in progress on the bus 0 Busy A communication is in progress on the bus 1 ALERT SMBus alert 13 1 read-only ALERT NoAlert SMBA alert is not detected 0 Alert SMBA alert event is detected on SMBA pin 1 TIMEOUT Timeout or t_low detection flag 12 1 read-only TIMEOUT NoTimeout No timeout occured 0 Timeout Timeout occured 1 PECERR PEC Error in reception 11 1 read-only PECERR Match Received PEC does match with PEC register 0 NoMatch Received PEC does not match with PEC register 1 OVR Overrun/Underrun (slave mode) 10 1 read-only OVR NoOverrun No overrun/underrun error occurs 0 Overrun slave mode with NOSTRETCH=1, when an overrun/underrun error occurs 1 ARLO Arbitration lost 9 1 read-only ARLO NotLost No arbitration lost 0 Lost Arbitration lost 1 BERR Bus error 8 1 read-only BERR NoError No bus error 0 Error Misplaced Start and Stop condition is detected 1 TCR Transfer Complete Reload 7 1 read-only TCR NotComplete Transfer is not complete 0 Complete NBYTES has been transfered 1 TC Transfer Complete (master mode) 6 1 read-only TC NotComplete Transfer is not complete 0 Complete NBYTES has been transfered 1 STOPF Stop detection flag 5 1 read-only STOPF NoStop No Stop condition detected 0 Stop Stop condition detected 1 NACKF Not acknowledge received flag 4 1 read-only NACKF NoNack No NACK has been received 0 Nack NACK has been received 1 ADDR Address matched (slave mode) 3 1 read-only ADDR NotMatch Adress mismatched or not received 0 Match Received slave address matched with one of the enabled slave addresses 1 RXNE Receive data register not empty (receivers) 2 1 read-only RXNE Empty The RXDR register is empty 0 NotEmpty Received data is copied into the RXDR register, and is ready to be read 1 TXIS Transmit interrupt status (transmitters) 1 1 read-write oneToSet TXISR read NotEmpty The TXDR register is not empty 0 Empty The TXDR register is empty and the data to be transmitted must be written in the TXDR register 1 TXISW write Trigger Generate a TXIS event 1 TXE Transmit data register empty (transmitters) 0 1 read-write oneToSet TXER read NotEmpty TXDR register not empty 0 Empty TXDR register empty 1 TXEW write Flush Flush the transmit data register 1 ICR ICR Interrupt clear register 0x1C 0x20 write-only 0x00000000 ALERTCF Alert flag clear 13 1 oneToClear ALERTCF Clear Clears the ALERT flag in ISR register 1 TIMOUTCF Timeout detection flag clear 12 1 oneToClear TIMOUTCF Clear Clears the TIMOUT flag in ISR register 1 PECCF PEC Error flag clear 11 1 oneToClear PECCF Clear Clears the PEC flag in ISR register 1 OVRCF Overrun/Underrun flag clear 10 1 oneToClear OVRCF Clear Clears the OVR flag in ISR register 1 ARLOCF Arbitration lost flag clear 9 1 oneToClear ARLOCF Clear Clears the ARLO flag in ISR register 1 BERRCF Bus error flag clear 8 1 oneToClear BERRCF Clear Clears the BERR flag in ISR register 1 STOPCF Stop detection flag clear 5 1 oneToClear STOPCF Clear Clears the STOP flag in ISR register 1 NACKCF Not Acknowledge flag clear 4 1 oneToClear NACKCF Clear Clears the NACK flag in ISR register 1 ADDRCF Address Matched flag clear 3 1 oneToClear ADDRCF Clear Clears the ADDR flag in ISR register 1 PECR PECR PEC register 0x20 0x20 read-only 0x00000000 PEC Packet error checking register 0 8 0 255 RXDR RXDR Receive data register 0x24 0x20 read-only 0x00000000 RXDATA 8-bit receive data 0 8 0 255 TXDR TXDR Transmit data register 0x28 0x20 read-write 0x00000000 TXDATA 8-bit transmit data 0 8 0 255 I2C2 0x40005800 I2C2_EV I2C2 event interrupt 33 I2C2_ER I2C2 error interrupt 34 I2C3 0x40005C00 I2C3_EV I2C3 event interrupt 72 I2C3_ER I2C3 error interrupt 73 I2C4 0x40008400 I2C4_EV I2C4 event interrupt 83 I2C4_ER I2C4 error interrupt 84 FLASH Flash Flash 0x40022000 0x0 0x400 registers FLASH Flash global interrupt 4 ACR ACR Access control register 0x0 0x20 read-write 0x00000600 LATENCY Latency 0 3 PRFTEN Prefetch enable 8 1 ICEN Instruction cache enable 9 1 DCEN Data cache enable 10 1 ICRST Instruction cache reset 11 1 DCRST Data cache reset 12 1 RUN_PD Flash Power-down mode during Low-power run mode 13 1 SLEEP_PD Flash Power-down mode during Low-power sleep mode 14 1 PDKEYR PDKEYR Power down key register 0x4 0x20 write-only 0x00000000 PDKEYR RUN_PD in FLASH_ACR key 0 32 KEYR KEYR Flash key register 0x8 0x20 write-only 0x00000000 KEYR KEYR 0 32 OPTKEYR OPTKEYR Option byte key register 0xC 0x20 write-only 0x00000000 OPTKEYR Option byte key 0 32 SR SR Status register 0x10 0x20 0x00000000 EOP End of operation 0 1 read-write OPERR Operation error 1 1 read-write PROGERR Programming error 3 1 read-write WRPERR Write protected error 4 1 read-write PGAERR Programming alignment error 5 1 read-write SIZERR Size error 6 1 read-write PGSERR Programming sequence error 7 1 read-write MISERR Fast programming data miss error 8 1 read-write FASTERR Fast programming error 9 1 read-write RDERR PCROP read error 14 1 read-write OPTVERR Option validity error 15 1 read-write BSY Busy 16 1 read-only CR CR Flash control register 0x14 0x20 read-write 0xC0000000 PG Programming 0 1 PER Page erase 1 1 MER1 Bank 1 Mass erase 2 1 PNB Page number 3 8 BKER Bank erase 11 1 MER2 Bank 2 Mass erase 15 1 START Start 16 1 OPTSTRT Options modification start 17 1 FSTPG Fast programming 18 1 EOPIE End of operation interrupt enable 24 1 ERRIE Error interrupt enable 25 1 RDERRIE PCROP read error interrupt enable 26 1 OBL_LAUNCH Force the option byte loading 27 1 OPTLOCK Options Lock 30 1 LOCK FLASH_CR Lock 31 1 ECCR ECCR Flash ECC register 0x18 0x20 0x00000000 ADDR_ECC ECC fail address 0 19 read-only BK_ECC ECC fail bank 19 1 read-only SYSF_ECC System Flash ECC fail 20 1 read-only ECCIE ECC correction interrupt enable 24 1 read-write ECCC ECC correction 30 1 read-write ECCD ECC detection 31 1 read-write OPTR OPTR Flash option register 0x20 0x20 read-write 0xF0000000 RDP Read protection level 0 8 BOR_LEV BOR reset Level 8 3 nRST_STOP nRST_STOP 12 1 nRST_STDBY nRST_STDBY 13 1 nRST_SHDW nRST_SHDW 14 1 IDWG_SW Independent watchdog selection 16 1 IWDG_STOP Independent watchdog counter freeze in Stop mode 17 1 IWDG_STDBY Independent watchdog counter freeze in Standby mode 18 1 WWDG_SW Window watchdog selection 19 1 BFB2 Dual-bank boot 20 1 DUALBANK Dual-Bank on 512 KB or 256 KB Flash memory devices 21 1 nBOOT1 Boot configuration 23 1 SRAM2_PE SRAM2 parity check enable 24 1 SRAM2_RST SRAM2 Erase when system reset 25 1 nSWBOOT0 Software BOOT0 26 1 nBOOT0 nBOOT0 option bit 27 1 PCROP1SR PCROP1SR Flash Bank 1 PCROP Start address register 0x24 0x20 read-write 0xFFFF0000 PCROP1_STRT Bank 1 PCROP area start offset 0 16 PCROP1ER PCROP1ER Flash Bank 1 PCROP End address register 0x28 0x20 read-write 0x0FFF0000 PCROP1_END Bank 1 PCROP area end offset 0 16 PCROP_RDP PCROP area preserved when RDP level decreased 31 1 WRP1AR WRP1AR Flash Bank 1 WRP area A address register 0x2C 0x20 read-write 0xFF00FF00 WRP1A_STRT Bank 1 WRP first area start offset 0 8 WRP1A_END Bank 1 WRP first area A end offset 16 8 WRP1BR WRP1BR Flash Bank 1 WRP area B address register 0x30 0x20 read-write 0xFF00FF00 WRP1B_END Bank 1 WRP second area B end offset 16 8 WRP1B_STRT Bank 1 WRP second area B start offset 0 8 PCROP2SR PCROP2SR Flash Bank 2 PCROP Start address register 0x44 0x20 read-write 0xFFFF0000 PCROP2_STRT Bank 2 PCROP area start offset 0 16 PCROP2ER PCROP2ER Flash Bank 2 PCROP End address register 0x48 0x20 read-write 0xFFFF0000 PCROP2_END Bank 2 PCROP area end offset 0 16 WRP2AR WRP2AR Flash Bank 2 WRP area A address register 0x4C 0x20 read-write 0xFF00FF00 WRP2A_STRT Bank 2 WRP first area A start offset 0 8 WRP2A_END Bank 2 WRP first area A end offset 16 8 WRP2BR WRP2BR Flash Bank 2 WRP area B address register 0x50 0x20 read-write 0xFF00FF00 WRP2B_STRT Bank 2 WRP second area B start offset 0 8 WRP2B_END Bank 2 WRP second area B end offset 16 8 DBGMCU Debug support DBGMCU 0xE0042000 0x0 0x400 registers IDCODE IDCODE MCU Device ID Code Register 0x0 0x20 read-only 0x00000000 DEV_ID Device Identifier 0 16 REV_ID Revision Identifier 16 16 CR CR Debug MCU Configuration Register 0x4 0x20 read-write 0x00000000 DBG_SLEEP Debug Sleep Mode 0 1 DBG_STOP Debug Stop Mode 1 1 DBG_STANDBY Debug Standby Mode 2 1 TRACE_IOEN Trace pin assignment control 5 1 TRACE_MODE Trace pin assignment control 6 2 APB1FZR1 APB1_FZR1 APB Low Freeze Register 1 0x8 0x20 read-write 0x00000000 DBG_TIMER2_STOP Debug Timer 2 stopped when Core is halted 0 1 DBG_TIM3_STOP TIM3 counter stopped when core is halted 1 1 DBG_TIM4_STOP TIM4 counter stopped when core is halted 2 1 DBG_TIM5_STOP TIM5 counter stopped when core is halted 3 1 DBG_TIMER6_STOP Debug Timer 6 stopped when Core is halted 4 1 DBG_TIM7_STOP TIM7 counter stopped when core is halted 5 1 DBG_RTC_STOP Debug RTC stopped when Core is halted 10 1 DBG_WWDG_STOP Debug Window Wachdog stopped when Core is halted 11 1 DBG_IWDG_STOP Debug Independent Wachdog stopped when Core is halted 12 1 DBG_I2C1_STOP I2C1 SMBUS timeout mode stopped when core is halted 21 1 DBG_I2C2_STOP I2C2 SMBUS timeout mode stopped when core is halted 22 1 DBG_I2C3_STOP I2C3 SMBUS timeout counter stopped when core is halted 23 1 DBG_CAN_STOP bxCAN stopped when core is halted 25 1 DBG_LPTIMER_STOP LPTIM1 counter stopped when core is halted 31 1 APB1FZR2 APB1_FZR2 APB Low Freeze Register 2 0xC 0x20 read-write 0x00000000 DBG_LPTIM2_STOP LPTIM2 counter stopped when core is halted 5 1 APB2FZR APB2_FZR APB High Freeze Register 0x10 0x20 read-write 0x00000000 DBG_TIM1_STOP TIM1 counter stopped when core is halted 11 1 DBG_TIM8_STOP TIM8 counter stopped when core is halted 13 1 DBG_TIM15_STOP TIM15 counter stopped when core is halted 16 1 DBG_TIM16_STOP TIM16 counter stopped when core is halted 17 1 DBG_TIM17_STOP TIM17 counter stopped when core is halted 18 1 QUADSPI QuadSPI interface QUADSPI 0xA0001000 0x0 0x400 registers QUADSPI Quad SPI global interrupt 71 CR CR control register 0x0 0x20 read-write 0x00000000 PRESCALER Clock prescaler 24 8 0 255 PMM Polling match mode 23 1 PMM AndMatch AND match mode. SMF is set if all the unmasked bits received from the Flash memory match the corresponding bits in the match register. 0 OrMatch OR match mode. SMF is set if any one of the unmasked bits received from the Flash memory matches its corresponding bit in the match register. 1 APMS Automatic poll mode stop 22 1 APMS NotStopOnMatch Automatic polling mode is stopped only by abort or by disabling the QUADSPI. 0 StopOnMatch Automatic polling mode stops as soon as there is a match. 1 TEIE Transfer error interrupt enable 16 1 TEIE Disabled Interrupt disable 0 Enabled Interrupt enabled 1 TOIE TimeOut interrupt enable 20 1 SMIE Status match interrupt enable 19 1 FTIE FIFO threshold interrupt enable 18 1 TCIE Transfer complete interrupt enable 17 1 FTHRES IFO threshold level 8 5 FSEL FLASH memory selection 7 1 FSEL SelectFlash1 FLASH 1 selected 0 SelectFlash2 FLASH 2 selected 1 DFM Dual-flash mode 6 1 DFM Disabled Dual-flash mode disabled 0 Enabled Dual-flash mode enabled 1 SSHIFT Sample shift 4 1 SSHIFT NoShift No shift 0 OneHalfCycleShift 1/2 cycle shift 1 TCEN Timeout counter enable 3 1 TCEN Disabled Timeout counter is disabled, and thus the chip select (nCS) remains active indefinitely after an access in memory-mapped mode. 0 Enabled Timeout counter is enabled, and thus the chip select is released in memory-mapped mode after TIMEOUT[15:0] cycles of Flash memory inactivity. 1 DMAEN DMA enable 2 1 DMAEN Disabled DMA is disabled for indirect mode 0 Enabled DMA is enabled for indirect mode 1 ABORT Abort request 1 1 ABORT NoAbortRequested No abort requested 0 AbortRequested Abort requested 1 EN Enable 0 1 EN Disabled QUADSPI is disabled 0 Enabled QUADSPI is enabled 1 DCR DCR device configuration register 0x4 0x20 read-write 0x00000000 FSIZE FLASH memory size 16 5 0 31 CSHT Chip select high time 8 3 0 7 CKMODE Mode 0 / mode 3 0 1 CKMODE Mode0 CLK must stay low while nCS is high (chip select released). This is referred to as mode 0. 0 Mode3 CLK must stay high while nCS is high (chip select released). This is referred to as mode 3. 1 SR SR status register 0x8 0x20 read-only 0x00000000 FLEVEL FIFO level 8 7 0 31 BUSY Busy 5 1 BUSY NotBusy 0 Busy 1 TOF Timeout flag 4 1 TOF NotTimeout 0 Timeout 1 SMF Status match flag 3 1 SMF NotMatched 0 Matched 1 FTF FIFO threshold flag 2 1 FTF NotReached 0 Reached 1 TCF Transfer complete flag 1 1 TCF NotComplete 0 Complete 1 TEF Transfer error flag 0 1 TEF NoError 0 Error 1 FCR FCR flag clear register 0xC 0x20 read-write 0x00000000 CTOF Clear timeout flag 4 1 CTOF Clear clears the TOF flag in the QUADSPI_SR register 1 CSMF Clear status match flag 3 1 CSMF Clear clears the SMF flag in the QUADSPI_SR register 1 CTCF Clear transfer complete flag 1 1 CTCF Clear clears the TCF flag in the QUADSPI_SR register 1 CTEF Clear transfer error flag 0 1 CTEF Clear clears the TEF flag in the QUADSPI_SR register 1 DLR DLR data length register 0x10 0x20 read-write 0x00000000 DL Data length 0 32 0 4294967295 CCR CCR communication configuration register 0x14 0x20 read-write 0x00000000 DDRM Double data rate mode 31 1 DDRM Disabled DDR Mode disabled 0 Enabled DDR Mode enabled 1 DHHC DDR hold half cycle 30 1 DHHC NoDelay Delay the data output using analog delay 0 Delayed Delay the data output by 1/4 of a QUADSPI output clock cycle. 1 SIOO Send instruction only once mode 28 1 SIOO SendEveryTransaction Send instruction on every transaction 0 SendFirstCommand Send instruction only for the first command 1 FMODE Functional mode 26 2 FMODE IndirectWrite Indirect write mode 0 IndirectRead Indirect read mode 1 AutomaticPolling Automatic polling mode 2 MemoryMapped Memory-mapped mode 3 DMODE Data mode 24 2 DMODE NoData No data 0 SingleLine Data on a single line 1 TwoLines Data on two lines 2 FourLines Data on four lines 3 DCYC Number of dummy cycles 18 5 0 31 ABSIZE Alternate bytes size 16 2 ABSIZE Bit8 8-bit alternate byte 0 Bit16 16-bit alternate bytes 1 Bit24 24-bit alternate bytes 2 Bit32 32-bit alternate bytes 3 ABMODE Alternate bytes mode 14 2 ABMODE NoAlternateBytes No alternate bytes 0 SingleLine Alternate bytes on a single line 1 TwoLines Alternate bytes on two lines 2 FourLines Alternate bytes on four lines 3 ADSIZE Address size 12 2 ADSIZE Bit8 8-bit address 0 Bit16 16-bit address 1 Bit24 24-bit address 2 Bit32 32-bit address 3 ADMODE Address mode 10 2 ADMODE NoAddress No address 0 SingleLine Address on a single line 1 TwoLines Address on two lines 2 FourLines Address on four lines 3 IMODE Instruction mode 8 2 IMODE NoInstruction No instruction 0 SingleLine Instruction on a single line 1 TwoLines Instruction on two lines 2 FourLines Instruction on four lines 3 INSTRUCTION Instruction 0 8 0 255 AR AR address register 0x18 0x20 read-write 0x00000000 ADDRESS Address 0 32 0 4294967295 ABR ABR ABR 0x1C 0x20 read-write 0x00000000 ALTERNATE ALTERNATE 0 32 0 4294967295 DR DR Data register: full word (32 bit) access 0x20 0x20 read-write 0x00000000 DATA Data 0 32 0 4294967295 DR16 Data register: half word (16 bit) access DR 0x20 0x10 DATA Data 0 16 0 65535 DR8 Data register: one byte (8 bit) access DR 0x20 0x8 DATA Data 0 8 0 255 PSMKR PSMKR polling status mask register 0x24 0x20 read-write 0x00000000 MASK Status mask 0 32 0 4294967295 PSMAR PSMAR polling status match register 0x28 0x20 read-write 0x00000000 MATCH Status match 0 32 0 4294967295 PIR PIR polling interval register 0x2C 0x20 read-write 0x00000000 INTERVAL Polling interval 0 16 0 65535 LPTR LPTR low-power timeout register 0x30 0x20 read-write 0x00000000 TIMEOUT Timeout period 0 16 0 65535 RCC Reset and clock control RCC 0x40021000 0x0 0x400 registers RCC RCC global interrupt 5 CR CR Clock control register 0x0 0x20 0x00000063 PLLSAI2RDY SAI2 PLL clock ready flag 29 1 read-only PLLSAI2ON SAI2 PLL enable 28 1 read-write PLLSAI1RDY SAI1 PLL clock ready flag 27 1 read-only PLLSAI1ON SAI1 PLL enable 26 1 read-write PLLRDY Main PLL clock ready flag 25 1 read-only PLLON Main PLL enable 24 1 read-write CSSON Clock security system enable 19 1 write-only HSEBYP HSE crystal oscillator bypass 18 1 read-write HSERDY HSE clock ready flag 17 1 read-only HSEON HSE clock enable 16 1 read-write HSIASFS HSI automatic start from Stop 11 1 read-write HSIRDY HSI clock ready flag 10 1 read-only HSIKERON HSI always enable for peripheral kernels 9 1 read-write HSION HSI clock enable 8 1 read-write MSIRANGE MSI clock ranges 4 4 read-write MSIRANGE Range100K range 0 around 100 kHz 0 Range200K range 1 around 200 kHz 1 Range400K range 2 around 400 kHz 2 Range800K range 3 around 800 kHz 3 Range1M range 4 around 1 MHz 4 Range2M range 5 around 2 MHz 5 Range4M range 6 around 4 MHz 6 Range8M range 7 around 8 MHz 7 Range16M range 8 around 16 MHz 8 Range24M range 9 around 24 MHz 9 Range32M range 10 around 32 MHz 10 Range48M range 11 around 48 MHz 11 MSIRGSEL MSI clock range selection 3 1 write-only MSIPLLEN MSI clock PLL enable 2 1 read-write MSIRDY MSI clock ready flag 1 1 read-only MSION MSI clock enable 0 1 read-write ICSCR ICSCR Internal clock sources calibration register 0x4 0x20 0x10000000 HSITRIM HSI clock trimming 24 7 read-write HSICAL HSI clock calibration 16 8 read-only MSITRIM MSI clock trimming 8 8 read-write MSICAL MSI clock calibration 0 8 read-only CFGR CFGR Clock configuration register 0x8 0x20 0x00000000 MCOPRE Microcontroller clock output prescaler 28 3 read-only MCOSEL Microcontroller clock output 24 3 read-write STOPWUCK Wakeup from Stop and CSS backup clock selection 15 1 read-write PPRE2 APB high-speed prescaler (APB2) 11 3 read-write PPRE1 PB low-speed prescaler (APB1) 8 3 read-write HPRE AHB prescaler 4 4 read-write SWS System clock switch status 2 2 read-only SW System clock switch 0 2 read-write PLLCFGR PLLCFGR PLL configuration register 0xC 0x20 read-write 0x00001000 PLLR Main PLL division factor for PLLCLK (system clock) 25 2 PLLREN Main PLL PLLCLK output enable 24 1 PLLQ Main PLL division factor for PLLUSB1CLK(48 MHz clock) 21 2 PLLQEN Main PLL PLLUSB1CLK output enable 20 1 PLLP Main PLL division factor for PLLSAI3CLK (SAI1 and SAI2 clock) 17 1 PLLPEN Main PLL PLLSAI3CLK output enable 16 1 PLLN Main PLL multiplication factor for VCO 8 7 PLLM Division factor for the main PLL and audio PLL (PLLSAI1 and PLLSAI2) input clock 4 3 PLLSRC Main PLL, PLLSAI1 and PLLSAI2 entry clock source 0 2 PLLPDIV Main PLL division factor for PLLSAI2CLK 27 5 PLLSAI1CFGR PLLSAI1CFGR PLLSAI1 configuration register 0x10 0x20 read-write 0x00001000 PLLSAI1R PLLSAI1 division factor for PLLADC1CLK (ADC clock) 25 2 PLLSAI1REN PLLSAI1 PLLADC1CLK output enable 24 1 PLLSAI1Q SAI1PLL division factor for PLLUSB2CLK (48 MHz clock) 21 2 PLLSAI1QEN SAI1PLL PLLUSB2CLK output enable 20 1 PLLSAI1P SAI1PLL division factor for PLLSAI1CLK (SAI1 or SAI2 clock) 17 1 PLLSAI1PEN SAI1PLL PLLSAI1CLK output enable 16 1 PLLSAI1N SAI1PLL multiplication factor for VCO 8 7 PLLSAI1PDIV PLLSAI1 division factor for PLLSAI1CLK 27 5 PLLSAI2CFGR PLLSAI2CFGR PLLSAI2 configuration register 0x14 0x20 read-write 0x00001000 PLLSAI2R PLLSAI2 division factor for PLLADC2CLK (ADC clock) 25 2 PLLSAI2REN PLLSAI2 PLLADC2CLK output enable 24 1 PLLSAI2P SAI1PLL division factor for PLLSAI2CLK (SAI1 or SAI2 clock) 17 1 PLLSAI2PEN SAI2PLL PLLSAI2CLK output enable 16 1 PLLSAI2N SAI2PLL multiplication factor for VCO 8 7 PLLSAI2PDIV PLLSAI2 division factor for PLLSAI2CLK 27 5 CIER CIER Clock interrupt enable register 0x18 0x20 read-write 0x00000000 LSECSSIE LSE clock security system interrupt enable 9 1 PLLSAI2RDYIE PLLSAI2 ready interrupt enable 7 1 PLLSAI1RDYIE PLLSAI1 ready interrupt enable 6 1 PLLRDYIE PLL ready interrupt enable 5 1 HSERDYIE HSE ready interrupt enable 4 1 HSIRDYIE HSI ready interrupt enable 3 1 MSIRDYIE MSI ready interrupt enable 2 1 LSERDYIE LSE ready interrupt enable 1 1 LSIRDYIE LSI ready interrupt enable 0 1 HSI48RDYIE HSI48 ready interrupt enable 10 1 CIFR CIFR Clock interrupt flag register 0x1C 0x20 read-only 0x00000000 LSECSSF LSE Clock security system interrupt flag 9 1 CSSF Clock security system interrupt flag 8 1 PLLSAI2RDYF PLLSAI2 ready interrupt flag 7 1 PLLSAI1RDYF PLLSAI1 ready interrupt flag 6 1 PLLRDYF PLL ready interrupt flag 5 1 HSERDYF HSE ready interrupt flag 4 1 HSIRDYF HSI ready interrupt flag 3 1 MSIRDYF MSI ready interrupt flag 2 1 LSERDYF LSE ready interrupt flag 1 1 LSIRDYF LSI ready interrupt flag 0 1 HSI48RDYF HSI48 ready interrupt flag 10 1 CICR CICR Clock interrupt clear register 0x20 0x20 write-only 0x00000000 LSECSSC LSE Clock security system interrupt clear 9 1 CSSC Clock security system interrupt clear 8 1 PLLSAI2RDYC PLLSAI2 ready interrupt clear 7 1 PLLSAI1RDYC PLLSAI1 ready interrupt clear 6 1 PLLRDYC PLL ready interrupt clear 5 1 HSERDYC HSE ready interrupt clear 4 1 HSIRDYC HSI ready interrupt clear 3 1 MSIRDYC MSI ready interrupt clear 2 1 LSERDYC LSE ready interrupt clear 1 1 LSIRDYC LSI ready interrupt clear 0 1 HSI48RDYC HSI48 oscillator ready interrupt clear 10 1 AHB1RSTR AHB1RSTR AHB1 peripheral reset register 0x28 0x20 read-write 0x00000000 TSCRST Touch Sensing Controller reset 16 1 CRCRST CRC reset 12 1 FLASHRST Flash memory interface reset 8 1 DMA2RST DMA2 reset 1 1 DMA1RST DMA1 reset 0 1 DMA2DRST DMA2D reset 17 1 AHB2RSTR AHB2RSTR AHB2 peripheral reset register 0x2C 0x20 read-write 0x00000000 RNGRST Random number generator reset 18 1 AESRST AES hardware accelerator reset 16 1 ADCRST ADC reset 13 1 OTGFSRST USB OTG FS reset 12 1 GPIOHRST IO port H reset 7 1 GPIOGRST IO port G reset 6 1 GPIOFRST IO port F reset 5 1 GPIOERST IO port E reset 4 1 GPIODRST IO port D reset 3 1 GPIOCRST IO port C reset 2 1 GPIOBRST IO port B reset 1 1 GPIOARST IO port A reset 0 1 GPIOIRST IO port I reset 8 1 DCMIRST Digital Camera Interface reset 14 1 HASH1RST Hash reset 17 1 AHB3RSTR AHB3RSTR AHB3 peripheral reset register 0x30 0x20 read-write 0x00000000 QSPIRST Quad SPI memory interface reset 8 1 FMCRST Flexible memory controller reset 0 1 APB1RSTR1 APB1RSTR1 APB1 peripheral reset register 1 0x38 0x20 read-write 0x00000000 LPTIM1RST Low Power Timer 1 reset 31 1 OPAMPRST OPAMP interface reset 30 1 DAC1RST DAC1 interface reset 29 1 PWRRST Power interface reset 28 1 CAN1RST CAN1 reset 25 1 I2C3RST I2C3 reset 23 1 I2C2RST I2C2 reset 22 1 I2C1RST I2C1 reset 21 1 UART5RST UART5 reset 20 1 UART4RST UART4 reset 19 1 USART3RST USART3 reset 18 1 USART2RST USART2 reset 17 1 SPI3RST SPI3 reset 15 1 SPI2RST SPI2 reset 14 1 LCDRST LCD interface reset 9 1 TIM7RST TIM7 timer reset 5 1 TIM6RST TIM6 timer reset 4 1 TIM5RST TIM5 timer reset 3 1 TIM4RST TIM3 timer reset 2 1 TIM3RST TIM3 timer reset 1 1 TIM2RST TIM2 timer reset 0 1 CRSRST CRS reset 24 1 CAN2RST CAN2 reset 26 1 APB1RSTR2 APB1RSTR2 APB1 peripheral reset register 2 0x3C 0x20 read-write 0x00000000 LPTIM2RST Low-power timer 2 reset 5 1 SWPMI1RST Single wire protocol reset 2 1 LPUART1RST Low-power UART 1 reset 0 1 I2C4RST I2C4 reset 1 1 APB2RSTR APB2RSTR APB2 peripheral reset register 0x40 0x20 read-write 0x00000000 DFSDMRST Digital filters for sigma-delata modulators (DFSDM) reset 24 1 SAI2RST Serial audio interface 2 (SAI2) reset 22 1 SAI1RST Serial audio interface 1 (SAI1) reset 21 1 TIM17RST TIM17 timer reset 18 1 TIM16RST TIM16 timer reset 17 1 TIM15RST TIM15 timer reset 16 1 USART1RST USART1 reset 14 1 TIM8RST TIM8 timer reset 13 1 SPI1RST SPI1 reset 12 1 TIM1RST TIM1 timer reset 11 1 SDMMCRST SDMMC reset 10 1 SYSCFGRST System configuration (SYSCFG) reset 0 1 AHB1ENR AHB1ENR AHB1 peripheral clock enable register 0x48 0x20 read-write 0x00000100 TSCEN Touch Sensing Controller clock enable 16 1 CRCEN CRC clock enable 12 1 FLASHEN Flash memory interface clock enable 8 1 DMA2EN DMA2 clock enable 1 1 DMA1EN DMA1 clock enable 0 1 DMA2DEN DMA2D clock enable 17 1 AHB2ENR AHB2ENR AHB2 peripheral clock enable register 0x4C 0x20 read-write 0x00000000 RNGEN Random Number Generator clock enable 18 1 AESEN AES accelerator clock enable 16 1 ADCEN ADC clock enable 13 1 ADCEN Disabled ADC clock disabled 0 Enabled ADC clock enabled 1 OTGFSEN OTG full speed clock enable 12 1 GPIOHEN IO port H clock enable 7 1 GPIOGEN IO port G clock enable 6 1 GPIOFEN IO port F clock enable 5 1 GPIOEEN IO port E clock enable 4 1 GPIODEN IO port D clock enable 3 1 GPIOCEN IO port C clock enable 2 1 GPIOBEN IO port B clock enable 1 1 GPIOAEN IO port A clock enable 0 1 GPIOIEN IO port I clock enable 8 1 DCMIEN DCMI clock enable 14 1 HASH1EN HASH clock enable 17 1 AHB3ENR AHB3ENR AHB3 peripheral clock enable register 0x50 0x20 read-write 0x00000000 QSPIEN QSPIEN 8 1 FMCEN Flexible memory controller clock enable 0 1 APB1ENR1 APB1ENR1 APB1ENR1 0x58 0x20 read-write 0x00000000 LPTIM1EN Low power timer 1 clock enable 31 1 LPTIM1EN Disabled LPTIM1 clock disabled 0 Enabled LPTIM1 clock enabled 1 OPAMPEN OPAMP interface clock enable 30 1 DAC1EN DAC1 interface clock enable 29 1 PWREN Power interface clock enable 28 1 CAN1EN CAN1 clock enable 25 1 I2C3EN I2C3 clock enable 23 1 I2C3EN Disabled I2C3 clock disabled 0 Enabled I2C3 clock enabled 1 I2C2EN I2C2 clock enable 22 1 I2C2EN Disabled I2C2 clock disabled 0 Enabled I2C2 clock enabled 1 I2C1EN I2C1 clock enable 21 1 I2C1EN Disabled I2C1 clock disabled 0 Enabled I2C1 clock enabled 1 UART5EN UART5 clock enable 20 1 UART5EN Disabled UART5 clock disabled 0 Enabled UART5 clock enabled 1 UART4EN UART4 clock enable 19 1 UART4EN Disabled UART4 clock disabled 0 Enabled UART4 clock enabled 1 USART3EN USART3 clock enable 18 1 USART3EN Disabled USART3 clock disabled 0 Enabled USART3 clock enabled 1 USART2EN USART2 clock enable 17 1 USART2EN Disabled USART2 clock disabled 0 Enabled USART2 clock enabled 1 SPI3EN SPI peripheral 3 clock enable 15 1 SPI2EN SPI2 clock enable 14 1 WWDGEN Window watchdog clock enable 11 1 LCDEN LCD clock enable 9 1 TIM7EN TIM7 timer clock enable 5 1 TIM6EN TIM6 timer clock enable 4 1 TIM5EN TIM5 timer clock enable 3 1 TIM4EN TIM4 timer clock enable 2 1 TIM3EN TIM3 timer clock enable 1 1 TIM2EN TIM2 timer clock enable 0 1 RTCAPBEN RTC APB clock enable 10 1 CRSEN Clock Recovery System clock enable 24 1 CAN2EN CAN2 clock enable 26 1 APB1ENR2 APB1ENR2 APB1 peripheral clock enable register 2 0x5C 0x20 read-write 0x00000000 LPTIM2EN LPTIM2EN 5 1 LPTIM2EN Disabled LPTIM2 clock disabled 0 Enabled LPTIM2 clock enabled 1 SWPMI1EN Single wire protocol clock enable 2 1 LPUART1EN Low power UART 1 clock enable 0 1 LPUART1EN Disabled LPUART1 clock disabled 0 Enabled LPUART1 clock enabled 1 I2C4EN I2C4 clock enable 1 1 APB2ENR APB2ENR APB2ENR 0x60 0x20 read-write 0x00000000 DFSDMEN DFSDM timer clock enable 24 1 SAI2EN SAI2 clock enable 22 1 SAI1EN SAI1 clock enable 21 1 TIM17EN TIM17 timer clock enable 18 1 TIM16EN TIM16 timer clock enable 17 1 TIM15EN TIM15 timer clock enable 16 1 USART1EN USART1clock enable 14 1 USART1EN Disabled USART1 clock disabled 0 Enabled USART1 clock enabled 1 TIM8EN TIM8 timer clock enable 13 1 SPI1EN SPI1 clock enable 12 1 TIM1EN TIM1 timer clock enable 11 1 SDMMCEN SDMMC clock enable 10 1 FIREWALLEN Firewall clock enable 7 1 SYSCFGEN SYSCFG clock enable 0 1 AHB1SMENR AHB1SMENR AHB1 peripheral clocks enable in Sleep and Stop modes register 0x68 0x20 read-write 0x00011303 TSCSMEN Touch Sensing Controller clocks enable during Sleep and Stop modes 16 1 CRCSMEN CRCSMEN 12 1 SRAM1SMEN SRAM1 interface clocks enable during Sleep and Stop modes 9 1 FLASHSMEN Flash memory interface clocks enable during Sleep and Stop modes 8 1 DMA2SMEN DMA2 clocks enable during Sleep and Stop modes 1 1 DMA1SMEN DMA1 clocks enable during Sleep and Stop modes 0 1 DMA2DSMEN DMA2D clock enable during Sleep and Stop modes 17 1 AHB2SMENR AHB2SMENR AHB2 peripheral clocks enable in Sleep and Stop modes register 0x6C 0x20 read-write 0x000532FF RNGSMEN Random Number Generator clocks enable during Sleep and Stop modes 18 1 AESSMEN AES accelerator clocks enable during Sleep and Stop modes 16 1 ADCFSSMEN ADC clocks enable during Sleep and Stop modes 13 1 OTGFSSMEN OTG full speed clocks enable during Sleep and Stop modes 12 1 SRAM2SMEN SRAM2 interface clocks enable during Sleep and Stop modes 9 1 GPIOHSMEN IO port H clocks enable during Sleep and Stop modes 7 1 GPIOGSMEN IO port G clocks enable during Sleep and Stop modes 6 1 GPIOFSMEN IO port F clocks enable during Sleep and Stop modes 5 1 GPIOESMEN IO port E clocks enable during Sleep and Stop modes 4 1 GPIODSMEN IO port D clocks enable during Sleep and Stop modes 3 1 GPIOCSMEN IO port C clocks enable during Sleep and Stop modes 2 1 GPIOBSMEN IO port B clocks enable during Sleep and Stop modes 1 1 GPIOASMEN IO port A clocks enable during Sleep and Stop modes 0 1 GPIOISMEN IO port I clocks enable during Sleep and Stop modes 8 1 DCMISMEN DCMI clock enable during Sleep and Stop modes 14 1 HASH1SMEN HASH clock enable during Sleep and Stop modes 17 1 AHB3SMENR AHB3SMENR AHB3 peripheral clocks enable in Sleep and Stop modes register 0x70 0x20 read-write 0x00000101 QSPISMEN QSPISMEN 8 1 FMCSMEN Flexible memory controller clocks enable during Sleep and Stop modes 0 1 APB1SMENR1 APB1SMENR1 APB1SMENR1 0x78 0x20 read-write 0xF2FECA3F LPTIM1SMEN Low power timer 1 clocks enable during Sleep and Stop modes 31 1 OPAMPSMEN OPAMP interface clocks enable during Sleep and Stop modes 30 1 DAC1SMEN DAC1 interface clocks enable during Sleep and Stop modes 29 1 PWRSMEN Power interface clocks enable during Sleep and Stop modes 28 1 CAN1SMEN CAN1 clocks enable during Sleep and Stop modes 25 1 I2C3SMEN I2C3 clocks enable during Sleep and Stop modes 23 1 I2C2SMEN I2C2 clocks enable during Sleep and Stop modes 22 1 I2C1SMEN I2C1 clocks enable during Sleep and Stop modes 21 1 UART5SMEN UART5 clocks enable during Sleep and Stop modes 20 1 UART4SMEN UART4 clocks enable during Sleep and Stop modes 19 1 USART3SMEN USART3 clocks enable during Sleep and Stop modes 18 1 USART2SMEN USART2 clocks enable during Sleep and Stop modes 17 1 SP3SMEN SPI3 clocks enable during Sleep and Stop modes 15 1 SPI2SMEN SPI2 clocks enable during Sleep and Stop modes 14 1 WWDGSMEN Window watchdog clocks enable during Sleep and Stop modes 11 1 LCDSMEN LCD clocks enable during Sleep and Stop modes 9 1 TIM7SMEN TIM7 timer clocks enable during Sleep and Stop modes 5 1 TIM6SMEN TIM6 timer clocks enable during Sleep and Stop modes 4 1 TIM5SMEN TIM5 timer clocks enable during Sleep and Stop modes 3 1 TIM4SMEN TIM4 timer clocks enable during Sleep and Stop modes 2 1 TIM3SMEN TIM3 timer clocks enable during Sleep and Stop modes 1 1 TIM2SMEN TIM2 timer clocks enable during Sleep and Stop modes 0 1 RTCAPBSMEN RTC APB clock enable during Sleep and Stop modes 10 1 CAN2SMEN CAN2 clocks enable during Sleep and Stop modes 26 1 APB1SMENR2 APB1SMENR2 APB1 peripheral clocks enable in Sleep and Stop modes register 2 0x7C 0x20 read-write 0x00000025 LPTIM2SMEN LPTIM2SMEN 5 1 SWPMI1SMEN Single wire protocol clocks enable during Sleep and Stop modes 2 1 LPUART1SMEN Low power UART 1 clocks enable during Sleep and Stop modes 0 1 I2C4SMEN I2C4 clocks enable during Sleep and Stop modes 1 1 APB2SMENR APB2SMENR APB2SMENR 0x80 0x20 read-write 0x01677C01 DFSDMSMEN DFSDM timer clocks enable during Sleep and Stop modes 24 1 SAI2SMEN SAI2 clocks enable during Sleep and Stop modes 22 1 SAI1SMEN SAI1 clocks enable during Sleep and Stop modes 21 1 TIM17SMEN TIM17 timer clocks enable during Sleep and Stop modes 18 1 TIM16SMEN TIM16 timer clocks enable during Sleep and Stop modes 17 1 TIM15SMEN TIM15 timer clocks enable during Sleep and Stop modes 16 1 USART1SMEN USART1clocks enable during Sleep and Stop modes 14 1 TIM8SMEN TIM8 timer clocks enable during Sleep and Stop modes 13 1 SPI1SMEN SPI1 clocks enable during Sleep and Stop modes 12 1 TIM1SMEN TIM1 timer clocks enable during Sleep and Stop modes 11 1 SDMMCSMEN SDMMC clocks enable during Sleep and Stop modes 10 1 SYSCFGSMEN SYSCFG clocks enable during Sleep and Stop modes 0 1 CCIPR CCIPR CCIPR 0x88 0x20 read-write 0x00000000 DFSDMSEL DFSDM clock source selection 31 1 SWPMI1SEL SWPMI1 clock source selection 30 1 ADCSEL ADCs clock source selection 28 2 ADCSEL NoClock No clock selected 0 PLLSAI1 PLLSAI1 clock selected 1 PLLSAI2 PLLSAI2 clock selected (only for STM32L47x/L48x/L49x/L4Ax devices) 2 SYSCLK SYSCLK clock selected 3 CLK48SEL 48 MHz clock source selection 26 2 CLK48SEL HSI48 HSI48 clock selected (only for STM32L41x/L42x/L43x/L44x/L45x/L46x/L49x/L4Ax devices, otherwise no clock selected) 0 PLLSAI1 PLLSAI1 clock selected 1 PLL PLL clock selected 2 MSI MSI clock selected 3 SAI2SEL SAI2 clock source selection 24 2 SAI1SEL SAI1 clock source selection 22 2 LPTIM1SEL Low power timer 1 clock source selection 18 2 LPTIM1SEL PCLK PCLK clock selected 0 LSI LSI clock selected 1 HSI16 HSI16 clock selected 2 LSE LSE clock selected 3 LPTIM2SEL Low power timer 2 clock source selection 20 2 I2C1SEL I2C1 clock source selection 12 2 I2C1SEL PCLK PCLK clock selected 0 SYSCLK SYSCLK clock selected 1 HSI16 HSI16 clock selected 2 I2C3SEL I2C3 clock source selection 16 2 I2C2SEL I2C2 clock source selection 14 2 LPUART1SEL LPUART1 clock source selection 10 2 LPUART1SEL PCLK PCLK clock selected 0 SYSCLK SYSCLK clock selected 1 HSI16 HSI16 clock selected 2 LSE LSE clock selected 3 UART5SEL UART5 clock source selection 8 2 UART4SEL UART4 clock source selection 6 2 USART1SEL USART1 clock source selection 0 2 USART1SEL PCLK PCLK clock selected 0 SYSCLK SYSCLK clock selected 1 HSI16 HSI16 clock selected 2 LSE LSE clock selected 3 USART3SEL USART3 clock source selection 4 2 USART2SEL USART2 clock source selection 2 2 BDCR BDCR BDCR 0x90 0x20 0x00000000 LSCOSEL Low speed clock output selection 25 1 read-write LSCOEN Low speed clock output enable 24 1 read-write BDRST Backup domain software reset 16 1 read-write RTCEN RTC clock enable 15 1 read-write RTCEN Disabled RTC clock disabled 0 Enabled RTC clock enabled 1 RTCSEL RTC clock source selection 8 2 read-write RTCSEL NoClock No clock 0 LSE LSE oscillator clock selected 1 LSI LSI oscillator clock selected 2 HSE HSE oscillator clock divided by 32 selected 3 LSECSSD LSECSSD 6 1 read-only LSECSSON LSECSSON 5 1 read-write LSEDRV SE oscillator drive capability 3 2 read-write LSEBYP LSE oscillator bypass 2 1 read-write LSERDY LSE oscillator ready 1 1 read-only LSEON LSE oscillator enable 0 1 read-write CSR CSR CSR 0x94 0x20 0x0C000600 LPWRSTF Low-power reset flag 31 1 read-only WWDGRSTF Window watchdog reset flag 30 1 read-only IWDGRSTF Independent window watchdog reset flag 29 1 read-only SFTRSTF Software reset flag 28 1 read-only BORRSTF BOR flag 27 1 read-only PINRSTF Pin reset flag 26 1 read-only OBLRSTF Option byte loader reset flag 25 1 read-only FIREWALLRSTF Firewall reset flag 24 1 read-only RMVF Remove reset flag 23 1 read-write MSISRANGE SI range after Standby mode 8 4 read-write LSIRDY LSI oscillator ready 1 1 read-only LSION LSI oscillator enable 0 1 read-write CRRCR Clock recovery RC register 0x98 HSI48CAL These bits are initialized at startup with the factory-programmed HSI48 calibration trim value. 7 9 read-only HSI48RDY Set by hardware to indicate that HSI48 oscillator is stable. This bit is set only when HSI48 is enabled by software by setting HSI48ON. 1 1 read-only HSI48ON Set and cleared by software. Cleared by hardware to stop the HSI48 when entering in Stop, Standby or Shutdown modes. 