Struct stm32wlxx_hal::pac::i2c1::cr1::R

pub struct R(/* private fields */);
Available on crate feature stm32wl5x_cm4 only.
Expand description

Register CR1 reader

Implementations§

§

impl R

pub fn pe(&self) -> BitReaderRaw<PE_A>

Bit 0 - Peripheral enable

pub fn txie(&self) -> BitReaderRaw<TXIE_A>

Bit 1 - TX Interrupt enable

pub fn rxie(&self) -> BitReaderRaw<RXIE_A>

Bit 2 - RX Interrupt enable

pub fn addrie(&self) -> BitReaderRaw<ADDRIE_A>

Bit 3 - Address match interrupt enable (slave only)

pub fn nackie(&self) -> BitReaderRaw<NACKIE_A>

Bit 4 - Not acknowledge received interrupt enable

pub fn stopie(&self) -> BitReaderRaw<STOPIE_A>

Bit 5 - STOP detection Interrupt enable

pub fn tcie(&self) -> BitReaderRaw<TCIE_A>

Bit 6 - Transfer Complete interrupt enable

pub fn errie(&self) -> BitReaderRaw<ERRIE_A>

Bit 7 - Error interrupts enable

pub fn dnf(&self) -> FieldReaderRaw<u8, DNF_A>

Bits 8:11 - Digital noise filter

pub fn anfoff(&self) -> BitReaderRaw<ANFOFF_A>

Bit 12 - Analog noise filter OFF

pub fn txdmaen(&self) -> BitReaderRaw<TXDMAEN_A>

Bit 14 - DMA transmission requests enable

pub fn rxdmaen(&self) -> BitReaderRaw<RXDMAEN_A>

Bit 15 - DMA reception requests enable

pub fn sbc(&self) -> BitReaderRaw<SBC_A>

Bit 16 - Slave byte control

pub fn nostretch(&self) -> BitReaderRaw<NOSTRETCH_A>

Bit 17 - Clock stretching disable

pub fn wupen(&self) -> BitReaderRaw<WUPEN_A>

Bit 18 - Wakeup from STOP enable

pub fn gcen(&self) -> BitReaderRaw<GCEN_A>

Bit 19 - General call enable

pub fn smbhen(&self) -> BitReaderRaw<SMBHEN_A>

Bit 20 - SMBus Host address enable

pub fn smbden(&self) -> BitReaderRaw<SMBDEN_A>

Bit 21 - SMBus Device Default address enable

pub fn alerten(&self) -> BitReaderRaw<ALERTEN_A>

Bit 22 - SMBUS alert enable

pub fn pecen(&self) -> BitReaderRaw<PECEN_A>

Bit 23 - PEC enable

Methods from Deref<Target = R<CR1_SPEC>>§

pub fn bits(&self) -> <REG as RegisterSpec>::Ux

Reads raw bits from register.

Trait Implementations§

§

impl Deref for R

§

type Target = R<CR1_SPEC>

The resulting type after dereferencing.
§

fn deref(&self) -> &<R as Deref>::Target

Dereferences the value.
§

impl From<R<CR1_SPEC>> for R

§

fn from(reader: R<CR1_SPEC>) -> R

Converts to this type from the input type.

Auto Trait Implementations§

§

impl RefUnwindSafe for R

§

impl Send for R

§

impl Sync for R

§

impl Unpin for R

§

impl UnwindSafe for R

Blanket Implementations§

source§

impl<T> Any for Twhere T: 'static + ?Sized,

source§

fn type_id(&self) -> TypeId

Gets the TypeId of self. Read more
source§

impl<T> Borrow<T> for Twhere T: ?Sized,

source§

fn borrow(&self) -> &T

Immutably borrows from an owned value. Read more
source§

impl<T> BorrowMut<T> for Twhere T: ?Sized,

source§

fn borrow_mut(&mut self) -> &mut T

Mutably borrows from an owned value. Read more
source§

impl<T> From<T> for T

source§

fn from(t: T) -> T

Returns the argument unchanged.

source§

impl<T, U> Into<U> for Twhere U: From<T>,

source§

fn into(self) -> U

Calls U::from(self).

That is, this conversion is whatever the implementation of From<T> for U chooses to do.

source§

impl<T, U> TryFrom<U> for Twhere U: Into<T>,

§

type Error = Infallible

The type returned in the event of a conversion error.
source§

fn try_from(value: U) -> Result<T, <T as TryFrom<U>>::Error>

Performs the conversion.
source§

impl<T, U> TryInto<U> for Twhere U: TryFrom<T>,

§

type Error = <U as TryFrom<T>>::Error

The type returned in the event of a conversion error.
source§

fn try_into(self) -> Result<U, <U as TryFrom<T>>::Error>

Performs the conversion.