0 1 read-write PWR Power control PWR 0x40007000 0x0 0x400 registers CR1 CR1 Power control register 1 0x0 0x20 read-write 0x00000200 LPR Low-power run 14 1 VOS Voltage scaling range selection 9 2 DBP Disable backup domain write protection 8 1 LPMS Low-power mode selection 0 3 CR2 CR2 Power control register 2 0x4 0x20 read-write 0x00000000 USV VDDUSB USB supply valid 10 1 IOSV VDDIO2 Independent I/Os supply valid 9 1 PVME4 Peripheral voltage monitoring 4 enable: VDDA vs. 2.2V 7 1 PVME3 Peripheral voltage monitoring 3 enable: VDDA vs. 1.62V 6 1 PVME2 Peripheral voltage monitoring 2 enable: VDDIO2 vs. 0.9V 5 1 PVME1 Peripheral voltage monitoring 1 enable: VDDUSB vs. 1.2V 4 1 PLS Power voltage detector level selection 1 3 PVDE Power voltage detector enable 0 1 CR3 CR3 Power control register 3 0x8 0x20 read-write 0x00008000 EWF Enable internal wakeup line 15 1 APC Apply pull-up and pull-down configuration 10 1 RRS SRAM2 retention in Standby mode 8 1 EWUP5 Enable Wakeup pin WKUP5 4 1 EWUP4 Enable Wakeup pin WKUP4 3 1 EWUP3 Enable Wakeup pin WKUP3 2 1 EWUP2 Enable Wakeup pin WKUP2 1 1 EWUP1 Enable Wakeup pin WKUP1 0 1 CR4 CR4 Power control register 4 0xC 0x20 read-write 0x00000000 VBRS VBAT battery charging resistor selection 9 1 VBE VBAT battery charging enable 8 1 WP5 Wakeup pin WKUP5 polarity 4 1 WP4 Wakeup pin WKUP4 polarity 3 1 WP3 Wakeup pin WKUP3 polarity 2 1 WP2 Wakeup pin WKUP2 polarity 1 1 WP1 Wakeup pin WKUP1 polarity 0 1 SR1 SR1 Power status register 1 0x10 0x20 read-only 0x00000000 WUFI Wakeup flag internal 15 1 CSBF Standby flag 8 1 CWUF5 Wakeup flag 5 4 1 CWUF4 Wakeup flag 4 3 1 CWUF3 Wakeup flag 3 2 1 CWUF2 Wakeup flag 2 1 1 CWUF1 Wakeup flag 1 0 1 SR2 SR2 Power status register 2 0x14 0x20 read-only 0x00000000 PVMO4 Peripheral voltage monitoring output: VDDA vs. 2.2 V 15 1 PVMO3 Peripheral voltage monitoring output: VDDA vs. 1.62 V 14 1 PVMO2 Peripheral voltage monitoring output: VDDIO2 vs. 0.9 V 13 1 PVMO1 Peripheral voltage monitoring output: VDDUSB vs. 1.2 V 12 1 PVDO Power voltage detector output 11 1 VOSF Voltage scaling flag 10 1 REGLPF Low-power regulator flag 9 1 REGLPS Low-power regulator started 8 1 SCR SCR Power status clear register 0x18 0x20 write-only 0x00000000 SBF Clear standby flag 8 1 WUF5 Clear wakeup flag 5 4 1 WUF4 Clear wakeup flag 4 3 1 WUF3 Clear wakeup flag 3 2 1 WUF2 Clear wakeup flag 2 1 1 WUF1 Clear wakeup flag 1 0 1 PUCRA PUCRA Power Port A pull-up control register 0x20 0x20 read-write 0x00000000 PU15 Port A pull-up bit y (y=0..15) 15 1 PU14 Port A pull-up bit y (y=0..15) 14 1 PU13 Port A pull-up bit y (y=0..15) 13 1 PU12 Port A pull-up bit y (y=0..15) 12 1 PU11 Port A pull-up bit y (y=0..15) 11 1 PU10 Port A pull-up bit y (y=0..15) 10 1 PU9 Port A pull-up bit y (y=0..15) 9 1 PU8 Port A pull-up bit y (y=0..15) 8 1 PU7 Port A pull-up bit y (y=0..15) 7 1 PU6 Port A pull-up bit y (y=0..15) 6 1 PU5 Port A pull-up bit y (y=0..15) 5 1 PU4 Port A pull-up bit y (y=0..15) 4 1 PU3 Port A pull-up bit y (y=0..15) 3 1 PU2 Port A pull-up bit y (y=0..15) 2 1 PU1 Port A pull-up bit y (y=0..15) 1 1 PU0 Port A pull-up bit y (y=0..15) 0 1 PDCRA PDCRA Power Port A pull-down control register 0x24 0x20 read-write 0x00000000 PD15 Port A pull-down bit y (y=0..15) 15 1 PD14 Port A pull-down bit y (y=0..15) 14 1 PD13 Port A pull-down bit y (y=0..15) 13 1 PD12 Port A pull-down bit y (y=0..15) 12 1 PD11 Port A pull-down bit y (y=0..15) 11 1 PD10 Port A pull-down bit y (y=0..15) 10 1 PD9 Port A pull-down bit y (y=0..15) 9 1 PD8 Port A pull-down bit y (y=0..15) 8 1 PD7 Port A pull-down bit y (y=0..15) 7 1 PD6 Port A pull-down bit y (y=0..15) 6 1 PD5 Port A pull-down bit y (y=0..15) 5 1 PD4 Port A pull-down bit y (y=0..15) 4 1 PD3 Port A pull-down bit y (y=0..15) 3 1 PD2 Port A pull-down bit y (y=0..15) 2 1 PD1 Port A pull-down bit y (y=0..15) 1 1 PD0 Port A pull-down bit y (y=0..15) 0 1 PUCRB PUCRB Power Port B pull-up control register 0x28 0x20 read-write 0x00000000 PU15 Port B pull-up bit y (y=0..15) 15 1 PU14 Port B pull-up bit y (y=0..15) 14 1 PU13 Port B pull-up bit y (y=0..15) 13 1 PU12 Port B pull-up bit y (y=0..15) 12 1 PU11 Port B pull-up bit y (y=0..15) 11 1 PU10 Port B pull-up bit y (y=0..15) 10 1 PU9 Port B pull-up bit y (y=0..15) 9 1 PU8 Port B pull-up bit y (y=0..15) 8 1 PU7 Port B pull-up bit y (y=0..15) 7 1 PU6 Port B pull-up bit y (y=0..15) 6 1 PU5 Port B pull-up bit y (y=0..15) 5 1 PU4 Port B pull-up bit y (y=0..15) 4 1 PU3 Port B pull-up bit y (y=0..15) 3 1 PU2 Port B pull-up bit y (y=0..15) 2 1 PU1 Port B pull-up bit y (y=0..15) 1 1 PU0 Port B pull-up bit y (y=0..15) 0 1 PDCRB PDCRB Power Port B pull-down control register 0x2C 0x20 read-write 0x00000000 PD15 Port B pull-down bit y (y=0..15) 15 1 PD14 Port B pull-down bit y (y=0..15) 14 1 PD13 Port B pull-down bit y (y=0..15) 13 1 PD12 Port B pull-down bit y (y=0..15) 12 1 PD11 Port B pull-down bit y (y=0..15) 11 1 PD10 Port B pull-down bit y (y=0..15) 10 1 PD9 Port B pull-down bit y (y=0..15) 9 1 PD8 Port B pull-down bit y (y=0..15) 8 1 PD7 Port B pull-down bit y (y=0..15) 7 1 PD6 Port B pull-down bit y (y=0..15) 6 1 PD5 Port B pull-down bit y (y=0..15) 5 1 PD4 Port B pull-down bit y (y=0..15) 4 1 PD3 Port B pull-down bit y (y=0..15) 3 1 PD2 Port B pull-down bit y (y=0..15) 2 1 PD1 Port B pull-down bit y (y=0..15) 1 1 PD0 Port B pull-down bit y (y=0..15) 0 1 PUCRC PUCRC Power Port C pull-up control register 0x30 0x20 read-write 0x00000000 PU15 Port C pull-up bit y (y=0..15) 15 1 PU14 Port C pull-up bit y (y=0..15) 14 1 PU13 Port C pull-up bit y (y=0..15) 13 1 PU12 Port C pull-up bit y (y=0..15) 12 1 PU11 Port C pull-up bit y (y=0..15) 11 1 PU10 Port C pull-up bit y (y=0..15) 10 1 PU9 Port C pull-up bit y (y=0..15) 9 1 PU8 Port C pull-up bit y (y=0..15) 8 1 PU7 Port C pull-up bit y (y=0..15) 7 1 PU6 Port C pull-up bit y (y=0..15) 6 1 PU5 Port C pull-up bit y (y=0..15) 5 1 PU4 Port C pull-up bit y (y=0..15) 4 1 PU3 Port C pull-up bit y (y=0..15) 3 1 PU2 Port C pull-up bit y (y=0..15) 2 1 PU1 Port C pull-up bit y (y=0..15) 1 1 PU0 Port C pull-up bit y (y=0..15) 0 1 PDCRC PDCRC Power Port C pull-down control register 0x34 0x20 read-write 0x00000000 PD15 Port C pull-down bit y (y=0..15) 15 1 PD14 Port C pull-down bit y (y=0..15) 14 1 PD13 Port C pull-down bit y (y=0..15) 13 1 PD12 Port C pull-down bit y (y=0..15) 12 1 PD11 Port C pull-down bit y (y=0..15) 11 1 PD10 Port C pull-down bit y (y=0..15) 10 1 PD9 Port C pull-down bit y (y=0..15) 9 1 PD8 Port C pull-down bit y (y=0..15) 8 1 PD7 Port C pull-down bit y (y=0..15) 7 1 PD6 Port C pull-down bit y (y=0..15) 6 1 PD5 Port C pull-down bit y (y=0..15) 5 1 PD4 Port C pull-down bit y (y=0..15) 4 1 PD3 Port C pull-down bit y (y=0..15) 3 1 PD2 Port C pull-down bit y (y=0..15) 2 1 PD1 Port C pull-down bit y (y=0..15) 1 1 PD0 Port C pull-down bit y (y=0..15) 0 1 PUCRD PUCRD Power Port D pull-up control register 0x38 0x20 read-write 0x00000000 PU15 Port D pull-up bit y (y=0..15) 15 1 PU14 Port D pull-up bit y (y=0..15) 14 1 PU13 Port D pull-up bit y (y=0..15) 13 1 PU12 Port D pull-up bit y (y=0..15) 12 1 PU11 Port D pull-up bit y (y=0..15) 11 1 PU10 Port D pull-up bit y (y=0..15) 10 1 PU9 Port D pull-up bit y (y=0..15) 9 1 PU8 Port D pull-up bit y (y=0..15) 8 1 PU7 Port D pull-up bit y (y=0..15) 7 1 PU6 Port D pull-up bit y (y=0..15) 6 1 PU5 Port D pull-up bit y (y=0..15) 5 1 PU4 Port D pull-up bit y (y=0..15) 4 1 PU3 Port D pull-up bit y (y=0..15) 3 1 PU2 Port D pull-up bit y (y=0..15) 2 1 PU1 Port D pull-up bit y (y=0..15) 1 1 PU0 Port D pull-up bit y (y=0..15) 0 1 PDCRD PDCRD Power Port D pull-down control register 0x3C 0x20 read-write 0x00000000 PD15 Port D pull-down bit y (y=0..15) 15 1 PD14 Port D pull-down bit y (y=0..15) 14 1 PD13 Port D pull-down bit y (y=0..15) 13 1 PD12 Port D pull-down bit y (y=0..15) 12 1 PD11 Port D pull-down bit y (y=0..15) 11 1 PD10 Port D pull-down bit y (y=0..15) 10 1 PD9 Port D pull-down bit y (y=0..15) 9 1 PD8 Port D pull-down bit y (y=0..15) 8 1 PD7 Port D pull-down bit y (y=0..15) 7 1 PD6 Port D pull-down bit y (y=0..15) 6 1 PD5 Port D pull-down bit y (y=0..15) 5 1 PD4 Port D pull-down bit y (y=0..15) 4 1 PD3 Port D pull-down bit y (y=0..15) 3 1 PD2 Port D pull-down bit y (y=0..15) 2 1 PD1 Port D pull-down bit y (y=0..15) 1 1 PD0 Port D pull-down bit y (y=0..15) 0 1 PUCRE PUCRE Power Port E pull-up control register 0x40 0x20 read-write 0x00000000 PU15 Port E pull-up bit y (y=0..15) 15 1 PU14 Port E pull-up bit y (y=0..15) 14 1 PU13 Port E pull-up bit y (y=0..15) 13 1 PU12 Port E pull-up bit y (y=0..15) 12 1 PU11 Port E pull-up bit y (y=0..15) 11 1 PU10 Port E pull-up bit y (y=0..15) 10 1 PU9 Port E pull-up bit y (y=0..15) 9 1 PU8 Port E pull-up bit y (y=0..15) 8 1 PU7 Port E pull-up bit y (y=0..15) 7 1 PU6 Port E pull-up bit y (y=0..15) 6 1 PU5 Port E pull-up bit y (y=0..15) 5 1 PU4 Port E pull-up bit y (y=0..15) 4 1 PU3 Port E pull-up bit y (y=0..15) 3 1 PU2 Port E pull-up bit y (y=0..15) 2 1 PU1 Port E pull-up bit y (y=0..15) 1 1 PU0 Port E pull-up bit y (y=0..15) 0 1 PDCRE PDCRE Power Port E pull-down control register 0x44 0x20 read-write 0x00000000 PD15 Port E pull-down bit y (y=0..15) 15 1 PD14 Port E pull-down bit y (y=0..15) 14 1 PD13 Port E pull-down bit y (y=0..15) 13 1 PD12 Port E pull-down bit y (y=0..15) 12 1 PD11 Port E pull-down bit y (y=0..15) 11 1 PD10 Port E pull-down bit y (y=0..15) 10 1 PD9 Port E pull-down bit y (y=0..15) 9 1 PD8 Port E pull-down bit y (y=0..15) 8 1 PD7 Port E pull-down bit y (y=0..15) 7 1 PD6 Port E pull-down bit y (y=0..15) 6 1 PD5 Port E pull-down bit y (y=0..15) 5 1 PD4 Port E pull-down bit y (y=0..15) 4 1 PD3 Port E pull-down bit y (y=0..15) 3 1 PD2 Port E pull-down bit y (y=0..15) 2 1 PD1 Port E pull-down bit y (y=0..15) 1 1 PD0 Port E pull-down bit y (y=0..15) 0 1 PUCRF PUCRF Power Port F pull-up control register 0x48 0x20 read-write 0x00000000 PU15 Port F pull-up bit y (y=0..15) 15 1 PU14 Port F pull-up bit y (y=0..15) 14 1 PU13 Port F pull-up bit y (y=0..15) 13 1 PU12 Port F pull-up bit y (y=0..15) 12 1 PU11 Port F pull-up bit y (y=0..15) 11 1 PU10 Port F pull-up bit y (y=0..15) 10 1 PU9 Port F pull-up bit y (y=0..15) 9 1 PU8 Port F pull-up bit y (y=0..15) 8 1 PU7 Port F pull-up bit y (y=0..15) 7 1 PU6 Port F pull-up bit y (y=0..15) 6 1 PU5 Port F pull-up bit y (y=0..15) 5 1 PU4 Port F pull-up bit y (y=0..15) 4 1 PU3 Port F pull-up bit y (y=0..15) 3 1 PU2 Port F pull-up bit y (y=0..15) 2 1 PU1 Port F pull-up bit y (y=0..15) 1 1 PU0 Port F pull-up bit y (y=0..15) 0 1 PDCRF PDCRF Power Port F pull-down control register 0x4C 0x20 read-write 0x00000000 PD15 Port F pull-down bit y (y=0..15) 15 1 PD14 Port F pull-down bit y (y=0..15) 14 1 PD13 Port F pull-down bit y (y=0..15) 13 1 PD12 Port F pull-down bit y (y=0..15) 12 1 PD11 Port F pull-down bit y (y=0..15) 11 1 PD10 Port F pull-down bit y (y=0..15) 10 1 PD9 Port F pull-down bit y (y=0..15) 9 1 PD8 Port F pull-down bit y (y=0..15) 8 1 PD7 Port F pull-down bit y (y=0..15) 7 1 PD6 Port F pull-down bit y (y=0..15) 6 1 PD5 Port F pull-down bit y (y=0..15) 5 1 PD4 Port F pull-down bit y (y=0..15) 4 1 PD3 Port F pull-down bit y (y=0..15) 3 1 PD2 Port F pull-down bit y (y=0..15) 2 1 PD1 Port F pull-down bit y (y=0..15) 1 1 PD0 Port F pull-down bit y (y=0..15) 0 1 PUCRG PUCRG Power Port G pull-up control register 0x50 0x20 read-write 0x00000000 PU15 Port G pull-up bit y (y=0..15) 15 1 PU14 Port G pull-up bit y (y=0..15) 14 1 PU13 Port G pull-up bit y (y=0..15) 13 1 PU12 Port G pull-up bit y (y=0..15) 12 1 PU11 Port G pull-up bit y (y=0..15) 11 1 PU10 Port G pull-up bit y (y=0..15) 10 1 PU9 Port G pull-up bit y (y=0..15) 9 1 PU8 Port G pull-up bit y (y=0..15) 8 1 PU7 Port G pull-up bit y (y=0..15) 7 1 PU6 Port G pull-up bit y (y=0..15) 6 1 PU5 Port G pull-up bit y (y=0..15) 5 1 PU4 Port G pull-up bit y (y=0..15) 4 1 PU3 Port G pull-up bit y (y=0..15) 3 1 PU2 Port G pull-up bit y (y=0..15) 2 1 PU1 Port G pull-up bit y (y=0..15) 1 1 PU0 Port G pull-up bit y (y=0..15) 0 1 PDCRG PDCRG Power Port G pull-down control register 0x54 0x20 read-write 0x00000000 PD15 Port G pull-down bit y (y=0..15) 15 1 PD14 Port G pull-down bit y (y=0..15) 14 1 PD13 Port G pull-down bit y (y=0..15) 13 1 PD12 Port G pull-down bit y (y=0..15) 12 1 PD11 Port G pull-down bit y (y=0..15) 11 1 PD10 Port G pull-down bit y (y=0..15) 10 1 PD9 Port G pull-down bit y (y=0..15) 9 1 PD8 Port G pull-down bit y (y=0..15) 8 1 PD7 Port G pull-down bit y (y=0..15) 7 1 PD6 Port G pull-down bit y (y=0..15) 6 1 PD5 Port G pull-down bit y (y=0..15) 5 1 PD4 Port G pull-down bit y (y=0..15) 4 1 PD3 Port G pull-down bit y (y=0..15) 3 1 PD2 Port G pull-down bit y (y=0..15) 2 1 PD1 Port G pull-down bit y (y=0..15) 1 1 PD0 Port G pull-down bit y (y=0..15) 0 1 PUCRH PUCRH Power Port H pull-up control register 0x58 0x20 read-write 0x00000000 PU1 Port H pull-up bit y (y=0..1) 1 1 PU0 Port H pull-up bit y (y=0..1) 0 1 PDCRH PDCRH Power Port H pull-down control register 0x5C 0x20 read-write 0x00000000 PD1 Port H pull-down bit y (y=0..1) 1 1 PD0 Port H pull-down bit y (y=0..1) 0 1 SYSCFG System configuration controller SYSCFG 0x40010000 0x0 0x30 registers MEMRMP MEMRMP memory remap register 0x0 0x20 read-write 0x00000000 FB_MODE Flash Bank mode selection 8 1 QFS QUADSPI memory mapping swap 3 1 MEM_MODE Memory mapping selection 0 3 CFGR1 CFGR1 configuration register 1 0x4 0x20 read-write 0x7C000001 FPU_IE Floating Point Unit interrupts enable bits 26 6 I2C3_FMP I2C3 Fast-mode Plus driving capability activation 22 1 I2C2_FMP I2C2 Fast-mode Plus driving capability activation 21 1 I2C1_FMP I2C1 Fast-mode Plus driving capability activation 20 1 I2C_PB9_FMP Fast-mode Plus (Fm+) driving capability activation on PB9 19 1 I2C_PB8_FMP Fast-mode Plus (Fm+) driving capability activation on PB8 18 1 I2C_PB7_FMP Fast-mode Plus (Fm+) driving capability activation on PB7 17 1 I2C_PB6_FMP Fast-mode Plus (Fm+) driving capability activation on PB6 16 1 BOOSTEN I/O analog switch voltage booster enable 8 1 FWDIS Firewall disable 0 1 EXTICR1 EXTICR1 external interrupt configuration register 1 0x8 0x20 read-write 0x00000000 EXTI3 EXTI 3 configuration bits 12 3 EXTI2 EXTI 2 configuration bits 8 3 EXTI1 EXTI 1 configuration bits 4 3 EXTI0 EXTI 0 configuration bits 0 3 EXTICR2 EXTICR2 external interrupt configuration register 2 0xC 0x20 read-write 0x00000000 EXTI7 EXTI 7 configuration bits 12 3 EXTI6 EXTI 6 configuration bits 8 3 EXTI5 EXTI 5 configuration bits 4 3 EXTI4 EXTI 4 configuration bits 0 3 EXTICR3 EXTICR3 external interrupt configuration register 3 0x10 0x20 read-write 0x00000000 EXTI11 EXTI 11 configuration bits 12 3 EXTI10 EXTI 10 configuration bits 8 3 EXTI9 EXTI 9 configuration bits 4 3 EXTI8 EXTI 8 configuration bits 0 3 EXTICR4 EXTICR4 external interrupt configuration register 4 0x14 0x20 read-write 0x00000000 EXTI15 EXTI15 configuration bits 12 3 EXTI14 EXTI14 configuration bits 8 3 EXTI13 EXTI13 configuration bits 4 3 EXTI12 EXTI12 configuration bits 0 3 SCSR SCSR SCSR 0x18 0x20 0x00000000 SRAM2BSY SRAM2 busy by erase operation 1 1 read-only SRAM2ER SRAM2 Erase 0 1 read-write CFGR2 CFGR2 CFGR2 0x1C 0x20 0x00000000 SPF SRAM2 parity error flag 8 1 read-write ECCL ECC Lock 3 1 write-only PVDL PVD lock enable bit 2 1 write-only SPL SRAM2 parity lock bit 1 1 write-only CLL Cortex-M4 LOCKUP (Hardfault) output enable bit 0 1 write-only SWPR SWPR SWPR 0x20 0x20 write-only 0x00000000 P31WP SRAM2 page 31 write protection 31 1 P30WP P30WP 30 1 P29WP P29WP 29 1 P28WP P28WP 28 1 P27WP P27WP 27 1 P26WP P26WP 26 1 P25WP P25WP 25 1 P24WP P24WP 24 1 P23WP P23WP 23 1 P22WP P22WP 22 1 P21WP P21WP 21 1 P20WP P20WP 20 1 P19WP P19WP 19 1 P18WP P18WP 18 1 P17WP P17WP 17 1 P16WP P16WP 16 1 P15WP P15WP 15 1 P14WP P14WP 14 1 P13WP P13WP 13 1 P12WP P12WP 12 1 P11WP P11WP 11 1 P10WP P10WP 10 1 P9WP P9WP 9 1 P8WP P8WP 8 1 P7WP P7WP 7 1 P6WP P6WP 6 1 P5WP P5WP 5 1 P4WP P4WP 4 1 P3WP P3WP 3 1 P2WP P2WP 2 1 P1WP P1WP 1 1 P0WP P0WP 0 1 SKR SKR SKR 0x24 0x20 write-only 0x00000000 KEY SRAM2 write protection key for software erase 0 8 DFSDM Digital filter for sigma delta modulators DFSDM 0x40016000 0x0 0x500 registers DFSDM1_FLT3 DFSDM1_FLT3 global interrupt 42 DFSDM1_FLT0 DFSDM1_FLT0 global interrupt 61 DFSDM1_FLT1 DFSDM1_FLT1 global interrupt 62 DFSDM1_FLT2 DFSDM1_FLT2 global interrupt 63 8 0x20 0-7 CH%s DFSDM Channel cluster: contains CH?CFGR1, CH?CFGR2, CH?AWSCDR, CH?WDATR and CH?DATINR registers 0x0 CFGR1 CH0CFGR1 channel configuration y register 0x0 0x20 read-write 0x00000000 DFSDMEN DFSDMEN 31 1 DFSDMEN Disabled DFSDM interface disabled 0 Enabled DFSDM interface enabled 1 CKOUTSRC CKOUTSRC 30 1 CKOUTSRC SYSCLK Source for output clock is from system clock 0 AUDCLK Source for output clock is from audio clock 1 CKOUTDIV CKOUTDIV 16 8 0 255 DATPACK DATPACK 14 2 DATPACK Standard Standard: input data in DFSDM_CHyDATINR register are stored only in INDAT0[15:0]. To empty DFSDM_CHyDATINR register one sample must be read by the DFSDM filter from channel y 0 Interleaved : Interleaved: input data in DFSDM_CHyDATINR register are stored as two samples: –first sample in INDAT0[15:0] (assigned to channel y) –second sample INDAT1[15:0] (assigned to channel y) 1 Dual Dual: input data in DFSDM_CHyDATINR register are stored as two samples: –first sample INDAT0[15:0] (assigned to channel y) –second sample INDAT1[15:0] (assigned to channel y+1) 2 DATMPX DATMPX 12 2 DATMPX External Data to channel y are taken from external serial inputs as 1-bit values. DFSDM_CHyDATINR register is write protected 0 ADC Data to channel y are taken from internal analog to digital converter ADCy+1 output register update as 16-bit values (if ADCy+1 is available). Data from ADCs are written into INDAT0[15:0] part of DFSDM_CHyDATINR register 1 Internal Data to channel y are taken from internal DFSDM_CHyDATINR register by direct CPU/DMA write. There can be written one or two 16-bit data samples according DATPACK[1:0] bit field setting 2 CHINSEL CHINSEL 8 1 CHINSEL SameChannel Channel inputs are taken from pins of the same channel y 0 FollowingChannel Channel inputs are taken from pins of the following channel (channel (y+1) modulo 8) 1 CHEN CHEN 7 1 CHEN Disabled Channel y disabled 0 Enabled Channel y enabled 1 CKABEN CKABEN 6 1 CKABEN Disabled Clock absence detector disabled on channel y 0 Enabled Clock absence detector enabled on channel y 1 SCDEN SCDEN 5 1 SCDEN Disabled Input channel y will not be guarded by the short-circuit detector 0 Enabled Input channel y will be continuously guarded by the short-circuit detector 1 SPICKSEL SPICKSEL 2 2 SPICKSEL CKIN Clock coming from external CKINy input - sampling point according SITP[1:0] 0 CKOUT Clock coming from internal CKOUT output - sampling point according SITP[1:0] 1 CKOUTSecondFalling Clock coming from internal CKOUT - sampling point on each second CKOUT falling edge. For connection to external Σ∆ modulator which divides its clock input (from CKOUT) by 2 to generate its output serial communication clock (and this output clock change is active on each clock input rising edge) 2 CKOUTSecondRising Clock coming from internal CKOUT output - sampling point on each second CKOUT rising edge. For connection to external Σ∆ modulator which divides its clock input (from CKOUT) by 2 to generate its output serial communication clock (and this output clock change is active on each clock input falling edge) 3 SITP SITP 0 2 SITP SPIRisingEdge SPI with rising edge to strobe data 0 SPIFallingEdge SPI with falling edge to strobe data 1 Manchester Manchester coded input on DATINy pin: rising edge = logic 0, falling edge = logic 1 2 ManchesterInverted Manchester coded input on DATINy pin: rising edge = logic 1, falling edge = logic 0 3 CFGR2 CH0CFGR2 channel configuration y register 0x4 0x20 read-write 0x00000000 OFFSET OFFSET 8 24 0 16777215 DTRBS DTRBS 3 5 0 31 AWSCDR CH0AWSCDR analog watchdog and short-circuit detector register 0x8 0x20 read-write 0x00000000 AWFORD AWFORD 22 2 AWFORD FastSinc FastSinc filter type 0 Sinc1 Sinc1 filter type 1 Sinc2 Sinc2 filter type 2 Sinc3 Sinc3 filter type 3 AWFOSR AWFOSR 16 5 0 31 BKSCD BKSCD 12 4 0 15 SCDT SCDT 0 8 0 255 WDATR CH0WDATR channel watchdog filter data register 0xC 0x20 read-write 0x00000000 WDATA WDATA 0 16 0 65535 DATINR CH0DATINR channel data input register 0x10 0x20 read-write 0x00000000 INDAT1 INDAT1 16 16 0 65535 INDAT0 INDAT0 0 16 0 65535 DLYR CH0DLYR channel y delay register 0x14 0x20 read-write 0x00000000 PLSSKP PLSSKP 0 6 0 63 4 0x80 0-3 FLT%s Cluster FLT%s, containing FLT?CR1, FLT?CR2, FLT?ISR, FLT?ICR, FLT?JCHGR, FLT?FCR, FLT?JDATAR, FLT?RDATAR, FLT?AWHTR, FLT?AWLTR, FLT?AWSR, FLT?AWCFR, FLT?EXMAX, FLT?EXMIN, FLT?CNVTIMR 0x100 CR1 FLT0CR1 control register 1 0x0 0x20 read-write 0x00000000 AWFSEL Analog watchdog fast mode select 30 1 AWFSEL Output Analog watchdog on data output value (after the digital filter). The comparison is done after offset correction and shift 0 Transceiver Analog watchdog on channel transceivers value (after watchdog filter) 1 FAST Fast conversion mode selection for regular conversions 29 1 FAST Disabled Fast conversion mode disabled 0 Enabled Fast conversion mode enabled 1 RCH Regular channel selection 24 3 RCH Channel0 Channel 0 is selected as regular channel 0 Channel1 Channel 1 is selected as regular channel 1 Channel2 Channel 2 is selected as regular channel 2 Channel3 Channel 3 is selected as regular channel 3 Channel4 Channel 4 is selected as regular channel 4 Channel5 Channel 5 is selected as regular channel 5 Channel6 Channel 6 is selected as regular channel 6 Channel7 Channel 7 is selected as regular channel 7 RDMAEN DMA channel enabled to read data for the regular conversion 21 1 RDMAEN Disabled The DMA channel is not enabled to read regular data 0 Enabled The DMA channel is enabled to read regular data 1 RSYNC Launch regular conversion synchronously with DFSDM0 19 1 RSYNC NoLaunch Do not launch a regular conversion synchronously with DFSDM_FLT0 0 Launch Launch a regular conversion in this DFSDM_FLTx at the very moment when a regular conversion is launched in DFSDM_FLT0 1 RCONT Continuous mode selection for regular conversions 18 1 RCONT Once The regular channel is converted just once for each conversion request 0 Continuous The regular channel is converted repeatedly after each conversion request 1 RSWSTART Software start of a conversion on the regular channel 17 1 RSWSTARTW write Start Writing ‘1’ makes a request to start a conversion on the regular channel and causes RCIP to become ‘1’. If RCIP=1 already, writing to RSWSTART has no effect. Writing ‘1’ has no effect if RSYNC=1 1 JEXTEN Trigger enable and trigger edge selection for injected conversions 13 2 JEXTEN Disabled Trigger detection is disabled 0 RisingEdge Each rising edge on the selected trigger makes a request to launch an injected conversion 1 FallingEdge Each falling edge on the selected trigger makes a request to launch an injected conversion 2 BothEdges Both rising edges and falling edges on the selected trigger make requests to launch injected conversions 3 JEXTSEL Trigger signal selection for launching injected conversions 8 3 JDMAEN DMA channel enabled to read data for the injected channel group 5 1 JDMAEN Disabled The DMA channel is not enabled to read injected data 0 Enabled The DMA channel is enabled to read injected data 1 JSCAN Scanning conversion mode for injected conversions 4 1 JSCAN Single One channel conversion is performed from the injected channel group and next the selected channel from this group is selected 0 Series The series of conversions for the injected group channels is executed, starting over with the lowest selected channel 1 JSYNC Launch an injected conversion synchronously with the DFSDM0 JSWSTART trigger 3 1 JSYNC Disabled Do not launch an injected conversion synchronously with DFSDM_FLT0 0 Enabled Launch an injected conversion in this DFSDM_FLTx at the very moment when an injected conversion is launched in DFSDM_FLT0 by its JSWSTART trigger 1 JSWSTART Start a conversion of the injected group of channels 1 1 JSWSTARTW write Start Writing ‘1’ makes a request to convert the channels in the injected conversion group, causing JCIP to become ‘1’ at the same time. If JCIP=1 already, then writing to JSWSTART has no effect. Writing ‘1’ has no effect if JSYNC=1 1 DFEN DFSDM enable 0 1 DFEN Disabled DFSDM_FLTx is disabled. All conversions of given DFSDM_FLTx are stopped immediately and all DFSDM_FLTx functions are stopped 0 Enabled DFSDM_FLTx is enabled. If DFSDM_FLTx is enabled, then DFSDM_FLTx starts operating according to its setting 1 CR2 FLT0CR2 control register 2 0x4 0x20 read-write 0x00000000 AWDCH Analog watchdog channel selection 16 8 AWDCH Disabled Analog watchdog is disabled on channel y 0 Enabled Analog watchdog is enabled on channel y 1 EXCH Extremes detector channel selection 8 8 EXCH Disabled Extremes detector does not accept data from channel y 0 Enabled Extremes detector accepts data from channel y 1 CKABIE Clock absence interrupt enable 6 1 CKABIE Disabled Detection of channel input clock absence interrupt is disabled 0 Enabled Detection of channel input clock absence interrupt is enabled 1 SCDIE Short-circuit detector interrupt enable 5 1 SCDIE Disabled Short-circuit detector interrupt is disabled 0 Enabled Short-circuit detector interrupt is enabled 1 AWDIE Analog watchdog interrupt enable 4 1 AWDIE Disabled Analog watchdog interrupt is disabled 0 Enabled Analog watchdog interrupt is enabled 1 ROVRIE Regular data overrun interrupt enable 3 1 ROVRIE Disabled Regular data overrun interrupt is disabled 0 Enabled Regular data overrun interrupt is enabled 1 JOVRIE Injected data overrun interrupt enable 2 1 JOVRIE Disabled Injected data overrun interrupt is disabled 0 Enabled Injected data overrun interrupt is enabled 1 REOCIE Regular end of conversion interrupt enable 1 1 REOCIE Disabled Regular end of conversion interrupt is disabled 0 Enabled Regular end of conversion interrupt is enabled 1 JEOCIE Injected end of conversion interrupt enable 0 1 JEOCIE Disabled Injected end of conversion interrupt is disabled 0 Enabled Injected end of conversion interrupt is enabled 1 ISR FLT0ISR interrupt and status register 0x8 0x20 read-only 0x00FF0000 SCDF short-circuit detector flag 24 8 SCDF Clear No short-circuit detector event occurred on channel y 0 Set The short-circuit detector counter reaches, on channel y, the value programmed in the DFSDM_CHyAWSCDR registers 1 CKABF Clock absence flag 16 8 CKABF Clear Clock signal on channel y is present. 0 Set Clock signal on channel y is not present 1 RCIP Regular conversion in progress status 14 1 RCIP NotInProgress No request to convert the regular channel has been issued 0 InProgress The conversion of the regular channel is in progress or a request for a regular conversion is pending 1 JCIP Injected conversion in progress status 13 1 JCIP NotInProgress No request to convert the injected channel group (neither by software nor by trigger) has been issued 0 InProgress The conversion of the injected channel group is in progress or a request for a injected conversion is pending, due either to ‘1’ being written to JSWSTART or to a trigger detection 1 AWDF Analog watchdog 4 1 AWDF Clear No Analog watchdog event occurred 0 Set The analog watchdog block detected voltage which crosses the value programmed in the DFSDM_FLTxAWLTR or DFSDM_FLTxAWHTR registers 1 ROVRF Regular conversion overrun flag 3 1 ROVRF Clear No regular conversion overrun has occurred 0 Set A regular conversion overrun has occurred, which means that a regular conversion finished while REOCF was already ‘1’. RDATAR is not affected by overruns 1 JOVRF Injected conversion overrun flag 2 1 JOVRF Clear No injected conversion overrun has occurred 0 Set An injected conversion overrun has occurred, which means that an injected conversion finished while JEOCF was already ‘1’. JDATAR is not affected by overruns 1 REOCF End of regular conversion flag 1 1 REOCF Clear No regular conversion has completed 0 Set A regular conversion has completed and its data may be read 1 JEOCF End of injected conversion flag 0 1 JEOCF Clear No injected conversion has completed 0 Set An injected conversion has completed and its data may be read 1 ICR FLT0ICR interrupt flag clear register 0xC 0x20 read-write 0x00000000 CLRSCDF Clear the short-circuit detector flag 24 8 0 255 CLRCKABF Clear the clock absence flag 16 8 0 255 CLRROVRF Clear the regular conversion overrun flag 3 1 CLRROVRFW write Clear Writing ‘1’ clears the ROVRF bit in the DFSDM_FLTxISR register 1 CLRJOVRF Clear the injected conversion overrun flag 2 1 CLRJOVRFW write Clear Writing ‘1’ clears the JOVRF bit in the DFSDM_FLTxISR register 1 JCHGR FLT0JCHGR injected channel group selection register 0x10 0x20 read-write 0x00000001 JCHG Injected channel group selection 0 8 0 255 FCR FLT0FCR filter control register 0x14 0x20 read-write 0x00000000 FORD Sinc filter order 29 3 FORD FastSinc FastSinc filter type 0 Sinc1 Sinc1 filter type 1 Sinc2 Sinc2 filter type 2 Sinc3 Sinc3 filter type 3 Sinc4 Sinc4 filter type 4 Sinc5 Sinc5 filter type 5 FOSR Sinc filter oversampling ratio (decimation rate) 16 10 0 1023 IOSR Integrator oversampling ratio (averaging length) 0 8 0 255 JDATAR FLT0JDATAR data register for injected group 0x18 0x20 read-only 0x00000000 JDATA Injected group conversion data 8 24 0 16777215 JDATACH Injected channel most recently converted 0 3 0 7 RDATAR FLT0RDATAR data register for the regular channel 0x1C 0x20 read-only 0x00000000 RDATA Regular channel conversion data 8 24 0 16777215 RPEND Regular channel pending data 4 1 RDATACH Regular channel most recently converted 0 3 0 7 AWHTR FLT0AWHTR analog watchdog high threshold register 0x20 0x20 read-write 0x00000000 AWHT Analog watchdog high threshold 8 24 0 16777215 4 0x1 0-3 BKAWH%s Break signal assignment to analog watchdog high threshold event 0 1 BKAWH0 NotAssigned Break i signal is not assigned to an analog watchdog high threshold event 0 Assigned Break i signal is assigned to an analog watchdog high threshold event 1 AWLTR FLT0AWLTR analog watchdog low threshold register 0x24 0x20 read-write 0x00000000 AWLT Analog watchdog low threshold 8 24 0 16777215 4 0x1 0-3 BKAWL%s Break signal assignment to analog watchdog low threshold event 0 1 BKAWL0 NotAssigned Break i signal is not assigned to an analog watchdog low threshold event 0 Assigned Break i signal is assigned to an analog watchdog low threshold event 1 AWSR FLT0AWSR analog watchdog status register 0x28 0x20 read-only 0x00000000 8 0x1 0-7 AWHTF%s Analog watchdog high threshold flag 8 1 AWHTF0 NoError No high threshold error 0 Error A high threshold error on channel y 1 8 0x1 0-7 AWLTF%s Analog watchdog low threshold flag 0 1 AWLTF0 NoError No low threshold error 0 Error A low threshold error on channel y 1 AWCFR FLT0AWCFR analog watchdog clear flag register 0x2C 0x20 read-write 0x00000000 8 0x1 0-7 CLRAWHTF%s Clear the analog watchdog high threshold flag 8 1 oneToClear CLRAWHTF0W write Clear Clear the corresponding AWHTF[y] bit 1 8 0x1 0-7 CLRAWLTF%s Clear the analog watchdog low threshold flag 0 1 oneToClear CLRAWLTF0W write Clear Clear the corresponding AWLTF[y] bit 1 EXMAX FLT0EXMAX Extremes detector maximum register 0x30 0x20 read-only 0x80000000 EXMAX Extremes detector maximum value 8 24 0 16777215 EXMAXCH Extremes detector maximum data channel 0 3 0 7 EXMIN FLT0EXMIN Extremes detector minimum register 0x34 0x20 read-only 0x7FFFFF00 EXMIN EXMIN 8 24 0 16777215 EXMINCH Extremes detector minimum data channel 0 3 0 7 CNVTIMR FLT0CNVTIMR conversion timer register 0x38 0x20 read-only 0x00000000 CNVCNT 28-bit timer counting conversion time t = CNVCNT[27:0] / fDFSDM_CKIN 4 28 0 268435455 RNG Random number generator RNG 0x50060800 0x0 0x400 registers RNG_HASH RNG and HASH global interrupt 80 CR CR control register 0x0 0x20 read-write 0x00000000 IE Interrupt enable 3 1 IE Disabled RNG interrupt is disabled 0 Enabled RNG interrupt is enabled 1 RNGEN Random number generator enable 2 1 RNGEN Disabled Random number generator is disabled 0 Enabled Random number generator is enabled 1 SR SR status register 0x4 0x20 0x00000000 CEIS Clock error interrupt status 5 1 read-write zeroToClear CEISW write Clear Clear flag 0 CEISR read Correct The RNG clock is correct 0 Slow The RNG has been detected too slow An interrupt is pending if IE = 1 in the RNG_CR register 1 SEIS Seed error interrupt status 6 1 read-write zeroToClear write SEISR read NoFault No faulty sequence detected 0 Fault At least one faulty sequence has been detected. See **SECS** bit description for details. An interrupt is pending if IE = 1 in the RNG_CR register. 1 SECS Seed error current status 2 1 read-only SECS NoFault No faulty sequence has currently been detected. If the SEIS bit is set, this means that a faulty sequence was detected and the situation has been recovered. 0 Fault At least one faulty sequence has been detected - see ref manual for details 1 CECS Clock error current status 1 1 read-only CECS Correct The RNG clock is correct. If the CEIS bit is set, this means that a slow clock was detected and the situation has been recovered. 0 Slow The RNG clock is too slow 1 DRDY Data ready 0 1 read-only DRDY Invalid The RNG_DR register is not yet valid, no random data is available 0 Valid The RNG_DR register contains valid random data. Once the RNG_DR register has been read, this bit returns to 0 until a new random value is generated. 1 DR DR data register 0x8 0x20 read-only 0x00000000 RNDATA Random data 0 32 0 4294967295 AES Advanced encryption standard hardware accelerator AES 0x50060000 0x0 0x400 registers AES AES global interrupt 79 CR CR control register 0x0 0x20 read-write 0x00000000 DMAOUTEN Enable DMA management of data output phase 12 1 DMAOUTEN Disabled Disable DMA Output 0 Enabled Enabled DMA Output 1 DMAINEN Enable DMA management of data input phase 11 1 DMAINEN Disabled Disable DMA Input 0 Enabled Enable DMA Input 1 ERRIE Error interrupt enable 10 1 ERRIE Disabled Disable (mask) error interrupt 0 Enabled Enable error interrupt 1 CCFIE CCF flag interrupt enable 9 1 CCFIE Disabled Disable (mask) CCF interrupt 0 Enabled Enable CCF interrupt 1 ERRC Error clear 8 1 ERRCW write Clear Clear RDERR and WRERR flags 1 CCFC Computation Complete Flag Clear 7 1 CCFCW write Clear Clear computation complete flag 1 CHMOD AES chaining mode 5 2 CHMOD ECB Electronic codebook (ECB) / Counter with CBC-MAC (CCM) if CHMOD2 is 1 0 CBC Cipher-block chaining (CBC) 1 CTR Counter mode (CTR) 2 GCM Galois counter mode (GCM) and Galois message authentication code (GMAC) 3 MODE AES operating mode 3 2 MODE Mode1 Mode 1: encryption 0 Mode2 Mode 2: key derivation (or key preparation for ECB/CBC decryption) 1 Mode3 Mode 3: decryption 2 Mode4 Mode 4: key derivation then single decryption 3 DATATYPE Data type selection (for data in and data out to/from the cryptographic block) 1 2 DATATYPE None Word 0 HalfWord Half-word (16-bit) 1 Byte Byte (8-bit) 2 Bit Bit 3 EN AES enable 0 1 EN Disabled Disable AES 0 Enabled Enable AES 1 KEYSIZE Key size selection 18 1 KEYSIZE AES128 128 0 AES256 256 1 CHMOD_2 Chaining mode selection, bit [2] 16 1 CHMOD_2 CHMOD Mode as per CHMOD (ECB, CBC, CTR, GCM) 0 CCM Counter with CBC-MAC (CCM) - CHMOD must be 0 (ECB) 1 GCMPH GCM or CCM phase selection 13 2 GCMPH Init Init phase 0 Header Header phase 1 Payload Payload phase 2 Final Final Phase 3 SR SR status register 0x4 0x20 read-only 0x00000000 WRERR Write error flag 2 1 WRERR NoError Write error not detected 0 Error Write error detected 1 RDERR Read error flag 1 1 RDERR NoError Read error not detected 0 Error Read error detected 1 CCF Computation complete flag 0 1 CCF Complete Computation complete 0 NotComplete Computation not complete 1 BUSY Busy 3 1 BUSY Idle Idle 0 Busy Busy 1 DINR DINR data input register 0x8 0x20 read-write 0x00000000 DIN Data Input Register 0 32 0 4294967295 DOUTR DOUTR data output register 0xC 0x20 read-only 0x00000000 DOUT Data output register 0 32 0 4294967295 KEYR0 KEYR0 key register 0 0x10 0x20 read-write 0x00000000 KEY Data Output Register (LSB key [31:0]) 0 32 0 4294967295 KEYR1 KEYR1 key register 1 0x14 0x20 read-write 0x00000000 KEY AES key register (key [63:32]) 0 32 0 4294967295 KEYR2 KEYR2 key register 2 0x18 0x20 read-write 0x00000000 KEY AES key register (key [95:64]) 0 32 0 4294967295 KEYR3 KEYR3 key register 3 0x1C 0x20 read-write 0x00000000 KEY AES key register (MSB key [127:96]) 0 32 0 4294967295 IVR0 IVR0 initialization vector register 0 0x20 0x20 read-write 0x00000000 IVI initialization vector register (LSB IVR [31:0]) 0 32 0 4294967295 IVR1 IVR1 initialization vector register 1 0x24 0x20 read-write 0x00000000 IVI Initialization Vector Register (IVR [63:32]) 0 32 0 4294967295 IVR2 IVR2 initialization vector register 2 0x28 0x20 read-write 0x00000000 IVI Initialization Vector Register (IVR [95:64]) 0 32 0 4294967295 IVR3 IVR3 initialization vector register 3 0x2C 0x20 read-write 0x00000000 IVI Initialization Vector Register (MSB IVR [127:96]) 0 32 0 4294967295 KEYR4 key register 4 0x30 0x20 read-write 0x00000000 KEY Cryptographic key, bits [159:128] 0 32 0 4294967295 KEYR5 key register 5 0x34 0x20 read-write 0x00000000 KEY Cryptographic key, bits [191:160] 0 32 0 4294967295 KEYR6 key register 6 0x38 0x20 read-write 0x00000000 KEY Cryptographic key, bits [223:192] 0 32 0 4294967295 KEYR7 key register 7 0x3C 0x20 read-write 0x00000000 KEY Cryptographic key, bits [255:224] 0 32 0 4294967295 SUSP0R suspend registers 0x40 0x20 read-write 0x00000000 SUSP AES suspend 0 32 0 4294967295 SUSP1R suspend registers 0x44 0x20 read-write 0x00000000 SUSP AES suspend 0 32 0 4294967295 SUSP2R suspend registers 0x48 0x20 read-write 0x00000000 SUSP AES suspend 0 32 0 4294967295 SUSP3R suspend registers 0x4C 0x20 read-write 0x00000000 SUSP AES suspend 0 32 0 4294967295 SUSP4R suspend registers 0x50 0x20 read-write 0x00000000 SUSP AES suspend 0 32 0 4294967295 SUSP5R suspend registers 0x54 0x20 read-write 0x00000000 SUSP AES suspend 0 32 0 4294967295 SUSP6R suspend registers 0x58 0x20 read-write 0x00000000 SUSP AES suspend 0 32 0 4294967295 SUSP7R suspend registers 0x5C 0x20 read-write 0x00000000 SUSP AES suspend 0 32 0 4294967295 ADC1 Analog-to-Digital Converter ADC 0x50040000 0x0 0xB9 registers ADC1_2 ADC1 and ADC2 global interrupt 18 ADC3 ADC3 global interrupt 47 ISR ISR interrupt and status register 0x0 0x20 read-write 0x00000000 JQOVF JQOVF 10 1 oneToClear JQOVFR read NoOverflow No injected context queue overflow has occurred 0 Overflow Injected context queue overflow has occurred 1 JQOVFW write Clear Clear injected context queue overflow flag 1 3 0x1 1-3 AWD%s Analog watchdog %s flag 7 1 oneToClear AWD1R read NoEvent No analog watchdog event occurred 0 Event Analog watchdog event occurred 1 AWD1W write Clear Clear analog watchdog event occurred flag 1 JEOS JEOS 6 1 oneToClear JEOSR read NotComplete Injected sequence is not complete 0 Complete Injected sequence complete 1 JEOSW write Clear Clear Injected sequence complete flag 1 JEOC JEOC 5 1 oneToClear JEOCR read NotComplete Injected conversion is not complete 0 Complete Injected conversion complete 1 JEOCW write Clear Clear injected conversion complete flag 1 OVR OVR 4 1 oneToClear OVRR read NoOverrun No overrun occurred 0 Overrun Overrun occurred 1 OVRW write Clear Clear overrun occurred flag 1 EOS EOS 3 1 oneToClear EOSR read NotComplete Regular sequence is not complete 0 Complete Regular sequence complete 1 EOSW write Clear Clear regular sequence complete flag 1 EOC EOC 2 1 oneToClear EOCR read NotComplete Regular conversion is not complete 0 Complete Regular conversion complete 1 EOCW write Clear Clear regular conversion complete flag 1 EOSMP EOSMP 1 1 oneToClear EOSMPR read NotEnded End of sampling phase no yet reached 0 Ended End of sampling phase reached 1 EOSMPW write Clear Clear end of sampling phase reached flag 1 ADRDY ADRDY 0 1 oneToClear ADRDYR read NotReady ADC is not ready to start conversion 0 Ready ADC is ready to start conversion 1 ADRDYW write Clear Clear ADC is ready to start conversion flag 1 IER IER interrupt enable register 0x4 0x20 read-write 0x00000000 JQOVFIE JQOVFIE 10 1 JQOVFIE Disabled Injected context queue overflow interrupt disabled 0 Enabled Injected context queue overflow interrupt enabled 1 3 0x1 1-3 AWD%sIE Analog watchdog %s interrupt enable 7 1 AWD1IE Disabled Analog watchdog interrupt disabled 0 Enabled Analog watchdog interrupt enabled 1 JEOSIE JEOSIE 6 1 JEOSIE Disabled End of injected sequence interrupt disabled 0 Enabled End of injected sequence interrupt enabled 1 JEOCIE JEOCIE 5 1 JEOCIE Disabled End of injected conversion interrupt disabled 0 Enabled End of injected conversion interrupt enabled 1 OVRIE OVRIE 4 1 OVRIE Disabled Overrun interrupt disabled 0 Enabled Overrun interrupt enabled 1 EOSIE EOSIE 3 1 EOSIE Disabled End of regular sequence interrupt disabled 0 Enabled End of regular sequence interrupt enabled 1 EOCIE EOCIE 2 1 EOCIE Disabled End of regular conversion interrupt disabled 0 Enabled End of regular conversion interrupt enabled 1 EOSMPIE EOSMPIE 1 1 EOSMPIE Disabled End of regular conversion sampling phase interrupt disabled 0 Enabled End of regular conversion sampling phase interrupt enabled 1 ADRDYIE ADRDYIE 0 1 ADRDYIE Disabled ADC ready interrupt disabled 0 Enabled ADC ready interrupt enabled 1 CR CR control register 0x8 0x20 read-write 0x00000000 ADCAL ADCAL 31 1 oneToSet ADCALR read NotCalibrating ADC calibration either not yet performed or completed 0 Calibrating ADC calibration in progress 1 ADCALW write StartCalibration Start the ADC calibration sequence 1 ADCALDIF ADCALDIF 30 1 ADCALDIF SingleEnded Calibration for single-ended mode 0 Differential Calibration for differential mode 1 DEEPPWD DEEPPWD 29 1 DEEPPWD NotDeepPowerDown ADC not in Deep-power down 0 DeepPowerDown ADC in Deep-power-down (default reset state) 1 ADVREGEN ADVREGEN 28 1 ADVREGEN Disabled ADC Voltage regulator disabled 0 Enabled ADC Voltage regulator enabled 1 ADSTP ADSTP 4 1 oneToSet ADSTPR read NotStopping No stop command active 0 Stopping ADC stopping conversion 1 ADSTPW write StopConversion Stop the active conversion 1 JADSTP JADSTP 5 1 oneToSet read write ADSTART ADSTART 2 1 oneToSet ADSTARTR read NotActive No conversion ongoing 0 Active ADC operating and may be converting 1 ADSTARTW write StartConversion Start the ADC conversion (may be delayed for hardware triggers) 1 JADSTART JADSTART 3 1 oneToSet read write ADDIS ADDIS 1 1 oneToSet ADDISR read NotDisabling No disable command active 0 Disabling ADC disabling 1 ADDISW write Disable Disable the ADC 1 ADEN ADEN 0 1 oneToSet ADENR read Disabled ADC disabled 0 Enabled ADC enabled 1 ADENW write Enabled Enable the ADC 1 CFGR CFGR configuration register 0xC 0x20 read-write 0x00000000 JQDIS Injected Queue disable 31 1 AWD1CH AWDCH1CH 26 5 0 18 JAUTO JAUTO 25 1 JAUTO Disabled Automatic injected group conversion disabled 0 Enabled Automatic injected group conversion enabled 1 JAWD1EN JAWD1EN 24 1 JAWD1EN Disabled Analog watchdog 1 disabled on injected channels 0 Enabled Analog watchdog 1 enabled on injected channels 1 AWD1EN AWD1EN 23 1 AWD1EN Disabled Analog watchdog 1 disabled on regular channels 0 Enabled Analog watchdog 1 enabled on regular channels 1 AWD1SGL AWD1SGL 22 1 AWD1SGL All Analog watchdog 1 enabled on all channels 0 Single Analog watchdog 1 enabled on single channel selected in AWD1CH 1 JQM JQM 21 1 JQM Mode0 JSQR Mode 0: Queue maintains the last written configuration into JSQR 0 Mode1 JSQR Mode 1: An empty queue disables software and hardware triggers of the injected sequence 1 JDISCEN JDISCEN 20 1 JDISCEN Disabled Discontinuous mode on injected channels disabled 0 Enabled Discontinuous mode on injected channels enabled 1 DISCNUM DISCNUM 17 3 0 7 DISCEN DISCEN 16 1 DISCEN Disabled Discontinuous mode on regular channels disabled 0 Enabled Discontinuous mode on regular channels enabled 1 AUTDLY AUTDLY 14 1 AUTDLY Off Auto delayed conversion mode off 0 On Auto delayed conversion mode on 1 CONT CONT 13 1 CONT Single Single conversion mode 0 Continuous Continuous conversion mode 1 OVRMOD OVRMOD 12 1 OVRMOD Preserve Preserve DR register when an overrun is detected 0 Overwrite Overwrite DR register when an overrun is detected 1 EXTEN EXTEN 10 2 EXTEN Disabled Trigger detection disabled 0 RisingEdge Trigger detection on the rising edge 1 FallingEdge Trigger detection on the falling edge 2 BothEdges Trigger detection on both the rising and falling edges 3 EXTSEL EXTSEL 6 4 EXTSEL TIM1_CC1 Timer 1 CC1 event 0 TIM1_CC2 Timer 1 CC2 event 1 TIM1_CC3 Timer 1 CC3 event 2 TIM2_CC2 Timer 2 CC2 event 3 TIM3_TRGO Timer 3 TRGO event 4 EXTI11 EXTI line 11 6 TIM1_TRGO Timer 1 TRGO event 9 TIM1_TRGO2 Timer 1 TRGO2 event 10 TIM2_TRGO Timer 2 TRGO event 11 TIM6_TRGO Timer 6 TRGO event 13 TIM15_TRGO Timer 15 TRGO event 14 TIM3_CC4 Timer 3 CC4 event 15 ALIGN ALIGN 5 1 ALIGN Right Right alignment 0 Left Left alignment 1 RES RES 3 2 RES Bits12 12-bit 0 Bits10 10-bit 1 Bits8 8-bit 2 Bits6 6-bit 3 DFSDMCFG DFSDMCFG 2 1 DMACFG DMACFG 1 1 DMACFG OneShot DMA One Shot mode selected 0 Circular DMA Circular mode selected 1 DMAEN DMAEN 0 1 DMAEN Disabled DMA disabled 0 Enabled DMA enabled 1 CFGR2 CFGR2 configuration register 0x10 0x20 read-write 0x00000000 ROVSM EXTEN 10 1 ROVSM ContinuedMode When injected conversions are triggered, the oversampling is temporary stopped and continued after the injection sequence (oversampling buffer is maintained during injected sequence) 0 ResumedMode When injected conversions are triggered, the current oversampling is aborted and resumed from start after the injection sequence (oversampling buffer is zeroed by injected sequence start) 1 TROVS Triggered Regular Oversampling 9 1 TROVS All All oversampled conversions for a channel are done consecutively following a trigger 0 Single Each oversampled conversion for a channel needs a new trigger 1 OVSS ALIGN 5 4 OVSS NoShift No Shift 0 Shift1Bit Shift 1-bit 1 Shift2Bit Shift 2-bit 2 Shift3Bit Shift 3-bit 3 Shift4Bit Shift 4-bit 4 Shift5Bit Shift 5-bit 5 Shift6Bit Shift 6-bit 6 Shift7Bit Shift 7-bit 7 Shift8Bit Shift 8-bit 8 OVSR RES 2 3 OVSR Ratio2 2x 0 Ratio4 4x 1 Ratio8 8x 2 Ratio16 16x 3 Ratio32 32x 4 Ratio64 64x 5 Ratio128 128x 6 Ratio256 256x 7 JOVSE DMACFG 1 1 JOVSE Disabled Injected Oversampling disabled 0 Enabled Injected Oversampling enabled 1 ROVSE DMAEN 0 1 ROVSE Disabled Regular Oversampling disabled 0 Enabled Regular Oversampling enabled 1 SMPR1 SMPR1 sample time register 1 0x14 0x20 read-write 0x00000000 10 0x3 0-9 SMP%s Channel %s sample time selection 0 3 SMP0 Cycles2_5 2.5 ADC clock cycles 0 Cycles6_5 6.5 ADC clock cycles 1 Cycles12_5 12.5 ADC clock cycles 2 Cycles24_5 24.5 ADC clock cycles 3 Cycles47_5 47.5 ADC clock cycles 4 Cycles92_5 92.5 ADC clock cycles 5 Cycles247_5 247.5 ADC clock cycles 6 Cycles640_5 640.5 ADC clock cycles 7 SMPPLUS Addition of one clock cycle to the sampling time 31 1 SMPPLUS KeepCycles The sampling time remains set to 2.5 ADC clock cycles remains 0 Add1Cycle 2.5 ADC clock cycle sampling time becomes 3.5 ADC clock cycles for the ADC_SMPR1 and ADC_SMPR2 registers 1 SMPR2 SMPR2 sample time register 2 0x18 0x20 read-write 0x00000000 9 0x3 10-18 SMP%s Channel %s sample time selection 0 3 TR1 TR1 watchdog threshold register 1 0x20 0x20 read-write 0x0FFF0000 HT1 HT1 16 12 0 4095 LT1 LT1 0 12 0 4095 TR2 TR2 watchdog threshold register 0x24 0x20 read-write 0x0FFF0000 HT2 HT2 16 8 0 255 LT2 LT2 0 8 0 255 TR3 TR3 watchdog threshold register 3 0x28 0x20 read-write 0x0FFF0000 HT3 HT3 16 8 0 255 LT3 LT3 0 8 0 255 SQR1 SQR1 regular sequence register 1 0x30 0x20 read-write 0x00000000 4 0x6 1-4 SQ%s %s conversion in regular sequence 6 5 0 18 L Regular channel sequence length 0 4 0 15 SQR2 SQR2 regular sequence register 2 0x34 0x20 read-write 0x00000000 5 0x6 5-9 SQ%s %s conversion in regular sequence 0 5 SQR3 SQR3 regular sequence register 3 0x38 0x20 read-write 0x00000000 5 0x6 10-14 SQ%s %s conversion in regular sequence 0 5 SQR4 SQR4 regular sequence register 4 0x3C 0x20 read-write 0x00000000 2 0x6 15-16 SQ%s %s conversion in regular sequence 0 5 DR DR regular Data Register 0x40 0x20 read-only 0x00000000 RDATA Regular Data converted 0 16 0 65535 JSQR JSQR injected sequence register 0x4C 0x20 read-write 0x00000000 4 0x6 1-4 JSQ%s %s conversion in injected sequence 8 5 0 19 JEXTEN JEXTEN 6 2 JEXTEN Disabled Trigger detection disabled 0 RisingEdge Trigger detection on the rising edge 1 FallingEdge Trigger detection on the falling edge 2 BothEdges Trigger detection on both the rising and falling edges 3 JEXTSEL JEXTSEL 2 4 JEXTSEL TIM1_TRGO Timer 1 TRGO event 0 TIM1_CC4 Timer 1 CC4 event 1 TIM2_TRGO Timer 2 TRGO event 2 TIM2_CC1 Timer 2 CC1 event 3 TIM3_CC4 Timer 3 CC4 event 4 EXTI15 EXTI line 15 6 TIM1_TRGO2 Timer 1 TRGO2 event 8 TIM3_CC3 Timer 3 CC3 event 11 TIM3_TRGO Timer 3 TRGO event 12 TIM3_CC1 Timer 3 CC1 event 13 TIM6_TRGO Timer 6 TRGO event 14 TIM15_TRGO Timer 15 TRGO event 15 JL JL 0 2 0 3 4 0x4 1-4 OFR%s OFR%s offset register %s 0x60 0x20 read-write 0x00000000 OFFSET_EN Offset X Enable 31 1 OFFSET_EN Disabled This bit is written by software to enable or disable the offset programmed into bits OFFSETy[11:0] 0 Enabled This bit is written by software to enable or disable the offset programmed into bits OFFSETy[11:0] 1 OFFSET_CH Channel selection for the data offset X 26 5 0 31 OFFSET Data offset X for the channel programmed into bits OFFSET_CH 0 12 0 4095 4 0x4 1-4 JDR%s JDR%s injected data register %s 0x80 0x20 read-only 0x00000000 JDATA Injected data 0 16 0 65535 AWD2CR AWD2CR Analog Watchdog 2 Configuration Register 0xA0 0x20 read-write 0x00000000 19 0x1 0-18 AWD2CH%s AWD2CH 0 1 AWD2CH0 NotMonitored Input channel not monitored by AWDx 0 Monitored Input channel monitored by AWDx 1 AWD3CR AWD3CR Analog Watchdog 3 Configuration Register 0xA4 0x20 read-write 0x00000000 19 0x1 0-18 AWD3CH%s AWD3CH 0 1 AWD3CH0 NotMonitored Input channel not monitored by AWDx 0 Monitored Input channel monitored by AWDx 1 DIFSEL DIFSEL Differential Mode Selection Register 2 0xB0 0x20 0x00000000 19 0x1 0-18 DIFSEL%s Differential mode for channel %s 0 1 DIFSEL0 SingleEnded Input channel is configured in single-ended mode 0 Differential Input channel is configured in differential mode 1 CALFACT CALFACT Calibration Factors 0xB4 0x20 read-write 0x00000000 CALFACT_D CALFACT_D 16 7 0 127 CALFACT_S CALFACT_S 0 7 0 127 ADC2 0x50040100 ADC1_2 ADC1 and ADC2 global interrupt 18 ADC3 ADC3 global interrupt 47 ADC3 0x50040200 ADC1_2 ADC1 and ADC2 global interrupt 18 ADC3 ADC3 global interrupt 47 ADC_Common Analog-to-Digital Converter ADC_Common 0x50040300 0x0 0x11 registers CSR CSR ADC Common status register 0x0 0x20 read-only 0x00000000 ADRDY_MST ADDRDY_MST 0 1 ADRDY_MST NotReady ADC is not ready to start conversion 0 Ready ADC is ready to start conversion 1 EOSMP_MST EOSMP_MST 1 1 EOSMP_MST NotEnded End of sampling phase no yet reached 0 Ended End of sampling phase reached 1 EOC_MST EOC_MST 2 1 EOC_MST NotComplete Regular conversion is not complete 0 Complete Regular conversion complete 1 EOS_MST EOS_MST 3 1 EOS_MST NotComplete Regular sequence is not complete 0 Complete Regular sequence complete 1 OVR_MST OVR_MST 4 1 OVR_MST NoOverrun No overrun occurred 0 Overrun Overrun occurred 1 JEOC_MST JEOC_MST 5 1 JEOC_MST NotComplete Injected conversion is not complete 0 Complete Injected conversion complete 1 JEOS_MST JEOS_MST 6 1 JEOS_MST NotComplete Injected sequence is not complete 0 Complete Injected sequence complete 1 AWD1_MST AWD1_MST 7 1 AWD1_MST NoEvent No analog watchdog event occurred 0 Event Analog watchdog event occurred 1 AWD2_MST AWD2_MST 8 1 AWD3_MST AWD3_MST 9 1 JQOVF_MST JQOVF_MST 10 1 JQOVF_MST NoOverflow No injected context queue overflow has occurred 0 Overflow Injected context queue overflow has occurred 1 ADRDY_SLV ADRDY_SLV 16 1 EOSMP_SLV EOSMP_SLV 17 1 EOC_SLV End of regular conversion of the slave ADC 18 1 EOS_SLV End of regular sequence flag of the slave ADC 19 1 OVR_SLV Overrun flag of the slave ADC 20 1 JEOC_SLV End of injected conversion flag of the slave ADC 21 1 JEOS_SLV End of injected sequence flag of the slave ADC 22 1 AWD1_SLV Analog watchdog 1 flag of the slave ADC 23 1 AWD2_SLV Analog watchdog 2 flag of the slave ADC 24 1 AWD3_SLV Analog watchdog 3 flag of the slave ADC 25 1 JQOVF_SLV Injected Context Queue Overflow flag of the slave ADC 26 1 CCR CCR ADC common control register 0x8 0x20 read-write 0x00000000 DUAL Dual ADC mode selection 0 5 DUAL Independent Independent mode 0 DualRJ Dual, combined regular simultaneous + injected simultaneous mode 1 DualRA Dual, combined regular simultaneous + alternate trigger mode 2 DualIJ Dual, combined interleaved mode + injected simultaneous mode 3 DualJ Dual, injected simultaneous mode only 5 DualR Dual, regular simultaneous mode only 6 DualI Dual, interleaved mode only 7 DualA Dual, alternate trigger mode only 9 DELAY Delay between 2 sampling phases 8 4 0 15 DMACFG DMA configuration (for multi-ADC mode) 13 1 DMACFG OneShotMode DMA One Shot mode selected 0 CircularMode DMA Circular mode selected 1 MDMA Direct memory access mode for multi ADC mode 14 2 MDMA Disabled MDMA mode disabled 0 Interleaved Enable dual interleaved mode to output to the master channel of DFSDM interface both Master and the Slave result (16-bit data width) 1 Bits12_10 MDMA mode enabled for 12 and 10-bit resolution 2 Bits8_6 MDMA mode enabled for 8 and 6-bit resolution 3 CKMODE ADC clock mode 16 2 CKMODE Asynchronous Use Kernel Clock adc_ker_ck_input divided by PRESC. Asynchronous to AHB clock 0 SyncDiv1 Use AHB clock rcc_hclk3. In this case rcc_hclk must equal sys_d1cpre_ck 1 SyncDiv2 Use AHB clock rcc_hclk3 divided by 2 2 SyncDiv4 Use AHB clock rcc_hclk3 divided by 4 3 VREFEN VREFINT enable 22 1 VREFEN Disabled V_REFINT channel disabled 0 Enabled V_REFINT channel enabled 1 VSENSEEN Temperature sensor selection 23 1 VSENSEEN Disabled The selected ADC channel disabled 0 Enabled The selected ADC channel enabled 1 VBATEN VBAT selection 24 1 PRESC ADC prescaler 18 4 PRESC Div1 Input ADC clock not divided 0 Div2 Input ADC clock divided by 2 1 Div4 Input ADC clock divided by 4 2 Div6 Input ADC clock divided by 6 3 Div8 Input ADC clock divided by 8 4 Div10 Input ADC clock divided by 10 5 Div12 Input ADC clock divided by 12 6 Div16 Input ADC clock divided by 16 7 Div32 Input ADC clock divided by 32 8 Div64 Input ADC clock divided by 64 9 Div128 Input ADC clock divided by 128 10 Div256 Input ADC clock divided by 256 11 CDR CDR ADC common regular data register for dual and triple modes 0xC 0x20 read-only 0x00000000 RDATA_SLV Regular data of the slave ADC 16 16 0 65535 RDATA_MST Regular data of the master ADC 0 16 0 65535 GPIOA General-purpose I/Os GPIO 0x48000000 0x0 0x400 registers MODER MODER GPIO port mode register 0x0 0x20 read-write 0xA8000000 16 0x2 0-15 MODER%s Port x configuration pin %s 0 2 Mode Input Input mode (reset state) 0 Output General purpose output mode 1 Alternate Alternate function mode 2 Analog Analog mode 3 OTYPER OTYPER GPIO port output type register 0x4 0x20 read-write 0x00000000 16 0x1 0-15 OT%s Port x configuration pin %s 0 1 OutputType PushPull Output push-pull (reset state) 0 OpenDrain Output open-drain 1 OSPEEDR OSPEEDR GPIO port output speed register 0x8 0x20 read-write 0x00000000 16 0x2 0-15 OSPEEDR%s Port x configuration pin %s 0 2 OutputSpeed LowSpeed Low speed 0 MediumSpeed Medium speed 1 HighSpeed High speed 2 VeryHighSpeed Very high speed 3 PUPDR PUPDR GPIO port pull-up/pull-down register 0xC 0x20 read-write 0x64000000 16 0x2 0-15 PUPDR%s Port x configuration pin %s 0 2 Pull Floating No pull-up, pull-down 0 PullUp Pull-up 1 PullDown Pull-down 2 IDR IDR GPIO port input data register 0x10 0x20 read-only 0x00000000 16 0x1 0-15 IDR%s Port input data pin %s 0 1 InputData Low Input is logic low 0 High Input is logic high 1 ODR ODR GPIO port output data register 0x14 0x20 read-write 0x00000000 16 0x1 0-15 ODR%s Port output data pin %s 0 1 OutputData Low Set output to logic low 0 High Set output to logic high 1 BSRR BSRR GPIO port bit set/reset register 0x18 0x20 write-only 0x00000000 16 0x1 0-15 BR%s Port x reset pin %s 16 1 BitReset Reset Resets the corresponding ODRx bit 1 16 0x1 0-15 BS%s Port x set pin %s 0 1 BitSet Set Sets the corresponding ODRx bit 1 LCKR LCKR GPIO port configuration lock register 0x1C 0x20 read-write 0x00000000 LCKK Port x lock bit y (y= 0..15) 16 1 LockKey NotActive Port configuration lock key not active 0 Active Port configuration lock key active 1 16 0x1 0-15 LCK%s Port x lock pin %s 0 1 Lock Unlocked Port configuration not locked 0 Locked Port configuration locked 1 AFRL AFRL GPIO alternate function low register 0x20 0x20 read-write 0x00000000 8 0x4 L0,L1,L2,L3,L4,L5,L6,L7 AFR%s Alternate function selection for port x bit y (y = 0..7) 0 4 AlternateFunction AF0 AF0 0 AF1 AF1 1 AF2 AF2 2 AF3 AF3 3 AF4 AF4 4 AF5 AF5 5 AF6 AF6 6 AF7 AF7 7 AF8 AF8 8 AF9 AF9 9 AF10 AF10 10 AF11 AF11 11 AF12 AF12 12 AF13 AF13 13 AF14 AF14 14 AF15 AF15 15 AFRH AFRH GPIO alternate function high register 0x24 0x20 read-write 0x00000000 8 0x4 H8,H9,H10,H11,H12,H13,H14,H15 AFR%s Alternate function selection for port x bit y (y = 8..15) 0 4 BRR BRR GPIO port bit reset register 0x28 0x20 write-only 0x00000000 16 0x1 0-15 BR%s Port x reset pin %s 0 1 BitReset NoAction No action on the corresponding ODx bit 0 Reset Reset the ODx bit 1 ASCR ASCR GPIO port analog switch control register 0x2C 0x20 read-write 0x00000000 ASC0 Port analog switch control 0 1 ASC1 Port analog switch control 1 1 ASC2 Port analog switch control 2 1 ASC3 Port analog switch control 3 1 ASC4 Port analog switch control 4 1 ASC5 Port analog switch control 5 1 ASC6 Port analog switch control 6 1 ASC7 Port analog switch control 7 1 ASC8 Port analog switch control 8 1 ASC9 Port analog switch control 9 1 ASC10 Port analog switch control 10 1 ASC11 Port analog switch control 11 1 ASC12 Port analog switch control 12 1 ASC13 Port analog switch control 13 1 ASC14 Port analog switch control 14 1 ASC15 Port analog switch control 15 1 GPIOB General-purpose I/Os GPIO 0x48000400 0x0 0x400 registers MODER MODER GPIO port mode register 0x0 0x20 read-write 0x00000280 16 0x2 0-15 MODER%s Port x configuration pin %s 0 2 OTYPER OTYPER GPIO port output type register 0x4 OSPEEDR OSPEEDR GPIO port output speed register 0x8 0x20 read-write 0x000000C0 16 0x2 0-15 OSPEEDR%s Port x configuration pin %s 0 2 PUPDR PUPDR GPIO port pull-up/pull-down register 0xC 0x20 read-write 0x00000100 16 0x2 0-15 PUPDR%s Port x configuration pin %s 0 2 IDR IDR GPIO port input data register 0x10 ODR ODR GPIO port output data register 0x14 BSRR BSRR GPIO port bit set/reset register 0x18 LCKR LCKR GPIO port configuration lock register 0x1C AFRL AFRL GPIO alternate function low register 0x20 AFRH AFRH GPIO alternate function high register 0x24 BRR BRR GPIO port bit reset register 0x28 ASCR ASCR GPIO port analog switch control register 0x2C 0x20 read-write 0x00000000 ASC0 Port analog switch control 0 1 ASC1 Port analog switch control 1 1 ASC2 Port analog switch control 2 1 ASC3 Port analog switch control 3 1 ASC4 Port analog switch control 4 1 ASC5 Port analog switch control 5 1 ASC6 Port analog switch control 6 1 ASC7 Port analog switch control 7 1 ASC8 Port analog switch control 8 1 ASC9 Port analog switch control 9 1 ASC10 Port analog switch control 10 1 ASC11 Port analog switch control 11 1 ASC12 Port analog switch control 12 1 ASC13 Port analog switch control 13 1 ASC14 Port analog switch control 14 1 ASC15 Port analog switch control 15 1 GPIOC General-purpose I/Os GPIO 0x48000800 0x0 0x400 registers MODER MODER GPIO port mode register 0x0 0x20 read-write 0x00000000 16 0x2 0-15 MODER%s Port x configuration pin %s 0 2 OTYPER OTYPER GPIO port output type register 0x4 OSPEEDR OSPEEDR GPIO port output speed register 0x8 0x20 read-write 0x00000000 16 0x2 0-15 OSPEEDR%s Port x configuration pin %s 0 2 PUPDR PUPDR GPIO port pull-up/pull-down register 0xC 0x20 read-write 0x00000000 16 0x2 0-15 PUPDR%s Port x configuration pin %s 0 2 IDR IDR GPIO port input data register 0x10 ODR ODR GPIO port output data register 0x14 BSRR BSRR GPIO port bit set/reset register 0x18 LCKR LCKR GPIO port configuration lock register 0x1C AFRL AFRL GPIO alternate function low register 0x20 AFRH AFRH GPIO alternate function high register 0x24 BRR BRR GPIO port bit reset register 0x28 ASCR ASCR GPIO port analog switch control register 0x2C 0x20 read-write 0x00000000 ASC0 Port analog switch control 0 1 ASC1 Port analog switch control 1 1 ASC2 Port analog switch control 2 1 ASC3 Port analog switch control 3 1 ASC4 Port analog switch control 4 1 ASC5 Port analog switch control 5 1 ASC6 Port analog switch control 6 1 ASC7 Port analog switch control 7 1 ASC8 Port analog switch control 8 1 ASC9 Port analog switch control 9 1 ASC10 Port analog switch control 10 1 ASC11 Port analog switch control 11 1 ASC12 Port analog switch control 12 1 ASC13 Port analog switch control 13 1 ASC14 Port analog switch control 14 1 ASC15 Port analog switch control 15 1 GPIOD 0x48000C00 GPIOE 0x48001000 GPIOF 0x48001400 GPIOG 0x48001800 GPIOH 0x48001C00 GPIOI General-purpose I/Os GPIO 0x48002000 0x0 0x400 registers MODER MODER GPIO port mode register 0x0 0x20 read-write 0x00000000 16 0x2 0-15 MODER%s Port x configuration pin %s 0 2 OTYPER OTYPER GPIO port output type register 0x4 OSPEEDR OSPEEDR GPIO port output speed register 0x8 0x20 read-write 0x00000000 16 0x2 0-15 OSPEEDR%s Port x configuration pin %s 0 2 PUPDR PUPDR GPIO port pull-up/pull-down register 0xC 0x20 read-write 0x00000000 16 0x2 0-15 PUPDR%s Port x configuration pin %s 0 2 IDR IDR GPIO port input data register 0x10 ODR ODR GPIO port output data register 0x14 BSRR BSRR GPIO port bit set/reset register 0x18 LCKR LCKR GPIO port configuration lock register 0x1C AFRL AFRL GPIO alternate function low register 0x20 AFRH AFRH GPIO alternate function high register 0x24 BRR BRR GPIO port bit reset register 0x28 SAI1 Serial audio interface SAI 0x40015400 0x0 0x400 registers SAI1 SAI1 global interrupt 74 2 0x20 A,B CH%s Cluster CH%s, containing ?CR1, ?CR2, ?FRCR, ?SLOTR, ?IM, ?SR, ?CLRFR, ?DR 0x4 CR1 ACR1 AConfiguration register 1 0x0 0x20 read-write 0x00000040 MCKDIV Master clock divider 20 4 NODIV No divider 19 1 NODIV MasterClock MCLK output is enabled. Forces the ratio between FS and MCLK to 256 or 512 according to the OSR value 0 NoDiv MCLK output enable set by the MCKEN bit (where present, else 0). Ratio between FS and MCLK depends on FRL. 1 DMAEN DMA enable 17 1 DMAEN Disabled DMA disabled 0 Enabled DMA enabled 1 SAIEN Audio block A enable 16 1 SAIEN Disabled SAI audio block disabled 0 Enabled SAI audio block enabled 1 OUTDRIV Output drive 13 1 OUTDRIV OnStart Audio block output driven when SAIEN is set 0 Immediately Audio block output driven immediately after the setting of this bit 1 MONO Mono mode 12 1 MONO Stereo Stereo mode 0 Mono Mono mode 1 SYNCEN Synchronization enable 10 2 SYNCEN Asynchronous audio sub-block in asynchronous mode 0 Internal audio sub-block is synchronous with the other internal audio sub-block. In this case, the audio sub-block must be configured in slave mode 1 External audio sub-block is synchronous with an external SAI embedded peripheral. In this case the audio sub-block should be configured in Slave mode 2 CKSTR Clock strobing edge 9 1 CKSTR FallingEdge Data strobing edge is falling edge of SCK 0 RisingEdge Data strobing edge is rising edge of SCK 1 LSBFIRST Least significant bit first 8 1 LSBFIRST MsbFirst Data are transferred with MSB first 0 LsbFirst Data are transferred with LSB first 1 DS Data size 5 3 DS Bit8 8 bits 2 Bit10 10 bits 3 Bit16 16 bits 4 Bit20 20 bits 5 Bit24 24 bits 6 Bit32 32 bits 7 PRTCFG Protocol configuration 2 2 PRTCFG Free Free protocol. Free protocol allows to use the powerful configuration of the audio block to address a specific audio protocol 0 Spdif SPDIF protocol 1 Ac97 AC’97 protocol 2 MODE Audio block mode 0 2 MODE MasterTx Master transmitter 0 MasterRx Master receiver 1 SlaveTx Slave transmitter 2 SlaveRx Slave receiver 3 CR2 ACR2 AConfiguration register 2 0x4 0x20 read-write 0x00000000 COMP Companding mode 14 2 read-write COMP NoCompanding No companding algorithm 0 MuLaw μ-Law algorithm 2 ALaw A-Law algorithm 3 CPL Complement bit 13 1 read-write CPL OnesComplement 1’s complement representation 0 TwosComplement 2’s complement representation 1 MUTECNT Mute counter 7 6 read-write MUTEVAL Mute value 6 1 read-write MUTEVAL SendZero Bit value 0 is sent during the mute mode 0 SendLast Last values are sent during the mute mode 1 MUTE Mute 5 1 read-write MUTE Disabled No mute mode 0 Enabled Mute mode enabled 1 TRIS Tristate management on data line 4 1 read-write FFLUSH FIFO flush 3 1 write-only FFLUSH NoFlush No FIFO flush 0 Flush FIFO flush. Programming this bit to 1 triggers the FIFO Flush. All the internal FIFO pointers (read and write) are cleared 1 FTH FIFO threshold 0 3 read-write FTH Empty FIFO empty 0 Quarter1 1⁄4 FIFO 1 Quarter2 1⁄2 FIFO 2 Quarter3 3⁄4 FIFO 3 Full FIFO full 4 FRCR AFRCR AFRCR 0x8 0x20 read-write 0x00000007 FSOFF Frame synchronization offset 18 1 read-write FSOFF OnFirst FS is asserted on the first bit of the slot 0 0 BeforeFirst FS is asserted one bit before the first bit of the slot 0 1 FSPOL Frame synchronization polarity 17 1 read-write FSPOL FallingEdge FS is active low (falling edge) 0 RisingEdge FS is active high (rising edge) 1 FSDEF Frame synchronization definition 16 1 read-write FSALL Frame synchronization active level length 8 7 read-write FRL Frame length 0 8 read-write SLOTR ASLOTR ASlot register 0xC 0x20 read-write 0x00000000 SLOTEN Slot enable 16 16 SLOTEN Inactive Inactive slot 0 Active Active slot 1 NBSLOT Number of slots in an audio frame 8 4 SLOTSZ Slot size 6 2 SLOTSZ DataSize The slot size is equivalent to the data size (specified in DS[3:0] in the SAI_xCR1 register) 0 Bit16 16-bit 1 Bit32 32-bit 2 FBOFF First bit offset 0 5 IM AIM AInterrupt mask register2 0x10 0x20 read-write 0x00000000 LFSDETIE Late frame synchronization detection interrupt enable 6 1 LFSDETIE Disabled Interrupt is disabled 0 Enabled Interrupt is enabled 1 AFSDETIE Anticipated frame synchronization detection interrupt enable 5 1 AFSDETIE Disabled Interrupt is disabled 0 Enabled Interrupt is enabled 1 CNRDYIE Codec not ready interrupt enable 4 1 CNRDYIE Disabled Interrupt is disabled 0 Enabled Interrupt is enabled 1 FREQIE FIFO request interrupt enable 3 1 FREQIE Disabled Interrupt is disabled 0 Enabled Interrupt is enabled 1 WCKCFGIE Wrong clock configuration interrupt enable 2 1 WCKCFGIE Disabled Interrupt is disabled 0 Enabled Interrupt is enabled 1 MUTEDETIE Mute detection interrupt enable 1 1 MUTEDETIE Disabled Interrupt is disabled 0 Enabled Interrupt is enabled 1 OVRUDRIE Overrun/underrun interrupt enable 0 1 OVRUDRIE Disabled Interrupt is disabled 0 Enabled Interrupt is enabled 1 SR ASR AStatus register 0x14 0x20 read-only 0x00000008 FLVL FIFO level threshold 16 3 FLVLR Empty FIFO empty 0 Quarter1 FIFO <= 1⁄4 but not empty 1 Quarter2 1⁄4 < FIFO <= 1⁄2 2 Quarter3 1⁄2 < FIFO <= 3⁄4 3 Quarter4 3⁄4 < FIFO but not full 4 Full FIFO full 5 LFSDET Late frame synchronization detection 6 1 LFSDETR NoError No error 0 NoSync Frame synchronization signal is not present at the right time 1 AFSDET Anticipated frame synchronization detection 5 1 AFSDETR NoError No error 0 EarlySync Frame synchronization signal is detected earlier than expected 1 CNRDY Codec not ready 4 1 CNRDYR Ready External AC’97 Codec is ready 0 NotReady External AC’97 Codec is not ready 1 FREQ FIFO request 3 1 FREQR NoRequest No FIFO request 0 Request FIFO request to read or to write the SAI_xDR 1 WCKCFG Wrong clock configuration flag. This bit is read only 2 1 WCKCFGR Correct Clock configuration is correct 0 Wrong Clock configuration does not respect the rule concerning the frame length specification 1 MUTEDET Mute detection 1 1 MUTEDETR NoMute No MUTE detection on the SD input line 0 Mute MUTE value detected on the SD input line (0 value) for a specified number of consecutive audio frame 1 OVRUDR Overrun / underrun 0 1 OVRUDRR NoError No overrun/underrun error 0 Overrun Overrun/underrun error detection 1 CLRFR ACLRFR AClear flag register 0x18 0x20 write-only 0x00000000 CLFSDET Clear late frame synchronization detection flag 6 1 CLFSDETW Clear Clears the LFSDET flag 1 CAFSDET Clear anticipated frame synchronization detection flag 5 1 CAFSDETW Clear Clears the AFSDET flag 1 CCNRDY Clear codec not ready flag 4 1 CCNRDYW Clear Clears the CNRDY flag 1 CWCKCFG Clear wrong clock configuration flag 2 1 CWCKCFGW Clear Clears the WCKCFG flag 1 CMUTEDET Mute detection flag 1 1 CMUTEDETW Clear Clears the MUTEDET flag 1 COVRUDR Clear overrun / underrun 0 1 COVRUDRW Clear Clears the OVRUDR flag 1 DR ADR AData register 0x1C 0x20 read-write 0x00000000 DATA Data 0 32 SAI2 0x40015800 SAI2 SAI2 global interrupt 75 TIM2 General-purpose-timers TIM 0x40000000 0x0 0x400 registers TIM2 TIM2 global interrupt 28 CR1 CR1 control register 1 0x0 0x10 read-write 0x00000000 UIFREMAP UIF status bit remapping 11 1 CKD Clock division 8 2 CKD Div1 t_DTS = t_CK_INT 0 Div2 t_DTS = 2 × t_CK_INT 1 Div4 t_DTS = 4 × t_CK_INT 2 ARPE Auto-reload preload enable 7 1 ARPE Disabled TIMx_APRR register is not buffered 0 Enabled TIMx_APRR register is buffered 1 CMS Center-aligned mode selection 5 2 CMS EdgeAligned The counter counts up or down depending on the direction bit 0 CenterAligned1 The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting down. 1 CenterAligned2 The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting up. 2 CenterAligned3 The counter counts up and down alternatively. Output compare interrupt flags are set both when the counter is counting up or down. 3 DIR Direction 4 1 DIR Up Counter used as upcounter 0 Down Counter used as downcounter 1 OPM One-pulse mode 3 1 OPM Disabled Counter is not stopped at update event 0 Enabled Counter stops counting at the next update event (clearing the CEN bit) 1 URS Update request source 2 1 URS AnyEvent Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request 0 CounterOnly Only counter overflow/underflow generates an update interrupt or DMA request 1 UDIS Update disable 1 1 UDIS Enabled Update event enabled 0 Disabled Update event disabled 1 CEN Counter enable 0 1 CEN Disabled Counter disabled 0 Enabled Counter enabled 1 CR2 CR2 control register 2 0x4 0x10 read-write 0x00000000 TI1S TI1 selection 7 1 TI1S Normal The TIMx_CH1 pin is connected to TI1 input 0 XOR The TIMx_CH1, CH2, CH3 pins are connected to TI1 input 1 MMS Master mode selection 4 3 MMS Reset The UG bit from the TIMx_EGR register is used as trigger output 0 Enable The counter enable signal, CNT_EN, is used as trigger output 1 Update The update event is selected as trigger output 2 ComparePulse The trigger output send a positive pulse when the CC1IF flag it to be set, as soon as a capture or a compare match occurred 3 CompareOC1 OC1REF signal is used as trigger output 4 CompareOC2 OC2REF signal is used as trigger output 5 CompareOC3 OC3REF signal is used as trigger output 6 CompareOC4 OC4REF signal is used as trigger output 7 CCDS Capture/compare DMA selection 3 1 CCDS OnCompare CCx DMA request sent when CCx event occurs 0 OnUpdate CCx DMA request sent when update event occurs 1 SMCR SMCR slave mode control register 0x8 0x20 read-write 0x00000000 SMS_3 Slave mode selection - bit 3 16 1 ETP External trigger polarity 15 1 ETP NotInverted ETR is noninverted, active at high level or rising edge 0 Inverted ETR is inverted, active at low level or falling edge 1 ECE External clock enable 14 1 ECE Disabled External clock mode 2 disabled 0 Enabled External clock mode 2 enabled. The counter is clocked by any active edge on the ETRF signal. 1 ETPS External trigger prescaler 12 2 ETPS Div1 Prescaler OFF 0 Div2 ETRP frequency divided by 2 1 Div4 ETRP frequency divided by 4 2 Div8 ETRP frequency divided by 8 3 ETF External trigger filter 8 4 ETF NoFilter No filter, sampling is done at fDTS 0 FCK_INT_N2 fSAMPLING=fCK_INT, N=2 1 FCK_INT_N4 fSAMPLING=fCK_INT, N=4 2 FCK_INT_N8 fSAMPLING=fCK_INT, N=8 3 FDTS_Div2_N6 fSAMPLING=fDTS/2, N=6 4 FDTS_Div2_N8 fSAMPLING=fDTS/2, N=8 5 FDTS_Div4_N6 fSAMPLING=fDTS/4, N=6 6 FDTS_Div4_N8 fSAMPLING=fDTS/4, N=8 7 FDTS_Div8_N6 fSAMPLING=fDTS/8, N=6 8 FDTS_Div8_N8 fSAMPLING=fDTS/8, N=8 9 FDTS_Div16_N5 fSAMPLING=fDTS/16, N=5 10 FDTS_Div16_N6 fSAMPLING=fDTS/16, N=6 11 FDTS_Div16_N8 fSAMPLING=fDTS/16, N=8 12 FDTS_Div32_N5 fSAMPLING=fDTS/32, N=5 13 FDTS_Div32_N6 fSAMPLING=fDTS/32, N=6 14 FDTS_Div32_N8 fSAMPLING=fDTS/32, N=8 15 MSM Master/Slave mode 7 1 MSM NoSync No action 0 Sync The effect of an event on the trigger input (TRGI) is delayed to allow a perfect synchronization between the current timer and its slaves (through TRGO). It is useful if we want to synchronize several timers on a single external event. 1 TS Trigger selection 4 3 TS ITR0 Internal Trigger 0 (ITR0) 0 ITR1 Internal Trigger 1 (ITR1) 1 ITR2 Internal Trigger 2 (ITR2) 2 TI1F_ED TI1 Edge Detector (TI1F_ED) 4 TI1FP1 Filtered Timer Input 1 (TI1FP1) 5 TI2FP2 Filtered Timer Input 2 (TI2FP2) 6 ETRF External Trigger input (ETRF) 7 OCCS OCREF clear selection 3 1 SMS Slave mode selection 0 3 SMS Disabled Slave mode disabled - if CEN = ‘1 then the prescaler is clocked directly by the internal clock. 0 Encoder_Mode_1 Encoder mode 1 - Counter counts up/down on TI2FP1 edge depending on TI1FP2 level. 1 Encoder_Mode_2 Encoder mode 2 - Counter counts up/down on TI1FP2 edge depending on TI2FP1 level. 2 Encoder_Mode_3 Encoder mode 3 - Counter counts up/down on both TI1FP1 and TI2FP2 edges depending on the level of the other input. 3 Reset_Mode Reset Mode - Rising edge of the selected trigger input (TRGI) reinitializes the counter and generates an update of the registers. 4 Gated_Mode Gated Mode - The counter clock is enabled when the trigger input (TRGI) is high. The counter stops (but is not reset) as soon as the trigger becomes low. Both start and stop of the counter are controlled. 5 Trigger_Mode Trigger Mode - The counter starts at a rising edge of the trigger TRGI (but it is not reset). Only the start of the counter is controlled. 6 Ext_Clock_Mode External Clock Mode 1 - Rising edges of the selected trigger (TRGI) clock the counter. 7 DIER DIER DMA/Interrupt enable register 0xC 0x10 read-write 0x00000000 TDE Trigger DMA request enable 14 1 TDE Disabled Trigger DMA request disabled 0 Enabled Trigger DMA request enabled 1 4 0x1 1-4 CC%sDE Capture/Compare %s DMA request enable 9 1 CC1DE Disabled CCx DMA request disabled 0 Enabled CCx DMA request enabled 1 UDE Update DMA request enable 8 1 UDE Disabled Update DMA request disabled 0 Enabled Update DMA request enabled 1 TIE Trigger interrupt enable 6 1 TIE Disabled Trigger interrupt disabled 0 Enabled Trigger interrupt enabled 1 4 0x1 1-4 CC%sIE Capture/Compare %s interrupt enable 1 1 CC1IE Disabled CCx interrupt disabled 0 Enabled CCx interrupt enabled 1 UIE Update interrupt enable 0 1 UIE Disabled Update interrupt disabled 0 Enabled Update interrupt enabled 1 SR SR status register 0x10 0x10 read-write 0x00000000 4 0x1 1-4 CC%sOF Capture/Compare %s overcapture flag 9 1 zeroToClear CC1OFR read NoOvercapture No overcapture has been detected 0 Overcapture The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set 1 CC1OFW write Clear Clear flag 0 TIF Trigger interrupt flag 6 1 zeroToClear TIFR read NoTrigger No trigger event occurred 0 Trigger Trigger interrupt pending 1 TIFW write Clear Clear flag 0 4 0x1 1-4 CC%sIF Capture/compare %s interrupt flag 1 1 zeroToClear CC1IFR read NoMatch No campture/compare has been detected 0 Match If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register. 1 CC1IFW write Clear Clear flag 0 UIF Update interrupt flag 0 1 zeroToClear UIFR read NoUpdateOccurred No update occurred 0 UpdatePending Update interrupt pending 1 UIFW write Clear Clear flag 0 EGR EGR event generation register 0x14 0x10 write-only 0x00000000 TG Trigger generation 6 1 TGW Trigger The TIF flag is set in TIMx_SR register. Related interrupt or DMA transfer can occur if enabled. 1 4 0x1 1-4 CC%sG Capture/compare %s generation 1 1 CC1GW Trigger If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register. 1 UG Update generation 0 1 UG Update Re-initializes the timer counter and generates an update of the registers. 1 CCMR1_Output CCMR1_Output capture/compare mode register 1 (output mode) 0x18 0x20 read-write 0x00000000 2 0x8 1-2 OC%sM_3 Output compare %s mode, bit 3 16 1 OC1M_3 Normal Normal output compare mode (modes 0-7) 0 Extended Extended output compare mode (modes 7-15) 1 2 0x8 1-2 OC%sCE Output compare %s clear enable 7 1 OC1CE Disabled OCxRef is not affected by the ETRF signal 0 Enabled OCxRef is cleared as soon as a High level is detected on ETRF signal 1 2 0x8 1-2 OC%sM Output compare %s mode 4 3 OC1M Frozen The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive 0 ActiveOnMatch Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1 1 InactiveOnMatch Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved 2 Toggle OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved 3 ForceInactive OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF 4 ForceActive OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF 5 PwmMode1 In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down 6 PwmMode2 Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1 7 2 0x8 1-2 OC%sPE Output compare %s preload enable 3 1 OC1PE Disabled Preload register on CCRx disabled. New values written to CCRx are taken into account immediately 0 Enabled Preload register on CCRx enabled. Preload value is loaded into active register on each update event 1 2 0x8 1-2 OC%sFE Output compare %s fast enable 2 1 OC1FE Disabled Fast output disabled 0 Enabled Fast output enabled 1 2 0x8 1-2 CC%sS Capture/Compare %s selection 0 2 CC1S Output CCx channel is configured as output 0 CCMR1_Input CCMR1_Input capture/compare mode register 1 (input mode) CCMR1_Output 0x18 0x20 read-write 0x00000000 2 0x8 1-2 IC%sF Input capture %s filter 4 4 ICFilter NoFilter No filter, sampling is done at fDTS 0 FCK_INT_N2 fSAMPLING=fCK_INT, N=2 1 FCK_INT_N4 fSAMPLING=fCK_INT, N=4 2 FCK_INT_N8 fSAMPLING=fCK_INT, N=8 3 FDTS_Div2_N6 fSAMPLING=fDTS/2, N=6 4 FDTS_Div2_N8 fSAMPLING=fDTS/2, N=8 5 FDTS_Div4_N6 fSAMPLING=fDTS/4, N=6 6 FDTS_Div4_N8 fSAMPLING=fDTS/4, N=8 7 FDTS_Div8_N6 fSAMPLING=fDTS/8, N=6 8 FDTS_Div8_N8 fSAMPLING=fDTS/8, N=8 9 FDTS_Div16_N5 fSAMPLING=fDTS/16, N=5 10 FDTS_Div16_N6 fSAMPLING=fDTS/16, N=6 11 FDTS_Div16_N8 fSAMPLING=fDTS/16, N=8 12 FDTS_Div32_N5 fSAMPLING=fDTS/32, N=5 13 FDTS_Div32_N6 fSAMPLING=fDTS/32, N=6 14 FDTS_Div32_N8 fSAMPLING=fDTS/32, N=8 15 2 0x8 1-2 IC%sPSC Input capture %s prescaler 2 2 ICPrescaler NoPrescaler No prescaler, capture is done each time an edge is detected on the capture input 0 TwoEvents Capture is done once every 2 events 1 FourEvents Capture is done once every 4 events 2 EightEvents Capture is done once every 8 events 3 CC2S Capture/compare 2 selection 8 2 CC2S TI2 CC2 channel is configured as input, IC2 is mapped on TI2 1 TI1 CC2 channel is configured as input, IC2 is mapped on TI1 2 TRC CC2 channel is configured as input, IC2 is mapped on TRC 3 CC1S Capture/Compare 1 selection 0 2 CC1S TI1 CC1 channel is configured as input, IC1 is mapped on TI1 1 TI2 CC1 channel is configured as input, IC1 is mapped on TI2 2 TRC CC1 channel is configured as input, IC1 is mapped on TRC 3 CCMR2_Output CCMR2_Output capture/compare mode register 2 (output mode) 0x1C 0x20 read-write 0x00000000 2 0x8 3-4 OC%sM_3 Output compare %s mode, bit 3 16 1 2 0x8 3-4 OC%sCE Output compare %s clear enable 7 1 2 0x8 3-4 OC%sM Output compare %s mode 4 3 2 0x8 3-4 OC%sPE Output compare %s preload enable 3 1 2 0x8 3-4 OC%sFE Output compare %s fast enable 2 1 2 0x8 3-4 CC%sS Capture/Compare %s selection 0 2 CCMR2_Input CCMR2_Input capture/compare mode register 2 (input mode) CCMR2_Output 0x1C 0x20 read-write 0x00000000 2 0x8 3-4 IC%sF Input capture %s filter 4 4 2 0x8 3-4 IC%sPSC Input capture %s prescaler 2 2 CC4S Capture/Compare 4 selection 8 2 CC4S TI4 CC4 channel is configured as input, IC4 is mapped on TI4 1 TI3 CC4 channel is configured as input, IC4 is mapped on TI3 2 TRC CC4 channel is configured as input, IC4 is mapped on TRC 3 CC3S Capture/Compare 3 selection 0 2 CC3S TI3 CC3 channel is configured as input, IC3 is mapped on TI3 1 TI4 CC3 channel is configured as input, IC3 is mapped on TI4 2 TRC CC3 channel is configured as input, IC3 is mapped on TRC 3 CCER CCER capture/compare enable register 0x20 0x10 read-write 0x00000000 4 0x4 1-4 CC%sNP Capture/Compare %s output Polarity 3 1 4 0x4 1-4 CC%sP Capture/Compare %s output Polarity 1 1 CC1P RisingEdge Noninverted/rising edge 0 FallingEdge Inverted/falling edge 1 4 0x4 1-4 CC%sE Capture/Compare %s output enable 0 1 CC1E Disabled Capture disabled 0 Enabled Capture enabled 1 CNT CNT counter 0x24 0x20 read-write 0x00000000 CNT Counter value 0 32 CNT32 CNT32 32-bit counter register CNT 0x24 0x20 read-write 0x00000000 CNT counter value 0 32 read-write 0 4294967295 PSC PSC prescaler 0x28 0x10 read-write 0x00000000 PSC Prescaler value 0 16 0 65535 ARR ARR auto-reload register 0x2C 0x20 read-write 0xFFFFFFFF ARR Auto-reload value 0 32 0 4294967295 4 0x4 1-4 CCR%s CCR%s capture/compare register 0x34 0x20 read-write 0x00000000 CCR Capture/Compare value 0 32 0 4294967295 DCR DCR DMA control register 0x48 0x10 read-write 0x00000000 DBL DMA burst length 8 5 0 18 DBA DMA base address 0 5 0 31 DMAR DMAR DMA address for full transfer 0x4C 0x10 read-write 0x00000000 DMAB DMA register for burst accesses 0 16 OR1 OR1 TIM2 option register 1 0x50 0x20 read-write 0x00000000 ITR1_RMP Internal trigger 1 remap 0 1 ETR1_RMP External trigger remap 1 1 TI4_RMP Input Capture 4 remap 2 2 OR2 OR2 TIM2 option register 2 0x60 0x20 read-write 0x00000000 ETRSEL ETR source selection 14 3 TIM3 General-purpose-timers TIM 0x40000400 0x0 0x400 registers TIM3 TIM3 global interrupt 29 CR1 CR1 control register 1 0x0 0x10 read-write 0x00000000 UIFREMAP UIF status bit remapping 11 1 CKD Clock division 8 2 CKD Div1 t_DTS = t_CK_INT 0 Div2 t_DTS = 2 × t_CK_INT 1 Div4 t_DTS = 4 × t_CK_INT 2 ARPE Auto-reload preload enable 7 1 ARPE Disabled TIMx_APRR register is not buffered 0 Enabled TIMx_APRR register is buffered 1 CMS Center-aligned mode selection 5 2 CMS EdgeAligned The counter counts up or down depending on the direction bit 0 CenterAligned1 The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting down. 1 CenterAligned2 The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting up. 2 CenterAligned3 The counter counts up and down alternatively. Output compare interrupt flags are set both when the counter is counting up or down. 3 DIR Direction 4 1 DIR Up Counter used as upcounter 0 Down Counter used as downcounter 1 OPM One-pulse mode 3 1 OPM Disabled Counter is not stopped at update event 0 Enabled Counter stops counting at the next update event (clearing the CEN bit) 1 URS Update request source 2 1 URS AnyEvent Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request 0 CounterOnly Only counter overflow/underflow generates an update interrupt or DMA request 1 UDIS Update disable 1 1 UDIS Enabled Update event enabled 0 Disabled Update event disabled 1 CEN Counter enable 0 1 CEN Disabled Counter disabled 0 Enabled Counter enabled 1 CR2 CR2 control register 2 0x4 0x10 read-write 0x00000000 TI1S TI1 selection 7 1 TI1S Normal The TIMx_CH1 pin is connected to TI1 input 0 XOR The TIMx_CH1, CH2, CH3 pins are connected to TI1 input 1 MMS Master mode selection 4 3 MMS Reset The UG bit from the TIMx_EGR register is used as trigger output 0 Enable The counter enable signal, CNT_EN, is used as trigger output 1 Update The update event is selected as trigger output 2 ComparePulse The trigger output send a positive pulse when the CC1IF flag it to be set, as soon as a capture or a compare match occurred 3 CompareOC1 OC1REF signal is used as trigger output 4 CompareOC2 OC2REF signal is used as trigger output 5 CompareOC3 OC3REF signal is used as trigger output 6 CompareOC4 OC4REF signal is used as trigger output 7 CCDS Capture/compare DMA selection 3 1 CCDS OnCompare CCx DMA request sent when CCx event occurs 0 OnUpdate CCx DMA request sent when update event occurs 1 SMCR SMCR slave mode control register 0x8 0x20 read-write 0x00000000 SMS_3 Slave mode selection - bit 3 16 1 ETP External trigger polarity 15 1 ETP NotInverted ETR is noninverted, active at high level or rising edge 0 Inverted ETR is inverted, active at low level or falling edge 1 ECE External clock enable 14 1 ECE Disabled External clock mode 2 disabled 0 Enabled External clock mode 2 enabled. The counter is clocked by any active edge on the ETRF signal. 1 ETPS External trigger prescaler 12 2 ETPS Div1 Prescaler OFF 0 Div2 ETRP frequency divided by 2 1 Div4 ETRP frequency divided by 4 2 Div8 ETRP frequency divided by 8 3 ETF External trigger filter 8 4 ETF NoFilter No filter, sampling is done at fDTS 0 FCK_INT_N2 fSAMPLING=fCK_INT, N=2 1 FCK_INT_N4 fSAMPLING=fCK_INT, N=4 2 FCK_INT_N8 fSAMPLING=fCK_INT, N=8 3 FDTS_Div2_N6 fSAMPLING=fDTS/2, N=6 4 FDTS_Div2_N8 fSAMPLING=fDTS/2, N=8 5 FDTS_Div4_N6 fSAMPLING=fDTS/4, N=6 6 FDTS_Div4_N8 fSAMPLING=fDTS/4, N=8 7 FDTS_Div8_N6 fSAMPLING=fDTS/8, N=6 8 FDTS_Div8_N8 fSAMPLING=fDTS/8, N=8 9 FDTS_Div16_N5 fSAMPLING=fDTS/16, N=5 10 FDTS_Div16_N6 fSAMPLING=fDTS/16, N=6 11 FDTS_Div16_N8 fSAMPLING=fDTS/16, N=8 12 FDTS_Div32_N5 fSAMPLING=fDTS/32, N=5 13 FDTS_Div32_N6 fSAMPLING=fDTS/32, N=6 14 FDTS_Div32_N8 fSAMPLING=fDTS/32, N=8 15 MSM Master/Slave mode 7 1 MSM NoSync No action 0 Sync The effect of an event on the trigger input (TRGI) is delayed to allow a perfect synchronization between the current timer and its slaves (through TRGO). It is useful if we want to synchronize several timers on a single external event. 1 TS Trigger selection 4 3 TS ITR0 Internal Trigger 0 (ITR0) 0 ITR1 Internal Trigger 1 (ITR1) 1 ITR2 Internal Trigger 2 (ITR2) 2 TI1F_ED TI1 Edge Detector (TI1F_ED) 4 TI1FP1 Filtered Timer Input 1 (TI1FP1) 5 TI2FP2 Filtered Timer Input 2 (TI2FP2) 6 ETRF External Trigger input (ETRF) 7 OCCS OCREF clear selection 3 1 SMS Slave mode selection 0 3 SMS Disabled Slave mode disabled - if CEN = ‘1 then the prescaler is clocked directly by the internal clock. 0 Encoder_Mode_1 Encoder mode 1 - Counter counts up/down on TI2FP1 edge depending on TI1FP2 level. 1 Encoder_Mode_2 Encoder mode 2 - Counter counts up/down on TI1FP2 edge depending on TI2FP1 level. 2 Encoder_Mode_3 Encoder mode 3 - Counter counts up/down on both TI1FP1 and TI2FP2 edges depending on the level of the other input. 3 Reset_Mode Reset Mode - Rising edge of the selected trigger input (TRGI) reinitializes the counter and generates an update of the registers. 4 Gated_Mode Gated Mode - The counter clock is enabled when the trigger input (TRGI) is high. The counter stops (but is not reset) as soon as the trigger becomes low. Both start and stop of the counter are controlled. 5 Trigger_Mode Trigger Mode - The counter starts at a rising edge of the trigger TRGI (but it is not reset). Only the start of the counter is controlled. 6 Ext_Clock_Mode External Clock Mode 1 - Rising edges of the selected trigger (TRGI) clock the counter. 7 DIER DIER DMA/Interrupt enable register 0xC 0x10 read-write 0x00000000 TDE Trigger DMA request enable 14 1 TDE Disabled Trigger DMA request disabled 0 Enabled Trigger DMA request enabled 1 4 0x1 1-4 CC%sDE Capture/Compare %s DMA request enable 9 1 CC1DE Disabled CCx DMA request disabled 0 Enabled CCx DMA request enabled 1 UDE Update DMA request enable 8 1 UDE Disabled Update DMA request disabled 0 Enabled Update DMA request enabled 1 TIE Trigger interrupt enable 6 1 TIE Disabled Trigger interrupt disabled 0 Enabled Trigger interrupt enabled 1 4 0x1 1-4 CC%sIE Capture/Compare %s interrupt enable 1 1 CC1IE Disabled CCx interrupt disabled 0 Enabled CCx interrupt enabled 1 UIE Update interrupt enable 0 1 UIE Disabled Update interrupt disabled 0 Enabled Update interrupt enabled 1 SR SR status register 0x10 0x10 read-write 0x00000000 4 0x1 1-4 CC%sOF Capture/Compare %s overcapture flag 9 1 zeroToClear CC1OFR read NoOvercapture No overcapture has been detected 0 Overcapture The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set 1 CC1OFW write Clear Clear flag 0 TIF Trigger interrupt flag 6 1 zeroToClear TIFR read NoTrigger No trigger event occurred 0 Trigger Trigger interrupt pending 1 TIFW write Clear Clear flag 0 4 0x1 1-4 CC%sIF Capture/compare %s interrupt flag 1 1 zeroToClear CC1IFR read NoMatch No campture/compare has been detected 0 Match If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register. 1 CC1IFW write Clear Clear flag 0 UIF Update interrupt flag 0 1 zeroToClear UIFR read NoUpdateOccurred No update occurred 0 UpdatePending Update interrupt pending 1 UIFW write Clear Clear flag 0 EGR EGR event generation register 0x14 0x10 write-only 0x00000000 TG Trigger generation 6 1 TGW Trigger The TIF flag is set in TIMx_SR register. Related interrupt or DMA transfer can occur if enabled. 1 4 0x1 1-4 CC%sG Capture/compare %s generation 1 1 CC1GW Trigger If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register. 1 UG Update generation 0 1 UG Update Re-initializes the timer counter and generates an update of the registers. 1 CCMR1_Output CCMR1_Output capture/compare mode register 1 (output mode) 0x18 0x20 read-write 0x00000000 2 0x8 1-2 OC%sM_3 Output compare %s mode, bit 3 16 1 OC1M_3 Normal Normal output compare mode (modes 0-7) 0 Extended Extended output compare mode (modes 7-15) 1 2 0x8 1-2 OC%sCE Output compare %s clear enable 7 1 OC1CE Disabled OCxRef is not affected by the ETRF signal 0 Enabled OCxRef is cleared as soon as a High level is detected on ETRF signal 1 2 0x8 1-2 OC%sM Output compare %s mode 4 3 OC1M Frozen The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive 0 ActiveOnMatch Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1 1 InactiveOnMatch Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved 2 Toggle OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved 3 ForceInactive OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF 4 ForceActive OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF 5 PwmMode1 In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down 6 PwmMode2 Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1 7 2 0x8 1-2 OC%sPE Output compare %s preload enable 3 1 OC1PE Disabled Preload register on CCRx disabled. New values written to CCRx are taken into account immediately 0 Enabled Preload register on CCRx enabled. Preload value is loaded into active register on each update event 1 2 0x8 1-2 OC%sFE Output compare %s fast enable 2 1 OC1FE Disabled Fast output disabled 0 Enabled Fast output enabled 1 2 0x8 1-2 CC%sS Capture/Compare %s selection 0 2 CC1S Output CCx channel is configured as output 0 CCMR1_Input CCMR1_Input capture/compare mode register 1 (input mode) CCMR1_Output 0x18 0x20 read-write 0x00000000 2 0x8 1-2 IC%sF Input capture %s filter 4 4 ICFilter NoFilter No filter, sampling is done at fDTS 0 FCK_INT_N2 fSAMPLING=fCK_INT, N=2 1 FCK_INT_N4 fSAMPLING=fCK_INT, N=4 2 FCK_INT_N8 fSAMPLING=fCK_INT, N=8 3 FDTS_Div2_N6 fSAMPLING=fDTS/2, N=6 4 FDTS_Div2_N8 fSAMPLING=fDTS/2, N=8 5 FDTS_Div4_N6 fSAMPLING=fDTS/4, N=6 6 FDTS_Div4_N8 fSAMPLING=fDTS/4, N=8 7 FDTS_Div8_N6 fSAMPLING=fDTS/8, N=6 8 FDTS_Div8_N8 fSAMPLING=fDTS/8, N=8 9 FDTS_Div16_N5 fSAMPLING=fDTS/16, N=5 10 FDTS_Div16_N6 fSAMPLING=fDTS/16, N=6 11 FDTS_Div16_N8 fSAMPLING=fDTS/16, N=8 12 FDTS_Div32_N5 fSAMPLING=fDTS/32, N=5 13 FDTS_Div32_N6 fSAMPLING=fDTS/32, N=6 14 FDTS_Div32_N8 fSAMPLING=fDTS/32, N=8 15 2 0x8 1-2 IC%sPSC Input capture %s prescaler 2 2 ICPrescaler NoPrescaler No prescaler, capture is done each time an edge is detected on the capture input 0 TwoEvents Capture is done once every 2 events 1 FourEvents Capture is done once every 4 events 2 EightEvents Capture is done once every 8 events 3 CC2S Capture/compare 2 selection 8 2 CC2S TI2 CC2 channel is configured as input, IC2 is mapped on TI2 1 TI1 CC2 channel is configured as input, IC2 is mapped on TI1 2 TRC CC2 channel is configured as input, IC2 is mapped on TRC 3 CC1S Capture/Compare 1 selection 0 2 CC1S TI1 CC1 channel is configured as input, IC1 is mapped on TI1 1 TI2 CC1 channel is configured as input, IC1 is mapped on TI2 2 TRC CC1 channel is configured as input, IC1 is mapped on TRC 3 CCMR2_Output CCMR2_Output capture/compare mode register 2 (output mode) 0x1C 0x20 read-write 0x00000000 2 0x8 3-4 OC%sM_3 Output compare %s mode, bit 3 16 1 2 0x8 3-4 OC%sCE Output compare %s clear enable 7 1 2 0x8 3-4 OC%sM Output compare %s mode 4 3 2 0x8 3-4 OC%sPE Output compare %s preload enable 3 1 2 0x8 3-4 OC%sFE Output compare %s fast enable 2 1 2 0x8 3-4 CC%sS Capture/Compare %s selection 0 2 CCMR2_Input CCMR2_Input capture/compare mode register 2 (input mode) CCMR2_Output 0x1C 0x20 read-write 0x00000000 2 0x8 3-4 IC%sF Input capture %s filter 4 4 2 0x8 3-4 IC%sPSC Input capture %s prescaler 2 2 CC4S Capture/Compare 4 selection 8 2 CC4S TI4 CC4 channel is configured as input, IC4 is mapped on TI4 1 TI3 CC4 channel is configured as input, IC4 is mapped on TI3 2 TRC CC4 channel is configured as input, IC4 is mapped on TRC 3 CC3S Capture/Compare 3 selection 0 2 CC3S TI3 CC3 channel is configured as input, IC3 is mapped on TI3 1 TI4 CC3 channel is configured as input, IC3 is mapped on TI4 2 TRC CC3 channel is configured as input, IC3 is mapped on TRC 3 CCER CCER capture/compare enable register 0x20 0x10 read-write 0x00000000 4 0x4 1-4 CC%sNP Capture/Compare %s output Polarity 3 1 4 0x4 1-4 CC%sP Capture/Compare %s output Polarity 1 1 CC1P RisingEdge Noninverted/rising edge 0 FallingEdge Inverted/falling edge 1 4 0x4 1-4 CC%sE Capture/Compare %s output enable 0 1 CC1E Disabled Capture disabled 0 Enabled Capture enabled 1 CNT CNT counter 0x24 0x20 read-write 0x00000000 CNT Counter value 0 16 0 65535 CNT16 CNT16 16-bit counter register CNT 0x24 0x10 read-write 0x00000000 CNT counter value 0 16 read-write 0 65535 PSC PSC prescaler 0x28 0x10 read-write 0x00000000 PSC Prescaler value 0 16 0 65535 ARR ARR auto-reload register 0x2C 0x10 read-write 0x0000FFFF ARR Auto-reload value 0 16 0 65535 4 0x4 1-4 CCR%s CCR%s capture/compare register 0x34 0x10 read-write 0x00000000 CCR Capture/Compare value 0 16 0 65535 DCR DCR DMA control register 0x48 0x10 read-write 0x00000000 DBL DMA burst length 8 5 0 18 DBA DMA base address 0 5 0 31 DMAR DMAR DMA address for full transfer 0x4C 0x10 read-write 0x00000000 DMAB DMA register for burst accesses 0 16 OR1 OR1 TIM2 option register 1 0x50 0x20 read-write 0x00000000 ITR1_RMP Internal trigger 1 remap 0 1 ETR1_RMP External trigger remap 1 1 TI4_RMP Input Capture 4 remap 2 2 OR2 OR2 TIM2 option register 2 0x60 0x20 read-write 0x00000000 ETRSEL ETR source selection 14 3 TIM4 TIM 0x40000800 TIM4 TIM4 global interrupt 30 TIM5 TIM 0x40000C00 TIM5 TIM5 global Interrupt 50 TIM15 General purpose timers TIM 0x40014000 0x0 0x400 registers CR1 CR1 control register 1 0x0 0x10 read-write 0x00000000 CEN Counter enable 0 1 CEN Disabled Counter disabled 0 Enabled Counter enabled 1 UDIS Update disable 1 1 UDIS Enabled Update event enabled 0 Disabled Update event disabled 1 URS Update request source 2 1 URS AnyEvent Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request 0 CounterOnly Only counter overflow/underflow generates an update interrupt or DMA request 1 OPM One-pulse mode 3 1 OPM Disabled Counter is not stopped at update event 0 Enabled Counter stops counting at the next update event (clearing the CEN bit) 1 ARPE Auto-reload preload enable 7 1 ARPE Disabled TIMx_APRR register is not buffered 0 Enabled TIMx_APRR register is buffered 1 CKD Clock division 8 2 CKD Div1 t_DTS = t_CK_INT 0 Div2 t_DTS = 2 × t_CK_INT 1 Div4 t_DTS = 4 × t_CK_INT 2 UIFREMAP UIF status bit remapping 11 1 CR2 CR2 control register 2 0x4 0x10 read-write 0x00000000 2 0x2 1-2 OIS%s Output Idle state (OC%s output) 8 1 OIS1 Reset OCx=0 (after a dead-time if OCx(N) is implemented) when MOE=0 0 Set OCx=1 (after a dead-time if OCx(N) is implemented) when MOE=0 1 1 0x0 1-1 OIS%sN Output Idle state (OC%sN output) 9 1 OIS1N Reset OCxN=0 after a dead-time when MOE=0 0 Set OCxN=1 after a dead-time when MOE=0 1 TI1S TI1 selection 7 1 MMS Master mode selection 4 3 CCDS Capture/compare DMA selection 3 1 CCDS OnCompare CCx DMA request sent when CCx event occurs 0 OnUpdate CCx DMA request sent when update event occurs 1 CCUS Capture/compare control update selection 2 1 CCUS Sw When capture/compare control bits are preloaded (CCPC=1), they are updated by setting the COMG bit only 0 SwOrEdge When capture/compare control bits are preloaded (CCPC=1), they are updated by setting the COMG bit or when an rising edge occurs on TRGI 1 CCPC Capture/compare preloaded control 0 1 CCPC NotPreloaded CCxE, CCxNE and OCxM bits are not preloaded 0 Preloaded CCxE, CCxNE and OCxM bits are preloaded 1 SMCR SMCR slave mode control register 0x8 0x20 read-write 0x00000000 SMS Slave mode selection 0 3 TS Trigger selection 4 3 MSM Master/slave mode 7 1 SMS_3 Slave mode selection - bit 3 16 1 DIER DIER DMA/Interrupt enable register 0xC 0x10 read-write 0x00000000 TDE Trigger DMA request enable 14 1 TDE Disabled Trigger DMA request disabled 0 Enabled Trigger DMA request enabled 1 COMDE COM DMA request enable 13 1 COMDE Disabled COM DMA request disabled 0 Enabled COM DMA request enabled 1 2 0x1 1-2 CC%sDE Capture/Compare %s DMA request enable 9 1 CC1DE Disabled CCx DMA request disabled 0 Enabled CCx DMA request enabled 1 UDE Update DMA request enable 8 1 UDE Disabled Update DMA request disabled 0 Enabled Update DMA request enabled 1 BIE Break interrupt enable 7 1 BIE Disabled Break interrupt disabled 0 Enabled Break interrupt enabled 1 TIE Trigger interrupt enable 6 1 TIE Disabled Trigger interrupt disabled 0 Enabled Trigger interrupt enabled 1 COMIE COM interrupt enable 5 1 COMIE Disabled COM interrupt disabled 0 Enabled COM interrupt enabled 1 2 0x1 1-2 CC%sIE Capture/Compare %s interrupt enable 1 1 CC1IE Disabled CCx interrupt disabled 0 Enabled CCx interrupt enabled 1 UIE Update interrupt enable 0 1 UIE Disabled Update interrupt disabled 0 Enabled Update interrupt enabled 1 SR SR status register 0x10 0x10 read-write 0x00000000 2 0x1 1-2 CC%sOF Capture/Compare %s overcapture flag 9 1 zeroToClear CC1OFR read NoOvercapture No overcapture has been detected 0 Overcapture The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set 1 CC1OFW write Clear Clear flag 0 BIF Break interrupt flag 7 1 zeroToClear BIFR read NoTrigger No break event occurred 0 Trigger An active level has been detected on the break input. An interrupt is generated if BIE=1 in the TIMx_DIER register 1 BIFW write Clear Clear flag 0 TIF Trigger interrupt flag 6 1 zeroToClear TIFR read NoTrigger No trigger event occurred 0 Trigger Trigger interrupt pending 1 TIFW write Clear Clear flag 0 COMIF COM interrupt flag 5 1 zeroToClear COMIFR read NoCOM No COM event occurred 0 COM COM interrupt pending 1 COMIFW write Clear Clear flag 0 2 0x1 1-2 CC%sIF Capture/compare %s interrupt flag 1 1 zeroToClear CC1IFR read NoMatch No campture/compare has been detected 0 Match If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register. 1 CC1IFW write Clear Clear flag 0 UIF Update interrupt flag 0 1 zeroToClear UIFR read NoUpdateOccurred No update occurred 0 UpdatePending Update interrupt pending 1 UIFW write Clear Clear flag 0 EGR EGR event generation register 0x14 0x10 0x00000000 BG Break generation 7 1 write-only BGW Trigger A break event is generated. MOE bit is cleared and BIF flag is set. Related interrupt or DMA transfer can occur if enabled 1 TG Trigger generation 6 1 write-only TGW Trigger The TIF flag is set in TIMx_SR register. Related interrupt or DMA transfer can occur if enabled. 1 COMG Capture/Compare control update generation 5 1 read-write COMGW write Trigger When CCPC bit is set, it allows CCxE, CCxNE and OCxM bits to be updated 1 2 0x1 1-2 CC%sG Capture/compare %s generation 1 1 write-only CC1GW Trigger If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register. 1 UG Update generation 0 1 write-only UG Update Re-initializes the timer counter and generates an update of the registers. 1 CCMR1_Output CCMR1_Output capture/compare mode register (output mode) 0x18 0x20 read-write 0x00000000 2 0x8 1-2 OC%sM_3 Output compare %s mode, bit 3 16 1 OC1M_3 Normal Normal output compare mode (modes 0-7) 0 Extended Extended output compare mode (modes 7-15) 1 2 0x8 1-2 OC%sM Output compare %s mode 4 3 OC1M Frozen The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive 0 ActiveOnMatch Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1 1 InactiveOnMatch Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved 2 Toggle OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved 3 ForceInactive OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF 4 ForceActive OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF 5 PwmMode1 In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / Reserved 6 PwmMode2 Inversely to PwmMode1 / Reserved 7 2 0x8 1-2 OC%sPE Output compare %s preload enable 3 1 OC1PE Disabled Preload register on CCRx disabled. New values written to CCRx are taken into account immediately 0 Enabled Preload register on CCRx enabled. Preload value is loaded into active register on each update event 1 2 0x8 1-2 OC%sFE Output compare %s fast enable 2 1 OC1FE Disabled Fast output disabled 0 Enabled Fast output enabled 1 2 0x8 1-2 CC%sS Capture/Compare %s selection 0 2 CC1S Output CCx channel is configured as output 0 CCMR1_Input CCMR1_Input capture/compare mode register 1 (input mode) CCMR1_Output 0x18 0x20 read-write 0x00000000 2 0x8 1-2 IC%sF Input capture %s filter 4 4 ICFilter NoFilter No filter, sampling is done at fDTS 0 FCK_INT_N2 fSAMPLING=fCK_INT, N=2 1 FCK_INT_N4 fSAMPLING=fCK_INT, N=4 2 FCK_INT_N8 fSAMPLING=fCK_INT, N=8 3 FDTS_Div2_N6 fSAMPLING=fDTS/2, N=6 4 FDTS_Div2_N8 fSAMPLING=fDTS/2, N=8 5 FDTS_Div4_N6 fSAMPLING=fDTS/4, N=6 6 FDTS_Div4_N8 fSAMPLING=fDTS/4, N=8 7 FDTS_Div8_N6 fSAMPLING=fDTS/8, N=6 8 FDTS_Div8_N8 fSAMPLING=fDTS/8, N=8 9 FDTS_Div16_N5 fSAMPLING=fDTS/16, N=5 10 FDTS_Div16_N6 fSAMPLING=fDTS/16, N=6 11 FDTS_Div16_N8 fSAMPLING=fDTS/16, N=8 12 FDTS_Div32_N5 fSAMPLING=fDTS/32, N=5 13 FDTS_Div32_N6 fSAMPLING=fDTS/32, N=6 14 FDTS_Div32_N8 fSAMPLING=fDTS/32, N=8 15 2 0x8 1-2 IC%sPSC Input capture %s prescaler 2 2 ICPrescaler NoPrescaler No prescaler, capture is done each time an edge is detected on the capture input 0 TwoEvents Capture is done once every 2 events 1 FourEvents Capture is done once every 4 events 2 EightEvents Capture is done once every 8 events 3 CC2S Capture/Compare 2 selection 8 2 CC2S TI2 CC2 channel is configured as input, IC2 is mapped on TI2 1 TI1 CC2 channel is configured as input, IC2 is mapped on TI1 2 TRC CC2 channel is configured as input, IC2 is mapped on TRC 3 CC1S Capture/Compare 1 selection 0 2 CC1S TI1 CC1 channel is configured as input, IC1 is mapped on TI1 1 TI2 CC1 channel is configured as input, IC1 is mapped on TI2 2 TRC CC1 channel is configured as input, IC1 is mapped on TRC 3 CCER CCER capture/compare enable register 0x20 0x10 read-write 0x00000000 2 0x4 1-2 CC%sNP Capture/Compare %s output Polarity 3 1 CC1NP ActiveHigh OCxN active high 0 ActiveLow OCxN active low 1 2 0x4 1-2 CC%sP Capture/Compare %s output Polarity 1 1 CC1P RisingEdge Noninverted/rising edge 0 FallingEdge Inverted/falling edge 1 2 0x4 1-2 CC%sE Capture/Compare %s output enable 0 1 CC1E Disabled Capture disabled 0 Enabled Capture enabled 1 1 0x0 1-1 CC%sNE Capture/Compare %s complementary output enable 2 1 CC1NE Disabled Complementary output disabled 0 Enabled Complementary output enabled 1 CNT CNT counter 0x24 0x20 0x00000000 CNT counter value 0 16 read-write 0 65535 UIFCPY UIF Copy 31 1 read-only CNT16 CNT16 16-bit counter register CNT 0x24 0x10 read-write 0x00000000 CNT counter value 0 16 read-write 0 65535 PSC PSC prescaler 0x28 0x10 read-write 0x00000000 PSC Prescaler value 0 16 0 65535 ARR ARR auto-reload register 0x2C 0x10 read-write 0x0000FFFF ARR Auto-reload value 0 16 0 65535 RCR RCR repetition counter register 0x30 0x10 read-write 0x00000000 REP Repetition counter value 0 8 0 255 2 0x4 1-2 CCR%s CCR%s capture/compare register 0x34 0x10 read-write 0x00000000 CCR Capture/Compare value 0 16 0 65535 BDTR BDTR break and dead-time register 0x44 0x20 read-write 0x00000000 DTG Dead-time generator setup 0 8 0 255 LOCK Lock configuration 8 2 LOCK Off No bit is write protected 0 Level1 Any bits except MOE, OSSR, OSSI and LOCK in TIMx_BDTR register, OISx and OISxN bits in TIMx_CR2 register can no longer be written 1 Level2 LOCK Level 1 + CC Polarity bits (CCxP/CCxNP bits in TIMx_CCER register, as long as the related channel is configured in output through the CCxS bits) as well as OSSR and OSSI bits can no longer be written 2 Level3 LOCK Level 2 + CC Control bits (OCxM and OCxPE bits in TIMx_CCMRx registers, as long as the related channel is configured in output through the CCxS bits) can no longer be written 3 OSSI Off-state selection for Idle mode 10 1 OSSI HiZ When inactive, OC/OCN outputs are disabled 0 IdleLevel When inactive, OC/OCN outputs are forced to idle level 1 OSSR Off-state selection for Run mode 11 1 OSSR HiZ When inactive, OC/OCN outputs are disabled 0 IdleLevel When inactive, OC/OCN outputs are enabled with their inactive level 1 BKE Break enable 12 1 BKE Disabled Break function x disabled 0 Enabled Break function x enabled 1 BKP Break polarity 13 1 BKP ActiveLow Break input BRKx is active low 0 ActiveHigh Break input BRKx is active high 1 AOE Automatic output enable 14 1 AOE Manual MOE can be set only by software 0 Automatic MOE can be set by software or automatically at the next update event (if none of the break inputs BRK and BRK2 is active) 1 MOE Main output enable 15 1 MOE DisabledIdle OC/OCN are disabled or forced idle depending on OSSI 0 Enabled OC/OCN are enabled if CCxE/CCxNE are set 1 DCR DCR DMA control register 0x48 0x10 read-write 0x00000000 DBL DMA burst length 8 5 DBA DMA base address 0 5 DMAR DMAR DMA address for full transfer 0x4C 0x10 read-write 0x00000000 DMAB DMA register for burst accesses 0 16 OR1 OR1 TIM15 option register 1 0x50 0x20 read-write 0x00000000 TI1_RMP Input capture 1 remap 0 1 ENCODER_MODE Encoder mode 1 2 OR2 OR2 TIM15 option register 2 0x60 0x20 read-write 0x00000001 BKINE BRK BKIN input enable 0 1 BKCMP1E BRK COMP1 enable 1 1 BKCMP2E BRK COMP2 enable 2 1 BKDFBK0E BRK DFSDM_BREAK[0] enablee 8 1 BKINP BRK BKIN input polarity 9 1 BKCMP1P BRK COMP1 input polarity 10 1 BKCMP2P BRK COMP2 input polarity 11 1 TIM16 General purpose timers TIM 0x40014400 0x0 0x400 registers CR1 CR1 control register 1 0x0 0x10 read-write 0x00000000 CEN Counter enable 0 1 CEN Disabled Counter disabled 0 Enabled Counter enabled 1 UDIS Update disable 1 1 UDIS Enabled Update event enabled 0 Disabled Update event disabled 1 URS Update request source 2 1 URS AnyEvent Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request 0 CounterOnly Only counter overflow/underflow generates an update interrupt or DMA request 1 OPM One-pulse mode 3 1 OPM Disabled Counter is not stopped at update event 0 Enabled Counter stops counting at the next update event (clearing the CEN bit) 1 ARPE Auto-reload preload enable 7 1 ARPE Disabled TIMx_APRR register is not buffered 0 Enabled TIMx_APRR register is buffered 1 CKD Clock division 8 2 CKD Div1 t_DTS = t_CK_INT 0 Div2 t_DTS = 2 × t_CK_INT 1 Div4 t_DTS = 4 × t_CK_INT 2 UIFREMAP UIF status bit remapping 11 1 CR2 CR2 control register 2 0x4 0x10 read-write 0x00000000 1 0x0 1-1 OIS%sN Output Idle state (OC%sN output) 9 1 OIS1N Reset OCxN=0 after a dead-time when MOE=0 0 Set OCxN=1 after a dead-time when MOE=0 1 1 0x0 1-1 OIS%s Output Idle state (OC%s output) 8 1 OIS1 Reset OCx=0 (after a dead-time if OCx(N) is implemented) when MOE=0 0 Set OCx=1 (after a dead-time if OCx(N) is implemented) when MOE=0 1 CCDS Capture/compare DMA selection 3 1 CCDS OnCompare CCx DMA request sent when CCx event occurs 0 OnUpdate CCx DMA request sent when update event occurs 1 CCUS Capture/compare control update selection 2 1 CCUS Sw When capture/compare control bits are preloaded (CCPC=1), they are updated by setting the COMG bit only 0 SwOrEdge When capture/compare control bits are preloaded (CCPC=1), they are updated by setting the COMG bit or when an rising edge occurs on TRGI 1 CCPC Capture/compare preloaded control 0 1 CCPC NotPreloaded CCxE, CCxNE and OCxM bits are not preloaded 0 Preloaded CCxE, CCxNE and OCxM bits are preloaded 1 DIER DIER DMA/Interrupt enable register 0xC 0x10 read-write 0x00000000 TDE Trigger DMA request enable 14 1 COMDE COM DMA request enable 13 1 1 0x0 1-1 CC%sDE Capture/Compare %s DMA request enable 9 1 CC1DE Disabled CCx DMA request disabled 0 Enabled CCx DMA request enabled 1 UDE Update DMA request enable 8 1 UDE Disabled Update DMA request disabled 0 Enabled Update DMA request enabled 1 BIE Break interrupt enable 7 1 BIE Disabled Break interrupt disabled 0 Enabled Break interrupt enabled 1 COMIE COM interrupt enable 5 1 COMIE Disabled COM interrupt disabled 0 Enabled COM interrupt enabled 1 1 0x0 1-1 CC%sIE Capture/Compare %s interrupt enable 1 1 CC1IE Disabled CCx interrupt disabled 0 Enabled CCx interrupt enabled 1 UIE Update interrupt enable 0 1 UIE Disabled Update interrupt disabled 0 Enabled Update interrupt enabled 1 SR SR status register 0x10 0x10 read-write 0x00000000 1 0x0 1-1 CC%sOF Capture/Compare %s overcapture flag 9 1 zeroToClear CC1OFR read NoOvercapture No overcapture has been detected 0 Overcapture The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set 1 CC1OFW write Clear Clear flag 0 BIF Break interrupt flag 7 1 zeroToClear BIFR read NoTrigger No break event occurred 0 Trigger An active level has been detected on the break input. An interrupt is generated if BIE=1 in the TIMx_DIER register 1 BIFW write Clear Clear flag 0 COMIF COM interrupt flag 5 1 zeroToClear COMIFR read NoCOM No COM event occurred 0 COM COM interrupt pending 1 COMIFW write Clear Clear flag 0 1 0x0 1-1 CC%sIF Capture/compare %s interrupt flag 1 1 zeroToClear CC1IFR read NoMatch No campture/compare has been detected 0 Match If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register. 1 CC1IFW write Clear Clear flag 0 UIF Update interrupt flag 0 1 zeroToClear UIFR read NoUpdateOccurred No update occurred 0 UpdatePending Update interrupt pending 1 UIFW write Clear Clear flag 0 EGR EGR event generation register 0x14 0x10 write-only 0x00000000 BG Break generation 7 1 BGW Trigger A break event is generated. MOE bit is cleared and BIF flag is set. Related interrupt or DMA transfer can occur if enabled 1 COMG Capture/Compare control update generation 5 1 COMGW Trigger When CCPC bit is set, it allows CCxE, CCxNE and OCxM bits to be updated 1 1 0x0 1-1 CC%sG Capture/compare %s generation 1 1 CC1GW Trigger If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register. 1 UG Update generation 0 1 UG Update Re-initializes the timer counter and generates an update of the registers. 1 CCMR1_Output CCMR1_Output capture/compare mode register (output mode) 0x18 0x20 read-write 0x00000000 1 0x0 1-1 OC%sM_3 Output compare %s mode, bit 3 16 1 1 0x0 1-1 OC%sM Output compare %s mode 4 3 OC1M Frozen The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs 0 ActiveOnMatch Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register 1 InactiveOnMatch Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register 2 Toggle OCyREF toggles when TIMx_CNT=TIMx_CCRy 3 ForceInactive OCyREF is forced low 4 ForceActive OCyREF is forced high 5 PwmMode1 In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active 6 PwmMode2 Inversely to PwmMode1 7 1 0x0 1-1 OC%sPE Output compare %s preload enable 3 1 OC1PE Disabled Preload register on CCRx disabled. New values written to CCRx are taken into account immediately 0 Enabled Preload register on CCRx enabled. Preload value is loaded into active register on each update event 1 1 0x0 1-1 OC%sFE Output compare %s fast enable 2 1 OC1FE Disabled Fast output disabled 0 Enabled Fast output enabled 1 1 0x0 1-1 CC%sS Capture/Compare %s selection 0 2 CC1S Output CCx channel is configured as output 0 CCMR1_Input CCMR1_Input capture/compare mode register 1 (input mode) CCMR1_Output 0x18 0x20 read-write 0x00000000 1 0x0 1-1 IC%sF Input capture %s filter 4 4 ICFilter NoFilter No filter, sampling is done at fDTS 0 FCK_INT_N2 fSAMPLING=fCK_INT, N=2 1 FCK_INT_N4 fSAMPLING=fCK_INT, N=4 2 FCK_INT_N8 fSAMPLING=fCK_INT, N=8 3 FDTS_Div2_N6 fSAMPLING=fDTS/2, N=6 4 FDTS_Div2_N8 fSAMPLING=fDTS/2, N=8 5 FDTS_Div4_N6 fSAMPLING=fDTS/4, N=6 6 FDTS_Div4_N8 fSAMPLING=fDTS/4, N=8 7 FDTS_Div8_N6 fSAMPLING=fDTS/8, N=6 8 FDTS_Div8_N8 fSAMPLING=fDTS/8, N=8 9 FDTS_Div16_N5 fSAMPLING=fDTS/16, N=5 10 FDTS_Div16_N6 fSAMPLING=fDTS/16, N=6 11 FDTS_Div16_N8 fSAMPLING=fDTS/16, N=8 12 FDTS_Div32_N5 fSAMPLING=fDTS/32, N=5 13 FDTS_Div32_N6 fSAMPLING=fDTS/32, N=6 14 FDTS_Div32_N8 fSAMPLING=fDTS/32, N=8 15 1 0x0 1-1 IC%sPSC Input capture %s prescaler 2 2 ICPrescaler NoPrescaler No prescaler, capture is done each time an edge is detected on the capture input 0 TwoEvents Capture is done once every 2 events 1 FourEvents Capture is done once every 4 events 2 EightEvents Capture is done once every 8 events 3 CC1S Capture/Compare 1 selection 0 2 CC1S TI1 CC1 channel is configured as input, IC1 is mapped on TI1 1 CCER CCER capture/compare enable register 0x20 0x10 read-write 0x00000000 1 0x0 1-1 CC%sNP Capture/Compare %s output Polarity 3 1 CC1NP ActiveHigh OCxN active high 0 ActiveLow OCxN active low 1 1 0x0 1-1 CC%sNE Capture/Compare %s complementary output enable 2 1 CC1NE Disabled Complementary output disabled 0 Enabled Complementary output enabled 1 1 0x0 1-1 CC%sP Capture/Compare %s output Polarity 1 1 CC1P RisingEdge Noninverted/rising edge 0 FallingEdge Inverted/falling edge 1 1 0x0 1-1 CC%sE Capture/Compare %s output enable 0 1 CC1E Disabled Capture disabled 0 Enabled Capture enabled 1 CNT CNT counter 0x24 0x20 0x00000000 CNT counter value 0 16 read-write 0 65535 UIFCPY UIF Copy 31 1 read-only CNT16 CNT16 16-bit counter register CNT 0x24 0x10 read-write 0x00000000 CNT counter value 0 16 read-write 0 65535 PSC PSC prescaler 0x28 0x10 read-write 0x00000000 PSC Prescaler value 0 16 0 65535 ARR ARR auto-reload register 0x2C 0x10 read-write 0x0000FFFF ARR Auto-reload value 0 16 0 65535 RCR RCR repetition counter register 0x30 0x10 read-write 0x00000000 REP Repetition counter value 0 8 0 255 1 0x2 1-1 CCR%s CCR%s capture/compare register 0x34 0x10 read-write 0x00000000 CCR Capture/Compare value 0 16 0 65535 BDTR BDTR break and dead-time register 0x44 0x20 read-write 0x00000000 DTG Dead-time generator setup 0 8 0 255 LOCK Lock configuration 8 2 LOCK Off No bit is write protected 0 Level1 Any bits except MOE, OSSR, OSSI and LOCK in TIMx_BDTR register, OISx and OISxN bits in TIMx_CR2 register can no longer be written 1 Level2 LOCK Level 1 + CC Polarity bits (CCxP/CCxNP bits in TIMx_CCER register, as long as the related channel is configured in output through the CCxS bits) as well as OSSR and OSSI bits can no longer be written 2 Level3 LOCK Level 2 + CC Control bits (OCxM and OCxPE bits in TIMx_CCMRx registers, as long as the related channel is configured in output through the CCxS bits) can no longer be written 3 OSSI Off-state selection for Idle mode 10 1 OSSI HiZ When inactive, OC/OCN outputs are disabled 0 IdleLevel When inactive, OC/OCN outputs are forced to idle level 1 OSSR Off-state selection for Run mode 11 1 OSSR HiZ When inactive, OC/OCN outputs are disabled 0 IdleLevel When inactive, OC/OCN outputs are enabled with their inactive level 1 BKE Break enable 12 1 BKE Disabled Break function x disabled 0 Enabled Break function x enabled 1 BKP Break polarity 13 1 BKP ActiveLow Break input BRKx is active low 0 ActiveHigh Break input BRKx is active high 1 AOE Automatic output enable 14 1 AOE Manual MOE can be set only by software 0 Automatic MOE can be set by software or automatically at the next update event (if none of the break inputs BRK and BRK2 is active) 1 MOE Main output enable 15 1 MOE DisabledIdle OC/OCN are disabled or forced idle depending on OSSI 0 Enabled OC/OCN are enabled if CCxE/CCxNE are set 1 DCR DCR DMA control register 0x48 0x10 read-write 0x00000000 DBL DMA burst length 8 5 DBA DMA base address 0 5 DMAR DMAR DMA address for full transfer 0x4C 0x10 read-write 0x00000000 DMAB DMA register for burst accesses 0 16 OR1 OR1 TIM16 option register 1 0x50 0x20 read-write 0x00000000 TI1_RMP Input capture 1 remap 0 2 OR2 OR2 TIM17 option register 1 0x60 0x20 read-write 0x00000001 BKINE BRK BKIN input enable 0 1 BKCMP1E BRK COMP1 enable 1 1 BKCMP2E BRK COMP2 enable 2 1 BKDFBK1E BRK DFSDM_BREAK[1] enable 8 1 BKINP BRK BKIN input polarity 9 1 BKCMP1P BRK COMP1 input polarity 10 1 BKCMP2P BRK COMP2 input polarit 11 1 TIM17 TIM 0x40014800 TIM1 Advanced-timers TIM 0x40012C00 0x0 0x400 registers TIM1_BRK_TIM15 TIM1 Break/TIM15 global interrupts 24 TIM1_UP_TIM16 TIM1 Update/TIM16 global interrupts 25 TIM1_TRG_COM_TIM17 TIM1 Trigger and Commutation interrupts and TIM17 global interrupt 26 TIM1_CC TIM1 Capture Compare interrupt 27 CR1 CR1 control register 1 0x0 0x10 read-write 0x00000000 UIFREMAP UIF status bit remapping 11 1 CKD Clock division 8 2 CKD Div1 t_DTS = t_CK_INT 0 Div2 t_DTS = 2 × t_CK_INT 1 Div4 t_DTS = 4 × t_CK_INT 2 ARPE Auto-reload preload enable 7 1 ARPE Disabled TIMx_APRR register is not buffered 0 Enabled TIMx_APRR register is buffered 1 CMS Center-aligned mode selection 5 2 CMS EdgeAligned The counter counts up or down depending on the direction bit 0 CenterAligned1 The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting down. 1 CenterAligned2 The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting up. 2 CenterAligned3 The counter counts up and down alternatively. Output compare interrupt flags are set both when the counter is counting up or down. 3 DIR Direction 4 1 DIR Up Counter used as upcounter 0 Down Counter used as downcounter 1 OPM One-pulse mode 3 1 OPM Disabled Counter is not stopped at update event 0 Enabled Counter stops counting at the next update event (clearing the CEN bit) 1 URS Update request source 2 1 URS AnyEvent Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request 0 CounterOnly Only counter overflow/underflow generates an update interrupt or DMA request 1 UDIS Update disable 1 1 UDIS Enabled Update event enabled 0 Disabled Update event disabled 1 CEN Counter enable 0 1 CEN Disabled Counter disabled 0 Enabled Counter enabled 1 CR2 CR2 control register 2 0x4 0x20 read-write 0x00000000 MMS2 Master mode selection 2 20 4 6 0x2 1-6 OIS%s Output Idle state (OC%s output) 8 1 OIS1 Reset OCx=0 (after a dead-time if OCx(N) is implemented) when MOE=0 0 Set OCx=1 (after a dead-time if OCx(N) is implemented) when MOE=0 1 3 0x2 1-3 OIS%sN Output Idle state (OC%sN output) 9 1 OIS1N Reset OCxN=0 after a dead-time when MOE=0 0 Set OCxN=1 after a dead-time when MOE=0 1 TI1S TI1 selection 7 1 TI1S Normal The TIMx_CH1 pin is connected to TI1 input 0 XOR The TIMx_CH1, CH2, CH3 pins are connected to TI1 input 1 MMS Master mode selection 4 3 MMS Reset The UG bit from the TIMx_EGR register is used as trigger output 0 Enable The counter enable signal, CNT_EN, is used as trigger output 1 Update The update event is selected as trigger output 2 ComparePulse The trigger output send a positive pulse when the CC1IF flag it to be set, as soon as a capture or a compare match occurred 3 CompareOC1 OC1REF signal is used as trigger output 4 CompareOC2 OC2REF signal is used as trigger output 5 CompareOC3 OC3REF signal is used as trigger output 6 CompareOC4 OC4REF signal is used as trigger output 7 CCDS Capture/compare DMA selection 3 1 CCDS OnCompare CCx DMA request sent when CCx event occurs 0 OnUpdate CCx DMA request sent when update event occurs 1 CCUS Capture/compare control update selection 2 1 CCUS Sw When capture/compare control bits are preloaded (CCPC=1), they are updated by setting the COMG bit only 0 SwOrEdge When capture/compare control bits are preloaded (CCPC=1), they are updated by setting the COMG bit or when an rising edge occurs on TRGI 1 CCPC Capture/compare preloaded control 0 1 CCPC NotPreloaded CCxE, CCxNE and OCxM bits are not preloaded 0 Preloaded CCxE, CCxNE and OCxM bits are preloaded 1 SMCR SMCR slave mode control register 0x8 0x20 read-write 0x00000000 SMS_3 Slave mode selection - bit 3 16 1 ETP External trigger polarity 15 1 ETP NotInverted ETR is noninverted, active at high level or rising edge 0 Inverted ETR is inverted, active at low level or falling edge 1 ECE External clock enable 14 1 ECE Disabled External clock mode 2 disabled 0 Enabled External clock mode 2 enabled. The counter is clocked by any active edge on the ETRF signal. 1 ETPS External trigger prescaler 12 2 ETPS Div1 Prescaler OFF 0 Div2 ETRP frequency divided by 2 1 Div4 ETRP frequency divided by 4 2 Div8 ETRP frequency divided by 8 3 ETF External trigger filter 8 4 ETF NoFilter No filter, sampling is done at fDTS 0 FCK_INT_N2 fSAMPLING=fCK_INT, N=2 1 FCK_INT_N4 fSAMPLING=fCK_INT, N=4 2 FCK_INT_N8 fSAMPLING=fCK_INT, N=8 3 FDTS_Div2_N6 fSAMPLING=fDTS/2, N=6 4 FDTS_Div2_N8 fSAMPLING=fDTS/2, N=8 5 FDTS_Div4_N6 fSAMPLING=fDTS/4, N=6 6 FDTS_Div4_N8 fSAMPLING=fDTS/4, N=8 7 FDTS_Div8_N6 fSAMPLING=fDTS/8, N=6 8 FDTS_Div8_N8 fSAMPLING=fDTS/8, N=8 9 FDTS_Div16_N5 fSAMPLING=fDTS/16, N=5 10 FDTS_Div16_N6 fSAMPLING=fDTS/16, N=6 11 FDTS_Div16_N8 fSAMPLING=fDTS/16, N=8 12 FDTS_Div32_N5 fSAMPLING=fDTS/32, N=5 13 FDTS_Div32_N6 fSAMPLING=fDTS/32, N=6 14 FDTS_Div32_N8 fSAMPLING=fDTS/32, N=8 15 MSM Master/Slave mode 7 1 MSM NoSync No action 0 Sync The effect of an event on the trigger input (TRGI) is delayed to allow a perfect synchronization between the current timer and its slaves (through TRGO). It is useful if we want to synchronize several timers on a single external event. 1 TS Trigger selection 4 3 TS ITR0 Internal Trigger 0 (ITR0) 0 ITR1 Internal Trigger 1 (ITR1) 1 ITR2 Internal Trigger 2 (ITR2) 2 TI1F_ED TI1 Edge Detector (TI1F_ED) 4 TI1FP1 Filtered Timer Input 1 (TI1FP1) 5 TI2FP2 Filtered Timer Input 2 (TI2FP2) 6 ETRF External Trigger input (ETRF) 7 OCCS OCREF clear selection 3 1 SMS Slave mode selection 0 3 SMS Disabled Slave mode disabled - if CEN = ‘1 then the prescaler is clocked directly by the internal clock. 0 Encoder_Mode_1 Encoder mode 1 - Counter counts up/down on TI2FP1 edge depending on TI1FP2 level. 1 Encoder_Mode_2 Encoder mode 2 - Counter counts up/down on TI1FP2 edge depending on TI2FP1 level. 2 Encoder_Mode_3 Encoder mode 3 - Counter counts up/down on both TI1FP1 and TI2FP2 edges depending on the level of the other input. 3 Reset_Mode Reset Mode - Rising edge of the selected trigger input (TRGI) reinitializes the counter and generates an update of the registers. 4 Gated_Mode Gated Mode - The counter clock is enabled when the trigger input (TRGI) is high. The counter stops (but is not reset) as soon as the trigger becomes low. Both start and stop of the counter are controlled. 5 Trigger_Mode Trigger Mode - The counter starts at a rising edge of the trigger TRGI (but it is not reset). Only the start of the counter is controlled. 6 Ext_Clock_Mode External Clock Mode 1 - Rising edges of the selected trigger (TRGI) clock the counter. 7 DIER DIER DMA/Interrupt enable register 0xC 0x10 read-write 0x00000000 TDE Trigger DMA request enable 14 1 TDE Disabled Trigger DMA request disabled 0 Enabled Trigger DMA request enabled 1 COMDE COM DMA request enable 13 1 COMDE Disabled COM DMA request disabled 0 Enabled COM DMA request enabled 1 4 0x1 1-4 CC%sDE Capture/Compare %s DMA request enable 9 1 CC1DE Disabled CCx DMA request disabled 0 Enabled CCx DMA request enabled 1 UDE Update DMA request enable 8 1 UDE Disabled Update DMA request disabled 0 Enabled Update DMA request enabled 1 BIE Break interrupt enable 7 1 BIE Disabled Break interrupt disabled 0 Enabled Break interrupt enabled 1 TIE Trigger interrupt enable 6 1 TIE Disabled Trigger interrupt disabled 0 Enabled Trigger interrupt enabled 1 COMIE COM interrupt enable 5 1 COMIE Disabled COM interrupt disabled 0 Enabled COM interrupt enabled 1 4 0x1 1-4 CC%sIE Capture/Compare %s interrupt enable 1 1 CC1IE Disabled CCx interrupt disabled 0 Enabled CCx interrupt enabled 1 UIE Update interrupt enable 0 1 UIE Disabled Update interrupt disabled 0 Enabled Update interrupt enabled 1 SR SR status register 0x10 0x20 read-write 0x00000000 4 0x1 1-4 CC%sIF Capture/compare %s interrupt flag 1 1 zeroToClear CC1IFR read NoMatch No campture/compare has been detected 0 Match If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register. 1 CC1IFW write Clear Clear flag 0 CC6IF Compare 6 interrupt flag 17 1 zeroToClear read write CC5IF Compare 5 interrupt flag 16 1 zeroToClear read write SBIF System Break interrupt flag 13 1 zeroToClear SBIFR read NoTrigger No break event occurred 0 Trigger An active level has been detected on the system break input. An interrupt is generated if BIE=1 in the TIMx_DIER register 1 SBIFW write Clear Clear flag 0 4 0x1 1-4 CC%sOF Capture/Compare %s overcapture flag 9 1 zeroToClear CC1OFR read NoOvercapture No overcapture has been detected 0 Overcapture The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set 1 CC1OFW write Clear Clear flag 0 B2IF Break 2 interrupt flag 8 1 zeroToClear B2IFR read NoTrigger No break event occurred 0 Trigger An active level has been detected on the break 2 input. An interrupt is generated if BIE=1 in the TIMx_DIER register 1 B2IFW write Clear Clear flag 0 BIF Break interrupt flag 7 1 zeroToClear BIFR read NoTrigger No break event occurred 0 Trigger An active level has been detected on the break input. An interrupt is generated if BIE=1 in the TIMx_DIER register 1 BIFW write Clear Clear flag 0 TIF Trigger interrupt flag 6 1 zeroToClear TIFR read NoTrigger No trigger event occurred 0 Trigger Trigger interrupt pending 1 TIFW write Clear Clear flag 0 COMIF COM interrupt flag 5 1 zeroToClear COMIFR read NoCOM No COM event occurred 0 COM COM interrupt pending 1 COMIFW write Clear Clear flag 0 UIF Update interrupt flag 0 1 zeroToClear UIFR read NoUpdateOccurred No update occurred 0 UpdatePending Update interrupt pending 1 UIFW write Clear Clear flag 0 EGR EGR event generation register 0x14 0x10 write-only 0x00000000 B2G Break 2 generation 8 1 B2GW Trigger A break 2 event is generated. MOE bit is cleared and B2IF flag is set. Related interrupt can occur if enabled 1 BG Break generation 7 1 BGW Trigger A break event is generated. MOE bit is cleared and BIF flag is set. Related interrupt or DMA transfer can occur if enabled 1 TG Trigger generation 6 1 TGW Trigger The TIF flag is set in TIMx_SR register. Related interrupt or DMA transfer can occur if enabled. 1 COMG Capture/Compare control update generation 5 1 COMGW Trigger When CCPC bit is set, it allows CCxE, CCxNE and OCxM bits to be updated 1 4 0x1 1-4 CC%sG Capture/compare %s generation 1 1 CC1GW Trigger If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register. 1 UG Update generation 0 1 UG Update Re-initializes the timer counter and generates an update of the registers. 1 CCMR1_Output CCMR1_Output capture/compare mode register 1 0x18 0x20 read-write 0x00000000 2 0x8 1-2 OC%sM_3 Output compare %s mode, bit 3 16 1 OC1M_3 Normal Normal output compare mode (modes 0-7) 0 Extended Extended output compare mode (modes 7-15) 1 2 0x8 1-2 OC%sCE Output compare %s clear enable 7 1 OC1CE Disabled OCxRef is not affected by the ETRF signal 0 Enabled OCxRef is cleared as soon as a High level is detected on ETRF signal 1 2 0x8 1-2 OC%sM Output compare %s mode 4 3 OC1M Frozen The comparison between the output compare register TIMx_CCRy and the counter TIMx_CNT has no effect on the outputs / OpmMode1: Retriggerable OPM mode 1 - In up-counting mode, the channel is active until a trigger event is detected (on TRGI signal). In down-counting mode, the channel is inactive 0 ActiveOnMatch Set channel to active level on match. OCyREF signal is forced high when the counter matches the capture/compare register / OpmMode2: Inversely to OpmMode1 1 InactiveOnMatch Set channel to inactive level on match. OCyREF signal is forced low when the counter matches the capture/compare register / Reserved 2 Toggle OCyREF toggles when TIMx_CNT=TIMx_CCRy / Reserved 3 ForceInactive OCyREF is forced low / CombinedPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC is the logical OR between OC1REF and OC2REF 4 ForceActive OCyREF is forced high / CombinedPwmMode2: OCyREF has the same behavior as in PWM mode 2. OCyREFC is the logical AND between OC1REF and OC2REF 5 PwmMode1 In upcounting, channel is active as long as TIMx_CNT<TIMx_CCRy else inactive. In downcounting, channel is inactive as long as TIMx_CNT>TIMx_CCRy else active / AsymmetricPwmMode1: OCyREF has the same behavior as in PWM mode 1. OCyREFC outputs OC1REF when the counter is counting up, OC2REF when it is counting down 6 PwmMode2 Inversely to PwmMode1 / AsymmetricPwmMode2: Inversely to AsymmetricPwmMode1 7 2 0x8 1-2 OC%sPE Output compare %s preload enable 3 1 OC1PE Disabled Preload register on CCRx disabled. New values written to CCRx are taken into account immediately 0 Enabled Preload register on CCRx enabled. Preload value is loaded into active register on each update event 1 2 0x8 1-2 OC%sFE Output compare %s fast enable 2 1 OC1FE Disabled Fast output disabled 0 Enabled Fast output enabled 1 2 0x8 1-2 CC%sS Capture/Compare %s selection 0 2 CC1S Output CCx channel is configured as output 0 CCMR1_Input CCMR1_Input capture/compare mode register 1 (input mode) CCMR1_Output 0x18 0x20 read-write 0x00000000 2 0x8 1-2 IC%sF Input capture %s filter 4 4 ICFilter NoFilter No filter, sampling is done at fDTS 0 FCK_INT_N2 fSAMPLING=fCK_INT, N=2 1 FCK_INT_N4 fSAMPLING=fCK_INT, N=4 2 FCK_INT_N8 fSAMPLING=fCK_INT, N=8 3 FDTS_Div2_N6 fSAMPLING=fDTS/2, N=6 4 FDTS_Div2_N8 fSAMPLING=fDTS/2, N=8 5 FDTS_Div4_N6 fSAMPLING=fDTS/4, N=6 6 FDTS_Div4_N8 fSAMPLING=fDTS/4, N=8 7 FDTS_Div8_N6 fSAMPLING=fDTS/8, N=6 8 FDTS_Div8_N8 fSAMPLING=fDTS/8, N=8 9 FDTS_Div16_N5 fSAMPLING=fDTS/16, N=5 10 FDTS_Div16_N6 fSAMPLING=fDTS/16, N=6 11 FDTS_Div16_N8 fSAMPLING=fDTS/16, N=8 12 FDTS_Div32_N5 fSAMPLING=fDTS/32, N=5 13 FDTS_Div32_N6 fSAMPLING=fDTS/32, N=6 14 FDTS_Div32_N8 fSAMPLING=fDTS/32, N=8 15 2 0x8 1-2 IC%sPSC Input capture %s prescaler 2 2 ICPrescaler NoPrescaler No prescaler, capture is done each time an edge is detected on the capture input 0 TwoEvents Capture is done once every 2 events 1 FourEvents Capture is done once every 4 events 2 EightEvents Capture is done once every 8 events 3 CC2S Capture/Compare 2 selection 8 2 CC2S TI2 CC2 channel is configured as input, IC2 is mapped on TI2 1 TI1 CC2 channel is configured as input, IC2 is mapped on TI1 2 TRC CC2 channel is configured as input, IC2 is mapped on TRC 3 CC1S Capture/Compare 1 selection 0 2 CC1S TI1 CC1 channel is configured as input, IC1 is mapped on TI1 1 TI2 CC1 channel is configured as input, IC1 is mapped on TI2 2 TRC CC1 channel is configured as input, IC1 is mapped on TRC 3 CCMR2_Output CCMR2_Output capture/compare mode register 2 (output mode) 0x1C 0x20 read-write 0x00000000 2 0x8 3-4 OC%sM_3 Output compare %s mode, bit 3 16 1 2 0x8 3-4 OC%sCE Output compare %s clear enable 7 1 2 0x8 3-4 OC%sM Output compare %s mode 4 3 2 0x8 3-4 OC%sPE Output compare %s preload enable 3 1 2 0x8 3-4 OC%sFE Output compare %s fast enable 2 1 2 0x8 3-4 CC%sS Capture/Compare %s selection 0 2 CCMR2_Input CCMR2_Input capture/compare mode register 2 (input mode) CCMR2_Output 0x1C 0x20 read-write 0x00000000 2 0x8 3-4 IC%sF Input capture %s filter 4 4 2 0x8 3-4 IC%sPSC Input capture %s prescaler 2 2 CC4S Capture/Compare 4 selection 8 2 CC4S TI4 CC4 channel is configured as input, IC4 is mapped on TI4 1 TI3 CC4 channel is configured as input, IC4 is mapped on TI3 2 TRC CC4 channel is configured as input, IC4 is mapped on TRC 3 CC3S Capture/compare 3 selection 0 2 CC3S TI3 CC3 channel is configured as input, IC3 is mapped on TI3 1 TI4 CC3 channel is configured as input, IC3 is mapped on TI4 2 TRC CC3 channel is configured as input, IC3 is mapped on TRC 3 CCER CCER capture/compare enable register 0x20 0x20 read-write 0x00000000 6 0x4 1-6 CC%sP Capture/Compare %s output Polarity 1 1 CC1P RisingEdge Noninverted/rising edge 0 FallingEdge Inverted/falling edge 1 6 0x4 1-6 CC%sE Capture/Compare %s output enable 0 1 CC1E Disabled Capture disabled 0 Enabled Capture enabled 1 4 0x4 1-4 CC%sNP Capture/Compare %s output Polarity 3 1 CC1NP ActiveHigh OCxN active high 0 ActiveLow OCxN active low 1 3 0x4 1-3 CC%sNE Capture/Compare %s complementary output enable 2 1 CC1NE Disabled Complementary output disabled 0 Enabled Complementary output enabled 1 CNT CNT counter 0x24 0x20 read-write 0x00000000 UIFCPY UIF copy 31 1 CNT counter value 0 16 0 65535 CNT16 CNT16 16-bit counter register CNT 0x24 0x10 read-write 0x00000000 CNT counter value 0 16 read-write 0 65535 PSC PSC prescaler 0x28 0x10 read-write 0x00000000 PSC Prescaler value 0 16 0 65535 ARR ARR auto-reload register 0x2C 0x10 read-write 0x0000FFFF ARR Auto-reload value 0 16 0 65535 RCR RCR repetition counter register 0x30 0x20 read-write 0x00000000 REP Repetition counter value 0 16 0 65535 4 0x4 1-4 CCR%s CCR%s capture/compare register 0x34 0x10 read-write 0x00000000 CCR Capture/Compare value 0 16 0 65535 BDTR BDTR break and dead-time register 0x44 0x20 read-write 0x00000000 BKP Break polarity 13 1 BKP ActiveLow Break input BRKx is active low 0 ActiveHigh Break input BRKx is active high 1 BK2P Break 2 polarity 25 1 BKE Break enable 12 1 BKE Disabled Break function x disabled 0 Enabled Break function x enabled 1 BK2E Break 2 enable 24 1 BK2F Break 2 filter 20 4 BKF Break filter 16 4 MOE Main output enable 15 1 MOE DisabledIdle OC/OCN are disabled or forced idle depending on OSSI 0 Enabled OC/OCN are enabled if CCxE/CCxNE are set 1 AOE Automatic output enable 14 1 AOE Manual MOE can be set only by software 0 Automatic MOE can be set by software or automatically at the next update event (if none of the break inputs BRK and BRK2 is active) 1 OSSR Off-state selection for Run mode 11 1 OSSR HiZ When inactive, OC/OCN outputs are disabled 0 IdleLevel When inactive, OC/OCN outputs are enabled with their inactive level 1 OSSI Off-state selection for Idle mode 10 1 OSSI HiZ When inactive, OC/OCN outputs are disabled 0 IdleLevel When inactive, OC/OCN outputs are forced to idle level 1 LOCK Lock configuration 8 2 LOCK Off No bit is write protected 0 Level1 Any bits except MOE, OSSR, OSSI and LOCK in TIMx_BDTR register, OISx and OISxN bits in TIMx_CR2 register can no longer be written 1 Level2 LOCK Level 1 + CC Polarity bits (CCxP/CCxNP bits in TIMx_CCER register, as long as the related channel is configured in output through the CCxS bits) as well as OSSR and OSSI bits can no longer be written 2 Level3 LOCK Level 2 + CC Control bits (OCxM and OCxPE bits in TIMx_CCMRx registers, as long as the related channel is configured in output through the CCxS bits) can no longer be written 3 DTG Dead-time generator setup 0 8 0 255 DCR DCR DMA control register 0x48 0x10 read-write 0x00000000 DBL DMA burst length 8 5 0 18 DBA DMA base address 0 5 0 31 DMAR DMAR DMA address for full transfer 0x4C 0x20 read-write 0x00000000 DMAB DMA register for burst accesses 0 32 OR1 OR1 TIM1 option register 1 0x50 0x20 read-write 0x00000000 ETR_ADC1_RMP External trigger remap on ADC1 analog watchdog 0 2 ETR_ADC3_RMP External trigger remap on ADC3 analog watchdog 2 2 TI1_RMP Input Capture 1 remap 4 1 CCMR3_Output CCMR3_Output capture/compare mode register 2 (output mode) 0x54 0x20 read-write 0x00000000 2 0x8 5-6 OC%sM_3 Output compare %s mode, bit 3 16 1 2 0x8 5-6 OC%sCE Output compare %s clear enable 7 1 2 0x8 5-6 OC%sM Output compare %s mode 4 3 2 0x8 5-6 OC%sPE Output compare %s preload enable 3 1 2 0x8 5-6 OC%sFE Output compare %s fast enable 2 1 CCR5 CCR5 capture/compare register 0x58 0x20 read-write 0x00000000 CCR Capture/Compare value 0 16 0 65535 GC5C1 Group Channel 5 and Channel 1 29 1 GC5C2 Group Channel 5 and Channel 2 30 1 GC5C3 Group Channel 5 and Channel 3 31 1 CCR6 CCR6 capture/compare register 0x5C 0x10 read-write 0x00000000 CCR Capture/Compare value 0 16 0 65535 OR2 OR2 TIM1 option register 2 0x60 0x20 read-write 0x00000001 BKINE BRK BKIN input enable 0 1 BKCMP1E BRK COMP1 enable 1 1 BKCMP2E BRK COMP2 enable 2 1 BKDFBK0E BRK DFSDM_BREAK[0] enable 8 1 BKINP BRK BKIN input polarity 9 1 BKCMP1P BRK COMP1 input polarity 10 1 BKCMP2P BRK COMP2 input polarity 11 1 ETRSEL ETR source selection 14 3 OR3 OR3 TIM1 option register 3 0x64 0x20 read-write 0x00000001 BK2INE BRK2 BKIN input enable 0 1 BK2CMP1E BRK2 COMP1 enable 1 1 BK2CMP2E BRK2 COMP2 enable 2 1 BK2DFBK1E BRK2 DFSDM_BREAK[1] enable 8 1 BK2INP BRK2 BKIN input polarity 9 1 BK2CMP1P BRK2 COMP1 input polarity 10 1 BK2CMP2P BRK2 COMP2 input polarity 11 1 TIM8 Advanced-timers TIM 0x40013400 0x0 0x400 registers TIM8_BRK TIM8 Break Interrupt 43 TIM8_UP TIM8 Update Interrupt 44 TIM8_TRG_COM TIM8 Trigger and Commutation Interrupt 45 TIM8_CC TIM8 Capture Compare Interrupt 46 CR1 CR1 control register 1 0x0 CR2 CR2 control register 2 0x4 SMCR SMCR slave mode control register 0x8 0x20 read-write 0x00000000 SMS_3 Slave mode selection - bit 3 16 1 ETP External trigger polarity 15 1 ECE External clock enable 14 1 ETPS External trigger prescaler 12 2 ETF External trigger filter 8 4 MSM Master/Slave mode 7 1 TS Trigger selection 4 3 TS ITR0 Internal Trigger 0 (ITR0) 0 ITR1 Internal Trigger 1 (ITR1) 1 ITR2 Internal Trigger 2 (ITR2) 2 TI1F_ED TI1 Edge Detector (TI1F_ED) 4 TI1FP1 Filtered Timer Input 1 (TI1FP1) 5 TI2FP2 Filtered Timer Input 2 (TI2FP2) 6 ETRF External Trigger input (ETRF) 7 OCCS OCREF clear selection 3 1 SMS Slave mode selection 0 3 DIER DIER DMA/Interrupt enable register 0xC SR SR status register 0x10 EGR EGR event generation register 0x14 CCMR1_Output CCMR1_Output capture/compare mode register 1 0x18 CCMR1_Input CCMR1_Input capture/compare mode register 1 (input mode) CCMR1_Output 0x18 CCMR2_Output CCMR2_Output capture/compare mode register 2 (output mode) 0x1C CCMR2_Input CCMR2_Input capture/compare mode register 2 (input mode) CCMR2_Output 0x1C CCER CCER capture/compare enable register 0x20 CNT CNT counter 0x24 CNT16 CNT16 16-bit counter register CNT 0x24 0x10 read-write 0x00000000 CNT counter value 0 16 read-write 0 65535 PSC PSC prescaler 0x28 ARR ARR auto-reload register 0x2C RCR RCR repetition counter register 0x30 4 0x4 1-4 CCR%s CCR%s capture/compare register 0x34 BDTR BDTR break and dead-time register 0x44 DCR DCR DMA control register 0x48 DMAR DMAR DMA address for full transfer 0x4C OR1 OR1 TIM8 option register 1 0x50 0x20 read-write 0x00000000 ETR_ADC2_RMP External trigger remap on ADC2 analog watchdog 0 2 ETR_ADC3_RMP External trigger remap on ADC3 analog watchdog 2 2 TI1_RMP Input Capture 1 remap 4 1 CCMR3_Output CCMR3_Output capture/compare mode register 2 (output mode) 0x54 CCR5 CCR5 capture/compare register 0x58 CCR6 CCR6 capture/compare register 0x5C OR2 OR2 TIM8 option register 2 0x60 0x20 read-write 0x00000001 BKINE BRK BKIN input enable 0 1 BKCMP1E BRK COMP1 enable 1 1 BKCMP2E BRK COMP2 enable 2 1 BKDFBK2E BRK DFSDM_BREAK[2] enable 8 1 BKINP BRK BKIN input polarity 9 1 BKCMP1P BRK COMP1 input polarity 10 1 BKCMP2P BRK COMP2 input polarity 11 1 ETRSEL ETR source selection 14 3 OR3 OR3 TIM8 option register 3 0x64 0x20 read-write 0x00000001 BK2INE BRK2 BKIN input enable 0 1 BK2CMP1E BRK2 COMP1 enable 1 1 BK2CMP2E BRK2 COMP2 enable 2 1 BK2DFBK3E BRK2 DFSDM_BREAK[3] enable 8 1 BK2INP BRK2 BKIN input polarity 9 1 BK2CMP1P BRK2 COMP1 input polarity 10 1 BK2CMP2P BRK2 COMP2 input polarity 11 1 TIM6 Basic-timers TIM 0x40001000 0x0 0x400 registers TIM6_DACUNDER TIM6 global and DAC1 and 2 underrun error interrupts 54 CR1 CR1 control register 1 0x0 0x10 read-write 0x00000000 UIFREMAP UIF status bit remapping 11 1 ARPE Auto-reload preload enable 7 1 ARPE Disabled TIMx_APRR register is not buffered 0 Enabled TIMx_APRR register is buffered 1 OPM One-pulse mode 3 1 OPM Disabled Counter is not stopped at update event 0 Enabled Counter stops counting at the next update event (clearing the CEN bit) 1 URS Update request source 2 1 URS AnyEvent Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request 0 CounterOnly Only counter overflow/underflow generates an update interrupt or DMA request 1 UDIS Update disable 1 1 UDIS Enabled Update event enabled 0 Disabled Update event disabled 1 CEN Counter enable 0 1 CEN Disabled Counter disabled 0 Enabled Counter enabled 1 CR2 CR2 control register 2 0x4 0x10 read-write 0x00000000 MMS Master mode selection 4 3 MMS Reset Use UG bit from TIMx_EGR register 0 Enable Use CNT bit from TIMx_CEN register 1 Update Use the update event 2 DIER DIER DMA/Interrupt enable register 0xC 0x10 read-write 0x00000000 UDE Update DMA request enable 8 1 UDE Disabled Update DMA request disabled 0 Enabled Update DMA request enabled 1 UIE Update interrupt enable 0 1 UIE Disabled Update interrupt disabled 0 Enabled Update interrupt enabled 1 SR SR status register 0x10 0x10 read-write 0x00000000 UIF Update interrupt flag 0 1 zeroToClear UIFR read NoUpdateOccurred No update occurred 0 UpdatePending Update interrupt pending 1 UIFW write Clear Clear flag 0 EGR EGR event generation register 0x14 0x20 write-only 0x00000000 UG Update generation 0 1 UG Update Re-initializes the timer counter and generates an update of the registers. 1 CNT CNT counter 0x24 0x20 0x00000000 UIFCPY UIF Copy 31 1 read-only CNT Low counter value 0 16 read-write 0 65535 CNT16 CNT16 16-bit counter register CNT 0x24 0x10 read-write 0x00000000 CNT counter value 0 16 read-write PSC PSC prescaler 0x28 0x10 read-write 0x00000000 PSC Prescaler value 0 16 0 65535 ARR ARR auto-reload register 0x2C 0x10 read-write 0x0000FFFF ARR Prescaler value 0 16 0 65535 TIM7 TIM 0x40001400 TIM7 TIM7 global interrupt 55 LPTIM1 Low power timer LPTIM 0x40007C00 0x0 0x400 registers LPTIM1 LP TIM1 interrupt 65 ISR ISR Interrupt and Status Register 0x0 0x20 read-only 0x00000000 DOWN Counter direction change up to down 6 1 DOWNR Set Counter direction change up to down 1 UP Counter direction change down to up 5 1 UPR Set Counter direction change down to up 1 ARROK Autoreload register update OK 4 1 ARROKR Set Autoreload register update OK 1 CMPOK Compare register update OK 3 1 CMPOKR Set Compare register update OK 1 EXTTRIG External trigger edge event 2 1 EXTTRIGR Set External trigger edge event 1 ARRM Autoreload match 1 1 ARRMR Set Autoreload match 1 CMPM Compare match 0 1 CMPMR Set Compare match 1 ICR ICR Interrupt Clear Register 0x4 0x20 write-only 0x00000000 DOWNCF Direction change to down Clear Flag 6 1 DOWNCFW Clear Direction change to down Clear Flag 1 UPCF Direction change to UP Clear Flag 5 1 UPCFW Clear Direction change to up Clear Flag 1 ARROKCF Autoreload register update OK Clear Flag 4 1 ARROKCFW Clear Autoreload register update OK Clear Flag 1 CMPOKCF Compare register update OK Clear Flag 3 1 CMPOKCFW Clear Compare register update OK Clear Flag 1 EXTTRIGCF External trigger valid edge Clear Flag 2 1 EXTTRIGCFW Clear External trigger valid edge Clear Flag 1 ARRMCF Autoreload match Clear Flag 1 1 ARRMCFW Clear Autoreload match Clear Flag 1 CMPMCF compare match Clear Flag 0 1 CMPMCFW Clear Compare match Clear Flag 1 IER IER Interrupt Enable Register 0x8 0x20 read-write 0x00000000 DOWNIE Direction change to down Interrupt Enable 6 1 DOWNIE Disabled DOWN interrupt disabled 0 Enabled DOWN interrupt enabled 1 UPIE Direction change to UP Interrupt Enable 5 1 UPIE Disabled UP interrupt disabled 0 Enabled UP interrupt enabled 1 ARROKIE Autoreload register update OK Interrupt Enable 4 1 ARROKIE Disabled ARROK interrupt disabled 0 Enabled ARROK interrupt enabled 1 CMPOKIE Compare register update OK Interrupt Enable 3 1 CMPOKIE Disabled CMPOK interrupt disabled 0 Enabled CMPOK interrupt enabled 1 EXTTRIGIE External trigger valid edge Interrupt Enable 2 1 EXTTRIGIE Disabled EXTTRIG interrupt disabled 0 Enabled EXTTRIG interrupt enabled 1 ARRMIE Autoreload match Interrupt Enable 1 1 ARRMIE Disabled ARRM interrupt disabled 0 Enabled ARRM interrupt enabled 1 CMPMIE Compare match Interrupt Enable 0 1 CMPMIE Disabled CMPM interrupt disabled 0 Enabled CMPM interrupt enabled 1 CFGR CFGR Configuration Register 0xC 0x20 read-write 0x00000000 ENC Encoder mode enable 24 1 ENC Disabled Encoder mode disabled 0 Enabled Encoder mode enabled 1 COUNTMODE counter mode enabled 23 1 COUNTMODE Internal The counter is incremented following each internal clock pulse 0 External The counter is incremented following each valid clock pulse on the LPTIM external Input1 1 PRELOAD Registers update mode 22 1 PRELOAD Immediate Registers are updated after each APB bus write access 0 EndOfPeriod Registers are updated at the end of the current LPTIM period 1 WAVPOL Waveform shape polarity 21 1 WAVPOL Positive The LPTIM output reflects the compare results between LPTIM_ARR and LPTIM_CMP registers 0 Negative The LPTIM output reflects the inverse of the compare results between LPTIM_ARR and LPTIM_CMP registers 1 WAVE Waveform shape 20 1 WAVE Inactive Deactivate Set-once mode, PWM / One Pulse waveform (depending on OPMODE bit) 0 Active Activate the Set-once mode 1 TIMOUT Timeout enable 19 1 TIMOUT Disabled A trigger event arriving when the timer is already started will be ignored 0 Enabled A trigger event arriving when the timer is already started will reset and restart the counter 1 TRIGEN Trigger enable and polarity 17 2 TRIGEN SW Software trigger (counting start is initiated by software) 0 RisingEdge Rising edge is the active edge 1 FallingEdge Falling edge is the active edge 2 BothEdges Both edges are active edges 3 TRIGSEL Trigger selector 13 3 TRIGSEL Trig0 lptim_ext_trig0 0 Trig1 lptim_ext_trig1 1 Trig2 lptim_ext_trig2 2 Trig3 lptim_ext_trig3 3 Trig4 lptim_ext_trig4 4 Trig5 lptim_ext_trig5 5 Trig6 lptim_ext_trig6 6 Trig7 lptim_ext_trig7 7 PRESC Clock prescaler 9 3 PRESC Div1 /1 0 Div2 /2 1 Div4 /4 2 Div8 /8 3 Div16 /16 4 Div32 /32 5 Div64 /64 6 Div128 /128 7 TRGFLT Configurable digital filter for trigger 6 2 TRGFLT Immediate Any trigger active level change is considered as a valid trigger 0 Clocks2 Trigger active level change must be stable for at least 2 clock periods before it is considered as valid trigger 1 Clocks4 Trigger active level change must be stable for at least 4 clock periods before it is considered as valid trigger 2 Clocks8 Trigger active level change must be stable for at least 8 clock periods before it is considered as valid trigger 3 CKFLT Configurable digital filter for external clock 3 2 CKFLT Immediate Any external clock signal level change is considered as a valid transition 0 Clocks2 External clock signal level change must be stable for at least 2 clock periods before it is considered as valid transition 1 Clocks4 External clock signal level change must be stable for at least 4 clock periods before it is considered as valid transition 2 Clocks8 External clock signal level change must be stable for at least 8 clock periods before it is considered as valid transition 3 CKPOL Clock Polarity 1 2 CKPOL RisingEdge The rising edge is the active edge used for counting. If LPTIM is in encoder mode: Encoder sub-mode 1 is active. 0 FallingEdge The falling edge is the active edge used for counting. If LPTIM is in encoder mode: Encoder sub-mode 2 is active. 1 BothEdges Both edges are active edge. If LPTIM is in encoder mode: Encoder sub-mode 3 is active. 2 CKSEL Clock selector 0 1 CKSEL Internal LPTIM is clocked by internal clock source (APB clock or any of the embedded oscillators) 0 External LPTIM is clocked by an external clock source through the LPTIM external Input1 1 CR CR Control Register 0x10 0x20 read-write 0x00000000 CNTSTRT Timer start in continuous mode 2 1 CNTSTRTW write Start Timer start in Continuous mode 1 SNGSTRT LPTIM start in single mode 1 1 SNGSTRTW write Start LPTIM start in Single mode 1 ENABLE LPTIM Enable 0 1 ENABLE Disabled LPTIM is disabled 0 Enabled LPTIM is enabled 1 CMP CMP Compare Register 0x14 0x20 read-write 0x00000000 CMP Compare value 0 16 0 65535 ARR ARR Autoreload Register 0x18 0x20 read-write 0x00000001 ARR Auto reload value 0 16 0 65535 CNT CNT Counter Register 0x1C 0x20 read-only 0x00000000 CNT Counter value 0 16 0 65535 LPTIM2 0x40009400 LPTIM2 LP TIM2 interrupt 66 USART1 Universal synchronous asynchronous receiver transmitter USART 0x40013800 0x0 0x400 registers USART1 USART1 global interrupt 37 CR1 CR1 Control register 1 0x0 0x20 read-write 0x00000000 M1 Word length 28 1 M1 M0 Use M0 to set the data bits 0 Bit7 1 start bit, 7 data bits, n stop bits 1 EOBIE End of Block interrupt enable 27 1 EOBIE Disabled Interrupt is inhibited 0 Enabled A USART interrupt is generated when the EOBF flag is set in the ISR register 1 RTOIE Receiver timeout interrupt enable 26 1 RTOIE Disabled Interrupt is inhibited 0 Enabled An USART interrupt is generated when the RTOF bit is set in the ISR register 1 DEAT Driver Enable assertion time 21 5 0 31 DEDT Driver Enable de-assertion time 16 5 0 31 OVER8 Oversampling mode 15 1 OVER8 Oversampling16 Oversampling by 16 0 Oversampling8 Oversampling by 8 1 CMIE Character match interrupt enable 14 1 CMIE Disabled Interrupt is disabled 0 Enabled Interrupt is generated when the CMF bit is set in the ISR register 1 MME Mute mode enable 13 1 MME Disabled Receiver in active mode permanently 0 Enabled Receiver can switch between mute mode and active mode 1 M0 Word length 12 1 M0 Bit8 1 start bit, 8 data bits, n stop bits 0 Bit9 1 start bit, 9 data bits, n stop bits 1 WAKE Receiver wakeup method 11 1 WAKE Idle Idle line 0 Address Address mask 1 PCE Parity control enable 10 1 PCE Disabled Parity control disabled 0 Enabled Parity control enabled 1 PS Parity selection 9 1 PS Even Even parity 0 Odd Odd parity 1 PEIE PE interrupt enable 8 1 PEIE Disabled Interrupt is disabled 0 Enabled Interrupt is generated whenever PE=1 in the ISR register 1 TXEIE interrupt enable 7 1 TXEIE Disabled Interrupt is disabled 0 Enabled Interrupt is generated whenever TXE=1 in the ISR register 1 TCIE Transmission complete interrupt enable 6 1 TCIE Disabled Interrupt is disabled 0 Enabled Interrupt is generated whenever TC=1 in the ISR register 1 RXNEIE RXNE interrupt enable 5 1 RXNEIE Disabled Interrupt is disabled 0 Enabled Interrupt is generated whenever ORE=1 or RXNE=1 in the ISR register 1 IDLEIE IDLE interrupt enable 4 1 IDLEIE Disabled Interrupt is disabled 0 Enabled Interrupt is generated whenever IDLE=1 in the ISR register 1 TE Transmitter enable 3 1 TE Disabled Transmitter is disabled 0 Enabled Transmitter is enabled 1 RE Receiver enable 2 1 RE Disabled Receiver is disabled 0 Enabled Receiver is enabled 1 UESM USART enable in Stop mode 1 1 UESM Disabled USART not able to wake up the MCU from Stop mode 0 Enabled USART able to wake up the MCU from Stop mode 1 UE USART enable 0 1 UE Disabled UART is disabled 0 Enabled UART is enabled 1 CR2 CR2 Control register 2 0x4 0x20 read-write 0x00000000 ADD Address of the USART node 24 8 0 255 RTOEN Receiver timeout enable 23 1 RTOEN Disabled Receiver timeout feature disabled 0 Enabled Receiver timeout feature enabled 1 ABRMOD Auto baud rate mode 21 2 ABRMOD Start Measurement of the start bit is used to detect the baud rate 0 Edge Falling edge to falling edge measurement 1 Frame7F 0x7F frame detection 2 Frame55 0x55 frame detection 3 ABREN Auto baud rate enable 20 1 ABREN Disabled Auto baud rate detection is disabled 0 Enabled Auto baud rate detection is enabled 1 MSBFIRST Most significant bit first 19 1 MSBFIRST LSB data is transmitted/received with data bit 0 first, following the start bit 0 MSB data is transmitted/received with MSB (bit 7/8/9) first, following the start bit 1 DATAINV Binary data inversion 18 1 DATAINV Positive Logical data from the data register are send/received in positive/direct logic 0 Negative Logical data from the data register are send/received in negative/inverse logic 1 TXINV TX pin active level inversion 17 1 TXINV Standard TX pin signal works using the standard logic levels 0 Inverted TX pin signal values are inverted 1 RXINV RX pin active level inversion 16 1 RXINV Standard RX pin signal works using the standard logic levels 0 Inverted RX pin signal values are inverted 1 SWAP Swap TX/RX pins 15 1 SWAP Standard TX/RX pins are used as defined in standard pinout 0 Swapped The TX and RX pins functions are swapped 1 LINEN LIN mode enable 14 1 LINEN Disabled LIN mode disabled 0 Enabled LIN mode enabled 1 STOP STOP bits 12 2 STOP Stop1 1 stop bit 0 Stop0p5 0.5 stop bit 1 Stop2 2 stop bit 2 Stop1p5 1.5 stop bit 3 CLKEN Clock enable 11 1 CLKEN Disabled CK pin disabled 0 Enabled CK pin enabled 1 CPOL Clock polarity 10 1 CPOL Low Steady low value on CK pin outside transmission window 0 High Steady high value on CK pin outside transmission window 1 CPHA Clock phase 9 1 CPHA First The first clock transition is the first data capture edge 0 Second The second clock transition is the first data capture edge 1 LBCL Last bit clock pulse 8 1 LBCL NotOutput The clock pulse of the last data bit is not output to the CK pin 0 Output The clock pulse of the last data bit is output to the CK pin 1 LBDIE LIN break detection interrupt enable 6 1 LBDIE Disabled Interrupt is inhibited 0 Enabled An interrupt is generated whenever LBDF=1 in the ISR register 1 LBDL LIN break detection length 5 1 LBDL Bit10 10-bit break detection 0 Bit11 11-bit break detection 1 ADDM7 7-bit Address Detection/4-bit Address Detection 4 1 ADDM7 Bit4 4-bit address detection 0 Bit7 7-bit address detection 1 CR3 CR3 Control register 3 0x8 0x20 read-write 0x00000000 WUFIE Wakeup from Stop mode interrupt enable 22 1 WUFIE Disabled Interrupt is inhibited 0 Enabled An USART interrupt is generated whenever WUF=1 in the ISR register 1 WUS Wakeup from Stop mode interrupt flag selection 20 2 WUS Address WUF active on address match 0 Start WuF active on Start bit detection 2 RXNE WUF active on RXNE 3 SCARCNT Smartcard auto-retry count 17 3 0 7 DEP Driver enable polarity selection 15 1 DEP High DE signal is active high 0 Low DE signal is active low 1 DEM Driver enable mode 14 1 DEM Disabled DE function is disabled 0 Enabled The DE signal is output on the RTS pin 1 DDRE DMA Disable on Reception Error 13 1 DDRE NotDisabled DMA is not disabled in case of reception error 0 Disabled DMA is disabled following a reception error 1 OVRDIS Overrun Disable 12 1 OVRDIS Enabled Overrun Error Flag, ORE, is set when received data is not read before receiving new data 0 Disabled Overrun functionality is disabled. If new data is received while the RXNE flag is still set the ORE flag is not set and the new received data overwrites the previous content of the RDR register 1 ONEBIT One sample bit method enable 11 1 ONEBIT Sample3 Three sample bit method 0 Sample1 One sample bit method 1 CTSIE CTS interrupt enable 10 1 CTSIE Disabled Interrupt is inhibited 0 Enabled An interrupt is generated whenever CTSIF=1 in the ISR register 1 CTSE CTS enable 9 1 CTSE Disabled CTS hardware flow control disabled 0 Enabled CTS mode enabled, data is only transmitted when the CTS input is asserted 1 RTSE RTS enable 8 1 RTSE Disabled RTS hardware flow control disabled 0 Enabled RTS output enabled, data is only requested when there is space in the receive buffer 1 DMAT DMA enable transmitter 7 1 DMAT Disabled DMA mode is disabled for transmission 0 Enabled DMA mode is enabled for transmission 1 DMAR DMA enable receiver 6 1 DMAR Disabled DMA mode is disabled for reception 0 Enabled DMA mode is enabled for reception 1 SCEN Smartcard mode enable 5 1 SCEN Disabled Smartcard Mode disabled 0 Enabled Smartcard Mode enabled 1 NACK Smartcard NACK enable 4 1 NACK Disabled NACK transmission in case of parity error is disabled 0 Enabled NACK transmission during parity error is enabled 1 HDSEL Half-duplex selection 3 1 HDSEL NotSelected Half duplex mode is not selected 0 Selected Half duplex mode is selected 1 IRLP Ir low-power 2 1 IRLP Normal Normal mode 0 LowPower Low-power mode 1 IREN Ir mode enable 1 1 IREN Disabled IrDA disabled 0 Enabled IrDA enabled 1 EIE Error interrupt enable 0 1 EIE Disabled Interrupt is inhibited 0 Enabled An interrupt is generated when FE=1 or ORE=1 or NF=1 in the ISR register 1 UCESM USART Clock Enable in Stop mode. 23 1 TCBGTIE Transmission complete before guard time interrupt enable 24 1 BRR BRR Baud rate register 0xC 0x20 read-write 0x00000000 BRR DIV_Mantissa 0 16 0 65535 GTPR GTPR Guard time and prescaler register 0x10 0x20 read-write 0x00000000 GT Guard time value 8 8 0 255 PSC Prescaler value 0 8 0 255 RTOR RTOR Receiver timeout register 0x14 0x20 read-write 0x00000000 BLEN Block Length 24 8 0 255 RTO Receiver timeout value 0 24 0 16777215 RQR RQR Request register 0x18 0x20 write-only 0x00000000 TXFRQ Transmit data flush request 4 1 TXFRQ Discard Set the TXE flags. This allows to discard the transmit data 1 RXFRQ Receive data flush request 3 1 RXFRQ Discard clears the RXNE flag. This allows to discard the received data without reading it, and avoid an overrun condition 1 MMRQ Mute mode request 2 1 MMRQ Mute Puts the USART in mute mode and sets the RWU flag 1 SBKRQ Send break request 1 1 SBKRQ Break sets the SBKF flag and request to send a BREAK on the line, as soon as the transmit machine is available 1 ABRRQ Auto baud rate request 0 1 ABRRQ Request resets the ABRF flag in the USART_ISR and request an automatic baud rate measurement on the next received data frame 1 ISR ISR Interrupt & status register 0x1C 0x20 read-only 0x020000C0 REACK REACK 22 1 TEACK TEACK 21 1 WUF WUF 20 1 RWU RWU 19 1 RWU Active Receiver in Active mode 0 Mute Receiver in Mute mode 1 SBKF SBKF 18 1 SBKF NoBreak No break character transmitted 0 Break Break character transmitted 1 CMF CMF 17 1 CMF NoMatch No Character match detected 0 Match Character match detected 1 BUSY BUSY 16 1 BUSY Idle USART is idle (no reception) 0 Busy Reception on going 1 ABRF ABRF 15 1 ABRE ABRE 14 1 EOBF EOBF 12 1 EOBF NotReached End of Block not reached 0 Reached End of Block (number of characters) reached 1 RTOF RTOF 11 1 RTOF NotReached Timeout value not reached 0 Reached Timeout value reached without any data reception 1 CTS CTS 10 1 CTS Set CTS line set 0 Reset CTS line reset 1 CTSIF CTSIF 9 1 CTSIF NotChanged No change occurred on the CTS status line 0 Changed A change occurred on the CTS status line 1 LBDF LBDF 8 1 LBDF NotDetected LIN break not detected 0 Detected LIN break detected 1 TXE TXE 7 1 TXE Full Transmit FIFO is full 0 NotFull Transmit FIFO is not full 1 TC TC 6 1 TC TxNotComplete Transmission is not complete 0 TxComplete Transmission is complete 1 RXNE RXNE 5 1 RXNE NoData Data is not received 0 DataReady Received data is ready to be read 1 IDLE IDLE 4 1 IDLE NoIdle No Idle Line is detected 0 Idle Idle Line is detected 1 ORE ORE 3 1 ORE NoOverrun No Overrun error 0 Overrun Overrun error is detected 1 NF NF 2 1 NF NoNoise No noise is detected 0 Noise Noise is detected 1 FE FE 1 1 FE NoError No Framing error is detected 0 Error Framing error or break character is detected 1 PE PE 0 1 PE NoError No parity error 0 Error Parity error 1 ICR ICR Interrupt flag clear register 0x20 0x20 write-only 0x00000000 WUCF Wakeup from Stop mode clear flag 20 1 oneToClear WUCF Clear Clears the WUF flag in the ISR register 1 CMCF Character match clear flag 17 1 oneToClear CMCF Clear Clears the CMF flag in the ISR register 1 EOBCF End of block clear flag 12 1 oneToClear EOBCF Clear Clears the EOBF flag in the ISR register 1 RTOCF Receiver timeout clear flag 11 1 oneToClear RTOCF Clear Clears the RTOF flag in the ISR register 1 CTSCF CTS clear flag 9 1 oneToClear CTSCF Clear Clears the CTSIF flag in the ISR register 1 LBDCF LIN break detection clear flag 8 1 oneToClear LBDCF Clear Clears the LBDF flag in the ISR register 1 TCCF Transmission complete clear flag 6 1 oneToClear TCCF Clear Clears the TC flag in the ISR register 1 IDLECF Idle line detected clear flag 4 1 oneToClear IDLECF Clear Clears the IDLE flag in the ISR register 1 ORECF Overrun error clear flag 3 1 oneToClear ORECF Clear Clears the ORE flag in the ISR register 1 NCF Noise detected clear flag 2 1 oneToClear NCF Clear Clears the NF flag in the ISR register 1 FECF Framing error clear flag 1 1 oneToClear FECF Clear Clears the FE flag in the ISR register 1 PECF Parity error clear flag 0 1 oneToClear PECF Clear Clears the PE flag in the ISR register 1 RDR RDR Receive data register 0x24 0x20 read-only 0x00000000 RDR Receive data value 0 9 0 511 TDR TDR Transmit data register 0x28 0x20 read-write 0x00000000 TDR Transmit data value 0 9 0 511 USART2 Universal synchronous asynchronous receiver transmitter USART 0x40004400 USART2 USART2 global interrupt 38 USART3 Universal synchronous asynchronous receiver transmitter USART 0x40004800 USART3 USART3 global interrupt 39 UART4 Universal synchronous asynchronous receiver transmitter USART 0x40004C00 0x0 0x400 registers UART4 UART4 global Interrupt 52 CR1 CR1 Control register 1 0x0 0x20 read-write 0x00000000 M1 Word length 28 1 M1 M0 Use M0 to set the data bits 0 Bit7 1 start bit, 7 data bits, n stop bits 1 EOBIE End of Block interrupt enable 27 1 EOBIE Disabled Interrupt is inhibited 0 Enabled A USART interrupt is generated when the EOBF flag is set in the ISR register 1 RTOIE Receiver timeout interrupt enable 26 1 RTOIE Disabled Interrupt is inhibited 0 Enabled An USART interrupt is generated when the RTOF bit is set in the ISR register 1 DEAT Driver Enable assertion time 21 5 0 31 DEDT Driver Enable de-assertion time 16 5 0 31 OVER8 Oversampling mode 15 1 OVER8 Oversampling16 Oversampling by 16 0 Oversampling8 Oversampling by 8 1 CMIE Character match interrupt enable 14 1 CMIE Disabled Interrupt is disabled 0 Enabled Interrupt is generated when the CMF bit is set in the ISR register 1 MME Mute mode enable 13 1 MME Disabled Receiver in active mode permanently 0 Enabled Receiver can switch between mute mode and active mode 1 M0 Word length 12 1 M0 Bit8 1 start bit, 8 data bits, n stop bits 0 Bit9 1 start bit, 9 data bits, n stop bits 1 WAKE Receiver wakeup method 11 1 WAKE Idle Idle line 0 Address Address mask 1 PCE Parity control enable 10 1 PCE Disabled Parity control disabled 0 Enabled Parity control enabled 1 PS Parity selection 9 1 PS Even Even parity 0 Odd Odd parity 1 PEIE PE interrupt enable 8 1 PEIE Disabled Interrupt is disabled 0 Enabled Interrupt is generated whenever PE=1 in the ISR register 1 TXEIE interrupt enable 7 1 TXEIE Disabled Interrupt is disabled 0 Enabled Interrupt is generated whenever TXE=1 in the ISR register 1 TCIE Transmission complete interrupt enable 6 1 TCIE Disabled Interrupt is disabled 0 Enabled Interrupt is generated whenever TC=1 in the ISR register 1 RXNEIE RXNE interrupt enable 5 1 RXNEIE Disabled Interrupt is disabled 0 Enabled Interrupt is generated whenever ORE=1 or RXNE=1 in the ISR register 1 IDLEIE IDLE interrupt enable 4 1 IDLEIE Disabled Interrupt is disabled 0 Enabled Interrupt is generated whenever IDLE=1 in the ISR register 1 TE Transmitter enable 3 1 TE Disabled Transmitter is disabled 0 Enabled Transmitter is enabled 1 RE Receiver enable 2 1 RE Disabled Receiver is disabled 0 Enabled Receiver is enabled 1 UESM USART enable in Stop mode 1 1 UESM Disabled USART not able to wake up the MCU from Stop mode 0 Enabled USART able to wake up the MCU from Stop mode 1 UE USART enable 0 1 UE Disabled UART is disabled 0 Enabled UART is enabled 1 CR2 CR2 Control register 2 0x4 0x20 read-write 0x00000000 RTOEN Receiver timeout enable 23 1 RTOEN Disabled Receiver timeout feature disabled 0 Enabled Receiver timeout feature enabled 1 ABRMOD Auto baud rate mode 21 2 ABRMOD Start Measurement of the start bit is used to detect the baud rate 0 Edge Falling edge to falling edge measurement 1 Frame7F 0x7F frame detection 2 Frame55 0x55 frame detection 3 ABREN Auto baud rate enable 20 1 ABREN Disabled Auto baud rate detection is disabled 0 Enabled Auto baud rate detection is enabled 1 MSBFIRST Most significant bit first 19 1 MSBFIRST LSB data is transmitted/received with data bit 0 first, following the start bit 0 MSB data is transmitted/received with MSB (bit 7/8/9) first, following the start bit 1 DATAINV Binary data inversion 18 1 DATAINV Positive Logical data from the data register are send/received in positive/direct logic 0 Negative Logical data from the data register are send/received in negative/inverse logic 1 TXINV TX pin active level inversion 17 1 TXINV Standard TX pin signal works using the standard logic levels 0 Inverted TX pin signal values are inverted 1 RXINV RX pin active level inversion 16 1 RXINV Standard RX pin signal works using the standard logic levels 0 Inverted RX pin signal values are inverted 1 SWAP Swap TX/RX pins 15 1 SWAP Standard TX/RX pins are used as defined in standard pinout 0 Swapped The TX and RX pins functions are swapped 1 LINEN LIN mode enable 14 1 LINEN Disabled LIN mode disabled 0 Enabled LIN mode enabled 1 STOP STOP bits 12 2 STOP Stop1 1 stop bit 0 Stop0p5 0.5 stop bit 1 Stop2 2 stop bit 2 Stop1p5 1.5 stop bit 3 CLKEN Clock enable 11 1 CLKEN Disabled CK pin disabled 0 Enabled CK pin enabled 1 CPOL Clock polarity 10 1 CPOL Low Steady low value on CK pin outside transmission window 0 High Steady high value on CK pin outside transmission window 1 CPHA Clock phase 9 1 CPHA First The first clock transition is the first data capture edge 0 Second The second clock transition is the first data capture edge 1 LBCL Last bit clock pulse 8 1 LBCL NotOutput The clock pulse of the last data bit is not output to the CK pin 0 Output The clock pulse of the last data bit is output to the CK pin 1 LBDIE LIN break detection interrupt enable 6 1 LBDIE Disabled Interrupt is inhibited 0 Enabled An interrupt is generated whenever LBDF=1 in the ISR register 1 LBDL LIN break detection length 5 1 LBDL Bit10 10-bit break detection 0 Bit11 11-bit break detection 1 ADDM7 7-bit Address Detection/4-bit Address Detection 4 1 ADDM7 Bit4 4-bit address detection 0 Bit7 7-bit address detection 1 ADD Address of the USART node 24 8 0 255 CR3 CR3 Control register 3 0x8 0x20 read-write 0x00000000 WUFIE Wakeup from Stop mode interrupt enable 22 1 WUFIE Disabled Interrupt is inhibited 0 Enabled An USART interrupt is generated whenever WUF=1 in the ISR register 1 WUS Wakeup from Stop mode interrupt flag selection 20 2 WUS Address WUF active on address match 0 Start WuF active on Start bit detection 2 RXNE WUF active on RXNE 3 SCARCNT Smartcard auto-retry count 17 3 0 7 DEP Driver enable polarity selection 15 1 DEP High DE signal is active high 0 Low DE signal is active low 1 DEM Driver enable mode 14 1 DEM Disabled DE function is disabled 0 Enabled The DE signal is output on the RTS pin 1 DDRE DMA Disable on Reception Error 13 1 DDRE NotDisabled DMA is not disabled in case of reception error 0 Disabled DMA is disabled following a reception error 1 OVRDIS Overrun Disable 12 1 OVRDIS Enabled Overrun Error Flag, ORE, is set when received data is not read before receiving new data 0 Disabled Overrun functionality is disabled. If new data is received while the RXNE flag is still set the ORE flag is not set and the new received data overwrites the previous content of the RDR register 1 ONEBIT One sample bit method enable 11 1 ONEBIT Sample3 Three sample bit method 0 Sample1 One sample bit method 1 CTSIE CTS interrupt enable 10 1 CTSIE Disabled Interrupt is inhibited 0 Enabled An interrupt is generated whenever CTSIF=1 in the ISR register 1 CTSE CTS enable 9 1 CTSE Disabled CTS hardware flow control disabled 0 Enabled CTS mode enabled, data is only transmitted when the CTS input is asserted 1 RTSE RTS enable 8 1 RTSE Disabled RTS hardware flow control disabled 0 Enabled RTS output enabled, data is only requested when there is space in the receive buffer 1 DMAT DMA enable transmitter 7 1 DMAT Disabled DMA mode is disabled for transmission 0 Enabled DMA mode is enabled for transmission 1 DMAR DMA enable receiver 6 1 DMAR Disabled DMA mode is disabled for reception 0 Enabled DMA mode is enabled for reception 1 SCEN Smartcard mode enable 5 1 SCEN Disabled Smartcard Mode disabled 0 Enabled Smartcard Mode enabled 1 NACK Smartcard NACK enable 4 1 NACK Disabled NACK transmission in case of parity error is disabled 0 Enabled NACK transmission during parity error is enabled 1 HDSEL Half-duplex selection 3 1 HDSEL NotSelected Half duplex mode is not selected 0 Selected Half duplex mode is selected 1 IRLP Ir low-power 2 1 IRLP Normal Normal mode 0 LowPower Low-power mode 1 IREN Ir mode enable 1 1 IREN Disabled IrDA disabled 0 Enabled IrDA enabled 1 EIE Error interrupt enable 0 1 EIE Disabled Interrupt is inhibited 0 Enabled An interrupt is generated when FE=1 or ORE=1 or NF=1 in the ISR register 1 BRR BRR Baud rate register 0xC 0x20 read-write 0x00000000 BRR DIV_Mantissa 0 16 0 65535 GTPR GTPR Guard time and prescaler register 0x10 0x20 read-write 0x00000000 GT Guard time value 8 8 0 255 PSC Prescaler value 0 8 0 255 RTOR RTOR Receiver timeout register 0x14 0x20 read-write 0x00000000 BLEN Block Length 24 8 0 255 RTO Receiver timeout value 0 24 0 16777215 RQR RQR Request register 0x18 0x20 write-only 0x00000000 TXFRQ Transmit data flush request 4 1 TXFRQ Discard Set the TXE flags. This allows to discard the transmit data 1 RXFRQ Receive data flush request 3 1 RXFRQ Discard clears the RXNE flag. This allows to discard the received data without reading it, and avoid an overrun condition 1 MMRQ Mute mode request 2 1 MMRQ Mute Puts the USART in mute mode and sets the RWU flag 1 SBKRQ Send break request 1 1 SBKRQ Break sets the SBKF flag and request to send a BREAK on the line, as soon as the transmit machine is available 1 ABRRQ Auto baud rate request 0 1 ABRRQ Request resets the ABRF flag in the USART_ISR and request an automatic baud rate measurement on the next received data frame 1 ISR ISR Interrupt & status register 0x1C 0x20 read-only 0x020000C0 REACK REACK 22 1 TEACK TEACK 21 1 WUF WUF 20 1 RWU RWU 19 1 RWU Active Receiver in Active mode 0 Mute Receiver in Mute mode 1 SBKF SBKF 18 1 SBKF NoBreak No break character transmitted 0 Break Break character transmitted 1 CMF CMF 17 1 CMF NoMatch No Character match detected 0 Match Character match detected 1 BUSY BUSY 16 1 BUSY Idle USART is idle (no reception) 0 Busy Reception on going 1 ABRF ABRF 15 1 ABRE ABRE 14 1 EOBF EOBF 12 1 EOBF NotReached End of Block not reached 0 Reached End of Block (number of characters) reached 1 RTOF RTOF 11 1 RTOF NotReached Timeout value not reached 0 Reached Timeout value reached without any data reception 1 CTS CTS 10 1 CTS Set CTS line set 0 Reset CTS line reset 1 CTSIF CTSIF 9 1 CTSIF NotChanged No change occurred on the CTS status line 0 Changed A change occurred on the CTS status line 1 LBDF LBDF 8 1 LBDF NotDetected LIN break not detected 0 Detected LIN break detected 1 TXE TXE 7 1 TXE Full Transmit FIFO is full 0 NotFull Transmit FIFO is not full 1 TC TC 6 1 TC TxNotComplete Transmission is not complete 0 TxComplete Transmission is complete 1 RXNE RXNE 5 1 RXNE NoData Data is not received 0 DataReady Received data is ready to be read 1 IDLE IDLE 4 1 IDLE NoIdle No Idle Line is detected 0 Idle Idle Line is detected 1 ORE ORE 3 1 ORE NoOverrun No Overrun error 0 Overrun Overrun error is detected 1 NF NF 2 1 NF NoNoise No noise is detected 0 Noise Noise is detected 1 FE FE 1 1 FE NoError No Framing error is detected 0 Error Framing error or break character is detected 1 PE PE 0 1 PE NoError No parity error 0 Error Parity error 1 ICR ICR Interrupt flag clear register 0x20 0x20 write-only 0x00000000 WUCF Wakeup from Stop mode clear flag 20 1 oneToClear WUCF Clear Clears the WUF flag in the ISR register 1 CMCF Character match clear flag 17 1 oneToClear CMCF Clear Clears the CMF flag in the ISR register 1 EOBCF End of block clear flag 12 1 oneToClear EOBCF Clear Clears the EOBF flag in the ISR register 1 RTOCF Receiver timeout clear flag 11 1 oneToClear RTOCF Clear Clears the RTOF flag in the ISR register 1 CTSCF CTS clear flag 9 1 oneToClear CTSCF Clear Clears the CTSIF flag in the ISR register 1 LBDCF LIN break detection clear flag 8 1 oneToClear LBDCF Clear Clears the LBDF flag in the ISR register 1 TCCF Transmission complete clear flag 6 1 oneToClear TCCF Clear Clears the TC flag in the ISR register 1 IDLECF Idle line detected clear flag 4 1 oneToClear IDLECF Clear Clears the IDLE flag in the ISR register 1 ORECF Overrun error clear flag 3 1 oneToClear ORECF Clear Clears the ORE flag in the ISR register 1 NCF Noise detected clear flag 2 1 oneToClear NCF Clear Clears the NF flag in the ISR register 1 FECF Framing error clear flag 1 1 oneToClear FECF Clear Clears the FE flag in the ISR register 1 PECF Parity error clear flag 0 1 oneToClear PECF Clear Clears the PE flag in the ISR register 1 RDR RDR Receive data register 0x24 0x20 read-only 0x00000000 RDR Receive data value 0 9 0 511 TDR TDR Transmit data register 0x28 0x20 read-write 0x00000000 TDR Transmit data value 0 9 0 511 UART5 0x40005000 UART5 UART5 global Interrupt 53 LPUART1 Universal synchronous asynchronous receiver transmitter USART 0x40008000 0x0 0x400 registers LPUART1 LPUART1 global interrupt 70 CR1 CR1 Control register 1 0x0 0x20 read-write 0x00000000 M1 Word length 28 1 M1 M0 Use M0 to set the data bits 0 Bit7 1 start bit, 7 data bits, n stop bits 1 DEAT Driver Enable assertion time 21 5 0 31 DEDT Driver Enable de-assertion time 16 5 0 31 CMIE Character match interrupt enable 14 1 CMIE Disabled Interrupt is disabled 0 Enabled Interrupt is generated when the CMF bit is set in the ISR register 1 MME Mute mode enable 13 1 MME Disabled Receiver in active mode permanently 0 Enabled Receiver can switch between mute mode and active mode 1 M0 Word length 12 1 M0 Bit8 1 start bit, 8 data bits, n stop bits 0 Bit9 1 start bit, 9 data bits, n stop bits 1 WAKE Receiver wakeup method 11 1 WAKE Idle Idle line 0 Address Address mask 1 PCE Parity control enable 10 1 PCE Disabled Parity control disabled 0 Enabled Parity control enabled 1 PS Parity selection 9 1 PS Even Even parity 0 Odd Odd parity 1 PEIE PE interrupt enable 8 1 PEIE Disabled Interrupt is disabled 0 Enabled Interrupt is generated whenever PE=1 in the ISR register 1 TXEIE interrupt enable 7 1 TXEIE Disabled Interrupt is disabled 0 Enabled Interrupt is generated whenever TXE=1 in the ISR register 1 TCIE Transmission complete interrupt enable 6 1 TCIE Disabled Interrupt is disabled 0 Enabled Interrupt is generated whenever TC=1 in the ISR register 1 RXNEIE RXNE interrupt enable 5 1 RXNEIE Disabled Interrupt is disabled 0 Enabled Interrupt is generated whenever ORE=1 or RXNE=1 in the ISR register 1 IDLEIE IDLE interrupt enable 4 1 IDLEIE Disabled Interrupt is disabled 0 Enabled Interrupt is generated whenever IDLE=1 in the ISR register 1 TE Transmitter enable 3 1 TE Disabled Transmitter is disabled 0 Enabled Transmitter is enabled 1 RE Receiver enable 2 1 RE Disabled Receiver is disabled 0 Enabled Receiver is enabled 1 UESM USART enable in Stop mode 1 1 UESM Disabled USART not able to wake up the MCU from Stop mode 0 Enabled USART able to wake up the MCU from Stop mode 1 UE USART enable 0 1 UE Disabled UART is disabled 0 Enabled UART is enabled 1 CR2 CR2 Control register 2 0x4 0x20 read-write 0x00000000 ADD Address of the USART node 24 8 0 255 MSBFIRST Most significant bit first 19 1 MSBFIRST LSB data is transmitted/received with data bit 0 first, following the start bit 0 MSB data is transmitted/received with MSB (bit 7/8/9) first, following the start bit 1 DATAINV Binary data inversion 18 1 DATAINV Positive Logical data from the data register are send/received in positive/direct logic 0 Negative Logical data from the data register are send/received in negative/inverse logic 1 TXINV TX pin active level inversion 17 1 TXINV Standard TX pin signal works using the standard logic levels 0 Inverted TX pin signal values are inverted 1 RXINV RX pin active level inversion 16 1 RXINV Standard RX pin signal works using the standard logic levels 0 Inverted RX pin signal values are inverted 1 SWAP Swap TX/RX pins 15 1 SWAP Standard TX/RX pins are used as defined in standard pinout 0 Swapped The TX and RX pins functions are swapped 1 STOP STOP bits 12 2 STOP Stop1 1 stop bit 0 Stop0p5 0.5 stop bit 1 Stop2 2 stop bit 2 Stop1p5 1.5 stop bit 3 CLKEN Clock enable 11 1 CLKEN Disabled CK pin disabled 0 Enabled CK pin enabled 1 ADDM7 7-bit Address Detection/4-bit Address Detection 4 1 ADDM7 Bit4 4-bit address detection 0 Bit7 7-bit address detection 1 CR3 CR3 Control register 3 0x8 0x20 read-write 0x00000000 WUFIE Wakeup from Stop mode interrupt enable 22 1 WUFIE Disabled Interrupt is inhibited 0 Enabled An USART interrupt is generated whenever WUF=1 in the ISR register 1 WUS Wakeup from Stop mode interrupt flag selection 20 2 WUS Address WUF active on address match 0 Start WuF active on Start bit detection 2 RXNE WUF active on RXNE 3 DEP Driver enable polarity selection 15 1 DEP High DE signal is active high 0 Low DE signal is active low 1 DEM Driver enable mode 14 1 DEM Disabled DE function is disabled 0 Enabled The DE signal is output on the RTS pin 1 DDRE DMA Disable on Reception Error 13 1 DDRE NotDisabled DMA is not disabled in case of reception error 0 Disabled DMA is disabled following a reception error 1 OVRDIS Overrun Disable 12 1 OVRDIS Enabled Overrun Error Flag, ORE, is set when received data is not read before receiving new data 0 Disabled Overrun functionality is disabled. If new data is received while the RXNE flag is still set the ORE flag is not set and the new received data overwrites the previous content of the RDR register 1 CTSIE CTS interrupt enable 10 1 CTSIE Disabled Interrupt is inhibited 0 Enabled An interrupt is generated whenever CTSIF=1 in the ISR register 1 CTSE CTS enable 9 1 CTSE Disabled CTS hardware flow control disabled 0 Enabled CTS mode enabled, data is only transmitted when the CTS input is asserted 1 RTSE RTS enable 8 1 RTSE Disabled RTS hardware flow control disabled 0 Enabled RTS output enabled, data is only requested when there is space in the receive buffer 1 DMAT DMA enable transmitter 7 1 DMAT Disabled DMA mode is disabled for transmission 0 Enabled DMA mode is enabled for transmission 1 DMAR DMA enable receiver 6 1 DMAR Disabled DMA mode is disabled for reception 0 Enabled DMA mode is enabled for reception 1 HDSEL Half-duplex selection 3 1 HDSEL NotSelected Half duplex mode is not selected 0 Selected Half duplex mode is selected 1 EIE Error interrupt enable 0 1 EIE Disabled Interrupt is inhibited 0 Enabled An interrupt is generated when FE=1 or ORE=1 or NF=1 in the ISR register 1 UCESM_ LPUART Clock Enable in Stop mode 23 1 BRR BRR Baud rate register 0xC 0x20 read-write 0x00000000 BRR BRR 0 20 0 1048575 RQR RQR Request register 0x18 0x20 write-only 0x00000000 RXFRQ Receive data flush request 3 1 RXFRQ Discard clears the RXNE flag. This allows to discard the received data without reading it, and avoid an overrun condition 1 MMRQ Mute mode request 2 1 MMRQ Mute Puts the USART in mute mode and sets the RWU flag 1 SBKRQ Send break request 1 1 SBKRQ Break sets the SBKF flag and request to send a BREAK on the line, as soon as the transmit machine is available 1 ISR ISR Interrupt & status register 0x1C 0x20 read-only 0x020000C0 REACK REACK 22 1 TEACK TEACK 21 1 WUF WUF 20 1 RWU RWU 19 1 RWU Active Receiver in Active mode 0 Mute Receiver in Mute mode 1 SBKF SBKF 18 1 SBKF NoBreak No break character transmitted 0 Break Break character transmitted 1 CMF CMF 17 1 CMF NoMatch No Character match detected 0 Match Character match detected 1 BUSY BUSY 16 1 BUSY Idle USART is idle (no reception) 0 Busy Reception on going 1 CTS CTS 10 1 CTS Set CTS line set 0 Reset CTS line reset 1 CTSIF CTSIF 9 1 CTSIF NotChanged No change occurred on the CTS status line 0 Changed A change occurred on the CTS status line 1 TXE TXE 7 1 TXE Full Transmit FIFO is full 0 NotFull Transmit FIFO is not full 1 TC TC 6 1 TC TxNotComplete Transmission is not complete 0 TxComplete Transmission is complete 1 RXNE RXNE 5 1 RXNE NoData Data is not received 0 DataReady Received data is ready to be read 1 IDLE IDLE 4 1 IDLE NoIdle No Idle Line is detected 0 Idle Idle Line is detected 1 ORE ORE 3 1 ORE NoOverrun No Overrun error 0 Overrun Overrun error is detected 1 NF NF 2 1 NF NoNoise No noise is detected 0 Noise Noise is detected 1 FE FE 1 1 FE NoError No Framing error is detected 0 Error Framing error or break character is detected 1 PE PE 0 1 PE NoError No parity error 0 Error Parity error 1 ICR ICR Interrupt flag clear register 0x20 0x20 write-only 0x00000000 WUCF Wakeup from Stop mode clear flag 20 1 oneToClear WUCF Clear Clears the WUF flag in the ISR register 1 CMCF Character match clear flag 17 1 oneToClear CMCF Clear Clears the CMF flag in the ISR register 1 CTSCF CTS clear flag 9 1 oneToClear CTSCF Clear Clears the CTSIF flag in the ISR register 1 TCCF Transmission complete clear flag 6 1 oneToClear TCCF Clear Clears the TC flag in the ISR register 1 IDLECF Idle line detected clear flag 4 1 oneToClear IDLECF Clear Clears the IDLE flag in the ISR register 1 ORECF Overrun error clear flag 3 1 oneToClear ORECF Clear Clears the ORE flag in the ISR register 1 NCF Noise detected clear flag 2 1 oneToClear NCF Clear Clears the NF flag in the ISR register 1 FECF Framing error clear flag 1 1 oneToClear FECF Clear Clears the FE flag in the ISR register 1 PECF Parity error clear flag 0 1 oneToClear PECF Clear Clears the PE flag in the ISR register 1 RDR RDR Receive data register 0x24 0x20 read-only 0x00000000 RDR Receive data value 0 9 0 511 TDR TDR Transmit data register 0x28 0x20 read-write 0x00000000 TDR Transmit data value 0 9 0 511 SPI1 Serial peripheral interface/Inter-IC sound SPI 0x40013000 0x0 0x400 registers SPI1 SPI1 global interrupt 35 CR1 CR1 control register 1 0x0 0x10 read-write 0x00000000 BIDIMODE Bidirectional data mode enable 15 1 BIDIMODE Unidirectional 2-line unidirectional data mode selected 0 Bidirectional 1-line bidirectional data mode selected 1 BIDIOE Output enable in bidirectional mode 14 1 BIDIOE OutputDisabled Output disabled (receive-only mode) 0 OutputEnabled Output enabled (transmit-only mode) 1 CRCEN Hardware CRC calculation enable 13 1 CRCEN Disabled CRC calculation disabled 0 Enabled CRC calculation enabled 1 CRCNEXT CRC transfer next 12 1 CRCNEXT TxBuffer Next transmit value is from Tx buffer 0 CRC Next transmit value is from Tx CRC register 1 CRCL CRC length 11 1 CRCL EightBit 8-bit CRC length 0 SixteenBit 16-bit CRC length 1 RXONLY Receive only 10 1 RXONLY FullDuplex Full duplex (Transmit and receive) 0 OutputDisabled Output disabled (Receive-only mode) 1 SSM Software slave management 9 1 SSM Disabled Software slave management disabled 0 Enabled Software slave management enabled 1 SSI Internal slave select 8 1 SSI SlaveSelected 0 is forced onto the NSS pin and the I/O value of the NSS pin is ignored 0 SlaveNotSelected 1 is forced onto the NSS pin and the I/O value of the NSS pin is ignored 1 LSBFIRST Frame format 7 1 LSBFIRST MSBFirst Data is transmitted/received with the MSB first 0 LSBFirst Data is transmitted/received with the LSB first 1 SPE SPI enable 6 1 SPE Disabled Peripheral disabled 0 Enabled Peripheral enabled 1 BR Baud rate control 3 3 BR Div2 f_PCLK / 2 0 Div4 f_PCLK / 4 1 Div8 f_PCLK / 8 2 Div16 f_PCLK / 16 3 Div32 f_PCLK / 32 4 Div64 f_PCLK / 64 5 Div128 f_PCLK / 128 6 Div256 f_PCLK / 256 7 MSTR Master selection 2 1 MSTR Slave Slave configuration 0 Master Master configuration 1 CPOL Clock polarity 1 1 CPOL IdleLow CK to 0 when idle 0 IdleHigh CK to 1 when idle 1 CPHA Clock phase 0 1 CPHA FirstEdge The first clock transition is the first data capture edge 0 SecondEdge The second clock transition is the first data capture edge 1 CR2 CR2 control register 2 0x4 0x10 read-write 0x00000000 RXDMAEN Rx buffer DMA enable 0 1 RXDMAEN Disabled Rx buffer DMA disabled 0 Enabled Rx buffer DMA enabled 1 TXDMAEN Tx buffer DMA enable 1 1 TXDMAEN Disabled Tx buffer DMA disabled 0 Enabled Tx buffer DMA enabled 1 SSOE SS output enable 2 1 SSOE Disabled SS output is disabled in master mode 0 Enabled SS output is enabled in master mode 1 NSSP NSS pulse management 3 1 NSSP NoPulse No NSS pulse 0 PulseGenerated NSS pulse generated 1 FRF Frame format 4 1 FRF Motorola SPI Motorola mode 0 TI SPI TI mode 1 ERRIE Error interrupt enable 5 1 ERRIE Masked Error interrupt masked 0 NotMasked Error interrupt not masked 1 RXNEIE RX buffer not empty interrupt enable 6 1 RXNEIE Masked RXE interrupt masked 0 NotMasked RXE interrupt not masked 1 TXEIE Tx buffer empty interrupt enable 7 1 TXEIE Masked TXE interrupt masked 0 NotMasked TXE interrupt not masked 1 DS Data size 8 4 DS FourBit 4-bit 3 FiveBit 5-bit 4 SixBit 6-bit 5 SevenBit 7-bit 6 EightBit 8-bit 7 NineBit 9-bit 8 TenBit 10-bit 9 ElevenBit 11-bit 10 TwelveBit 12-bit 11 ThirteenBit 13-bit 12 FourteenBit 14-bit 13 FifteenBit 15-bit 14 SixteenBit 16-bit 15 FRXTH FIFO reception threshold 12 1 FRXTH Half RXNE event is generated if the FIFO level is greater than or equal to 1/2 (16-bit) 0 Quarter RXNE event is generated if the FIFO level is greater than or equal to 1/4 (8-bit) 1 LDMA_RX Last DMA transfer for reception 13 1 LDMA_RX Even Number of data to transfer for receive is even 0 Odd Number of data to transfer for receive is odd 1 LDMA_TX Last DMA transfer for transmission 14 1 LDMA_TX Even Number of data to transfer for transmit is even 0 Odd Number of data to transfer for transmit is odd 1 SR SR status register 0x8 0x10 0x00000002 RXNE Receive buffer not empty 0 1 read-only RXNE Empty Rx buffer empty 0 NotEmpty Rx buffer not empty 1 TXE Transmit buffer empty 1 1 read-only TXE NotEmpty Tx buffer not empty 0 Empty Tx buffer empty 1 CRCERR CRC error flag 4 1 read-write zeroToClear CRCERRR read Match CRC value received matches the SPIx_RXCRCR value 0 NoMatch CRC value received does not match the SPIx_RXCRCR value 1 CRCERRW write Clear Clear flag 0 MODF Mode fault 5 1 read-only MODFR NoFault No mode fault occurred 0 Fault Mode fault occurred 1 OVR Overrun flag 6 1 read-only OVRR NoOverrun No overrun occurred 0 Overrun Overrun occurred 1 BSY Busy flag 7 1 read-only BSYR NotBusy SPI not busy 0 Busy SPI busy 1 FRE Frame format error 8 1 read-only FRER NoError No frame format error 0 Error A frame format error occurred 1 FRLVL FIFO reception level 9 2 read-only FRLVLR Empty Rx FIFO Empty 0 Quarter Rx 1/4 FIFO 1 Half Rx 1/2 FIFO 2 Full Rx FIFO full 3 FTLVL FIFO transmission level 11 2 read-only FTLVLR Empty Tx FIFO Empty 0 Quarter Tx 1/4 FIFO 1 Half Tx 1/2 FIFO 2 Full Tx FIFO full 3 DR DR data register 0xC 0x10 read-write 0x00000000 DR Data register 0 16 0 65535 DR8 Direct 8-bit access to data register DR 0xC 0x8 read-write DR Data register 0 8 0 255 CRCPR CRCPR CRC polynomial register 0x10 0x10 read-write 0x00000007 CRCPOLY CRC polynomial register 0 16 0 65535 RXCRCR RXCRCR RX CRC register 0x14 0x10 read-only 0x00000000 RxCRC Rx CRC register 0 16 0 65535 TXCRCR TXCRCR TX CRC register 0x18 0x10 read-only 0x00000000 TxCRC Tx CRC register 0 16 0 65535 SPI2 0x40003800 SPI2 SPI2 global interrupt 36 SPI3 0x40003C00 SPI3 SPI3 global Interrupt 51 SDMMC1 Secure digital input/output interface SDIO 0x40012800 0x0 0x400 registers SDMMC1 SDMMC global Interrupt 49 POWER POWER power control register 0x0 0x20 read-write 0x00000000 PWRCTRL PWRCTRL 0 2 PWRCTRL PowerOff Power off 0 PowerOn Power on 3 CLKCR CLKCR SDI clock control register 0x4 0x20 read-write 0x00000000 HWFC_EN HW Flow Control enable 14 1 HWFC_EN Disabled HW Flow Control is disabled 0 Enabled HW Flow Control is enabled 1 NEGEDGE SDIO_CK dephasing selection bit 13 1 NEGEDGE Rising SDIO_CK generated on the rising edge 0 Falling SDIO_CK generated on the falling edge 1 WIDBUS Wide bus mode enable bit 11 2 WIDBUS BusWidth1 1 lane wide bus 0 BusWidth4 4 lane wide bus 1 BusWidth8 8 lane wide bus 2 BYPASS Clock divider bypass enable bit 10 1 BYPASS Disabled SDIOCLK is divided according to the CLKDIV value before driving the SDIO_CK output signal. 0 Enabled SDIOCLK directly drives the SDIO_CK output signal 1 PWRSAV Power saving configuration bit 9 1 PWRSAV Enabled SDIO_CK clock is always enabled 0 Disabled SDIO_CK is only enabled when the bus is active 1 CLKEN Clock enable bit 8 1 CLKEN Disabled Disable clock 0 Enabled Enable clock 1 CLKDIV Clock divide factor 0 8 0 255 ARG ARG argument register 0x8 0x20 read-write 0x00000000 CMDARG Command argument 0 32 0 4294967295 CMD CMD command register 0xC 0x20 read-write 0x00000000 CE_ATACMD CE-ATA command 14 1 CE_ATACMD Disabled CE-ATA command disabled 0 Enabled CE-ATA command enabled 1 nIEN not Interrupt Enable 13 1 nIEN Disabled Interrupts to the CE-ATA not disabled 0 Enabled Interrupt to the CE-ATA are disabled 1 ENCMDcompl Enable CMD completion 12 1 ENCMDcompl Disabled Command complete signal disabled 0 Enabled Command complete signal enabled 1 SDIOSuspend SD I/O suspend command 11 1 SDIOSuspend Disabled Next command is not a SDIO suspend command 0 Enabled Next command send is a SDIO suspend command 1 CPSMEN Command path state machine (CPSM) Enable bit 10 1 CPSMEN Disabled Command path state machine disabled 0 Enabled Command path state machine enabled 1 WAITPEND CPSM Waits for ends of data transfer (CmdPend internal signal) 9 1 WAITPEND Disabled Don't wait for data end 0 Enabled Wait for end of data transfer signal before sending command 1 WAITINT CPSM waits for interrupt request 8 1 WAITINT Disabled Don't wait for interrupt request 0 Enabled Wait for interrupt request 1 WAITRESP Wait for response bits 6 2 WAITRESP NoResponse No response 0 ShortResponse Short response 1 NoResponse2 No reponse 2 LongResponse Long reponse 3 CMDINDEX Command index 0 6 0 63 RESPCMD RESPCMD command response register 0x10 0x20 read-only 0x00000000 RESPCMD Response command index 0 6 0 63 4 0x4 1-4 RESP%s RESP%s SDIO response %s register 0x14 0x20 read-only 0x00000000 CARDSTATUS Status of a card, which is part of the received response 0 32 0 4294967295 DTIMER DTIMER data timer register 0x24 0x20 read-write 0x00000000 DATATIME Data timeout period 0 32 0 4294967295 DLEN DLEN data length register 0x28 0x20 read-write 0x00000000 DATALENGTH Data length value 0 25 0 33554431 DCTRL DCTRL data control register 0x2C 0x20 read-write 0x00000000 SDIOEN SD I/O enable functions 11 1 SDIOEN Disabled SDIO operations disabled 0 Enabled SDIO operations enabled 1 RWMOD Read wait mode 10 1 RWMOD D2 Read wait control stopping using SDIO_D2 0 Ck Read wait control using SDIO_CK 1 RWSTOP Read wait stop 9 1 RWSTOP Disabled Read wait in progress if RWSTART is enabled 0 Enabled Enable for read wait stop if RWSTART is enabled 1 RWSTART Read wait start 8 1 RWSTART Disabled Don't start read wait operation 0 Enabled Read wait operation starts 1 DBLOCKSIZE Data block size 4 4 0 15 DMAEN DMA enable bit 3 1 DMAEN Disabled Dma disabled 0 Enabled Dma enabled 1 DTMODE Data transfer mode selection 1: Stream or SDIO multibyte data transfer 2 1 DTMODE BlockMode Bloack data transfer 0 StreamMode Stream or SDIO multibyte data transfer 1 DTDIR Data transfer direction selection 1 1 DTDIR ControllerToCard From controller to card 0 CardToController From card to controller 1 DTEN DTEN 0 1 DTEN Disabled Disabled 0 Enabled Start transfer 1 DCOUNT DCOUNT data counter register 0x30 0x20 read-only 0x00000000 DATACOUNT Data count value 0 25 0 33554431 STA STA status register 0x34 0x20 read-only 0x00000000 CEATAEND CE-ATA command completion signal received for CMD61 23 1 CEATAEND NotReceived Completion signal not received 0 Received CE-ATA command completion signal received for CMD61 1 SDIOIT SDIO interrupt received 22 1 SDIOIT NotReceived SDIO interrupt not receieved 0 Received SDIO interrupt received 1 RXDAVL Data available in receive FIFO 21 1 RXDAVL NotAvailable Data not available in receive FIFO 0 Available Data available in receive FIFO 1 TXDAVL Data available in transmit FIFO 20 1 TXDAVL NotAvailable Data not available in transmit FIFO 0 Available Data available in transmit FIFO 1 RXFIFOE Receive FIFO empty 19 1 RXFIFOE NotEmpty Receive FIFO not empty 0 Empty Receive FIFO empty 1 TXFIFOE Transmit FIFO empty 18 1 TXFIFOE NotEmpty Transmit FIFO not empty 0 Empty Transmit FIFO empty. When HW Flow Control is enabled, TXFIFOE signals becomes activated when the FIFO contains 2 words. 1 RXFIFOF Receive FIFO full 17 1 RXFIFOF NotFull Transmit FIFO not full 0 Full Receive FIFO full. When HW Flow Control is enabled, RXFIFOF signals becomes activated 2 words before the FIFO is full. 1 TXFIFOF Transmit FIFO full 16 1 TXFIFOF NotFull Transmit FIFO not full 0 Full Transmit FIFO full 1 RXFIFOHF Receive FIFO half full: there are at least 8 words in the FIFO 15 1 RXFIFOHF NotHalfFull Receive FIFO not half full 0 HalfFull Receive FIFO half full. At least 8 words in the FIFO 1 TXFIFOHE Transmit FIFO half empty: at least 8 words can be written into the FIFO 14 1 TXFIFOHE NotHalfEmpty Transmit FIFO not half empty 0 HalfEmpty Transmit FIFO half empty. At least 8 words can be written into the FIFO 1 RXACT Data receive in progress 13 1 RXACT NotInProgress Data receive not in progress 0 InProgress Data receive in progress 1 TXACT Data transmit in progress 12 1 TXACT NotInProgress Data transmit is not in progress 0 InProgress Data transmit in progress 1 CMDACT Command transfer in progress 11 1 CMDACT NotInProgress Command transfer not in progress 0 InProgress Command tranfer in progress 1 DBCKEND Data block sent/received (CRC check passed) 10 1 DBCKEND NotTransferred Data block not sent/received (CRC check failed) 0 Transferred Data block sent/received (CRC check passed) 1 STBITERR Start bit not detected on all data signals in wide bus mode 9 1 STBITERR Detected No start bit detected error 0 NotDetected Start bit not detected error 1 DATAEND Data end (data counter, SDIDCOUNT, is zero) 8 1 DATAEND NotDone Not done 0 Done Data end (DCOUNT, is zero) 1 CMDSENT Command sent (no response required) 7 1 CMDSENT NotSent Command not sent 0 Sent Command sent (no response required) 1 CMDREND Command response received (CRC check passed) 6 1 CMDREND NotDone Command not done 0 Done Command response received (CRC check passed) 1 RXOVERR Received FIFO overrun error 5 1 RXOVERR NoOverrun No FIFO overrun error 0 Overrun Receive FIFO overrun error 1 TXUNDERR Transmit FIFO underrun error 4 1 TXUNDERR NoUnderrun No transmit FIFO underrun error 0 Underrun Transmit FIFO underrun error 1 DTIMEOUT Data timeout 3 1 DTIMEOUT NoTimeout No data timeout 0 Timeout Data timeout 1 CTIMEOUT Command response timeout 2 1 CTIMEOUT NoTimeout No Command timeout 0 Timeout Command timeout 1 DCRCFAIL Data block sent/received (CRC check failed) 1 1 DCRCFAIL NotFailed No Data block sent/received crc check fail 0 Failed Data block sent/received crc failed 1 CCRCFAIL Command response received (CRC check failed) 0 1 CCRCFAIL NotFailed Command response received, crc check passed 0 Failed Command response received, crc check failed 1 ICR ICR interrupt clear register 0x38 0x20 read-write 0x00000000 CCRCFAILC CCRCFAIL flag clear bit 0 1 CCRCFAILCW write Clear Clear flag 1 CEATAENDC CEATAEND flag clear bit 23 1 SDIOITC SDIOIT flag clear bit 22 1 DBCKENDC DBCKEND flag clear bit 10 1 STBITERRC STBITERR flag clear bit 9 1 DATAENDC DATAEND flag clear bit 8 1 CMDSENTC CMDSENT flag clear bit 7 1 CMDRENDC CMDREND flag clear bit 6 1 RXOVERRC RXOVERR flag clear bit 5 1 TXUNDERRC TXUNDERR flag clear bit 4 1 DTIMEOUTC DTIMEOUT flag clear bit 3 1 CTIMEOUTC CTIMEOUT flag clear bit 2 1 DCRCFAILC DCRCFAIL flag clear bit 1 1 MASK MASK mask register 0x3C 0x20 read-write 0x00000000 CCRCFAILIE Command CRC fail interrupt enable 0 1 CCRCFAILIE Disabled Interrupt disabled 0 Enabled Interrupt enabled 1 CEATAENDIE CE-ATA command completion signal received interrupt enable 23 1 SDIOITIE SDIO mode interrupt received interrupt enable 22 1 RXDAVLIE Data available in Rx FIFO interrupt enable 21 1 TXDAVLIE Data available in Tx FIFO interrupt enable 20 1 RXFIFOEIE Rx FIFO empty interrupt enable 19 1 TXFIFOEIE Tx FIFO empty interrupt enable 18 1 RXFIFOFIE Rx FIFO full interrupt enable 17 1 TXFIFOFIE Tx FIFO full interrupt enable 16 1 RXFIFOHFIE Rx FIFO half full interrupt enable 15 1 TXFIFOHEIE Tx FIFO half empty interrupt enable 14 1 RXACTIE Data receive acting interrupt enable 13 1 TXACTIE Data transmit acting interrupt enable 12 1 CMDACTIE Command acting interrupt enable 11 1 DBCKENDIE Data block end interrupt enable 10 1 STBITERRIE Start bit error interrupt enable 9 1 DATAENDIE Data end interrupt enable 8 1 CMDSENTIE Command sent interrupt enable 7 1 CMDRENDIE Command response received interrupt enable 6 1 RXOVERRIE Rx FIFO overrun error interrupt enable 5 1 TXUNDERRIE Tx FIFO underrun error interrupt enable 4 1 DTIMEOUTIE Data timeout interrupt enable 3 1 CTIMEOUTIE Command timeout interrupt enable 2 1 DCRCFAILIE Data CRC fail interrupt enable 1 1 FIFOCNT FIFOCNT FIFO counter register 0x48 0x20 read-only 0x00000000 FIFOCOUNT Remaining number of words to be written to or read from the FIFO 0 24 0 16777215 FIFO FIFO data FIFO register 0x80 0x20 read-write 0x00000000 FIFOData Receive and transmit FIFO data 0 32 0 4294967295 EXTI External interrupt/event controller EXTI 0x40010400 0x0 0x400 registers PVD_PVM PVD through EXTI line detection 1 EXTI0 EXTI Line 0 interrupt 6 EXTI1 EXTI Line 1 interrupt 7 EXTI2 EXTI Line 2 interrupt 8 EXTI3 EXTI Line 3 interrupt 9 EXTI4 EXTI Line 4 interrupt 10 EXTI9_5 EXTI Line5 to Line9 interrupts 23 EXTI15_10 EXTI Lines 10 to 15 interrupts 40 FPU Floating point unit interrupt 81 IMR1 IMR1 Interrupt mask register 0x0 0x20 read-write 0xFF820000 MR0 Interrupt Mask on line 0 0 1 InterruptMask Masked Interrupt request line is masked 0 Unmasked Interrupt request line is unmasked 1 MR1 Interrupt Mask on line 1 1 1 MR2 Interrupt Mask on line 2 2 1 MR3 Interrupt Mask on line 3 3 1 MR4 Interrupt Mask on line 4 4 1 MR5 Interrupt Mask on line 5 5 1 MR6 Interrupt Mask on line 6 6 1 MR7 Interrupt Mask on line 7 7 1 MR8 Interrupt Mask on line 8 8 1 MR9 Interrupt Mask on line 9 9 1 MR10 Interrupt Mask on line 10 10 1 MR11 Interrupt Mask on line 11 11 1 MR12 Interrupt Mask on line 12 12 1 MR13 Interrupt Mask on line 13 13 1 MR14 Interrupt Mask on line 14 14 1 MR15 Interrupt Mask on line 15 15 1 MR16 Interrupt Mask on line 16 16 1 MR17 Interrupt Mask on line 17 17 1 MR18 Interrupt Mask on line 18 18 1 MR19 Interrupt Mask on line 19 19 1 MR20 Interrupt Mask on line 20 20 1 MR21 Interrupt Mask on line 21 21 1 MR22 Interrupt Mask on line 22 22 1 MR23 Interrupt Mask on line 23 23 1 MR24 Interrupt Mask on line 24 24 1 MR25 Interrupt Mask on line 25 25 1 MR26 Interrupt Mask on line 26 26 1 MR27 Interrupt Mask on line 27 27 1 MR28 Interrupt Mask on line 28 28 1 MR29 Interrupt Mask on line 29 29 1 MR30 Interrupt Mask on line 30 30 1 MR31 Interrupt Mask on line 31 31 1 EMR1 EMR1 Event mask register 0x4 0x20 read-write 0x00000000 MR0 Event Mask on line 0 0 1 EventMask Masked Event request line is masked 0 Unmasked Event request line is unmasked 1 MR1 Event Mask on line 1 1 1 MR2 Event Mask on line 2 2 1 MR3 Event Mask on line 3 3 1 MR4 Event Mask on line 4 4 1 MR5 Event Mask on line 5 5 1 MR6 Event Mask on line 6 6 1 MR7 Event Mask on line 7 7 1 MR8 Event Mask on line 8 8 1 MR9 Event Mask on line 9 9 1 MR10 Event Mask on line 10 10 1 MR11 Event Mask on line 11 11 1 MR12 Event Mask on line 12 12 1 MR13 Event Mask on line 13 13 1 MR14 Event Mask on line 14 14 1 MR15 Event Mask on line 15 15 1 MR16 Event Mask on line 16 16 1 MR17 Event Mask on line 17 17 1 MR18 Event Mask on line 18 18 1 MR19 Event Mask on line 19 19 1 MR20 Event Mask on line 20 20 1 MR21 Event Mask on line 21 21 1 MR22 Event Mask on line 22 22 1 MR23 Event Mask on line 23 23 1 MR24 Event Mask on line 24 24 1 MR25 Event Mask on line 25 25 1 MR26 Event Mask on line 26 26 1 MR27 Event Mask on line 27 27 1 MR28 Event Mask on line 28 28 1 MR29 Event Mask on line 29 29 1 MR30 Event Mask on line 30 30 1 MR31 Event Mask on line 31 31 1 RTSR1 RTSR1 Rising Trigger selection register 0x8 0x20 read-write 0x00000000 TR0 Rising trigger event configuration of line 0 0 1 RisingTrigger Disabled Rising edge trigger is disabled 0 Enabled Rising edge trigger is enabled 1 TR1 Rising trigger event configuration of line 1 1 1 TR2 Rising trigger event configuration of line 2 2 1 TR3 Rising trigger event configuration of line 3 3 1 TR4 Rising trigger event configuration of line 4 4 1 TR5 Rising trigger event configuration of line 5 5 1 TR6 Rising trigger event configuration of line 6 6 1 TR7 Rising trigger event configuration of line 7 7 1 TR8 Rising trigger event configuration of line 8 8 1 TR9 Rising trigger event configuration of line 9 9 1 TR10 Rising trigger event configuration of line 10 10 1 TR11 Rising trigger event configuration of line 11 11 1 TR12 Rising trigger event configuration of line 12 12 1 TR13 Rising trigger event configuration of line 13 13 1 TR14 Rising trigger event configuration of line 14 14 1 TR15 Rising trigger event configuration of line 15 15 1 TR16 Rising trigger event configuration of line 16 16 1 TR18 Rising trigger event configuration of line 18 18 1 TR19 Rising trigger event configuration of line 19 19 1 TR20 Rising trigger event configuration of line 20 20 1 TR21 Rising trigger event configuration of line 21 21 1 TR22 Rising trigger event configuration of line 22 22 1 FTSR1 FTSR1 Falling Trigger selection register 0xC 0x20 read-write 0x00000000 TR0 Falling trigger event configuration of line 0 0 1 FallingTrigger Disabled Falling edge trigger is disabled 0 Enabled Falling edge trigger is enabled 1 TR1 Falling trigger event configuration of line 1 1 1 TR2 Falling trigger event configuration of line 2 2 1 TR3 Falling trigger event configuration of line 3 3 1 TR4 Falling trigger event configuration of line 4 4 1 TR5 Falling trigger event configuration of line 5 5 1 TR6 Falling trigger event configuration of line 6 6 1 TR7 Falling trigger event configuration of line 7 7 1 TR8 Falling trigger event configuration of line 8 8 1 TR9 Falling trigger event configuration of line 9 9 1 TR10 Falling trigger event configuration of line 10 10 1 TR11 Falling trigger event configuration of line 11 11 1 TR12 Falling trigger event configuration of line 12 12 1 TR13 Falling trigger event configuration of line 13 13 1 TR14 Falling trigger event configuration of line 14 14 1 TR15 Falling trigger event configuration of line 15 15 1 TR16 Falling trigger event configuration of line 16 16 1 TR18 Falling trigger event configuration of line 18 18 1 TR19 Falling trigger event configuration of line 19 19 1 TR20 Falling trigger event configuration of line 20 20 1 TR21 Falling trigger event configuration of line 21 21 1 TR22 Falling trigger event configuration of line 22 22 1 SWIER1 SWIER1 Software interrupt event register 0x10 0x20 read-write 0x00000000 SWIER0 Software Interrupt on line 0 0 1 SoftwareInterrupt write Pend Generates an interrupt request 1 SWIER1 Software Interrupt on line 1 1 1 SWIER2 Software Interrupt on line 2 2 1 SWIER3 Software Interrupt on line 3 3 1 SWIER4 Software Interrupt on line 4 4 1 SWIER5 Software Interrupt on line 5 5 1 SWIER6 Software Interrupt on line 6 6 1 SWIER7 Software Interrupt on line 7 7 1 SWIER8 Software Interrupt on line 8 8 1 SWIER9 Software Interrupt on line 9 9 1 SWIER10 Software Interrupt on line 10 10 1 SWIER11 Software Interrupt on line 11 11 1 SWIER12 Software Interrupt on line 12 12 1 SWIER13 Software Interrupt on line 13 13 1 SWIER14 Software Interrupt on line 14 14 1 SWIER15 Software Interrupt on line 15 15 1 SWIER16 Software Interrupt on line 16 16 1 SWIER18 Software Interrupt on line 18 18 1 SWIER19 Software Interrupt on line 19 19 1 SWIER20 Software Interrupt on line 20 20 1 SWIER21 Software Interrupt on line 21 21 1 SWIER22 Software Interrupt on line 22 22 1 PR1 PR1 Pending register 0x14 0x20 read-write 0x00000000 PR0 Pending bit 0 0 1 oneToClear PR0R read NotPending No trigger request occurred 0 Pending Selected trigger request occurred 1 PR0W write Clear Clears pending bit 1 PR1 Pending bit 1 1 1 oneToClear read write PR2 Pending bit 2 2 1 oneToClear read write PR3 Pending bit 3 3 1 oneToClear read write PR4 Pending bit 4 4 1 oneToClear read write PR5 Pending bit 5 5 1 oneToClear read write PR6 Pending bit 6 6 1 oneToClear read write PR7 Pending bit 7 7 1 oneToClear read write PR8 Pending bit 8 8 1 oneToClear read write PR9 Pending bit 9 9 1 oneToClear read write PR10 Pending bit 10 10 1 oneToClear read write PR11 Pending bit 11 11 1 oneToClear read write PR12 Pending bit 12 12 1 oneToClear read write PR13 Pending bit 13 13 1 oneToClear read write PR14 Pending bit 14 14 1 oneToClear read write PR15 Pending bit 15 15 1 oneToClear read write PR16 Pending bit 16 16 1 oneToClear read write PR18 Pending bit 18 18 1 oneToClear read write PR19 Pending bit 19 19 1 oneToClear read write PR20 Pending bit 20 20 1 oneToClear read write PR21 Pending bit 21 21 1 oneToClear read write PR22 Pending bit 22 22 1 oneToClear read write IMR2 IMR2 Interrupt mask register 0x20 0x20 read-write 0xFFFFFF87 MR32 Interrupt Mask on external/internal line 32 0 1 InterruptMask Masked Interrupt request line is masked 0 Unmasked Interrupt request line is unmasked 1 MR33 Interrupt Mask on external/internal line 33 1 1 MR34 Interrupt Mask on external/internal line 34 2 1 MR35 Interrupt Mask on external/internal line 35 3 1 MR36 Interrupt Mask on external/internal line 36 4 1 MR37 Interrupt Mask on external/internal line 37 5 1 MR38 Interrupt Mask on external/internal line 38 6 1 MR39 Interrupt Mask on external/internal line 39 7 1 EMR2 EMR2 Event mask register 0x24 0x20 read-write 0x00000000 MR32 Event mask on external/internal line 32 0 1 EventMask Masked Event request line is masked 0 Unmasked Event request line is unmasked 1 MR33 Event mask on external/internal line 33 1 1 MR34 Event mask on external/internal line 34 2 1 MR35 Event mask on external/internal line 35 3 1 MR36 Event mask on external/internal line 36 4 1 MR37 Event mask on external/internal line 37 5 1 MR38 Event mask on external/internal line 38 6 1 MR39 Event mask on external/internal line 39 7 1 RTSR2 RTSR2 Rising Trigger selection register 0x28 0x20 read-write 0x00000000 RT35 Rising trigger event configuration bit of line 35 3 1 RisingTrigger Disabled Rising edge trigger is disabled 0 Enabled Rising edge trigger is enabled 1 RT36 Rising trigger event configuration bit of line 36 4 1 RT37 Rising trigger event configuration bit of line 37 5 1 RT38 Rising trigger event configuration bit of line 38 6 1 FTSR2 FTSR2 Falling Trigger selection register 0x2C 0x20 read-write 0x00000000 FT35 Falling trigger event configuration bit of line 35 3 1 FallingTrigger Disabled Falling edge trigger is disabled 0 Enabled Falling edge trigger is enabled 1 FT36 Falling trigger event configuration bit of line 36 4 1 FT37 Falling trigger event configuration bit of line 37 5 1 FT38 Falling trigger event configuration bit of line 38 6 1 SWIER2 SWIER2 Software interrupt event register 0x30 0x20 read-write 0x00000000 SWI35 Software interrupt on line 35 3 1 SoftwareInterrupt write Pend Generates an interrupt request 1 SWI36 Software interrupt on line 36 4 1 SWI37 Software interrupt on line 37 5 1 SWI38 Software interrupt on line 38 6 1 PR2 PR2 Pending register 0x34 0x20 read-write 0x00000000 PIF35 Pending interrupt flag on line 35 3 1 oneToClear PIF35R read NotPending No trigger request occurred 0 Pending Selected trigger request occurred 1 PIF35W write Clear Clears pending bit 1 PIF36 Pending interrupt flag on line 36 4 1 oneToClear read write PIF37 Pending interrupt flag on line 37 5 1 oneToClear read write PIF38 Pending interrupt flag on line 38 6 1 oneToClear read write VREFBUF Voltage reference buffer VREF 0x40010030 0x0 0x1D0 registers CSR CSR VREF control and status register 0x0 0x20 0x00000002 ENVR Voltage reference buffer enable 0 1 read-write HIZ High impedance mode 1 1 read-write VRS Voltage reference scale 2 1 read-write VRR Voltage reference buffer ready 3 1 read-only CCR CCR calibration control register 0x4 0x20 read-write 0x00000000 TRIM Trimming code 0 6 CAN1 Controller area network CAN 0x40006400 0x0 0x400 registers CAN1_TX CAN1 TX interrupts 19 CAN1_RX0 CAN1 RX0 interrupts 20 CAN1_RX1 CAN1 RX1 interrupts 21 CAN1_SCE CAN1 SCE interrupt 22 MCR MCR master control register 0x0 0x20 read-write 0x00010002 DBF DBF 16 1 RESET RESET 15 1 TTCM TTCM 7 1 ABOM ABOM 6 1 AWUM AWUM 5 1 NART NART 4 1 RFLM RFLM 3 1 TXFP TXFP 2 1 SLEEP SLEEP 1 1 INRQ INRQ 0 1 MSR MSR master status register 0x4 0x20 0x00000C02 RX RX 11 1 read-only SAMP SAMP 10 1 read-only RXM RXM 9 1 read-only TXM TXM 8 1 read-only SLAKI SLAKI 4 1 read-write WKUI WKUI 3 1 read-write ERRI ERRI 2 1 read-write SLAK SLAK 1 1 read-only INAK INAK 0 1 read-only TSR TSR transmit status register 0x8 0x20 0x1C000000 3 0x1 0-2 LOW%s Lowest priority flag for mailbox %s 29 1 read-only 3 0x1 0-2 TME%s Lowest priority flag for mailbox %s 26 1 read-only CODE CODE 24 2 read-only 3 0x8 0-2 ABRQ%s ABRQ%s 7 1 read-write 3 0x8 0-2 TERR%s TERR%s 3 1 read-write 3 0x8 0-2 ALST%s ALST%s 2 1 read-write 3 0x8 0-2 TXOK%s TXOK%s 1 1 read-write 3 0x8 0-2 RQCP%s RQCP%s 0 1 read-write 2 0x4 0-1 RF%sR RF%sR receive FIFO %s register 0xC 0x20 0x00000000 RFOM RFOM0 5 1 read-write RFOM0W write Release Set by software to release the output mailbox of the FIFO 1 FOVR FOVR0 4 1 read-write FOVR0R read NoOverrun No FIFO x overrun 0 Overrun FIFO x overrun 1 FOVR0W write Clear Clear flag 1 FULL FULL0 3 1 read-write FULL0R read NotFull FIFO x is not full 0 Full FIFO x is full 1 FULL0W write Clear Clear flag 1 FMP FMP0 0 2 read-only IER IER interrupt enable register 0x14 0x20 read-write 0x00000000 SLKIE SLKIE 17 1 SLKIE Disabled No interrupt when SLAKI bit is set 0 Enabled Interrupt generated when SLAKI bit is set 1 WKUIE WKUIE 16 1 WKUIE Disabled No interrupt when WKUI is set 0 Enabled Interrupt generated when WKUI bit is set 1 ERRIE ERRIE 15 1 ERRIE Disabled No interrupt will be generated when an error condition is pending in the CAN_ESR 0 Enabled An interrupt will be generation when an error condition is pending in the CAN_ESR 1 LECIE LECIE 11 1 LECIE Disabled ERRI bit will not be set when the error code in LEC[2:0] is set by hardware on error detection 0 Enabled ERRI bit will be set when the error code in LEC[2:0] is set by hardware on error detection 1 BOFIE BOFIE 10 1 BOFIE Disabled ERRI bit will not be set when BOFF is set 0 Enabled ERRI bit will be set when BOFF is set 1 EPVIE EPVIE 9 1 EPVIE Disabled ERRI bit will not be set when EPVF is set 0 Enabled ERRI bit will be set when EPVF is set 1 EWGIE EWGIE 8 1 EWGIE Disabled ERRI bit will not be set when EWGF is set 0 Enabled ERRI bit will be set when EWGF is set 1 FOVIE1 FOVIE1 6 1 FOVIE1 Disabled No interrupt when FOVR is set 0 Enabled Interrupt generation when FOVR is set 1 FFIE1 FFIE1 5 1 FFIE1 Disabled No interrupt when FULL bit is set 0 Enabled Interrupt generated when FULL bit is set 1 FMPIE1 FMPIE1 4 1 FMPIE1 Disabled No interrupt generated when state of FMP[1:0] bits are not 00b 0 Enabled Interrupt generated when state of FMP[1:0] bits are not 00b 1 FOVIE0 FOVIE0 3 1 FOVIE0 Disabled No interrupt when FOVR bit is set 0 Enabled Interrupt generated when FOVR bit is set 1 FFIE0 FFIE0 2 1 FFIE0 Disabled No interrupt when FULL bit is set 0 Enabled Interrupt generated when FULL bit is set 1 FMPIE0 FMPIE0 1 1 FMPIE0 Disabled No interrupt generated when state of FMP[1:0] bits are not 00 0 Enabled Interrupt generated when state of FMP[1:0] bits are not 00b 1 TMEIE TMEIE 0 1 TMEIE Disabled No interrupt when RQCPx bit is set 0 Enabled Interrupt generated when RQCPx bit is set 1 ESR ESR interrupt enable register 0x18 0x20 0x00000000 REC REC 24 8 read-only TEC TEC 16 8 read-only LEC LEC 4 3 read-write LEC NoError No Error 0 Stuff Stuff Error 1 Form Form Error 2 Ack Acknowledgment Error 3 BitRecessive Bit recessive Error 4 BitDominant Bit dominant Error 5 Crc CRC Error 6 Custom Set by software 7 BOFF BOFF 2 1 read-only EPVF EPVF 1 1 read-only EWGF EWGF 0 1 read-only BTR BTR bit timing register 0x1C 0x20 read-write 0x00000000 SILM SILM 31 1 SILM Normal Normal operation 0 Silent Silent Mode 1 LBKM LBKM 30 1 LBKM Disabled Loop Back Mode disabled 0 Enabled Loop Back Mode enabled 1 SJW SJW 24 2 TS2 TS2 20 3 TS1 TS1 16 4 BRP BRP 0 10 3 0x10 0-2 TX%s CAN Transmit cluster 0x180 TIR TI0R TX mailbox identifier register 0x0 0x20 read-write 0x00000000 STID STID 21 11 EXID EXID 3 18 IDE IDE 2 1 IDE Standard Standard identifier 0 Extended Extended identifier 1 RTR RTR 1 1 RTR Data Data frame 0 Remote Remote frame 1 TXRQ TXRQ 0 1 TDTR TDT0R mailbox data length control and time stamp register 0x4 0x20 read-write 0x00000000 TIME TIME 16 16 TGT TGT 8 1 DLC DLC 0 4 0 8 TDLR TDL0R mailbox data low register 0x8 0x20 read-write 0x00000000 4 0x8 0-3 DATA%s DATA%s 0 8 TDHR TDH0R mailbox data high register 0xC 0x20 read-write 0x00000000 4 0x8 4-7 DATA%s DATA%s 0 8 2 0x10 0-1 RX%s CAN Receive cluster 0x1B0 RIR RI0R receive FIFO mailbox identifier register 0x0 0x20 read-only 0x00000000 STID STID 21 11 EXID EXID 3 18 IDE IDE 2 1 IDE Standard Standard identifier 0 Extended Extended identifier 1 RTR RTR 1 1 RTR Data Data frame 0 Remote Remote frame 1 RDTR RDT0R mailbox data high register 0x4 0x20 read-only 0x00000000 TIME TIME 16 16 FMI FMI 8 8 DLC DLC 0 4 0 8 RDLR RDL0R mailbox data high register 0x8 0x20 read-only 0x00000000 4 0x8 0-3 DATA%s DATA%s 0 8 RDHR RDH0R receive FIFO mailbox data high register 0xC 0x20 read-only 0x00000000 4 0x8 4-7 DATA%s DATA%s 0 8 FMR FMR filter master register 0x200 0x20 read-write 0x2A1C0E01 FINIT Filter initialization mode 0 1 CANSB CAN start bank 8 6 FM1R FM1R filter mode register 0x204 0x20 read-write 0x00000000 28 0x1 0-27 FBM%s Filter mode 0 1 FS1R FS1R filter scale register 0x20C 0x20 read-write 0x00000000 28 0x1 0-27 FSC%s Filter scale configuration 0 1 FFA1R FFA1R filter FIFO assignment register 0x214 0x20 read-write 0x00000000 28 0x1 0-27 FFA%s Filter FIFO assignment for filter %s 0 1 FA1R FA1R filter activation register 0x21C 0x20 read-write 0x00000000 28 0x1 0-27 FACT%s Filter active 0 1 28 0x8 0-27 FB%s CAN Filter Bank cluster 0x240 FR1 F0R1 Filter bank x register 1 0x0 0x20 read-write 0x00000000 FB Filter bits 0 32 FR2 F0R2 Filter bank x register 2 0x4 0x20 read-write 0x00000000 FB Filter bits 0 32 CAN2 0x40006800 CAN2_TX CAN2 TX interrupt 86 CAN2_RX0 CAN2 RX0 interrupt 87 CAN2_RX1 CAN2 RX1 interrupt 88 CAN2_SCE CAN SCE interrupt 89 RTC Real-time clock RTC 0x40002800 0x0 0x400 registers TAMP_STAMP Tamper and TimeStamp interrupts 2 RTC_WKUP RTC Tamper or TimeStamp /CSS on LSE through EXTI line 19 interrupts 3 RTC_ALARM RTC alarms through EXTI line 18 interrupts 41 TR TR time register 0x0 0x20 read-write 0x00000000 PM AM/PM notation 22 1 PM AM AM or 24-hour format 0 PM PM 1 HT Hour tens in BCD format 20 2 0 3 HU Hour units in BCD format 16 4 0 15 MNT Minute tens in BCD format 12 3 0 7 MNU Minute units in BCD format 8 4 0 15 ST Second tens in BCD format 4 3 0 7 SU Second units in BCD format 0 4 0 15 DR DR date register 0x4 0x20 read-write 0x00002101 YT Year tens in BCD format 20 4 0 15 YU Year units in BCD format 16 4 0 15 WDU Week day units 13 3 1 7 MT Month tens in BCD format 12 1 MT Zero Month tens is 0 0 One Month tens is 1 1 MU Month units in BCD format 8 4 0 15 DT Date tens in BCD format 4 2 0 3 DU Date units in BCD format 0 4 0 15 CR CR control register 0x8 0x20 read-write 0x00000000 WUCKSEL Wakeup clock selection 0 3 WUCKSEL Div16 RTC/16 clock is selected 0 Div8 RTC/8 clock is selected 1 Div4 RTC/4 clock is selected 2 Div2 RTC/2 clock is selected 3 ClockSpare ck_spre (usually 1 Hz) clock is selected 4 ClockSpareWithOffset ck_spre (usually 1 Hz) clock is selected and 2^16 is added to the WUT counter value 6 TSEDGE Time-stamp event active edge 3 1 TSEDGE RisingEdge RTC_TS input rising edge generates a time-stamp event 0 FallingEdge RTC_TS input falling edge generates a time-stamp event 1 REFCKON Reference clock detection enable (50 or 60 Hz) 4 1 REFCKON Disabled RTC_REFIN detection disabled 0 Enabled RTC_REFIN detection enabled 1 BYPSHAD Bypass the shadow registers 5 1 BYPSHAD ShadowReg Calendar values (when reading from RTC_SSR, RTC_TR, and RTC_DR) are taken from the shadow registers, which are updated once every two RTCCLK cycles 0 BypassShadowReg Calendar values (when reading from RTC_SSR, RTC_TR, and RTC_DR) are taken directly from the calendar counters 1 FMT Hour format 6 1 FMT Twenty_Four_Hour 24 hour/day format 0 AM_PM AM/PM hour format 1 2 0x1 A,B ALR%sE Alarm %s enable 8 1 ALRAE Disabled Alarm disabled 0 Enabled Alarm enabled 1 WUTE Wakeup timer enable 10 1 WUTE Disabled Wakeup timer disabled 0 Enabled Wakeup timer enabled 1 TSE Time stamp enable 11 1 TSE Disabled Timestamp disabled 0 Enabled Timestamp enabled 1 2 0x1 A,B ALR%sIE Alarm %s interrupt enable 12 1 ALRAIE Disabled Alarm Interrupt disabled 0 Enabled Alarm Interrupt enabled 1 WUTIE Wakeup timer interrupt enable 14 1 WUTIE Disabled Wakeup timer interrupt disabled 0 Enabled Wakeup timer interrupt enabled 1 TSIE Time-stamp interrupt enable 15 1 TSIE Disabled Time-stamp Interrupt disabled 0 Enabled Time-stamp Interrupt enabled 1 ADD1H Add 1 hour (summer time change) 16 1 ADD1HW write Add1 Adds 1 hour to the current time. This can be used for summer time change outside initialization mode 1 SUB1H Subtract 1 hour (winter time change) 17 1 SUB1HW write Sub1 Subtracts 1 hour to the current time. This can be used for winter time change outside initialization mode 1 BKP Backup 18 1 BKP DST_Not_Changed Daylight Saving Time change has not been performed 0 DST_Changed Daylight Saving Time change has been performed 1 COSEL Calibration output selection 19 1 COSEL CalFreq_512Hz Calibration output is 512 Hz (with default prescaler setting) 0 CalFreq_1Hz Calibration output is 1 Hz (with default prescaler setting) 1 POL Output polarity 20 1 POL High The pin is high when ALRAF/ALRBF/WUTF is asserted (depending on OSEL[1:0]) 0 Low The pin is low when ALRAF/ALRBF/WUTF is asserted (depending on OSEL[1:0]) 1 OSEL Output selection 21 2 OSEL Disabled Output disabled 0 AlarmA Alarm A output enabled 1 AlarmB Alarm B output enabled 2 Wakeup Wakeup output enabled 3 COE Calibration output enable 23 1 COE Disabled Calibration output disabled 0 Enabled Calibration output enabled 1 ITSE timestamp on internal event enable 24 1 ISR ISR initialization and status register 0xC 0x20 0x00000007 2 0x1 A,B ALR%sWF Alarm %s write flag 0 1 read-only ALRAWFR UpdateNotAllowed Alarm update not allowed 0 UpdateAllowed Alarm update allowed 1 WUTWF Wakeup timer write flag 2 1 read-only WUTWFR UpdateNotAllowed Wakeup timer configuration update not allowed 0 UpdateAllowed Wakeup timer configuration update allowed 1 SHPF Shift operation pending 3 1 read-write SHPFR read NoShiftPending No shift operation is pending 0 ShiftPending A shift operation is pending 1 INITS Initialization status flag 4 1 read-only INITSR NotInitalized Calendar has not been initialized 0 Initalized Calendar has been initialized 1 RSF Registers synchronization flag 5 1 read-write zeroToClear RSFR read NotSynced Calendar shadow registers not yet synchronized 0 Synced Calendar shadow registers synchronized 1 RSFW write Clear This flag is cleared by software by writing 0 0 INITF Initialization flag 6 1 read-only INITFR NotAllowed Calendar registers update is not allowed 0 Allowed Calendar registers update is allowed 1 INIT Initialization mode 7 1 read-write INIT FreeRunningMode Free running mode 0 InitMode Initialization mode used to program time and date register (RTC_TR and RTC_DR), and prescaler register (RTC_PRER). Counters are stopped and start counting from the new value when INIT is reset. 1 2 0x1 A,B ALR%sF Alarm %s flag 8 1 read-write zeroToClear ALRAFR read Match This flag is set by hardware when the time/date registers (RTC_TR and RTC_DR) match the Alarm register (RTC_ALRMxR) 1 ALRAFW write Clear This flag is cleared by software by writing 0 0 WUTF Wakeup timer flag 10 1 read-write zeroToClear WUTFR read Zero This flag is set by hardware when the wakeup auto-reload counter reaches 0 1 WUTFW write Clear This flag is cleared by software by writing 0 0 TSF Time-stamp flag 11 1 read-write zeroToClear TSFR read TimestampEvent This flag is set by hardware when a time-stamp event occurs 1 TSFW write Clear This flag is cleared by software by writing 0 0 TSOVF Time-stamp overflow flag 12 1 read-write zeroToClear TSOVFR read Overflow This flag is set by hardware when a time-stamp event occurs while TSF is already set 1 TSOVFW write Clear This flag is cleared by software by writing 0 0 TAMP1F Tamper detection flag 13 1 read-write zeroToClear TAMP1FR read Tampered This flag is set by hardware when a tamper detection event is detected on the RTC_TAMPx input 1 TAMP1FW write Clear Flag cleared by software writing 0 0 TAMP2F RTC_TAMP2 detection flag 14 1 read-write zeroToClear read write TAMP3F RTC_TAMP3 detection flag 15 1 read-write zeroToClear read write RECALPF Recalibration pending Flag 16 1 read-only RECALPFR Pending The RECALPF status flag is automatically set to 1 when software writes to the RTC_CALR register, indicating that the RTC_CALR register is blocked. When the new calibration settings are taken into account, this bit returns to 0 1 PRER PRER prescaler register 0x10 0x20 read-write 0x007F00FF PREDIV_A Asynchronous prescaler factor 16 7 0 127 PREDIV_S Synchronous prescaler factor 0 15 0 32767 WUTR WUTR wakeup timer register 0x14 0x20 read-write 0x0000FFFF WUT Wakeup auto-reload value bits 0 16 0 65535 2 0x4 A,B ALRM%sR ALRM%sR Alarm %s register 0x1C 0x20 read-write 0x00000000 MSK1 Alarm seconds mask 7 1 MSK1 Mask Alarm set if the date/day match 0 NotMask Date/day don’t care in Alarm comparison 1 MSK4 Alarm date mask 31 1 WDSEL Week day selection 30 1 WDSEL DateUnits DU[3:0] represents the date units 0 WeekDay DU[3:0] represents the week day. DT[1:0] is don’t care. 1 DT Date tens in BCD format 28 2 0 3 DU Date units or day in BCD format 24 4 0 15 MSK3 Alarm hours mask 23 1 PM AM/PM notation 22 1 PM AM AM or 24-hour format 0 PM PM 1 HT Hour tens in BCD format 20 2 0 3 HU Hour units in BCD format 16 4 0 15 MSK2 Alarm minutes mask 15 1 MNT Minute tens in BCD format 12 3 0 7 MNU Minute units in BCD format 8 4 0 15 ST Second tens in BCD format 4 3 0 7 SU Second units in BCD format 0 4 0 15 WPR WPR write protection register 0x24 0x20 write-only 0x00000000 KEY Write protection key 0 8 0 255 SSR SSR sub second register 0x28 0x20 read-only 0x00000000 SS Sub second value 0 16 0 65535 SHIFTR SHIFTR shift control register 0x2C 0x20 write-only 0x00000000 ADD1S Add one second 31 1 ADD1SW Add1 Add one second to the clock/calendar 1 SUBFS Subtract a fraction of a second 0 15 0 32767 TSTR TSTR time stamp time register 0x30 TSDR TSDR time stamp date register 0x34 TSSSR TSSSR timestamp sub second register 0x38 CALR CALR calibration register 0x3C 0x20 read-write 0x00000000 CALP Increase frequency of RTC by 488.5 ppm 15 1 CALP NoChange No RTCCLK pulses are added 0 IncreaseFreq One RTCCLK pulse is effectively inserted every 2^11 pulses (frequency increased by 488.5 ppm) 1 CALW8 Use an 8-second calibration cycle period 14 1 CALW8 Eight_Second When CALW8 is set to ‘1’, the 8-second calibration cycle period is selected 1 CALW16 Use a 16-second calibration cycle period 13 1 CALW16 Sixteen_Second When CALW16 is set to ‘1’, the 16-second calibration cycle period is selected.This bit must not be set to ‘1’ if CALW8=1 1 CALM Calibration minus 0 9 0 511 TAMPCR TAMPCR tamper configuration register 0x40 0x20 read-write 0x00000000 TAMP1E Tamper 1 detection enable 0 1 TAMP1TRG Active level for tamper 1 1 1 TAMPIE Tamper interrupt enable 2 1 TAMP2E Tamper 2 detection enable 3 1 TAMP2TRG Active level for tamper 2 4 1 TAMP3E Tamper 3 detection enable 5 1 TAMP3TRG Active level for tamper 3 6 1 TAMPTS Activate timestamp on tamper detection event 7 1 TAMPFREQ Tamper sampling frequency 8 3 TAMPFLT Tamper filter count 11 2 TAMPPRCH Tamper precharge duration 13 2 TAMPPUDIS TAMPER pull-up disable 15 1 TAMP1IE Tamper 1 interrupt enable 16 1 TAMP1NOERASE Tamper 1 no erase 17 1 TAMP1MF Tamper 1 mask flag 18 1 TAMP2IE Tamper 2 interrupt enable 19 1 TAMP2NOERASE Tamper 2 no erase 20 1 TAMP2MF Tamper 2 mask flag 21 1 TAMP3IE Tamper 3 interrupt enable 22 1 TAMP3NOERASE Tamper 3 no erase 23 1 TAMP3MF Tamper 3 mask flag 24 1 2 0x4 A,B ALRM%sSSR ALRM%sSSR Alarm %s sub-second register 0x44 0x20 read-write 0x00000000 MASKSS Mask the most-significant bits starting at this bit 24 4 0 15 SS Sub seconds value 0 15 0 32767 OR OR option register 0x4C 0x20 read-write 0x00000000 RTC_ALARM_TYPE RTC_ALARM on PC13 output type 0 1 RTC_OUT_RMP RTC_OUT remap 1 1 32 0x4 0-31 BKP%sR BKP%sR backup register 0x50 0x20 read-write 0x00000000 BKP BKP 0 32 0 4294967295 OTG_FS_GLOBAL USB on the go full speed USB_OTG_FS 0x50000000 0x0 0x400 registers OTG_FS USB OTG FS global Interrupt 67 GOTGCTL GOTGCTL OTG_FS control and status register (OTG_FS_GOTGCTL) 0x0 0x20 0x00000800 SRQSCS Session request success 0 1 read-only SRQ Session request 1 1 read-write HNGSCS Host negotiation success 8 1 read-only HNPRQ HNP request 9 1 read-write HSHNPEN Host set HNP enable 10 1 read-write DHNPEN Device HNP enabled 11 1 read-write CIDSTS Connector ID status 16 1 read-only DBCT Long/short debounce time 17 1 read-only ASVLD A-session valid 18 1 read-only BSVLD B-session valid 19 1 read-only GOTGINT GOTGINT OTG_FS interrupt register (OTG_FS_GOTGINT) 0x4 0x20 read-write 0x00000000 SEDET Session end detected 2 1 SRSSCHG Session request success status change 8 1 HNSSCHG Host negotiation success status change 9 1 HNGDET Host negotiation detected 17 1 ADTOCHG A-device timeout change 18 1 DBCDNE Debounce done 19 1 GAHBCFG GAHBCFG OTG_FS AHB configuration register (OTG_FS_GAHBCFG) 0x8 0x20 read-write 0x00000000 GINT Global interrupt mask 0 1 TXFELVL TxFIFO empty level 7 1 PTXFELVL Periodic TxFIFO empty level 8 1 GUSBCFG GUSBCFG OTG_FS USB configuration register (OTG_FS_GUSBCFG) 0xC 0x20 0x00000A00 TOCAL FS timeout calibration 0 3 read-write PHYSEL Full Speed serial transceiver select 6 1 write-only SRPCAP SRP-capable 8 1 read-write HNPCAP HNP-capable 9 1 read-write TRDT USB turnaround time 10 4 read-write FHMOD Force host mode 29 1 read-write FDMOD Force device mode 30 1 read-write CTXPKT Corrupt Tx packet 31 1 read-write GRSTCTL GRSTCTL OTG_FS reset register (OTG_FS_GRSTCTL) 0x10 0x20 0x20000000 CSRST Core soft reset 0 1 read-write HSRST HCLK soft reset 1 1 read-write FCRST Host frame counter reset 2 1 read-write RXFFLSH RxFIFO flush 4 1 read-write TXFFLSH TxFIFO flush 5 1 read-write TXFNUM TxFIFO number 6 5 read-write AHBIDL AHB master idle 31 1 read-only GINTSTS GINTSTS OTG_FS core interrupt register (OTG_FS_GINTSTS) 0x14 0x20 0x04000020 CMOD Current mode of operation 0 1 read-only MMIS Mode mismatch interrupt 1 1 read-write OTGINT OTG interrupt 2 1 read-only SOF Start of frame 3 1 read-write RXFLVL RxFIFO non-empty 4 1 read-only NPTXFE Non-periodic TxFIFO empty 5 1 read-only GINAKEFF Global IN non-periodic NAK effective 6 1 read-only GOUTNAKEFF Global OUT NAK effective 7 1 read-only ESUSP Early suspend 10 1 read-write USBSUSP USB suspend 11 1 read-write USBRST USB reset 12 1 read-write ENUMDNE Enumeration done 13 1 read-write ISOODRP Isochronous OUT packet dropped interrupt 14 1 read-write EOPF End of periodic frame interrupt 15 1 read-write IEPINT IN endpoint interrupt 18 1 read-only OEPINT OUT endpoint interrupt 19 1 read-only IISOIXFR Incomplete isochronous IN transfer 20 1 read-write IPXFR_INCOMPISOOUT Incomplete periodic transfer(Host mode)/Incomplete isochronous OUT transfer(Device mode) 21 1 read-write HPRTINT Host port interrupt 24 1 read-only HCINT Host channels interrupt 25 1 read-only PTXFE Periodic TxFIFO empty 26 1 read-only CIDSCHG Connector ID status change 28 1 read-write DISCINT Disconnect detected interrupt 29 1 read-write SRQINT Session request/new session detected interrupt 30 1 read-write WKUPINT Resume/remote wakeup detected interrupt 31 1 read-write GINTMSK GINTMSK OTG_FS interrupt mask register (OTG_FS_GINTMSK) 0x18 0x20 0x00000000 MMISM Mode mismatch interrupt mask 1 1 read-write OTGINT OTG interrupt mask 2 1 read-write SOFM Start of frame mask 3 1 read-write RXFLVLM Receive FIFO non-empty mask 4 1 read-write NPTXFEM Non-periodic TxFIFO empty mask 5 1 read-write GINAKEFFM Global non-periodic IN NAK effective mask 6 1 read-write GONAKEFFM Global OUT NAK effective mask 7 1 read-write ESUSPM Early suspend mask 10 1 read-write USBSUSPM USB suspend mask 11 1 read-write USBRST USB reset mask 12 1 read-write ENUMDNEM Enumeration done mask 13 1 read-write ISOODRPM Isochronous OUT packet dropped interrupt mask 14 1 read-write EOPFM End of periodic frame interrupt mask 15 1 read-write EPMISM Endpoint mismatch interrupt mask 17 1 read-write IEPINT IN endpoints interrupt mask 18 1 read-write OEPINT OUT endpoints interrupt mask 19 1 read-write IISOIXFRM Incomplete isochronous IN transfer mask 20 1 read-write IPXFRM_IISOOXFRM Incomplete periodic transfer mask(Host mode)/Incomplete isochronous OUT transfer mask(Device mode) 21 1 read-write PRTIM Host port interrupt mask 24 1 read-write HCIM Host channels interrupt mask 25 1 read-write PTXFEM Periodic TxFIFO empty mask 26 1 read-write CIDSCHGM Connector ID status change mask 28 1 read-write DISCINT Disconnect detected interrupt mask 29 1 read-write SRQIM Session request/new session detected interrupt mask 30 1 read-write WUIM Resume/remote wakeup detected interrupt mask 31 1 read-write GRXSTSR_Device GRXSTSR_Device OTG_FS Receive status debug read(Device mode) 0x1C 0x20 read-only 0x00000000 EPNUM Endpoint number 0 4 BCNT Byte count 4 11 DPID Data PID 15 2 PKTSTS Packet status 17 4 FRMNUM Frame number 21 4 GRXSTSR_Host GRXSTSR_Host OTG status debug read (host mode) GRXSTSR_Device 0x1C 0x20 read-only 0x00000000 CHNUM Channel number 0 4 BCNT Byte count 4 11 DPID Data PID 15 2 PKTSTS Packet status 17 4 GRXSTSP_Device OTG status read and pop (device mode) 0x20 0x20 read-only 0x00000000 FRMNUM Frame number 21 4 PKTSTS Packet status 17 4 DPID Data PID 15 2 BCNT Byte count 4 11 EPNUM Endpoint number 0 4 GRXSTSP_Host OTG status read and pop (host mode) GRXSTSP_Device 0x20 0x20 read-only 0x00000000 PKTSTS Packet status 17 4 DPID Data PID 15 2 BCNT Byte count 4 11 CHNUM Channel number 0 4 GRXFSIZ GRXFSIZ OTG_FS Receive FIFO size register (OTG_FS_GRXFSIZ) 0x24 0x20 read-write 0x00000200 RXFD RxFIFO depth 0 16 DIEPTXF0 DIEPTXF0 OTG_FS non-periodic transmit FIFO size register (Device mode) 0x28 0x20 read-write 0x00000200 TX0FSA Endpoint 0 transmit RAM start address 0 16 TX0FD Endpoint 0 TxFIFO depth 16 16 HNPTXFSIZ HNPTXFSIZ OTG_FS non-periodic transmit FIFO size register (Host mode) DIEPTXF0 0x28 0x20 read-write 0x00000200 NPTXFSA Non-periodic transmit RAM start address 0 16 NPTXFD Non-periodic TxFIFO depth 16 16 GNPTXSTS GNPTXSTS OTG_FS non-periodic transmit FIFO/queue status register (OTG_FS_GNPTXSTS) 0x2C 0x20 read-only 0x00080200 NPTXFSAV Non-periodic TxFIFO space available 0 16 NPTQXSAV Non-periodic transmit request queue space available 16 8 NPTXQTOP Top of the non-periodic transmit request queue 24 7 GCCFG GCCFG OTG_FS general core configuration register (OTG_FS_GCCFG) 0x38 0x20 read-write 0x00000000 PWRDWN Power down 16 1 VBUSASEN Enable the VBUS sensing device 18 1 VBUSBSEN Enable the VBUS sensing device 19 1 SOFOUTEN SOF output enable 20 1 CID CID core ID register 0x3C 0x20 read-write 0x00001000 PRODUCT_ID Product ID field 0 32 HPTXFSIZ HPTXFSIZ OTG_FS Host periodic transmit FIFO size register (OTG_FS_HPTXFSIZ) 0x100 0x20 read-write 0x02000600 PTXSA Host periodic TxFIFO start address 0 16 PTXFSIZ Host periodic TxFIFO depth 16 16 5 0x4 1-5 DIEPTXF%s DIEPTXF%s OTG_FS device IN endpoint transmit FIFO size register 0x104 0x20 read-write 0x02000400 INEPTXSA IN endpoint FIFO2 transmit RAM start address 0 16 INEPTXFD IN endpoint TxFIFO depth 16 16 OTG_FS_HOST USB on the go full speed USB_OTG_FS 0x50000400 0x0 0x400 registers HCFG HCFG OTG_FS host configuration register (OTG_FS_HCFG) 0x0 0x20 0x00000000 FSLSPCS FS/LS PHY clock select 0 2 read-write FSLSS FS- and LS-only support 2 1 read-write HFIR HFIR OTG_FS Host frame interval register 0x4 0x20 read-write 0x0000EA60 FRIVL Frame interval 0 16 HFNUM HFNUM OTG_FS host frame number/frame time remaining register (OTG_FS_HFNUM) 0x8 0x20 read-only 0x00003FFF FRNUM Frame number 0 16 FTREM Frame time remaining 16 16 HPTXSTS HPTXSTS OTG_FS_Host periodic transmit FIFO/queue status register (OTG_FS_HPTXSTS) 0x10 0x20 0x00080100 PTXFSAVL Periodic transmit data FIFO space available 0 16 read-write PTXQSAV Periodic transmit request queue space available 16 8 read-only PTXQTOP Top of the periodic transmit request queue 24 8 read-only HAINT HAINT OTG_FS Host all channels interrupt register 0x14 0x20 read-only 0x00000000 HAINT Channel interrupts 0 16 HAINTMSK HAINTMSK OTG_FS host all channels interrupt mask register 0x18 0x20 read-write 0x00000000 HAINTM Channel interrupt mask 0 16 HPRT HPRT OTG_FS host port control and status register (OTG_FS_HPRT) 0x40 0x20 0x00000000 PCSTS Port connect status 0 1 read-only PCDET Port connect detected 1 1 read-write PENA Port enable 2 1 read-write PENCHNG Port enable/disable change 3 1 read-write POCA Port overcurrent active 4 1 read-only POCCHNG Port overcurrent change 5 1 read-write PRES Port resume 6 1 read-write PSUSP Port suspend 7 1 read-write PRST Port reset 8 1 read-write PLSTS Port line status 10 2 read-only PPWR Port power 12 1 read-write PTCTL Port test control 13 4 read-write PSPD Port speed 17 2 read-only 12 0x20 0-11 HC%s Host channel 0x100 CHAR HCCHAR0 OTG_FS host channel-0 characteristics register (OTG_FS_HCCHAR0) 0x0 0x20 read-write 0x00000000 MPSIZ Maximum packet size 0 11 EPNUM Endpoint number 11 4 EPDIR Endpoint direction 15 1 LSDEV Low-speed device 17 1 EPTYP Endpoint type 18 2 MCNT Multicount 20 2 DAD Device address 22 7 ODDFRM Odd frame 29 1 CHDIS Channel disable 30 1 CHENA Channel enable 31 1 INT HCINT0 OTG_FS host channel-0 interrupt register (OTG_FS_HCINT0) 0x8 0x20 read-write 0x00000000 XFRC Transfer completed 0 1 CHH Channel halted 1 1 STALL STALL response received interrupt 3 1 NAK NAK response received interrupt 4 1 ACK ACK response received/transmitted interrupt 5 1 TXERR Transaction error 7 1 BBERR Babble error 8 1 FRMOR Frame overrun 9 1 DTERR Data toggle error 10 1 INTMSK HCINTMSK0 OTG_FS host channel-0 mask register (OTG_FS_HCINTMSK0) 0xC 0x20 read-write 0x00000000 XFRCM Transfer completed mask 0 1 CHHM Channel halted mask 1 1 STALLM STALL response received interrupt mask 3 1 NAKM NAK response received interrupt mask 4 1 ACKM ACK response received/transmitted interrupt mask 5 1 NYET response received interrupt mask 6 1 TXERRM Transaction error mask 7 1 BBERRM Babble error mask 8 1 FRMORM Frame overrun mask 9 1 DTERRM Data toggle error mask 10 1 TSIZ HCTSIZ0 OTG_FS host channel-0 transfer size register 0x10 0x20 read-write 0x00000000 XFRSIZ Transfer size 0 19 PKTCNT Packet count 19 10 DPID Data PID 29 2 OTG_FS_DEVICE USB on the go full speed USB_OTG_FS 0x50000800 0x0 0x400 registers DCFG DCFG OTG_FS device configuration register (OTG_FS_DCFG) 0x0 0x20 read-write 0x02200000 DSPD Device speed 0 2 NZLSOHSK Non-zero-length status OUT handshake 2 1 DAD Device address 4 7 PFIVL Periodic frame interval 11 2 DCTL DCTL OTG_FS device control register (OTG_FS_DCTL) 0x4 0x20 0x00000000 RWUSIG Remote wakeup signaling 0 1 read-write SDIS Soft disconnect 1 1 read-write GINSTS Global IN NAK status 2 1 read-only GONSTS Global OUT NAK status 3 1 read-only TCTL Test control 4 3 read-write SGINAK Set global IN NAK 7 1 read-write CGINAK Clear global IN NAK 8 1 read-write SGONAK Set global OUT NAK 9 1 read-write CGONAK Clear global OUT NAK 10 1 read-write POPRGDNE Power-on programming done 11 1 read-write DSTS DSTS OTG_FS device status register (OTG_FS_DSTS) 0x8 0x20 read-only 0x00000010 SUSPSTS Suspend status 0 1 ENUMSPD Enumerated speed 1 2 EERR Erratic error 3 1 FNSOF Frame number of the received SOF 8 14 DIEPMSK DIEPMSK OTG_FS device IN endpoint common interrupt mask register (OTG_FS_DIEPMSK) 0x10 0x20 read-write 0x00000000 XFRCM Transfer completed interrupt mask 0 1 EPDM Endpoint disabled interrupt mask 1 1 TOM Timeout condition mask (Non-isochronous endpoints) 3 1 ITTXFEMSK IN token received when TxFIFO empty mask 4 1 INEPNMM IN token received with EP mismatch mask 5 1 INEPNEM IN endpoint NAK effective mask 6 1 DOEPMSK DOEPMSK OTG_FS device OUT endpoint common interrupt mask register (OTG_FS_DOEPMSK) 0x14 0x20 read-write 0x00000000 XFRCM Transfer completed interrupt mask 0 1 EPDM Endpoint disabled interrupt mask 1 1 STUPM SETUP phase done mask 3 1 OTEPDM OUT token received when endpoint disabled mask 4 1 DAINT DAINT OTG_FS device all endpoints interrupt register (OTG_FS_DAINT) 0x18 0x20 read-only 0x00000000 IEPINT IN endpoint interrupt bits 0 16 OEPINT OUT endpoint interrupt bits 16 16 DAINTMSK DAINTMSK OTG_FS all endpoints interrupt mask register (OTG_FS_DAINTMSK) 0x1C 0x20 read-write 0x00000000 IEPM IN EP interrupt mask bits 0 16 OEPM OUT EP interrupt mask bits 16 16 DVBUSDIS DVBUSDIS OTG_FS device VBUS discharge time register 0x28 0x20 read-write 0x000017D7 VBUSDT Device VBUS discharge time 0 16 DVBUSPULSE DVBUSPULSE OTG_FS device VBUS pulsing time register 0x2C 0x20 read-write 0x000005B8 DVBUSP Device VBUS pulsing time 0 12 DIEPEMPMSK DIEPEMPMSK OTG_FS device IN endpoint FIFO empty interrupt mask register 0x34 0x20 read-write 0x00000000 INEPTXFEM IN EP Tx FIFO empty interrupt mask bits 0 16 DIEP0 Device IN endpoint 0 0x100 CTL DIEPCTL0 OTG_FS device control IN endpoint 0 control register (OTG_FS_DIEPCTL0) 0x0 0x20 0x00000000 MPSIZ Maximum packet size 0 2 read-write USBAEP USB active endpoint 15 1 read-only NAKSTS NAK status 17 1 read-only EPTYP Endpoint type 18 2 read-only STALL STALL handshake 21 1 read-write TXFNUM TxFIFO number 22 4 read-write CNAK Clear NAK 26 1 write-only SNAK Set NAK 27 1 write-only EPDIS Endpoint disable 30 1 read-only EPENA Endpoint enable 31 1 read-write INT DIEPINT0 device endpoint-x interrupt register 0x8 0x20 0x00000080 TXFE TXFE 7 1 read-only INEPNE INEPNE 6 1 read-write ITTXFE ITTXFE 4 1 read-write TOC TOC 3 1 read-write EPDISD EPDISD 1 1 read-write XFRC XFRC 0 1 read-write TSIZ DIEPTSIZ0 device endpoint-0 transfer size register 0x10 0x20 read-write 0x00000000 PKTCNT Packet count 19 2 XFRSIZ Transfer size 0 7 TXFSTS DTXFSTS0 OTG_FS device IN endpoint transmit FIFO status register 0x18 0x20 read-only 0x00000000 INEPTFSAV IN endpoint TxFIFO space available 0 16 5 0x20 1-5 DIEP%s Device IN endpoint X 0x120 CTL DIEPCTL1 OTG device endpoint-1 control register 0x0 0x20 0x00000000 EPENA EPENA 31 1 read-write EPDIS EPDIS 30 1 read-write SODDFRM_SD1PID SODDFRM/SD1PID 29 1 write-only SD0PID_SEVNFRM SD0PID/SEVNFRM 28 1 write-only SNAK SNAK 27 1 write-only CNAK CNAK 26 1 write-only TXFNUM TXFNUM 22 4 read-write STALL STALL handshake 21 1 read-write EPTYP EPTYP 18 2 read-write NAKSTS NAKSTS 17 1 read-only EONUM_DPID EONUM/DPID 16 1 read-only USBAEP USBAEP 15 1 read-write MPSIZ MPSIZ 0 11 read-write INT DIEPINT1 device endpoint-1 interrupt register 0x8 TSIZ DIEPTSIZ1 device endpoint-1 transfer size register 0x10 0x20 read-write 0x00000000 MCNT Multi count 29 2 PKTCNT Packet count 19 10 XFRSIZ Transfer size 0 19 TXFSTS DTXFSTS1 OTG_FS device IN endpoint transmit FIFO status register 0x18 DOEP0 Device OUT endpoint 0 0x300 CTL DOEPCTL0 device endpoint-0 control register 0x0 0x20 0x00008000 EPENA EPENA 31 1 read-write EPDIS EPDIS 30 1 read-only SNAK SNAK 27 1 write-only CNAK CNAK 26 1 write-only STALL STALL handshake 21 1 read-write SNPM SNPM 20 1 read-write EPTYP EPTYP 18 2 read-only NAKSTS NAKSTS 17 1 read-only USBAEP USBAEP 15 1 read-only MPSIZ MPSIZ 0 2 read-only INT DOEPINT0 device endpoint-0 interrupt register 0x8 0x20 read-write 0x00000080 B2BSTUP B2BSTUP 6 1 OTEPDIS OTEPDIS 4 1 STUP STUP 3 1 EPDISD EPDISD 1 1 XFRC XFRC 0 1 TSIZ DOEPTSIZ0 device OUT endpoint-0 transfer size register 0x10 0x20 read-write 0x00000000 STUPCNT SETUP packet count 29 2 PKTCNT Packet count 19 1 XFRSIZ Transfer size 0 7 5 0x20 1-5 DOEP%s Device IN endpoint X 0x320 CTL DOEPCTL1 device endpoint-1 control register 0x0 0x20 0x00000000 EPENA EPENA 31 1 read-write EPDIS EPDIS 30 1 read-write SODDFRM SODDFRM 29 1 write-only SD0PID_SEVNFRM SD0PID/SEVNFRM 28 1 write-only SNAK SNAK 27 1 write-only CNAK CNAK 26 1 write-only STALL STALL handshake 21 1 read-write SNPM SNPM 20 1 read-write EPTYP EPTYP 18 2 read-write NAKSTS NAKSTS 17 1 read-only EONUM_DPID EONUM/DPID 16 1 read-only USBAEP USBAEP 15 1 read-write MPSIZ MPSIZ 0 11 read-write INT DOEPINT1 device endpoint-1 interrupt register 0x8 TSIZ DOEPTSIZ1 device OUT endpoint-1 transfer size register 0x10 0x20 read-write 0x00000000 RXDPID_STUPCNT Received data PID/SETUP packet count 29 2 PKTCNT Packet count 19 10 XFRSIZ Transfer size 0 19 OTG_FS_PWRCLK USB on the go full speed USB_OTG_FS 0x50000E00 0x0 0x400 registers PCGCCTL PCGCCTL OTG_FS power and clock gating control register (OTG_FS_PCGCCTL) 0x0 0x20 read-write 0x00000000 STPPCLK Stop PHY clock 0 1 GATEHCLK Gate HCLK 1 1 PHYSUSP PHY Suspended 4 1 SWPMI1 Single Wire Protocol Master Interface SWPMI 0x40008800 0x0 0x400 registers SWPMI1 SWPMI1 global interrupt 76 CR CR SWPMI Configuration/Control register 0x0 0x20 read-write 0x00000000 RXDMA Reception DMA enable 0 1 TXDMA Transmission DMA enable 1 1 RXMODE Reception buffering mode 2 1 TXMODE Transmission buffering mode 3 1 LPBK Loopback mode enable 4 1 SWPACT Single wire protocol master interface activate 5 1 DEACT Single wire protocol master interface deactivate 10 1 BRR BRR SWPMI Bitrate register 0x4 0x20 read-write 0x00000001 BR Bitrate prescaler 0 6 ISR ISR SWPMI Interrupt and Status register 0xC 0x20 read-only 0x000002C2 RXBFF Receive buffer full flag 0 1 TXBEF Transmit buffer empty flag 1 1 RXBERF Receive CRC error flag 2 1 RXOVRF Receive overrun error flag 3 1 TXUNRF Transmit underrun error flag 4 1 RXNE Receive data register not empty 5 1 TXE Transmit data register empty 6 1 TCF Transfer complete flag 7 1 SRF Slave resume flag 8 1 SUSP SUSPEND flag 9 1 DEACTF DEACTIVATED flag 10 1 ICR ICR SWPMI Interrupt Flag Clear register 0x10 0x20 write-only 0x00000000 CRXBFF Clear receive buffer full flag 0 1 CTXBEF Clear transmit buffer empty flag 1 1 CRXBERF Clear receive CRC error flag 2 1 CRXOVRF Clear receive overrun error flag 3 1 CTXUNRF Clear transmit underrun error flag 4 1 CTCF Clear transfer complete flag 7 1 CSRF Clear slave resume flag 8 1 IER IER SWPMI Interrupt Enable register 0x14 0x20 read-write 0x00000000 RXBFIE Receive buffer full interrupt enable 0 1 TXBEIE Transmit buffer empty interrupt enable 1 1 RXBERIE Receive CRC error interrupt enable 2 1 RXOVRIE Receive overrun error interrupt enable 3 1 TXUNRIE Transmit underrun error interrupt enable 4 1 RIE Receive interrupt enable 5 1 TIE Transmit interrupt enable 6 1 TCIE Transmit complete interrupt enable 7 1 SRIE Slave resume interrupt enable 8 1 RFL RFL SWPMI Receive Frame Length register 0x18 0x20 read-only 0x00000000 RFL Receive frame length 0 5 TDR TDR SWPMI Transmit data register 0x1C 0x20 write-only 0x00000000 TD Transmit data 0 32 RDR RDR SWPMI Receive data register 0x20 0x20 read-only 0x00000000 RD received data 0 32 OR OR SWPMI Option register 0x24 0x20 read-write 0x00000000 SWP_TBYP SWP transceiver bypass 0 1 SWP_CLASS SWP class selection 1 1 OPAMP Operational amplifiers OPAMP 0x40007800 0x0 0x400 registers OPAMP1_CSR OPAMP1_CSR OPAMP1 control/status register 0x0 0x20 read-write 0x00000000 OPAEN Operational amplifier Enable 0 1 OPAEN Disabled OpAmp disabled 0 Enabled OpAmp enabled 1 OPALPM Operational amplifier Low Power Mode 1 1 OPALPM NORMAL OpAmp in normal mode 0 LOW OpAmp in low power mode 1 OPAMODE Operational amplifier PGA mode 2 2 OPAMODE PGA_DISABLED internal PGA diabled 0 PGA_ENABLED internal PGA enabled, gain programmed in PGA_GAIN 2 FOLLOWER internal follower 3 PGA_GAIN Operational amplifier Programmable amplifier gain value 4 2 PGA_GAIN Gain2 Gain 2 0 Gain4 Gain 4 1 Gain8 Gain 8 2 Gain16 Gain 16 3 VM_SEL Inverting input selection 8 2 VM_SEL GPIO GPIO connectet to VINM 0 LOW_LEAKAGE Low leakage inputs connected (only available in certein BGA cases 1 PGA_MODE OPAMP in PGA mode 2 VP_SEL Non inverted input selection 10 1 VP_SEL GPIO GPIO connected to VINP 0 DAC DAC connected to VPINP 1 CALON Calibration mode enabled 12 1 CALON Disabled Normal mode 0 Enabled Calibration mode 1 CALSEL Calibration selection 13 1 CALSEL NMOS 0.2V applied to OPAMP inputs during calibration 0 PMOS VDDA-0.2V applied to OPAMP inputs during calibration" 1 USERTRIM allows to switch from AOP offset trimmed values to AOP offset 14 1 USERTRIM Factory Factory trim used 0 User User trim used 1 CALOUT Operational amplifier calibration output 15 1 0 1 OPA_RANGE Operational amplifier power supply range for stability 31 1 OPA_RANGE LOW low range (VDDA < 2.4V 0 HIGH low range (VDDA >2.4V 1 OPAMP1_OTR OPAMP1_OTR OPAMP1 offset trimming register in normal mode 0x4 0x20 read-write 0x00000000 TRIMOFFSETN Trim for NMOS differential pairs 0 5 0 31 TRIMOFFSETP Trim for PMOS differential pairs 8 5 0 31 OPAMP1_LPOTR OPAMP1_LPOTR OPAMP1 offset trimming register in low-power mode 0x8 0x20 read-write 0x00000000 TRIMLPOFFSETN Trim for NMOS differential pairs 0 5 0 31 TRIMLPOFFSETP Trim for PMOS differential pairs 8 5 0 31 OPAMP2_CSR OPAMP2_CSR OPAMP2 control/status register 0x10 0x20 read-write 0x00000000 OPAEN Operational amplifier Enable 0 1 OPALPM Operational amplifier Low Power Mode 1 1 OPAMODE Operational amplifier PGA mode 2 2 PGA_GAIN Operational amplifier Programmable amplifier gain value 4 2 PGA_GAIN Gain2 Gain 2 0 Gain4 Gain 4 1 Gain8 Gain 8 2 Gain16 Gain 16 3 VM_SEL Inverting input selection 8 2 VP_SEL Non inverted input selection 10 1 CALON Calibration mode enabled 12 1 CALSEL Calibration selection 13 1 USERTRIM allows to switch from AOP offset trimmed values to AOP offset 14 1 CALOUT Operational amplifier calibration output 15 1 OPAMP2_OTR OPAMP2_OTR OPAMP2 offset trimming register in normal mode 0x14 0x20 read-write 0x00000000 TRIMOFFSETN Trim for NMOS differential pairs 0 5 0 31 TRIMOFFSETP Trim for PMOS differential pairs 8 5 0 31 OPAMP2_LPOTR OPAMP2_LPOTR OPAMP2 offset trimming register in low-power mode 0x18 0x20 read-write 0x00000000 TRIMLPOFFSETN Trim for NMOS differential pairs 0 5 0 31 TRIMLPOFFSETP Trim for PMOS differential pairs 8 5 0 31 FMC Flexible memory controller FMC 0xA0000000 0x0 0x400 registers FMC FMC global Interrupt 48 BCR1 BCR1 SRAM/NOR-Flash chip-select control register 1 0x0 0x20 read-write 0x000030D0 MBKEN MBKEN 0 1 MBKEN Disabled Corresponding memory bank is disabled 0 Enabled Corresponding memory bank is enabled 1 MUXEN MUXEN 1 1 MUXEN Disabled Address/Data non-multiplexed 0 Enabled Address/Data multiplexed on databus 1 MTYP MTYP 2 2 MTYP SRAM SRAM memory type 0 PSRAM PSRAM (CRAM) memory type 1 Flash NOR Flash/OneNAND Flash 2 MWID MWID 4 2 MWID Bits8 Memory data bus width 8 bits 0 Bits16 Memory data bus width 16 bits 1 Bits32 Memory data bus width 32 bits 2 FACCEN FACCEN 6 1 FACCEN Disabled Corresponding NOR Flash memory access is disabled 0 Enabled Corresponding NOR Flash memory access is enabled 1 BURSTEN BURSTEN 8 1 BURSTEN Disabled Burst mode disabled 0 Enabled Burst mode enabled 1 WAITPOL WAITPOL 9 1 WAITPOL ActiveLow NWAIT active low 0 ActiveHigh NWAIT active high 1 WAITCFG WAITCFG 11 1 WAITCFG BeforeWaitState NWAIT signal is active one data cycle before wait state 0 DuringWaitState NWAIT signal is active during wait state 1 WREN WREN 12 1 WREN Disabled Write operations disabled for the bank by the FMC 0 Enabled Write operations enabled for the bank by the FMC 1 WAITEN WAITEN 13 1 WAITEN Disabled Values inside the FMC_BWTR are taken into account 0 Enabled NWAIT signal enabled 1 EXTMOD EXTMOD 14 1 EXTMOD Disabled Values inside the FMC_BWTR are not taken into account 0 Enabled Values inside the FMC_BWTR are taken into account 1 ASYNCWAIT ASYNCWAIT 15 1 ASYNCWAIT Disabled Wait signal not used in asynchronous mode 0 Enabled Wait signal used even in asynchronous mode 1 CBURSTRW CBURSTRW 19 1 CBURSTRW Disabled Write operations are always performed in asynchronous mode 0 Enabled Write operations are performed in synchronous mode 1 CCLKEN CCLKEN 20 1 CCLKEN Disabled The FMC_CLK is generated continuously during asynchronous and synchronous access. The FMC_CLK clock is activated when the CCLKEN is set 0 Enabled The FMC_CLK is only generated during the synchronous memory access (read/write transaction) 1 WFDIS Write FIFO Disable 21 1 WFDIS Enabled Write FIFO enabled 0 Disabled Write FIFO disabled 1 CPSIZE CRAM page size 16 3 read-write CPSIZE NoBurstSplit No burst split when crossing page boundary 0 Bytes128 128 bytes CRAM page size 1 Bytes256 256 bytes CRAM page size 2 Bytes512 512 bytes CRAM page size 3 Bytes1024 1024 bytes CRAM page size 4 4 0x8 1-4 BTR%s BTR%s SRAM/NOR-Flash chip-select timing register %s 0x4 0x20 read-write 0xFFFFFFFF ACCMOD ACCMOD 28 2 ACCMOD A Access mode A 0 B Access mode B 1 C Access mode C 2 D Access mode D 3 DATLAT DATLAT 24 4 0 15 CLKDIV CLKDIV 20 4 1 15 BUSTURN BUSTURN 16 4 0 15 DATAST DATAST 8 8 1 255 ADDHLD ADDHLD 4 4 1 15 ADDSET ADDSET 0 4 0 15 3 0x8 2-4 BCR%s BCR%s SRAM/NOR-Flash chip-select control register %s 0x8 0x20 read-write 0x000030D0 CBURSTRW CBURSTRW 19 1 ASYNCWAIT ASYNCWAIT 15 1 EXTMOD EXTMOD 14 1 WAITEN WAITEN 13 1 WREN WREN 12 1 WAITCFG WAITCFG 11 1 WAITPOL WAITPOL 9 1 BURSTEN BURSTEN 8 1 FACCEN FACCEN 6 1 MWID MWID 4 2 MTYP MTYP 2 2 MUXEN MUXEN 1 1 MBKEN MBKEN 0 1 CPSIZE CRAM page size 16 3 read-write PCR PCR PC Card/NAND Flash control register 3 0x80 0x20 read-write 0x00000018 ECCPS ECCPS 17 3 ECCPS Bytes256 ECC page size 256 bytes 0 Bytes512 ECC page size 512 bytes 1 Bytes1024 ECC page size 1024 bytes 2 Bytes2048 ECC page size 2048 bytes 3 Bytes4096 ECC page size 4096 bytes 4 Bytes8192 ECC page size 8192 bytes 5 TAR TAR 13 4 0 15 TCLR TCLR 9 4 0 15 ECCEN ECCEN 6 1 ECCEN Disabled ECC logic is disabled and reset 0 Enabled ECC logic is enabled 1 PWID PWID 4 2 PWID Bits8 External memory device width 8 bits 0 Bits16 External memory device width 16 bits 1 PTYP PTYP 3 1 PTYP NANDFlash NAND Flash 1 PBKEN PBKEN 2 1 PBKEN Disabled Corresponding memory bank is disabled 0 Enabled Corresponding memory bank is enabled 1 PWAITEN PWAITEN 1 1 PWAITEN Disabled Wait feature disabled 0 Enabled Wait feature enabled 1 SR SR FIFO status and interrupt register 3 0x84 0x20 0x00000040 FEMPT FEMPT 6 1 read-only FEMPT NotEmpty FIFO not empty 0 Empty FIFO empty 1 IFEN IFEN 5 1 read-write IFEN Disabled Interrupt falling edge detection request disabled 0 Enabled Interrupt falling edge detection request enabled 1 ILEN ILEN 4 1 read-write ILEN Disabled Interrupt high-level detection request disabled 0 Enabled Interrupt high-level detection request enabled 1 IREN IREN 3 1 read-write IREN Disabled Interrupt rising edge detection request disabled 0 Enabled Interrupt rising edge detection request enabled 1 IFS IFS 2 1 read-write IFS DidNotOccur Interrupt falling edge did not occur 0 Occurred Interrupt falling edge occurred 1 ILS ILS 1 1 read-write ILS DidNotOccur Interrupt high-level did not occur 0 Occurred Interrupt high-level occurred 1 IRS IRS 0 1 read-write IRS DidNotOccur Interrupt rising edge did not occur 0 Occurred Interrupt rising edge occurred 1 PMEM PMEM Common memory space timing register 3 0x88 0x20 read-write 0xFCFCFCFC MEMHIZ MEMHIZx 24 8 0 254 MEMHOLD MEMHOLDx 16 8 1 254 MEMWAIT MEMWAITx 8 8 1 254 MEMSET MEMSETx 0 8 0 254 PATT PATT Attribute memory space timing register 3 0x8C 0x20 read-write 0xFCFCFCFC ATTHIZ ATTHIZx 24 8 0 254 ATTHOLD ATTHOLDx 16 8 1 254 ATTWAIT ATTWAITx 8 8 1 254 ATTSET ATTSETx 0 8 0 254 ECCR ECCR ECC result register 3 0x94 0x20 read-only 0x00000000 ECC ECCx 0 32 0 4294967295 4 0x8 1-4 BWTR%s BWTR%s SRAM/NOR-Flash write timing registers %s 0x104 0x20 read-write 0x0FFFFFFF ACCMOD ACCMOD 28 2 ACCMOD A Access mode A 0 B Access mode B 1 C Access mode C 2 D Access mode D 3 DATAST DATAST 8 8 1 255 ADDHLD ADDHLD 4 4 1 15 ADDSET ADDSET 0 4 0 15 BUSTURN Bus turnaround phase duration 16 4 read-write 0 15 CRS Clock recovery system CRS 0x40006000 0x0 0x400 registers CRS CRS global interrupt 82 CR CR control register 0x0 0x20 read-write 0x00002000 TRIM HSI48 oscillator smooth trimming 8 6 0 63 SWSYNC Generate software SYNC event 7 1 SWSYNC Sync A software sync is generated 1 AUTOTRIMEN Automatic trimming enable 6 1 AUTOTRIMEN Disabled Automatic trimming disabled 0 Enabled Automatic trimming enabled 1 CEN Frequency error counter enable 5 1 CEN Disabled Frequency error counter disabled 0 Enabled Frequency error counter enabled 1 SYNCOKIE SYNC event OK interrupt enable 0 1 SYNCOKIE Disabled Interrupt disabled 0 Enabled Interrupt enabled 1 ESYNCIE Expected SYNC interrupt enable 3 1 ERRIE Synchronization or trimming error interrupt enable 2 1 SYNCWARNIE SYNC warning interrupt enable 1 1 CFGR CFGR configuration register 0x4 0x20 read-write 0x2022BB7F SYNCPOL SYNC polarity selection 31 1 SYNCPOL RisingEdge SYNC active on rising edge 0 FallingEdge SYNC active on falling edge 1 SYNCSRC SYNC signal source selection 28 2 SYNCSRC GPIO_AF GPIO AF (crs_sync_in_1) selected as SYNC signal source 0 LSE LSE (crs_sync_in_2) selected as SYNC signal source 1 USB_SOF USB SOF (crs_sync_in_3) selected as SYNC signal source 2 SYNCDIV SYNC divider 24 3 SYNCDIV Div1 SYNC not divided 0 Div2 SYNC divided by 2 1 Div4 SYNC divided by 4 2 Div8 SYNC divided by 8 3 Div16 SYNC divided by 16 4 Div32 SYNC divided by 32 5 Div64 SYNC divided by 64 6 Div128 SYNC divided by 128 7 FELIM Frequency error limit 16 8 0 255 RELOAD Counter reload value 0 16 0 65535 ISR ISR interrupt and status register 0x8 0x20 read-only 0x00000000 FECAP Frequency error capture 16 16 0 65535 FEDIR Frequency error direction 15 1 FEDIR UpCounting Error in up-counting direction 0 DownCounting Error in down-counting direction 1 SYNCOKF SYNC event OK flag 0 1 SYNCOKF NotSignaled Signal not set 0 Signaled Signal set 1 TRIMOVF Trimming overflow or underflow 10 1 SYNCMISS SYNC missed 9 1 SYNCERR SYNC error 8 1 ESYNCF Expected SYNC flag 3 1 ERRF Error flag 2 1 SYNCWARNF SYNC warning flag 1 1 ICR ICR interrupt flag clear register 0xC 0x20 read-write 0x00000000 SYNCOKC SYNC event OK clear flag 0 1 SYNCOKC Clear Clear flag 1 ESYNCC Expected SYNC clear flag 3 1 ERRC Error clear flag 2 1 SYNCWARNC SYNC warning clear flag 1 1 DCMI Digital camera interface DCMI 0x50050000 0x0 0x400 registers DCMI DCMI global interrupt 85 CR CR control register 1 0x0 0x20 read-write 0x00000000 ENABLE DCMI enable 14 1 ENABLE Disabled DCMI disabled 0 Enabled DCMI enabled 1 EDM Extended data mode 10 2 EDM BitWidth8 Interface captures 8-bit data on every pixel clock 0 BitWidth10 Interface captures 10-bit data on every pixel clock 1 BitWidth12 Interface captures 12-bit data on every pixel clock 2 BitWidth14 Interface captures 14-bit data on every pixel clock 3 FCRC Frame capture rate control 8 2 FCRC All All frames are captured 0 Alternate Every alternate frame captured (50% bandwidth reduction) 1 OneOfFour One frame out of four captured (75% bandwidth reduction) 2 VSPOL Vertical synchronization polarity 7 1 VSPOL ActiveLow DCMI_VSYNC active low 0 ActiveHigh DCMI_VSYNC active high 1 HSPOL Horizontal synchronization polarity 6 1 HSPOL ActiveLow DCMI_HSYNC active low 0 ActiveHigh DCMI_HSYNC active high 1 PCKPOL Pixel clock polarity 5 1 PCKPOL FallingEdge Falling edge active 0 RisingEdge Rising edge active 1 ESS Embedded synchronization select 4 1 ESS Hardware Hardware synchronization data capture (frame/line start/stop) is synchronized with the DCMI_HSYNC/DCMI_VSYNC signals 0 Embedded Embedded synchronization data capture is synchronized with synchronization codes embedded in the data flow 1 JPEG JPEG format 3 1 JPEG Uncompressed Uncompressed video format 0 JPEG This bit is used for JPEG data transfers. The DCMI_HSYNC signal is used as data enable. The crop and embedded synchronization features (ESS bit) cannot be used in this mode 1 CROP Crop feature 2 1 CROP Full The full image is captured. In this case the total number of bytes in an image frame must be a multiple of four 0 Cropped Only the data inside the window specified by the crop register is captured. If the size of the crop window exceeds the picture size, then only the picture size is captured 1 CM Capture mode 1 1 CM Continuous Continuous grab mode - The received data are transferred into the destination memory through the DMA. The buffer location and mode (linear or circular buffer) is controlled through the system DMA 0 Snapshot Snapshot mode (single frame) - Once activated, the interface waits for the start of frame and then transfers a single frame through the DMA. At the end of the frame, the CAPTURE bit is automatically reset 1 CAPTURE Capture enable 0 1 CAPTURE Disabled Capture disabled 0 Enabled Capture enabled 1 OELS Odd/Even Line Select (Line Select Start) 20 1 OELS Odd Interface captures first line after the frame start, second one being dropped 0 Even Interface captures second line from the frame start, first one being dropped 1 LSM Line Select mode 19 1 LSM All Interface captures all received lines 0 Half Interface captures one line out of two 1 OEBS Odd/Even Byte Select (Byte Select Start) 18 1 OEBS Odd Interface captures first data (byte or double byte) from the frame/line start, second one being dropped 0 Even Interface captures second data (byte or double byte) from the frame/line start, first one being dropped 1 BSM Byte Select mode 16 2 BSM All Interface captures all received data 0 EveryOther Interface captures every other byte from the received data 1 Fourth Interface captures one byte out of four 2 TwoOfFour Interface captures two bytes out of four 3 SR SR status register 0x4 0x20 read-only 0x00000000 FNE FIFO not empty 2 1 FNE NotEmpty FIFO contains valid data 0 Empty FIFO empty 1 VSYNC VSYNC 1 1 VSYNC ActiveFrame Active frame 0 BetweenFrames Synchronization between frames 1 HSYNC HSYNC 0 1 HSYNC ActiveLine Active line 0 BetweenLines Synchronization between lines 1 RIS RIS raw interrupt status register 0x8 0x20 read-only 0x00000000 LINE_RIS Line raw interrupt status 4 1 LINE_RIS Cleared Interrupt cleared 0 Set Interrupt set 1 VSYNC_RIS VSYNC raw interrupt status 3 1 VSYNC_RIS Cleared Interrupt cleared 0 Set Interrupt set 1 ERR_RIS Synchronization error raw interrupt status 2 1 ERR_RIS NoError No synchronization error detected 0 SynchronizationError Embedded synchronization characters are not received in the correct order 1 OVR_RIS Overrun raw interrupt status 1 1 OVR_RIS NoOverrun No data buffer overrun occurred 0 OverrunOccured A data buffer overrun occurred and the data FIFO is corrupted. The bit is cleared by setting the OVR_ISC bit of the DCMI_ICR register 1 FRAME_RIS Capture complete raw interrupt status 0 1 FRAME_RIS NoNewCapture No new capture 0 FrameCaptured A frame has been captured 1 IER IER interrupt enable register 0xC 0x20 read-write 0x00000000 LINE_IE Line interrupt enable 4 1 LINE_IE Disabled No interrupt generation when the line is received 0 Enabled An Interrupt is generated when a line has been completely received 1 VSYNC_IE VSYNC interrupt enable 3 1 VSYNC_IE Disabled No interrupt generation 0 Enabled An interrupt is generated on each DCMI_VSYNC transition from the inactive to the active state 1 ERR_IE Synchronization error interrupt enable 2 1 ERR_IE Disabled No interrupt generation 0 Enabled An interrupt is generated if the embedded synchronization codes are not received in the correct order 1 OVR_IE Overrun interrupt enable 1 1 OVR_IE Disabled No interrupt generation 0 Enabled An interrupt is generated if the DMA was not able to transfer the last data before new data (32-bit) are received 1 FRAME_IE Capture complete interrupt enable 0 1 FRAME_IE Disabled No interrupt generation 0 Enabled An interrupt is generated at the end of each received frame/crop window (in crop mode) 1 MIS MIS masked interrupt status register 0x10 0x20 read-only 0x00000000 LINE_MIS Line masked interrupt status 4 1 LINE_MIS Disabled No interrupt generation when the line is received 0 Enabled An Interrupt is generated when a line has been completely received and the LINE_IE bit is set in DCMI_IER 1 VSYNC_MIS VSYNC masked interrupt status 3 1 VSYNC_MIS Disabled No interrupt is generated on DCMI_VSYNC transitions 0 Enabled An interrupt is generated on each DCMI_VSYNC transition from the inactive to the active state and the VSYNC_IE bit is set in DCMI_IER 1 ERR_MIS Synchronization error masked interrupt status 2 1 ERR_MIS Disabled No interrupt is generated on a synchronization error 0 Enabled An interrupt is generated if the embedded synchronization codes are not received in the correct order and the ERR_IE bit in DCMI_IER is set 1 OVR_MIS Overrun masked interrupt status 1 1 OVR_MIS Disabled No interrupt is generated on overrun 0 Enabled An interrupt is generated if the DMA was not able to transfer the last data before new data (32-bit) are received and the OVR_IE bit is set in DCMI_IER 1 FRAME_MIS Capture complete masked interrupt status 0 1 FRAME_MIS Disabled No interrupt is generated after a complete capture 0 Enabled An interrupt is generated at the end of each received frame/crop window (in crop mode) and the FRAME_IE bit is set in DCMI_IER 1 ICR ICR interrupt clear register 0x14 0x20 write-only 0x00000000 LINE_ISC line interrupt status clear 4 1 LINE_ISC Clear Setting this bit clears the LINE_RIS flag in the DCMI_RIS register 1 VSYNC_ISC Vertical synch interrupt status clear 3 1 VSYNC_ISC Clear Setting this bit clears the VSYNC_RIS flag in the DCMI_RIS register 1 ERR_ISC Synchronization error interrupt status clear 2 1 ERR_ISC Clear Setting this bit clears the ERR_RIS flag in the DCMI_RIS register 1 OVR_ISC Overrun interrupt status clear 1 1 OVR_ISC Clear Setting this bit clears the OVR_RIS flag in the DCMI_RIS register 1 FRAME_ISC Capture complete interrupt status clear 0 1 FRAME_ISC Clear Setting this bit clears the FRAME_RIS flag in the DCMI_RIS register 1 ESCR ESCR embedded synchronization code register 0x18 0x20 read-write 0x00000000 FEC Frame end delimiter code 24 8 LEC Line end delimiter code 16 8 LSC Line start delimiter code 8 8 FSC Frame start delimiter code 0 8 ESUR ESUR embedded synchronization unmask register 0x1C 0x20 read-write 0x00000000 FEU Frame end delimiter unmask 24 8 LEU Line end delimiter unmask 16 8 LSU Line start delimiter unmask 8 8 FSU Frame start delimiter unmask 0 8 CWSTRT CWSTRT crop window start 0x20 0x20 read-write 0x00000000 VST Vertical start line count 16 13 0 8191 HOFFCNT Horizontal offset count 0 14 0 16383 CWSIZE CWSIZE crop window size 0x24 0x20 read-write 0x00000000 VLINE Vertical line count 16 14 0 16383 CAPCNT Capture count 0 14 0 16383 DR DR data register 0x28 0x20 read-only 0x00000000 4 0x8 0-3 BYTE%s Data byte %s 0 8 0 255 HASH Hash processor HASH 0x50060400 0x0 0x400 registers CR CR control register 0x0 0x20 0x00000000 INIT Initialize message digest calculation 2 1 write-only DMAE DMA enable 3 1 read-write DATATYPE Data type selection 4 2 read-write MODE Mode selection 6 1 read-write ALGO0 Algorithm selection 7 1 read-write NBW Number of words already pushed 8 4 read-only DINNE DIN not empty 12 1 read-only MDMAT Multiple DMA Transfers 13 1 read-write LKEY Long key selection 16 1 read-write ALGO1 ALGO 18 1 read-write DIN DIN data input register 0x4 0x20 read-write 0x00000000 DATAIN Data input 0 32 STR STR start register 0x8 0x20 0x00000000 DCAL Digest calculation 8 1 write-only NBLW Number of valid bits in the last word of the message 0 5 read-write 1 0x4 0-0 HR%s HR%s digest registers 0xC 0x20 read-only 0x00000000 H H0 0 32 IMR IMR interrupt enable register 0x20 0x20 read-write 0x00000000 DCIE Digest calculation completion interrupt enable 1 1 DINIE Data input interrupt enable 0 1 SR SR status register 0x24 0x20 0x00000001 BUSY Busy bit 3 1 read-only DMAS DMA Status 2 1 read-only DCIS Digest calculation completion interrupt status 1 1 read-write DINIS Data input interrupt status 0 1 read-write 54 0x4 0-53 CSR%s CSR%s context swap registers 0xF8 0x20 read-write 0x00000000 CSR CSR0 0 32 8 0x4 0-7 HASH_HR%s HASH_HR%s HASH digest register %s 0x310 0x20 read-only 0x00000000 H H0 0 32 DMA2D DMA2D controller DMA2D 0x4002B000 0x0 0xC00 registers DMA2D DMA2D global interrupt 90 CR CR control register 0x0 0x20 read-write 0x00000000 MODE DMA2D mode 16 2 MODE MemoryToMemory Memory-to-memory (FG fetch only) 0 MemoryToMemoryPFC Memory-to-memory with PFC (FG fetch only with FG PFC active) 1 MemoryToMemoryPFCBlending Memory-to-memory with blending (FG and BG fetch with PFC and blending) 2 RegisterToMemory Register-to-memory 3 CEIE Configuration Error Interrupt Enable 13 1 CEIE Disabled CE interrupt disabled 0 Enabled CE interrupt enabled 1 CTCIE CLUT transfer complete interrupt enable 12 1 CTCIE Disabled CTC interrupt disabled 0 Enabled CTC interrupt enabled 1 CAEIE CLUT access error interrupt enable 11 1 CAEIE Disabled CAE interrupt disabled 0 Enabled CAE interrupt enabled 1 TWIE Transfer watermark interrupt enable 10 1 TWIE Disabled TW interrupt disabled 0 Enabled TW interrupt enabled 1 TCIE Transfer complete interrupt enable 9 1 TCIE Disabled TC interrupt disabled 0 Enabled TC interrupt enabled 1 TEIE Transfer error interrupt enable 8 1 TEIE Disabled TE interrupt disabled 0 Enabled TE interrupt enabled 1 ABORT Abort 2 1 ABORT AbortRequest Transfer abort requested 1 SUSP Suspend 1 1 SUSP NotSuspended Transfer not suspended 0 Suspended Transfer suspended 1 START Start 0 1 START Start Launch the DMA2D 1 ISR ISR Interrupt Status Register 0x4 0x20 read-only 0x00000000 CEIF Configuration error interrupt flag 5 1 CTCIF CLUT transfer complete interrupt flag 4 1 CAEIF CLUT access error interrupt flag 3 1 TWIF Transfer watermark interrupt flag 2 1 TCIF Transfer complete interrupt flag 1 1 TEIF Transfer error interrupt flag 0 1 IFCR IFCR interrupt flag clear register 0x8 0x20 read-write 0x00000000 CCEIF Clear configuration error interrupt flag 5 1 CCEIF Clear Clear the CEIF flag in the ISR register 1 CCTCIF Clear CLUT transfer complete interrupt flag 4 1 CCTCIF Clear Clear the CTCIF flag in the ISR register 1 CAECIF Clear CLUT access error interrupt flag 3 1 CAECIF Clear Clear the CAEIF flag in the ISR register 1 CTWIF Clear transfer watermark interrupt flag 2 1 CTWIF Clear Clear the TWIF flag in the ISR register 1 CTCIF Clear transfer complete interrupt flag 1 1 CTCIF Clear Clear the TCIF flag in the ISR register 1 CTEIF Clear Transfer error interrupt flag 0 1 CTEIF Clear Clear the TEIF flag in the ISR register 1 FGMAR FGMAR foreground memory address register 0xC 0x20 read-write 0x00000000 MA Memory address 0 32 FGOR FGOR foreground offset register 0x10 0x20 read-write 0x00000000 LO Line offset 0 14 0 16383 BGMAR BGMAR background memory address register 0x14 0x20 read-write 0x00000000 MA Memory address 0 32 BGOR BGOR background offset register 0x18 0x20 read-write 0x00000000 LO Line offset 0 14 0 16383 FGPFCCR FGPFCCR foreground PFC control register 0x1C 0x20 read-write 0x00000000 ALPHA Alpha value 24 8 0 255 AM Alpha mode 16 2 AM NoModify No modification of alpha channel 0 Replace Replace with value in ALPHA[7:0] 1 Multiply Multiply with value in ALPHA[7:0] 2 CS CLUT size 8 8 0 255 START Start 5 1 START Start Start the automatic loading of the CLUT 1 CCM CLUT color mode 4 1 CCM ARGB8888 CLUT color format ARGB8888 0 RGB888 CLUT color format RGB888 1 CM Color mode 0 4 CM ARGB8888 Color mode ARGB8888 0 RGB888 Color mode RGB888 1 RGB565 Color mode RGB565 2 ARGB1555 Color mode ARGB1555 3 ARGB4444 Color mode ARGB4444 4 L8 Color mode L8 5 AL44 Color mode AL44 6 AL88 Color mode AL88 7 L4 Color mode L4 8 A8 Color mode A8 9 A4 Color mode A4 10 RBS Red Blue Swap 21 1 AI Alpha Inverted 20 1 FGCOLR FGCOLR foreground color register 0x20 0x20 read-write 0x00000000 RED Red Value 16 8 0 255 GREEN Green Value 8 8 0 255 BLUE Blue Value 0 8 0 255 BGPFCCR BGPFCCR background PFC control register 0x24 0x20 read-write 0x00000000 ALPHA Alpha value 24 8 0 255 AM Alpha mode 16 2 AM NoModify No modification of alpha channel 0 Replace Replace with value in ALPHA[7:0] 1 Multiply Multiply with value in ALPHA[7:0] 2 CS CLUT size 8 8 0 255 START Start 5 1 START Start Start the automatic loading of the CLUT 1 CCM CLUT Color mode 4 1 CCM ARGB8888 CLUT color format ARGB8888 0 RGB888 CLUT color format RGB888 1 CM Color mode 0 4 CM ARGB8888 Color mode ARGB8888 0 RGB888 Color mode RGB888 1 RGB565 Color mode RGB565 2 ARGB1555 Color mode ARGB1555 3 ARGB4444 Color mode ARGB4444 4 L8 Color mode L8 5 AL44 Color mode AL44 6 AL88 Color mode AL88 7 L4 Color mode L4 8 A8 Color mode A8 9 A4 Color mode A4 10 RBS Red Blue Swap 21 1 AI Alpha Inverted 20 1 BGCOLR BGCOLR background color register 0x28 0x20 read-write 0x00000000 RED Red Value 16 8 0 255 GREEN Green Value 8 8 0 255 BLUE Blue Value 0 8 0 255 FGCMAR FGCMAR foreground CLUT memory address register 0x2C 0x20 read-write 0x00000000 MA Memory Address 0 32 BGCMAR BGCMAR background CLUT memory address register 0x30 0x20 read-write 0x00000000 MA Memory address 0 32 OPFCCR OPFCCR output PFC control register 0x34 0x20 read-write 0x00000000 CM Color mode 0 3 CM ARGB8888 ARGB8888 0 RGB888 RGB888 1 RGB565 RGB565 2 ARGB1555 ARGB1555 3 ARGB4444 ARGB4444 4 RBS Red Blue Swap 21 1 AI Alpha Inverted 20 1 OCOLR OCOLR output color register 0x38 0x20 read-write 0x00000000 APLHA Alpha Channel Value 24 8 RED Red Value 16 8 GREEN Green Value 8 8 BLUE Blue Value 0 8 OMAR OMAR output memory address register 0x3C 0x20 read-write 0x00000000 MA Memory Address 0 32 OOR OOR output offset register 0x40 0x20 read-write 0x00000000 LO Line Offset 0 14 0 16383 NLR NLR number of line register 0x44 0x20 read-write 0x00000000 PL Pixel per lines 16 14 0 16383 NL Number of lines 0 16 0 65535 LWR LWR line watermark register 0x48 0x20 read-write 0x00000000 LW Line watermark 0 16 AMTCR AMTCR AHB master timer configuration register 0x4C 0x20 read-write 0x00000000 DT Dead Time 8 8 0 255 EN Enable 0 1 EN Disabled Disabled AHB/AXI dead-time functionality 0 Enabled Enabled AHB/AXI dead-time functionality 1 FGCLUT FGCLUT FGCLUT 0x400 0x20 read-write 0x00000000 APLHA APLHA 24 8 RED RED 16 8 GREEN GREEN 8 8 BLUE BLUE 0 8 BGCLUT BGCLUT BGCLUT 0x800 0x20 read-write 0x00000000 APLHA APLHA 24 8 RED RED 16 8 GREEN GREEN 8 8 BLUE BLUE 0 8